Half Circle Gasket Gal. Pipe
Part Number Length Weight
Nominal Pipe Outside
Size Diameter
15mm 21.3mm CFC-084-03 75mm 0.21kgs
15mm 21.3mm CFC-084-06 150mm 0.42 kgs
20mm 26.7mm CFC-105-03 75mm 0.22 kgs
20mm 26.7mm CFC-105-06 150mm 0.44 kgs
25mm 33.4mm CFC-132-03 75mm 0.23 kgs
25mm 33.4mm CFC-132-06 150mm 0.46 kgs
32mm 42.2mm CFC-160-03 75mm 0.24 kgs
32mm 42.2mm CFC-160-06 150mm 0.48 kgs
40mm 48.3mm CFC-190-03 75mm 0.43 kgs
40mm 48.3mm CFC-190-06 150mm 0.86 kgs
50mm 60.3mm CFC-238-03 75mm 0.44 kgs
50mm 60.3mm CFC-238-06 150mm 0.88 kgs
65mm 73.0mm CFC-300-03 75mm 0.50 kgs
65mm 73.0mm CFC-300-06 150mm 1.00 kgs
75mm 88.9mm CFC-350-03 75mm 0.53 kgs
75mm 88.9mm CFC-350-06 150mm 1.06 kgs
100mm 114.3mm CFC-450-03 75mm 0.64 kgs
100mm 114.3mm CFC-450-06 150mm 1.28 kgs
CFC and CFW Ranges - General Material Specifications:
Clamp Band - T316 Stainless Steel.
Lugs - Ductile Iron, coated.
Gasket - Nitrile, Buna N.
Bolts, nuts, washers - Carbon Steel coated.
www.australianminingservices.com.au Page 3
AMPSflo Tapped Repair Clamps.
Also in Single, Double and Multi-part tapped repair clamps provide the same
quick-and-easy fitting qualities. They are extremely useful for repairing broken
and damaged pipes at service connections or branch lines, restoring the
connection at the same time. Also efficient in cases where pipes are prone to
circumferential cracking, as they provide full circumference sealing. Stainless
Steel 316.
Grade of stainless steel, Type 316. Fully passivized after welding, to restore the
original passive state of the 316 stainless steel.
LOCKING WASHER PLATE: Locks into position for easy tightening of nuts.
LUGS: MIG-welded to receiver bar and fully passivized after welding. Leading
edge is rounded to prevent them from catching bolt bars during installation.
SHELL: 2B finish.
BOLTS: Thread-rolled for strength and coated to prevent galling. Bolts are MIG-
welded to the receiver bar and fully passivized after welding.
NUTS/WASHERS: Type 316 stainless steel.
RECEIVER BARS: TIG-welded to shell to form a strong fusion, and fully
passivized after welding.
GASKET: Nitrile rubber is specially formulated for water service incorporating
antioxidant agents to increase shelf life. All gaskets have a gridded design,
tapered ends and vulcanized armour plates for easy installation and optimum
sealing efficiency. Natural rubber is available on request.
www.australianminingservices.com.au Page 1
ARMOUR: Heavy gauge 316 stainless steel vulcanized into the gasket at the
time of moulding.
TAPPINGS: Type 316 stainless steel, BSP parallel threaded socket. ATSM
A312M, AS1722.1 Rp.
GENERAL INFORMATION:
Dimensions:
a. 150mm & 200mm length clamps, 2 x M12 bolts up to OD 104mm, M16
bolts per part OD 105mm and larger.
b. 300mm length clamps 3 x M16 bolts per part up to OD 249mm, 4 x M16
bolts per part OD250mm and larger.
c. 400mm length clamps 4 x M16 bolts per size up to OD 249mm, 5 x M16
bolts per part OD 250mm and larger.
d. 600mm length clamps 6 x M12 bolts up to OD 104mm, 6 x M16 bolts per
part up to OD 249mm, 8 x M16 bolts 250mm and larger NOTE: The
above is for single part clamps only. For Double and Multi part clamps,
the number of bolts is the same as above, but on each section/part of
the clamp.
Recommended pressure ratings:
a. Clamps to suit pipes above DN50mm - 350mm nominal size = 1.6 MPa.*
b. Clamps to suit pipes above DN375mm - 600mm nominal size = 1.2 MPa.*
c. Clamps to suit pipes above DN625mm - 900mm nominal size = 0.8 MPa.*
d. Clamps to suit pipes above DN925mm - 1200mm nominal size = 0.6 MPa.*
www.australianminingservices.com.au Page 2
Maximum Temperature: 0 - 60 degrees C.*
1. The amount of pressure that a full circle repair clamp will contain is
proportionate to the diameter of the pipe being repaired and the
amount of torque applied to the bolts. Smaller diameter repair clamps
will contain higher pressure than larger diameter repair clamps. Cleaning
and lubricating pipe/gasket, will reduce friction between the pipe
surface and sealing gasket, creating a better seal. Use soapy water or
pipe lubricate.
2. The pressure containing capability of a repair clamp is influenced by the
pipe type, the pipe surface finish, extent of damage to the pipe,
environment, service conditions and installation workmanship.
3. Recommended Clamp Lengths: The general recommendation is that the
clamp length should be four times of the damage being repaired. Where
a large section of the pipe wall is broken away, a section of thin gauge
sheet metal should be placed over the opening to provide a sealing
surface for the gasket.
4. Stainless Steel Repair Clamps do not restrain axial pipe movement.
(Suitable anchorage must be provided where pipe movement may
occur.)
5. Suitable mechanical support should be used to support the off-take
fittings.
*Pressure ratings may vary due to pipe condition and type. Refer to AS4181-
1999. Not recommended for low stiffness factor pipes below SN7500. Re-
tension clamp at Max. operating temp. AS4181-1999 up to and including
DN350mm clamps. (Specifications are subject to change without notice).
