TRANS PAINT Company Manual

PRODUCT 2 PACKAGING APPLICATION TYPE
Sno-Cote Emulsion
Sno-Cote Undercoat Interior Finish Economical matt
finish

(water-based)

Interior Economical
Undercoat undercoat
(water-based)

Sno-Cote Xtra Weather Exterior/ Low sheen finish
Interior Finish (water-based)

Sno-Cote Xglo Interior Finish Mid-sheen finish
(water-based)

TOP Emulsion Sealer Exterior/ Economical
Interior Sealer sealer

(water-based)

v White Only; P via Colour Waves Tinting System only

SUBSTRATE STANDARD PACK SIZES SIRIM PRODUCT VIA COLOUR
COLOURS CERTIFICATION WAVES (CW)
Concrete/ 1L P
Masonry Sno-Cote 7L Sno-Cote Series;
Emulsion
Colour Chart; 18L v Nil 100 colours;
48 colours Two bases;

1L, 7L, 18L

Concrete/ White 7L Nil N/A
Masonry 18L

Sno-Cote Xtra 1L P Sno-Cote Series;
Weather Colour
Concrete/ Chart; 20 colours 5L Nil 100 colours;
Masonry 18L v Two bases;

1L, 5L, 18L

1L P Sno-Cote Series;
5L
Concrete/ White 18L Nil 100 colours;
Masonry Two bases;

1L, 5L, 18L

Concrete/ White 18L Nil N/A
Masonry

PRODUCT 2 PACKAGING APPLICATION TYPE
TOP Cat Kilat
Interior Finish Economical gloss
finish

(solvent-based)

TOP Cat Kilat Undercoat Interior Economical gloss
Undercoat undercoat

(solvent-based)

TOP Road Line Road Marking Economical semi-
TOP Aluminium gloss finish
TOP Greygreen Oxide
(solvent-based)

Industrial Finish Economical
Aluminium finish
(solvent-based)

Industrial Primer Economical anti-
corrosive primer
(solvent-based)

SUBSTRATE STANDARD PACK SIZES SIRIM PRODUCT VIA COLOUR
COLOURS CERTIFICATION WAVES (CW)

Wooden/ TOP Cat Kilat 250mL Nil N/A
Ferrous/ Steel/ Colour Chart; 1L
5L
Iron 40 colours

Wooden/ 1L

Ferrous/ Steel/ White 5L Nil N/A

Iron 18L

Asphalt White, Yellow, 5L Nil N/A
Black

Ferrous/ Steel/ Aluminium 1L Nil N/A
Iron 5L
18L

Ferrous/ Steel/ Greygreen 1L Nil N/A
Iron 5L
18L

PRODUCT 2 PACKAGING APPLICATION TYPE
TOP Red Oxide
Industrial Primer Economical anti-
corrosive primer
(solvent-based)

TOP Black oxide Industrial Primer Economical anti-
corrosive primer
TOP Truck & Tractor (solvent-based)

TOP Solvent Sealer Automotive High gloss
Refinish automotive
TOP Marine & Industrial
Primer refinish
(solvent-based)
TOP Marine & Industrial
Finish Exterior/ Economical
Interior Sealer acrylic sealer
(solvent-based)

Marine/ Marine/
Industrial Primer Industrial anti-
corrosive primer
(solvent-based)

Marine/ Marine/
Industrial Finish Industrial high

gloss finish
(solvent-based)

SUBSTRATE STANDARD PACK SIZES SIRIM PRODUCT VIA COLOUR
COLOURS CERTIFICATION WAVES (CW)

Ferrous/ Steel/ Red 1L
Iron 5L Nil N/A
18L

Ferrous/ Steel/ Black 1L Nil N/A
Iron 5L
18L

Ferrous/ Steel/ Yellow 5L Nil N/A
Iron Black

Concrete/ White 5L Nil N/A
Masonry 18L

Ferrous/ Steel/ White 5L Nil N/A
Iron 5L Nil N/A

Ferrous/ Steel/ White
Iron Black
Grey
Red Oxide

PRODUCT 3 PACKAGING APPLICATION TYPE
Econlite Emulsion
Interior Super-
Econ White Emulsion economical extra
HIPER PRODUCT
Hiper Wood Marker matt finish
(water-based)
Hiper Cat Kayu
Hiper Filler Interior Super-
Hiper MC 7 (AQ) economical extra

matt finish
(water-based)

