Wedge Sockets
FEATURES
• Wedge socket terminations have an efficiency rating of 80% based on the
catalog strength of XXIP wire rope.
• Pin diameter and jaw opening allows wedge and socket to be used in conjunction
with closed swage and spelter sockets.
• Secures the tail or “dead end” of the wire rope to the wedge, thus eliminates
loss or “punch out” of the wedge.
• Incorporates Crosby’s patented QUIC-CHECK® “Go” and “No-Go” feature
cast into the wedge. The proper size rope is determined when the following
criteria are met:
• 1) The wire rope should pass thru the “Go” hole in the wedge.
• 2) The wire rope should NOT pass thru the “No-Go” hole in the wedge.
• Utilizes standard Crosby Red-U-Bolt® wire rope clip.
S-421T Wedge Sockets Assembly
Includes Socket, Wedge, Pin and Wire
Rope Clip
Wire Rope S-421T SSt-o4c2k1 TNWo. Optional
Dia. Stock Wedge Only G-4082
(in.) Bolt, Nut & Cotter
3/8 No. 1035555 1092227
1/2 1035564 1092236
5/8 1035000 1035573 1092254
3/4 1035009 1035582 1092281
7/8 1035018 1035591 1092307
1 1035027 1035600 1092325
1-1/8 1035036 1035609 1092343
1-1/4 1035045 1035618 1092372
1035054
1035063
DIMENSIONS (in.)
Wire Rope Dia (in.) S-421T Stock No. A B C D G H J K L P R S T U V
3/8 1035000 5.69 2.72 81 .81 1.38 3.06 7.80 1.88 .88 1.56 .44 2.13 .44 1.25 1.38
1.00 1.62 3.76 8.91 1.26 1.06 1.94 .50 2.56 .53 1.75 1.88
1/2 1035009 6.88 3.47 1.00 1.19 2.12 4.47 10.75 1.99 1.22 2.25 .56 3.25 .69 2.00 2.19
1.38 2.44 5.28 12.36 2.41 1.40 2.63 .66 3.63 .78 2.34 2.56
5/8 1035018 8.25 4.30 1.25 1.63 2.69 6.16 14.37 2.48 1.67 3.13 .75 4.31 .88 2.69 2.94
2.00 2.94 6.96 16.29 3.04 2.00 3.75 .88 4.70 1.03 2.88 3.28
3/4 1035027 9.88 5.12 1.50 2.25 3.31 7.62 18.34 2.56 2.25 4.25 1.00 5.44 1.10 3.25 3.56
2.50 3.56 9.39 20.48 2.94 2.34 4.50 1.06 6.13 1.19 4.62 4.94
7/8 1035036 11.25 5.85 1.75
1 1035045 12.81 6.32 2.00
1-1/8 1035054 14.38 6.92 2.25
1-1/4 1035063 16.34 8.73 2.62
NOTE: For intermediate wire rope sizes, use next larger size socket.
Minimum breaking force of standard wire rope used on Superior’s pneumatic tuggers
6 x 19 IWRC (XIP) Strength and Weights Chart Minimum
Breaking Force
Diameter Weight Minimum Diameter Weight Minimum Diameter Weight
(in.) (lb/ft) Breaking Force (in.) (lb/ft) Breaking Force (in.) (lb/ft) (lbs.)
1/4 0.116 (lbs.) 5/8 0.72 (lbs.) 1-3/8 3.50 192,000
5/16 0.18 3/4 1.04 1-1/2 4.16 228,000
3/8 0.26 6,800 7/8 1.42 41,200 1-5/8 4.88 264,400
7/16 0.35 10,540 1.85 58,800 1-3/4 5.67 306,000
1/2 0.46 15,540 1 2.34 79,600 1-7/8 6.50 348,000
9/16 0.59 20,400 1-1/8 2.89 103,400 7.39 396,000
26,600 1-1/4 130,000 2
33,600 159,800
Overhaul Ball Assembly Split Overhaul Balls
UB500 Working Weight UB500 Working Weight • Attaches easily to Wire Rope.
“E” Load Limit Each “E” Load Limit Each
(lbs.) (lbs.) SPECIFICATIONS
Eye Hook (tons) Eye Hook (tons)
Item # 58 Item # 216 Item # Wire Rope Weight Ball
4 102 12 258 Sizes Each Dia.
1036000* 4 162 1036144* 12 365 (in.) (lbs.) (in.)
1036009* 4 201 1036153* 12 403
1036027* 4 109 1036171* 12 718 5.06
1036036* 7 170 1036180* 12 298 5.38
1036045* 7 210 1036189* 15 456 7.12
1036054* 7 321 1036198* 15 753 9.19
1036072* 7 216 1036207* 15 1311
1036081* 10 260 1036216* 15 298
1036090* 10 365 1036225* 20 456
1036099* 10 403 1036234* 20 753
1036117* 10 718 1036243* 20 1311
1036126* 10 1036252* 20 533
1036135* 1036261* 25 865
1036270* 25 1421
* Utilizes Crosby “N” style hooks with integrated latch. Replacement latch 1036279* 25 865 2003822 1/4 - 5/16 15
kit is S-4055 latch will not fit. Standard Crosby S-5 Thrust style swivels can 1036288* 30 1421 2003830 3/8 20
not be used with UB500 Overhaul Balls For replacement swivels, contact 1036297* 30 2003831 50
Our Customer Service. 1036306* 2003832 1/2 - 5/8 100
5/8 - 3/4 - 7/8
877.446.4352 www.superiortoolrental.com www.midlandtool.com 101
Shackles
102
Shackles
PURCHASE or RENT
Screw Pin Anchor Shackles
FEATURES
• G-209 is Galvanized
• S-209 is Self Colored
SPECIFICATIONS
Nominal Working Item # Weight A B C DIMENSIONS (in.) L M Tolerance +/–
Size (LLtooimnaidst) G-209 S-209 Each DE F G H
(in.) (lbs.) PC A
3/16 1/3 1018357 - .06 .38 .25 .88 .19 .60 .56 .98 1.47 .16 1.14 .19 .06 .06
1/4 1/2 1018375 1018384 .10 .47 .31 1.13 .25 .78 .61 1.28 1.84 .19 1.43 .25 .06 .06
5/16 3/4 1018393 1018400 .18 .53 .38 1.22 .31 .84 .75 1.47 2.09 .22 1.71 .31 .06 .06
3/8 1 1018419 1018428 .31 .66 .44 1.44 .38 1.03 .91 1.78 2.49 .25 2.02 .38 .13 .06
7/16 1-1/2 1018437 1018446 .38 .75 .50 1.69 .44 1.16 1.06 2.03 2.91 .31 2.37 .44 .13 .06
1/2 2 1018455 1018464 .72 .81 .63 1.88 .50 1.31 1.19 2.31 3.28 .38 2.69 .50 .13 .06
5/8 3-1/4 1018473 1018482 1.37 1.06 .75 2.38 .63 1.69 1.50 2.94 4.19 .44 3.34 .69 .13 .06
3/4 4-3/4 1018491 1018507 2.35 1.25 .88 2.81 .75 2.00 1.81 3.50 4.97 .50 3.97 .81 .25 .06
7/8 6-1/2 1018516 1018525 3.62 1.44 1.00 3.31 .88 2.28 2.09 4.03 5.83 .50 4.50 .97 .25 .06
1 8-1/2 1018534 1018543 5.03 1.69 1.13 3.75 1.00 2.69 2.38 4.69 6.56 .56 5.13 1.06 .25 .06
1-1/8 9-1/2 1018552 1018561 7.41 1.81 1.25 4.25 1.16 2.91 2.69 5.16 7.47 .63 5.71 1.25 .25 .06
1-1/4 12 1018570 1018589 9.50 2.03 1.38 4.69 1.29 3.25 3.00 5.75 8.25 .69 6.25 1.38 .25 .06
1-3/8 13-1/2 1018598 1018605 13.53 2.25 1.50 5.25 1.42 3.63 3.31 6.38 9.16 .75 6.83 1.50 .25 .13
1-1/2 17 1018614 1018623 17.20 2.38 1.63 5.75 1.54 3.88 3.63 6.88 10.00 .81 7.33 1.62 .25 .13
1-3/4 25 1018632 1018641 27.78 2.88 2.00 7.00 1.84 5.00 4.19 8.86 12.34 1.00 9.06 2.25 .25 .13
2 35 1018650 1018669 45.00 3.25 2.25 7.75 2.08 5.75 4.81 9.97 13.68 1.22 10.35 2.40 .25 .13
2-1/2 55 1018678 1018687 85.75 4.13 2.75 10.50 2.71 7.25 5.69 12.87 17.84 1.38 13.00 3.13 .25 .25
Bolt Type Shackles
FEATURES
• G-2130 is Galvanized
• S-2130 is Self Colored
SPECIFICATIONS
NoSmizienal Working Item # Weight A B C DIMENSIONS (in.) L Tolerance +/–
(in.) (LLtooimnaidst) G-2130 S-2130 Each DEF H
(lbs.) NCA
3/16 1/3 1019464 - .06 .38 .25 .88 .19 .60 .56 1.47 .98 .19 .06 .06
1/4 1/2 1019466 - .11 .47 .31 1.13 .25 .78 .61 1.84 1.28 .25 .06 .06
5/16 3/4 1019468 - .22 .53 .38 1.22 .31 .84 .75 2.09 1.47 .31 .06 .06
3/8 1 1019470 - .33 .66 .44 1.44 .38 1.03 .91 2.49 1.78 .38 .13 .06
7/16 1-1/2 1019471 - .49 .75 .50 1.69 .44 1.16 1.06 2.91 2.03 .44 .13 .06
1/2 2 1019472 1019481 .79 .81 .64 1.88 .50 1.31 1.19 3.28 2.31 .50 .13 .06
5/8 3-1/4 1019490 1019506 1.68 1.06 .77 2.38 .63 1.69 1.50 4.19 2.94 .69 .13 .06
3/4 4-3/4 1019515 1019524 2.72 1.25 .89 2.81 .75 2.00 1.81 4.97 3.50 .81 .25 .06
7/8 6-1/2 1019533 1019542 3.95 1.44 1.02 3.31 .88 2.28 2.09 5.83 4.03 .97 .25 .06
1 8-1/2 1019551 1019560 5.66 1.69 1.15 3.75 1.00 2.69 2.38 6.56 4.69 1.06 .25 .06
1-1/8 9-1/2 1019579 1019588 8.27 1.81 1.25 4.25 1.13 2.91 2.69 7.47 5.16 1.25 .25 .06
1-1/4 12 1019597 1019604 11.71 2.03 1.40 4.69 1.29 3.25 3.00 8.25 5.75 1.38 .25 .06
1-3/8 13-1/2 1019613 1019622 15.83 2.25 1.53 5.25 1.42 3.63 3.31 9.16 6.38 1.50 .25 .13
1-1/2 17 1019631 1019640 19.00 2.38 1.66 5.75 1.53 3.88 3.63 10.00 6.88 1.62 .25 .13
1-3/4 25 1019659 1019668 33.91 2.88 2.04 7.00 1.84 5.00 4.19 12.34 8.80 2.25 .25 .13
2 35 1019677 1019686 52.25 3.25 2.30 7.75 2.08 5.75 4.81 13.68 10.15 2.40 .25 .13
2-1/2 55 1019695 1019702 98.25 4.13 2.80 10.50 2.71 7.25 5.69 17.90 12.75 3.13 .25 .25
3 85 1019711 - 154.00 5.00 3.30 13.00 3.12 7.88 6.50 21.50 14.62 3.62 .25 .25
3-1/2 120 1019739 - 265.00 5.25 3.76 14.63 3.62 9.00 8.00 24.88 17.02 4.38 .25 .25
4 150 1019757 338.00 5.50 4.26 14.50 4.00 10.00 9.00 25.68 18.00 4.56 .25 .25
877.446.4352 www.superiortoolrental.com www.midlandtool.com 103
Shackles
PURCHASE or RENT
Alloy Screw Pin Shackles
FEATURES
• G-209 is Galvanized
SPECIFICATIONS
Nominal W(tLLoooirmnkasiidnt)*g Item # Weight DIMENSIONS (in.) Tolerance +/–
S(iinz.e) G-209A Each
(lbs.) A B CD E F G H L MP C A
3/8 2 1017450 .31 .66 .44 1.44 .38 1.03 .91 1.78 2.49 .25 2.03 .38 .13 .06
7-1/6 2-2/3 1017472 .38 .75 .50 1.69 .44 1.16 1.06 2.03 2.91 .31 2.38 .44 .13 .06
1/2 3-1/3 1017494 .63 .81 .63 1.88 .50 1.31 1.19 2.31 3.28 .38 2.69 .50 .13 .06
5/8 5 1017516 1.38 1.06 .75 2.38 .63 1.69 1.50 2.94 4.19 .44 3.34 .69 .13 .06
3/4 7 1017538 2.35 1.25 .88 2.81 .75 2.00 1.81 3.50 4.97 .50 3.97 .81 .25 .06
7/8 9-1/2 1017560 3.61 1.44 1.00 3.31 .88 2.28 2.09 4.03 5.83 .50 4.50 .97 .25 .06
1 12-1/2 1017582 5.32 1.69 1.13 3.75 1.00 2.69 2.38 4.69 6.56 .56 5.07 1.06 .25 .06
1-1/8 15 1017604 7.25 1.81 1.25 4.25 1.16 2.91 2.69 5.16 7.47 .63 5.59 1.25 .25 .06
1-1/4 18 1017626 9.88 2.03 1.38 4.69 1.29 3.25 3.00 5.75 8.25 .69 6.16 1.38 .25 .06
1-3/8 21 1017648 13.25 2.25 1.50 5.25 1.42 3.63 3.31 6.38 9.16 .75 6.84 1.50 .25 .13
*Maximum Proof Load is 2 times the Working Load Limit (metric tons) and 2.2 times the Working Load Limit (short
tons). Minimum Ultimate Strength is 4.5 times the Working Load Limit for metric tons, and 5 times the Working Load
Limit for short tons.
Alloy Bolt Type Anchor Shackles
FEATURES
• G-2140 is Galvanized
• S-2140 is Self Colored
Alloy Bolt Type Anchor Shackles
Nominal Working Item # Weight A B C D DIMENSIONS (in.) J K Tolerance +/–
Size Load G-2140 S-2140 Each EFG H
(in.) Limit (lbs.) LA E
(tons)*
1-1/2 30 1021110 1021129 18.8 2.38 3.62 1.62 1.63 5.75 1.39 6.88 7.73 10.00 3.88 1.53 .13 .25
1-3/4 40 1021138 1021147 33.8 2.88 4.19 2.25 2.00 7.00 1.75 8.81 9.33 12.34 5.00 1.84 .13 .25
2 55 1021156 1021165 49.9 3.25 4.81 2.40 2.25 7.75 2.00 10.16 10.41 13.68 5.75 2.08 .13 .25
2-1/2 85 1021174 1021183 103 4.12 5.81 3.12 2.75 10.50 2.62 12.75 13.58 17.90 7.25 2.71 .25 .25
3 120 1021192 - 162 5.00 6.50 3.63 3.25 13.00 3.00 14.62 15.13 21.50 7.88 3.12 .25 .25
3-1/2 •150 1021218 - 268 5.25 8.00 4.38 3.75 14.63 3.75 17.02 17.62 24.88 9.00 3.62 .25 .25
4 •175 1021236 - 332 5.50 9.00 4.56 4.25 14.50 4.00 18.00 20.37 25.68 10.00 4.00 .25 .25
4-3/4** •200 1021422 - 452 7.25 10.50 5.00 4.75 15.19 4.58 20.84 23.11 27.81 11.00 4.75 .25 .25
5 ** •250 1021442 - 594 8.50 12.00 5.63 5.00 18.50 4.48 23.63 24.28 32.63 13.00 5.00 .25 .25
6 •300 1021460 - 791 8.38 13.00 6.06 6.00 18.72 4.89 24.76 25.45 34.28 13.00 5.88 .25 .25
7 ** •400 1021478 - 1200 8.25 14.00 7.25 7.00 22.50 6.50 26.00 28.68 40.25 13.00 6.00 .25 .25
*Note: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Load is 4 times the Working
Load Limit on 200 thru 400 metric Tons. For sizes 30 thru 175 metric Tons, Minimum Ultimate Load is 5.4 times the
Working Load Limit. **Cast Alloy Steel.
• Furnished with round head bolts with an eyebolt for handling.
104
Shackles
PURCHASE or RENT
Bow Shackles with Screw Collar Pin
FEATURES
• Hot Dipped Galvanized
SPECIFICATIONS DIMENSIONS (in.)