SOCKET CLAMPS, ONE PART BSP (XX)
OTHER SIZES AND LENGTHS AVAILABLE 1/2" 3/4" 1" 1 1/4" 11/2" 2" 2 1/2" 3" 4"
PART NO RANGE Size, Length, Bolts 15mm 20mm 25mm 32mm 40mm 50mm 65mm 80mm 100mm
1-0220-06 x XX 45 - 51 M12 X 150 X 2 √ √ √ √
1-0220-08 x XX 45 - 51 M12 X 200 X 2 √ √ √ √
1-0238-06 x XX 59 - 67 M12 X 150 X 2 √ √ √ √ √
1-0238-08 x XX 59 - 67 M12 X 200 X 2 √ √ √ √ √ √
1-0288-06 x XX 69 - 76 M12 X 150 X 2 √ √ √ √ √ √
1-0288-08 x XX 69 - 76 M12 X 200 X 2 √ √ √ √ √ √
1-0300-06 x XX 75 - 83 M12 X 150 X 2 √ √ √ √ √ √
1-0300-08 x XX 75 - 83 M12 X 200 X 2 √ √ √ √ √ √
www.australianminingservices.com.au Page 3
1-0350-06 x XX 85 - 95 M12 X 150 X 2 √ √ √ √ √ √
1-0350-08 x XX 85 - 95 M12 X 200 X 2 √ √ √ √ √ √
1-0375-08 x XX 95 - 104 M12 X 200 X 2 √ √ √ √ √ √
1-0375-12 x XX 95 - 104 M12 X 300 X 3 √ √ √ √ √ √ √ √
1-0440-08 x XX 104 - 113 M12 X 200 X 2 √ √ √ √ √ √
1-0440-12 x XX 104 - 113 M12 X 300 X 3 √ √ √ √ √ √ √ √
1-0445-08 x XX 110 - 120 M16 X 200 X 2 √ √ √ √ √ √
1-0445-12 x XX 110 - 120 M16 X 300 X 3 √ √ √ √ √ √ √ √
1-0450-08 x XX 113 - 123 M16 X 200 X 2 √ √ √ √ √ √
1-0450-12 x XX 113 - 123 M16 X 300 X 3 √ √ √ √ √ √ √ √
1-0480-08 x XX 121 - 130 M16 X 200 X 2 √ √ √ √ √ √
1-0480-12 x XX 121 - 130 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0500-08 x XX 126 - 136 M16 X 200 X 2 √ √ √ √ √ √
1-0500-12 x XX 126 - 136 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0520-08 x XX 130 - 140 M16 X 200 X 2 √ √ √ √ √ √
1-0520-12 x XX 130 - 140 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-135/145-08 x XX 135 - 145 M16 X 200 X 2 √ √ √ √ √ √
1-135/145-12 x XX 135 - 145 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0590-08 x XX 145 - 155 M16 X 200 X 2 √ √ √ √ √ √
1-0590-12 x XX 145 - 155 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0600-08 x XX 151 - 161 M16 X 200 X 2 √ √ √ √ √ √
1-0600-12 x XX 151 - 161 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-160/170-08 x XX 160 - 170 M16 X 200 X 2 √ √ √ √ √ √
1-160/170-12 x XX 160 - 170 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0663-08 x XX 167 - 178 M16 X 200 X 2 √ √ √ √ √ √
1-0663-12 x XX 167 - 178 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0690-08 x XX 174 - 183 M16 X 200 X 2 √ √ √ √ √ √
1-0690-12 x XX 174 - 183 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0745-08 x XX 189 - 199 M16 X 200 X 2 √ √ √ √ √ √
1-0745-12 x XX 189 - 199 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0790-08 x XX 196 - 205 M16 X 200 X 2 √ √ √ √ √ √
1-0790-12 x XX 196 - 205 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0800-08 x XX 202 - 212 M16 X 200 X 2 √ √ √ √ √ √
1-0800-12 x XX 202 - 212 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0863-08 x XX 218 - 228 M16 X 200 X 2 √ √ √ √ √ √
1-0863-12 x XX 218 - 228 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0900-08 x XX 229 - 238 M16 X 200 X 2 √ √ √ √ √ √
1-0900-12 x XX 229 - 238 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-0905-08 x XX 236 - 245 M16 X 200 X 2 √ √ √ √ √ √
1-0905-12 x XX 236 - 245 M16 X 300 X 3 √ √ √ √ √ √ √ √ √
1-1000-12 x XX 248 - 257 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1040-12 x XX 255 - 265 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1075-12 x XX 271 - 281 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1110-12 x XX 281 - 290 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1140-12 x XX 288 - 298 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1175-12 x XX 298 - 309 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1200-12 x XX 304 - 314 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1220-12 x XX 312 - 322 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1275-12 x XX 322 - 331 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1320-12 x XX 325 - 335 M16 X 300 X 4 √ √ √ √ √ √ √ √ √
1-1340-16 x XX 332 - 342 M16 X 400 X 5 √ √ √ √ √ √ √ √ √
1-1370-16 x XX 343 - 355 M16 X 400 X 5 √ √ √ √ √ √ √ √ √
1-1400-16 x XX 356 - 366 M16 X 400 X 5 √ √ √ √ √ √ √ √ √
www.australianminingservices.com.au Page 4
SOCKET CLAMPS, TWO & THREE PART BSP (XX)
OTHER SIZES AND LENGTHS AVAILABLE 1/2" 3/4" 1" 11/4" 11/2" 2" 2 1/2" 3" 4"
PART NO RANGE Size, Length, Bolts 15mm 20mm 25mm 32mm 40mm 50mm 65mm 80mm 100mm
2-250/270-16 x XX 250 - 270 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-270/290-16 x XX 270 - 290 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-290/310-16 x XX 290 - 310 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-310/330-16 x XX 310 - 330 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-330/350-16 x XX 330 - 350 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-350/370-16 x XX 350 - 370 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-370/390-16 x XX 370 - 390 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-390/410-16 x XX 390 - 410 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-420/440-16 x XX 420 - 440 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-450/470-16 x XX 450 - 470 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-480/500-16 x XX 480 - 500 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-490/510-16 x XX 490 - 510 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-510/530-16 x XX 510 - 530 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-530/550-16 x XX 530 - 550 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-550/570-16 x XX 550 - 570 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-570/590-16 x XX 570 - 590 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-580/600-16 x XX 580 - 600 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-600/620-16 x XX 600 - 620 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
2-620/640-16 x XX 620 - 640 M16 X 400 X 10 √ √ √ √ √ √ √ √ √
3-490/520-16 x XX 490 - 520 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-520/550-16 x XX 520 - 550 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-530/560-16 x XX 530 - 560 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-560/590-16 x XX 560 - 590 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-590/620-16 x XX 590 - 620 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-620/650-16 x XX 620 - 650 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-650/680-16 x XX 650 - 680 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-690/715-16 x XX 690 - 720 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-720/750-16 x XX 720 - 750 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-750/780-16 x XX 750 - 780 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
3-780/810-16 x XX 780 - 810 M16 X 400 X 15 √ √ √ √ √ √ √ √ √
www.australianminingservices.com.au Page 5
AMPSflo Tapping Saddles
AMPSflo Tapping Saddles are suitable for Duile Iron, Cast Iron, Steel, Copper,
Asbestos Cement, PVC, PE and other types of pipes, which require a
permanent BSP tapping off-take.
They eliminate the need to “cut in” an off-take, as the saddle can be installed
around the pipe without disrupting the internal flow. They are designed to fit a
range of pipe ODs in the one saddle, and they adapt to pipe orality and
irregularities. Stainless Steel 316.
Grade of stainless steel, Type 316. Fully passivized after welding, to restore the
original passive state of the 316 stainless steel.
LOCKING WASHER PLATE: SS316 Locks into position for easy tightening of
nuts.
LUGS: SS316 MIG-welded to receiver bar and fully passivized after welding.
Leading edge is rounded to prevent them from catching bolt bars during
installation.
SHELL: SS316 2B finish.
BOLTS: SS316 Thread-rolled for strength and coated to prevent galling. Bolts
are MIG-welded to the receiver bar and fully passivized after welding.
NUTS/WASHERS: SS316.
RECEIVER BARS: SS316 TIG-welded to shell to form a strong fusion, and fully
passivized after welding.
GASKET:. Nitrile, to AS1646 and AS4020. The gasket is specially designed with a
static seal and a dynamic lip seal. Also incorporated into the seal is an internal
www.australianminingservices.com.au Page 1
stainless steel retaining disc#, which prevents the seal and mat from extruding
out, under extreme internal pressure. The specially designed seal allows for
pipe outside diameter changes, caused by pressurizing and depressurizing of
the pipe.
TAPPINGS: SS316 stainless steel, DN 15mm to DN100mm BSP Rp parallel
threaded socket. Flanges SS316, standard AS4087 PN16, drilled to Table D
(DN80 & 100). Other configurations avail.
General Information:
(a) Offtake tapping DN15mm, DN20mm, and DN25mm, saddle width = 130mm.
