ADEX

5 PORT PILOT OPERATED SOLENOID VALVE

ADEX Valves

A00, A05, A12 Series

February 2010

ADEX VALVE

Parker Hannifin Corporation
Pneumatic Division

2

ADEX VALVE

CONTENTS

FEATURE ------------------------------------------------------- 4
Difference between P and R type ---------------------- 7
SIZING MAP ---------------------------------------------------- 7
VARIATIONS OF SOLENOID VALVE -------------------- 8
VARIATIONS OF MANIFOLD ------------------------------ 10
FOR SAFETY USE ------------------------------------------- 12
SOLENOID VALVE/COMMON INSTRUCTIONS ----- 13
ADEX VALVE/INDIVIDUAL INSTRUCTIONS ---------- 17
ADEX VALVE PR type --------------------------------------- 27

A05P Series (Sub-base mounting) -------------------- 28
A05R Series (In-line mounting) ------------------------- 32
Individual wiring type manifold -------------------------- 39
Multipin connector type manifold ----------------------- 48
A12P Series (Sub-base mounting) -------------------- 58
A12R Series (In-line mounting) ------------------------- 65
Individual wiring type manifold -------------------------- 72
Multipin connector type manifold ----------------------- 78
ADEX VALVE A00S Series --------------------------------- 86
A00S Series (Sub-base mounting) -------------------- 87
Individual wiring type manifold -------------------------- 92
ADEX VALVE Manifold Specifications ------------------- 96

Parker Hannifin Corporation
Pneumatic Division

3

ADEX VALVE

A Series
A Series
A Series

Compact body with large flow Quick response time,
faster than 10ms
Body width remains the same, but the flow rate 1.5 to 3
(A05 series, Single solenoid)
times more than conventional valves. Uniquely designed pilot valve cut down on response
time to faster than 10ms saving power consumption.
(In comparison with KURODA products)
Expected life time more
It allows flexibility on your applications saving space and than 50,000,000 operations
reducing costs.
This series is most suitable for driving cylinders of φ 10 to (Based on KURODA's test conditions)
φ 100 in diameter. A well-reputed TS (Triple Squeeze) seal is employed in
the main spool. resulting in low sliding friction and long
A W : 28mm H : 80mm L : 74mm service life.

Body width Effective area Low power consumption
Only 0.6W
10 mm 5.8 mm 2
(With indicator light and surge suppressor)
A W : 41mm H : 61mm L : 93mm Current required is 25mA on 24V DC.
Direct drive from PLC is possible, contributing to cost
Body width Effective area reduction as well as down-sizing of the DC power
supply.
15 mm 11.1 mm2
Multipin connector manifold

Two types of connectors, D sub-connector and a flat
cable connector are provided for wiring between the
manifold and control device, allowing either to be
selected in relation to various control devices used.

Parker Hannifin Corporation
Pneumatic Division

4

ADEX VALVE

Cylinder ports 2 and 4 selectable

(In-line mounting type)

Series Standard Option
Tapped hole Push-in fitting

A M5 φ 4 φ 6

A Rc 1/8 φ6 φ8

AB plate AB plate
(With push-in (Tapped hole type)
fitting)

Locking button (Manual override)

Screwdriver-operated manual override is standard.
It can be used as a hand-operated locking button by fitting
an optional locking cover.

Hand-operated locking cover

Multipurpose tag available

(Sub-base mounting type)
For the convenience of installation, testing, maintenance
tag can be mounted on the upside of solenoid valve body.

Tag

Captured exhaust from
main valve and pilot valve

(Sub-base mounting type & manifold)
Exhaust air from pilot valve is captured together with
exhaust air from main valve.
Unlike conventional exhaust systems, exhaust air from
pilot valve is not directly discharged to the atmosphere.
This prevents air contamination in the atmosphere.

Parker Hannifin Corporation
Pneumatic Division

5

ADEX VALVE

ADEX VALVE
A 0 5 Series
A 12 Series

Parker Hannifin Corporation
Pneumatic Division

6

ADEX VALVE Difference between P and R type.

A 00Series

A05P A05R
A12P A12R
Sub-base mounting type In-line mounting type

Sizing map

Cylinder Cylinder bore size (mm)
Series Conditions Speed
(mm/s) φ 6 φ 10 φ 16 φ 20 φ 25 φ 32 φ 40 φ 50 φ 63 φ 80 φ 100 φ 125

Speed Controller SP-H-M5 SP-2H-1 SP-2H-2

SP-06-1 SP-06-2 SP-15-3 SP-20-4

150

300

A Pressure 0.5MPa 450
Load factor 30% 600
Tube φ 6× 1m

750

900

150

300

A Pressure 0.5MPa 450
Load factor 30% 600
Tube φ 8× 1m

750

900

As cylinder speeds vary according to operating conditions and configurations, use the data as a guide onry for selection.

Parker Hannifin Corporation
Pneumatic Division

7

ADEX VALVE

Solenoid valve variations (Lower case)

Function Voltage Wiring

2-position 3-position
Series
Effective area (mm2) DC24V

Single solenoid
Double solenoid
Closed center
Exhaust center
Pressure center
Plug-in connector with
lead wire from the side
Plug-in connector with
lead wire from the bottom

Sub-base version

A P 5.8

○○ ○○ ○ ○

PR A P 11.1
type In-line version A R4

○○ ○○ ○ ○ ○ ○

A R 8.8

Parker Hannifin Corporation
Pneumatic Division

8

ADEX VALVE

Manual Bracket Port size Special application
override External pilot
Push-in Fitting
Indicator light & (Only at ports 2,4) Vacuum
surge suppressor Low pressure
Screwdriver-operated M5 Rc Rc Rc Pressurizing ports 3,5
locking button Resistant to ozone
Hand-operated 1/8 1/4 3/8 φ 4 φ 6 φ 8 φ 10
locking button
Foot bracket
Side bracket

Single sol.
only

●Standard Optional Made to order

Parker Hannifin Corporation
Pneumatic Division

9

ADEX VALVE

Manifold variations

Manifold
Mountable

solenoid valve
series

Sub-base version MFC PR type
Bar type
In-line version Compact type AP
Individual wiring
AP
MFS AP
Bar type AP
Individual wiring AP

MFX AP
Bar type
Individual wiring AP
Common external pilot AP
MCC AP
Bar type AP
Compact type AR
Multipin connector AR
AR
MCS AR
Bar type
Multipin connector Parker Hannifin Corporation
Pneumatic Division
MCX
Bar type
Multipin connector
Common external pilot

MFU
Bar type
Individual wiring

MCU
Bar type
Multipin connector

10

ADEX VALVE

Wiring Port size Special application
ports 2, 4 External pilot
Connecting Polarity ports1, 3, 5 Push-in fitting
method
Flat cable
D sub-connectorRc Rc M5 Rc Rc φ4 φ6
Pluse common1/8 1/4 1/8 1/4

(NPN)
Minus common

(NPN)
Vacuum
Low pressure
Pressurizing
port 3, 5
Resistant to ozone
φ 8 φ10

Standard Made to order

Parker Hannifin Corporation
Pneumatic Division

11

ADEX VALVE

FOR SAFETY USE

Be sure to read the following instructions before use.
For common and individual instructions, refer to the text of this catalogue.

Pneumatic fluid power-General rules relating to systems

Parker Hannifin Corporation
Pneumatic Division

12

ADEX VALVE

Solenoid valves/Common instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and instructions mentioned for each series of solenoid valves.

