Книга Калибры патронов и оружия в Таблицах ПМК

C.I.P. Testing of safety TAB. II BR/2
Rifled weapons DATE 83-02-03
for rimmed cartridges REV. 94-10-25

Reference gauge
Testing of breech depth R min

GO
and maximal headspace R max

No GO

R min = R

R max = R min + headspace

(P1) P1 P1 P2 x2
L1 R

(P2) P1 P1 P2 (L R)
L1 R

L = L1 x 0,75 ” 25 mm

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

748

C.I.P. Testing of safety TAB. III BR/2
Rifled weapons DATE 83-02-03
for Magnum cartridges REV. 94-10-25

Reference gauge
Testing of breech depth E min

GO
and of maximal headspace E max

NO GO

E min = E

E max = E min + headspace

(P1) P1 P1 P2 x2
L1 E

(P2) P1 P1 P2 (L E)
L1 E

L = L1 x 0,75 ” 50 mm

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

749

C.I.P. Testing of safety TAB. V B/7
Rimfire cartridges DATE 82-03-19
REV. 94-10-25

Reference gauge
Testing of maximal headspace Fe

NO GO

* = at intersection of lines

R1 = R1 max (cartridge)
c = P1 max -0,5
Fe = R min + headspace

D1 P1 P1 H2 x1,5
L3 R max

D2 P1 P1 H2 (L Fe)
L3 R max

L = 0,75 L3 ” 12

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

750

C.I.P. Testing of safety TAB. V B/8
Weapons for rimfire cartridges DATE 82-03-19
REV. 94-10-25

Reference gauge
Testing of minimal breech depth R

GO

* = at intersection of lines

R1 = R1 max (cartridge)
c = P1 max - 0,5
R = R min (chamber)

D1 P1 P1 H2 x1,5
L3 R

D2 P1 P1 H2 (L R)
L3 R

L = 0,75 L3 ” 12

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

751

C.I.P. Testing of safety TAB. VI BR/7
Appliances for industrial use DATE 82-03-19
REV. 90-06-13

Reference gauge
Barrels

Testing of minimal breech depth R
GO

* = at intersection of lines

R1 = R1 max (cartridge)
c = P1 max - 0,5
R = R min + headspace

D1 P1 P1 H2 x1,5
L3 R max

D2 P1 P1 H2 (L Fe)
L3 R max

L = 0,75 L3 ” 12

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

752

C.I.P. Testing of safety TAB. VI B/1
Appliances for industrial use DATE 83-02-03
REV. 90-06-13

Cal. „8 Gauge industriel“
Reference gauge

Testing of minimal diameter P1
GO

Note: The gauge should go into the chamber at least up to the mark A.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

753

C.I.P. Testing of safety TAB. VI B/2
Appliances for industrial use DATE 85-03-26
REV. 90-06-13

Cal. „8 Gauge industriel“
Reference gauge

Testing of minimal diameter H2 and minimal length L3
GO

Note: The gauge should go totally into the chamber.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

754

C.I.P. Testing of safety TAB. VI B/4
Appliances for industrial use DATE 85-03-26
REV. 90-06-13

Cal. „8 Gauge industriel“
Reference gauge

Testing of junction cone Į1 maxi

(F) = F min + 0,8

(H2) = H2 min – 0,1

(G min) (H2) (F)
2 tan g D1

2

(L3) = L3 min + 5,00

Note: 1. The surface of the gliding spike must not overhang the upper surface of the gauge.
2. The gauge may be produced with a smaller or a larger length than the minimal length of
the chamber.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

755

C.I.P. Testing of safety TAB. VI B/5
Appliances for industrial use DATE 85-03-26
REV. 90-06-13

Cal. „8 Gauge industriel“
Reference gauge

Testing of minimal breech depth R

* = at intersection of lines

c = D1 – 1,5

e min R min R1 max P1 min tan gJ
2

D1 = H1 – 0,10

D2 D1 H1 H2 x19,5
L3 L2

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

756

C.I.P. Testing of safety TAB. VI B/7
Appliances for industrial use DATE 85-03-26
REV. 92-10-01

Cal. „8 Gauge industriel“
Reference gauge

Testing of minimal breech depth R
GO

* = at intersection of lines

c = D1 – 1,5

e min R min R1 max P1 min tan gJ
2

D1 = H1 – 0,10

D2 D1 H1 H2 x19,5
L3 L2

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

757

C.I.P. Testing of safety TAB. VI B/8
Appliances for industrial use DATE 85-03-26
REV. 90-06-13