(b) Offtake tapping DN32mm, DN40mm, and DN50mm, saddle width = 150mm.
(c) Offtake tapping DN65mm and DN80mm, saddle width = 200mm.
(d) Offtake tapping DN100mm, saddle width = 300mm.
Working Pressure Ratings:
(a) Tapping saddle to suit pipes OD75mm up to OD680mm = 1.6 MPa.*
(b) Tapping saddle to suit pipes OD680mm up to OD980mm nominal size = 1.2 MPa.*
The amount of pressure that the tapping saddles will contain is proportionate
to the diameter of the pipe. Smaller diameter tapping saddles will contain
more pressure than larger diameter tapping saddles. Suitable anchorage must
be provided where pipe movement may occur.
Suitable mechanical support should be used to support the off-take fittings
*Pressure ratings may vary due to pipe condition and type. ** Sizes DN80 to
DN300mm with 20mm to 50mm BSP only. Max. Temperature 0 - 60 degrees C.
Re-tension saddle at Max. operating temp. #Innovation Patent 2011100263 .
Specifications are subject to change without notice.
www.australianminingservices.com.au Page 2
TAPPING SADDLES STANDARD RANGE
*
Tapping Saddles are suitable for Duile Iron, Cast Iron, Hobas, Steel, Copper,
Asbestos Cement, PVC, PE, Concrete, VC, FRC, and other types of pipes, which
require a permanent BSP tapping off take.
They eliminate the need to “cut in” an off take, as the saddle can be installed
around the pipe without disrupting the internal flow and Tapped Under
Pressure.
They are designed to fit a range of pipe ODs in one saddle, and they adapt to
the pipe ovality and irregularities.
Tapping Saddles are construed from 316 Stainless Steel and have a fully line
rubber mat designed to insulate the pipe and prote it from galvanic
corrosion.
The Tapping Saddle seal is specially designed. It incorporates a static seal
and a dynamic lip seal. Also incorporated into the seal is an internal
stainless steel retaining disc#, which prevents the seal and mat from
extruding out, under extreme internal pressure.
The specially designed seal allows for pipe outside diameter changes, caused
by pressurizing and depressurizing of the pipe.
MATERIAL SPECIFICATION & STANDARDS
Tapping Saddles, are designed and manufaured under Quality Management
System, certificate to ISO9001:1994.
*AS/NZS 4129 & *AS/NZS 4793 & WSAA 12/16 for DN80 to DN300 with 20mm
to 50mm BSP only.
Body Bolts, Nuts and Washers
316 Stainless Steel 316 Stainless Steel
ASTM A240M ASTM A240M
Sealing Gasket# BSP Tapping and Flange Offtakes
Nitrile 316 Stainless Steel ATSM A312M
AS1646, AS/NZS 4020 BSP to AS1722.1, Flanges to AS/NZS
4087 (DN80 and 100)
www.australianminingservices.com.au Page 3
Working Pressure: = 1.6MPa Working Temperature: 0 to 60 Degrees C
BSP Tapping and Flanges X
DN Pipe Pipe OD Range (mm) Code (mm)*
80* 75-90 2-75/90 x X 20 & 25
80* 88-104 2-88/104 x X 20, 25, 32, 40, & 50
100* 100-118 2-100/118 x X 20, 25, 32, 40, & 50
100* 110-135 2-110/135 x X 20, 25, 32, 40, 50, & 65
125* 135-160 2-135/160 x X 20, 25, 32, 40, 50, 65, & 80
150* 160-190 2-160/190 x X 20, 25, 32, 40, 50, 65, & 80
175* 190-220 2-190/220 x X 20, 25, 32, 40, 50, 65, 80, & 100
200* 210-240 2-210/240 x X 20, 25, 32, 40, 50, 65, 80, & 100
225* 240-270 2-240/270 x X 20, 25, 32, 40, 50, 65, 80, & 100
250* 270-300 2-270/300 x X 20, 25, 32, 40, 50, 65, 80, & 100
275* 300-330 2-300/330 x X 20, 25, 32, 40, 50, 65, 80, & 100
300* 330-360 2-330/360 x X 20, 25, 32, 40, 50, 65, 80, & 100
350 360-390 2-360/390 x X 20, 25, 32, 40, 50, 65, 80, & 100
375 390-420 2-390/420 x X 20, 25, 32, 40, 50, 65, 80, & 100
400 420-450 2-420/450 x X 20, 25, 32, 40, 50, 65, 80, & 100
400/450 440-470 2-440/470 x X 20, 25, 32, 40, 50, 65, 80, & 100
400/450 470/500 2-470/500 x X 20, 25, 32, 40, 50, 65, 80, & 100
450 490-520 2-490/520 x X 20, 25, 32, 40, 50, 65, 80, & 100
500 520-550 2-520/550 x X 20, 25, 32, 40, 50, 65, 80, & 100
525 550/580 2-550/580 x X 20, 25, 32, 40, 50, 65, 80, & 100
600 590/620 2-590/620 x X 20, 25, 32, 40, 50, 65, 80, & 100
600 620/650 2-620/650 x X 20, 25, 32, 40, 50, 65, 80, & 100
600 650/680 2-650/680 x X 20, 25, 32, 40, 50, 65, 80, & 100
Clamp width BSP 20 & 25mm = 130mm. 32, 40 & 50mm = 150mm. 65 & 80 = 200mm. 100 = 300mm.
Larger pipe OD sizes are available. #Innovation
Patent 2011100263
E & O.E R15
www.australianminingservices.com.au Page 4
Couplings
Variable Pipe Couplings
Flange Adaptors
Rapid/Cascade Clamps Variable Couplings and Flange Adaptors are designed
and manufactured under Quality Management System, certificate to
ISO9001:1994. Gasket and Epoxy Powder Coating, conforms to BS6920 WRAS,
for potable water Working Pressure: 1.6MPa. Test pressure: 2.4MPa Working
Temperature: 0 to 80 Degrees C. Sizes from DN 80mm to DN300mm. Angular
deflection ±3 degrees. Fasteners 316 SS. Flange Adaptors drilled to suit AS2129
Table C, D, E, & AS4087 PN16
www.australianminingservices.com.au Page 1
COUPLINGS AND FLANGE ADAPTORS
MATERIAL SPECIFICATION & STANDARDS
Rapid/Cascade clamps Variable Couplings and Flange Adaptors are designed and manufactured under Quality Management
System, certificate to ISO9001:1994.
Gasket and Epoxy Powder Coating, conforms to BS6920 WRAS, for potable water.
Couplings and Flange Adaptor End Rings Bolts, Nuts and Washers
Ductile iron to BS 2789 Couplings = 316 Stainless Steel, 8MPa.
Grade 420/12 Flange Adaptors = Gal. Plated. 4.6MPa.
Gasket
EPDM Rubber; BS6920 for potable water.
Couplings and Flange Adapters Body Coating
Ductile iron to BS 2789 The Centre Sleeve, End Rings, and
Grade 420/12 Bodies, Epoxy Powder Coated, BS6920
for potable water.
.
Working Pressure: 1.6MPa. Test pressure: 2.4MPa Working Temperature: 0 to 80 Degrees C
Couplings and Flange Adaptors, total angular deflection of ±3 degrees.
Flange Adaptors drilled to suit AS2129 Table C, D, E, & AS4087 PN16
COUPLINGS
Pipe OD Range Bolt Size, Length, No.