Design Design

WARNING CAUTION

Stopping actuator at intermediate position Applying current momentarily

When stopping the actuator at an intermediate position using a When using a double-solenoid type valve, apply current for the
solenoid valve listed in this catalogue, it is difficult to stop it prescribed period of time (0.1 sec.). If current is not applied for
accurately because of the compressibility of air, unlike a hydrau- the prescribed period of time, the solenoid valve may not
lic cylinder can dose. perform the diverting action acording to circumstances.
In addition, as the solenoid valve and air cylinder allow a certain
degree of air leak, they cannot stop at the fixed position for a Leak current
long period of time according to circumstances. When it is
required to stop them at the fixed position for a long period of When a C-R element is used in the contact protective circuit
time, contact KURODA. (surge voltage protection), leak current will flow through the C-R
element.
Keeping pressure (including vacuum) If this leak current becomes large, a malfunction will occur.
Therefore, reduce leak current to less than 1 mA.
As the solenoid valve is designed to allow a certain degree of air
leak, it cannot be used to keep pressure (including vacuum) in a Contact C-R circuit
pressure vessel etc. Power supply

Do not use for emergency shutoff valves. Leak current

Solenoid valves listed in this catalogue are not designed for use Solenoid
in emergency shutoff valves and other safety applications.
When using the solenoid valve for such applications, provide an Use at low temperature
independent means to assure safety.
When using a solenoid valve at 5 or below, provide an air
Exhausting residual air dryer or other proper means to prevent moisture from solidifying
or freezing.
Provide a residual air exhausting function in due consideration of
maintenance and inspection. Doing maintenance and inspection Use with air blow
without exhausting residual air may sometimes malfunction the
actuator. When using a solenoid valve with air blow, select a direct-
When using a 3-position closed center type solenoid valve, operated type or external pilot type solenoid valve.
compressed air is shut in between solenoid valve and actuator When an internal pilot type solenoid valve is used, it may not
even if residual air from the air supply side to the solenoid valve perform the diverting action due to a pressure drop at the time
is exhausted. of air blow.
Therefore, provide a means to exhaust the residual air pressure When an external pilot type solenoid valve is used, supply
separately. compressed air within the specified pressure range to the pilot
port.
Use in vacuum
Mounting position and direction
When using a solenoid valve for diverting vacuum and other
applications, check specifications for the valve and select a A solenoid valve can be mounted in any position and direction
proper one that can be used in vacuum. as a general.
In order to prevent sucking foreign matters from the suction pad However, a metal seal type double-solenoid valve and a 3-position
and exhaust port, provide an inline filter between the suction solenoid valve should be mounted so that the spool may be
pad and solenoid valve and at the exhaust port. horizontal.

Applying current continuously for long time Shock and vibration

When using a solenoid valve while applying current to it Reduce shocks and vibrations applied to the solenoid valve to
continuously for a long period of time, contact KURODA less than the prescribed value. (refer to specifications.)
beforehand. Applying shocks and vibrations exceeding the prescribed value
may rsult in a malfunction of the solenoid valve.
Avoid applying current simultaneously.

When using a double-solenoid valve while applying current to it
continuously for a long period of time, do not apply current to
both solenoids simultaneously ; otherwise the coil may be burnt
out or the main valve may malfunction.

Remodeling the solenoid valve

Do not remodel the solenoid valve.

Parker Hannifin Corporation
Pneumatic Division

13

ADEX VALVE

Solenoid Valves/Common instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and instructions mentiond for each series of solenoid valves.

Selection Piping

WARNING CAUTION

Refer to specifications. Before piping

Solenoid valves listed in this catalogue are designed for Thoroughly flush the inside of each pipe to remove chips,
compressed air. When using other fluid than compressed air, coolant, dust, etc. before piping.
contact KURODA beforehand.
Do not use a solenoid valve at pressure and temperature How to wind a seal tape
outside the range of specifications, otherwise resulting in a
breakdown or malfunction. When winding a seal tape around the threaded portion, leave
space of 1.5 to 2 thread turns.

Mounting Leave space of When screwing,
1.5 to 2 turns. seal tape enters
WARNING equipment,
causing air leak.
When mounting the solenoid valve, firmly fix it while
using care to prevent the stationary part and joint (Good) (No good)
from loosening.
How to apply liquid sealant
If the solenoid valve is mounted with insufficient strength, it may
sometimes come off. When applying liquid sealant to the threaded portion, apply a
proper amount to about 1/3 of the periphery of the threaded
Do not start the system until it is ensured that equip- portion and then screw it.
ment works properly.
Joint Sealant Apply sealant to this portion.
After mounting the solenoid valve, connect power supply and ↓ ↓
then perform a functional test and a leak test. Check that it has 13
been correctly mounted and works properly, before starting the
system. Screw of pipe and joint

Coating with paint When screwing the pipe and joint, use care to prevent chips
and sealant from entering the pipe and joint.
When coating the resin portion with paint, it may be adversely Tighten them within a proper range of clamping torque.
affected by paint and solvent. For the propriety of painting,
contact KURODA beforehand. Port size Clamping torque (N.m)
Do not peel off the nameplate affixed on the solenoid valve and M3 0.3 0.5
do not erase or smear out the letter on it. M5 1.5 2.0
R, Rc1 8 7.0 9.0
Provide space for maintenance and inspection. R, Rc1 4 12.0 14.0
R, Rc3 8 22.0 24.0
CAUTION R, Rc1 2 28.0 30.0
R, Rc3 4 28.0 30.0
Fit an air muffler to the exhaust port (ports 3 5) of R, Rc1 36.0 38.0
the solenoid valve. R, Rc11 4 40.0 42.0
R, Rc11 2 48.0 50.0
Dust or foreign matter that enters it may cause a malfunction of
the solenoid valve.

Do not wipe off the model name inscribed on a
nameplate etc. with organic solvent.

The inscribed indication may be erased.

Parker Hannifin Corporation
Pneumatic Division

14

ADEX VALVE

Solenoid valves/Common instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and instructions mentioned for each series of solenoid valves.

Piping Operating enviroments

CAUTION DANGER

Avoid wrong piping. Do not use solenoid valve in a explosive environment.

When connecting a pipe to a solenoid valve, be careful not to WARNING
mistake the supply port by referring to the nameplate affixed to
the product or the product catalogue. Do not use a solenoid valve in atmospheres containing
corrosive gases, chemicals, seawater, water and vapor
When using a 3-position closed center type solenoid and in places where a solenoid valve contacts these
valve : matters.

Thoroughly check the piping between solenoid valve and Do not use a solenoid valve in a place where vibrations
actuator for air leak. or shocks are directly applied to it.

Wiring When a solenoid valve is exposed to the direct
sunlight, fit a protective cover to the solenoid valve.
WARNING
When a solenoid valve is located around a heat
When doing wiring work, be sure to turn off compressed source, shut off the radiant heat.
air and power supplies beforehand.
When installing a solenoid valve in the control panel,
Wiring work without turning off air and power supplies may take proper heat-radiating measures so that the
cause an electric shock or malfunction ; this sometimes results inside temperature may be kept within the specified
in an injury to the human body or a damage to property. temperature range.

Avoid mis-wiring. When using a solenoid valve in a place where it is
exposed to welding spatters, provide a protective
Some solenoid valves have polarity : Those operating on DC cover or other proper prevention.
with built-in indicator light and those equipped with surge
protective circuit. Welding spaters may burn out the plastic parts of the solenoid
When wiring to a solenoid valve, check whether or not it has valve, sometimes resulting in a fire.
polarity.
For a solenoid valve having polarity, check the lead wire color Lubrication
and symbol of the polarity by the catalogue or actual article
beforehand and then make correct wiring. CAUTION
Mis-wiring will result in the following problems :
(Where no polarity protective diode is incorporated :) Solenoid valves listed in this catalogue are non-
Wiring to the wrong polarity will burn out the diode in the lubrication.
solenoid valve, the switching element on the control unit side or
the power supply unit. The non-lubricated solenoid valve can be used without
(Where a polarity protective diode is provided :) lubrication, but can be used with lubrication.
Wiring to the wrong polarity will not cause the solenoid valve to When using it with lubrication, do not discontinue supplying oil.
perform a diverting action. Otherwise, the applied lubricant may run off, sometimes
resulting in an operation failure.
Avoid applying stress and tensile force to lead wire When using a lubricant, Class 1 turbine oil ISO VG 32 (con-
repeatedly. tainning additive) is recommended.

Wiring made in such a manner that stress and tensile force are
repeatedly applied to the lead wire will result in the breaking of
wire. Provide some degree of margin for wiring.