PACKAGING APPLICATION TYPE

Exterior Sawn timber
Interior marking paint
(solvent-based)

Exterior Timber marking T
Interior paint

Interior (solvent-based)

Interior Putty filler
(powder form)

Timber truss
coating

(water-based)

SUBSTRATE STANDARD PACK SIZES SIRIM PRODUCT VIA COLOUR
COLOURS CERTIFICATION WAVES (CW)

Concrete/ Econlite Colour 7L Nil N/A
Masonry Chart; 48 colours

Concrete/ White 18L Nil N/A
Masonry

SUBSTRATE STANDARD PACK SIZES SIRIM PRODUCT VIA COLOUR
Sawn timber COLOURS CERTIFICATION WAVES (CW)

Timber/ Wooden White 4 Gallon Nil N/A
Concrete/ Black
Masonry Red 1.75L Nil N/A
Yellow Nil N/A
Blue 1lb Nil N/A
Green 4lb
White
Black 1 Gallon
Red 2 Gallon
Yellow
Blue
Green

White

Timber truss Blackish

Recommended Painting System (Prem

USE TYPE OF PRIMING/ UNDERCOATING
Exterior SUBSTRATE
NU-COTE WALL SEALER, or
Masonry Walls PLUSS AP SEALER for powdery surface

Interior Wooden Doors & PLUSS ALUMINIUM WOOD PRIMER, a
Windows PLUSS QD UNDERCOAT
No primer/ undercoat required for NU
Metallic PLUSS INDUSTRIAL ZINC PHOSPHATE
PLUSS QD UNDERCOAT for uneven or
Roofing No primer/ undercoat required for NU
Masonry Walls & NU-COTE WALL SEALER, or
Ceilings PLUSS AP SEALER for powdery surface

Wooden Doors & PLUSS ALUMINIUM WOOD PRIMER, a
Windows PLUSS QD UNDERCOAT
No primer required for
Metallic NU-COTE TIMBER and NU-COTE UVW
PLUSS INDUSTRIAL ZINC PHOSPHATE
PLUSS QD UNDERCOAT for uneven or

mium)

FINISHING

1 coat NU-COTE WEATHER 2 coats
es
2 coats
and 1 coat NU-COTE GLOSS, or 2 coats
1 coat 2 coats
U-COTE UVWOOD NU-COTE UVWOOD 3 coats
E PRIMER, and 1 coat NU-COTE GLOSS 2 coats
r stained surfaces 1 coat
U-COTE UVROOF NU-COTE UVROOF 2 coats
1 coat NU-COTE OCEANGLO, or 3 coats
es NU-COTE RICH, or 2 coats
1 coat NU-COTE EMULSION
and 1 coat NU-COTE GLOSS

WOOD 1 coat NU-COTE TIMBER, or
E PRIMER, and 1 coat NU-COTE UVWOOD
r stained surfaces NU-COTE GLOSS

Recommended Painting System (Econ

USE TYPE OF PRIMING/ UNDERCOATING
Exterior SUBSTRATE
TOP EMULSION SEALER or
Masonry Walls TOP SOLVENT SEALER for powdery su
TOP CAT KILAT UNDERCOAT
Wooden Doors &
Windows TOP GREYGREEN OXIDE, and TOP CA
UNDERCOAT
Metallic for uneven or stained surfaces
TOP EMULSION SEALER, or SNO-COT
Interior Masonry Walls TOP SOLVENT SEALER for powdery su

Ceilings ECON WHITE EMULSION

Wooden Doors & TOP CAT KILAT UNDERCOAT
Windows
TOP GREYGREEN OXIDE, and TOP CA
Metallic UNDERCOAT
for uneven or stained surfaces

nomical)