Pipe Materials
Nom Code (mm) (mm)
Ductile Iron, PVC, Cast Iron, Steel, AC
80mm RV-88SS 88 - 107 M16 × 200 x 4
100mm RV-109SS Ductile Iron, PVC, Cast Iron, Steel, AC 109 - 135 M16 × 200 x 3
150mm RV-160SS Ductile Iron, PVC, Cast Iron, Steel, AC 160 - 188 M16 × 200 x 3
200mm RV-217SS PVC, Ductile Iron, Steel, Cast Iron Imp 217 - 244 M16 × 200 x 4
AC
225/250mm RV-240SS PVC, Ductile Iron, Steel, Cast Iron Imp 240 - 268 M16 × 235 x 4
AC
250mm RV-272SS PVC, Ductile Iron, Steel, Cast Iron Imp 272 - 298 M16 × 235 x 5
AC
300mm RV-315SS PVC, Ductile Iron, Steel, Cast Iron Imp 315 - 346 M16 × 300 x 5
AC
RV = Rapid Variable Couplings. S = Short Sleeve, S = SS316. Fasteners
www.australianminingservices.com.au Page 2
FLANGE ADAPTORS
Pipe OD Range Flange
Pipe Materials Connection Bolts
Nom Code (mm) Hole No. Type
Ductile Iron, PVC, Cast Iron,
100mm RFA-109G Steel, AC 109 - 135 8 M16 × 70
Ductile Iron, PVC, Cast Iron, Steel,
150mm RFA-160G AC 160 - 188 8 M16 × 80
RFA = Rapid Flange Adaptors. G = Gal. Fasteners. S = SS316 Fasteners.
E & O.E
www.australianminingservices.com.au Page 3
AMPSflo Flanged Off-Takes Clamps
Made in Single, Double and Multiband options to suit customers’
requirements. Flanged off-takes provide a full circumference seal around the
pipe, while at the same time provide a reinforcing effect to the pipe. Common
sizes are in stock. If not flanged off-takes are manufactured on request to
customers' needs and specific pipe OD, diameter of off-take and flange
specification. Standard flange designation is drilled to table C-D. Stainless Steel
316.
Grade of stainless steel, Type 316. Fully passivized after welding, to restore the
original passive state of the 316 stainless steel.
LOCKING WASHER PLATE: Locks into position for easy tightening of nuts.
LUGS: MIG-welded to receiver bar and fully passivized after welding. Leading
edge is rounded to prevent them from catching bolt bars during installation.
SHELL: 2B finish.
BOLTS: Thread-rolled for strength and coated to prevent galling. Bolts are MIG-
welded to the receiver bar and fully passivized after welding.
NUTS/WASHERS: Type 316 stainless steel.
RECEIVER BARS: TIG-welded to shell to form a strong fusion, and fully
passivized after welding.
www.australianminingservices.com.au Page 1
GASKET: Nitrile rubber is specially formulated for water service incorporating
antioxidant agents to increase shelf life. All gaskets have a gridded design,
tapered ends and vulcanized armour plates for easy installation and optimum
sealing efficiency. Natural rubber is available on request.
ARMOUR: Heavy gauge 316 stainless steel vulcanized into the gasket at the
time of moulding.
FLANGES: Type 316 stainless steel, drilled to table ‘D’, standard. Other types
are available.
GENERAL INFORMATION Dimensions:
(a) 400mm length clamps 4 x M12 bolts per size up to OD 104mm. 4 x M16
bolts per size up from OD 105mm up to OD 249mm, 5 x M16 bolts per part OD
250mm and larger.
(b) 600mm length clamps 6 x M12 bolts up to OD 104mm, 6 x M16 bolts per
part up to OD 249mm, 8 x M16 bolts per part OD 250mm and larger. NOTE:
The above is for single part clamps only. For Double and Multi part clamps, the
number of bolts is the same as above, but on each section/part of the clamp.
Recommended pressure ratings:
(a) Clamps to suit pipes above DN50mm - 350mm nominal size = 1.6 MPa.*
(b) Clamps to suit pipes above DN375mm - 600mm nominal size = 1.2 MPa.*
(c) Clamps to suit pipes above DN625mm - 900mm nominal size = 0.8 MPa.*
(d) Clamps to suit pipes above DN925mm - 1200mm nominal size = 0.6 MPa.*
Maximum Temperature: 0 - 60 degrees C.*
1. The amount of pressure that a full circle repair clamp will contain is
proportionate to the diameter of the pipe being repaired and the
www.australianminingservices.com.au Page 2
amount of torque applied to the bolts. Smaller diameter repair clamps
will contain higher pressure than larger diameter repair clamps. Cleaning
and lubricating pipe/gasket, will reduce friction between the pipe
surface and sealing gasket, creating a better seal. Use soapy water or
pipe lubricate.
2. The pressure containing capability of a repair clamp is influenced by the
pipe type, the pipe surface finish, extent of damage to the pipe,
environment, service conditions and installation workmanship.
3. Recommended Clamp Lengths: The general recommendation is that the
clamp length should be four times of the damage being repaired. Where
a large section of the pipe wall is broken away, a section of thin gauge
sheet metal should be placed over the opening to provide a sealing
surface for the gasket.
4. Stainless Steel Repair Clamps do not restrain axial pipe movement.
(Suitable anchorage must be provided where pipe movement may
occur.)
5. Suitable mechanical support should be used to support the off-take
fittings.
*Pressure ratings may vary due to pipe condition and type. Refer to AS4181-
1999. Not recommended for low stiffness factor pipes below SN7500. Re-
tension clamp at Max. operating temp. AS4181-1999 up to and including
DN350mm clamps
(Specifications are subject to change without notice).
