CAPTUS 700t Manual

CAPINTEC, INC. CAPTUS® 700t

e. Lift the other end of the battery up and slide it out. The battery holder will
appear as shown in Figure 16-11.

Figure 16-11

3. Battery Installation
a. Locate the new battery and verify the proper orientation as shown in Figure
16-12 – the positive (+) side of the battery must face up.

October 15 Figure 16-12 16-13

CLEANING AND MAINTENANCE

CAPINTEC, INC. CAPTUS® 700t

b. Slide the battery into the battery holder under the three prongs as shown in
Figure 16-13.

Figure 16-13

c. Press down on the other side of the battery as shown in Figure 16-14 until a
click is heard.

16-14 Figure 16-14 October 15

CLEANING AND MAINTENANCE

CAPINTEC, INC. CAPTUS® 700t

d. Verify that the battery is secure in the connector and not loose.

e. Verify that none of the Flat Flex cables are loosened from their connectors.

f. Gently lift up the Back Case approximately ½” above the Front Case and
carefully move the Back Case to the right and line up the Back Case with the
Front Case.

g. Replace the 4 hex-head screws.

4. Re-attach the Stand Base
Note: Reference Figure 16-15 Readout/Stand Base Assembly.

a. On the previously removed 2 knobs, verify that a washer (C) is over the shaft
of each knob (D).

b. Insert one of the knobs through one side of the Stand Base (B) and place
another washer (E) over the shaft of the knob (on the inside of the Stand
Base).

c. With the front of the Readout (A) facing the same direction as the front of the
Stand Base (B), place the Readout onto the Stand Base.

d. Insert the shaft of the knob (D) into the mounting hole (F) located on the side
of the Readout Unit. Loosely tighten the knob.

e. Insert the other knob (D) with washer (C) through the other side of the Stand
Base and place the other washer (G) over the shaft of the knob (on the inside
of the Stand Base).

f. Insert the shaft of the knob into the mounting hole located on the other side of
the Readout Unit. Note: The sides of the Stand Base may need to be spread
apart a small amount to get the second knob to insert into the mounting hole.

g. Verify on each side that there is a washer between the knob and the Stand
Base (on the outside of the Stand Base), and the Stand Base and the
Readout (on the inside of the Stand Base).

h. The knobs can now be fully tightened.

October 15 CLEANING AND MAINTENANCE 16-15

CAPINTEC, INC. CAPTUS® 700t

Front of A
Readout

D
FC

G

Front of E
Stand Base C

B
D

Figure 16-15 Readout/Stand Base Assembly

5. System Power-Up
a. Reconnect the power cord and ALL other cables.
b. Turn on the power to the Readout Unit and verify that the “Low Battery”
message does not appear on the display.

6. Set the date and time as described in CHAPTER 5: SYSTEM INITIALIZATION.

16-16 CLEANING AND MAINTENANCE October 15

CAPINTEC, INC. CAPTUS® 700t

TROUBLESHOOTING
Some problems may be very easy to diagnose and correct in the field with little or no
equipment. If a problem should occur, check here before calling for service. A considerable
amount of time and money may be saved.

Nothing appears on the display.
• Make sure CAPTUS® 700t is plugged into a live outlet and is turned on.
• Check fuse and replace if necessary. Reference the FUSE SERVICING section
on page 16-8.

Buzzer buzzes continuously.

• A brief power line disruption may have caused the program to “lose its place”. Try
turning the power off and then on again. If the buzzing continues, turn the power
off and consult the factory. DO NOT leave the unit buzzing longer than necessary.

High Background indication.

• The Well Liner may have become contaminated. Reference CHAPTER 8:
ACCEPTANCE & QUALITY ASSURANCE TESTS; SECTION: QUALITY
ASSURANCE TESTS, Contamination Test.

• Background may actually be high. Check by placing a lead sheet over the top of
the Well Counter and re-measure the background.

Indication of significant activity.

• Background level may have changed. Re-measure the background. Reference
CHAPTER 9: TESTS; SECTION: BACKGROUND.

The time is reset to 00:00.

• The internal Lithium Coin Battery may be depleted. Reference the BATTERY
REPLACEMENT procedure on page 16-10.

Printer prints junk or prints with incorrect spacing.

• Make sure that the Printer Menu Setup is correct. Reference CHAPTER 5:
SYSTEM INITIALIZATION, SECTION: PRINTING.

Printer will not respond.

• Make sure printer is plugged into a live outlet, turned on, and “selected”.
• Make sure that either paper or a ticket is in the paper path.
• Run the Diagnostic Test and make sure that the system expects to have a printer.

If not, Make sure that the Printer Menu Setup is correct. Reference CHAPTER 5:
SYSTEM INITIALIZATION, SECTION: PRINTING.

October 15 CLEANING AND MAINTENANCE 16-17

CAPINTEC, INC. CAPTUS® 700t

REPLACEMENT PARTS
The following replacement parts are available from Capintec. Call Capintec’s only Authorized
Service Center at 1-800-227-6832 for answers to your questions or to place an order.

• Ream of Paper – 500 sheets ....................................................... 9282-0011
• Inkjet Printer ................................................................................ 5430-0146
• Inkjet Cartridges .............................................................................. CALL
• USB Printer Cable ....................................................................... 8400-0435
• Well Liners: 5 per package ......................................................... 5120-0176
• Detector Cable, coaxial 10 feet long ............................................ 8400-2236
• Flat Field Detector: 2M2/2 type ................................................... 1200-0028
• Drilled Well Detector: 2MW2/2 type ............................................ 1200-0029
• Detector Base Assembly: PM-700/3000 ..................................... 5420-2126
• Well Detector: 1” Shielding ......................................................... 5420-2033
• Well Detector: 2” Shielding ......................................................... 5430-0069
• Rod Source: Cs137 (0.5 µCi)......................................................0975-137R
• Rod Source: Eu152 (0.5 µCi)......................................................0970-152R
• Rod Source Holder ...................................................................... 7315-1850
• Power Cable: Hospital Grade, 15 feet long ................................. 8125-0024
• Fuse: T 2 Amp. 250 Volts. (Readout Unit) 2 Req. ...................... 2110-0083
• Fuse: T 3.15AH, 250 Volts. (Power Line – 115Volts). 2 Req....... 2110-0077
• Fuse: T 2.5AH, 250 Volts. (Power Line – 230Volts). 2 Req......... 2110-0079
• 3V Lithium Coin Battery (CR2032)............................................... 0500-0039
• Additional copies of Owner’s Manual ........................................... 9250-0142

Note: Circuit diagrams, component parts lists, descriptions and calibration instructions are
available to appropriately qualified personnel.

16-18 CLEANING AND MAINTENANCE October 15

CAPINTEC, INC. CAPTUS® 700t

SHIPPING

If for any reason the CAPTUS® 700t must be returned to Capintec, the shipping carton must
contain the following or equivalent labeling as shown in Figure 16-16. Label stipulating the
maximum environmental conditions for safe storage and shipment.

RANGEZ L'APPAREIL DANS UN ENDROIT DONT LA TEMPÉRATURE
VARIE ENTRE +4 °C (+39 °F) ET +43 °C (+110 °F)

RANGEZ L'APPAREIL DANS UN ENDROIT DONT L'HUMIDITÉ EST
INFÉRIEURE À 90 % SANS CONDENSATION ET DONT
LA PRESSION BAROMÉTRIQUE SE SITUE ENTRE
15 ET 33 PO DE MERCURE (ENTRE 51 ET 112 kPa)
ÉVITEZ TOUT CHOC THERMIQUE ET MÉCANIQUE

LAISSEZ RÉCHAUFFER À TEMPÉRATURE AMBIANTE PENDANT UNE PÉRIODE DE
24 HEURES AVANT DE DÉSEMBALLER ET DE METTRE L'APPAREIL EN MARCHE

Figure 16-16

October 15 CLEANING AND MAINTENANCE 16-19

CAPINTEC, INC. CAPTUS® 700t

This page intentionally left blank.

CAPINTEC, INC. CAPTUS® 700t

APPENDIX

NUCLIDE LIST

The following table is a listing of the default nuclides that are built into the CAPTUS® 700t.
The table shows the primary photopeak keV (Photopeak 1), up to two other photopeaks keV
(Photopeak 2 and Photopeak 3) and the default efficiency nuclides.