W(LLtoooirmnkasiidnt)g Diameter Diameter Diameter Width Width Length Width Length Length Width Weight
Bow Pin Eye Eye Inside Inside Bow Bolt Each
0.33 A B C H I
0.5 3/16 1/4 1/2 DE F G 1-13/32 J (lbs)
0.75 1/4 5/16 21/32 5/8 1-29/32 1-5/32
1 5/16 3/8 25/32 3/16 3/8 7/8 25/32 2-7/32 1-1/2 1-1/32 0.05
1.5 3/8 7/16 7/8 7/8 1-27/32
2 7/16 1/2 9/32 15/32 1-5/32 1-1/32 2-1/2 2-1/8 1-11/32 0.11
3.25 1/2 5/8 1-1/32 1-5/32 2-29/32 2-11/32
4.5 5/8 3/4 1-11/32 11/32 17/32 1-1/4 1-1/4 2-7/8 1-9/16 0.22
6.5 3/4 7/8 1-9/16 1-11/16 3-1/2 3-1/2
8.5 7/8 1 1-13/16 13/32 21/32 1-7/16 2 4-11/32 4-1/16 1-13/16 0.3
9.5 1 1-1/8 2-1/16 2-9/32 5-3/32 4-11/16
12 1-1/8 1-1/4 2-5/16 7/16 3/4 1-11/16 2-11/16 5-21/32 5-13/32 2 0.42
13.5 1-1/4 1-3/8 2-19/32 2-15/16 6-15/32 6-1/32
17 1-3/8 1-1/2 2-27/32 1/2 7/8 2 3-9/32 7-9/32 6-11/16 2-9/32 0.79
25 1-1/2 1-5/8 3-5/32 3-5/8 7-29/32 7-5/16
35 1-3/4 2 3-15/32 5/8 1-1/16 2-17/32 3-29/32 8-15/16 2-15/16 1.38
42.5 2 2-1/4 4-1/16 4-31/32 9-13/16 8
55 2-1/4 3/4 1-7/32 3 5-7/16 11-13/16 9-9/16 3-1/2 2.22
2-1/2 2-9/16 4-3/8 6-5/16 13-1/32 10-23/32
2-3/4 5-1/8 7/8 1-13/32 3-9/32 7-3/32 14-27/32 12-7/32 4-1/32 3.31
5-23/32 17-1/16 13-17/32
31/32 1-11/16 3-3/4 4-21/32 4.86
1-3/32 1-27/32 4-1/4 5-5/32 6.97
1-1/4 2 4-17/32 5-25/32 9.49
1-3/8 2-1/4 5-1/4 6-3/8 12.24
1-1/2 2-3/8 5-3/4 6-7/8 16.37
1-25/32 2-29/32 7 8-1/2 28.31
1-31/32 3-9/32 7-3/4 9-3/8 40.01
2-1/4 3-3/4 8-3/4 10-25/32 57.96
2-9/16 4-1/8 10-1/4 12-7/32 82.89
Bow Shackles with Safety Bolt
FEATURES
• Hot Dipped Galvanized
SPECIFICATIONS
Working DIMENSIONS (in.) Weight
Each
Load Diameter Diameter Diameter Width Width Length Width Length Length Width Thickness (lbs.)
Limit Bow Pin Eye Eye Inside Inside Bow Bolt J Nut
H K
(tons) A B C D EF G 1-29/32 I
9/32 2-7/32 1-21/32
0.5 1/4 5/16 21/32 11/32 15/32 1-5/32 25/32 2-1/2 1-31/32 1-11/32 5/32 0.13
13/32 2-29/32 2-3/8
0.75 5/16 3/8 25/32 7/16 17/32 1-1/4 7/8 3-1/2 2-5/8 1-9/16 3/16 0.25
1/2 4-11/32 3-7/32
1 3/8 7/16 7/8 5/8 21/32 1-7/16 1-1/32 5-3/32 3-27/32 1-13/16 5/16 0.34
3/4 5-21/32 4-1/2
1.5 7/16 1/2 1-1/32 7/8 3/4 1-11/16 1-5/32 6-15/32 5-1/8 2 7/16 0.48
31/32 7-9/32 5-29/32
2 1/2 5/8 1-11/32 1-3/32 7/8 2 1-1/4 7-29/32 6-17/32 2-9/32 1/2 0.92
1-1/4 8-15/16
3.25 5/8 3/4 1-9/16 1-3/8 1-1/16 2-17/32 1-11/16 9-13/16 7 2-15/16 21/32 1.62
1-1/2 11-13/16 7-3/4
4.75 3/4 7/8 1-13/16 1-25/32 1-7/32 3 2 13-1/32 7-15/16 3-1/2 3/4 2.59
1-31/32 14-27/32 9-13/16
6.5 7/8 1 2-1/16 2-1/4 1-13/32 3-9/32 2-9/32 17-1/16 10-19/32 4-1/32 7/8 3.9
2-9/16 20-3/4 11-27/32
8.5 1 1-1/8 2-5/16 2-7/8 1-11/16 3-3/4 2-11/16 4-21/32 31/32 5.69
13
9.5 1-1/8 1-1/4 2-19/32 1-27/32 4-1/4 2-15/16 14-31/32 5-5/32 1-1/16 8.06
12 1-1/4 1-3/8 2-27/32 2 4-17/32 3-9/32 5-25/32 1-3/16 10.81
13.5 1-3/8 1-1/2 3-5/32 2-1/4 5-1/4 3-5/8 6-3/8 1-5/8 14.42
17 1-1/2 1-5/8 3-15/32 2-3/8 5-3/4 3-29/32 6-7/8 3/4 18.06
25 1-3/4 2 4-1/16 2-29/32 7 4-31/32 8-1/2 29/32 31.34
35 2 2-1/4 4-3/8 3-9/32 7-3/4 5-7/16 9-3/8 1-1/32 43.77
42.5 2-1/4 2-9/16 5-1/8 3-3/4 8-3/4 6-5/16 10-23/32 1-5/32 62.46
55 2-1/2 2-3/4 5-23/32 4-1/8 10-1/4 7-3/32 12-7/32 1-1/4 87.27
85 3 3-1/4 6-3/8 5 12-15/16 7-15/32 13-3/8 1-17/32 136.69
877.446.4352 www.superiortoolrental.com www.midlandtool.com 105
Shackles
PURCHASE or RENT
Alloy Bow Shackles with Safety Bolt
FEATURES
• Hot Dipped Galvanized
Bow Shackles with Safety Bolt
Working DIMENSIONS (in.) Weight
Each
Load Diameter Diameter Diameter Width Width Length Width Length Length Width Thickness (lbs.)
Limit Bow Pin Eye Eye Inside Inside Bow Bolt Nut
(tons) A B C D I
EF G H JK
3-7/32
3.3 1/2 5/8 1-11/32 1/2 7/8 2 1-1/4 3-1/2 3-27/32 2-9/32 1/2 0.97
5 5/8 3/4 1-9/16 5/8 1-1/16 2-17/32 1-11/16 4-11/32 4-1/2 2-15/16 21/32 1.74
5-1/8
7 3/4 7/8 1-13/16 3/4 1-7/32 3 2 5-3/32 5-29/32 3-1/2 3/4 2.78
6-17/32
9.5 7/8 1 2-1/16 7/8 1-13/32 3-9/32 2-9/32 5-21/32 4-1/32 7/8 4.14
7
12.5 1 1-1/8 2-5/16 31/32 1-11/16 3-3/4 2-11/16 6-15/32 7-3/4 4-21/32 31/32 6.13
7-15/16
15 1-1/8 1-1/4 2-19/32 1-3/32 1-27/32 4-1/4 2-15/16 7-9/32 9-13/16 5-5/32 1-1/16 8.53
11-1/4
18 1-1/4 1-3/8 2-27/32 1-1/4 2 4-17/32 3-9/32 7-29/32 13-17/32 5-25/32 1-3/16 11.6
15-7/8
21 1-3/8 1-1/2 3-5/32 1-3/8 2-1/4 5-1/4 3-5/8 8-15/16 20-1/8 6-3/8 1-5/16 15.3
22-3/32
30 1-1/2 1-5/8 3-15/32 1-1/2 2-3/8 5-3/4 3-29/32 9-13/16 6-7/8 3/4 19.38
40 1-3/4 2 4-1/16 1-25/32 2-29/32 7 4-31/32 11-13/16 8-1/2 29/32 33.07
55 2 2-1/4 4-19/32 2-1/4 3-9/32 7-3/4 5-7/16 13-7/16 9-29/32 1-1/32 48.50
85 2-1/2 2-3/4 5-5/8 2-3/4 4-1/8 10-1/4 7-3/32 17-7/32 12-19/32 1-1/4 92.59
120 3 3-1/4 6-3/8 3-9/32 5 12-15/16 7-15/32 21-1/16 14-1/32 1-9/16 154.32
150* 3-3/4 3-3/4 8-3/16 3-19/32 5-25/32 15-3/4 9-3/8 25-15/32 16-27/32 1-31/32 246.92
175* 4 4-1/4 9-3/8 4-1/32 6-21/32 16-5/32 10-13/16 27-3/32 19-3/32 2-3/8 352.74
* = round headed bolt
106
Slings, Turnbuckles,
Ratchet Binders & Dynamometer
877.446.4352 www.superiortoolrental.com www.midlandtool.com 107
NSlyilnogns/Polyester
Sling to Load Eye & Eye Slings HEAVY DUTY (900 WEBBING)
Angle Efficiency
TYPE 3 - FLAT EYE
Rated Capacity in Pounds Inside Weight in Lbs.
Eye Size
Width Item # Ply Vertical Choker Basket
Laying
Flat
(in.) 5' base add/ft
1" 91EE2 2 3200 2600 6400 9 .68 .112
2" 92EE2 2 6400 5100 12800 9 1.30 .220
3" 93EE2 2 8900 7200 17800 12 2.16 .350
4" 94EE2 2 11500 9200 23000 12 2.45 .444
5" 95EE2 2 13600 10900 27200 15 3.28 .548
6" 96EE2 2 16300 13000 32600 15 3.78 .662
8" 98EE2 2 22000 17600 44000 18 5.47 .960
10" 910EE2 2 24000 19200 48000 18 7.05 1.190
12" 912EE2 2 26900 21500 53800 24 8.67 1.470
Endless Web Slings HEAVY DUTY (900 WEBBING)
Sling working load limits whether nylon, wire rope TYPE 5 - ENDLESS
or chain slings are rated with their respective
vertical, choker, and basket capacities. When Rated Capacity in Pounds Weight in Lbs.
selecting these slings, careful consideration must
be made for the proper sling to load horizontal Width Item # Ply Vertical Choker Basket
lifting angle. The greater angle to sling configuration
will result in a reduction of sling efficiency and a 5' base add/ft
loss of rated work load limits!
SEE ILLUSTRATION ABOVE: 1" 91EN2 2 6400 5100 12800 1.24 .22
(A) at a 90º sling to load angle the sling is at 1-3/4" 9175EN2 2 10000 8000 20000 1.73 .31
100% of the WLL.
2" 92EN2 2 12800 10200 25600 2.60 .44
(B) at a 60º sling to load angle a loss of 14%
efficiency occurs and the sling is capable 3" 93EN2 2 17500 14000 35000 4.06 .70
of lifting only 8,600 lbs.
4" 94EN2 2 23500 18000 47000 5.00 .88
(C) at a 45º sling to load angle a loss of 30%
efficiency occurs and the sling is capable 6" 96EN2 2 32500 26100 65000 7.50 1.29
of lifting only 7,000 lbs.
Viking ShieldTM (SEAMLESS)
(D) at a 30º sling to load angle the working
load limit is reduced by 50% and the
sling is capable of lifting only 5,000 lbs.
Load Angle Efficiency
Horizontal Efficiency Loss of
Lift Angle Rating Rating
90º 100% 0% Item # Sling Approx. Vertical Choker Basket Approx.
Color Diameter 5200 Weight
80º 98% 2% 10600 Per Feet
Inches 16800
70º 94% 6% 21200 .20
26400 .30
60º 86% 14% 33600 .46
42400 .54
50º 76% 24% 50000 .78
62000 .87
45º 70% 30% VRS1 Purple .60 2600 2080 1.12
VRS2 Green .80 5300 4240 1.51
40º 64% 36% VRS3 Yellow 1.00 8400 6720 2.06
VRS4 Tan 1.20 10600 8500
30º 50% 50% VRS5 Red 1.30 13200 10560
VRS6 White 1.40 16800 13440
VRS7 Blue 1.55 21200 17000
VRS8 Orange 1.75 25000 20000
VRS9 Orange 1.95 31000 24800
108
Nylon/PolSyelsintgesr
VikingTM (SEAMED) ! Observe Rated Capacity
WARNING!
Item # Sling Approx. Vertical Choker Basket Approx.
Color Diameter Weight Work load limits will be reduced when less than 90º
2080 5200 Per Feet from horizontal (See Efficiency Chart) Angles of less than
Inches 4240 10600 30º are not to be used. Inspect before use. Additional
6720 16800 requirements and safe operating practices are outlined
8500 21200 in current OSHA, Federal Register Part 29, 1910.184 and
10560 26400 ASME B30.9 c-2000. Death or injury can occur from
13440 33600 improper use or maintenance!
17000 42400
VR1 Purple .60 2600 20000 50000 .20
VR2 Green .80 5300 24800 62000 .30
VR3 Yellow 1.00 8400 32000 80000 .46
VR4 1.20 10600 42320 105800 .54
VR5 Tan 1.30 13200 52880 132200 .78
VR6 Red 1.40 16800 72000 180000 .87
VR7 Orange 1.55 21200 1.12
VR8 Blue 1.75 25000 1.51
VR9 Orange 1.95 31000 2.06
VR10 Orange 2.35 40000 2.86
VR11 Orange 3.15 52900 3.59
VR12 Orange 3.95 66100 4.58
VR13 Orange 4.80 90000 6.14
Orange
Eye & Eye Round Slings
RATED CAPACITY IN POUNDS
Item # Color Vertical Choker Basket Eye Approx. Weight
of Length Per Foot
Eyes (in.)
VEE1 Purple 2600 2100 5200 10 .26
VEE2 Green 5300 4200 10600 10 .37
VEE3 Yellow 8400 6700 16800 12 .52
VEE4 Tan 10600 8500 21200 12 .62
VEE5 Red 13200 10600 26400 14 .83
VEE6 Orange 16800 13400 33600 16 .98
VEE7 Blue 21200 17000 42400 16 1.50
Rough N’ Tough
RATED CAPACITY IN POUNDS
Item # Width Vertical Choker Basket Eye Weight in Lbs.
Length 8' base add/ft
(in.)
862RNT 2" 5000 4000 10000 10 1.6 .18
892RNT 2" 7000 6000 14000 10 1.9 .22
864RNT 4" 10000 8000 20000 12 3.2 .36
894RNT 4" 14000 11200 28000 12 3.8 .44
877.446.4352 www.superiortoolrental.com www.midlandtool.com 109
Wire Rope One Leg Eye & Eye Wire Rope Slings
Sling to Load Rope Eye Type 10 (6x26) Type 33 (7x7x19) Type 30 (6x26)
Angle Effifiency Diameter Size
(in.) “Tough-Lock™” Mechanical Sling “Cable-Flex™” Mechanical Sling RIggers Hand Splice
(in.)
(AXB) * RATED CAPACITY (TONS) * RATED CAPACITY (TONS) * RATED CAPACITY (TONS)
Vertical Choker Basket ** Vertical Choker Basket ** Vertical Choker Basket **
1/4 2x4 .65 .48 1.3 .5 .34 1 .49 .38 .99
3/8 4x8 1.4 1.1 2.9 1.1 .74 2.2 1.1 .85 2.1
1/2 4x8 2.5 1.9 5.1 1.9 1.3 3.7 1.8 1.5 3.7
5/8 5x10 3.9 2.9 7.8 2.8 1.9 5.5 2.8 2.3 5.6
3/4 6x12 5.6 4.1 11 4.1 2.8 8.1 3.9 3.3 7.8
7/8 7x14 7.6 5.6 15 5.4 3.7 11 5.2 4.5 10
1 8x16 9.8 7.2 20 6.9 4.7 14 6.7 5.9 13
1-1/8 9x18 12 9.1 24 8.3 5.8 17 -- -
1-1/4 10x20 15 11 30 9.9 7 20 -- -
1-3/8 11x22 18 13 36 - -- -- -
1-1/2 12x24 21 16 42 - -- -- -
*1 ton = 2000 lbs. ** Ratings based on a minimum D/d ratio of 25 (D =curvature around which the body is bent; d=diameter of wire rope)
Wire Rope/Aircraft Cable*
BREAKING STRENGTHS AND APPROXIMATE WEIGHTS
Diameter Wire Rope Aircraft Aircraft Weight
(in.) 6x25 & 6x37** Cable* Cable* In Lbs. Per Foot
IWRC(EIPS) FC GALV7x19 SS GALV 7x7 SS
Sling working load limits whether nylon, wire rope IWRC FC A/C
or chain slings are rated with their respective
vertical, choker, and basket capacities. When 1/16 - - - - .24 .24 - - .008
selecting these slings, careful consideration must 3/32 - - - .46 .50 .46 - - .016
be made for the proper sling to load horizontal 1/8 - - 1.00 .88 .85 .88 - - .029
lifting angle. The greater angle to sling configuration 5/32 - - 1.40 1.20 - 1.20 - - .045
will result in a reduction of sling efficiency and a 3/16 - - 2.10 1.85 1.85 - - - .065
loss of rated work load limits! 7/32 - - 2.80 2.50 - - - - .086
SEE ILLUSTRATION ABOVE: 1/4 3.40 3.02 3.50 3.20 3.10 - .12 .11 .110
5/16 5.27 4.69 4.90 4.50 - - .18 .16 .173
3/8 7.55 6.72 7.20 6.00 - - .26 .24 .243
7/16 10.20 9.10 - - - - .35 .32 -
1/2 13.30 11.80 - - - - .46 .42 -
9/16 16.80 14.90 - - - - .59 .53 -
(A) at a 90º sling to load angle the sling is at 5/8 20.60 18.30 - - - - .72 .66 -
100% of the WLL. 3/4 29.40 26.20 - - - - 1.04 .95 -
7/8 39.80 35.40 - - - - 1.42 1.29 -
(B) at a 60º sling to load angle a loss of 14% 1 51.70 46.00 - - - - 1.85 1.68 -
efficiency occurs and the sling is capable 1-1/8 65.00 57.80 - - - - 2.34 2.13 -
of lifting only 8,600 lbs. 1-1/4 79.90 71.10 - - - - 2.89 2.63 -
1-3/8 96.00 85.50 - - - - 3.50 3.18 -
(C) at a 45º sling to load angle a loss of 30% 1-1/2 114.00 101.00 - - - - 4.16 3.78 -
efficiency occurs and the sling is capable
of lifting only 7,000 lbs. * Not intended for aircraft use. Designed for industrial and marine applications. ** 6x25 and 6x37 breaking strengths are the same.
