TECMOR English Catalogue 2017

Benders, Cutters, Combined, Stirrup
and Spiral Machines for Rebar Industry

2017 EDITION

2 COMPANY HISTORY

TECMOR was founded in 1960 by the three brothers Mora
in Gavardo, a town at North-East of Brescia, Italy, occupying
a small factory of 100 sqm., with the aim of serving
companies in the area by doing precision engineering work.
After developing third-party projects, in 1968 Tecmor realised
the first prototype of their bending machine, the evolution
of which was presented at the SAIE fair in Bologna in 1970:
the first machine was the PFT 35/28 combined.
The interest was immediate both in Italy and abroad: the
first order was from Belgium and began the expansion in
international markets. The production increased and Tecmor
needed more space: next to the initial factory it was
constructed the second production plant of 1,500 sqm.,
from where in 1985 the first machine with single-block cast,
an innovation that made the TECMOR machines stronger
than the competition; also redesigned were the gears
systems, allowing the machines to be equipped with less
powerful engines, less energy needed for the same
performance.
In 1980 TECMOR was already present in South America,
North Africa, the Middle East, the brand was beginning to
establish itself as synonymous with quality while maintaining
reasonable prices compared to other European producers.
In 1982 was added another 3.500 sqm. of factory space,
raising production capacity to more than 2,000 pieces a
year.
In 1987 was introduced the brand SEIM, a line of lighter
machines to serve the customers that operate on job sites,

3 INDEX

PROFESSIONAL FACTORY LINE

BENDERS S - 4S TYPE PAGE 4
CUTTERS C TYPE PAGE 6
STIRRUP · SPIRAL PAGE 7

JOB SITE LINE · HIGH CAPACITY

BENDERS N TYPE PAGE 8
CUTTERS C TYPE PAGE 9
COMBINED N TYPE PAGE 10

combining practicality and convenience: the machines were FITTINGS AND ACCESSORIES
immediately appreciated and become part of the company's
offer. FITTINGS UPON REQUEST PAGE 11
In 1989 was realised the first spiral machine, still one of
the most versatile machines and sold by TECMOR around
the world, and also was designed the new work-table for
the top range machines PF45 and PF55, with the introduction
of 2 and 4 saddles with a new rotation disk.

TECMOR entered the new millennium with a new
technological proposal, in 2001 the introduction of the single
phase motor with inverter to allow the machines to be used
with domestic voltage. Tecmor continues the international
expansion of the company through partnerships with national
distributors, which still allow the company to be present in
5 continents, recognized market leader in electric bending
and cutting machines for the industry reinforced concrete
bars.

4 PROFESSIONAL FACTORY LINE

S TYPE BENDERS

The TECMOR S Type benders have been
built to meet the needs of professional
customers, such as those customers who
have to produce significant amounts of
finished bars and cages in loco at the factory
and then transport the material to the
construction site.
The work-table is designed to be used from
both sides, provided with 2 saddles along
the entire length of the work surface to allow
the bending from 4 different positions. This
is the only machine suitable for bending
angles as required by the regulations in
force.

Recommended fittings
• Electronic control panel 10/50
• Memory panel 9x9
• Speed variator
(included for PF45 S / PF55 S / PF62 S)
• Tool set for stirrup bending
• Double foot pedal
• Spiral device S18

4S TYPE BENDERS

The TECMOR 4S Type differs by the
presence of 4 saddles on the working table,
the dimension and the greater weight,
synonymous of solidity and versatility, for
every type of bending in large amounts of
bars.
These machines are tested to work full day
in all weather conditions, without ever having
to stop production.