Note: --- indicates that the value is not available

The following abbreviations pertain to the half-life:
• H – hours
• M – minutes
• D – days
• Y – years

Nuclide Half-Life Photopeak Photopeak Photopeak Well Probe
1 (keV) 2 (keV) 3 (keV) Efficiency Efficiency
Ag110m Silver 249.80 D
Am241 Americium 432.20 Y 658.00 --- --- --- ---
Ar41 Argon 1.83 H 59.50 --- --- --- ---
As72 Arsenic 26.00 H --- --- --- --- ---
As74 Arsenic 17.78 D 511.00 834.00 --- --- ---
As76 Arsenic 26.32 H 595.80 511.00 634.80 --- ---
Au198 Gold 2.70 D 559.08 657.03 1217.70 --- ---
Au199 Gold 3.14 D 411.80 --- --- --- ---
Ba131 Barium 11.80 D 158.40 72.30 208.20 --- ---
Ba133 Barium 10.50 Y 31.60 496.30 123.80 --- ---
Bi207 Bismuth 32.20 Y 31.60 356.00 81.00 --- ---
Br77 Bromine 56.00 H 569.70 1063.66 76.50 --- ---
C 11 Carbon 20.38 M 239.00 520.70 --- --- ---
Cd109 Cadmium 426.60 D 511.00 --- --- --- ---
Ce139 Cerium 137.60 D 22.60 88.03 --- 53.000% ---
Ce144 Cerium 284.30 D 34.20 165.90 --- --- ---
Co55 Cobalt 17.54 H --- --- --- --- ---
Co57 Cobalt 271.70 D 511.00 931.10 477.20 --- ---
Co58 Cobalt 70.82 D 123.64 14.41 --- 71.000% ---
Co60 Cobalt 5.27 Y 810.80 511.00 --- --- ---
Cr51 Chromium 27.70 D 1173.24 1332.50 --- 6.000% ---
Cs131 Cesium 9.69 D 320.08 --- --- --- ---
Cs132 Cesium 6.47 D 30.40 --- --- --- ---
Cs134 Cesium 2.07 Y --- --- --- --- ---
Cs136 Cesium 13.10 D 604.70 795.80 567.40 --- ---
Cs137 Cesium 30.00 Y 818.50 1048.10 340.60 --- ---
Cu64 Copper 12.70 H 661.66 32.85 --- 12.000% ---
Cu67 Copper 2.58 D 511.00 --- --- --- ---
Dy157 Dysprosium 8.10 H 184.60 93.31 --- --- ---
326.20 45.50 --- --- ---

October 15 APPENDIX – NUCLIDE LIST a-1

CAPINTEC, INC. CAPTUS® 700t

Nuclide Half-Life Photopeak Photopeak Photopeak Well Probe
1 (keV) 2 (keV) 3 (keV) Efficiency Efficiency
Eu152 Europium 13.40 Y
F 18 Fluorine 109.70 M 41.00 122.00 344.28 14.000% ---
Fe52 Iron 8.27 H 511.00 --- --- --- ---
Fe59 Iron 44.51 D 168.70 511.00 --- --- ---
Ga66 Gallium 9.40 H 1099.00 1292.00 --- --- ---
Ga67 Gallium 3.26 D 511.00 1039.90 --- --- ---
Ga68 Gallium 68.00 M 93.31 184.58 300.21 --- ---
Ga72 Gallium 14.10 H --- --- --- --- ---
Hf181 Hafnium 42.40 D 834.00 630.00 --- --- ---
Hg197 Mercury 64.10 H 482.00 133.00 58.80 --- ---
Hg203 Mercury 46.60 D 71.70 --- --- --- ---
I 123 Iodine 13.22 H 279.20 --- --- --- ---
I 124 Iodine 4.18 D 158.97 28.05 --- --- ---
I 125 Iodine 59.60 D 602.72 28.04 511.00 --- ---
I 129 Iodine 15.70 MY 28.40 --- --- --- ---
I 130 Iodine 12.36 H 31.28 --- --- --- ---
I 131 Iodine 8.02 D 536.10 668.50 739.50 --- ---
I 133 Iodine 20.80 H 364.48 637.14 284.30 --- ---
In111 Indium 2.81 D 529.47 875.33 --- --- ---
In113m Indium 1.66 H 171.28 23.62 245.39 --- ---
In116m Indium 54.15 M 391.70 24.70 --- --- ---
Ir192 Iridium 73.83 D --- --- --- --- ---
K 42 Potassium 12.36 H 310.64 468.10 --- --- ---
K 43 Potassium 22.30 H 1524.67 --- --- --- ---
Kr79 Krypton 35.04 H 375.55 617.49 593.40 --- ---
Kr87 Krypton 76.30 M --- --- --- --- ---
Lu177 Lutetium 6.71 D --- --- --- --- ---
Mn52 Manganese 5.59 D --- --- --- --- ---
Mn52m Manganese 21.10 M 1434.10 935.50 744.20 --- ---
Mn54 Manganese 312.50 D 511.00 1434.06 --- --- ---
Mn56 Manganese 2.58 H 834.84 --- --- ---
Mo99 Molybdenum 65.92 H --- --- --- 10.000% ---
N 13 Nitrogen 9.97 M 140.51 749.65 181.05 --- ---
Na22 Sodium 2.60 Y 511.00 --- --- --- ---
Na24 Sodium 14.96 H 511.00 1274.54 --- --- ---
Nd147 Niobium 10.98 D 1368.00 --- --- ---
Np239 Neptunium 2.36 D 39.60 91.20 531.00 16.000% ---
O 15 Oxygen 2.04 M 105.70 --- --- --- ---
P 32 Phosphorus 14.29 D --- --- --- --- ---
Pb203 Lead 51.88 H --- --- --- --- ---
Pb212 Lead 10.64 H 74.40 279.20 --- --- ---
Ra226 Radium 1600.00 Y 238.60 78.70 --- --- ---
Rb81 Rubidium 4.58 H 609.00 352.00 79.20 --- ---
Rb82 Rubidium 1.27 M 511.00 446.10 190.30 --- ---
Rb84 Rubidium 32.77 D --- --- --- --- ---
Sb117 Antimony 2.80 H 881.61 511.00 --- --- ---
Sb122 Antimony 2.70 D --- --- --- --- ---
Sb124 Antimony 60.20 D 564.24 692.65 --- --- ---
Sc44 Scandium 3.93 H 602.73 1690.98 720.17 --- ---
--- --- --- --- ---
---
---

a-2 APPENDIX – NUCLIDE LIST October 15

CAPINTEC, INC. CAPTUS® 700t

Nuclide Half-Life Photopeak Photopeak Photopeak Well Probe
1 (keV) 2 (keV) 3 (keV) Efficiency Efficiency
Sc46 Scandium 83.79 D
Se75 Selenium 119.80 D 889.25 1120.51 --- --- ---
Sn113 Tin 115.10 D 269.10 1120.51 --- --- ---
Sr85 Strontium 64.85 D 391.70 --- --- --- ---
Sr89 Strontium 50.50 D 514.00 --- --- --- ---
Sr90 Strontium 28.50 Y --- --- --- --- ---
Tc99m Technetium 6.01 H --- --- --- --- ---
Tl201 Thallium 72.91 H 140.51 --- --- 71.000% ---
V 48 Vanadium 15.97 D 72.32 167.43 135.34 45.000% ---
Xe133 Xenon 5.24 D 511.00 983.52 --- --- ---
Xe135 Xenon 9.09 H --- --- --- --- ---
Y 86 Yttrium 14.74 H --- --- --- --- ---
Y 88 Yttrium 106.60 D 1076.63 511.00 627.72 --- ---
Y 90 Yttrium 64.00 H 898.00 1836.00 --- --- ---
Yb169 Ytterbium 32.03 D --- --- --- --- ---
Zn65 Zinc 243.90 D 54.01 198.00 177.00 --- ---
Zn69m Zinc 13.76 H 1116.00 511.00 --- --- ---
436.60 --- --- --- ---

October 15 APPENDIX – NUCLIDE LIST a-3

CAPINTEC, INC. CAPTUS® 700t

This page intentionally left blank.

CAPINTEC, INC. CAPTUS® 700t

INDEX

A Results, 9-15, 10-25
ABORT CAL button, 9-5
ABORT LINEARITY CORRECTION Settings, 10-8
Trigger Level, 10-8
button, 9-10 BACKGROUND button, 13-10
Acceptance Testing, 4-7, 8-1 Battery, 16-17
ADD button, 4-16, 6-24, 11-45
ADD LOCATION button, 10-15 low, 16-10
ADD PROTOCOL button, 12-9
Add User, 4-16 Replacement, 16-10
BIO ASSAY button, 3-3, 13-5, 13-19
First Name Field, 4-19 BIO ASSAY REPORT button, 14-61
Last Name Field, 4-19 BioAssay, 2-4
Password (again) Field, 4-19
Password Field, 4-18 Background, 13-24
Role Field, 4-19
UserName Field, 4-17 Count Time, 13-6
Add User Nuclide, 6-24 Cross Contamination, 13-17
adjustments, 1-6
Admin login, 4-8 Detailed Report, 14-66
Administered Dose Measurement, 12-40 Efficiency, 13-9
Administration Date/Time
Enter, 12-44, 12-52 Enter Efficiency, 13-16
ADVANCED DETECTOR button, 6-2, 11- Inactivate Test, 14-67
40, 12-5, 13-3 Measure Efficiency, 13-9
ALL button, 14-5, 14-9, 14-17, 14-21
ALL WIPES button, 14-27, 14-28 Measurements, 13-19
Alphanumeric Data Neck Measurement, 13-24
entering, 3-6
Auto Calibrate, 9-2 Nuclide, 13-7
AUTO CALIBRATE button, 3-3, 9-3 Probe Distance, 13-7, 13-23
Auto Calibration Report, 14-61
Detailed Report, 14-7
Drilled Probe, 9-7 Results, 13-24
Probe or Well, 9-5 Setup, 13-3
Report, 14-3
Summary Report, 14-7 Setup ROI, 13-8
AUTO CALIBRATION REPORT button, Staff, 13-19
14-3 Summary Report, 14-65