(D) at a 30º sling to load angle the working ! Observe Rated Capacity
load limit is reduced by 50% and the WARNING!
is capable of lifting only 5,000 lbs.
Work load limits will be reduced when less than 90º
Load Angle Efficiency from horizontal (See Efficiency Chart) Angles of less
Horizontal Efficiency Loss of than 30º are not to be used. Inspect before use.
Lift Angle Rating Rating Additional requirements and safe operating practices
90º 100% 0% are outlined in current OSHA, Federal Register Part
80º 98% 2% 29, 1910.184 and ASME B30.9 c-2000. Death or
injury can occur from improper use or maintenance!
70º 94% 6%
60º 86% 14%
50º 76% 24%
45º 70% 30%
40º 64% 36%
30º 50% 50%
110
Turnbuckles
HG-228 Green Pin® Jaw & Jaw Turnbuckles with Cotter Pin
DIMENSIONS (in.)
Working Diameter Take Length Length Length Opening Length Diameter Thickness Diameter Weight ea.
Load Limit Thread Up Closed Position Open Position Closed Position Jaw Inside Pin Jaw Eye Jaw Eye (lbs)
e g
ta b cd .94 f .62 h i
14.48 .94 1.49 .62 .62 1.61 5.9
2.36 3/4 6 17.40 19.17 17.24 .94 1.49 .62 .62 1.61 6.68
2.36 3/4 9 20.39 25.15 20.15 .94 1.49 .62 .62 1.61 7.25
2.36 3/4 12 24.29 31.14 20.78 1.06 1.49 .74 .62 1.61 8.04
2.36 3/4 18 43.11 29.13 1.06 1.65 .74 .74 1.88 10.8
3.27 7/8 12 22 32.48 25.03 1.18 1.65 .86 .74 1.88 13.11
3.27 7/8 18 28.03 44.52 31.06 1.18 1.96 .86 .78 2.16 11.48
4.54 1 6 17.59 21.85 21.06 1.18 1.96 .86 .78 2.16 15.34
4.54 1 12 35.35 33.81 26.88 1.18 1.96 .86 .78 2.16 18.51
4.54 1 18 29.52 48.82 32.87 1.73 1.96 1.14 .78 2.16 19.62
4.54 1 24 35.51 57.83 38.85 1.73 2.79 1.14 1.02 2.67 26.23
6.9 1-1/4 12 25.23 36.06 29.44 1.73 2.79 1.14 1.02 2.67 29.98
6.9 1-1/4 18 31.22 47.95 35.43 2.04 2.79 1.37 1.02 2.67 31.3
6.9 1-1/4 24 37.83 60.55 42.08 2.04 2.79 1.37 1.1 3.14 37.25
9.71 1-1/2 12 26.57 37.04 31.73 2.04 2.79 1.37 1.1 3.14 42.55
9.71 1-1/2 18 32.48 48.97 37.63 2.32 2.79 1.65 1.1 3.14 45.63
9.71 1-1/2 24 38.58 61.02 43.74 2.32 3.38 1.65 1.29 3.54 55.11
12.7 1-3/4 18 36.73 51.57 43.11 2.48 3.38 2 1.29 3.54 63.27
12.7 1-3/4 24 42.67 63.54 49.05 2.95 3.66 2.24 1.61 4.25 100.08
16.8 2 24 45.39 65.82 52.67 3.54 4.48 2.75 1.61 5.62 194
27.2 2-1/2 24 49.37 72.04 58.22 4.33 1.61 6.22 216.05
34 2-3/4 24 51.37 73.93 61.45
Green Pin® Eye & Eye Turnbuckles
DIMENSIONS (in.)
Working Diameter Take Length Length Length Diameter Width Length Length Weight
Load Limit Thread Up Closed Position Open d e Inside Inside Closed Position Ea. (lbs)
6 7.2 .39
t a 6 b c .47 f g h 1.03
.54 3/8 9 11.49 16.85 7.59 .47 .51 1.14 1.92 1.85
1 1/2 12 12.79 17.91 10.59 .47 .7 1.41 2.28 2.31
1 1/2 6 15.74 23.89 13.62 .55 .7 1.41 2.24 2.77
1 1/2 9 18.74 29.92 7.99 .55 .7 1.41 2.24 2.97
1.59 5/8 12 19.8 10.98 .55 .82 1.73 3.11 3.52
1.59 5/8 6 15 25.78 14.01 .66 .82 1.73 3.07 4.23
1.59 5/8 9 17.91 31.81 8.38 .66 .82 1.73 3.07 4.47
2.36 3/4 12 20.91 20.94 11.37 .66 .98 2.12 3.54 5.48
2.36 3/4 18 16.29 26.92 14.4 .66 .98 2.12 3.5 5.84
2.36 3/4 12 19.21 32.95 20.39 .78 .98 2.12 3.5 6.74
2.36 3/4 18 22.2 44.96 14.8 .78 .98 2.12 3.5 8.77
2.27 7/8 6 28.22 34.21 20.78 .94 1.25 2.4 3.93 11.28
3.27 7/8 12 23.66 46.22 9.17 .94 1.25 2.4 3.97 9.59
4.54 1 18 29.68 23.77 15.19 .94 1.41 2.95 4.64 13.05
4.54 1 24 19.56 35.78 21.18 .94 1.41 2.95 4.6 15.8
4.54 1 12 25.47 47.79 27.16 1.41 2.95 4.6 16.57
4.54 1 18 31.41 59.72 15.15 1.18 1.41 2.95 4.56 21.6
6.9 1-1/4 24 37.4 38.74 21.14 1.18 1.81 3.54 5.7 24.93
6.9 1-1/4 12 27.99 50.62 27.12 1.18 1.81 3.54 5.66 26.67
6.9 1-1/4 18 33.89 62.59 15.78 1.25 1.81 3.54 5.66 31.3
9.71 1-1/2 24 39.92 40.27 21.77 1.25 2.12 4.13 6.14 36.37
9.71 1-1/2 18 29.76 52.55 27.75 1.25 2.12 4.13 6.29 37.69
9.71 1-1/2 24 36.06 64.37 22.71 1.49 2.12 4.13 6.22 50.92
12.7 1-3/4 24 41.92 54.96 28.7 1.49 2.36 4.68 7.75 57.98
12.7 1-3/4 24 40.11 66.96 29.37 1.81 2.36 4.68 7.71 89.72
16.8 2 24 46.1 70.19 31.49 2.71 5.78 9.09 141.09
27.2 2-1/2 49.76 77.36 31.49 2 3.14 6.49 10.78 194
34 2-3/4 56.25 80.23 2.24 3.3 12.24
59.17 7
877.446.4352 www.superiortoolrental.com www.midlandtool.com 111
Turnbuckles
Green Pin® Eye & Jaw Turnbuckles with Cotter Pin
DIMENSIONS (in.)
Working Dia. Take Length Closed Length Open Opening Length Dia. Thickness Dia. Dia. Width Length Length Weight ea.
Load Limit Thread Up Position Position Jaw Inside Jaw Pin Jaw Eye Jaw Eye Jaw Eye Inside Inside Closed (lbs)
b c d e f g hi j k l
ta 6 11.14 16.45 .47 .82 .31 .35 .82 .39 .51 1.49 1.92 1.12
.54 3/8 6 12.4 17.51 .62 1.02 .39 .43 1.02 .47 .70 1.41 2.28 1.96
1 1/2 9 15.31 23.5 .62 1.02 .39 .43 1.02 .47 .70 1.41 2.24 2.42
1 1/2 12 18.3 29.48 .62 1.02 .39 .43 1.02 .47 .70 1.41 2.24 2.88
1 1/2 6 14.29 19.13 .7 1.25 .51 .55 1.29 .55 .82 1.73 3.11 3.48
1.59 5/8 9 17.24 25.11 .7 1.25 .51 .55 1.29 .55 .82 1.73 3.07 4.05
1.59 5/8 12 20.23 31.10 .7 1.25 .51 .55 1.29 .55 .82 1.73 3.07 4.89
1.59 5/8 6 15.39 20.03 .94 1.49 .62 .62 1.61 .66 .98 2.12 3.54 5.15
2.36 3/4 9 18.3 26.02 .94 1.49 .62 .62 1.61 .66 .98 2.12 3.5 5.99
2.36 3/4 12 21.29 32.04 .94 1.49 .62 .62 1.61 .66 .98 2.12 3.5 6.5
2.36 3/4 18 27.32 44.01 .94 1.49 .62 .62 1.61 .66 .98 2.12 3.5 7.27
2.36 3/4 12 22.83 33.34 1.06 1.65 .74 .74 1.88 .78 1.25 2.40 3.93 9.59
3.27 7/8 18 28.85 45.35 1.06 1.65 .74 .74 1.88 .78 1.25 2.40 3.97 12.03
3.27 7/8 6 18.58 22.79 1.18 1.96 .86 .78 2.16 .94 1.41 2.95 4.64 10.27
4.54 1 12 24.52 34.8 1.18 1.96 .86 .78 2.16 .94 1.41 2.95 4.6 13.99
4.54 1 18 30.51 46.81 1.18 1.96 .86 .78 2.16 .94 1.41 2.95 4.6 17.59
4.54 1 24 36.45 58.77 1.18 1.96 .86 .78 2.16 .94 1.41 2.95 4.56 18.49
4.54 1 12 26.61 37.36 1.73 2.79 1.14 1.02 2.67 1.18 1.81 3.54 5.7 24.07
6.9 1-1/4 18 32.75 49.48 1.73 2.79 1.14 1.02 2.67 1.18 1.81 3.54 5.66 24.25
6.9 1-1/4 24 38.89 61.57 1.73 2.79 1.14 1.02 2.67 1.18 1.81 3.54 5.66 28.43
6.9 1-1/4 12 28.18 38.66 2.04 2.79 1.37 1.1 3.14 1.25 2.12 4.13 6.14 28.88
9.71 1-1/2 18 34.29 50.74 2.04 2.79 1.37 1.1 3.14 1.25 2.12 4.13 6.29 32.40
9.71 1-1/2 24 40.23 62.71 2.04 2.79 1.37 1.1 3.14 1.25 2.12 4.13 6.22 39.24
9.71 1-1/2 18 38.58 53.38 2.32 3.38 1.65 1.29 3.54 1.49 2.36 4.68 7.75 49.16
12.7 1-3/4 24 44.52 65.39 2.32 3.38 1.65 1.29 3.54 1.49 2.36 4.68 7.71 60.62
12.7 1-3/4 24 47.55 68.03 2.48 3.66 2 1.61 4.25 1.81 2.71 5.78 9.09 94.57
16.8 2 24 52.79 73.46 2.95 4.48 2.24 1.61 5.62 2 3.14 6.49 10.78 149.91
27.2 2-1/2 24 55.27 75.7 3.54 4.33 2.75 1.61 6.22 2.24 3.3 7 112.24 200.62
34 2-3/4
HG-228 Jaw & Jaw Turnbuckles with Cotter Pin
DIMENSIONS (in.)
Thread Dia. HG-228 Working Load Weight A E J K M N BB
& Take Up Item # Limit (lbs)* Ea. (lbs) B Closed G Open Closed Open Closed 4.07
8.18 4.58
† 1/4 x 4 1032493 500 .37 .25 .45 1.66 .64 11.19 7.19 12.18 9.62 6.10
† 5/16 x 4-1/2 1032518 800 .56 .31 .50 2.02 .87 13.07 8.57 14.12 11.50 6.03
† 3/8 x 6 1032536 1200 .85 .38 .53 2.11 .85 16.25 10.25 17.50 14.14 9.36
1/2 x 6 1032554 2200 1.82 .50 .64 3.22 1.07 18.65 12.65 20.14 17.43 12.36
1/2 x 9 1032572 2200 2.29 .50 .64 3.20 1.07 24.94 15.94 26.43 20.43 6.03
1/2 x 12 1032590 2200 2.71 .50 .64 3.20 1.07 30.94 18.94 32.43 15.18 9.39
5/8 x 6 1032616 3500 3.21 .63 .79 3.90 1.32 19.74 13.74 21.82 19.16 12.39
5/8 x 9 1032634 3500 3.95 .63 .79 3.89 1.32 26.08 17.08 28.16 22.16 6.13
5/8 x 12 1032652 3500 4.58 .63 .79 3.89 1.32 32.08 20.08 34.16 17.68 9.59
3/4 x 6 1032670 5200 4.80 .75 .97 4.71 1.52 21.09 15.09 23.68 21.08 12.59
3/4 x 9 1032698 5200 5.85 .75 .97 4.68 1.52 27.49 18.49 30.08 24.08 18.53
3/4 x 12 1032714 5200 6.72 .75 .97 4.68 1.52 33.49 21.49 36.08 30.08 12.16
3/4 x 18 1032732 5200 8.45 .75 .97 4.71 1.52 45.49 27.49 48.08 25.62 18.63
7/8 x 12 1032750 7200 9.37 .88 1.16 5.50 1.77 34.65 22.65 37.62 32.09 6.18
7/8 x 18 1032778 7200 11.8 .88 1.16 5.50 1.77 47.12 29.12 50.09 21.18 12.18
1x6 1032796 10000 10.4 1.00 1.34 6.09 2.05 23.82 17.82 27.18 27.18 18.18
1 x 12 1032812 10000 13.8 1.00 1.34 6.09 2.05 35.82 23.82 39.18 33.18 24.84
1 x 18 1032830 10000 17.1 1.00 1.34 6.09 2.05 47.82 29.82 51.18 39.78 12.06
1 x 24 1032858 10000 21.0 1.00 1.34 6.09 2.05 60.42 36.42 63.78 31.58 18.06
1-1/4 x 12 1032876 15200 21.9 1.25 1.84 8.09 2.82 39.37 27.37 43.58 37.58 24.62
1-1/4 x 18 1032894 15200 25.9 1.25 1.84 8.09 2.82 51.37 33.37 55.58 44.14 12.32
1-1/4 x 24 1032910 15200 29.8 1.25 1.84 8.09 2.82 63.93 39.93 68.14 33.68 18.32
1-1/2 x 12 1032938 21400 32.6 1.50 2.06 8.93 2.81 40.76 28.76 45.68 39.68 24.94
1-1/2 x 18 1032956 21400 38.0 1.50 2.06 8.93 2.81 52.76 34.76 57.68 46.30 18.37
1-1/2 x 24 1032974 21400 43.5 1.50 2.06 8.93 2.81 65.38 41.38 70.30 41.16 24.37
1-3/4 x 18 1033018 28000 53.5 1.75 2.60 9.36 3.35 53.35 35.35 59.16 47.16 24.48
1-3/4 x 24 1033036 28000 61.1 1.75 2.60 9.36 3.35 65.35 41.35 71.16 52.72 24.60
2 x 24 1033054 37000 96.3 2.00 2.62 11.80 3.74 69.64 45.64 76.72 58.18 24.65
2-1/2 x 24 1033072 60000 167 2.50 3.06 13.26 4.44 72.97 48.97 82.18 61.50
2-3/4 x 24 1033090 75000 199 2.75 3.69 14.92 4.19 74.75 50.75 85.50
*Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit. † Mechanical Galvanized
112
Turnbuckles
HG-226 Eye & Eye Turnbuckles
DIMENSIONS (in.)