FINISHING 2 coats

1 coat SNO-COTE XTRA WEATHER

urfaces

1 coat TOP CAT KILAT 2 coats

AT KILAT 1 coat TOP CAT KILAT 2 coats
1 coat 2 coats
1 coat
TE UNDERCOAT or 1 coat SNO-COTE EMULSION, or

urfaces SNO-COTE XGLO

1 coat ECON WHITE EMULSION

1 coat TOP CAT KILAT 2 coats

AT KILAT 1 coat TOP CAT KILAT 2 coats
1 coat

Surface Preparation NEW UNPAINTED SURF
 Ensure surfac
TYPE OF SUBSTRATE  Apply approp
CONCRETE WALLS/CEILINGS (MASONRY)

METAL/FERROUS SUBSTRATE  Remove rust
WOODEN SUBSTRATE or mechanica

 Ensure surfac
and other co

 Ensure surfac
grease and o

 Sanding surfa
for better ad

Touchup procedures Clean, degrease and dry affected areas bef
CONCRETE/ MASONRY: remove previous paint film that is loose if
allow to cure. Then paint with the recomm
WOODEN SURFACE: Remove loose adhering paint film. Clean a
adhesion and appearance. Cracks can be fi
METAL SURFACE: as described above.
Remove loose adhering paint film. Clean a
Cracks can be filled with any polyester put

FACE PREVIOUS PAINTED SURFACE
ce is clean and dry  Remove lose paint film by hard
priate sealer scraping/ high pressure water jet
 Treat fungi, algae or mould with
t or millscales by manual Pluss Biocidal Wash
al cleaning  Ensure dry off before painting
ce free from oil, grease
ontaminant  Remove loosely adhering paint
ce is free from oil,  Remove debris, oil, grease or other
other contaminants
ace with abrasive paper contaminants before painting
dhesion and appearance  Use suitable primer
 Remove loose adhering paint
 Ensure surface is clean and dry
 Use suitable primer

fore touchup. Wash off any algae or fungi with PLUSS BIOCIDAL WASH and
necessary. Cracks can be filled with suitable water proofing material and
mended coats of paint as described above.
and dry the affected surface; sand with abrasive paper if necessary for better
illed with any wood putty. Then paint with the recommended coats of paint

and wipe surface to remove debris, oil/grease or other contaminants.
tty. Then paint with the recommended coats of paint as described above.

Propose Painting Scheme

System Coat Product Coveragex/Coat
No. m2/liter/coat ft2/liter/coat
External Wall
(NC Weather) 1st NU-COTE WALL SEALER 8 86
2nd
Internal Wall 3rd NU-COTE WEATHER 10 108
(NC Emulsion) 1st
2nd NU-COTE WEATHER 10 108
Internal Wall 3rd
(NC Rich) 1st NU-COTE WALL SEALER 8 86
2nd
Internal Wall 3rd NU-COTE EMULSION 10 108
(NC OceanGlo) 1st
2nd NU-COTE EMULSION 10 108
External Wall 3rd
(SC Xtra Weather) 1 st NU-COTE WALL SEALER 8 86
2 nd
Internal Wall 3 rd NU-COTE RICH 10 108
(SC Xglo) 1 st
2 nd NU-COTE RICH 10 108
Internal Wall 3 rd
(SC Emulsion) 1 st SNO-COTE UNDERCOAT 8 86
2 nd
3 rd NU-COTE OCEANGLO 10 108

NU-COTE OCEANGLO 10 108

TOP EMULSION SEALER 8 86
SNO-COTE XTRA WEATHER WHITE 9102 w 10 108
SNO-COTE XTRA WEATHER WHITE 9102 w 10 108

SNO-COTE UNDERCOAT 8 86

SNO-COTE XGLO 10 108

SNO-COTE XGLO 10 108

SNO-COTE UNDERCOAT 8 86

SNO-COTE EMULSION 10 108

SNO-COTE EMULSION 10 108

w Price varies with colour series
x Estimated practical coverage
y Based on Price List dated 1 Jan 2016 (largest pack size & White 9102); Users advised to check fo
z Estimated rate in Kuching region; Figures provided in good faith for guidance only