B Trigger Levels, 13-7
Background, 9-11, 10-23 BioAssay Module, 13-1

BioAssay, 13-24 Blood samples, counting, 10-32
Count Time, 9-13, 10-9, 10-24 Blood Tests, 2-4
Measure, 10-23
Measurement, 9-14, 10-25 Plasma Volume, 2-4
RBC Survival, 11-58
RBC Survival, 2-4, 11-40
RBC Volume, 2-4
BLUE ARROW button, 9-15, 9-23, 9-39,
10-25, 10-31, 10-37, 11-12, 11-26, 11-
39, 11-62, 12-58, 14-15, 14-20, 14-25,
14-32, 14-37, 14-41, 14-45, 14-51, 14-
60, 14-68
Brightness, 5-19
button
ABORT CAL, 9-5
ABORT LINEARITY CORRECTION, 9-

10
ADD, 4-16, 6-24, 11-45

October 15 INDEX i-1

CAPINTEC, INC. CAPTUS® 700t

ADD LOCATION, 10-15 14-25, 14-32, 14-37, 14-41, 14-45,
ADD PROTOCOL, 12-9
ADVANCED DETECTOR, 6-2, 11-40, 14-51, 14-60, 14-68
DOWN ARROW (▼), 3-7, 6-13, 9-29,
12-5, 13-3
10-11, 10-19, 10-20, 10-21, 10-27,
ALL, 14-5, 14-9, 14-17, 14-21
ALL WIPES, 14-27, 14-28 10-35, 11-52, 12-3, 12-15, 12-16, 12-
AUTO CALIBRATE, 3-3, 9-3
AUTO CALIBRATION REPORT, 14-3 20, 12-33, 13-21, 14-6, 14-10, 14-18,
BACKGROUND, 13-10
BIO ASSAY, 3-3, 13-5, 13-19 14-22, 14-29, 14-35, 14-39, 14-43,
BIO ASSAY REPORT, 14-61
BLUE ARROW, 9-15, 9-23, 9-39, 10-25, 14-47, 14-53, 14-63, 14-65, 15-4

10-31, 10-37, 11-12, 11-26, 11-39, EDIT, 4-13, 4-20, 4-22, 6-13, 6-29, 11-
53, 12-34
11-62, 12-58, 14-15, 14-20, 14-25,
14-32, 14-37, 14-41, 14-45, 14-51, EDIT BACKGROUND TRIGGER, 10-8
14-60, 14-68 EDIT DEFAULT PACKAGE
Cal with Cs137, 9-5
CALCULATE, 9-30, 11-11, 11-23, 11- SETTINGS, 10-14
37 EDIT DEFAULT SEALED SETTINGS,

CDC, 5-17 10-13
CHI SQUARE REPORT, 14-21 EDIT DEFAULT UNRESTRICTED
CHI SQUARE TEST, 9-33
CHI SQUARE TEST AS PROBE, 9-33 AREA SETTINGS, 10-12
CHI SQUARE TEST AS WELL, 9-33 EDIT DEFAULT WORK AREA
CLEAR, 6-15, 11-44
CLEAR ROW, 13-16 SETTINGS, 10-10
CLEAR SELECTED NUCLIDE, 10-11, EDIT LOCATION, 10-20
EDIT PROTOCOL, 12-15
10-19 EDIT WIPE FULL SPECTRUM

COMPLETE, 11-62, 12-59 EFFICIENCY, 6-12
CONTINUE, 2-5, 4-7 EFFICIENCIES, 6-11
COUNT TIME, 6-21, 9-13, 9-19, 9-27, ENTER ADMINISTRATION

10-24, 10-28, 10-33, 11-5, 11-8, 11-9, DATE/TIME, 12-44
ENTER EFFICIENCY, 13-16
11-16, 11-19, 11-20, 11-21, 11-29, EXIT, 13-20, 13-24
GENERAL MEASUREMENT, 10-32
11-32, 11-33, 11-34, 11-35, 13-14 GENERAL MEASUREMENT AS

Cs137 in Drilled Center, 9-7 PROBE, 10-32
Cs137 on Perimeter, 9-8 GENERAL MEASUREMENT AS
DATE FORMAT, 5-5
DATE/TIME, 3-4 WELL, 10-32
DELETE, 11-54, 12-35 GREEN ARROW, 9-23, 9-39, 10-31, 11-
DELETE LOCATION, 10-21
DELETE NUCLIDE, 6-30 12, 11-26, 11-39, 11-62, 12-58, 14-15,
DELETE PROTOCOL, 12-16 14-20, 14-25, 14-32, 14-37, 14-41,
DETECTOR, 3-4, 6-5, 9-4
DIAGNOSTICS, 7-2 14-45, 14-51, 14-60, 14-68
DOUBLE ARROW, 9-15, 9-23, 9-39, HIGH ACTIVITY, 14-28
INACTIVATE, 14-13, 14-20, 14-25, 14-
10-25, 10-31, 10-37, 11-6, 11-8, 11-9,
32, 14-37, 14-41, 14-45, 14-68
11-12, 11-17, 11-20, 11-21, 11-22,
LAB TESTS, 3-4, 11-2
11-26, 11-30, 11-33, 11-34, 11-35, LEFT DOUBLE ARROW, 10-27
LEFT SINGLE ARROW, 10-27
11-39, 11-62, 12-58, 14-15, 14-20, LEGACY, 5-17
Linearity Correction with Eu152, 9-10
LOAD ORIGINAL VALUES, 13-9
LOGIN, 2-5, 4-6, 4-10, 4-23, 4-25, 4-26
Login as Guest, 4-26
MDA REPORT, 14-16
MDA TEST, 9-25

i-2 INDEX October 15

CAPINTEC, INC. CAPTUS® 700t

MDA TEST AS PROBE, 9-25 RIGHT DOUBLE ARROW, 10-27
MDA TEST AS WELL, 9-25 RIGHT SINGLE ARROW, 10-27
MEASURE, 6-16, 6-21, 9-14, 9-20, 9- RUN, 11-55, 11-61, 11-62, 12-36, 12-

27, 9-35, 10-25, 10-29, 10-37, 11-6, 44, 12-46, 12-48, 12-52, 12-55, 12-56,

11-8, 11-9, 11-17, 11-20, 11-21, 11- 12-59

30, 11-32, 11-33, 11-34, 11-35, 13-14 SAVE, 11-13, 11-14, 11-27, 11-39, 11-
40, 13-25
MEASURE ADMINISTERED DOSE,
12-40 SAVE AND PRINT, 13-26
SAVE EFFICIENCY, 6-23
MEASURE BACKGROUND, 9-13, 10- SAVE WIPE, 10-30
SCHILLING, 11-3
23, 10-27 SCHILLING REPORT, 14-33
SCREEN CALIB, 5-20
Measure Cs137, 9-35 SEALED SOURCE, 14-28
MEASURE EFFICIENCY, 13-9 SEARCH, 11-53, 12-34, 14-6, 14-10,
MEASURE LIST, 10-28
MEASURE PATIENT, 11-56, 12-49, 12- 14-17, 14-22, 14-28, 14-34, 14-39,
14-42, 14-47, 14-48, 14-53, 14-54,
52 14-64

MEASURE PRE-DOSE PATIENT, 12- SELECT, 13-21, 14-63
37 SELECT PROTOCOL, 12-21
SETUP, 3-4, 4-9, 4-25, 6-2, 9-18, 12-5,
MEASURE RESIDUAL LIQUID, 12-46
MEASURE SOURCE, 6-20 13-3
MEASURE WIPES, 10-26
MEASUREMENT, 3-3, 9-11, 10-4 SETUP BIOASSAY ROI, 13-8
NEXT, 13-24 SETUP LOCATION, 10-15
NO, 14-14, 14-20, 14-25, 14-32, 14-37, SINGLE ARROW, 9-15, 9-24, 9-39, 10-

14-41, 14-45, 14-50, 14-57, 14-68 25, 10-31, 10-37, 11-6, 11-8, 11-9,
NORMAL VALUES, 12-25, 14-58
NUCLIDE/ROI, 10-34 11-13, 11-17, 11-20, 11-21, 11-22,
PACKAGE, 14-28
PLASMA, 11-14 11-26, 11-30, 11-33, 11-34, 11-35,
PLASMA REPORT, 14-38
PRINT, 5-7, 6-22, 9-23, 9-32, 9-38, 10- 11-39, 11-62, 12-58, 14-15, 14-20,
14-25, 14-32, 14-37, 14-41, 14-45,
31, 10-38, 11-12, 11-25, 11-38, 11-61,
14-51, 14-60, 14-68
12-55, 14-7, 14-8, 14-11, 14-12, 14- SKIP ALL WIPES, 10-28, 10-30
SKIP PRE-DOSE, 12-38
18, 14-19, 14-23, 14-24, 14-29, 14-31, SKIP WIPE, 10-28, 10-30
SPECTRUM, 9-23, 9-32, 10-31, 14-14,
14-35, 14-36, 14-39, 14-40, 14-43,
14-20, 14-32
14-44, 14-49, 14-56, 14-65, 14-67
STAFF, 4-9, 4-25
PRINT ALL, 12-17 STOP, 6-21, 9-14, 9-20, 9-27, 9-36, 10-
PRINT PROTOCOL, 12-17
PROBE, 6-5, 9-5, 14-5, 14-9, 14-17, 14- 25, 10-29, 10-37, 11-6, 11-8, 11-9,