Thread Dia. & HG-226 Working Load Weight A OpJen CloKsed OpMen CloNsed R S CloXsed BB
Take Up Item # Limit (lbs)* Each (lbs)
.34 1.76 4.07
† 1/4 x 4 1031252 500 .29 .25 11.94 7.94 12.38 8.38 .81 .44 2.20 4.58
† 5/16 x 4-1/2 1031270 800 .48 .31 13.92 9.42 14.48 9.98 .95 .53 2.48 6.10
1031298 1200 .75 .38 17.56 11.56 18.24 12.24 1.13 .71 3.56 6.03
† 3/8 x 6 1031314 2200 1.72 .50 19.94 13.94 20.82 14.82 1.41 .71 3.54 12.36
1/2 x 6 1031350 2200 2.63 .50 32.23 20.23 33.11 21.11 1.41 .88 4.35 6.03
1/2 x 12 1031378 3500 2.75 .63 21.72 15.72 22.72 16.72 1.80 .88 4.34 12.39
5/8 x 6 1031412 3500 4.12 .63 34.06 22.06 35.06 23.06 1.80 1.00 5.12 6.13
5/8 x 12 1031430 5200 4.22 .75 23.24 17.24 24.50 18.50 2.09 1.00 5.09 12.59
3/4 x 6 1031476 5200 6.12 .75 35.64 23.64 36.90 24.90 2.09 1.00 5.12 18.53
3/4 x 12 1031494 5200 7.83 .75 47.64 29.64 48.90 30.90 2.09 1.25 5.79 12.16
3/4 x 18 1031519 7200 8.83 .88 36.70 24.70 38.20 26.20 2.38 1.25 5.79 18.63
7/8 x 12 1031537 7200 11.5 .88 49.17 31.17 50.67 32.67 2.38 1.43 6.50 6.18
7/8 x 18 1031555 10000 9.62 1.00 26.24 20.24 28.00 22.00 3.00 1.43 6.50 12.18
1x6 1031573 10000 13.0 1.00 38.24 26.24 40.00 28.00 3.00 1.43 6.50 18.18
1 x 12 1031591 10000 16.3 1.00 50.24 32.24 52.00 34.00 3.00 1.43 6.47 24.84
1 x 18 1031617 10000 20.2 1.00 62.84 38.84 64.60 40.60 3.00 1.82 8.49 12.06
1 x 24 1031635 15200 19.9 1.25 42.14 30.14 44.38 32.38 3.59 1.82 8.49 18.06
1-1/4 x 12 1031653 15200 23.8 1.25 54.14 36.14 56.38 38.38 3.59 1.82 8.49 24.62
1-1/4 x 18 1031671 15200 27.8 1.25 66.70 42.70 68.94 44.94 3.59 2.12 9.46 12.32
1-1/4 x 24 1031699 21400 28.7 1.50 44.24 32.24 46.74 34.74 4.09 2.12 9.46 18.32
1-1/2 x 12 1031715 21400 34.1 1.50 56.24 38.24 58.74 40.74 4.09 2.12 9.46 24.94
1-1/2 x 18 1031733 21400 39.6 1.50 68.86 44.86 71.36 47.36 4.09 2.38 9.97 18.37
1-1/2 x 24 1031779 28000 50.7 1.75 57.38 39.38 60.38 42.38 4.65 2.38 9.97 24.37
1-3/4 x 18 1031797 28000 58.2 1.75 69.38 45.38 72.38 48.38 4.65 2.69 13.03 24.48
1-3/4 x 24 1031813 37000 83.5 2.00 75.68 51.68 79.18 55.18 5.81 3.12 13.76 24.60
2 x 24 1031831 60000 149 2.50 79.18 55.18 83.18 59.18 6.49 3.25 15.09 24.65
2-1/2 x 24 1031859 75000 174 2.75 81.34 57.34 85.84 61.84 7.00
2-3/4 x 24
*Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit. † Mechanical Galvanized
HG-227 Jaw & Eye Turnbuckles
DIMENSIONS (in.)
Thread Dia. & HG-227 Working Load Weight A E J KM N R X
Take Up Item # Limit (lbs)* Each (lbs) B Closed G Open Closed Open Closed S Closed BB
.81
† 1/4 x 4 1031877 500 .33 .25 .45 1.66 .64 11.57 7.57 12.28 8.28 .95 .34 1.76 4.07
1.13 .44 2.20 4.58
† 5/16 x 4-1/2 1031895 800 .52 .31 .50 2.02 .87 13.50 9.00 14.30 9.80 1.41 .53 2.48 6.10
1.41 .71 3.56 6.03
† 3/8 x 6 1031911 1200 .80 .38 .53 2.11 .85 16.91 10.91 17.87 11.87 1.41 .71 3.54 9.36
1.80 .71 3.54 12.36
1/2 x 6 1031939 2200 1.77 .50 .64 3.22 1.07 19.30 13.30 20.48 14.48 1.80 .88 4.35 6.03
1.80 .88 4.34 9.39
1/2 x 9 1031957 2200 2.25 .50 .64 3.20 1.07 25.59 16.59 26.77 17.77 2.09 .88 4.34 12.39
2.09 1.00 5.12 6.13
1/2 x 12 1031975 2200 2.67 .50 .64 3.20 1.07 31.59 19.59 32.77 20.77 2.09 1.00 5.09 9.59
2.09 1.00 5.09 12.59
5/8 x 6 1031993 3500 2.98 .63 .79 3.90 1.32 20.73 14.73 22.27 16.27 2.38 1.00 5.12 18.53
2.38 1.25 5.79 12.16
5/8 x 9 1032019 3500 3.72 .63 .79 3.89 1.32 27.07 18.07 28.67 19.61 3.00 1.25 5.79 18.63
3.00 1.43 6.50 6.18
5/8 x 12 1032037 3500 4.35 .63 .79 3.89 1.32 33.07 21.07 34.61 22.61 3.00 1.43 6.50 12.18
3.00 1.43 6.50 18.18
3/4 x 6 1032055 5200 4.51 .75 .97 4.71 1.52 22.17 16.17 24.09 18.09 3.59 1.43 6.47 24.84
3.59 1.82 8.49 12.06
3/4 x 9 1032073 5200 5.56 .75 .97 4.68 1.52 28.57 19.57 30.49 21.49 3.59 1.82 8.49 18.06
4.09 1.82 8.49 24.62
3/4 x 12 1032091 5200 6.42 .75 .97 4.68 1.52 34.57 22.57 36.49 24.49 4.09 2.12 9.46 12.32
4.09 2.12 9.46 18.32
3/4 x 18 1032117 5200 8.14 .75 .97 4.71 1.52 46.57 28.57 48.49 30.49 4.65 2.12 9.46 24.94
4.65 2.38 9.97 18.37
7/8 x 12 1032135 7200 9.10 .88 1.16 5.50 1.77 35.68 23.68 37.91 25.91 5.81 2.38 9.97 24.37
6.49 2.69 13.03 24.48
7/8 x 18 1032153 7200 11.6 .88 1.16 5.50 1.77 48.15 30.15 50.38 32.38 7.00 3.12 13.76 24.60
3.25 15.09 24.65
1x6 1032171 10000 10.0 1.00 1.34 6.09 2.05 25.03 19.03 27.59 21.59
1 x 12 1032199 10000 13.4 1.00 1.34 6.09 2.05 37.03 25.03 39.59 27.59
1 x 18 1032215 10000 16.7 1.00 1.34 6.09 2.05 49.03 31.03 51.59 33.59
1 x 24 1032233 10000 20.6 1.00 1.34 6.09 2.05 61.63 37.63 64.19 40.19
1-1/4 x 12 1032251 15200 20.9 1.25 1.84 8.09 2.82 40.76 28.76 43.98 31.98
1-1/4 x 18 1032279 15200 24.8 1.25 1.84 8.09 2.82 52.76 34.76 55.98 37.98
1-1/4 x 24 1032297 15200 28.8 1.25 1.84 8.09 2.82 65.32 41.32 68.54 44.54
1-1/2 x 12 1032313 21400 30.6 1.50 2.06 8.93 2.81 42.50 30.50 46.21 34.21
1-1/2 x 18 1032331 21400 36.0 1.50 2.06 8.93 2.81 54.50 36.50 58.21 40.21
1-1/2 x 24 1032359 21400 41.5 1.50 2.06 8.93 2.81 67.12 43.12 70.83 46.83
1-3/4 x 18 1032395 28000 52.1 1.75 2.60 9.36 3.35 55.37 37.37 59.77 41.77
1-3/4 x 24 1032411 28000 59.7 1.75 2.60 9.36 3.35 67.37 43.37 71.77 47.77
2 x 24 1032439 37000 89.9 2.00 2.62 11.80 3.74 72.66 48.66 77.95 53.95
2-1/2 x 24 1032457 60000 158 2.50 3.06 13.26 4.44 76.08 52.08 82.68 58.68
2-3/4 x 24 1032475 75000 187 2.75 3.69 14.92 4.19 78.05 54.05 85.67 61.67
*Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit. † Mechanical Galvanized
877.446.4352 www.superiortoolrental.com www.midlandtool.com 113
RATCHET BINDERS 1-3/8"
Ratchet Binders
2" 1-3/4" 1-3/8"
1-3/4" 2"
Dynamometer
DYNAFOR - LLXh
LLXh
SPECIFICATIONS
Item # LLXh
Maximum Capacity 25 Ton
Test Load 50 Ton
Safety Coeifficient Minimum 4
0.2 % according to ISO 376. 69.8ºF
Precision 50 daN
DIMENSIONS (in.) Increment 10 daN
A 14.17 Max. Display 27500 daN
B 10.91 Autonomy From 300 to 1000 h depending of functions
C 2.2 Radio Scope ft. 262.47 (in open field) (I.P. 219.82 = 196.85)
D 5.28 RF Technology 2.4 Ghz
E 2.68 Weight lb. 14.55
F 2.28 IP Protection I.P. 65 (option: I.P. 67)
Usage From -4º to 104ºF
Sensitivity to Tº 0.05% per 50ºF
Sensor Material Aluminum
114
Heaters
F-1000T Construction Heater
FEATURES
• Engineered for easy operation and minimal servicing
• Electronic direct spark ignition control
• Equipped with 100% flame safeguard system
• Designed for commercial applications
• Just turn the fuel selector valve to change the fuel supply
• Environmentally friendly with minimal combustion impurities
• Temporary heat for construction and maintenance
SPECIFICATIONS
Heat Capacity High Fire: 1,000,000 btuh, Low Fire: N/A
Fuel Natural Gas, Propane
Fuel Capacity Natural Gas: 1,000 CFH, Propane: 10.92 GPH F-1000T
Inlet Pressure Natural Gas: 10" W.C. Min, Propane: 11" W.C. Max
Power Requirement 115 V / 60 Hz / 1 PH / 20 Amp
Fan Motor 1 HP
Ignition Direct Spark Ignition
Air Circulation 7,000 CFM
Thermostat Control Yes
Required Equipment Second Stage Regulator: B42Rq .25 (1-1/4" NPT)
Typical Hose Assembly: S54180-20 1-1/4"
x 15' Hose Assembly
Air Outlet 26" Diameter
Dimensions / Weight L 61" L 29" H 38" / 356 lbs.
TIH L44 Series Bearing Heater
The SKF m20 concept represents the weight (kg) of the heaviest SKF spherical roller bearing of
series 231 which can be heated from (20 to 110ºC) 68 to 230ºF in 20 minutes. This defines
the heater’s power output instead of its power consumption. Unlike other bearing heaters,
there is a clear indication of how long it takes to heat a bearing, rather than just the
maximum bearing weight possible.
FEATURES
• Advanced power electronics, with accurate electric current control, help control the
temperature rate increase
• Automatic demagnetization reduces the risk of ferrous debris contamination after heating
• Thermal overheating protection reduces the risk of damage to the induction coil and the
electronics, enhancing reliability and safety
• Bearings can be heated vertically or horizontally
• Compact design allows the TIH L44 series to be easily transported by forklift
SPECIFICATIONS
Designation TIH L44
Max. Bearing Weight 2.600 lb. (1.200 kg)
Bore Diameter Range 5.9" – 31.5" (150-180 mm)
Operating Area (w x h) 16.7" x 19.4" (425 x 492 mm)
Coil Diameter 6.9" (175 mm)
Standard Yokes (Included) To Suit TIH L44
Bearing Minimum Bore Diameter 5.9" (150 mm)
Optional Yokes to Suit Bearing 3.9" (100 mm)
Minimum Bore Diameter
Max. Power Consumption TIH L44/MV: 20–23 kVA TIH L44/LV: 20–24 kVA
Voltage TIH L44/LV TIH L44/MV
Temperature Control 68º to 482ºF (20 to 250ºC)
Demagnetisation According to SKF Norms ›2 A/cm
Max. Heating Temperature 482ºF (250ºC)
Dimensions w 47.3" x d 23.6" x h 33.5" w 1,200 x d 600 x h 850 mm
Total Weight (Includes Yokes) 714 lbs. (324 kg)
877.446.4352 www.superiortoolrental.com www.SuwpewriowrT.omolRidenltaaln.cdomto8o77l.-c44o6m-4352 115
Lever & Chain Hoist
Lever Hoist 1-1/2 Ton 2-3/4 Ton 3 Ton 6 Ton 9 Ton
3/4 Ton
The LB Series of lever hoists offer a low headroom, compact design that is perfect for use in tight quarters.
Regarded as the best lever hoists in the industry, our LB Series is recommended for use in heavy-duty
construction work, mining, manufacturing, shipbuilding and day-to-day maintenance and repair.
SPECIFICATIONS DIMENSIONS (in.)
Cap Item # Headroom
Pull to Lift a b D e f g Load Chain Net Shipping Weight
C Load Diameter (mm) x Weight Weight for Add’l
Load Chain at 5 ft. Lift Approx. 1 Foot of Lift
(Tons) (lbs.) Strands (lbs.)
3/4 54 (lbs.) (lbs.)
1 72
LB008 11.0 5.7 4.7 9.6 3.8 1.6 0.9 5.6 x 1 13 13 0.5
LB010 11.8
5.7 4.7 9.6 3.8 1.6 1.1 5.6 x 1 13 13 0.5
1-1/2 LB015 13.2 64 6.3 5.0 10.4 3.9 1.6 1.3 7.1 x 1 18 18 0.7
2 LB020 14.8 59
6.8 5.9 10.4 4.0 1.8 1.4 8.8 x 1 25 26 1.1
2-3/4 LB028 14.8 81 6.8 5.9 10.4 4.0 1.8 1.4 8.8 x 1 25 26 1.1
3 LB030 15.6 69
6 LB060 21.3 72 7.5 6.3 16.3 4.4 1.8 1.5 10.0 x 1 33 35 1.5
9 LB090 26.8 78
7.5 8.5 16.3 4.4 2.3 2.0 10.0 x 2 57 60 3.2
7.5 12.0 16.3 4.4 4.1 2.9 10.0 x 3 88 93 4.7
116
3/4 - 2-3/4 Ton Lever HMoaisntusal-
3 Ton
6 Ton 9 Ton
877.446.4352 www.superiortoolrental.com www.midlandtool.com 117
Chain Hoists
1 Ton CF 1-1/2 Ton CF 2 Ton CF 3 Ton CF 2 Ton S.S. LHH 3 Ton S.S. LHH
Harrington CF hand chain hoists give you a practical alternative thanks to an economical design using fewer parts
for trouble-free service. Outstanding durability is due to a die-cast aluminum body and high-strength, heat-treated
main pinion shaft and load gear. Pre-lubricated ball bearings, precision machined gears, and a Weston-style
load brake make lifting smooth and easy, while allowing long service and low maintenance.
SPECIFICATIONS DIMENSIONS
Model Cap Item # Headroom Pull to Lift Overhaul Load Chain Dia. Weight Weight for Add’l a b d e f g x
No. C Load Ratio (mm) x Load at 10 ft. Lift 1 Foot of Lift
(tons) (in) (lbs) Load Chain Strands (lbs) (lbs) (in) (in) (in) (in) (in) (in) (in)
1/2 CF005 12.8 60 19 5.0 x 1 24 1.0 5.4 5.9 10 2.0 2.4 1.1 -
1 CF010 14.6 72 31 6.3 x 1 29 1.2 5.8 6.9 10 2.3 2.9 1.1 -
CF 1-1/2 CF015 17.3 84 41 7.1 x 1 40 1.4 6.0 8.0 10 2.3 2.3 1.4 -
2 CF020 20.1 80 63 6.3 x 2 47 1.8 5.8 8.0 10 2.3 2.3 1.4 -
3 CF030 23.2 92 81 7.1 x 2 62 2.1 6.0 9.4 10 2.4 2.7 1.7 -
LHH 2 S.S. LHH-2B 15 88 75 7.9 x 1 46 1.8 7.25 8.5 8.5 3.5 - 1.65 -
3 S.S. LHH-3B 17.1 84 95 10 x 1 67 2.1 7.80 10 10 3.75 - 1.89 -
CF 5 CF050 24.4 92 134 7.1 x 3 82 2.9 6.0 13.5 10 2.4 4.5 1.8 -
10 CB100 29.9 72 396 9.0 x 4 186 5.5 7.6 17.2 14.9 4.4 12.1 2.9 11.6
CB 15 CB150 40.2 74 594 9.0 x 6 346 7.9 10.6 19.4 15.9 4.7 13.3 3.1 12.6
20 CB200 46.5 72 x 2 396 x 2 89.0 x 8 524 10.9 14.7 29.4 16.3 7.4 14.7 3.2 13.8
118
5 Ton CF 10 Ton CB 15 Ton CB Chain Hoists
20 Ton CB
877.446.4352 www.superiortoolrental.com www.midlandtool.com 119
Refinery or Non-Spark
Air Tools and Accessories
Pneumatic Reciprocating Saw 46 CFM
#5 1217 0020
FEATURES
• Cuts steel pipe and channel 1/2" to 4" dia., plastic pipe to 8" dia.