Check that there is no insulation failure.

If an insulation failure occurs in the lead wire connection,
extension cable and terminal base, an excess flows to the
switching element of the solenoid valve or control unit,
sometimes resulting in a damage.

Do not mistake applied voltage.

Mistake in applied voltage in case of wiring to a solenoid valve
will cause an operation failure or burn out the coil.

After completion of wiring, check for wrong
connection before turning on power.

Parker Hannifin Corporation
Pneumatic Division

15

ADEX VALVE

Solenoid Valves/Common instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and instructions mentioned for each series of solenoid valves.

Quality of air Maintenance and inspection

WARNING WARNING

Use pure air. Inspection before maintenance

Compressed air containing corrosive gases, chemicals, salt, First check that load drop prevention has been provided.
etc. causes a breakdown or operation failure. So do not use Then shut off air and power supplies to the system and exhaust
such air. residual air in the system beforehand.
For a 3-position closed center type solenoid valve, compressed
CAUTION air is sealed between solenoid valve and cylinder.
Exhaust this residual compressed air.
Fit an air filter with filtration of 5 µm or fine.
Inspection after maintenance
Install an air dryer.
When restarting the system, check that preventive measures
Compressed air containing much drainage causes the operation against flying-out of the actuator have been taken. Then
failure of pneumatic equipment. Install an air dryer, lower the connect compressed air supply to the pneumatic system, and
temperature and reduce drainage. perform a proper functional test and a leak test to check that it
works safely without fail, before starting the system.
Take proper countermeasures against sludge.
Operation at low frequency
If sludge produced in compressor oil enters pneumatic equip-
ment, it will cause the operation failure of pneumatic equipment. To prevent an operation failure, perform the switching action of
It is recommendable to use compressor oil (NISSEKI FAIRCALL the solenoid valve once per 30 days. (Be careful of air supply.)
A68, IDEMITSU DAPHUNY SUPER CS68) featuring minimized
sludge production or use a sludge filter or mist cleaner to Manual operation
prevent sludge from entering the pneumatic equipment.
When the solenoid valve is manually operated, the system
Filter Sludge filter Regulator connected to it is also operated. Make sure safety before
Mist cleaner operation.

Disassembly of solenoid valve

When disassembling the solenoid valve, contact KURODA
beforehand.

CAUTION

Draining

To keep the quality of air to a certain level, drain the air filter at
periodical intervals.

Parker Hannifin Corporation
Pneumatic Division

16

ADEX VALVE

ADEX Valve/Individual instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and common instructions.

Flow rate Port identification

Flow rate can be calculated from the following formula : CAUTION

For values in the sonic velocity zone. find out from the attached table.

PH 1.89PL (Subsonic velocity zone) Port mark

Q 240 × S× PL× (PH PL) × 293 Piping port marks such as P 1 , A 4 conforming to JIS and ISO
TH are given in the respective piping port positions.
PH 1.89PL (Sonic velocity zone)

Q 120 × S× PH × PH × 273 JIS ISO Use
TH
Q Flow rate r /min(ANR)

S Effective area of orifice mm2 P 1 Supply port

PH Pressure on upper stream MPa abs A 4 Output port

PL Pressure on down stream MPa abs B 2 Output port

TH Absolute temperature on upper stream K R1 5 Exhaust port

(Note) Absolute pressure (MPa) Supply pressure 0.100 (MPa) R2 3 Exhaust port

Sonic velocity zone (at 20 X : External pilot port
Y : Pilot valve captured exhaust port

Type of port thread

Type of port thread is marked on the sub-base by the following
abbreviation.

Abbrev. Type of thread

R Rc

Flow rate /min(ANR) GG

N NPT

Pressure MPa F NPTF Mark

Port mark
Thread type mark

Effective area mm 2 Using 5-port valve as 3-port valve

( When the value of effective area is 10 1 or )10 n, CAUTION
multiply the same figure by the flow rate.

Effective area A05 and A12 Series are so designed that each of them can be
used as a 3-port valve with normal close (NC) or normal open
Effective areas mentioned in this catalog are measured between (NO) function. However, use it with port opened.
ports 1→2, 4 in accordance with JIS (JAPANESE INDUSTRIAL This function is useful when 3-port double solenoid valve
STANDARD) B8374/8375. is required.

Plug position Port 4 Port 2
Function NO NC

Number of solenoid 42 42
Duble solenoid Single solenoid
513 513
42 42

513 513

Parker Hannifin Corporation
Pneumatic Division

17

ADEX VALVE

ADEX Valve/Individual instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and common instructions.

Continuous energizing TAG

CAUTION CAUTION

When ADEX VALVE is continuously energized with power turned Do not reuse a tag that was once attached to same place.
on for a long period of time, the solenoid may heat up, resulting Otherwise, it may be too loose.
in a damage to the packing and gasket according to circumstances.
However, ADEX VALVE can be used under the following conditions : Air exhaust

Operating ambient temperature : Below 40 CAUTION
Rated operating voltage (Only DC) : 0 10%
The following models can be used under good heat-adiating As this solenoid valve is so constructed that exhaust air from
conditions : pilot valve and exhaust air from main valve are collected at ports
3, 5 use care that exhaust air is not extremely choked.
Single item of A00 Otherwise, it may cause a malfunction.
Single item of A05P and A05R, and bar type manifolds When operating 5 or more solenoid valves simultaneously on a
(MFS, MCS, MCC and MCU), except when MFC, MFU, MFX manifold of 10 or more stations, open both sides of ports 3, 5.
or single item is mounted on a plane. (For common external pilot type, also open port Y.)
Single item of A12P, A12R, A20P and A20R, and bar type (The bar type manifold is open on both sides. For a separate
manifolds (MFS, MFX, MFU, MCS, MCX and MCU). type manifold, place PR blocks on both sides.)

When operating ADEX VALVE with power continuously turned Pressure supply
on in other conditions than above-mentioned, be sure to consult (For external pilot type)
KURODA beforehand.
CAUTION
Selection of proper
configuration fitting Supply pressure to external pilot valve from port X. (Port Y is
pilot valve exhaust port.)
CAUTION When supplying air pressure, first supply external pilot pressure
and then supply main valve pressure.
There is the possibility that some fitting cannot be fitted to ports To cut the pressure supply and exhaust air, do so for the main
2 and 4 (manifold, sub-base, and AB plate) of this solenoid valve valve first and then for the external pilot valve.
because there are various fitting makers supplying different types
of fittings.
Check the size of the intended fitting by referring to the catalogue
supplied by the fitting maker.
Note that the pitch between ports 2 and 4 (AB plate) of the in-line
mounting type valve is designed to be a minimum.

Tightening torque for mounting screw

CAUTION

Recommended tightening torque range is shown as below.

Name Screw size Torque (N m)
M2 0.2 0.22
A05 solenoid valve mounting screw
blank plate mounting screw M3 0.5 0.55
M2 0.18 0.2
A12 solenoid valve mounting screw M3 0.8 1.0
blank plate mounting screw M1.6 0.08 0.1

A05 AB plate mounting screw

A12 AB plate mounting screw

A00 solenoid valve mounting screw
blank plate mounting screw

Parker Hannifin Corporation
Pneumatic Division

18

ADEX VALVE

ADEX Valve/Individual instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and common instructions.

How to use connectors Connector ass’y
with protective cover
CAUTION
CAUTION
When doing wiring work, be sure to turn off power beforehand.
Prevents short-circuiting caused by the entry of foreign matters
How to attach and detach a connector into the connector.

When attaching a connector, pinch the clip with your finger and The cover is made of chloroprene rubber for electrical use,
insert the connector into the pin straight to the end. When assuring excellent weather and insulation resistance. However,
detaching a connector, pinch the clip with your finger and pull be careful not to place it under splash of cutting oil etc.
out the connector straight.
Neat appearance owing to use of round cord.
Connector Connector Ass'y with protective cover is optionally available.
Specify the following model No. when ordering.