21 11-17, 11-20, 11-21, 11-22, 11-30,
QUALITY ASSURANCE, 3-3, 9-16
RBC, 11-28 11-32, 11-33, 11-34, 11-35, 13-14
RBC REPORT, 14-42
RBC SURVIVAL, 11-44 SYSTEM TEST, 9-18
RBC SURVIVAL NORMAL VALUES, SYSTEM TEST AS PROBE, 9-18
SYSTEM TEST AS WELL, 9-18
11-42 SYSTEM TEST REPORT, 14-8
RBC SURVIVAL REPORT, 14-46 TEST, 5-21
REACTIVATE, 14-49, 14-56 TEST SOURCE, 6-6
REPORT, 10-30 THYROID UPTAKE, 3-4, 12-2, 12-7
REPORTS, 3-3, 14-2 THYROID UPTAKE NORMAL
RESTORE ORIGINAL ROI, 12-14
VALUES, 12-17

October 15 INDEX i-3

CAPINTEC, INC. CAPTUS® 700t

THYROID UPTAKE REPORT, 14-52 CHI SQUARE TEST button, 9-33
UNRESTRICTED AREA, 14-28 Chi Square Test Report, 14-21
UP ARROW (▲), 3-7, 6-13, 9-29, 10- Choosing Date Format, 5-5
Ci / Bq
11, 10-19, 10-20, 10-21, 10-27, 10-35,
11-52, 12-3, 12-15, 12-16, 12-20, 12- Choosing, 5-4
33, 13-21, 14-7, 14-10, 14-18, 14-23, Conversion, 15-2
14-29, 14-35, 14-39, 14-43, 14-47, Cleaning, 16-1, 16-2
14-53, 14-63, 14-65, 15-4 Cleaning Instructions, 16-2
USER NUCLIDES, 6-24 CLEAR button, 6-15, 11-44
UTILITY, 3-4, 4-23, 4-26, 7-1, 15-1 CLEAR ROW button, 13-16
VIEW, 12-24, 14-7, 14-11, 14-19, 14-23, CLEAR SELECTED NUCLIDE button, 10-
14-30, 14-35, 14-40, 14-44, 14-49, 11, 10-19, 10-35
14-54, 14-55, 14-66 Collimator Block Inspection, 16-6
VIEW NORMAL, 11-60, 14-50 Communications Device Class, 5-17
VIEW PROTOCOL, 14-57 COMPLETE button, 11-62, 12-59
WELL, 6-5, 9-5, 14-5, 14-9, 14-17, 14- Completing a Patient, 11-62, 12-59
21 Contamination Test, 8-2
WILDCARD (%), 11-52, 11-53, 12-33, CONTINUE button, 2-5, 4-7
12-34, 14-47, 14-48, 14-53, 14-54 Correction Factor
WIPE REPORT, 14-26 MDA Test, 9-30
WIPE TESTS, 10-4 Count Time, 9-1
WORK AREA, 14-28 Background, 9-13, 10-9, 10-24
YES, 14-14, 14-20, 14-25, 14-32, 14-37, BioAssay, 13-6
14-41, 14-45, 14-50, 14-56, 14-68 General Measurement, 10-33
System Test, 9-19, 9-27
C Wipe Location, 10-18
Cal with Cs137 button, 9-5 Wipe Test, 10-28
CALCULATE button, 9-30, 11-11, 11-23, Work Area, 10-11
COUNT TIME button, 6-21, 9-13, 9-19, 9-
11-37 27, 10-24, 10-28, 10-33, 11-5, 11-8, 11-
Calculation Utilities, 15-1 9, 11-16, 11-19, 11-20, 11-21, 11-29,
11-32, 11-33, 11-34, 11-35, 13-14
Ci /Bq Conversion, 15-2 Counting Methods, 12-10
Decay Calculator, 15-4 Decay Correct Administered Dose, 12-
Cautions and Notes, 1-6
CDC, 5-17 10
CDC button, 5-17 Measure Same Reference Dose Before
Changing Detector, 6-5, 9-4
Changing Users, 4-23 Each Uptake, 12-10
CHI SQUARE REPORT button, 14-21 Cross Contamination, 13-17
Chi Square Test, 9-32 Cs137 in Drilled Center button, 9-7
Detailed Report, 14-23 Cs137 on Perimeter button, 9-8
Duration, 9-34
Inactivate, 14-24 D
Measurement, 9-35 Date
Number of Samples, 9-34
Results, 9-38 entering, 5-1
Summary Report, 14-23 DATE FORMAT button, 5-5
CHI SQUARE TEST AS PROBE button, DATE/TIME button, 3-4
9-33 Date/Time Screen, 3-8
CHI SQUARE TEST AS WELL button, 9- Dead Time, 9-2
33 Decay Calculator, 15-4

Activity, 15-4

i-4 INDEX October 15

CAPINTEC, INC. CAPTUS® 700t

Date, 15-4 Number/Factor, 12-32
Results, 15-8 Dose Form, 12-12
Select Nuclide, 15-4 Dose Hematocrit %
Decay Correct Administered Dose, 12-10
DELETE button, 11-54, 12-35 RBC Test, 11-31
DELETE LOCATION button, 10-21 Dose Measurement, 12-11
DELETE NUCLIDE button, 6-30 DOUBLE ARROW button, 9-15, 9-23, 9-
DELETE PROTOCOL button, 12-16
Delete User Nuclide, 6-30 39, 10-25, 10-31, 10-37, 11-6, 11-8, 11-
Deleting Patient, 11-54, 12-35 9, 11-12, 11-17, 11-20, 11-21, 11-22,
Deleting Wipe Location, 10-21 11-26, 11-30, 11-33, 11-34, 11-35, 11-
Description 39, 11-62, 12-58, 14-15, 14-20, 14-25,
Functional, 2-2 14-32, 14-37, 14-41, 14-45, 14-51, 14-
Technical, 2-8 60, 14-68
Detailed Report DOWN ARROW (▼) button, 3-7, 6-13, 9-
Auto Calibration, 14-7 29, 10-11, 10-19, 10-20, 10-21, 10-27,
BioAssay, 14-66 10-35, 11-52, 12-3, 12-15, 12-16, 12-20,
Chi Square Test, 14-23 12-33, 13-21, 14-6, 14-10, 14-18, 14-22,
MDA Test, 14-18 14-29, 14-35, 14-39, 14-43, 14-47, 14-
Plasma Test, 14-39 53, 14-63, 14-65, 15-4
RBC Test, 14-44 Duration
Schilling Test, 14-35 Chi Square, 9-34
System Test, 14-11
Thyroid Uptake Test, 14-55 E
Wipe Test, 14-30 EDIT BACKGROUND TRIGGER button,
Detector
Changing, 6-5, 9-4 10-8
DETECTOR button, 3-4, 6-5, 9-4 EDIT button, 4-13, 4-20, 4-22, 6-13, 6-29,
Detector Indicator, 3-4
Detectors 11-53, 12-34
Description, 2-8 EDIT DEFAULT PACKAGE SETTINGS
Probe, 2-11
Well, 2-11 button, 10-14
Diagnostics, 7-1 EDIT DEFAULT SEALED SETTINGS
DIAGNOSTICS button, 7-2
Dimensions button, 10-13
Isolation Transformer, 2-10 EDIT DEFAULT UNRESTRICTED AREA
Probe Detector, 2-11
Readout Unit, 2-10 SETTINGS button, 10-12
Thyroid Uptake Stand, 2-9 EDIT DEFAULT WORK AREA
Well Detector, 2-11
Disinfecting, 16-2 SETTINGS button, 10-10
Disinfecting Instructions, 16-2 EDIT LOCATION button, 10-20
disposal, 16-4 EDIT PROTOCOL button, 12-15
Dosage Edit User, 4-20
Activity, 11-48, 12-30 Edit User Nuclide, 6-29
Calibration Date, 11-49, 12-31 EDIT WIPE FULL SPECTRUM
Information, 11-48, 12-29
Injection Date, 11-51 EFFICIENCY button, 6-12
Lot Number, 11-50, 12-32 Editing Wipe Location, 10-20
EFFICIENCIES button, 6-11
Efficiency

BioAssay, 13-9
Data, 6-10
Input, 6-15
Measure, 6-16
Nuclide, 6-13
Source Activity Field, 6-19
Source Calibrated On Field, 6-18