Recommended fittings
• Electronic control panel 10/50
• Memory panel 9x9
• Speed variator
(included for PF45-4S / PF55-4S / PF62-4S)
• Double foot pedal
• Bending arm

TECMOR TYPE Ø Max. rpm. N° bars Ø max. Mot. Size cm. Weight Kg.
650 N/mm Kw
PF 40-S Ø34 8 1
PF 45-S Ø38 7/14 2 34
PF 55-S Ø46 5/12 3
PF 62-S Ø52 2/7 1 24 2,2 110 x 76 x 86 h 380
2
TECMOR TYPE 3 18
1
PF 40-4S 2 38/34
PF 45-4S 3
PF 55-4S 1 26/24 4 114 x 90 x 88 h 680
PF 62-4S 2
3 22/20

46/36

32/26 5,5 114 x 90 x 88 h 800

26/22

52/46

38/34 7,5 114 x 90 x 88 h 900

30/28

Ø Max. rpm. N° bars Ø max. Mot. Size cm. Weight Kg.
650 N/mm Kw
Ø34 8 1
Ø38 7/14 2 34
Ø46 5/12 3
Ø52 2/7 1 24 2,2 120 x 76 x 86 h 420
2
3 18
1
2 38/34
3
1 26/24 4 144 x 85 x 88 h 780
2
3 22/20

46/36

32/26 5,5 154 x 90 x 88 h 900

26/22

52/46

38/34 7,5 154 x 90 x 88 h 990

30/28

EQUIPMENT PF 40S / 4S = Ø 25x1 - Ø 48x4
PF 45S / 4S = Ø 35x1 - Ø 42x4
PF40S / 4S = Ø 68x4 - Ø 87x2 - Ø 130x1 PF 55S / 4S = Ø 35x1 - Ø 42x4
PF45S / 4S = Ø 62x4 - Ø 87x2 - Ø 130x1 - Ø 192x1 PF 62S / 4S = Ø 35x1 - Ø 50x4
PF55S / 4S = Ø 62x4 - Ø 87x2 - Ø 130x1 - Ø 192x1 - Ø 240x1 PINS
PF62S / 4S = Ø 69x4 - Ø 95x2 - Ø 130x1 - Ø 192x1 - Ø 240x1
MANDRINS

Square for small diameters Wrenchs Adaptor plug

6 PROFESSIONAL FACTORY LINE

C TYPE CUTTERS

The TECMOR C Type cutters are produced
by a single-block cast, not welded and no
carpentry parts, which guarantees a unique
solidity which is not reflected in the industry.

The gears are hardened with wear-resistant
steel with automatic lubrication, with the
moving part hardened and rectified steel.

Furthermore, the blades are treated with a
special hardened steel, so they can be used
on all 4 sides and allow a precise cut of all
bars diameter.
These cutters can work hard without
showing any signs of dysfunction to be
suitable for professional use.

Recommended fittings
• Remote electrical foot pedal.

TECMOR TYPE Ø Max. rpm. N° bars Ø max. Mot. Size cm. Weight Kg.
650 N/mm Kw
C 40
C 45 Ø 3 4 60 1 34 3 60 x 100 x 85 h 470
C 55 Ø 3 8 50 2 24
C 62 Ø 4 6 50 3 18 3 110 x 65 x 100 h 650
Ø 52 50 1 38
2 26 4 130 x 69 x 110 h 850
3 22
1 46 5,5 130 x 69 x 110 h 940
2 32
3 30
1 52
2 38
3 30

EQUIPMENT

Allen Belt Wrench Adaptor plug

7 PROFESSIONAL FACTORY LINE

STIRRUP SPIRAL

ST 24 SP 30

Based on experience, Tecmor created this Stirrup machines Using the experience gained with the benders, TECMOR
which produces a high quantity of products with extreme produced Spiral SP Type which has became one of the
precision in a limited time. best-sellers of our production, because of its versatility and
Equipped with a variable speed drive and adjustable tool value for money. You can produce angles and spirals using
for producing all kinds of stirrup, this machine can make bar up to 32 mm. diameter. These machines are suitable
the difference in your production line. for supporting column and arch production.