A05P-DC-CB10

Clip 14.8 18.3

PR type

9.9

Pin 11 15 98
Connector
1000

Red Black

Parker Hannifin Corporation
Pneumatic Division

19

ADEX VALVE

ADEX Valve/Individual instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and common instructions.

Internal circuit of solenoid with
indicator light and surge suppresor

CAUTION Minus common (PNP)

For DC24V :

Plus common (NPN)
PR type

Red( )

Black( )
Make connection in accordance with polarity marks ( ) ( ).

Parker Hannifin Corporation
Pneumatic Division

20

ADEX VALVE

ADEX Valve/Individual instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and common instructions.

Manual override

WARNING Hand-operated locking manual override (Option)

Screwdriver-operated locking manual override The screwdriver-operated locking button can be used as a
(Standard) hand-operated locking button by fitting an optional locking
No-locking operation cover.

Push the locking button with a screwdriver, and the valve shifts How to fit a locking cover
to energized position. When the screwdriver is released from
the locking button, the valve is reset to non-energized position. Adjust the rib provided inside the locking cover to 2 respective
groove on the circumference of the screwdriver-operated
Locking operation locking button and insert the cover.
Then rotate it clockwise by 30˚. Thus, the locking cover has
Push the locking button with a slotted screwdriver and rotate been completely fitted. (To remove the locking cover, reverse
the button clockwise by 90˚. the above-mentioned procedure.)
The valve is locked to keep energized position.
When the button is rotated counterclockwise by 90˚ and the Rib Locking cover
screwdriver is released from the button, the valve is reset to
non-energized position.
Use a screwdriver with blade width of 2.3 to 2.4 mm.

PR type

Groove

(Locked position) No-locking operation

Push the locking button with your finger, and the valve shifts to
energized position. When the finger is released from the locking
button, the valve is reset to non-energized position.

Locking operation

Push the locking button with your finger and rotate the button
clockwise by 90˚.
The valve is locked to keep energized position.
When the button is rotated counterclockwise by 90˚ and your
finger is released from the button, the valve is reset to non-
energized position.

PR type

Parker Hannifin Corporation
Pneumatic Division

21

ADEX VALVE

ADEX Valve/Individual instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and common instructions.

Individual supply spacer Individual exhaust spacer

CAUTION CAUTION

Mounting an individual supply spacer between solenoid valve and Mounting an individual exhaust spacer between solenoid valve and
manifold makes it possible to provide each solenoid valve with an manifold makes it possible to provide each solenoid valve with an
individual supply port. However, the types of manifolds to which individual exhaust port. However, the types of manifolds to which
these spacers can be mounted are specified as follows : As individual these spacers can be mounted are specified as follows : As individual
supply spacers are optionally available, please order by the model exhaust spacers are optionally avalable, please order by the model
number shown below. number shown below.

Model No. Applicable manifold Model No. Applicable manifold

□Individual wiring type MFS -A05P-01 □Individual wiring type MFS -A05P-01
□A05PA-IS-M5 Multipin connector type MCC -A05P-M5(C4, C6) □A05PA-IE-M5 Multipin connector type MCC -A05P-M5(C4, C6)
□MCS -A05P-01
□MCS -A05P-01
□A05RA-IS-M5 Multipin connector type MCU -A05R-M5(C4, C6) □A05RA-IE-M5 Multipin connector type MCU -A05R-M5(C4, C6)
□A12PA-IS-01 Individual wiring type MFS -A12P-02 □Individual wiring type MFS
□Multipin connector type MCS -A12P-02(C6, C8) -A12P-02
A12PA-IE-01
□Multipin connector type MCS -A12P-02(C6, C8)

A05PA-IS-M5, A12PA-IS-01 A05PA-IE-M5, A12PA-IE-01

Set Screw Set Screw
Clamping torque Clamping torque
0.25 0.3N m 0.25 0.3N m

Mounting position
mark

Individual supply spacer Individual exhaust spacer

M5 Base gasket M5 (Both sides) Base gasket
(Port 1) (Port 3,5)

(Note) Mounting height of individual supply spacer (Note) Mounting height of individual exhaust spacer
A05 : 18.5 mm, A12 : 20 mm A05 : 18.5 mm, A12 : 20 mm
When mounting a supply spacer, turn port 1 toward the When mounting an exhaust spacer, turn the mounting
end cover side in case of single solenoid valve. position mark (shown in the above figure) toward the end
cover side in case of single solenoid valve.
A05RA-IS-M5 Be sure to connect a pipe to the exhaust port on the pilot
valve side and protect the wiring from drain.

Set Screw A05RA-IE-M5 Set Screw

Clamping torque Clamping torque
0.25 0.3N m 0.25 0.3N m

Individual supply spacer Individual exhaust spacer
Base gasket
M5 M5 (Both sides)
(Port 1) (Port 3, 5)

Base gasket

(Note) Mounting height of individual supply spacer : 18.5 mm (Note) Mounting height of individual exhaust spacer : 18.5 mm
Be sure to connect a pipe to the exhaust port on the pilot
valve side and protect the wiring from drain.

Parker Hannifin Corporation
Pneumatic Division

22

ADEX VALVE

ADEX Valve/Individual instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and common instructions.

Specifications for multipin connector type manifolds

CAUTION

This manifold allows wiring to each solenoid valve to be made on a
printed circuit board and allows wiring from the outside to be
collectively made using a D sub-connector or flat cable connector,
thereby reducing the number of connections and providing a neat
appearance. Use of connectors based on MIL specification
broadens the compatibility of this manifold.

Wiring specifications for D sub-connector (25-pole) Valve numbering order

Valve No. Valve No. Valve No.
(Number of stations)
No. 1 No. 1 Sol.14
No. 2 No. 2 (L) (R)
No. 3 No. 3 Sol.12
No. 4 No. 4 Notch
No. 5 No. 5 MIL connector
No. 6 No. 6 mounting position
No. 7 No. 7
No. 8 No. 8
No. 9 No. 9
No. 10 No. 10
No. 11 No. 11
No. 12 No. 12
(commn) (commn)

Plus common (NPN) Minus common (PNP)

D sub-connector Ass'y (Note) Internal wiring of manifold is connected to Sol.14, Sol.12
Ordering Instructions and D sub-connector terminal on common specifications.
DSS-R25FB-1K
Count the number of stations based on the L side of D
sub-connector mounting position.

Example : 1-station, 2-station, n-station

Maximum number of stations is 12 for manifold and 24
for solenoid.

For your specific requirement for more than the maximum
number of stations, contact KURODA.

When wiring with flat cable be careful of external surge
voltage.

Cable length 1K : 1m F type R type
2K : 2m
66 66
Color B : Black 27.5 38.5
Connector position F : Ftype 38.5 27.5

R : Rtype 21 29 36 36 29 21
Number of pin 25 : 25pins

55 2-M2.6 2-M2.6 55

20 20 47
47

Parker Hannifin Corporation
Pneumatic Division

23

ADEX VALVE

ADEX Valve/individual instructions

Be sure to read them before use.
Also refer to Par. "For Safety Use" and common instructions.

Specifications for multipin connector type manifolds

Wiring specifications for flat cable connector (26-pole)

Valve No. Valve No. VA LVE NUMBERING ORDER Sol.14
Valve No. (R)
No. 1 No. 1 (Number of stations) Sol.12
No. 2 No. 2
No. 3 No. 3 (L)
No. 4 No. 4
No. 5 No. 5
No. 6 No. 6
No. 7 No. 7
No. 8 No. 8
No. 9 No. 9
No. 10 No. 10
No. 11 No. 11
No. 12 No. 12
(commn) (commn)

Plus common (NPN) Minus common (PNP) Notch

MIL connector
mounting position

Flat cable connector (Note) Internal wiring of manifold is connected to Sol.14, Sol.12
and flat cable connector terminal on common specifications.
Use a product conforming to MIL-C 83503/7A.
Count the number of stations from the L side of flat cable
connector mounting position.

Example :1-station, 2-station, n-station

Maximum number of stations is 12 for manifold and 24
for solenoid.