October 15 INDEX i-5

CAPINTEC, INC. CAPTUS® 700t

Wipe Full Spectrum, 6-11 Hematocrit
Electromagnetic Interference, 1-7 RBC Survival, 11-57
Element Field
Hematocrit %
User Nuclide, 6-26 Plasma Test, 11-19
EMI, 1-7, 5-7
Energy(keV), 6-15 HID, 5-17
Energy1(keV) Field HIGH ACTIVITY button, 14-28
Human Interface Device, 5-17
User Nuclide, 6-26
Energy2(keV) Field I
Identify nuclides, 2-2
User Nuclide, 6-27 Inactivate
Energy3(keV) Field
BioAssay Test, 14-67
User Nuclide, 6-27 Chi Square Test, 14-24
Enhanced Security Status, 4-8 MDA Test, 14-19
ENTER ADMINISTRATION DATE/TIME Plasma Test, 14-40
RBC Test, 14-44
button, 12-44 Schilling Test, 14-36
ENTER EFFICIENCY button, 13-16 System Test, 14-12
Environment Requirements, 2-11, 4-5 User, 4-22
Wipe Test, 14-31
Operational, 4-5 INACTIVATE button, 14-13, 14-20, 14-25,
Storage, 4-5 14-32, 14-37, 14-41, 14-45, 14-68
EXIT button, 13-20, 13-24 Initialization
Detector, 6-1
F Input Efficiency, 6-15
Full Spectrum Efficiency, 2-3 BioAssay, 13-16
Functional Description, 2-2 Inspection
functions, 2-5 Spring-Arm, 16-6
Fuse Servicing, 16-8 Intended Use, 2-1

Power Line Fuses, 16-8 L
Lab Tests, 2-3, 11-1
G
General Measurement Blood Tests, 2-4
Plasma Volume (I125), 11-14
Count Time, 10-33 RBC Survival Test, 11-40
Measuring, 10-37 RBC Volume (Cr51), 11-28
Results, 10-38 Schilling, 11-3
Set Nuclide/ROI, 10-34 Urine, 2-3
GENERAL MEASUREMENT AS PROBE LAB TESTS button, 3-4, 11-2
button, 10-32 Labeling, 1-2
GENERAL MEASUREMENT AS WELL Labels
button, 10-32 High Voltage, 1-5
GENERAL MEASUREMENT button, 10- Shipping, 16-19
32 LEFT DOUBLE ARROW button, 10-27
general operating instructions, 3-1 LEFT SINGLE ARROW button, 10-27
GREEN ARROW button, 9-23, 9-39, 10- Legacy, 5-17
31, 11-12, 11-26, 11-39, 11-62, 12-58, LEGACY button, 5-17
14-15, 14-20, 14-25, 14-32, 14-37, 14- LIFETIME, 1-8
41, 14-45, 14-51, 14-60, 14-68 Linearity Correction with Eu152 button,
Guest login, 4-8 9-10

H
Halflife Field

User Nuclide, 6-26

i-6 INDEX October 15

CAPINTEC, INC. CAPTUS® 700t

List Screen, 3-7 MEASURE PRE-DOSE PATIENT button,
Live Time, 9-1 12-37
LOAD ORIGINAL VALUES button, 13-9
Locations, 10-27 MEASURE RESIDUAL LIQUID button,
login 12-46

Admin, 4-8 Measure Same Reference Dose Before
Guest, 4-8 Each Uptake, 12-10
root, 4-8
User, 4-8 Measure Single Dose Screen, 12-41
Login MEASURE SOURCE button, 6-20
root, 4-10 Measure Wipes, 10-26
Login as Guest button, 4-26 MEASURE WIPES button, 10-26
LOGIN button, 2-5, 4-6, 4-10, 4-23, 4-25, Measured Background
4-26
Low Battery, 16-10 MDA Test, 9-26
Plasma Test, 11-15
M RBC Test, 11-29
Main Screen, 3-2 Schilling Test, 11-5
maintenance, 16-1 Measured Plasma Sample
MDA REPORT button, 14-16 Plasma Test, 11-21
MDA Test, 9-24 RBC Test, 11-35
Measured Plasma Standard
Correction Factor, 9-30 RBC Test, 11-33
Detailed Report, 14-18 Measured Standard
Inactivate, 14-19 Plasma Test, 11-19
Measured Background, 9-26 Schilling Test, 11-8
Nuclide, 9-29 Measured Urine Aliquot
Precision Factor, 9-29 Schilling Test, 11-9
Report, 14-16 Measured Whole Blood Sample
Results, 9-30 Plasma Test, 11-20
Summary Report, 14-18 RBC Test, 11-34
MDA TEST AS PROBE button, 9-25 Measured Whole Blood Standard
MDA TEST AS WELL button, 9-25 RBC Test, 11-32
MDA TEST button, 9-25 Measurement
MEASURE ADMINISTERED DOSE General Category, 10-32
button, 12-40 MEASUREMENT button, 3-3, 9-11, 10-4
Measure Background, 10-23 Measurement List, 10-27
MEASURE BACKGROUND button, 9-13, Measurement Protocols, 12-5
10-23, 10-27 Deleting, 12-16
MEASURE button, 6-16, 6-21, 9-14, 9-20, Measuring General Sample, 10-37
9-27, 9-35, 10-25, 10-29, 10-37, 11-6, Measuring Wipes, 10-28
11-8, 11-9, 11-17, 11-20, 11-21, 11-30, Minimum Detectable Activity Test, 9-24
11-32, 11-33, 11-34, 11-35, 13-14 Mutlichannel Analyzer, 2-8
Measure Cs137 button, 9-35
Measure Efficiency, 6-16 N
BioAssay, 13-9 Neck Measurement
MEASURE EFFICIENCY button, 13-9
MEASURE LIST button, 10-28 BioAssay, 13-24
Measure Patient, 12-48, 12-52 NEXT button, 13-24
MEASURE PATIENT button, 11-56, 12- NO button, 14-14, 14-20, 14-25, 14-32,
49, 12-52
14-37, 14-41, 14-45, 14-50, 14-57, 14-
68
Normal Values
Clearing, 11-44

October 15 INDEX i-7

CAPINTEC, INC. CAPTUS® 700t

Maximum Days, 11-43 Photopeaks
Minimum Days, 11-43 primary, 6-15, 6-26
RBC Survival, 11-40
Thyroid Uptake, 12-17 setting, 6-15
NORMAL VALUES button, 12-25, 14-58 PLASMA button, 11-14
Nuclide PLASMA REPORT button, 14-38
BioAssay, 13-7 Plasma Test, 11-14
Efficiency, 6-13
Nuclide Field, 6-25 calculation, 11-24
User Nuclide, 6-25
NUCLIDE/ROI button, 10-34 Detailed Report, 14-39
Nuclides Hematocrit %, 11-19
Wipe Location, 10-18
Work Area, 10-11 Inactivate, 14-40
Numeric Data Measured Background, 11-15
entering, 3-5 Measured Plasma Sample, 11-21

O Measured Standard, 11-19
Operational Setup, General, 4-7 Measured Whole Blood Sample, 11-20
Operator
Patient Weight, 11-19
Profile, 2-2 Report, 14-38
Training, 2-2
Results, 11-23
P Sample Volume, 11-18
Package Save, 11-27

Settings, 10-14 Standard Dilution Factor, 11-18
PACKAGE button, 14-28 Summary Report, 14-39
Password
Plasma Volume (I125) Test, 11-14
root, 4-13 Plasma Volume Test, 2-4
Patient Power Requirements, 4-5

Adding, 12-20 Precision Factor
Completing, 11-62, 12-59 MDA Test, 9-29
Date of Birth (DOB), 11-47, 12-27
Deleting, 11-54, 12-35 Pre-Dose, 12-12
Editing, 11-52, 12-33 Pre-Dose Measurement, 12-36, 12-51
First Name, 11-45, 12-26 Preventative Maintenance, 16-3
ID, 11-47, 12-27
Last Name, 11-46, 12-27 primary photopeak, 6-22, 13-15
Measure, 12-48, 12-52 PRINT ALL button, 12-17
Physician, 11-48, 12-28 PRINT button, 5-7, 6-22, 9-23, 9-32, 9-38,
Sex, 11-47, 12-28
Technologist, 11-48, 12-29 10-31, 10-38, 11-12, 11-25, 11-38, 11-
Viewing, 11-52, 12-33 61, 12-55, 14-7, 14-8, 14-11, 14-12, 14-
Patient Hematocrit %
RBC Test, 11-31 18, 14-19, 14-23, 14-24, 14-29, 14-31,
Patient Information, 11-45, 12-20, 12-26 14-35, 14-36, 14-39, 14-40, 14-43, 14-
RBC Survival, 11-44
Patient Weight 44, 14-49, 14-56, 14-65, 14-67
Plasma Test, 11-19 PRINT PROTOCOL button, 12-17
RBC Test, 11-32 printer

power requirements, 5-7
selection, 5-8

Printing, 5-7
PROBE button, 6-5, 9-5, 14-5, 14-9, 14-

17, 14-21
Probe Distance

BioAssay, 13-7, 13-23

Protocols, 12-13, 12-23
Probe Efficiency(%) Field, 6-27

Profile
Operator, 2-2

i-8 INDEX October 15

CAPINTEC, INC. CAPTUS® 700t

Program Flow, 2-6 Patient Sex, 11-47
Protected Modules, 4-8 Patient Technologist, 11-48
Protocols
Reactivate a Patient, 14-49
Adding, 12-9 Report, 14-46
Counting Methods, 12-10 RBC SURVIVAL button, 11-44
Counting Time, 12-13, 12-22 RBC SURVIVAL NORMAL VALUES
Deleting, 12-16 button, 11-42
Dose Form, 12-12 RBC SURVIVAL REPORT button, 14-46
Dose Measurement, 12-11 RBC Survival Test
Editing, 12-15
Location Name, 12-9 Report, 14-49
Nuclide, 12-12 RBC Test, 11-28
Pre-Dose, 12-12
Printing Report, 12-17 calculation, 11-37
Probe Distance, 12-13, 12-23
Residual, 12-13 Detailed Report, 14-44
Restore Original ROI, 12-14 Dose Hematocrit %, 11-31
ROI Selection, 12-14
Save, 12-14 Inactivate, 14-44
View, 12-24, 12-55, 14-57 Measured Background, 11-29