• Ideal for the toughest use in refineries, chemical plants, gas utilities,
construction, offshore oil, mining, marine and demolition industries
• Can be mounted on a pipe clamp to make 90º cuts
• Accepts universal saw blades or thicker, double-tang heavy-duty saw blades
Pneumatic Portaband Saws
FEATURES
• 4-3/4" & 7" OD cutting capacity
• Fast, on-site cutting
• Safer in hazardous atmospheres than electric saws
#5 6003 0010
Pneumatic Portable Band Saws Capacity
Motor Power Blade Speed
Item # and Specs. (RPM) Round Regular Blade Housing Overall Air Weight
Size Length Connection (lbs.)
14
AirBand 0.7 HP, 90 PSI, Variable 4-3/4" 4-1/2" x 4-3/4" 44-7/8" Aluminum 21-1/2" 1/4" NPT
5 6003 0010 20 CFM 130-220 x 1/2" (ID) 28
Deep Throat AirBand 1.3 HP, 90 PSI, Variable 7" 7" x 7" 66" x 5/8" Stainless 28-3/4" 1/2" NPT
5 6031 0010 43 CFM 240-295 Steel (ID)
120
Non-Spark Air Tools
Portable Power Hacksaw
FEATURES
• Cut pipe up to 24" OD in one pass
• Chain clamps and profile clamps available for accurate 90º
cutting of pipe and structural steel
• Accommodate heavy-duty blades up to 37" long
• Optional saw blade guides to increase blade stability
SPECIFICATIONS #5 1212 0050 #5 1212 0050
1.5 HP
Item # Lever
Power 90 psi
Throttle 51 cfm
Air Pressure
Air Consumption 100 - 350
Strokes per Min. 2-3/8"
Blade Stroke 1/2" ID
Hose Size 15.4 lbs
Weight
ACCESSORIES
Hacksaw Blades FOR PURCHASE ONLY
Hacksaw Blades - 8" up to 37" long
Item # Dimensions Steel and Max. Dia. Item # Dimensions Steel and Max. Dia.
Length Teeth/Inch Nonferrous Metal of Cut Length Teeth/Inch Nonferrous Metal of Cut
Z22-9 HSS 8" 8 Steel/Aluminum 3-1/8" Z22-72 HSS 20" 14 Steel 14-5/8"
Z22-10 HSS 8" 16 Steel 3-1/8" Z22-30 HSS 21" 12 Steel 15-5/8"
Z22-11 HSS 8" 24 Sheet Metal 3-1/8" Z22-30 HSS-SL* 21" 12 Stainless Steel 15-5/8"
Z22-6 HSS 12" 16 Steel 6-5/8" Z22-73 HSS 24" 14 Steel 18-1/2"
Z22-6 HSS-SL* 12" 16 Stainless Steel 6-5/8" Z22-74 HSS 24" 8 Steel/Aluminum 18-1/2"
Z22-31 HSS 12" 12 Steel 6-5/8" Z22-75 HSS 30" 12 Steel 24-7/8"
Z22-7 HSS 16" 16 Steel 10-5/8" Z22-75 HSS-SL* 30" 12 Stainless Steel 24-7/8"
Z22-29 HSS 16" 8 Steel/Aluminum 10-5/8" Z22-37 HSS 37" 12 Steel 31-7/8"
Blade Guide (Bow)
SPECIFICATIONS 5 1207 9970 5 1207 8910
Item # 13" 21"
For Outside Diameter 20" 30"
Min. Blade Length Required #5 1202 9960-SS
#5 1202 9960
Pipe Clamps
#5 1207 9910
SPECIFICATIONS 5 1202 9960 5 1201 9060-SS 5 1207 9910
Item # 12-3/4" 12-3/4" 6"
For Outside Diameter (O.D.) -
39-3/8" Chain Extension Item # 5 1202 9030 Item # 5 1202 9030-SS -
Chain Extension O.D. 24" 24"
877.446.4352 www.superiortoolrental.com www.midlandtool.com 121
Concrete & Steel Saws
122
Saws
20" Pneumatic Concrete Chain Saw CS 536163-3
FEATURES AirFORCE Premium Chains
For concrete cutting with
• Cut with ease, speed and portability through reinforced concrete, steel reinforcement
brick, block, Concrete pipe, and natural stone 20" – Item # CC 05-5080
• The powerful CS 536163-3 air saw is designed to cut through
walls, floors and columns in a single pass
• 20" maximum depth of cut
• Safety operating trigger prevents accidental starting
• No gas or engine fumes to deal with
• Pays for itself every time you use it with faster cutting and completion
of most jobs in a fraction of the time other saws would take
SPECIFICATIONS
Item # Power No Load Speed Max. Depth Motor Weight w/ No Load Torque Noise Level
(HP) (RPM) of Cut Specifications* Bar & Chain (in.-lbs.) at 3 ft.
CS 536163-3 6.5 5700 20" 124 CFM @ 90 PSI (6 bar) 34 104 88 dB
* When operating a compressor with pressure greater than 90 PSI, it is recommended to use a “service” unit with pressure regulator” in-line to prevent
over-speeding the saw.
18" Pneumatic Hand-Held Concrete Saw
FEATURES
• 18" max blade capacity
• Safe to operate both indoors and outdoors
• No gas or engine fumes
• Can cut with a wet saw
• A 3/4" water connection port is built in for wet cutting
or dust suppression.
SPECIFICATIONS RPM Max. Depth Max. Blade CFM@ Drive CSH 150
(No Load) of Cut Capacity 100 psi
Item # Saw Type Power H.P. 7" Weight
3200 18" 92 Gearbox 28 lbs.
CSH 150 Hand-held 9.5
14" Gas Powered Chop Saw TS 420
FEATURES
• 14" maximum wheel size
• Gas operated
• Ideal for any outdoor application when cutting concrete,
steel or metal decking, ductile pipe, brick, block, and asphalt
• 12" and 14" abrasive and diamond blades are available to
match the material in which you are cutting
SPECIFICATIONS
Item # Saw Type Weight Fuel Max. Spindle Arbor Maximum Maximum
Capacity Speed Size Wheel Size Cutting Depth
TS 420 Hand-held 20 mm
21.2 lbs. 24 oz. 5,350 rpm 14" 4.9"
877.446.4352 www.superiortoolrental.com www.midlandtool.com 123
124
877.446.4352 www.superiortoolrental.com www.midlandtool.com 125
Air Handling & Accessories
Jet Fan Venturi Type Air Movers
FEATURES TX-JF20
• Operates on compressed air FEATURES
• Use for general ventilation in any location where
• Operates on compressed air or steam
compressed air is available • No moving parts
• Suited for ventilation of tanks, process vessels, or • Used for venting hazardous areas
• Connection for ground wire
other confined areas for the removal of hazardous fumes • Can be used as a blower or exhauster
or contaminated air from welding, sandblasting and other • Maintenance is minimal
operations
• Rated operating pressure 40-110 PSI SPECIFICATIONS
• Design allows for lower RPMs while still moving more air
• Use as blower or exhauster Total Air Flow / Output Air Consumption
• Heaviest-duty fan in the industry
SPECIFICATIONS Item # CFM @60 PSI CFM @80 PSI 60 PSI 80 PSI
Item #
Net Weight TX-JF20 TX3AMS 981 1182 50 CFM 62 CFM
Mounting Slot Diameter 95 LBS
Bolt Circle Diameter TX3AM 1231 1462 45 CFM 62 CFM
Inlet 1"
Max PSI 20" *API TX6AM 2885 3347 98 CFM 124 CFM
AT 80 PSI Air Usage is 3/4" NPT
110 PSI TX8AM 4152 4929 152 CFM 193 CFM
186 CFM
TX10AM 6182 7304 209 CFM 274 CFM
DIMENSIONS
Capacity / Output It em # Overall Diameter Diameter NPT Bolt Circle Base Slot Net
Length of Base Top of horn Size Diameter Diameter Weight
The CFM’s Will Decrease @ 60 PSI average CFM 7600 TX3AMS
against static pressure @ 80 PSI average CFM 9100 TX3AM 16.75" 7.31" 6.0" 1/2" 6.56" 0.4 5.5 lb.
TX6AM 30.5" 7.31" 7.0" 1/2" 6.56" 0.4 8.5 lb.
* FLANGES: Matches 20" American Petroleum Institute tank opening. TX8AM 44.25" 11.25" 12.5" 1" 10.5" 0.4 22.3 lb.
TX10AM 46.06" 14.37" 14.25" 1" 13.62" 0.5 36.0 lb.
48.0" 17.0" 16.75" 1" 15.5" 1.0 42.1 lb.
COPPUS Portable Ventilators
FEATURES
• 1 HP, 115 volt 3,000 cfm
• Accepts ducting on inlet and outlet ends
• Heavy gauge, powder coated steel and cast aluminum construction
• Spark resistant fan blades
SPECIFICATIONS cfm (m3/hr) Air Flow Through Duct (Straight Runs)
250CV Item # 10' 20' 30' 50'
250CV
cfm m3/hr cfm m3/hr cfm m3/hr cfm m3/hr
2940 5098 2620 4452 2480 4214 2300 3908
126
MADE INTHE USA Air Handling
15 Gallon Air Manifold Tank 30 Gallon Air Manifold Tank
SPECIFICATIONS SPECIFICATIONS
Item # AT-15 Item # AT-30
# of 3/4" Outlets 8 Outlet Size (Qty) 3/4"(2), 1"(4), 2"(2)
Capacity 15 gal Capacity 30 gal
Working Pressure 200 psi Working Pressure 200 psi
Test Pressure 300 psi Test Pressure 260 psi
Inlet Size 2" Inlet Size 3"
Tank Diameter 12" AT-15 Tank Diameter 16" AT-30
AT-60 AT-400
Width with Fittings 22-1/2" Width with Fittings 36"
Weight 72 lbs Weight 115 lbs
Dimensions H 16-1/2" L 44" Dimensions H 27" L 44"
60 Gallon Air Manifold Tank 400 Gallon Air Manifold Tank
SPECIFICATIONS SPECIFICATIONS
Item # AT-60 Item # AT-400
Outlet Size (Qty) 1"(4), 2"(2), 2"(2) Outlet Size (Qty) 3/4"(1), 1-1/2"(1), 2"(3)
Capacity 60 gal Capacity Aprox 358 gal
Working Pressure 200 psi MAWP 165 psi at 400ºF
Test Pressure 260 psi MDMT -20ºF at 165 psi
Inlet Size 3" Inlet Size 2"
Tank Diameter 20" Tank Diameter 36"
Width with Fittings 39" Width with Fittings 48"
Weight 193 lbs Weight 696 lbs
Dimensions H 31" L 54" Dimensions H 39-1/8" L 88-7/8"
1060 Gallon Air Manifold Tank
SPECIFICATIONS
Item # AT-1060
Outlet Size (Qty) 2"(3)
Diameter 48 O.D.
Capacity Approx 1060 gal
MAWP 155 psi at 400ºF
MDMT -20ºF at 155 psi
Inlet Size 2"
Weight 1966 lbs. AT-1060
41’’ CRM L4208.5C
In-Line Regulators
Oiler / Filter / Regulator / Cage HiVis Twin-PAK
Single Operator For Bull Hose Double Operator
• Air delivery system that HV-TWIN-PAK
allows two operators to
run tools simultaneously
from one air supply.
Dimensions H 15" L 28-1/2" D 10"
Weight 31 lbs
877.446.4352 www.superiortoolrental.com www.midlandtool.com 127
Air Handling
Tanner’s® Compact Dispensers
SPECIFICATIONS
Item# T-90 T-83 T-85 T-87 T-89*
1 12 2
Air Line Size 3/4 12 19 19
26-1/2
Overall Height 10-1/4 7-1/2 11-1/2 11-1/2 16-1/2
16 25 25
T-90 T-83 T-85 T-87 Overall Depth 5-1/2 0.5 22 60
5
Weight (lbs.) 7
Reservoir Capacity (gal.) 0.25
FEATURES Min. CFM Ratings 3–5 3–5 3–5 27.5 27.5
at 100 PSIG
• Engineered for use with air lines up to two inches (7.5 cm2/m3 min.)
• Compact design for easy installation
• Low Maintenance Max. CFM Ratings 180 350 350 1120 1120
• Stationary or portable applications at 100 PSIG
• Durable, safe & dependable (7.5 cm2/m3 min.) 5 10 15 30
• Equally effective with electric or engine-powered services * T-89 Tanner not shown
Initial Purchase 5
of Tannergas (gal.)
Center Punch Band Clamp Steel 3500 Male Nipple
Item # Galv. Steel Item # S.S. Size Width Item # Male Thread Size Hose Size
3501 1/8" 1/4"
F3 FS3 13/16" 3/8" 3502 1/4" 1/4"
F4 FS4 1" 5/8" 3504 3/8" 1/4"
F5 FS5 5/8" 3505 1/4" 3/8"
F311 FS311 1-1/4" 3/8" 3506 3/8" 3/8"
F6 FS6 1-3/8" 5/8" 3508 1/2" 3/8"
F7 FS7 1-1/2" 5/8" 3509 1/4" 1/2"
F8 FS8 1-3/4" 5/8" 3510 3/8" 1/2"
F9 FS9 5/8" 3511 3/4" 1/2"
F10 FS10 2" 5/8" 3512 1/2" 1/2"
F11 FS11 2-1/4" 5/8" 3513 1/2" 3/4"
F12 FS12 2-1/2" 5/8" 3514 3/4" 3/4"
F14 FS14 2-3/4" 5/8" 3515 1" 3/4"
F16 FS16 5/8" 3516 3/4" 1"
F18 FS18 3" 5/8" 3518 1" 1"
F20 FS20 3-1/2" 5/8"
F24 FS24 5/8" Steel 3500 Female Nipple Female Thread Size Hose Size
F28 FS28 4" 5/8" 1/4" 1/4"
F32 FS32 2-1/2" 5/8" Item # 1/4" 3/8"
3542 3/8" 3/8"
5" 3545 3/8" 1/2"
6" 3546 1/2" 1/2"
7" 3550 3/4" 3/4"
8" 3552
3554 Male Hose Size
Air King Female NPT End Spray Hose Male Coupling Thread Size 3/8"
Item # Material Size ( Garden Hose Fitting ) 3/4" GHT 1/2"
1/4" 3/4" GHT 5/8"
AMC1 Iron 3/8" Item # 3/4" GHT 3/4"
1/2" 3/4" GHT
AMC Iron 3/4" SS317 Hose Size
1" SS417 Male 1/2"
AM3 Iron SS517 Thread Size
Size SS617 1/2"
AM8 Iron 1/4" Swivel Hose Male Coupling 1/2" NPT
3/8"
AM13 Iron 1/2" Item # 7/8"-24
3/4"
Air King Male NPT End Material 1" L-3
Item #
Size L-1
AMB1 Iron 3/8"
1/2"
AMB Iron 5/8"
3/4"
AM2 Iron 1"
AM7 Iron
AM12 Iron
Air King Hose End Material
Item #
AMH Iron
AM1 Iron
AM5 Iron
AM6 Iron
AM11 Iron
128
MADE INTHE USA Air Handling
Boss Hose Mender Material Size Boss Clamp 4 Bolt 4 Finger Hose OD From Hose OD To
Plated Iron 3/4" 2-4/64" 2-16/64"
Item # Plated Iron 1" Item # Hose ID 2-32/64" 2-48/64"
M6 Plated Iron 1-1/4" 225 1-1/2" 3-32/64" 3-48/64"
M11 Plated Iron 1-1/2" 275 2"
M16 Plated Iron 2" 375 3"
M21 Plated Iron 2-1/2"
M26 Plated Iron 3" Boss Clamp 4 Bolt 2 Finger
M31
M36 Item # Material Hose ID Hose OD From Hose OD To
BU29 Zink 2" 2-32/64" 2-50/64"
Plated Iron
Quick Couplers Boss Wing Nut
Item # Material Size Item # Material Size
3/8"
VHN600 (V6F6) Male Zinc 3/4" CB Plated Iron 1/2"
3/4" and 1"
VHC600 (6VF6) Female Plated Steel 3/4" B2 Plated Iron 1-1/4" and 1-1/2"
2"
Portable Air Line Lubricators B12 Plated Iron 2-1/2"
3"
B17 Plated Iron 4"
6"
Designed to supply oil to air tools where it is B27 Plated Iron
not practical to use stationary lubricators. Size
B32 Plated Iron 1-1/4"
1-1/2"
Oil Pipe Rec’d Air Max. B37 Plated Iron
Capacity Size Flow@70PSI PSI 2"
Item # Length Height Weight B47 Plated Iron 2-1/2"
0-R 1.4 oz. 1/2" 30 cfm 500 4-1/4" 2-1/4" 0.88 lbs. B67 Zink Plated Iron 3"
4"
1-R 3.7 oz. 3/4" 70 cfm 260 6" 2-3/4" 1.50 lbs. Boss Ground Joint Stem 6"
2-R 11.0 oz. 3/4" 70 cfm 300 7" 3-1/2" 2.00 lbs.