For your specific requirement for more than the maximum
number of stations, contact KURODA Pneumatics Ltd..

When wiring with flat cable, be careful of external surge
voltage.

Parker Hannifin Corporation
Pneumatic Division

24

ADEX VALVE

PR TYPE

Parker Hannifin Corporation
Pneumatic Division

25

ADEX VALVE

5 port pilot operated solenoid valve

A05P Series

Rubber Seal /Sub-base Mounting type

A05PS25 2-position
A05PD25 Single solenoid
A05PD35
A05PE35 2-position
A05PO35 Double solenoid

3-position
Closed center

3-position
Exhaust center

3-position
Pressure center

Specifications Unit A05PS25 A05PD25 A05PD35 A05PE35 A05PO35
mm2
Model No. Non-lubricated/lubricated air 6.7
Fluid 0.37
Port size Rc 1/8
Effective area
Cv value 5.8 4.5
Operating ambient temperature
0.32 0.25

5 50

Pressure range MPa 0.15 0.7 0.1 0.7 0.2 0.7

Maximum frequency cycle/min 0.1 0.7 For external pilot operation
600 500

Response ON s 0.010 0.010 0.010
time DC s 0.010 (0.016) 0.015 (0.021)

OFF

Pilot air exhaust Captured exhaust

Manual override Screwdriver-operated locking button

Mounting position Free

Shock resistance, m/s2 150/30
vibration resistance g 67 69
g 126 128
Mass Without sub-base 52
With sub-base 108

(Note) ● Service kit not available
● When temperature of valve site goes down below 5 , complete dry air should be supplied to prevent from freezing.
● Pressure range of external pilot supply : 0.25 0.7MPa
● Response time in bracket ( ) shows with surge suppressor.
● Response time shown above is in accordance with JIS B 8375.
● Effective area shown above is a value between ports 1 and 2, 4.

Electrical Specifications

Rated voltage DC V 24

Permissible voltage fluctuation % 10, 10

Power DC W 0.6 (with indicator light and surge suppressor), 0.55 (without indicator light and surge suppressor)
consumption

Grade of Insulation JIS grade E
Wiring Plug-in connector
Surge suppressor
Indicator light Diode
LED

Parker Hannifin Corporation
Pneumatic Division

26

ADEX VALVE

A05P Series 1 P 01 E

Ordering Instructions Wiring
No mark: Without connector
A05P S25
E : Connector with lead wire
Function (Length : 500mm)
S25 : 2-position, single solenoid
Port size
(A) (B) No mark: Without sub-base
42
513 01 : Rc1/8
G1 : * G1/8
(R1) (P) (R2) N1 : * NPT1/8
F1 : * NPTF1/8
D25 : 2-position, double solenoid (Note) Valve without sub-base comes with a

(A) (B) base gasket & two mounting screws.
42
513 Connector position
P: S:
(R1) (P) (R2)
(With indicator light (Without indicator light
D35 : 3-position, closed center and surge suppressor) and surge suppressor)

(A) (B)
42
513

(R1) (P) (R2)

E35 : 3-position, exhaust center

(A) (B)
42
513

(R1) (P) (R2)

O35 : 3-position, pressure center

(A) (B)
42
513

(R1) (P) (R2)

Voltage
1 : DC24V

Special specification
No mark: standard (Internal pilot)

X : * External pilot
(Pilot air is exhaused
through exclusive port Y.)

* : Made to order

Parker Hannifin Corporation
Pneumatic Division

27

ADEX VALVE

A05P Series

Optional Accessories and Spare parts

Connector with lead wire Sub-base
A05P DC CL5 A05P B 01X

Lead wire length Special specifications
5 : 500mm No mark: Standard
10 : *1000mm
Voltage X : For external pilot
DC : For DC (With port X)

Type Port size
P : For PR type 01 : Rc 1/8
G1 : * G 1/8
N1 : * NPT 1/8
F1 : * NPTF1/8

For PR type DC
( ) Black

( ) Black

(Note) For common use with PR type of A05 and A12

Locking cover Base gasket
A05P LA A05PX G

Color Content of kit
A : Orange SG : Gasket & mounting screws
G : Gasket only (Pack of 10)
(Note) For common use with all A05 and A12 S : Mounting screw only (Pack of 20)
Special specifications
Tag for solenoid valve No mark : Standard
A 0 5 P N (Pack of 10) X : * For external pilot(With port X)

Tag Mounting screw

Solenoid valve Base gasket
(Note) For common use with sub-base mounted type of A05
(Note) For common use with A05P
and A12

*: Made to order

Parker Hannifin Corporation
Pneumatic Division

28

ADEX VALVE

A05P Series

Material Specification

2-position
Single solenoid

2-position
Double solenoid

3-position
Closed center
3-position
Exhaust center
3-position
Pressure center

Main Components Material
Zinc die-casting
No. Description Aluminium/NBR
Body
Spool ass'y Resin
End cover Resin
Piston housing Resin
Piston Refer to A00 Series
Pilot valve NBR
Base gasket Aluminium die-casting
Sub-base

29 Parker Hannifin Corporation
Pneumatic Division

ADEX VALVE

A05P Series 14.5 13.5 (Unit : mm)
19
Dimensions 45 1.5 17
35 5
A05PS25 M5(port Y)
13 11.5 3 (For model with
Connector position: 27.5 symbol X)
P or S
With locking cover
2-φ 3.2
15 (Mounting φ 9.4

hole) 17

17.5 M5(port Y)
X (For model with
symbol X)
Y
With locking cover
M5(Port X) 45
φ 9.4
(For model with 74 Parker Hannifin Corporation
50 24 Pneumatic Division
symbol X) 500 6 Manual override

59.6
56
31.5
24.5
16.5

7.5 11.5 11.5 13.5
22.5 19
5-Rc 1/8 13 11.5 3
27.5
A05PD25 Y

14.5 5.4

Connector position:
P or S

2-φ 3.2 45

15 (Mounting 35 5
hole)

17.5
X

M5(Port X) 500 6 100 6 500
50
(For model with Manual override
symbol X)

50

59.6
56
31.5
24.5
16.5

7.5 11.5 11.5 5.4
22.5
5-Rc1/8

30

ADEX VALVE (Unit : mm)

A05P Series 17

Dimensions M5(port Y)
(For model with
A05PD35, A05PE35, A05PO35 symbol X)

Connector position: 14.5 13.5 With locking cover
P or S 19
45 13 11.5 3 φ 9.4
2-φ 3.2 35 5 27.5
Y
15 (Mounting
hole)

17.5
X

10

M5(Port X)

(For model with

symbol X) 500 6 108 6 500
50
Manual override 58

59.6
56
31.5
24.5
16.5

7.5 11.5 11.5 5.4
22.5
5-Rc 1/8

Parker Hannifin Corporation
Pneumatic Division

31

ADEX VALVE

5 Port pilot operated solenoid valve

A05R Series

Rubber Seal/In-line Mounting type

A05RS25 2-position
A05RD25 Single solenoid
A05RD35
A05RE35 2-position
A05RO35 Double solenoid

3-position
Closed center

3-position
Exhaust center

3-position
Pressure center

Spscifications Unit A05RS25 A05RD25 A05RD35 A05RE35 A05RO35
0.15 0.7
Model No. Non-lubricated / lubricated air 4.5
Fluid 0.25

Port size Port 2, 4 : M5, C4, C6

Port 1, 3, 5 : M5

Effective area mm2 4 3.7
Cv value 0.22
Operating ambient temperature 0.20
600
5 50

Pressure range MPa 0.1 0.7 0.2 0.7

0.1 0.7 For external pilot operation

Maximum frequency cycle/min 500

Response ON s 0.010 0.010 0.010
time DC s 0.010 (0.016) 0.015 (0.021)

OFF

Pilot air exhaust Individual exhaust

Manual override Screwdriver-operated locking button

Mounting position Free

Shock resistance, m/s2 59 150/30
vibration resistance g 76 78

Mass

(Note) ● Service kit not available
● When temperature of valve site goes down below 5 , complete dry air should be supplied to prevent from freezing.
● Pressure range of external pilot supply : 0.25 0.7MPa
● Response time in bracket ( ) shows with surge suppressor.
● Response time shown above is in accordance with JIS B 8375.
● Effective area shown above is a value between ports 1 and 2, 4.