Q Measured Plasma Sample, 11-35
Quality Assurance Measured Plasma Standard, 11-33
Measured Whole Blood Sample, 11-34
System Test, 9-18
QUALITY ASSURANCE button, 3-3, 9-16 Measured Whole Blood Standard, 11-32
Quality Assurance Tests, 8-1, 9-16 Patient Hematocrit %, 11-31

R Patient Weight, 11-32
Radiochromatography Report, 14-42
Results, 11-37
counting strips, 10-32
RBC button, 11-28 Save, 11-39
RBC REPORT button, 14-42 Summary Report, 14-43
RBC Survival, 2-4, 11-40
RBC Volume (Cr51) Test, 11-28
Background, 11-58 RBC Volume Test, 2-4
Count Time, 11-51 Reactivate
Dosage Activity, 11-48
Dosage Calibration Date, 11-49 Patient, 14-49, 14-56
Dosage Information, 11-48 User, 4-22
Dosage Injection Date, 11-51 REACTIVATE button, 14-49, 14-56
Dosage Lot Number, 11-50 Real Time, 9-1
Hematocrit, 11-57 recalibration, 1-7
Making Measurements, 11-55
Normal Values, 11-40 Receiving Condition Examination, 4-1
Patient Date of Birth (DOB), 11-47 Region of Interest, 6-10, 6-15, 6-26, 9-23,
Patient First Name, 11-45
Patient ID, 11-47 9-39, 10-31, 10-34, 11-12, 11-26, 11-39,
Patient Information, 11-44, 11-45 11-62, 12-14, 12-58, 14-15, 14-20, 14-
Patient Last Name, 11-46 25, 14-32, 14-37, 14-41, 14-45, 14-51,
Patient Physician, 11-48 14-60, 14-68
Patient Report, 11-60 Regions of Interest

BioAssay, 13-8
Regulatory Listings, 2-13

Replacement Parts, 16-18
Report

Auto Calibration, 14-3

Auto Calibration Detailed, 14-7
Auto Calibration Summary, 14-7

BioAssay, 14-61

BioAssay Detailed, 14-66

October 15 INDEX i-9

CAPINTEC, INC. CAPTUS® 700t

BioAssay Summary, 14-65 Results
BioAssay Test Spectrum, 14-68 BioAssay, 13-24
Chi Square Test, 9-38, 14-21 Chi Square Test, 9-38
Chi Square Test Detailed, 14-23 General Measurement, 10-38
Chi Square Test Spectrum, 9-39, 14-25 MDA Test, 9-30
Chi Square Test Summary, 14-23 Plasma Test, 11-23
Diagnostics, 7-2 RBC Test, 11-37
Efficiency, 6-22 Schilling Test, 11-11
General Measurement, 10-38 System Test, 9-22
MDA Test, 9-32, 14-16 Wipe Test, 10-30
MDA Test Detailed, 14-18
MDA Test Spectrum, 14-20 RIGHT DOUBLE ARROW button, 10-27
MDA Test Summary, 14-18 RIGHT SINGLE ARROW button, 10-27
Plasma Test, 11-25, 14-38 ROI, 6-15, 6-22, 6-26, 9-23, 9-39, 10-31,
Plasma Test Detailed, 14-39
Plasma Test Spectrum, 14-41 10-34, 10-36, 11-12, 11-26, 11-39, 11-
Plasma Test Summary, 14-39 62, 12-14, 12-58, 13-15, 14-15, 14-20,
Protocols, 12-17 14-25, 14-32, 14-37, 14-41, 14-45, 14-
RBC Surtvival Test, 14-49 51, 14-60, 14-68
RBC Survival, 14-46 BioAssay, 13-8
RBC Survival Test, 14-49 ROI Selection
RBC Test, 11-38, 14-42 Protocols, 12-14
RBC Test Detailed, 14-44 root login, 4-8
RBC Test Spectrum, 14-45 RUN button, 11-55, 11-61, 11-62, 12-36,
RBC Test Summary, 14-43 12-44, 12-46, 12-48, 12-52, 12-55, 12-
Schilling Test, 11-12, 14-33 56, 12-59
Schilling Test Detailed, 14-35
Schilling Test Spectrum, 14-37 S
Schilling Test Summary, 14-35 Safety, 1-1
System Test, 8-1, 9-23, 14-8 Safety Tips, 1-8
System Test Detailed, 14-11 Sample Volume
System Test Spectrum, 9-24, 14-15
System Test Summary, 14-11 Plasma Test, 11-18
Thyroid Uptake, 14-52 Save
Thyroid Uptake Test Detailed, 14-55
Wipe Test, 10-31, 14-26 Plasma Test, 11-27
Wipe Test Detailed, 14-30 RBC Test, 11-39
Wipe Test Spectrum, 10-31, 14-32 Schilling Test, 11-13
Wipe Test Summary, 14-29 SAVE AND PRINT button, 13-26
REPORT button, 10-30 SAVE button, 11-13, 11-14, 11-27, 11-39,
REPORTS button, 3-3, 14-2 11-40, 13-25
Reports Module, 14-1 SAVE EFFICIENCY button, 6-23
Requirements Save Protocol, 12-14
Environment, 2-11, 4-5 SAVE WIPE button, 10-30
Power, 2-12, 4-5 Saving Wipe Location, 10-19
Residual, 12-13 SCHILLING button, 11-3
Measurement, 12-46, 12-52 SCHILLING REPORT button, 14-33
Restore Original ROI Schilling Test, 2-3, 11-3
Protocols, 12-14 calculation, 11-11
RESTORE ORIGINAL ROI button, 12-14 Detailed Report, 14-35
Inactivate, 14-36
Measured Background, 11-5
Measured Standard, 11-8
Measured Urine Aliquot, 11-9

i-10 INDEX October 15

CAPINTEC, INC. CAPTUS® 700t

Report, 14-33 BioAssay Setup, 13-6
Results, 11-11 BioAssay Test Report, 14-67
Save, 11-13 BioAssay, Admin User, 13-20
Standard Dilution Factor, 11-8 BioAssay, Non-Admin, 13-19
Summary Report, 14-35 BioAssay, Staff Member Selected, 13-
Urine Aliquot Volume, 11-7
Urine Volume, 11-7 23
Screen Chi Square Test, 9-33
Add New User – Admin, 4-17 Chi Square Test Measurement, 9-35
Add New User – root, 4-16 Chi Square Test Measurement
Add New Wipe Location, 10-16
Add New Wipe Location with Type Complete, 9-37
Chi Square Test Measurement In
Selected, 10-17
Add RBC Survival Test, 11-45 Progress, 9-36
Add Thyroid Uptake Protocol, 12-9
Add Thyroid Uptake Test, 12-22 Chi Square Test Result, 14-24
Add User Nuclide, 6-25 Chi Square Test Results, 9-38, 9-39
Add, Edit, Delete Wipe Location, 10-20 Chi Square Tests Search after Search,
Additional Test Information, 11-13, 11-
14-22
27, 11-39 Chi Square Tests Search with
Advanced Detector Setup, 6-4, 10-4, 11-
Highlighted Test, 14-23
42, 12-7, 13-5 Complete Patient, 12-59
Alphanumeric Keypad, 3-6, 4-12, 4-18, Complete Patient Confirmation, 12-60
Complete RBC Survival Test
11-46, 12-26, 14-14
Auto Calibrate, 9-4 Confirmation, 11-63
Auto Calibrate Measurement, 9-6 Date Format Selection, 5-5
Auto Calibrate with Drilled Probe – After Date/Time, 3-8, 6-8, 6-18, 11-50, 12-31,

both FWHM, 9-9 13-13, 15-5, 15-7
Auto Calibrate with Drilled Probe – Decay Calculator Results, 15-8
Delete Thyroid Uptake Protocol, 12-16
Drilled Center, 9-7 Delete Wipe Location, 10-22
Auto Calibrate with Drilled Probe – Detector Selection, 6-5, 9-5, 14-5
Edit Background Trigger, 10-8
Perimeter, 9-8 Edit Default Package Settings, 10-14
Auto Calibrate with Eu152 Results, 9-10 Edit Default Sealed Settings, 10-13
Auto Calibration Report, 14-8 Edit Default Unrestricted Area Settings,
Auto Calibration Search, 14-3
Auto Calibration Search after Search, 10-12
Edit Default Work Area Settings, 10-10
14-6 Edit Efficiencies, 6-23
Auto Calibration Search with Highlighted Edit Efficiencies – with Default