TECMOR TYPE Ø Max. rpm. N° bars Ø max. Mot. Size cm. Weight Kg.
650 N/mm Kw
ST 24 Ø20 1 76 x 81 x 86 h 240
92 20 1,5
16
3 14
1 16
18 2 14
3 12

SP 22 Ø22 20 1 22 0,75 76 x 62 x 94 h 200

SP 30 Ø32 20/30 1 32 1,8 90 x 70 x 94 h 320

EQUIPMENT ST 24
ST 24 Pin
1x Ø 48
1x Ø 55

Allen Wrench Adaptor plug

8 JOB SITE LINE · HIGH CAPACITY

N TYPE BENDERS

The Tecmor benders N type are built for
heavy usage on the construction site, where
they will stay for months bending important
amount of bars. Realised with the same
concept of S series for solidity, they have
a wider disk, rotating in two directions,
clockwise and counter clockwise, to suit
every bending requirement.
The crankcase is cast, without welded parts,
to ensure strength and durability under
stress, the work plan also includes 2 half
saddles to facilitate precision regulations,
favouring the bending when necessary.
The work table is hinged and can be opened
for cleaning and inspection.
These benders meet the EU standards
which require a specific ratio between bar
diameter and mandrins size.

Recommended fittings
• Tool set for stirrup bending • Memory panel 9x9
• Speed variator • Spiral device S18
• Double foot pedal

According to the European regulations

TECMOR TYPE Ø Max. rpm. N° bars Ø max. Mot. Size cm. Weight Kg.
650 N/mm Kw
PF 32N Ø28 1 76 x 81 x 86 h 270
PF 36N Ø32 10 2 28 1,5
PF 44N Ø36 20 1,5 76 x 81 x 86 h 290
PF 48N Ø40 3 16 2,2
1 32 3 80 x 89 x 86 h 390
82 20
3 16 80 x 89 x 86 h 410
1 36
82 26
3 20
1 40
72 28
3 24

EQUIPMENT PF32N = Ø 24x1 - Ø 36x4 Complete Square
PF32N = Ø 48x2 - Ø 56x2 - Ø 64x1 - Ø 90x1 - Ø 126x1 PF36N = Ø 24x1 - Ø 36x3
PF36N = Ø 48x2 - Ø 56x2 - Ø 64x1 - Ø 90x1 - Ø 126x1 - Ø 143x1 PF44N = Ø 24x1 - Ø 38x2 - Ø 48x2
PF44N = Ø 56x2 - Ø 64x1 - Ø 68x1 - Ø 90x1 - Ø 126x1 - Ø 143x1 PF48N = Ø 24x1 - Ø 38x2 - Ø 48x2
PF48N = Ø 56x2 - Ø 64x1 - Ø 68x1 - Ø 90x1 - Ø 126x1 - Ø 143x1 PINS

MANDRINS

9 JOB SITE LINE · HIGH CAPACITY

C TYPE CUTTERS

These cutters are constructed with the same
characteristics as professional C Series,
they have single-block cast, hardened steel
in every part.
The dimensions are adapted to a smaller
bar diameter.
The size of these machines are smaller,
suitable to move with ease on the
construction site.

Recommended fittings
• Remote electrical foot pedal.

According to the European regulations

TECMOR TYPE Ø Max. rpm. N° bars Ø max. Mot. Size cm. Weight Kg.
650 N/mm Kw
C 24 Ø20 1 65 x 40 x 61 h 110
C 30 Ø26 110 2 20 1,1
C 36 Ø32 16 2,2 45 x 85 x 70 h 240
3 14 2,2
1 26 53 x 92 x 72 h 350
110 2 18
3 14
1 32
100 2 20
3 16

EQUIPMENT

Allen Belt Wrench Adaptor plug

10 JOB SITE LINE · HIGH CAPACITY

N TYPE COMBINED

The Combined machines N Type for Job
Site are ideal for those who want a multi-
purpose solution, to optimize their
investment.
On these machines, with the quality to the
benders N type, is applied a cutter enabled
to cut bars of a diameters up to 28 mm.
With this machine, you can apply both
stirrup and spiral accessories, so you could
benefit from 4 applications with one
machine.
These benders also meet the EU standards
which require a specific ratio between bar
diameter and mandrins size.