Electrical Specifications

Rated voltage DC V 24
%
Permissible voltage fluctuation W 10, 10

Power DC 0.6 (with indicator light and surge suppressor), 0.55 (without indicator light and surge suppressor)
consumption
JIS grade E
Grade of Insulation Plug-in connector
Wiring
Surge suppressor Diode
Indicator light LED

Parker Hannifin Corporation
Pneumatic Division

32

ADEX VALVE

A05R Series 1 P M5 E

Ordering Instructions Wiring
No mark: Without connector
A05R S25
E : Connector with lead wire
Function (Length : 500mm)
S25 : 2-position, single solenoid
Size of ports 2 and 4
(A) (B) M5 : M5
42 C4 : * With push-in fitting forφ 4
513 C6 : * With push-in fitting forφ 6
Connector position
(R1) (P) (R2) P: S:

D25 : 2-position, double solenoid (With indicator light (Without indicator light
and surge suppressor) and surge suppressor)
(A) (B) Q: B:
42
(With indicator light (Without indicator light
513 and surge suppressor) and surge suppressor)
(R1) (P) (R2)

D35 : 3-position, closed center

(A) (B)
42

513
(R1) (P) (R2)

E35 : 3-position, exhaust center

(A) (B)
42

513
(R1) (P) (R2)

O35 : 3-position, pressure center

(A) (B)
42

513
(R1) (P) (R2)

Voltage
1 : DC24V

Special specification
No mark: standard (Internal pilot)

X : * External pilot

(Pilot air is exhaust
through exclusive port Y.)

* : Made to order

Parker Hannifin Corporation
Pneumatic Division

33

ADEX VALVE

A05R Series

Optional Accessories and Spare parts

Connector with lead wire AB plate
A05P DC CL5 A05R AB M5X

Lead wire length Special specifications
5 : 500mm No mark : Standard
10 : * 1000mm
Voltage X : *For external pilot
DC : For DC
(With port X)
Type Port size
P : For PR type M5 : M5

C4 : * With push-in fitting forφ 4
C6 : * With push-in fitting forφ 6

For PR type DC Mounting Mounting
( ) Black screw screw

( ) Red AB plate AB plate
(Tapped hole (With push-
(Note) For common use with PR type of A05 and A12 type) in fitting)
Plate gasket
Plate gasket

(Note) Gasket & mounting screws are supplied
For common use with A05R

Locking cover Bracket BF
A05P LA A05R
Mounting
Color F : Foot bracket
A : Orange S : Side bracket

(Note) For common use with all A05 and A12 Solenoid
valve
Mounting screw

Foot bracket / F

(Note) Only single
solenoid mountable

Side bracket / S

Mounting screw

Solenoid valve

* : Made to order

Parker Hannifin Corporation
Pneumatic Division

34

ADEX VALVE

A05R Series

Material Specification

2-position
Single solenoid

2-position
Double solenoid

3-position
Closed center
3-position
Exhaust center
3-position
Pressure center

Main Components Material
Zinc die-casting
No. Description Aluminium/NBR
Body
Spool ass'y Resin
End cover Resin
Piston housing Resin
Piston Refer to A00 Series
Pilot valve NBR
Plate gasket Aluminium die-casting
AB plate

35 Parker Hannifin Corporation
Pneumatic Division

ADEX VALVE (Unit : mm)
59
A05R Series

Dimensions

A05RS25

0.7 10 0.7 2-φ 2.1 21
(Mounting hole) 10.2

Push-in fitting for 2- φ 4,φ 6 11M3 (Port X)
(For C4,C6) 15.5 8.5(For model with
25symbol X)
500 6 74 C4:(38.2)
Connector position: 24 C6:(39)
P or S 50

34.6 40.1
31
27.5
22
4

0.4 2-M2.5 Depth 4(Rear surface) 9.6 500 6 6
6.5 (Bracket mounting hole)

9.5 9.5 5-M5 or 3-M5(For C4,C6) 48.3

Connector position:
Q or B

With locking cover

5.4 φ 9.4 With foot bracket

With side bracket 2-φ 3.5
Mounting
hole

1.2 31
14.4 38

24
17

34 2-φ 3.5
27 Mounting hole

33
36.5

28.5

1.2

Parker Hannifin Corporation
Pneumatic Division

36

ADEX VALVE (Unit : mm)

A05R Series

Dimensions

A05RD25

0.7 10 0.7 2-φ 2.1 21 15.5 8.5
Mounting 10.2 25
hole
C4: 38.2
Push-in fitting for 2φ- 4,φ 6 C6: 39
For C4,C6 500 6 5 34.6

Manual override M3 Port X
For model with symbol X
Connector position: 500 6 100
P or S 6 500
50 50 48.5

0.4 34.6 24
31
9.6
27.5
22
6.5
4

2-M2.5 Depth 4 Rear surface 45.5
Bracket mounting hole
Connector position:
9.5 9.5 5-M5 or 3-M5 For C4,C6 Q or B

With locking cover

φ 9.4

5.4

With side bracket

24 1.2
17 14.4

34 2-φ 3.5
27 Mounting hole

33
36.5

Parker Hannifin Corporation
Pneumatic Division

37

ADEX VALVE (Unit : mm)
48.5
A05R Series

Dimensions

A05RD35, A05RE35, A05RO35

0.7 10 0.7 2- φ 2.1 21 8.5
Mounting 10.2
hold

Push-in fitting for 2- φ 4,φ 6

For C4,C6

Manual override M3 Port X
For model with symbol X

Connector position: 500 6 108 6 500
P or S 50 58

34.6 31 27.5 22 15.5 25 500 6 5 34.6
C4: 38.2
C6: 39

4

0.4 6.5 9.6

2-M2.5 Depth 4 Rear surface 45.5
Bracket mounting hole
Connector position:
11 Q or B

9.5 9.5 5-M5 or 3-M5 For C4,C6

With locking cover

φ 9.4

5.4

With side bracket

1.2
14.4

34 2- φ 3.5
27 Mounting hole

33
36.5

Parker Hannifin Corporation
Pneumatic Division

38

ADEX VALVE

Individual wiring type manifold

MF A 0 5 P
Bar type R

MFC□ A05P Common SUP, Common EXH
Ports 2 & 4 on side
Compact type

MFS□ A05P Common SUP, Common EXH
Ports 2 & 4 on side

MFX□ A05P Common SUP, Common EXH
Common external pilot
Ports 2 & 4 on side

MFU□ A05R Common SUP, Common EXH
Ports 2 & 4 on valve body

Manifold Specifications For A05P Series MCX□ A05P For A05R Series

MFC□ A05P MCS□ A05P MCU□ A05R

Type of manifold Common SUP, Common EXH Common SUP, Common EXH Common SUP, Common EXH Common SUP, Common EXH
Pilot valve captured exhaust Pilot valve captured exhaust Common external pilot Pilot valve captured exhaust
Ports 2 & 4 on side Ports 2 & 4 on side Pilot valve captured exhaust Ports 2 & 4 on valve body
Compact type Ports 2 & 4 on side

Ports 1, 3, 5 Rc1/8 Rc1/8 Rc1/8 Rc1/8
M5, C4, C6 M5, C4, C6
Port size Ports 2, 4 Rc1/8 Rc1/8 , C4, C6
Port Y A05PS25 A05RS25
A05PD25 M5 A05RD25
A05PD35 A05RD35
Port X A05PE35 M5 A05RE35
A05PO35 A05RO35
Number of stations 2 20 A05R-BP

Mounting Direct mount

Mountable solenoid valve A05PS25 A05PS25X
A05PD25 A05PD25X
A05PD35 A05PD35X
A05PE35 A05PE35X
A05PO35 A05PO35X

Blank plate A05P-BP

Parker Hannifin Corporation
Pneumatic Division

39

ADEX VALVE

A05P, A05R Series

Ordeing Instruction

Manifold for A05P Series A05P M5

MFC 7

Type of manifold Option 1
MFC : Common SUP, Common EXH B : With bracket

Ports 2 & 4 on side No mark : Without bracket
Compact type (Note) Bracket can be mounted
MFS : Common SUP, Common EXH
Ports 2 & 4 on side only when single solenoid is
MFX : Common SUP, Common EXH
Common external pilot mounted on MFC, MFS type.
Ports 2 & 4 on side
Size of Ports 2 and 4
Number of stations M5 : M5
2 2 station
01 : Rc1/8
20 20station
C4 : *With push-in fitting forφ 4
Mountable solenoid valve series C6 : * With push-in fitting forφ 6
A05P
… Type M5 01 C4 C6
… MFC ○ ○○

MFS ○
MFX ○ ○ ○

(Note) When using G, NPT, NPTF threads,
consult KURODA Pneumatics Ltd.