Disclamer: Every care has been taken to ensure the accuracy of the information contained in this
warrant it, it is recommended that the data are checked to ensure their suitability for the use env

Paint Costy Paint System Costy Workmanship Total Cost
Costz RM/ft2
RM/m2 RM/ft2 RM/m3 RM/ft3 RM/ft2
1.95 0.18
2.57 0.24 7.09 0.66 0.50 1.16
2.57 0.24
1.95 0.18 5.00 0.46 0.50 0.96
1.52 0.14
1.52 0.14 7.05 0.65 0.50 1.15
1.95 0.18
2.55 0.24 5.84 0.54 0.50 1.04
2.55 0.24
0.86 0.08 5.28 0.49 0.50 0.99
2.49 0.23
2.49 0.23 4.41 0.41 0.50 0.91
1.49 0.14
1.90 0.18 2.23 0.21 0.50 0.71
1.90 0.18
0.86 0.08
1.78 0.16
1.78 0.16
0.86 0.08
0.68 0.06
0.68 0.06

or latest price revision with any TRANS PAINT authorised dealers

s data sheet, but no liability can be accepted arising from its use. Where the conditions of use
visaged.

Estimated Material Cost/ Area (List Price)

Product Size (L) List Pricex (RM) m

NU-COTE WEATHER* 5 139.39 1

NU-COTE WEATHER* 20 513.57 1

NU-COTE OCEANGLO* 5 135.68 1

NU-COTE OCEANGLO* 20 498.20 1

NU-COTE RICH* 5 138.33 1

NU-COTE RICH* 20 509.86 1

NU-COTE EMULSION* 5 87.13 1

NU-COTE EMULSION* 20 304.22 1

NU-COTE GLOSS* 5 138.86 1

NU-COTE TIMBER 5 132.08 2

NU-COTE WALL SEALER 5 84.91 8

NU-COTE WALL SEALER 20 312.70 8

PLUSS AP SEALER 5 142.78 8

PLUSS QD UNDERCOAT 5 88.30 1

PLUSS INDUSTRIAL ZINC PHOSPHATE PRIMER 5 134.30 1

PLUSS ALUMINIUM WOOD PRIMER 5 98.58 1

NU-COTE UVROOF # 20 480.00 5

NU-COTE UVWOOD # 20 440.00 1

SNO-COTE XTRA WEATHER* 5 104.41 1

SNO-COTE XTRA WEATHER* 18 341.32 1

SNO-COTE XGLO* 5 100.70 1

SNO-COTE XGLO* 18 320.12 1

SNO-COTE EMULSION* 7 55.54 1

SNO-COTE EMULSION* 18 123.28 1

TOP EMULSION SEALER 18 214.12 8

SNO-COTE UNDERCOAT 18 123.28 8

TOP CAT KILAT 5 99.64 1

TOP CAT KILAT UNDERCOAT 5 53.00 1

TOP CAT KILAT UNDERCOAT 18 175.43 1

TOP SOLVENT SEALER 18 400.25 8

TOP GREYGREEN OXIDE 5 88.30 1

TOP GREYGREEN OXIDE 18 312.70 1

* Based on standard White 9102; # Based on average colour
x Based on Price List dated 1 Jan 2016; Users advised to check for latest price revision with any
y Estimated practical coverage
Disclaimer: Every care has been taken to ensure the accuracy of the information contained in t

use warrant it, it is recommended that the data are checked to ensure their suitability for the u

Coveragey/Coat Estimated Material Cost*/Area

m2/L ft2/L RM/m2 RM/ft2

1 Coat 2 Coats 1 Coat 2 Coats

10 108 5.58 0.52
10 108
10 108 5.14 0.48
10 108
10 108 5.43 0.50
10 108
10 108 4.98 0.46
10 108
15 161 5.53 0.51
20 215
8 86 5.10 0.47
8 86
8 86 3.49 0.32
15 161
12 129 3.04 0.28
12 129
5 54 3.70 0.34
10 108
10 108 2.64 0.25
10 108
10 108 2.12 0.20
10 108
10 108 1.95 0.18
10 108
8 86 3.57 0.33
8 86
1.18 0.11
15 161
15 161 2.24 0.21
15 161
8 86 1.64 0.15
12 129
12 129 9.60 0.89