2A-R 11.0 oz. 1" 70 cfm 300 7" 3-1/2" 2.00 lbs. Item # Material
3-R 16.0 oz. 1" 150 cfm 250 10" 3-3/4" 4.25 lbs. GB16 Plated Iron
In-Line Lubricator w/Integral Filter GB21 Plated Iron
GB26 Plated Iron
GB31 Plated Iron
GB36 Plated Iron
GB46 Plated Iron
Item # Oil Cap. Pipe Size Rec’d Air Flow @ 70 PSI Max. PSI Height GB66 Plated Iron
TX-0L-F 1.4 oz. 1/2" 30 cfm 500 2-1/4"
TX-1L-F 3.7 oz. 3/4" 70 cfm 2600 2-3/4" Boss Ground Joint Double Spud
Heavy Duty Impact Wrench Hose Item # Material Thread Size Seat
–
GDB23 Plated Iron 1-1/4" and 1-1/2" –
–
GDB28 Plated Iron 2" –
GDB33 Plated Iron 2-1/2" Seat
Polymer
GDB38 Plated Iron 3" Polymer
Polymer
Boss Ground Joint Female Spud Polymer
Polymer
SPECIFICATIONS Hose I.D. 3/8", 1/2", 3/4" Working PSI 500 Item # Material Thread Size Polymer
GB18 Plated Iron 1-1/4" Polymer
Heavy Duty Rivet Buster & Chipping Hammer Hose GB23 Plated Iron 1-1/2"
GB28 Plated Iron 2" Seat
GB33 Plated Iron 2-1/2" Polymer
GB38 Plated Iron 3" Polymer
GB48 Plated Iron 4" Polymer
GB68 Plated Iron 6" Polymer
Polymer
Boss Ground Joint Male Spud
SPECIFICATIONS Hose I.D. 3/8", 1/2", 3/4" Working PSI 500 Item # Material Thread Size
GM18 Plated Iron 1-1/4"
Standard Air Tool Whip Hose GM23 Plated Iron 1-1/2"
GM28 Plated Iron 2"
GM33 Plated Iron 2-1/2"
GM38 Plated Iron 3"
SPECIFICATIONS Hose I.D. 3/8", 1/2", 3/4" Working PSI 300 Air King 4-Lug Hose End Material Size
Iron 1-1/4"
Item # Iron 1-1/2"
AM16 Iron
AM21 2"
AM26
877.446.4352 www.superiortoolrental.com www.midlandtool.com 129
Pipe Threading Machines
#1224 (p.135) #535 (p.132)
130
#700 Power Drive #700 Power Drive
ALL ACCESSORIES FOR PURCHASE ONLY
Die Heads, Manual Threaders (North American Standards)
Catalog No. Nominal Pipe Size (In.)
Item # 12-R 1/8 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2
SPECIFICATIONS (NPT) National Pipe Taper 37390 37395 37400 37405 37410 37415
Catalog No. 37435 37440 37445 37450 37455 37460
Item # 41935 Alloy RH 37375 37380 37385 37480 37485 37490 37495 37500 37505
Description 700 37525 37530 37535 37540 37545 37550
Pipe Threading Capacity 115V 50/60 Hz Only High-Speed LH 83460 83465 83470 83475 83480 83485
Rod Threading Capacity 1/8"-2" 51857 51862 51867 51872 51877 51882
Max. Geared Threader Cap. 1/4"-1" High-Speed RH 37465 37470 37475 92690 92695 92700 92705 92710 92715
Weight 6
31 lbs. High-Speed for Stainless Steel RH 37510 37515 37520 37570 37575 37580 37585 37590 37595
High-Speed for PVC RH 83450 83455
High-Speed for Plastic Coated Pipe
Alloy for IMC RH
(NPSM)
Catalog No. Item # Accessories Alloy RH 37555 37560 37565
42620 774 Square Dr. Adapter -15/16" Pipe Dies, 00-R, 11-R, 12-R, 0-R, Ratchet Threaders
42625
10883 775 Support Arm for No.700 Catalog No. Nominal Pipe Size – Threads Per Inch
42600 418 Oiler w/1 Gal. Nu-Clear
Thread Cutting Oil
770 Adapter for 00-R and 00-RB
Die Material or Type 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 1-1/4-111/2 1-1/4-111/4 2 -111/2
(NPT) National Pipe Taper
When using the 00-RB die Alloy RH 37810 37815 37820 37825 37830 37835 37840 37845 37850
head in the #700 power drive,
the #770 adapter must also High-Speed RH 37855 37860 37865 37870 37875 37880 37885 37890 37895
be used in conjunction.
High-Speed LH 37050 37055 38060 37065 37070 38075 38080 38085
H.S. For Stainless Steel RH 37900 37905 37910 37915 37920 37925 37930 37935 37940
H.S. For PVC RH 70685 70690 70695 70700 70705 70710 70715
HS Reversible RH 49707 49712 49717 49722 49727
(NPSM) National Pipe Straight Mechanical
Alloy RH 37945 37950 37955 37960 37965 37970 37975 37980 37985
Die Heads, Manual Threaders (North American Standards)
Catalog No. Nominal Pipe Size (In.)
Item # 00-RB 1/4 15/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 1
(UNC) 20 TPI 18 TPI 16 TPI 14 TPI 13 TPI 12 TPI 11 TPI 10 TPI 9 TPI 8 TPI
Alloy RH 37610 37615 37620 37625 37630 37635 37640 37645 37650 37655
Alloy LH 37675 37695
(UNF) 28 TPI 24 TPI 24 TPI 20 TPI 20 TPI 18 TPI 18 TPI 16 TPI 14 TPI 14 TPI
Alloy RH 37710 37715 37720 37725 37730 37735 37740 37745 37755
Alloy LH 37775 37780 37785 37790 37795 37800 37805
Bolt Threaders Button Dies, 00-RB Ratchet Bolt Threaders
Die Material or Type Catalog No. Rod Diameter – Threads Per Inch
(UNC) Unified National Course 1/4-20 5/16-18 3/8-16 7/16-14 1/2-13 9/16-12 5/8-11 3/4-10 7/8-9 1-8
Alloy RH 38335 38340 38345 38350 38355 38360 38365 38370 38375 38380
(UNF) Unified National Fine 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 5/8-18 3/4-16 7/8-14 1-12
Alloy RH 38385 38390 38395 38400 38405 38410 38415 38420 38425 15317
877.446.4352 www.superiortoolrental.com www.midlandtool.com 131
#M5ac3h5ineThreading
#535 Threading Machine
CAPACITIES
• Pipe: 1/8"- 2" ( 4"- 6" with #141 and #161 geared threaders )
• Bolt: 1/4"- 2"
FEATURES
• Generous top cover for keeping tools and fittings handy
• Speed chuck with rocker-action jaws centers and grips work piece instantly
• Can be used with geared threader Models #141 and #161
• Uses Model 816/817 semiautomatic, Model 815A self-opening, Model 811A quick-opening
die heads
Optional Die Heads
Catalog Item # Die Head How Thread Oil Thru Dies Pipe Bolt Used Weight
No. Description Opened Direction Head Used Cap. Cap. On lbs.
Machine NPT Die Heads
97065 811A Universal Q.O RH Yes Univ. 1/8"-2" 1/4"-2" * 12-1/2
97075 815A Universal S.O RH Yes Univ. 1/8"-2" 1/4”-2” * 13
84537 816 Universal S.A RH Yes Univ. 1/8"-3/4" * 13
84532 817 Universal S.A RH Yes Univ. 1"-2" * 13
23282 842 Universal Q.O LH Yes Univ. 1/8"-2" * 12-1/2
10491 555 555 Q.O RH Yes Dual/Bolt 1/8"-3/4" *8
Machine Bolt Die Heads
97045 531 Bolt Q.O RH/LH Yes 500B 1/4"-1" * 7-1/2
1-1/8"-2" * 9
97050 532 Bolt Q.O RH/LH Yes 500B
Machine Mono Die Heads
42047 500A Mono Q.O RH Yes Mono 1/8" * 6-3/4"
42052 500A Mono Q.O RH Yes Mono 1/4" * 7"
42057 500A Mono Q.O RH Yes Mono 3/8" * 7"
42062 500A Mono Q.O
42067 500A Mono Q.O RH Yes Mono 1/2" * 7-1/4"
42072 500A Mono Q.O
42077 500A Mono Q.O RH Yes Mono 3/4" * 7-1/4"
42082 500A Mono Q.O
42087 500A Mono Q.O RH Yes Mono 1" * 8"
RH Yes Mono 1-1/4" * 8"
RH Yes Mono 1-1/2" * 8-1/2"
RH Yes Mono 2" * 8-1/2"
S.O - Self-Opening * 535-535A-1822 Machines and 300, 300 Compact and 300-A w/carriage.
Q.O - Quick-Opening
S.A - Semi-Automatic
132
Mac#h5in3e5AcTchersesaodriinegs
ALL ACCESSORIES FOR PURCHASE ONLY
Pipe Dies for use in Universal Die Heads
(Nos. 504A, 711, 713, 811A, 815A, 816, 817, and 842)
(NPT) (NPSM)
Nominal Pipe Size - Threads Per Inch Nominal Pipe Size - Threads Per Inch
1/8"-27 1/4"-3/8"-18 1/2"-3/4"-14 1"-2"-11-1/2"
Die Material or Type 1/8"-27 1/4"-3/8"-18 1/2"-3/4"-14 1"-2"-11-1/2
Alloy RH 47735
High-Speed RH 47755 47740 47745 47750
High-Speed LH 39587
H.S. For Stainless Steel RH 47775 47760 47765 47770 47845 47850 47855 47860
H.S. For Cast Iron
H.S. For PVC RH 47810 47815 47820
H.S. For Plastic Coated Pipe RH
47780 47785 47790
70740
70745 70750
47785 47790
Pipe Dies for use in 500A Mono Die Heads
Nominal Pipe Size - Threads Per Inch
Die Material or Type 1/8"-27 1/4"-18 3/8"-18 1/2"-14 3/4"-14 1"-11-1/2" 1-1/4"-11-1/2 1-1/2"-11-1/2 2"-11-1/2"
50725 50730 50735 50740
High-Speed RH 50700 50705 50710 50715 50720 50770 50775 50780 50785
H.S. For Stainless Steel RH 50745 50750 50755 50760 50765 50920
(NPSM) 50895 50900
High-Speed RH 50905 50910 50915
Conduit Dies for Universal Die Heads (BEC) Nominal Conduit Size – Threads Per Inch
(ISO) Nominal Conduit Size – Pitch in mm
Die Material or Type 16-32 mm-1.5 40-63 mm-1.5 1/2"-5/8"-18 3/4"-1-1/4"-16 1-1/2"-2-1/2"-14
Alloy RH 50645 50650 66700 66705 66710
877.446.4352 www.superiortoolrental.com www.midlandtool.com 133
M#5a3ch5inTehArecacedsinsgories
ALL ACCESSORIES FOR PURCHASE ONLY
Bolt Dies for Machine Die Heads Bolt Dies for 500B and 531, 532, 541
and 542 Die Heads
Bolt Dies for Universal Die Heads
(Nos. 504A, 711, 811A, 816, 817 and 911 Die Heads) (UNC) (UNF)
(UNC) (UNF) Rod Size – RH LH Rod Size – RH
TPI High-Speed High-Speed TPI High-Speed
Rod Size – TPI RH High-Speed Rod Size – TPI RH High-Speed 1/4"-20 48605 1/4"-28 48690
48295 5/16"-18 48610 48915 5/16"-24 48695
1/4"-20 48215 1/4"-28 3/8"-16 48615 48920 3/8"-24 48700
48305
5/16"-18 48220 48310 7/16"-14 48620 48925 7/16"-20 48705
48315
3/8"-16 48225 3/8"-24 48320 1/2"-13 48625 48930 1/2"-20 48710
48325
7/16"-14 48230 7/16"-20 48330 9/16"-12 48630 48935 9/16"-18 48715
48335
1/2"-13 48235 1/2"-20 48340 5/8"-11 48635 48940 5/8"-18 48720
48375
9/16"-12 48240 9/16"-18 48345 3/4"-10 48640 48945 3/4"-16 48725
48350
5/8"-11 48245 5/8"-18 48355 7/8"-9 48645 48950 7/8"-14 48730
48360 1"-8 48650 48955 1"-12 48735
3/4"-10 48250 3/4"-16 1-1/8"-7 48655 48960 1"-14NS 49305
7/8"-9 48255 7/8"-14 1-1/4"-7 48660 48965 1-1/8"-12 48740
1"-8 48260 1"-14NS * 1-3/8"-6 48665 48970 1-1/4"-12 48745
1-7/8"-7 48265 1"-12 1-1/2"-6 48670 48975 1-3/8"-12
1-1/4"-7 48270 1-1/8"-12 1-3/4"-5 48675 1-1/2"-12 48755
1-3/8"-6 48275 1-1/4"-12 2"-4-1/2 48680 48985
1-1/2"-6 48280 1-3/8"-12
1-3/4"-5 48285 1-1/2"-12 For use with 531, 541 and For use with 532, 542 and
500B 1/4”-1” Die Heads 500B 1-1/8”-2” Die Heads
2"-4-1/2 48290
*NS = Non Standard Dies for Rebar, for use in 500B, 531, 532,
Bolt Dies for 500B, 532 and 542 Die Heads and 542 Die Heads
Rod Size – TPI (8 UN) RH High-Speed Cat No. Cat No.
1-1/8" - 8 (12UN) 49215
1-1/4" - 8 49220 (UNC) (UNF)
1-3/8" - 8 49225
1-1/2" - 8 49230 RH Rebar Size – RH Rebar Size –
1-3/4" - 8 49240 High-Speed TPI High-Speed TPI
1-7/8" - 8 49245
2" - 8 49250 34077 3/8"-16 85850 1"-8
2" - 12 49345 34082 1/2"-13 79120 1-1/8"-7
34087 5/8"-11 85855 1-3/8"-6
34092 3/4"-10
Beveling Dies For beveling pipe prior to welding. Set of beveling dies.
Consists of three guide segments and one cutting segment.
Catalog No. Description Pipe Size Used in Die Head
(in.) (in.)
52192 37-1/2º Bevel Die Set 1/2-3/4 12-20 Universal
50960 37-1/2º Bevel Die Set 1-2 25-50 Universal
52202 45º Bevel Die Set 1/2-3/4 12-20 Universal
52965 45º Bevel Die Set 1-2 25-50 Universal
Cut Grooving Dies For cut groove pipe for mechanical type couplings,
consult chart for sizes and die heads information.
Pipe Size
Catalog No. Description (in.) (in.) Used in Die Head
52217 Grooving Die Set 1/2-3/4 12-20 Universal
50985 Grooving Die Set 1-2 25-50 Universal
134
#1224 ThrMeaacdhiinnge
#1224 Threading Machine
CAPACITIES
• Pipe: 1/4"- 4" (4"- 6" with #141 and #161 Geared Threader)
• Bolt: 1/4"- 2"
FEATURES
• Threads 1/4"-2" pipe at 36 RPM and 2-1/2"- 4" at 12 RPM
• The 1224 threads a wide range of pipe including black, galvanized and
plastic-coated pipe, together with stainless steel, IMC and heavy-wall
conduit, as well as rod up to 30 Rockwell C.
• 1/4"- 2" universal die head; 2-1/2"- 4" receding die head allows cutting of
tapered or straight NPT/NPSM or BSPT/BSPP threads
• Constant and proper lubrication of dies and workpiece with through-head oiling
SPECIFICATIONS
Catalog Item # Description Capacity
No.
26132 711 Universal Self-Opening R.H., NPT 1/4-2"
26142 713 Universal Quick-Opening L.H., NPT 1/4-2"
26152 714 Receding Self-Opening R.H., NPT 2-1/2-4"
26162 541 Quick-Opening Bolt L.H./R.H. 1/4-1"
26167 542 Quick-Opening Bolt L.H./R.H. 1-1/8-2"
55447 725 Cut-Grooving Die Head 2-1/4-4"
2-1/2–3-1/2"
57497 2-1/2”-3-1/2” Grooving Die Set
57507 2-1/2”-3-1/2” Grooving Bit Only
57492 4” Grooving Die Set 4"
3/4–4"
57502 4” Grooving Bit Only
55452 766 Blade Type Cutter
58712 Cut-Off Tool Bit
Note: Die Heads do not include dies. All Die Heads are through-head oiling.
ACCESSORIES
Catalog Item # Description
No.