Mountable solenoid valve For details refer to Pages 26 28. E

A05P S25 1 P

Function Wiring
S25 : 2-position, single solenoid No mark: Without connector

(A) (B) E : Connector with lead wire
42 (Length : 500mm)

513 Size of port 2 and 4
(R1) (P) (R2) No mark: Without sub-base
(Note) A gasket & two mounting screws
D25 : 2-position, double solenoid
come with valve.
(A) (B) Connector position
42 P: S:

513 (With indicator light (Without indicator light
(R1) (P) (R2) and surge suppressor) and surge suppressor)

D35 : 3-position, closed center Voltage
1 : DC24V
(A) (B)
42 *: Made to order

513 Parker Hannifin Corporation
(R1) (P) (R2) Pneumatic Division

E35 : 3-position, exhaust center 40

(A) (B)
42

513
(R1) (P) (R2)

O35 : 3-position, pressure center

(A) (B)
42

513
(R1) (P) (R2)

Special specifications
No mark : Standard(Internal pilot)

X : * External pilot

(Note) External pilot valve is available only
when it is mounted on MFX.

ADEX VALVE

A05P, A05R Series

Ordering Instruction A05R M5

Manifold for A05R Series

MFU 7

Type of manifold Size of A and B ports
MCU : Common SUP, Common EXH M5 : M5
C4 : * With push-in fitting for φ 4
Ports 2 & 4 on valve body
C6 : * With push-in fitting for φ 6

Number of stations Mountable solenoid valve series
2 2 station A05R

20 20 station
…
…

Mountable solenoid valve For details refer to Pages 32 34.

A05R S25 1 P M5 E

Function For mounting on manifold
S25 : 2-position, single solenoid MF : For mounting on manifold
(Note) A gasket & two mounting
(A) (B)
42 screws come with valve.

513 Wiring
(R1) (P) (R2) No mark: Without connector

D25 : 2-position, double solenoid E : Connector with lead wire
(Length : 500mm)
(A) (B)
42 Size of ports 2 and 4
M5 : M5
513 C4 : * With push-in fitting for φ 4
(R1) (P) (R2) C6 : * With push-in fitting for φ 6

D35 : 3-position, closed center Connector position
P: S:
(A) (B)
42 (With indicator light (Without indicator light
and surge suppressor) and surge suppressor)
513
(R1) (P) (R2)

E35 : 3-position, exhaust center

(A) (B)
42

513
(R1) (P) (R2)

O35 : 3-position, pressure center

(A) (B)
42

513
(R1) (P) (R2)

Voltage
1 : DC24V

* : Made to order

Parker Hannifin Corporation
Pneumatic Division

41

ADEX VALVE

A05P, A05R Series

Optional Accessories and Spare parts

Connector with lead wire AB plate
A05P DC CL5 A05R AB M5

Lead wire length Port size
5 : 500mm M5 : M5
10 : *1000mm C4 : * With push-in fitting for φ 4
Voltage C6 : * With push-in fitting for φ 6
DC : For DC
Mounting Mounting
Type screw screw
P : For PR type
AB plate AB plate
For PR type DC (Tapped hole (With push-
( ) Black type) in fitting)
Plate gasket
( ) Red Plate gasket

(Note) For common use with PR type of A05 and A12 (Note) Gasket & mounting screws are supplied
For common use with A05R

Locking cover Blank plate For A05R
A05P LA
For A05P A05R BP
Color
A : Orange A05P BP Mounting
screw
(Note) For common use with all A05 and A12 Mounting Blank plate
screw
Tag for solenoid valve Blank plate Manifold
A 0 5 P N (Pack of 10) gasket
Base
Tag gasket

Solenoid valve Manifold gasket
A05R G
(Note) For common use with sub-base mountig type of A05
and A12 Content of kit
SG : Gasket & mounting screws
Base gasket G : Gasket only(Pack of 10)
A05PX G S : Mounting screw only (Pack of 20)

Content of kit Mounting screw
SG : Gasket & mounting screws Manifold gasket
G : Gasket only(Pack of 10)
S : Mounting screw only (Pack of 20) * : Made to order

Special specifications
No mark : Standard

X : * For external pilot(With port X)

Mounting screw

Base gasket

Parker Hannifin Corporation
Pneumatic Division

42

ADEX VALVE (Unit : mm)

A05P, A05R Seriesφ 9.4

Dimensions A05PS25 A05PD25
A05PD35, A05PE35, A05PO35
MFC□-A05P-M5 C4, C6 50 6
Blank plate A05P-BP
5.4
42 58 R1 R2 4.7 11.3
3-Rc1/8(Both side)26 50 22.7
(Port 1,3,5)10 24
49.5
9.5
12.5(7.3 : For C4) 4-φ 4.5
13(8.4 : For C6) (Mounting hole)

6
6

4 P=10.5n+9.5 (4)

L=10.5n+17.5

64.6

29.5 A 36.5
21
6 B

1.4 4.4 2n-M5
14 10.5 (Push-in fitting for 2n- φ 4 : C4)
(Push-in fitting for 2n- φ 6 : C6)

(Port 2 & 4)

Parker Hannifin Corporation
Pneumatic Division

43

ADEX VALVE (Unit : mm)

A05P, A05R Series

DMimFCe□ns-Aio0n5Ps-M5 C4, C6 -B

2n-M5 10.5 14
(Push-in fitting for 2n-φ 4 : C4) 4.4 1.4
(Push-in fitting for 2n-φ 6 : C6)
(Port 2 & 4)

64.6 2
39.5 4
34.5
With locking cover 29.5
21
5.4 6

11.3
36.5
4-φ 4.5
φ 9.4 (Mounting hole)
88
(7.3 : For C4) 50 6 (4) P=10.5n+9.5 4
(8.4 : For C6) L=10.5n+17.5
A05PS25

Blank plate A05P-BP

57.5 24 31 5
47.5 8
31.5
15.5 34.8
57.5

9.5

12.5 3-Rc1/8 (Both side)
13 (Port 1,3,5)

Parker Hannifin Corporation
Pneumatic Division

44

ADEX VALVE (Unit : mm)

A05P, A05R Series

DMimFSe□ns-Aio0n5Ps-01, MFX□-A05P-01 C4, C6

With locking cover

5.4

φ 9.4

A05PS25(For MFS) A05PS25(For MFS)
A05PS25X(For MFX) A05PS25X(For MFX)

M5(Both side) 50 6 A05PD35,A05PE35,A05PO35(For MFS)
(Port X for MFX) A05PD35X,A05PE35X,A05PO35X(For MFX)

3-Rc1/8 (Both side) Blank plate A05P-BP
(Port 1,3,5)

5 X 1 3Y 11.3

49.5 57
47.5
33.5 58 4.7 30.2
17.5 50

24

(3.6 : For MFX-C4) 11.5 M5(Both side) 4-φ 4.5
(8.4 : For MFX-C6) 14.5 (Port Y for MFX) (Mounting hole)
P=12.5n+7.5
27.5 6 (P=10.5n+9.5
6 4 : For MFX-C4,C6) (4)
L=12.5n+15.5
(L=10.5n+17.5
: For MFX-C4,C6)