4.40 0.41

4.18 0.39

3.79 0.35

4.03 0.37

3.56 0.33

1.59 0.15

1.37 0.13

1.49 0.14

0.86 0.08

2.66 0.25

0.71 0.07

0.65 0.06

2.78 0.26

1.47 0.14

1.45 0.13

y TRANS PAINT authorised dealers (price inclusive of 6% GST)

this data sheet, but no liability can be accepted arising from its use. Where the conditions of
use envisaged.

PRE-WARRANTY NOTE

FIVE-YEAR LIMITED PRODUCT WARRANTY

NU-COTE WEATHER

TO WHOM IT MAY CONCERN

Promise of Quality

TRANS PAINT Nu-Cote Weather is guaranteed to provide film integrity and adhesion for the expected
life of the paint system (Five-Year). Should the paint is proved to fail without being affected or
jeopardized by poor workmanship or by any underlying, external or surrounding factors, TRANS
PAINT shall provide replacement paint to rectify the affected area after detailed investigation and
upon presentation of the authorized limited product warranty.

We would like to inform you that the above warranty will only be issued subject to the following
conditions being met:

1. Paint System

Exterior No. of Coats Maximum Minimum Dry Film Thickness
Dilution (DFT in microns)

Nu-Cote Wall Sealer/ 1 5% 20
Pluss AP Sealer

Nu-Cote Weather 2 5% 60 (total)

DFT is measured from the highest point of the substrate to the surface of the paint.

2. Workmanship (Applicator/ Painter)

Only TRANS PAINT authorized/ registered applicator or painter shall be used in order for the
warranty to be issued. To register, the applicator or painter must attend a one-time warranty
briefing session at TRANS PAINT Factory.

3. Surface Preparation

New Unpainted Surface Previous Painted Surface

 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with TRANS PAINT
Pluss Biocidal Wash

 Ensure dry off before painting

a. In general cementitious surfaces may be highly alkaline especially when new.
b. The moisture and alkalinity in fresh masonry may combine to attack many types of

coatings by a process called hydrolysis which subsequently leads to film deterioration
(chalking, colour fading, loss of adhesion etc.).
c. Depending on the environment, the substrate needs at least 30 to 60 days to cure or
until a surface pH of 9 is realized.

PRE-WARRANTY NOTE

d. Cracks must be patched using appropriate compound such as mortar, plaster, caulk
etc. paying attention to the suitability of the materials in your application (exterior or
interior).

e. Joints and patches must be checked for its pH level as well before painting, with the
same treatment as the cement substrate.

f. Moisture content in the substrate can be checked with a moisture detector. A typical
unit would have simple indicator showing the levels of dampness at which painting is
permissible or otherwise.

g. Efflorescence, crusty white salt deposits leached from masonry as moisture passes
through, is common in many masonry surfaces. It must be removed thoroughly prior
to painting and the cause must be determined and corrected to avoid reoccurrence
on painted surfaces.

4. Material Usage

We reserve the right to know the source and the quantity of paint material purchased for the
project. The amount should be consistent with our assessed paint consumption and in the
event that the variance is significantly lower than our estimates, we reserve the right to
withhold the issuance of the warranty.

5. Site Inspection

As detailed in 3, our representative may/ shall perform random site inspections in the process
of surface preparation and painting of the project. We reserve the right to sample the wet
paint and remove paint film for testing. Any non-conformance against our recommendation
and conditions will render the warranty to be unsuccessful. Please take note also that we
expect only our approved paint containers to be allowed at site and the presence of other
brands’ containers will be viewed with great suspicion and may jeopardise our warranty.