Recommended fittings
• Tool set for stirrup bending
• Speed inverter
• Double foot pedal
• Electronic switchboards
• Spiral device S18

According to the European regulations

TECMOR TYPE Ø Max. rpm. N° bars Ø max. Mot. Size cm. Weight Kg.
650 N/mm Kw
PFT 32/26N Ø28 1 80 x 88 x 86 h 320
PFT 38/30N bending 92 28 1,5
20 90 x 98 x 87 h 430
Ø24 3 16 1,83
cutting 1 24
92 16
Ø32 3 14
bending 1 32
82 22
Ø28 3 16
cutting 1 28
82 18
3 14

EQUIPMENT

PFT32/26N = Ø 48x2 - Ø 56x2 - Ø 64x1 - Ø 90x1 - Ø 126x1 PFT32/26N = Ø 24x1 - Ø 36x4 PFT 32/26N
PFT38/30N = Ø 56x2 - Ø 64x1 - Ø 68x1 - Ø 90x1 - Ø 126x1 - Ø 143x1 PFT38/30N = Ø 24x1 - Ø 38x2 - Ø 48x2 Complete Square
PFT 38/30N
MANDRINS PINS Square with Pin

11 FITTINGS AND ACCESSORIES

PLEXIGLASS PROTECTION 9X9 MEMORY PANEL ELECTRONIC CONTROL PANEL 10/50
All bender and combined machines are This panel allows the operator to store up This panel is an essential accessory for
equipped with a Plexiglass protection that to 9 bending angles, speeding up incredibly professional machines, because it allows
makes sure to lock the rotation until the the work: instead of continuously inserting storage of up to 50 bending programs, each
protection is not lowered: this allows the and removing the pins from the holes along containing up to 10 memory bends. Also the
operator to work in complete safety, reducing the rotating disk, you could memorize the rotation of the disk in one direction or the
the risk of accidents. positions, allowing you to bend without taking other, will takes place automatically according
your hands off the bar, using only the electric to the memorization.
pedal.

SPEED VARIATOR DOUBLE FOOT PEDAL BENDING ARM
The speed drive is an accessory that allows The double pedal, one for the clockwise, the This accessory is dedicated to S and 4S
to vary the speed of the disk in 1 minute: other for counter clockwise, will avoid to Type Series, it allows to make bend with a
this goes from a minimum speed of 8 to a replace every time the bars and the large radius, using mandrins up to 12 times
maximum of 16 rpm. NB This accessory equipment from the work-table, such as the diameter of the steel bar.
must be ordered with the machine, it cannot mandrins and bars, and speeding up the
be applied later. execution time.

SPECIAL TOOLS FOR STIRRUP
You can transform the bender in a stirrup
machines, applying on the work-table this
simple and effective tool. It’s available for
all the benders with different sizes to fit
individual needs.

SPECIAL TOOL FOR SPIRAL S18
This device allows to transform the bender
into a spiral machine: positioned and fixed
on the work-table, this tool will make spirals

using bars up to 18 mm. diameter.

Roll benches productivity. available with or without the support of
They are 1,5 meters long each, so each pair bearings pre-greased watertight, while the
These benches are offered in couples to joins up to 3 meters of surface. tube of the bearing support is of 8 mm.
allow the balance, are indispensable
elements to allow the operator to work more The rollers are 2 per bench and are formed Minimum order: 2 pieces.
comfortably and increase by 5 segments each, they are

Benders, Cutters, Combined, Stirrup
and Spiral Machines for Rebar Industry

The machines are built in compliance with the machine guideline ECC/89/392 and
further amendments.
All the machines are equipped with the protection shown in the picture 1 at page
10.
General information and technical data are not binding and we reserve the right to
change them without any previous notice.

AUTHORISED DEALER

VIA GIOVANNI QUARENA 225/B
25085 GAVARDO · (BS) · ITALY
TEL. + 39 0365 31428
FAX + 39 0365 373030
[email protected] · www.tecmor.it