67.1 4 24
32 2 39
22

7.5 2n-Rc 1/8

(Push-in fitting for 2n-φ 4 : MFX-C4)
1.4 4.4 (Push-in fitting for 2n-φ 6 : MFX-C6)

12.5 (Port 2 & 4)
14 (10.5 : For MFX-C4,C6)

Parker Hannifin Corporation
Pneumatic Division

45

ADEX VALVE (Unit : mm)

A05P, A05R Series 2n-Rc 1/8 12.5 14
(Port 2 & 4) 4.4 1.4
DMimFSe□ns-Aio0n5Ps-01-B
67.1 4
With locking cover 42 2
37
5.4 32
22
7.5
39

2-φ 4.5
(Mounting hole)

88

(4) P=12.5n+7.5 4

φ 9.4 L=12.5n+15.5

A05PS25

50 6 Blank plate A05P-BP

65 24 24
47.5 315
31.5 8
15.5 34.8

65

11.5 3-Rc1/8 (Both side)
14.5 (Port 1,3,5)

Parker Hannifin Corporation
Pneumatic Division

46

ADEX VALVE (Unit : mm)

A05P, A05R Series

DMimFUe□ns-Aio0n5Rs-M5 C4, C6

5.4

φ 9.4

A05RS25 A05RD25
A05RD35,A05RE35,A05RO35
3-Rc1/8(Both side) 50 6
(Port 1,3,5) 2m-M5
(Push-in fitting for 2n- φ 4 : C4)
(Push-in fitting for 2n- φ 6 : C6)
(Port 2 & 4)
Blank plate A05R-BP

16 16 24 5.1 5.1 513 88
23.5

47

9.5 6 58 6 50 4- φ 4.5
15.5 (Mounting hole)

52

(62.7 : For C4)
(63.5 : For C6)

4 P=10.5n+9.5 (4)

L=10.5n+17.5

59.1
24

31

14 10.5

Parker Hannifin Corporation
Pneumatic Division

47

ADEX VALVE

Multipin connector type manifold

MC A 0 5 P
Bar type R

MCC□ A05P Common SUP, Common EXH
Ports 2 & 4 on side
Compact type

MCS□ A05P Common SUP, Common EXH
Ports 2 & 4 on side

MCX□ A05P Common SUP, Common EXH
Common external pilot
Ports 2 & 4 on side

MCU□ A05R Common SUP, Common EXH
Ports 2 & 4 on valve body

Manifold Specifications For A05P Series MCX□ A05P For A05R Series

MCC□ A05P MCS□ A05P MCU□ A05R

Type of manifold Common SUP, Common EXH Common SUP, Common EXH Common SUP, Common EXH Common SUP, Common EXH
Pilot valve captured exhaust Pilot valve captured exhaust Common external pilot Pilot valve captured exhaust
Ports 2 & 4 on side Ports 2 & 4 on side Pilot valve captured exhaust Ports 2 & 4 on valve body
Compact type Ports 2 & 4 on side

Ports 1, 3, 5 Rc 1/8 Rc 1/8 Rc 1/8 Rc 1/8
M5, C4, C6 Rc 1/8 Rc1/8, C4, C6 M5, C4, C6
Port size Ports 2, 4
Port Y A05PS25 M5 A05RS25
A05PD25 M5 A05RD25
Port X A05PD35 2 12 A05RD35
A05PE35 Direct mount A05RE35
Number of stations A05PO35 A05RO35

Mounting

Mountable solenoid valve A05PS25 A05PS25X
A05PD25 A05PD25X
A05PD35 A05PD35X
A05PE35 A05PE35X
A05PO35 A05PO35X

Blank plate A05PG-BP A05RG-BP

Wiring

When doing wiring work, be sure to turn off power beforehand.
For wiring instructions, refer to Pages 23 and 24.

Parker Hannifin Corporation
Pneumatic Division

48

ADEX VALVE

A05P, A05R Series

Ordering Instructions

Manifold for A05P Series A05P 01 ML P

MCC 7

Type of manifold Ootion 2
DMF : With Manifold drive unit
MCC : Common SUP, Common EXH
Ports 2 & 4 on side No mark : Without Manifold drive unit
Compact type (Note) Manifold drive unit can be

MCS : Common SUP, Common EXH mounted for ML type only.
Ports 2 & 4 on side
Polarity
MCX : Common SUP, Common EXH P : NPN type
Common external pilot M :* PNP type
Ports 2 & 4 on side

Connector specification
Number of stations ML : Flat cable connector

2 2 station DL : D sub-connector

… Size of Ports 2 and 4
…

12 12 station M5 : M5 Type M5 01 C4 C6

Mountable solenoid valve series 01 : Rc1/8 MCC ○ ○ ○ ○
A05P MCS ○ ○ ○
C4 : * With push-in fitting MCX

for φ 4

C6 :* With push-in fitting

for φ 6 (Note) When using G, NPT, NPTF threads,

Mountable solenoid valve For details refer to Pages 26 28. consult KURODA Pneumatics Ltd.

A05P S25 1 P PS

Function Wiring
S25 : 2-position, single solenoid No mark: Without connector

(A) (B) PS : With connector for collective wiring
42 (For single solenoid )

513 PD : With connector for collective wiring
(R1) (P) (R2) (For double solenoid )

D25 : 2-position, double solenoid (Note) For minus common (PNP), order a
connector in addition
(A) (B)
42 Port size
No mark: Without sub-base
513 (Note) A gasket & two mounting screws
(R1) (P) (R2)
come with valve.
D35 : 3-position, closed center
Connector position
(A) (B) P: S:
42
(With indicator light (Without indicator light
513 and surge suppressor) and surge suppressor)
(R1) (P) (R2)
Voltage
E35 : 3-position, exhaust center 1 : DC24V

(A) (B) * : Made to order
42

513
(R1) (P) (R2)

O35 : 3-position, pressure center

(A) (B)
42

513
(R1) (P) (R2)

Special specifications
No mark : Standard(Internal pilot )

X : * External pilot

(Note) External pilot valve is available only
when it is mounted on MCX.

Parker Hannifin Corporation
Pneumatic Division

49

ADEX VALVE

A05P, A05R Series

Ordering Instructions A05R 01 ML P

Manifold for A05R Series

MCU 7

Type of manifold Option 2
MCU : Common SUP, Common EXH DMF : With Manifold drive unit

Ports 2 & 4 on valve body No mark : Without Manifold

drive unit
(Note) Manifold drive unit can be

mounted for ML type only.

…Number of stations Polarity
…2 2 station P : NPN type
M : * PNP type
12 12 station
Connector specification
Mountable solenoid valve series ML : Flat cable connector
A05R DL : D sub-connector

Size of ports 2 and 4
M5 : M5

C4 : * With push-in fitting for φ 4

C6 : * With push-in fitting for φ 6

Mountable solenoid valve For details refer to Pages 32 34.

A05R S25 1 P PS

Function For mounting on manifold
S25 : 2-position, single solenoid MF : For mounting on manifold
(Note) A gasket & two mounting
(A) (B)
42 screws come with valve.
Wiring
513 No mark: Without connector
(R1) (P) (R2)
PS : With connector for collective wiring
D25 : 2-position, double solenoid (For single solenoid)

(A) (B) PD : With connector for collective wiring
42 (For double solenoid )

513 (Note) For minus common (PNP), order a
(R1) (P) (R2) connector in addition

D35 : 3-position, closed center Size of ports 2 and 4
M5 : M5
(A) (B) C4 : * With push-in fitting for φ 4
42 C6 : * With push-in fitting for φ 6

513 Connector position
(R1) (P) (R2) P: S:

E35 : 3-position, exhaust center (With indicator light (Without indicator light
and surge suppressor) and surge suppressor)
(A) (B)
42

513
(R1) (P) (R2)

O35 : 3-position, pressure center

(A) (B)
42

513
(R1) (P) (R2)

Voltage
1 : DC24V

* : Made to order

Parker Hannifin Corporation
Pneumatic Division

50