Calibration, 14-7 Photopeaks, 6-14
Background Measurement, 9-13, 10-23, Edit Efficiencies – without Default

11-5, 11-16, 11-29 Photopeaks, 6-14
Background Measurement Results, 9- Edit Patient Information, 11-54, 12-35
Edit User – Admin, 4-21
15, 10-25 Edit User – root, 4-15, 4-21
BioAssay Efficiency Measurement, 13- Edit User Nuclide, 6-30
Efficiencies Setup, 6-11
14 Enter Activity, 6-9, 6-19, 11-49, 12-30,
BioAssay Report, 13-25
BioAssay Search, Staff Member 13-12, 15-3, 15-6
Enter Administration Date/Time, 12-44
Selected, 14-64 Enter BioAssay Efficiency, 13-16
BioAssay Search, Staff Member Tests, Enter Current Time, 5-3

14-65

October 15 INDEX i-11

CAPINTEC, INC. CAPTUS® 700t

Enter Password, 5-2, 6-3, 11-41, 12-6, Patient Measurement after
13-4 Measurements, 12-51

Enter Serial Number, 6-7 Plasma Test Completed Measurement
Entering Administration Date/Time, 12- Entry, 11-23

45 Plasma Test Measurement Analysis, 11-
Highlighted Patient, 11-53, 12-34 24
Inactivate Record, 14-13
Lab Tests, 11-3 Plasma Test Measurement Entry, 11-15
List, 3-7 Plasma Test Report, 14-40
Login, 4-11, 4-25 Plasma Tests Search, 14-38
Login with Guest button, 4-24 Pre-Dose Measurement, 12-38
Main, 2-6, 3-2, 6-1, 7-1, 9-3, 9-16, 10-2, Protocol Highlighted, 12-21
Quality Assurance – Drilled Probe, 9-17
11-2, 12-2, 13-2, 14-1, 15-1 Quality Assurance – Probe/Well, 9-17
Main showing Low Battery, 16-10 RBC Survival – View Measurements
Main Thyroid Uptake Measurement, 12-
Results, 11-61, 14-51
3, 12-33 RBC Survival After Measurement, 11-58
MDA after Background Measurement, 9- RBC Survival Measurement, 11-57
RBC Survival Measurement Accepted,
30
MDA Background Measurement, 9-26 11-59
MDA Background Measurement RBC Survival Measurement List, 11-44,

Results, 9-28 11-52
MDA Test, 9-25 RBC Survival Measurement with
MDA Test Result, 14-19
MDA Test Results, 9-31 Highlighted Patient, 11-55
MDA Tests Search after Search, 14-17 RBC Survival Report Search with
MDA Tests Search with Highlighted
Highlighted Patient, 14-48
Test, 14-18 RBC Survival Test, 11-56
Measure, 12-37 RBC Survival Test Report, 14-49
Measure Administered Dose, 12-40 RBC Survival Test Search, 14-46
Measure BioAssay Efficiency, 13-11 RBC Survival View Normal Range, 11-
Measure BioAssay Efficiency After
60, 14-50
Measurement, 13-15 RBC Test Completed Measurement
Measure BioAssay Efficiency,
Entry, 11-36
Background, 13-10 RBC Test Measurement Analysis, 11-37
Measure Efficiency, 6-17, 6-20 RBC Test Measurement Entry, 11-28
Measure Efficiency Results, 6-22 RBC Test Report, 14-44
Measure Multi Dose, 12-41 RBC Tests Search after Search, 14-43
Measure Patient, 12-48 Reference Dose and Patient
Measure Residual Liquid, 12-46
Measure Wipe Start, 10-28 Measurement, 12-53
Measure Wipes, 10-26 Reports, 14-2
Measurements – Drilled Probe, 9-12 Residual Liquid Measurement, 12-47
Measurements – Probe/Well, 9-12 Schilling Test Completed Measurement
Multi Dose after Measurements, 12-43
Normal – View Setup, 12-25, 14-58 Entry, 11-10
Normal Range Setup, 12-18 Schilling Test Measurement Analysis,
Numeric Keypad, 3-5, 9-14, 9-20, 9-27,
11-11
9-34, 10-24, 11-6, 11-17, 11-30 Schilling Test Measurement Entry, 11-4
Patient Measurement, 12-49 Schilling Test Report, 14-36
Schilling Test Search, 14-33
Schilling Tests Search After Search, 14-

34
Search BioAssay, 14-61

i-12 INDEX October 15

CAPINTEC, INC. CAPTUS® 700t

Search BioAssay with Highlighted Test, Thyroid Uptake – View Protocol, 12-24,
14-66 14-57

Search RBC Survival Tests – All Thyroid Uptake Search with Highlighted
Patients, 14-47 Patient, 14-55

Search Thyroid Uptake Tests, 14-52 Thyroid Uptake Test Report, 14-56
Search Thyroid Uptake Tests – All Touchscreen Calibration, 5-20
USB PC Driver Select, 5-17
Patients, 14-53 User Nuclides Setup, 6-24
Search Wipes after Search, 14-28 User Nuclides Setup with Nuclide, 6-28
Search Wipes with Highlighted Wipe, User Nuclides Setup with Nuclide

14-30 Selected, 6-29
Select Staff List, 13-21, 14-62 Utility, 7-2, 15-2
Select Staff, Member Highlighted, 13-
Utility Screen with Diagnostics System
22, 14-63 Test PASS, 7-3
Select Thyroid Uptake Protocol, 12-20
Setup, 4-9, 5-4, 5-18, 6-2, 10-3, 12-5, Utility with Login Button, 4-23
Viem Patient Test Results, 12-56
13-3 Well Measurements – Drilled Probe, 10-
Setup – after Day Month Year Selected,
5
5-6 Well Measurements – Probe/Well, 10-5
Setup – after Year Month Day Selected, Well Wipes Setup, 10-6
Wipe Criteria Selection, 14-27
5-6 Wipe General Measurement, 10-33
Setup BioAssay ROI, 13-8 Wipe General Measurement Report, 10-
Setup RBC Survival Normal Range, 11-
38
43 Wipe General Measurement Results,
Setup Staff, 4-10
Setup Staff – root, 4-13 10-37
Setup Staff – root selected, 4-14 Wipe General Measurement Set
Setup Staff with Name Highlighted –
Nuclide, 10-34
root, 4-20 Wipe General Measurement Set ROI,
Setup Thyroid Uptake Protocol, 12-8
Setup Thyroid Uptake Protocol with 10-36
Wipe Measurement, 10-29
Highlighted Protocol, 12-15 Wipe Measurement Results, 10-30
Setup Wipe Locations, 10-15 Wipe Report, 14-31
Spectrum, 11-12, 11-26, 11-38, 12-58, Wipe Test Spectrum, 10-31
Wipes Search, 14-26
14-60 Screen Adjustments, 5-18
Spectrum for Efficiency, 6-21 Brightness, 5-19
Startup, 2-5, 4-6 Calibration, 5-20
System Test Measurement, 9-19 Sleep Brightness, 5-19
System Test Measurement Results, 9- Sleep Timeout, 5-18
SCREEN CALIB button, 5-20
21 Screen Calibration, 5-20
System Test Result, 14-12 SEALED SOURCE button, 14-28
System Test Results, 9-22 Sealed Sources
System Test Search with Highlighted Settings, 10-13
SEARCH button, 11-53, 12-34, 14-6, 14-
Test, 14-11 10, 14-17, 14-22, 14-28, 14-34, 14-39,
System Test Spectrum, 9-23, 14-15 14-42, 14-47, 14-48, 14-53, 14-54, 14-
System Tests Search after Search, 14- 64
Security Roles, 4-8
10
Test Source Setup, 6-6, 6-10
Thyroid Uptake – View Measurements