www.australianminingservices.com.au Page 3
FLANGED CLAMPS ONE PART FL Drilled "D"
3" 4" 6"
PART NO RANGE Size, Length, Bolts 80mm 100mm 150mm
CF1-0375-16 x FL 95 - 104 M12 X 400 X 4 √
CF1-0440-16 x FL 104 - 111 M12 X 400 X 4 √
CF1-0450-16 x FL 113 - 120 M16 X 400 X 4 √ √
CF1-120/130-16 x FL 120 - 130 M16 X 400 X 4 √ √
CF1-0500-16 x FL 126 - 133 M16 X 400 X 4 √ √
CF1-0520-16 x FL 130 - 137 M16 X 400 X 4 √ √
CF1-0590-16 x FL 145 - 152 M16 X 400 X 4 √ √
CF1-0600-16 x FL 151 - 158 M16 X 400 X 4 √ √
CF1-160/170-16 x FL 160 - 170 M16 X 400 X 4 √ √ √
CF1-0663-16 x FL 167 - 174 M16 X 400 X 4 √ √ √
CF1-175/185-16 x FL 175 - 185 M16 X 400 X 4 √ √ √
CF1-0745-16 x FL 189 - 196 M16 X 400 X 4 √ √ √
CF1-195/205-16 x FL 195- 205 M16 X 400 X 4 √ √ √
CF1-0800-16 x FL 202- 212 M16 X 400 X 4 √ √ √
Flange off take neck length from top of skin to bolting face of flange, 3" (DN80) & 4"
(DN100) & 6" (DN150) = 100mm. Other Flanges available e.g. Tadle E
Example for Part No. DN100 DICL (OD 122) with 100mm Table D flange = CF1-120/130-16 x 100TD
FLANGED CLAMPS TWO & FL Drilled "D"
THREE PART 3" 4" 6"
PART NO RANGE Size, Length, Bolts 80mm 100mm 150mm
CF2-215/230-16 x FL 215 - 230 M16 X 400 X 8 √ √ √
CF2-230/250-16 x FL 230 - 250 M16 X 400 X 8 √ √ √
CF2-250/270-16 x FL 250 - 270 M16 X 400 X 10 √ √ √
CF2-270/290-16 x FL 270 - 290 M16 X 400 X 10 √ √ √
CF2-290/310-16 x FL 290 - 310 M16 X 400 X 10 √ √ √
CF2-310/330-16 x FL 310 - 330 M16 X 400 X 10 √ √ √
CF2-330/350-16 x FL 330 - 350 M16 X 400 X 10 √ √ √
CF2-350/370-16 x FL 350 - 370 M16 X 400 X 10 √ √ √
CF2-370/390-16 x FL 370 - 390 M16 X 400 X 10 √ √ √
CF2-390/410-16 x FL 390 - 410 M16 X 400 X 10 √ √ √
CF2-410/430-16 x FL 410 - 430 M16 X 400 X 10 √ √ √
CF2-420/440-16 x FL 420 - 440 M16 X 400 X 10 √ √ √
CF2-440/460-16 x FL 440 - 460 M16 X 400 X 10 √ √ √
CF2-450/470-16 x FL 450 - 470 M16 X 400 X 10 √ √ √
CF2-470/490-16 x FL 470 - 490 M16 X 400 X 10 √ √ √
CF2-480/500-16 x FL 480 - 500 M16 X 400 X 10 √ √ √
CF2-490/510-16 x FL 490 - 510 M16 X 400 X 10 √ √ √
CF2-510/530-16 x FL 510 - 530 M16 X 400 X 10 √ √ √
CF2-530/550-16 x FL 510 - 530 M16 X 400 X 10 √ √ √
CF2-550/570-16 x FL 550 - 570 M16 X 400 X 10 √ √ √
CF3-490/520-16 x FL 490 - 520 M16 X 400 X 15 √ √ √
CF3-520/550-16 x FL 520 - 550 M16 X 400 X 15 √ √ √
CF3-550/580-16 x FL 520 - 550 M16 X 400 X 15 √ √ √
CF3-580/610-16 x FL 580 - 610 M16 X 400 X 15 √ √ √
CF3-620/650-16 x FL 620 - 650 M16 X 400 X 15 √ √ √
CF3-650/680-16 x FL 650 - 680 M16 X 400 X 15 √ √ √
CF3-690/715-16 x FL 690 - 720 M16 X 400 X 15 √ √ √
CF3-720/750-16 x FL 720 - 750 M16 X 400 X 15 √ √ √
CF3-750/780-16 x FL 750 - 780 M16 X 400 X 15 √ √ √
CF3-780/810-16 X FL 780 - 810 M16 X 400 X 15 √ √ √
www.australianminingservices.com.au Page 4
Flange off take neck length from top of skin to bolting face of flange, 3" (DN80) & 4"
(DN100) & 6" (DN150) = 100mm.
8" (DN200) & 10" (DN250) = 130mm (Min. Clamp Width 600mm),
Other Flanges available e.g. Tadle E
Example for Part No. DN300 DICL (OD345) with 150mm Table D flange = CF2-330/350-16 x 150TD
R4
www.australianminingservices.com.au Page 5
AMPSflo Galvanized Compression Couplings
AMPSflo Clamps Galvanized Compression Couplings are made to suit
Australian standard galvanised, steel and uPVC pressure pipe sizes, and are an
effective way to join these pressure pipes together.
Body and end nuts made from malleable galvanized iron. Pressure rating
1600kPa. Available to suit DN15mm, DN20mm, DN25mm, DN32mm, DN40mm
and DN50mm, pipe sizes.
GALVANIZED COMPRESSION COUPLINGS
AMPSflo/Cascade Clamps Galvanized Compression Couplings are made
to suit Australian standard galvanised, steel, and uPVC pressure pipe
sizes, and are an effective way to join these pressure pipes together.
MATERIAL
AMPSflo/Cascade Clamps, galvanized compression couplings, are
designed and manufactured under Quality Management System,
certificate to ISO9001:1994.
www.australianminingservices.com.au Page 1
Couplings and End Nuts
Malleable Galvanized Iron
Gasket
Natural Rubber
Pressure Rating
1600 KPa.
Galvanized Compression Couplings
Code DN Size To Suit OD Pipe
RGC15S 15mm ½ inch 21.3mm
RGC20S 20mm ¾ inch 26.7mm
RGC25S 25mm 1 inch 33.4mm
RGC32S 32mm 1 ¼ inch 42.2mm
RGC40S 40mm 1 ½ inch 48.3mm
RGC50S 50mm 2 inch 60.3mm
This Product Does Not Restrain Axial Pipe Movement E & O.E
www.australianminingservices.com.au Page 2
AMPSflo Restraint Couplings
AMPSflo Restraint Couplings are a quick and easy way of restraining pipes and
fittings used in the water systems, eliminating the need of blocking. They are
also designed to fit over the Variable Gibault style of fittings that are now
commonly used. This will stop the Gibault walking down the pipe.
Pressure rating 1600kPa. Sizes from DN 80mm to DN300mm
www.australianminingservices.com.au Page 1
AMPSflo BELL HOUSE/SOCKET
REPAIR COUPLINGS
Repair Couplings are a quick and easy way of repair leaking pipe sockets
and double collar joins. They are available for Ductile Iron, Cast Iron,
Asbestos Cement, uPVC, and other types of pipes, which have been joined
together via a single or double socketed joint. They eliminate the need to
“cut out” a leaking socket join, or double socket join. The coupling bodies
and rubber seal/s, are interlocking and fit around the pipe, so they can be
installed without disrupting the internal flow.
MATERIAL SPECIFICATION & STANDARDS
AMPSflo/Cascade clamps Bell House/Socket Repair Couplings, are
designed and manufactured under Quality Management System,
certificate to ISO9001:1994.
Gasket and Epoxy Powder Coating, conforms to BS6920 WRAS, for potable
water.
www.australianminingservices.com.au Page 2
Flange Rings Bolts, Nuts and Washers
Ductile iron 420/12 to BS 2789. Galvanised. 4.6MPa.
Gasket Coating
EPDM Rubber to BS6920 for potable water.
Epoxy Powder Coated, BS6920 Working Pressure: 1.6MPa.
Working Temperature: 0 to 80 Degrees
BELL HOUSE/SOCKET REPAIR COUPLINGS
Pipe Pipe Materials OD Range Bolt Size, Length, No.