26212 764 1/4"-4" Wheel-Type Cutter
26217 744 1/4"-4" Blade-Type Reamer
34577 1/4"-4" Reamer Blade
26187 819 Jaw Insert and Roll Set for PE-Coated Pipe
51005 Nipple Chuck 1/2" - 2" NPT
34157 419 Nipple Chuck 2-1/2" NPT
34162 419 Nipple Chuck 3" NPT
34167 419 Nipple Chuck 4" NPT
61122 840A Universal Drive Shaft
26707 Gear Grease (1224 & 1822)
877.446.4352 www.superiortoolrental.com www.SwupweriworT.moolRidenltaaln.cdomto8o77l.-c44o6m-4352 135
#M1ac2h2in4eTAhcrceeasdsionrgies
Pipe Dies for use in UniversaI Die Heads
(Nos. 504A, 711, 713, 811A, 815A, 816, 817, and 842)
Nominal Pipe Size - Threads Per Inch (NPT)
Die Material or Type 1/8"-27 1/4"-3/8"-18 1/2"-3/4"-14 1"-2"-11-1/2
High-Speed RH 47755 47760 47765 47770
47780 47785 47790
H.S. For Stainless Steel RH 47775
SPECIFICATIONS
Catalog Description Capacity
No. 2-1/2"- 4
26192 1224 H.S. Dies NPT
31827 1224 H.S. NPT Dies for Plastic-Coated Pipe 2-1/2"- 4
32237 1224 H.S. Dies NPT for PVC 2-1/2"- 4
33057 1224 H.S. Dies NPT for Stainless Steel 2-1/2"- 4
33072 1224 45º Beveling Dies 2-1/2"- 4
33077 1224 37-1/2º Beveling Dies 2-1/2"- 4
44992 1224 Bevel Guide Set 2-1/2"- 4
44997 1224 37-1/2º Bevel Bit Only
45002 1224 45º Bevel Bit Only
Note: NPSM threads are made with NPT dies by adjusting the die head.
136
Power TMharcehaidninesg
300 Power Threading Machine
SPECIFICATIONS
Capacity 1/8" - 2" Pipe, 2-1/2" - 4" with #141, and 4" - 6" with #161 Geared Threaders, 1/4" - 2" Rod
Motor 1/2 HP, universal, reversible motor, single-phase, 50/60 Hz, 115V
Switch Heavy-duty FOR/OFF/REV and Integral Foot Switch
Chuck RIDGID speed chuck with replaceable rocker-action jaws
Spindle Speed 38 RPM (57 RPM available)
Rear Centering Device Cam-action turns with chuck
Support Bar Heavy-duty (2)
Catalog Item # Description Spindle Speed Pipe Threading Rod Threading Max. Geared Threader Weight
No. 300 Power Drive, (rpm) Capacity (in.) Capacity (in.) Threader Capacity (in.) lb.
94
41855 300 Only 115V 50/60Hz 38 1/8 - 2 1/4 - 2 6
ACCESSORIES Description Weight lbs.
Catalog No. Item #
10883 418 Oiler with 1 Gallon Premium Thread Cutting Oil 20.5
10.5
51005 819 Nipple Chuck Complete,1/2" - 2" NPT 13
13
97065 811A 811A 1/8" - 2" NPT Die Head, Self-Operating, RH 31
6.75
97075 815A Oiler with 1 Gallon of Nu-Clear Thread Cutting Oil 8.5
42360 1206 1206 Stand 3
14.25
42365 341 Reamer
7
42370 360 Model 360 1/8" - 2" Full Floating, Self Centering Cutter 15
0.5
300 42385 312 Carriage Feed Lever 6
42575 32 #32 Transporter (for Power Drives and Tristand Vises) 10.5
12.5
46660 E-863 LH/RH Reamer Cone 13
68815 311 Carriage with No. 312 Lever
97365 - Jaw Inserts for Coated Pipe
22638 1452 Clip-On Tool Tray
68160 819 Nipple Chuck 1/2" - 2" BSPT
97070 811A BSPT Die Head Quick-Open R.H.
97080 815A 815A 1/8" - 2" BSPT Self-Opening Die Head
Oiler
SPECIFICATIONS
Catalog No. Item # Description Weight lb. Chip Pan Dia. Chip Pan Depth Hose Length Capacity
10883 Oiler w/1 Gal. 14-1/4" 8-3/8" 55" 1 Gallon
418 418 Premium Thread 20.5
Cutting Oil
300 Complete Power Threading Machine 1/2 HP, Universal reversible motor, single-phase, 25-60 HZ
Heavy-duty FOR/OFF/REV and Integral Foot Switch
SPECIFICATIONS RIDGID speed chuck with replaceable rocker-action jaws
Motor 38 RPM (57 RPM available)
Switch Cam-action turns with chuck
Chuck Heavy-duty (2)
Spindle Speed
Rear Centering Device
Support Bar
Catalog Item # Description Spindle Speed Pipe Threading Rod Threading Max. Geared Threader Weight
No. 115V, 25-60 (rpm) Capacity (in.) Capacity (in.) Threader Capacity (in.) lb.
15682 300 Complete Hz (NPT) 38 1/8 - 2 1/4 - 2 6 218
ACCESSORIES Description Weight lbs.
Catalog No. Item #
Stand for 300 Power Drive 31
42360 1206 Transporter (for Power Drives and Tri-stand Vises) 14-1/4
Carriage with No. 312 Lever
42575 32 Oiler with 1 Gallon of Nu-Clear Thread Cutting Oil 15
Reamer for N0. 311 Carriage 20-1/2
68815 311 Cutter for N0. 311 Carriage
Universal Q.O. Die Head Only, Right Hand Only 7
10883 418 Self Opening Die Head Only, Right Hand Only 8-1/2
Nipple Chuck Complete, 1/2" - 2" NPT 12-1/2
42365 341 Removable Tool Tray 13-1/2
LH/RH Reamer Cone 10-1/2
42370 360
6
97065 811A 7
97075 815A
51005 819
300 Complete 22638 1452
46660 E-863
877.446.4352 www.superiortoolrental.com www.midlandtool.com 137
Roll Groovers
918-I Roll Groover STANDARD EQUIPMENT SPECIFICATIONS
918-I Roll Groover
Catalog No. Description Catalog No. 64977
36642 Footswitch, ASM. Item # 918-I
Roll Set for 8"-12" Sch 10
48405 (8" Sch 40) With Carry Case Description Roll Grooving Machine Complete
Groove Roll 2" - 6" Voltage 115
49217 Drive Roll 2" - 6" Weight (lb.) 185
51432 1" - 12" Stabilizer for
Grooving Nipples 1"- 12" Sch 10 Steel
59992 Stand, ASM 918-I
T-Handle Hex Key, 1/8" Capacity 1"- 8" Sch 40 Steel
64192 Box Wrench 2"- 6" Copper (types K, L, M & DWV)
49087 Spanner Wrench
54317 Hex Key 3/8" 1-1/2", 2-1/2" - 4" Sch 80 PVC
67192 Roll Storage Case
67197 Motor Universal 1/2 HP
53987
Motor On/Off Heavy-Duty w/ Foot Switch
Control
Speed 45 RPM (No Load)
ACCESSORIES
Catalog No. Description Weight (lb.)
48405 Roll Set for 8"-12" Sch 10 (8" Sch 40) With Carry Case 18
48407 Roll Set for 1-1/4"-1-1/2" Sch10/40 With Carry Case 10
48412 Roll Set for 1" Sch 10/40 and 1-1/4"-1-1/2" Sch 10/40 w/Carry Case 20
48417 Roll Set for 2"-6" Copper 10
59992 Roll Set for 1"-12" Stabilizer for Grooving Nipples 11
76822 Inch Diameter Tape 0.5
76827 Metric Diameter Tape 0.5
920 Roll Groover
STANDARD EQUIPMENT SPECIFICATIONS
Catalog Description Catalog No. 95782
No.
Item # 920
#32 Transporter (for Power
42575 Drives and Tristand Vises) Description 920 Roll Groover with 2" - 6" Sch.
40.8" - 12" Sch. 40 and 14" - 16" Std.
920 Training Video & User Manual
Voltage 115
10843 Set of Rolls 2-6” 920
Weight (lbs) 199
10848 Set of Rolls 8-12” 920
2"-12" Sch 5, 10, & 40 Steel, Stainless Steel, Aluminum
10853 Set of Rolls 14-16” 920
14"-16" Sch 5 &10 Steel, Stainless Steel, Aluminum
18"-24" .250 Wall Steel, Stainless Steel, Aluminum
Capacity 2"-8" Sch 40 PVC
2-1/2"-4 Sch 80 PVC
2"-8" Copper (K, L, & M)
3"-8" Copper (DWV)
ACCESSORIES
Catalog Item # Description Weight
No. (lbs)
14.25
42575 32 #32 Transporter (for Power Drives and Tristand VIses) 0.5
0.5
76822 - Inch Diameter Tape 167
20
76827 - Metric Diameter Tape 21
22
96372 RJ624 RJ624 Large Diameter Pipe Stand 20
96982 - Drive & Groove Roll Set for 2"-8" Copper Tube Type K,L,M, & DMV
920 Roll Groover 96987 - Drive & Groove Roll Set for 18"-20" Sch. 10 Steel or Stainless Steel
96992 - Drive & Groove Roll Set for 22"-24" Sch. 10 Steel or Stainless Steel
96997 - Drive & Groove Roll Set for 4"-6" Sch. 40 Steel or Stainless Steel
138
258 Power Pipe Cutter Power Pipe Cutters
258-XL Power Pipe Cutter
258 258-XL
SPECIFICATIONS 258 SPECIFICATIONS 258-XL
Item # 50767 Item # 50227
Pipe Cutter Pipe Cutter
Catalog No. 2-1/2" to 8" schedule 10*/40 steel pipe Catalog No. 8" to 12" schedule 10*/40 steel pipe
Description Model 700 Power Drive (not included) Description Model 700 Power Drive (not included)
Cutting Capacity 26-30 (no load) Cutting Capacity 26-30 (no load)
105 (lbs) excludes Power Drive 140 (lbs) excludes No. 700 Power Drive
Powered Powered
Power Drive RPM Power Drive RPM
Weight Weight
STANDARD EQUIPMENT 258 & 258XL ACCESSORIES FOR 258 and 258-XL
Catalog Description Catalog Item # Description Weight
42620 Square Drive Adapter 15/16" No. (lb.)
60002 2 Ball Transfer Pipe Supports 2-1/2" to 12" -
66687 8-1/2" H-D Cutter Wheel Assembly 66687 E-258 8-1/2" H-D Cutter Wheel Assembly 13
(includes HD Cutter Wheel, hub w/pins, E258-T (includes HD Cutter Wheel, hub w/pins, cover plate)
cover plate) 50812
58222 - 8-1/2" H-D Cutter Wheel only 2
• Pump, HF32 Hydraulic Foot 54397 258PS
• RAM, Hydraulic 258 60002 8-1/2" Thin Wall Cutter Wheel Only (PVC and Steel) 2
61757 -
Transport Cart 24
Ball Transfer Pipe Support 2-1/2" to 12" 21
Pipe Roller for Beveling (for Model 258 only) 13
*Use the thin wall cutter wheel for best results.
Note: Model 258 is not recommended to cut cast iron pipe.
For Optimum wheel life always properly support the work piece with ball transfer pipe supports.
877.446.4352 www.superiortoolrental.com www.midlandtool.com 139
ProPress® Tool
#RP 340 Press Tool RP 340
FEATURES
• 270º barrel/jaw swivel
• LED-light for continued operations in no or low-light environments
• Compatible with all standard series pressing jaws and attachments from RIDGID®
• For use with copper and stainless steel tubing, steel pipe, PEX and cutting soil pipe
• Battery tool kit includes: RP 340 Press Tool, (2) 18V advanced lithium 2 batteries,
120V advanced lithium battery charger, and carrying case
• Corded tool kit includes: RP 340 Press Tool, AC power adapter and carrying case
SPECIFICATIONS Hydraulic Ram Output Operating Temp. Range Approx. Cycle Time Weight lbs
Capacity 4 seconds 8.5
7,200 lbs 15ºF to 122ºF
4" Copper & Stainless Steel with battery
1/2" - 2" (PEX)
STANDARD PRESS JAWS AND ACCESSORIES
ProPress® Standard Jaws for Copper: 1/2" – 2" Capacity
Catalog No. Description Weight (lbs.)
76652 1/2" Jaw for ProPress 4
76657 1/2" Jaw for ProPress
76662 1" Jaw for ProPress 4.25
76667 1-1/4" Jaw for ProPress 4.5
76672 1-1/2" Jaw for ProPress 4.75
76677 2" Jaw for ProPress 6.5
10
ProPress XL-C® Rings for Copper and Stainless Steel Fittings: 1/4" – 4" Capacity
Catalog No. Item # Description Weight (lbs.)
20483 XL-C 2-1/2" to 4" Rings, 40.25
20543 XL-C Actuator & Case Complete 6
20548 XL-C 2-1/2" Press Ring 9.75
20553 XL-C 11.75
21878 3" Press Ring 6.75
21103 V2 4" Press Ring 7.75
XL-C V2" Press Ring Actuator
XL-C Carrying Case Only
MegaPress® Jaws and Rings for Black Iron Pipe: 1/2" – 2" Capacity
Catalog No. Description
37958 1/2" MegaPress Jaw
37963 3/4" MegaPress Jaw
37968 1" MegaPress Jaw
37973 1-1/4" MegaPress Ring
37978 1-1/2" MegaPress Ring
37983 2" MegaPress Ring
48563 MegaPress Carrying Case
RIGID® Press Booster and Rings for Stainless Steel Fittings: 2-1/2" – 4" Capacity
FEATURES
• New RIDGID® Press Booster and Rings now press steel pipe up to 4"
• Flameless system eliminates the need for hot work permits
• Press connections can be made on a wet system
• For use with MegaPress® XL and MegaPress® XL Stainless Fittings.
Catalog No. Description Weight (lbs.)
60643 2-1/2" MegaPress Ring 5.90
60648 7.10
60653 3" MegaPress Ring 9.90
4" MegaPress Ring
140
877.446.4352 www.superiortoolrental.com www.midlandtool.com 141
Beveling Band MADE INTHE USA
#206A Band Beveling Crawler #206A
FEATURES BEVELING BAND SPECIFICATIONS
• Operating attachment available in manual or motorized
• Beveling bands available for pipe sizes 6" and larger
• Provides smooth, accurate cuts and bevels
• Perfect for tight spaces. With a Right Angle Drive Kit,
only 6" of clearance is needed.
• Out-of-Round attachment unnecessary
• Adaptable to any beveling requirements
A Whip
B Crank Handle
C Latch Handle
D Set Screw Assembly
E Torch Holder
F Drive Wheels
G 7/16" Cap Screws
H Legs
Manual Crawler
Item # Description Weight (lbs) Dimensions (in.)
SPECIFICATIONS 206-C-6 6" Beveling Band 6 12x9x6
206-C-8 8" Beveling Band 8 14x10x10
Beveling Band Crawler 206A 206-D-10 10" Beveling Band 10 14x10x10
206-D-12 12" Beveling Band 12 18x18x10
Item # Description Weight (lbs) (in.) 206-D-14 14" Beveling Band 14 18x18x10
23x23x12 206-D-16 16" Beveling Band 16 18x18x10
206A Band Crawler with Shaft 30 206-D-18 18" Beveling Band 18 23x23x10
206-D-20 20" Beveling Band 20 23x23x10
Motorized Crawler 206-D-22 22" Beveling Band 22 23x23x10
206-D-24 24" Beveling Band 24 25x25x10
206-D-26 26" Beveling Band 26 31x31x10
206-D-28 28" Beveling Band 28 31x31x10
206-D-30 30" Beveling Band 30 31x31x10
206-D-32 32" Beveling Band 32 37x37x10
206-D-34 34" Beveling Band 34 37x37x10
206-D-36 36" Beveling Band 36 37x37x10
206-D-38 38" Beveling Band 38 43x43x10
206-D-40 40" Beveling Band 40 43x43x10
206-D-42 42" Beveling Band 42 43x43x10
206-D-44 44" Beveling Band 44 49x49x10
206-D-46 46" Beveling Band 46 49x49x10
206-D-48 48" Beveling Band 48 49x49x10
206-D-50 50" Beveling Band 50 52x54x10
206-D-52 52" Beveling Band 52 54x56x10
206-D-54 54" Beveling Band 54 56x58x10
206-D-56 56" Beveling Band 56 58x60x10
206-D-58 58" Beveling Band 58 60x62x10
206-D-60 60" Beveling Band 60 62x64x10
SPECIFICATIONS
Motorized Kit
Item # Variable Speeds Operates Power
206A Increased speed control Forward or AC or DC
allows flame Reverse
for plasma cutting
142
Torch Beveling
Standard Torch Beveling Machine
FEATURES
Every ring gear and saddle are precisely machined and calibrated to ±
.025 in concentricity and ± .015 in squareness. The standard rear-mounted
short saddle aids cutting and beveling in tight locations, while allowing
precise back-beveling operations.
H&M’s unique “split horseshoe” design permits easy placement over pipe
sections. A quick-operating boomer assembly securely locks the machine
to the pipe for an entire 360-degree rotation. No repositioning is ever
needed! H&M’s Cuboid Spacer System keeps the spacers on the machine
to minimize downtime.
H&M Pipe Beveling Machines save weld prep time and money compared
to hand cutting. With easy-to-follow manuals and a few minutes of
instruction, any operator can easily make accurate cuts and bevels.
HOW FAST? For example when using the No. 3 Standard Beveling
Machine, a 20" pipe can be cut and beveled in about four minutes!