Cal. „8 Gauge industriel“
Reference gauge

Testing of maximal headspace a
NO GO

* = at intersection of lines

c = D1 – 1,5

(e max a) (R min a) R1 max P1 min tan gJ
2

D1 = H1 – 0,10

D2 D1 H1 H2 x19,5
L3 L2

a = maximal headspace

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

758

C.I.P. Testing of safety TAB. VII BR/1
Smoothbore centrefire weapons DATE 83-02-03
REV. 90-06-13

Reference gauge
Testing of diameter D at the chamber

a = (D max – D min) x 120 (min)
l=a

Note: 1. The gauge should go into the chamber as far as the breech face be placed between the
marks A and R. If the gauge enters more as to the mark R, the breech depth should be
verified.

2. Two different gauges MINI and Maxi can be used.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

759

C.I.P. Testing of safety TAB. VII BR/2
Smoothbore centrefire weapons DATE 83-02-03
REV. 90-06-13

Reference gauge
Testing of diameter H and minimal length of chamber L

GO

L’  L’’  L’’’ = L min

Note: 1. The gauge should go as far as the mark that correspond the length of the chamber.
2. For each length of the chamber a corresponding gauge can be used.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

760

C.I.P. Testing of safety TAB. VII BR/3
Smoothbore centrefire weapons DATE 83-02-03
REV. 90-06-13

Reference gauge
Testing of diameter H and maximal length of chamber L

NO GO

L’ max  L’’ max  L’’’ max = L min + 2

Note: 1. The gauge should not totally go into chamber.
2. For each length of the chamber a corresponding gauge can be used.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

761

C.I.P. Testing of safety TAB. VII BR/4
Smoothbore centrefire weapons DATE 83-02-03
REV. 95-11-28

Reference gauge
Testing of junction cone Į1

Note: 1. The surface of the gliding spike must not overhang the upper surface of the gauge.
2. The gauge may be produced with a smaller or a larger length than the minimal length of the
chamber.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

762

C.I.P. Testing of safety TAB. VII AB/7 01
Smoothbore centrefire weapons DATE 80-06-10
REV. 95-11-28

Reference gauge
Testing of minimal and maximal breech depth T

* = at intersection of lines

e min T min g max D min x tan gD
2

c = D min – 1,5

D1 D min D H x(4,5 T)
L T

D2 D min D H x(4,5 T 25)
L T

e max T max g max D min x tan gD
2

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

763

C.I.P. Testing of safety TAB. VII AB/7 02
Smoothbore centrefire weapons DATE 80-06-10
REV. 95-11-28

Reference gauge
Testing of minimal and maximal breech depth T

Weapons for shot cartridges

Barrels side by side

testing position

Barrels superimposed

Testing position
opposite extractor

Testing position
opposite extractor

Note: Mode of application of the gauge for the breech depth.
The testing is to be made at diameters A-A and B-B.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

764

C.I.P. Testing of safety TAB. VII AB/8
Smoothbore centrefire weapons DATE 82-03-24
REV. 95-11-28

Reference gauge
Testing of maximal headspace a

NO GO

* = at intersection of lines

e max a (T min a) g max D min x tan gD
2

c = D min – 1,5

D1 D min L D H a) x[4,5 (T min a)]
(T min

D2 D min L D H a) x[25 4,5 (T min a)]
(T min

a = maximal headspace

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

765

ПРИЛОЖЕНИЕ И1

Перечень контрольных калибров для контроля размеров патронов

766

Reference gauges ANNEXE II
Ammunition
C.I.P. DATE 84-06-14

REV. 00-06-06

List of reference gauges for the dimensions to test
from the point of view of safety

Ammunition

TAB. I - AR/2 - Diameter of the projectile (G1) maxi
TAB. I - AR/3 - Diameter at the case mouth (H2) maxi
TAB. I - AR/4 - Length (L3+G) maxi

TAB. V - AR/4 - Length (L3+G) maxi – rim fire
TAB. V - AR/5 - General form - rim fire
TAB. V - AB/11 - Rim thickness (R) maxi - rim fire

TAB. VI - A/1 - Diameter at the end of rim (P1) maxi (8 Gauge)
TAB. VI - A/5 - Rim thickness (R) maxi (8 Gauge)
TAB. VI - AB/11 - Rim thickness (R) maxi (riveting)

TAB. VII - AB/5 - Rim thickness (t) maxi
TAB. VII - AB/6 - Rim thickness (t) mini
TAB. VII - AR/1 - Diameter at the end of rim (d) maxi and mini

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

767

ПРИЛОЖЕНИЕ И2

Чертежи контрольных калибров для контроля размеров патронов

768

C.I.P. Testing of safety TAB. I AR/2
Ammunition DATE 83-02-04
REV. 90-06-13

Reference gauge
Testing of diameter of the projectile G1

GO

a • G1

Note: The projectile should go totally into the bore of the gauge.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in form of extracts without approval of C.I.P.