Nom Code (mm) (mm)
80mm BH-94GS Ductile Iron, Cast Iron, AC, uPVC 94 -100 M16 x 235 x 4
100mm BH-121GS Ductile Iron, Cast Iron, AC, uPVC 121 - 127 M16 x 235 x 4
150mm BH-174GS Ductile Iron, Cast Iron, AC, uPVC 174 - 181 M16 × 235 x 4
200mm BH-229GS Ductile Iron, Cast Iron, AC, uPVC 229 - 237 M16 × 235 x 4
225mm BH-255GS Ductile Iron, Cast Iron, AC, uPVC 255 - 263 M16 x 235 x 6
250mm BH-281GS Ductile Iron, Cast Iron, AC, uPVC 281 - 291 M16 x 235 x 6
300mmB BH-330GS Cast Iron (B), AC (AB) 330 - 340 M16 x 300 x 6
300mmC BH-343GS Ductile Iron, Cast Iron, AC, uPVC 343 - 353 M16 x 300 x 6
BH = Bell House Couplings. G = Galvanised Fasteners, S = Single repair, D = Double Repair, (longer bolts/tie rods required)
E & O.E
www.australianminingservices.com.au Page 3
AMPSflo Sewer OB Clamps
AMPSflo Sewer OB Junction clamps are suited for new or damaged property
connections on non-pressure sewer pipelines designed for a permanent sewer
branch. The off-take branch has a uPVC access coupling, and they are made to
adapt to pipe ovalities and irregularities. Fully lined rubber gasket, damaged
pipes can be easily rehabilitated. Sizes range from DN150mm upwards, with off
takes sizes DN100 and DN150mm. Operating pressure from -80kPA to 100kPA.
Maximum temperature 60 degrees C. Stainless Steel 316.
AMPSflo Sewer OB Junction Clamps
www.australianminingservices.com.au Page 1
AMPSflo Sewer OB Junction clamps are made from 316 Stainless Steel,
they are ideally suited for new or damaged property connections on non‐
pressure sewer pipelines designed for a permanent sewer branch.
They are made to provide the same quick‐and‐easy AMPSflo fitting
qualities. All of the AMPSflo Sewer Junction Clamps are made using AS
4181 requirements* and in accordance with ISO 9001 quality standards.
They provide a simple and permanent way of connecting branch off‐takes
to new, broken, and renewed/re‐lined sewer pipes. The standard sewer
clamps come with the off‐ take branch at 45 degrees, and has an uPVC
access coupling secured to it for solvent welded connections to uPVC
pipes. The sewer clamps are made to adapt to pipe ovality and
irregularities. With a fully lined rubber gasket, damaged pipes can be
easily rehabilitated.
Sizes range from DN 150 to DN 600mm, with off takes sizes DN 100 and
DN 150mm. (Depending on host pipe) Operating pressure from ‐80kPA to
100kPA. Max. temp. 60 degrees C.
COMMON AMPSFLO OB SEWER CLAMPS
OD
PART NO RANGE DESCRIPTION
CBJ-160/170-100 160 - 170 OB SS316 CLAMP 160 to 170 x 100 x 45 uPVC
CBJ-175/185-100 175 - 185 OB SS316 CLAMP 175 to 185 x 100 x 45 uPVC
CBJ-190/210-100 190 - 210 OB SS316 CLAMP 190 to 210 x 100 x 45 uPVC
CBJ-190/210-150 190 - 210 OB SS316 CLAMP 190 to 210 x 150 x 45 uPVC
CBJ-225/245-100 225 - 245 OB SS316 CLAMP 225 to 245 x 100 x 45 uPVC
CBJ-225/245-150 225 - 245 OB SS316 CLAMP 225 to 245 x 150 x 45 uPVC
CBJ-250/270-100 250 - 270 OB SS316 CLAMP 250 to 270 x 100 x 45 uPVC
CBJ-250/270-150 250 - 270 OB SS316 CLAMP 250 to 270 x 150 x 45 uPVC
CBJ-270/290-100 270 - 290 OB SS316 CLAMP 270 to 290 x 100 x 45 uPVC
CBJ-270/290-150 270 - 290 OB SS316 CLAMP 270 to 290 x 150 x 45 uPVC
CBJ-310/330-100 310 - 330 OB SS316 CLAMP 310 to 330 x 100 x 45 uPVC
CBJ-310/330-150 310 - 330 OB SS316 CLAMP 310 to 330 x 150 x 45 uPVC
Larger host pipe sizes available.
E. & O.E.
*AS4181 pressure testing requirements reduced
www.australianminingservices.com.au Page 2
Off line or On line Pipe Repair
Fiberglass Repair Tape
provides an industrial strength, permanent, quick, and cost- effective
solution to repair and reinforce any kind of pipe leaks in minutes,
without the need for expensive and time- consuming pipeline
shutdown
Resin & Activator
two-component epoxy anti-corrosive coating used for corrosion
resistance and protection for metals, plastics and
many substrate materials. It mainly acts as a corrosion barrier,
remediates & reinforce pipelines, vessels, storage tanks, etc.
Clamps
Standard Leak Repair Clamps
permanent pipe repairs for corrosion, cracks and impact damage
removing the requirements for costly shutdowns, usually associated
with pipe repair. Features wide tolerances and are suitable for use
with a wide variety of pipe materials.
Premium Leak Repair
Clamps are employed specifically for permanent pipe repair for
corrosion, cracks and impact damage under high pressure and elevated
temperature environment. The product comes in broad ranges (sizes)
that are suitable for use with a wide variety of pipe materials
www.australianminingservices.com.au Page 3
Clamps for the Rapid Coupling or the INSTANT repair to
leakages on HDPE or Carbon steel pipes
www.australianminingservices.com.au Page 4
ADVANTAGES
• Leak repair help to stop the leak without
replacing the system
• Time saving- repair can be addressed
within an hour
• Flexible- online and offline leak repairs
available
• Online or live leak repair provides cost effective
solution as compared to system shutdown
• Extend the operating life of the leak section
www.australianminingservices.com.au Page 5
www.australianminingservices.com.au Page 6
www.australianminingservices.com.au Page 7
Single –Clip Pipe repair clams
Folding Type Pipe Repair Clamp RCH
Folding Short Type RCH-S holding Short Type RCH-L
Product Features
RTH Folding series is widely used On quick repairing of pipe leafs which can seal under pressure and no need of changing pipes.8eJp a lot on
repairing pin h0les and breaks caused by aging or use ng.have advantages of safe,convenIent and eflclency.
Flexible co nnection, wea r and corrosion resistance, no need welding, no fire, s pace saving, na limit for
p pe materiaIs,vnder pressure sealing and easy Installation.
(PL H ?1
Application Pipeline
Crud0:’OiJ Pipeline, Gas and ruel Pipelines, supply and Drainage Water Pipeline, Aviation and Autom0tive ,•,
Speclal Pipeline, LubrlcetJnq oii Pipeline, Hud Sleg PIpeIIne,Suction Pipeline, r1ushlng Powder Pipeline,
cable Protection Pipeline, Sea and Fresh Water Pipeline, Turbine Pipeline, Air Conditioning Pipeline, Fire
Line, Verrtilati0n Pipeline, Compressed Air Pipeline etc. '
Applicatioñ Area
Surface and M derground project, Shipbuilding and Offshore oil Platform,water and Gas and ruel Supply. Electrical and Industrial
ProduccIAn,DraJnage and Nalntenance Pipeline praise\s.