Torch Beveling Machine Specifications Storage Box Specifications
Item # Standard Pipe Sizes Weight (lbs) Box Model No. Item # Weight (lbs)
No. 0 2", 2.5", 3" and 4" 9.50 0 Storage Box BOX00 7
No. 1 3", 4", 6" and 8" 18 1 Storage Box BOX01 11
No. 2 6", 7", 8" and 12" 27 2 Storage Box BOX02 18
No. 3 12", 14", 16" and 18" 55 3 Storage Box BOX03 32
No. 4 20", 22", 24" and 26" 81 4 Storage Box BOX04 39
No. 30 24", 26", 28" and 30" 92 30 Storage Box BOX30 42
No. 5 30", 32", 34" and 36" 145 5 Storage Box BOX05 73
877.446.4352 www.superiortoolrental.com www.midlandtool.com 143
Electrical Construction Tools
SCHEDULE A VISIT
Greenlee on-site demonstrations and trainings are available.
Contact your sales or rental representative for more information
and/or scheduling.
Cable Pulling
Smart Pull FG01
FEATURES Smart Pull FG01
What happens when cable is over stressed during a pull?
• Diminished transmission capabilities
• Potential fire hazard
• Rework and liability for the contractor
The G-Series Smart is:
• FASTER: Instant early warning alerts allows contractor to take timely
action, avoiding rework.
• SAFER: Reduce liability by recording information with accuracy ensuring
a healthy pull and peace of mind for the contractor
• EASIER: Wirelessly monitor force, speed and distance through the entire pull
SPECIFICATIONS Used for measuring pulling force, distance 5 and speed during cable pull
Application Up to 5aH Makita battery
Power Supply Up to 10,000 lbs.
Pulling Force Up to 7/8" Diameter Double braided rope
Pulling Rope 18V
Voltage Rating 128MB
Onboard Memory 34.2 lbs without Carrying Case, 52.2 lbs with Carrying Case
Weight +/- 2%
Accuracy L 25-1/2" H 9-1/2" W 8"
Dimensions
144
Cable Pulling
Tugger® Cable Puller: 2,000 lb. Turbo™ Cable Puller: 6,000 lb.
FEATURES FEATURES
• Up to 60% Faster compared to competition
• 3X faster set-up than
competition - no loose pieces • Setup in less than 60 seconds
• 20% faster than competition • No loose pieces, allowing quick
• 25% stronger than competition changeover for easy transport
• Clamp easily adjusts for different
• No adapter needed - easily clamp
sizes of conduit conduit in seconds
• Right angle sheave safely keeps
• Dual capstans increase pulling
operators out of direct line of pulls speeds and maximize efficiency
• Portable handle and wheels for
• Two speed motor specially designed
increased mobility around jobsites for 6,000 lb loads
• Change tail length, pull direction,
• Circuit breaker monitor for safe auto
and angle of pull with ease shutoff and extend motor life
• Can hook on the back of a truck hitch
• Customized motor with circuit • Force indicator prevents damage
to puller
breaker specifically designed for
cable pulling • Built-in dolly for fast and easy transport
• Ergonomic design eliminates heavy
lifting during setup
#G3 • Right-angle sheave allows the #G6
operator to stand out of the direct line of force
Available with pulling rope when requested Pulling Rope 1/2" x 600' pulling rope Item #456
7/8" x 1200' pulling rope Item #34138
Ultra Tugger® (UT8) Cable Puller: 8,000 lb. Ultra Tugger® 10 (UT10) Cable Puller: 10,000 lb.
SPEED SPEED
• 8,000 lbs. pulling force to • 2-Speed gear-motor enable
handle most pulling jobs. 20% faster pulling time
VERSATILE • Shift from high-speed/low-load
pulling to low-speed/high-load
• Available with Mobile pulling with a simple double-tap
VersiBoom for less than motion on the foot-pedal
2 minute, one person
set-up, & 20' tall VERSATILE
• Available with floor mount • Available with Mobile VersiBoom
& chain mount for tighter for less than 2 minute, one
spaces person set-up, & 20' tall
#6806 • Available with floor mount &
chain mount for tighter spaces
HEAVY DUTY
• Customized gear motor
specifically for heavy-duty
cable pulling application
and meet UL & cUL
safety requirements
#6906
877.446.4352 www.superiortoolrental.com www.midlandtool.com 145
Cable Bending
#555C Classic Electric Bender for Conduit & Pipe #555C Series Electric Bender Shoe Guide
VERSATILE #23008 RIGID Shoe Group #28008
#23803
• Bend 1/2" to 2" RIGID/IMC/EMT SPECIFICATIONS
on 2 shoes 1/2" - 4-1/4", 3/4" - 5-7/16"
MOBILE Bend Radius 1" - 6-15/16", 1-1/4" - 8-3/4"
1-1/2" - 8-1/4", 2"- 9"
• Lightweight, compact design for
easy job-site portability Capacity 1/2" - 2" Rigid Shoe
RELIABLE #23803 EMT Shoe Group
• Greenlee’s classic “triple-nickel” SPECIFICATIONS
electric bender, features simple 1/2" - 4-1/4", 3/4" - 5-7/16"
relay controls for easy field repairs
Bend Radius 1" - 6-15/16", 1-1/4" - 8-3/4"
#555C 1-1/2" - 8-1/4", 2"- 9"
Capacity 1/2" - 2" EMT
#00573 PVC Shoe Group
SPECIFICATIONS
Application For 37279 40 Mil PVC
Coated Rigid 1/2" - 2.000" Shoe Group
Capacity 1/2" - 1-1/4" Ridgid PVC Conduit
#00573
#854DX Electric Bender #854DX
VERSATILE
• 1 shoe bends 1/2" to 2" EMT, IMC and Rigid conduit
• Simple switching between vertical and horizontal
bending configurations
ACCURATE
• Absolute encoder stops bending at precise angles
• Digital pendant sets angle and monitors process
RELIABLE
• Solid state electronics rated for 1,000,000+ bends
• Solid state system eliminates arcing and prevents damage
from temporary power loss
#881-MBT Mobile Bending Table
EFFICIENT
• Save one hour with every move
• All components pin to the table, reducing component
loss allowing convenient transport from site to site
MOBILE
• Minimize material handling and repetitive lifting with
on-board storage
• Fits through standard height doors 36" wide
ERGONOMIC
• Waist-height bending for operator comfort
#881-MBT
146
6 Ton Crimper Quad Flip Termination & Knockout
12 Ton Crimper Indent
#EK6FTLX11 #EK12IDLX11
SPECIFICATIONS SPECIFICATIONS
Type Dieless style crimper Type Dieless style crimper
Application 6 Ton crimping Application 12 Ton crimping
Standard C/US UL Listed Standard C/US UL Listed
Wire Size 6 AWG - 750 kcmil Cu &AI Wire Size 4 AWG - 1000 kcmil Cu / 6 AWG - 1000 kcmil AI
Length 14.875" Length 16.5"
Crimping Force 12,400 lbs Crimping Force 12,400 lbs
Crimping Capacity 750 Kcmil Crimping Capacity 1000 Kcmil
Connector Type Color-coded lugs and splices Connector Type Color-coded lugs and splices
Handle Type Pistol style with over molded rubber grip Handle Type Pistol style with over molded rubber grip
Cable Cutter 11 Ton INTELL-Punch with Case
#LS100XB
#ESG50LX11 SPECIFICATIONS
SPECIFICATIONS Application Punch conduit size holes in mild steel,
stainless steel, aluminum, fiberglass & plastic
Type Capacity 11 Ton
Application Gillotine style cutter Capacity Mild Steel 4" conduit up to 10 guage, 6" up to 14 guage
Cutting Edge Copper, aluminum Capacity S.S. 4" conduit up to 10 guage
Cutting Range Hard metal, steel Minimum Pilot Hole 1/2", 7/8", 1-1/8"
Jaw Size 2,000" diameter aluminum or copper cable Operation Single-Trigger
Length 1.97" Operation Type Battery-Hydraulic
Handle Type 15.75" Conduit & Pipe Size 1/2" to 6"
Finish Pistol style with over molded rubber grip Weight 15.11 lbs
Chrome
877.446.4352 www.superiortoolrental.com www.midlandtool.com 147
Bending and Threading Cart 555®CX
Greenlee® Workhorse Bending and Threading Cart #300
FEATURES
• Greenlee 555CX Electric Bender
• Rigid #300 Pipe Threading Machine
• Document holder
• Pipe supports
• Lockable storage
• Open storage
• Fork pockets on 3 sides
• 8" casters for easy mobility
• Bend check to measure conduit and verify 90-degree bends
• Ergonomic handle height reduces lower back strain
WORKSTATION SPECIFICATIONS Mounted
Chain Vise
Capacity 2000 lbs
Casters 2 locking swivel, 2 rigid
Caster Size 8”
Threader Mounting Brackets Yes
Dimensions L 74" H 28.5" D 32"
Weight 1,120 lbs
#300 Compact Threading Machine Specifications 555®CX Electric Bender
Pipe Bolt Motor Control Chuck Oiling System • Decrease down time with solid state electronics
Capacity Capacity • 555®CX is a completely reengineered
Heavy-duty rotary Hammewr-type Through-the-head, with
forward/off/reverse with replaceable, integral oil reservoir with 555®C with a more rugged exterior
1/8" - 2" 1/4" - 2" and integral foot rocker-action self-priming, constant-flow
CAPABILITY
switch jaw inserts gerotor pump • Bend 1/2" to 2" RIGID/IMC/EMT on 2 shoes
#300 Threading Machine NPT Die Heads
Catalog Item # Description How Thread Oil Thru Dies Pipe Weight
No. Opened Direction Head Used Capacity (lbs.) #555C Series Electric Bender Shoe Guide
42047 500A Mono Q.O RH Yes Mono 1/8" 6.75
42052 500A Mono Q.O RH Yes Mono 1/6" 7 #23008 RIGID Shoe Group
42057 500A Mono Q.O RH Yes Mono 3/8" 7
42062 500A Mono Q.O RH Yes Mono 1/2" 7.25 SPECIFICATIONS
42067 500A Mono Q.O RH Yes Mono 3/4" 7.25
42072 500A Mono Q.O RH Yes Mono 1" 8 1/2" - 4-1/4", 3/4" - 5-7/16"
42077 500A Mono Q.O RH Yes Mono 1-1/4" 8 Bend Radius 1" - 6-15/16", 1-1/4" - 8-3/4"
42082 500A Mono Q.O RH Yes Mono 1-1/2" 8.5 Capacity 1-1/2" - 8-1/4", 2"- 9"
42087 500A Mono Q.O RH Yes Mono 2" 8.5 1/2" - 2" Rigid Shoe
Die Heads Description Weight #23803 EMT Shoe Group #28008
(lbs) #23803
Catalog Item # 1/8" - 3/4" semi-Automatic Die Head 13 SPECIFICATIONS #00573
No. Bolt Die Head Quick-Open R.H./L.H. 1/4" -1" 7.5 1/2" - 4-1/4", 3/4" - 5-7/16"
Bolt Die Head Quick-Open R.H./L.H. 1-1/8" -2" 9
84537 816 NPT Die Head Quick-Open R.H. 13 Bend Radius 1" - 6-15/16", 1-1/4" - 8-3/4"
97045 531 815A 1/8" - 2" NPT Die Head, Self-Opening, RH 13 1-1/2" - 8-1/4", 2"- 9"
97050 532 1/2" - 2" Semi-Automatic Die Head 13
97065 811A 815A 1/8" - 2” NPT Die Head, Self-Opening, RH 12.5 Capacity 1/2" - 2" EMT
97075 815A 815A 1/8" - 2" BSPT Self-Opening Die Head 13
84532 817 #00573 PVC Shoe Group
97070 811A
97080 815A
Accessories SPECIFICATIONS
Catalog No. Item # Description Weight (lbs.) Application For 37279 40 Mil PVC
51005 819 Nipple Chuck Complete, 1/2" - 2" NPT 10.5 Coated Rigid 1/2" - 2.000" Shoe Group
67662 - 30
68160 819 Adapter Bracket for 300 Compact 10.5 Capacity 1/2" - 1-1/4" Ridgid PVC Conduit
Nipple Chuck 1/2" - 2" BSPT
148
Material Handling
2" to 24" Beam Pipe Clamp with 2 Rollers PN 2110
FEATURES
• Roller maintains positioning at center of beam via:
dual side clamp mechanisms on each side; 4 locking bolts;
and adjustable locking clamps on both sides.
• Safety harness is included with rental, and must be
used while operating
• Carry handles on sides of unit
• Powder coated safety red
• Safety harness included
• Safety harness must be used when in operation
(2) 6" Rollers
6" H
9" H
21" W
SPECIFICATIONS
Pipe Capacity 2" – 24"
Weight Capacity 2,500 lbs
Dimensions L 17" W21" H6" (bottom of roller) x H 9" (top of roller)
Weight 59 lbs
Portability Carry handles
Material Urethane over steel wheels with sealed bearings
Color Powder coated safety red
Number of Rollers 2
877.446.4352 www.superiortoolrental.com www.midlandtool.com 149
Machinery Rollers
Light Duty Series (Riggers Kits and Sets Capacities: 3 and 8 Tons)
Kit / Set Roller Capacity Kit Product Set Product Kit / Set Includes (All Kits include steel cases) Weight
Capacity (Tons) (Tons) Number Number Steel Case Kit Box KB-D1: 16" x 12.375" x 4.44" lbs.
- (4) 0.75-SP Rollers, (2) 3-KH Handles 55
3 0.75 KRS-3-4S 52
55
3 0.75 - RS-3-45 (4) 0.75-SP Rollers, (2) 3-KH Handles 52
85
3 0.75 KRS-3-2S/2R - (2) 0.75-SP Rollers, (2) 0.75-RP Rollers, (2) 3-KH Handles 76
85
3 0.75 KRS-3-4S RS-3-2S/2R (2) 0.75-SP Rollers, (2) 0.75-RP Rollers, (2) 3-KH Handles 76
8 2 KRS-8-4S - (4) 2-SP Rollers, (2) 8-KH Handles Weight
lbs.
8 2 - RS-8-4S (4) 2-SP Rollers, (2) 8-KH Handles 203
156
8 2 KRS-8-2S/2R - (2) 2-SP Rollers, (2) 2-RP Rollers, (2) 8-KH Handles 203
156
8 2 - RS-8-2S/2R (2) 2-SP Rollers, (2) 2-RP Rollers, (2) 8-KH Handles 215
172
FT Series (Deluxe Kit Capacites: 15-60 Tons – Complete Set Capacities: 15-200 Tons) 215
172
Kit / Set Roller Capacity Kit Product Set Product Kit / Set Includes (All Kits include steel cases) 219
Capacity (Tons) (Tons) Number Number Steel Case Kit Box KD-D2: 27.75" x 14.75" x 9.63" 176
- (4) 3.75-SLP Rollers, (2) KDH48F Handles 219
15 3.75 KRS-15-SLP (4) 3.75-SLP Rollers, (2) H36F 36" Handles 176
RS-15-SLP (4) 3.75-SLD Rollers, (4) P-1 Preload Pads, (2) KDH48F Handles 255
15 3.75 - - 4) 3.75-SLD Rollers, (4) P-1 Preload Pads, (2) H36F 36" Handles 212
(4) 7.5-SLP Rollers, (2) KDH48F Handles 259
15 3.75 KRS-15-SLD RS-15-SLD (4) 7.5-SLP Rollers, (2) H48F 48" Handles 216
- (4) 7.5-SLD Rollers, (4) P-1 Preload Pads, (2) KDH48F Handles 542
15 3.75 - (4) 7.5-SLD Rollers, (4) P-1 Preload Pads, (2) H48F 48" Handles 540
RS-30-SLP (4) 10-SLP Rollers, (2) KDH48F Kit Size Handles 834
30 7.5 KRS-30-SLP - (4) 10-SLP Rollers, (2) H48F 48" Handles 848
(4) 10-SLD Rollers, (4) P-1 Preload Pads, (2) KDH48F Handles
30 7.5 - RS-30-SLD (4) 10-SLD Rollers, (4) P-1 Preload Pads, (2) H48F 48" Handles
- (4) 15-SLP Rollers, (2) KDH48F Kit Size Handles
30 7.5 KRS-30-SLD (4) 15-SLP Rollers, (2) H48F 48" Handles
RS-40-SLP (4) 15-SLD Rollers, (4) P-1 Preload Pads, (2) KDH48F Handles
30 7.5 - - (4) 15-SLD Rollers, (4) P-1 Preload Pads, (2) H48F 48" Handles
(4) 30-SLP Rollers, (2) H60F 60" Handles
40 10 KRS-40-SLP RS-40-SLD (4) 30-SLD Rollers, (2) P-2 Preload Pads, (2) H60F 60" Handles
- (4) 50-SLP Rollers, (2) H60F 60" Handles
40 10 - (4) 50-SLD Rollers, (4) P-2 Preload Pads, (2) H60F 60" Handles
RS-60-SLP
40 10 KRS-40-SLD -
40 10 - RS-60-SLD
RS-120-SLP
60 15 KRS-60-SLP RS-120-SLD
RS-200-SLP
60 15 - RS-200-SLD
60 15 KRS-60-SLD
60 15 -
120 30 KRS-60-SLP
120 30 -
200 50 KRS-60-SLD
200 50 -
150
The words you are searching are inside this book. To get more targeted content, please make full-text search by clicking here.
Discover the best professional documents and content resources in AnyFlip Document Base.
Search