769

C.I.P. Testing of safety TAB. I AR/3
Ammunition DATE 83-02-04
REV. 90-06-13

Reference gauge
Testing of diameter H2 of the case

GO

a • H2

Note: The neck should go in part, corresponding the taper, into the bore of the gauge.
Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in form of extracts without approval of C.I.P.

770

C.I.P. Testing of safety TAB. I AR/4
Ammunition DATE 83-02-04
REV. 90-06-13
Reference gauge
Testing the length L3 + G

GO

L3 = Cartridge „maxi“

Note: The base cap of the cartridge must not overhang the upper surface of the gauge.

L3 max = cartridge maximum G min = chamber minimum

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

771

C.I.P. Testing of safety TAB. V AR/4
Rimfire cartridges DATE 86-10-19
REV. 90-06-13
Reference gauge
Testing of length L3 + G

GO

min = chamber minimum
max = cartridge maximum

Kal. L5 max L3 max R

22 Short 14,09 10,69 1,09
22 Long 18,97 15,57 1,09
22 L.R. 20,02 15,57 1,09
22 Ex. Long 22,75 18,30 1,12
22 Ex L.R. 22,23 17,78 1,09

Note: The base cap of the cartridge must not overhang the upper surface of the gauge.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in form of extracts without approval of C.I.P.

772

C.I.P. Testing of safety TAB. V AR/5
Rimfire cartridges DATE 86-10-19
REV. 90-06-13
Reference gauge
Testing the general form

GO

Kal. L3 max R

22 Short 10,69 1,09
22 Long 15,57 1,09
22 L.R. 15,57 1,09
22 Ex. Long 18,30 1,12
22 Ex L.R. 17,78 1,09

Note: The bas cap of the cartridge must not overhang the upper surface of the gauge.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

773

C.I.P. Testing of safety TAB. V AB/11
Rimfire cartridges DATE 79-06-20
REV. 90-06-13
Reference gauge
Testing of maximal rim thickness R

GO

R1 = R1 min (chamber)
R = R max (cartridge)
P1 = P1 max (cartridge)

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

774

C.I.P. Testing of safety TAB. VI A/1
Cartridges for industrial use DATE 85-03-26
REV. 90-06-13

Cal. „8 Gauge industriel“
Reference cartridge

Testing of diameter at the end of rim P1
GO

Note: The rim must not overhang the upper surface of the gauge.

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

775

C.I.P. Testing of safety TAB. VI A/5
Cartridges for industrial use DATE 85-03-26
REV. 90-06-13

Cal. „8 Gauge industriel“
Reference gauge

Testing the maximal rim thickness R
GO

e R max R1min P1max . tan g35q
2

mini = chamber

maxi = cartridge

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

776

C.I.P. Testing of safety TAB. VI AB/11
Cartridges for industrial use DATE 79-06-20
REV. 90-06-13

Reference gauge
Testing of maximal rim thickness R

GO
With rim firing

R1 = R1 min (chamber)
R = R max (cartridge)
P1 = P1 max (cartridge)

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

777

C.I.P. Testing of safety TAB. VII AB/5
Shot cartridges DATE 78-05-02
REV. 90-06-13

Reference gauge
Shot cartridges for smoothbore centrefire weapons

Testing of maximal rim thickness t
GO

e t max i G mini d max i . tan g35q
2

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

778

C.I.P. Testing of safety TAB. VII AB/6
Shot cartridges DATE 78-05-02
REV. 90-06-13

Reference gauge
Shot cartridges for smoothbore centrefire weapons

Testing of minimal rim thickness t
NO GO

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

779

C.I.P. Testing of safety TAB. VII AR/1
Shot cartridges DATE 83-02-04
REV. 90-06-13

Reference gauge
Shot cartridges for smoothbore centrefire weapons
Testing of minimal and maximal diameter d under the rim

MINI
NO GO

MAXI
GO

Note: The rim must
(Condition minimal) overhang the rim recess of the gauge
(Condition maximal) sink into the rim recess of the gauge

Tolerances = ISO 286-2: 1986 (F)