www.australianminingservices.com.au Page 8
www.australianminingservices.com.au Page 11
www.australianminingservices.com.au Page 12
www.australianminingservices.com.au Page 13
Single SS Plate Pipeline Repair Clamps
www.australianminingservices.com.au Page 14
Jaw Type Ductile iron and Stainless steel Repair Clamps
ITEM CODE - AMPS STR DRP
BOLTINGS NUMBER ACCORDING TO LENOTH
LENGTH(MM) 150 191/200 250 300 382 400 500
BOLTINGNUM. 2 3 4 4 6 6 8
MATERIALS COMPOSITION
ITEMS NAME MATERIALS
1 JAW DUCTILE IRON (GGG40)
2 BOLTS CARBON STEEL GALV.
3 NUTS CARBON STEEL GALV.
4 BAND SS304
5 GASKET EPDM/SBR
6 COATING FUSION BONDED EPOXY RAL5017
SIZE OQ RANGE s BOLTING WORAIMG
Ressu&
60-67 150,191.200 250. 300 5/8- OR M16 PN10/16
88-98 150,191.200.250.300 5/8" OR M16 PNJ0/J6
95-105 150.191.200.250.300 5/8" OR M16 PN10/16
108-11g 150. 191.200.250 300.400 5/8” OR M16 PN 0/16
115-128 150.19 .200.250,300.400 5/8“ OR M16 PN10/16
158-172 150.191.200.250.300,400 5/8" OR M16 PN10/16
6"
168-182 150.191.200.250.300,400 5/8" OR M16 PN10/J6
217-229 191.200.300.400 5/8“ OR M16 PN10/16
225-240 91.200.300.400 5/8” OR M16 PN10*16
10- 243-260 1g1.200.300.400 5/8- OR M16 PN10/16
270-288 191.200.300.400 5/8” OR M16 PN10/16
12”
3 3-336 300.400.500 5/8- OR M16 PN10/16
340-360 300.400.500 5/8“ OR M16 PN10/16
[Type text] Page 18
FULL BAND STAINLESS STEEL REPAIR CLAMPS
ITEM CODE : APMS STR SRP
BOLTINGS NUMBER MATERIALS COMPOSITION
ACCORDING TO LENGTH
JEWS NAME MATERIALS
1 BOLT SS304
LENGTH(MM } 150 91/200 3UU 400 500
2 LUG PLATE SS304
3 COUNTER PLATE SS30d
4 WASHER 5S30a
5 NUT SS304 A2-70
BOLTING NUM 2 2 3 5
6 GASKET EPOM/SBR
SS304
BAND
8 7 WEDLING PLATE SS304 2B
WORKING
OD RANGE LENGTH BOLTING
PRESSURE
150 191.200 250.300
2’ 60-67 5/8“ OR M16 PNI 0/J6
88-98 150.191.200.250.3D0 5/8" OR M16 PN10/16
3- 150,191.200,250.300 PN10/16
95-105 5/8- OR M16
10B-018 150.191.200.250.300.400 5/8- OR M16 PN10/16
115-128 150,1g1.200.250 300 400 5/8” OR M16 PN10/16
PN10/16
1S8-172 150.191.200.250,300.400 5/8" OR M16
6" PN10/16
168-182 150.191.200.250,300,400 5/8" OR M16
PN10/J 6
2 7-229 191.200.300,400 5/8 OR M16
8 PN10/ 16
225-240 191.200.300.400 5/8" OR M16
PN10/J6
243-260 191.200.300.400 5/8" OR M16
10- PN10/16
270-288 191.200.300.400 5/8- OR M16 PN10/ 16
300.400 500 300.400.500 5/8" OR M16
12" 313-J36 PN10/ 16
340-360 5/8" OR M16
www.australianminingservices.com.au Page 19
FULL BAND STAINLESS STEEL REPAIR CLAMPS
FOR SIZE 2" AND SMALLER:BAND THICKNESS 0.5MM MIN FOR SIZE 2-1/2" AND BIGGER: BAND
THICKNESS 0 7MM MIN
4 WASHE R ) LUG
PN10/16/150PSI
5 NUTS 2 BOLT!$ [ MATERIALS
I DUCTILE IRON
@ BA^vD 3G ASK ET
2 CARBON STEEL GALVANIZED EPDM
CARBON STEEL GALVANI2ED CARBON STEEL GALVANIZED
6 D L STAINLESS STEEL SS304 BOLTINGS MASS{KGS)
RANGE
3- M10(3*8" I X 1 0 22
1 2“ 6* 21-25 M10(3/8" I X 2 0 44
M10(3/8* I X 4 0 88
M10(3/8") X 1 0.24
26-30 M10(3/8") X 2
3/4" 6" 0.48
12“ M1O(3/8") X 4 0 96
M10(3*8" j X 1 0 27
1- 6- 33-37 M10(3/8") X 2 0 54
12“ M 0(3/8* j x 4 1 08
M10(3/8") X 1
L 3" 0 30
1-1/4" 6“ 42M5 M10(3/8") X 2 0 60
12’ M10(3/8") X 4 1.20
3’ M 0(3/8" I x 0 32
1-1 2” 6- M10(3/8") X 2 0 64
12’ M10(3/8"j X 4 1 28
M10(3/8") X 1 0.33
2’
6- 60-65 M10(3/8") X 2 0 65
12’ M10(3/8*) X 4 1.30
M12{ 1 2"I x 1 0 65
2-1,’2“ 6- 7 1-76 M12f 1 ’2“ } X 2 J 30
/
\ 2" M12f 1 2”) X 4 2 60
ITEM CODE : AMPS STR SS1 M12(1/2") X 1 0.76
3’ 6- 87-93 M12(1/2") X 2 1.45
12’ M12(1/2") X 4 2.90
M12( 1/2” j X 1
3* 0 78
4" 6’ 112-118 M12( 1/2") X 2 1 55
12’ M12( 1 ’2”) X 4 3 10
M12(1/2-j X 1
- 0 85
6" 6“ 167-173 M12( 1/2*) X 2 1 70
12- M12(1/2”) X 4 3.40
3- M12‹ 1/2*) X 1 depending
199-209
10" 8’ 6“ G" 250-262 M12(1/2 X 2 M12( depending
M12( 1 +2") X 2
219-229
@!&
12" 273-286 1/2*) X 4 M12( 1/2*) depending
depending
M12( 1.’2") X 4
12’ depending
M12( 1/2") X 1
12" 3- 315-330 X 1 M12( 1*2“) X 2 depending
depending
6”
12” 322340 depending
ITEM CODE : AMPS STR SS2-G
www.australianminingservices.com.au Page 20
UNIVERSAL COUPLINGS & FLANGE ADAPTORS
UNIVERSAL COUPLINGS & FLANGE ADAPTOR
MATERIALS: BODY:
DUCTILE IRON GJS450-10
GLAND:
DUCTILE IRON GJS450-10
GASKET:
EPDM/SBR
BOLTINGS:
CARNON STEEL GALV GRADE 8 8
ITEM CODE : STR-C WELD ON TYPE AVAILABLE
COATING.FUSION BONDED EPOXYRAL501 7
BOLTS CAP:
NBR
ALTERNATIVELY BOLTINGS:
STAINLESS STEEL
OR CARBON STEEL GEOMET
COATING:
RILSANI NYLON 11 )
APPLICATION:
UNIVERSAL FOR DUCTILE IRON PIPE.CAST IRONPIPE STEEL PIPE ASBESTOS CEMENT PIPE.UPVC ITEM CODE : AMPS -STR-FA
PIPE
SIZE OD RANGE APPROX WEIGHT(KGS)
INCH DN ‹uui BOLTINGS x NUM. COUPLING FLANGE ADAPTOR
40 48-58 MI 2X2
2’ 50 59-73 3,3 4.3
65 72-85 4 5
3’ 88-103 6,2 60
J“ lU0 10g-1}8 M12XJ 6 8 6 5
5’ 125 432-154 M12X4 6 6 7 6
6’ 150 159-182 M12X4 02 9 5
200 218-235 M12X4 10.4 10.7
IO’ 250 271 289 V12X6 1 2 7 14 5
12a 300 315-332 M12X6 18 4 19 1