Results, 12-57, 14-59

October 15 INDEX i-13

CAPINTEC, INC. CAPTUS® 700t

Admin, 4-8 Schilling Test, 11-8
Guest, 4-8 STOP button, 6-21, 9-14, 9-20, 9-27, 9-36,

root, 4-8 10-25, 10-29, 10-37, 11-6, 11-8, 11-9,
User, 4-8 11-17, 11-20, 11-21, 11-22, 11-30, 11-
32, 11-33, 11-34, 11-35, 13-14
Security Status, 4-8 Summary Report
Disable, 4-8 Auto Calibration, 14-7
Enhanced, 4-8 BioAssay, 14-65
Chi Square Test, 14-23
setting, 4-16 MDA Test, 14-18
Traditional, 4-8 Plasma Test, 14-39
SELECT button, 13-21, 14-63 RBC Test, 14-43
Select Nuclide Schilling Test, 14-35
MDA Test, 9-29 System Test, 14-11
Wipe Test, 14-29
Select Protocol, 12-20 Symbol Definitions, 1-1
SELECT PROTOCOL button, 12-21 System Hardware
Selecting Wipe Locations, 10-27 Detector Inputs, 2-10
Servicing, 16-5 Isolation Transformer, 2-9
MCA, 2-10
Fuse, 16-8 Printer, 2-10
Set Nuclide/ROI Probe Detector, 2-11
Software, 2-10
General Measurement, 10-34 Stand, 2-9
Well Detector, 2-11
Setup System Initialization, 5-1
General Operational, 4-7 System Power Requirements, 2-12
System Setup, 4-1
SETUP BIOASSAY ROI button, 13-8 System Test, 8-1, 9-18
SETUP button, 3-4, 4-9, 4-25, 6-2, 9-18, Count Time, 9-19, 9-27
Detailed Report, 14-11
12-5, 13-3 Inactivate, 14-12
SETUP LOCATION button, 10-15 Measurement, 9-20
Shipping, 16-19 Report, 14-8
SINGLE ARROW button, 9-15, 9-24, 9-39, Results, 9-22
Summary Report, 14-11
10-25, 10-31, 10-37, 11-6, 11-8, 11-9, SYSTEM TEST AS PROBE button, 9-18
11-13, 11-17, 11-20, 11-21, 11-22, 11- SYSTEM TEST AS WELL button, 9-18
SYSTEM TEST button, 9-18
26, 11-30, 11-33, 11-34, 11-35, 11-39, SYSTEM TEST REPORT button, 14-8
11-62, 12-58, 14-15, 14-20, 14-25, 14-
32, 14-37, 14-41, 14-45, 14-51, 14-60, T
14-68 Table
SKIP ALL WIPES button, 10-28, 10-30
SKIP PRE-DOSE button, 12-38 Chi Square Typical Values, 9-32, 9-40
SKIP WIPE button, 10-28, 10-30 Default Trigger Levels, 10-7
Sleep Brightness, 5-19 Disposal Information, 16-4
Sleep Timeout, 5-18 Dosage Information, 12-29
Speaker Volume, 5-21 Dose Measurement, 12-11
Symbol Definitions, 1-1
Specifications Trigger Levels Limits, 10-7

Technical, 2-9
SPECTRUM button, 9-23, 9-32, 10-31, 14-

14, 14-20, 14-32
spillover, 13-17
Spring-Arm Inspection, 16-6
Staff, 13-19
STAFF button, 4-9, 4-25
standard deviations, 9-29

Standard Dilution Factor
Plasma Test, 11-18

i-14 INDEX October 15

CAPINTEC, INC. CAPTUS® 700t

Technical Description, 2-8 Thyroid Uptake Module, 12-1
Detector, 2-8 THYROID UPTAKE NORMAL VALUES
Multichannel Analyzer, 2-8
button, 12-17
Technical Specifications, 2-9 THYROID UPTAKE REPORT button, 14-
System Hardware, 2-9
System Power Requirements, 2-12 52
Thyroid Uptake Test
Test
Acceptance, 8-1 Detailed Report, 14-55
Chi Square, 9-32 Time
MDA, 9-24
Plasma, 11-14 entering, 5-1
Quality Assurance, 8-1 Traditional Security Status, 4-8
RBC, 11-28 Training
System, 8-1, 9-18
Operator, 2-2
TEST button, 5-21 Trigger Levels, 10-7
Test Source, 4-7
Background, 10-8
Calibrated Activity Field, 6-9 BioAssay, 13-7
Calibrated On Field, 6-8 Default, 10-7
S/N Field, 6-7 Limits, 10-7
TEST SOURCE button, 6-6 Packages, 10-14
Test Source Data, 6-6 Sealed Source, 10-13
Testing Unrestricted Area, 10-12
Acceptance, 4-7 Wipe Location, 10-18
Contamination, 8-2 Work Area, 10-10
Tests, 9-1 Troubleshooting, 16-17
Thyroid Uptake, 2-3
Dosage Activity, 12-30 U
Dosage Calibration Date, 12-31 UNRESTRICTED AREA button, 14-28
Dosage Information, 12-29 Unrestricted Areas
Dosage Lot Number, 12-32
Dosage Number/Factor, 12-32 Settings, 10-12
Making Measurements, 12-36 UP ARROW (▲) button, 3-7, 6-13, 9-29,
Normal Values, 12-17
Patient Date of Birth (DOB), 12-27 10-11, 10-19, 10-20, 10-21, 10-27, 10-
Patient First Name, 12-26 35, 11-52, 12-3, 12-15, 12-16, 12-20,
Patient ID, 12-27 12-33, 13-21, 14-7, 14-10, 14-18, 14-23,
Patient Information, 12-26 14-29, 14-35, 14-39, 14-43, 14-47, 14-
Patient Last Name, 12-27 53, 14-63, 14-65, 15-4
Patient Physician, 12-28 Urine Aliquot Volume
Patient Reports, 12-55 Schilling Test, 11-7
Patient Sex, 12-28 Urine samples, counting, 10-32
Patient Technologist, 12-29 Urine Test, 2-3
Protocols, 12-9 Schilling Test, 2-3
Quick Step Guide, 12-4 Urine Volume
Reactivate a Patient, 14-56 Schilling Test, 11-7
Report, 14-52 USB PC driver, 5-17
Results, 12-55 User
Select Protocol, 12-20 add, 4-16
THYROID UPTAKE button, 3-4, 12-2, 12- edit, 4-20
7 inactivate, 4-22
reactivate, 4-22
User login, 4-8
User Nuclide, 6-24
Add, 6-24

October 15 INDEX i-15

CAPINTEC, INC. CAPTUS® 700t

Delete, 6-30 Count Time, 10-18
Edit, 6-29 Deleting, 10-21
Element Field, 6-26 Editing, 10-20
Energy1(keV) Field, 6-26 Name, 10-17
Energy2(keV) Field, 6-27 Nuclides, 10-18
Energy3(keV) Field, 6-27 Saving, 10-19
Halflife Field, 6-26 Selecting, 10-27
Nuclide Field, 6-25 Setup, 10-14
Probe Efficiency(%) Field, 6-27 Trigger Level, 10-18
Well Efficiency(%) Field, 6-27 Wipe Type, 10-16
USER NUCLIDES button, 6-24 WIPE REPORT button, 14-26
Users Wipe Test, 2-3, 10-1
changing, 4-23 Count Time, 10-28
UTILITY button, 3-4, 4-23, 4-26, 7-1, 15-1 Detailed Report, 14-30
Full Spectrum Efficiency, 10-2
V Inactivate, 14-31
VIEW button, 12-24, 14-7, 14-11, 14-19, Report, 14-26
Results, 10-30
14-23, 14-30, 14-35, 14-40, 14-44, 14- Setup, 10-3
49, 14-54, 14-55, 14-66 Setup Location, 10-14
VIEW NORMAL button, 11-60, 14-50 Summary Report, 14-29
VIEW PROTOCOL button, 14-57 WIPE TESTS button, 10-4
Voltage Wipe Type
High, 1-5, 1-6 selecting, 10-16
Wipes
W Measuring, 10-26, 10-28
warm-up period, 2-12 Work Area
WELL button, 6-5, 9-5, 14-5, 14-9, 14-17, Settings, 10-10
WORK AREA button, 14-28
14-21
Well Efficiency(%) Field, 6-27 Y
WILDCARD (%) button, 11-52, 11-53, 12- YES button, 14-14, 14-20, 14-25, 14-32,

33, 12-34, 14-47, 14-48, 14-53, 14-54 14-37, 14-41, 14-45, 14-50, 14-56, 14-
Wipe categories, 10-1 68
Wipe Full Spectrum Efficiency, 6-11, 10-2
Wipe Location

Add, 10-15

i-16 INDEX October 15

CAPINTEC, INC. CAPTUS® 700t

NEW PRODUCT WARRANTY

Conditions and Limitations

CAPINTEC warrants our products to be free from defects in material and
workmanship for a period of 24 months after delivery to the original buyer
(unless indicated otherwise). Our obligation under this warranty is
limited to servicing or adjusting products returned to our factory for that
purpose promptly upon any claim under this warranty, provided our
examination discloses to our satisfaction that the affected parts were
originally defective and have not been subjected to misuse, abuse,
mishandling or improper operation. This warranty extends to every part
of the product except batteries, fuses, ink, magnetic storage media,
toner, transistors, tubes or any other normally consumable item. In no
event shall we liable for transportation, installation, adjustment or any
other expenses which may arise in connection with such products or
their servicing or adjustment.

This warranty is expressly in lieu of any other express or implied
warranties, and we make no warranty that the products sold herein are
merchantable or are suitable for any particular purpose. The benefits of
this warranty shall extend only to the buyer and to none other. We shall
have no liability of any nature arising out of the use or application of the
product in conformity with this warranty. If the product shall fail to
perform in conformity with the warranty made herein, we shall be liable
solely for the repair and replacement of the product as provided
hereinabove, and shall have no other liability in respect of such failure or
performance, or any consequences therefrom, including, without
limitation, business impairment or loss, personal injury or property
damage.

No agent, employee, or representative of ours has any authority to bind
us to any representation or warranty concerning the product sold herein,
and unless a representation or warranty made by an agent, employee or
representative is specifically included herein, it shall not be enforceable
by the buyer. No waiver, alteration or modification of the foregoing
conditions shall be valid, unless made in writing and signed by an
executive officer of our corporation.

CAPINTEC, INC. CAPTUS® 700t

This page intentionally left blank.