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

780

ПРИЛОЖЕНИЕ К1

Перечень баллистических стволов

781

Proof barrels ANNEXE III
Dimensions and tolerances
C.I.P. DATE 02-05-15

REV. 03-04-11

List of proof barrels

TAB. I - CR 1 - Rimless cartridges
TAB. II - CR 1 - Rimmed cartridges
TAB. III - CR 1 - Magnum cartridges
TAB. IV - CR 1 - Pistol and revolver cartridges
TAB. V - CR 2 - Rimfire cartridges
TAB. VI - CR 3 - Cartridges for industrial use
TAB. VII - CR 4 - Shot cartridges
TAB. VIII - CR 5 - Cartridges for alarm weapons
TAB. IX - CR 6 - Dust shot cartridges

2007 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

782

ПРИЛОЖЕНИЕ К2

Размеры и предельные отклонения размеров баллистических стволов

783

Proof barrels TAB. I - IV CR 1
Rifled weapons
C.I.P. DATE 02-05-15

REV. 03-04-11

Dimensions and tolerances of proof barrels for cartridges
intended for rifled centrefire weapons

1. Interior dimensions:

For the dimensions see the minimum values in the TDCC.

The following tolerances are authorised:

___________________________________________________________________

F Z L3 P1 P2 H2 G1 i t 12' i < 12'

+0,02 +0,03 +0,1 +0,03 +0,02 +0,02 +0,03 mm - 5/60 i - 1’

___________________________________________________________________

The headspace must not exceed 0,10 mm. Lc = 600 ± 10 mm
Lc = 600 ± 10 mm
2. Length of reference standard proof barrels: Lc = 650 ± 10 mm
Lc = 150 ± 10 mm.
For rimless cartridges:
for rimmed cartridges:
for magnum cartridges:
For pistol and revolver cartridges:

3. Location of the pressure take (M):

For the location of the pressure take (M) see the indications in the TDCC;
Tolerance: -2,00 mm.

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

784

C.I.P. Proof barrels TAB. V CR 2
Rimfire cartridges DATE 02-05-15
REV. 03-04-11

Dimensions and tolerances of proof barrels for
rimfire cartridges (crusher method)

1. Proof barrels for pressure measurement:
1.1. Interior dimensions:

For the dimensions see the minimum values in the TDCC.

The following tolerances are authorised:

For smoothbore shotguns:
___________________________________________________________

F=Z L3 P1 P2 H2 G1 i

+0,03 +0,10 +0,05 +0,05 +0,05 +0,03 -5/60.i (max -1°)
___________________________________________________________

For rifled weapons :

___________________________________________________________

F Z L3 P1 H2 R R1 i

+0,02 +0,02 +0,10 +0,03 +0,02 +0,03 +0,05 r 0°20’
___________________________________________________________

The headspace must not exceed 0,10 mm.

1.2. Length of reference standard proof barrels:

For rimfire cartridges: Lc = 600 ± 10 mm.

1.3. Location of the pressure take (M):

For the location of the pressure take (M) see the indications in the TDCC;
Tolerance: ± 0,20 mm.

2. Proof barrels for measuring kinetic energy (see also decision XV-3):

2.1. For the dimensions see the minimum values in the TDCC.

The following tolerances are authorised:
__________________________

F Zb

r 0.02 r 0.03 r 0.01
__________________________

2.2. Length of reference standard proof barrels: Lc = 200 ± 2 mm.
For rimfire cartridges:

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

785

C.I.P. Proof barrels TAB. VI CR 3
Cartridges for industrial use DATE 02-05-15
REV. 03-04-11

Dimensions and tolerances of proof barrels for cartridges
intended for piston/plunger-operating riveting tools

1. Standard proof chamber (see also decision XVII-7):

For the dimensions see the minimum values in the TDCC.

The following tolerances are authorised:
__________________________________________

L3 P1 H2 R R1

+0,10 +0,03 +0,03 +0,05 +0,05
__________________________________________

2. Piston/plunger operated proof barrel (see also decision XVII-7):

Calibre: 16 mm; tolerance: F7,
Length: 200 ± 1 mm (from the end of the chamber),
Position of the intake of gas: 1,5 mm (from the end of the chamber),
Drilled hole: 3 mm Ø,
Depth of drilling: 3 mm.