1 2" 300 322 3-‹n M12X6 18 4 91
14” 350 374-391 M12X8 24.0 26 0
400 386-4 14 M 12Xg 280
16” 4 7-437 M12X8 48 5 29 0
J8" 480 500 M]2X10 320 33 5
20’ 500 526-546 M12X 12 400 500
600 630-650 M12X12 44.0 W0
www.australianminingservices.com.au Page 21
PIPE REPAIRING AND JOINTS
ITEM CODE : AMPSSTR- ITEM CODE : AMPSSTJ-
CPE DIS
RESTRAINED COUPLINGS FOR PE DISMANTLING JOINT - 50 NB TO
/PPR 1600NB
ITEM CODE : AMPS STJ-RS
SEPARATE OFFERING: ASK FOR DETAILS
ITEM CODE: AMPS STJ-G
GIBAULT JOINTS - PVC: HDPe : STEEL
ITEM CODE : AMPS STJ-RD
FLEXIBLE UNION THREADED RUBBER JOINTS
www.australianminingservices.com.au Page 22
ITEM CODE: STR-UU ITEM CODE: STR-TRI
UNIVERSAL DUAL CLAMPS DN80-300 UNIVERSAL TRIPLE CLAMPS DN80-300
ITEM CODE: STR-STEE ITEM CODE: STR-UPT
TAPPING SADDLE UNDER PRESSURE TEE
www.australianminingservices.com.au Page 23
PIPE REPAIRING AND JOINTS
ITEM CODE: STR-@FA
Quick Flange adaptor
S I Z E 50/63 60-65/63 60-65/75 80/90 100/110 125/125 125/140 150/160 200/200 200/225 250/250 300/315 UNIT WT 1 8
2 3 2.2 2.6 3.1 4 1 3.7 5.8 10 6 10.8 12.7 15 1
ITEM CODE: STR-@FA-DI
QUICK FLANGE ADAPTOR FOR DI PIPE
ITEM CODE: STR-RFA
UNIFLANGE
RESTRAINED FLANGE ADAPTOR FOR DI PIPE DN80-300
www.australianminingservices.com.au Page 24
PIPE REPAIRING AND JOINTS
ITEM CODE: STR-S1 ITEM CODE: STR-S2
REPAIR SADDLES FOR PVC SIZE: 63. 75. 90. 110. DCI SADDLES FOR DI PIPE
160
THREAD 3/4- 1" 1-1/4”. 1-1/2". 2"
ITEM CODE: STR-SLY ITEM CODE: STR-SNW
SADDLE WITH INTERGRATED STOP SADDLE WITH STRAP NO WELDING DESIGN
ITEM CODE: STR-SUS
US STYLE SAOOLE WITH STAP U BOLTS
08
www.australianminingservices.com.au Page 25
PIPE REPAIRING AND JOINTS
ITEM CODE: STR-CL
LONG SLEEVE COUPLINGS
ITEM CODE: STR-MJKIT
AWWA C 153 MJ GLAND PACK
ITEM CODE: STR-RSG
AWWA C153 RESTRAINED GLAND PACK
www.australianminingservices.com.au Page 26
www.australianminingservices.com.au Page 27
Australian Mining Product and Services UNIVERSAL
JOINTS AND SADDLES
DN SIZE pipe OD range APPROX WT
15 1/2” 19 7-2 1 8 0 43
20 3/4" 24.6-27.3 045
25 1“ 31 4-34 2 049
32 1-1/4” 40.0-42 9 0.69
40 1-1.'2" 47 g-51 5 0 93
50 2* 59.7-63 6 l A5
ITEM CODE: UNICLAMP-S
DN SIZE pipe OD range APPROX WT
5 1/2" 19 7-2 1 8 045
20 3/4" 24 6-27.3 0.49
25 31 4-34 2 053
32 1-1/4* 40 29 0?6
J0 1-1/2" 47 9-5 1 5 1 00
2’ 59 7-63 6 1 2g
ITEM CODE: UNISADDLE-S
COMPRESSION BALL VALVE FOR PPR/PE
ITEM CODE: PEBV
www.australianminingservices.com.au Page 28
Australian Mining Product and Services PIPES AND
FITTINGS
DUCTILE IRON PIPE
ISO253 1 EN54 ?/ BS4 772 KB K 12 SIZE
AVAILABLE DNg£J-DN?00
DUCTILE IRON PIPE FITTINGS FOR UPVC
DUCTILE IRON PIPE FITTINGS
EN54 › L YOUNG FLANG 6 SOLID FLANGE
www.australianminingservices.com.au Page 29
Australian Mining Product and Services UNIVERSAL
JOINTS AND SADDLES
DIN2440 BS1387
HOT DIP GALVANIZED ZINC WEIGHT
380G/M2 SIZE 1/2"-8°
CARBON STEEL GALVANIZED PIPE
ITEM CODE: MF-RS ITEM CODE: RCD-S
TYPE WITH GRIPPERS AVAILABLE
STAINLESS STEEL COUPLINGS
OUCTILE IRON GROOVED FITTINGS
www.australianminingservices.com.au Page 30
DCI+SS Band Repair clamps price list
code no.: STR-DRP MATERIALS: DCI JAW, SS304 BAND, EPDM GASKET
size O.D.range length unit WT.
45-55 150 2.61
1.5" 48-56 200 3.64
45-55 300 5.21
150 2.66
191 3.59
2" 60-67
200 3.73
250 4.85
300 5.32
150 2.69
191 3.62
2.5" 70-80
200 3.77
250 4.89
300 5.37
150 2.86
191 3.80
88-98 200 3.93
250 4.70
3" 300 5.71
150 2.87
191 3.82
95-105 200 3.96
250 4.96
300 5.75
500 9.91
150 2.93
191 3.95
108-118 200 4.06
250 5.28
4" 300 5.86
150 2.95
191 3.97
115-128 200 4.13
250 5.31
300 5.91
400 8.18
150
3.09
130-145 191 4.12
250 5.50
5" 300 6.18
150 3.12
191 4.16
140-155
200 4.23
250 5.55
300 6.24
150 3.22
191 4.59
200 4.45
6" 158-172 250 5.57
300 6.43
400 9.15
500 10.88
www.australianminingservices.com.au Page 31
600 12.72
150 3.25
191 4.63
200 4.50
6" 168-182 250 5.57
300 6.50
400 9.24
500 11.22
600 13.12
191 4.69
200 4.56
180-193 250 5.86
300
6.80
400
7" 9.31
600 13.22
191 4.72
200 4.60
190-203 250 5.90
300 6.85
400 9.37
600 13.33
191 4.61
200 4.88
217-229 300 7.05
400 9.90
8" 500 12.34
600 14.09
200 4.91
300 7.20
225-240
400 9.96
500 12.41
600 14.28
191 5.12
200
5.31
10" 243-260 300 7.43
400 10.52
500 12.76
600 15.27
191 5.21
200
5.41
11" 265-280 300 7.57
400 11.03
500 13.00
600 15.56
300 7.65
290-310
500 15.36
600 17.62
12" 300 8.10
313-336
400 11.96
300 8.57
340-360 400 12.15
500 17.36
* Double bands, Triple bands available upon request
** Ranges other than above available upon request
www.australianminingservices.com.au Page 32
The words you are searching are inside this book. To get more targeted content, please make full-text search by clicking here.
Discover the best professional documents and content resources in AnyFlip Document Base.
Search