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

786

C.I.P. Proof barrels TAB. VII CR 4
Shot cartridges DATE 02-05-15
REV. 03-04-11

Dimensions and tolerances of proof barrels for
shot cartridges

1. Interior dimensions:

For the dimensions see the minimum values in the TDCC.
The following tolerances are authorised:
_____________________________________________________

B G D H T L D1
+0,10 +0,05 +0,05 +0,05 +0,05 +2,00 -30’
_____________________________________________________

The headspace must not exceed 0,10 mm.

2. Length of reference standard proof barrels: Lc = 700 ± 10 mm.
Cylindrical barrel without choke

3. Location of the pressure take (M):

Distance from the central axes of the measurement bores (L) to the breech face:

for calibres 24 and larger: 25 mm d LI d 30 mm,
for calibres smaller than 24-gauge : LI = 17 mm + 1 mm,
for calibres 32-50,7, 410-50,7, 8 mm et 9 mm : LI = 12,5 mm - 0,5 mm,

for all calibres : LII = 162 mm ± 0,5 mm.

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

787

C.I.P. Proof barrels TAB. VIII CR 5
Cartridges for alarm weapons DATE 02-05-15
REV. 03-04-11

Dimensions and tolerances of proof barrels for
cartridges for alarm weapons

1. Proof barrels for pressure measurement:
1.1. Interior dimensions:

For the dimensions see the minimum values in the TDCC.
The following tolerances are authorised (ISO 286-2/1988):
___________________________________________________________________

F=Z L3 P1 H2 R R1 G1 i s w
H8 H11 H8 H8 H9 H10 H11 r 20’ H11 H11
___________________________________________________________________

1.2.1. Length of proof barrels for revolver cartridges:

Length of barrel to bore diameter F = Z: LT = 50 mm (h13),
for calibre 320 court Blanc : LT = 50 mm (h13),
for calibre 380 Blanc/9 mm R Blanc : LT = 63 mm (h13).
for calibre 45 K Blanc :

1.2.2. Length of proof barrels for pistol cartridges:

Total length of barrel: Lc = 60 mm (h13),
for calibre 22 Long Blanc : Lc = 60 mm (h13),
for calibre 315 Blanc : Lc = 60 mm (h13),
for calibre 8 mm Blanc : Lc = 62 mm (h13),
for calibre 35 Blanc : Lc = 62 mm (h13),
for calibre 35 R Blanc : Lc = 62 mm (h13).
for calibre 9 mm PA Blanc :

1.3. Location of the pressure take (M):

For the location of the pressure take (M) see the indications in the TDCC; tolerance: js14.

2. Proof barrels for measuring kinetic energy:

2.1. For the dimensions see the minimum values in the TDCC.
The following tolerances are authorised (ISO 286-2/1988):
________________________________________________________
F=Z L3 P1 H2 R R1 G1 i
F8 H11 H8 H8 H9 H10 H11 r 20’
________________________________________________________

2.2. Length of proof barrels: Lc = 200 (js16).
Length of barrel to bore diameter F = Z:

2003 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

788

C.I.P. Proof barrels TAB. IX CR 6
Dust shot cartridges DATE 02-05-15
REV. 03-04-11

Dimensions and tolerances of proof barrels for
dust shot cartridges

1. Interior dimensions:

For the dimensions see the minimum values in the TDCC.
The following tolerances are authorised (ISO 286-2/1988):
________________________________________________________

F=Z L3 P1 H2 R R1 G1 i
F8 H11 H8 H8 H9 H10 H11 r 20’
________________________________________________________

2. Length of proof barrels: Lc = 62 mm (h13).

3. Location of the pressure take (M):

For the location of the pressure take (M) see the indications in the TDCC;
Tolerance: js14.

2007 Reproduction forbidden as well as in the form of extracts without approval of C.I.P.

789

Производственно-техническое издание

Гринберг Михаил Владимирович

КАЛИБРЫ ПАТРОНОВ И ОРУЖИЯ В ТАБЛИЦАХ ПМК

Ответственный за выпуск С. В. Матвеев
Художественный редактор Ю. Н. Лобанов
Технический редактор и оператор компьютерной верстки Л. А. Павлова

Подписано в печать 01.06.2015. Формат 60х84 1/8. Бумага офс.
Гарнитура Arial. Тираж 100 экз. Заказ № К-242
Государственное унитарное предприятие

Удмуртской Республики «Книжное издательство «Удмуртия»

426011 г. Ижевск, ул. Пастухова, 13.
Тел: (3412)78-79-07 Факс: (3412)78-15-07

E-mail: [email protected]
http://udgiz.udm.net

Отпечатано в ООО «Типография «Новое Время».
428034 г. Чебоксары, ул. Мичмана Павлова, 50/1.