6. Paint Warranty

Warranty against paint defects on products shall be provided for a period of five (5) years
commencing from the date of practical completion of the project. Other information,
exclusions, terms, conditions and claims are detailed in the warranty form.

Attached please find a copy of the sample warranty form and painter registration form for your
reference and understanding.

WARRANTY FORM

FIVE-YEAR LIMITED PRODUCT WARRANTY

NU-COTE WEATHER

A. PROJECT INFORMATION -
Trans-Ocean Coatings & Chemicals Sdn Bhd (hereinafter called ‘TRANS PAINT’) warrants the painting of -
Project/ Premise Name

Location

Owner -

Contractor -

Applicator/ Painter -

TRANS PAINT  New Construction  Repainting -
Authorized Dealer -(tick)

Nature of Painting Job -

Painting Commenced on

Painting Completed on -

Effective Warranty
Period

B. CONDITIONS & LIMITATIONS

1. TRANS PAINT shall provide a FIVE (5) Year Limited Warranty to the above-mentioned project owner commencing
from the actual completion date(s) as specified against the following paint defects caused by weathering in the
natural elements.

PEELING Paint films peel away from building surface other than that caused by the presence of
moisture or efflorescence from the substrate.

CRACKING Cracking in the paint film other than that caused by plastering or substrate cracks.

EXCESSIVE Paintwork loses its colour or fades excessively in patches and uneven discoloration appears
FADING other than that caused by the presence of moisture or high alkalinity from the substrate.
However, gradual fading is a normal condition since all exterior paints exhibit fading when
exposed to weather.

EXCESSIVE Paint films chalk more than normal for emulsion paint and has adversely affected the
CHALKING appearance on the paintwork.

FUNGUS & Growth of microorganisms on the paint surface which results in the marring of the appearance
ALGAE of the paintwork. However, fungus and algae may form on surfaces over time because of
GROWTH moisture and periodical removal shall be required and considered part of routine Owner
maintenance and is not covered by the Warranty.

Note: Contractor/ Applicator to fill/ sign in the relevant information in the space marked ‘X’ and return to TRANS PAINT factory at Lot 1393,
Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching, Sarawak or fax to 082-339189 before the Product Warranty can be issued.

WARRANTY FORM

2. The warranty does not cover:
a. Products that have not been paid in full.
b. Horizontal surfaces and plywood siding.
c. Minor imperfection in paint that do not affect the product’s integrity or obscure appearance or minor
variations in colour.

3. The warranty excludes defects arising from the followings:
a. Structural faults or movements, Acts of God or job damage or excessive accumulation of atmospheric dirt,
stains or other factors beyond the control of TRANS PAINT.
b. Attack from chemical agents, fumes, liquids or solids other than direct rain falling on to the product under
warranty.
c. Application subject to severe industrial or unusual environments at any time unless specifically stated
otherwise.
d. Damage of the painted surface resulting from vandalism or any intentional and unintentional heavy impact.
e. Defects following alteration or extension work onto the affected areas of building without the prior consent
or agreement from TRANS PAINT.

4. The warranty is subject to the following terms and conditions:
a. The product is used strictly in accordance with TRANS PAINT application recommendations. The contractor/
applicator is responsible for ensuring a sound surface for painting.
b. The paint being applied must be unadulterated. TRANS PAINT has the right to sample the wet paint and
remove paint film for testing.
c. The surface being applied is not affected by water leakage or in contact with soil, ashes, fertilizers, or other
moisture retaining substances. TRANS PAINT has the right to pre-inspect the project site before painting.
d. TRANS PAINT extends this warranty solely to the owner and is not applicable to any third party.
e. The warranty shall be limited to the extent of TRANS PAINT making good the affected areas only.
f. The warranty is void if any other paint or film is applied on the warranted paint surface.
g. In the case of extended painting period in a single project, the Warranty shall commence from the earliest
date of painting job carried out in that project.
h. Periodical cleaning of the exterior surface is deemed necessary in maintaining the aesthetic and durability
of the paint system. An interval of twelve (12) months is recommended between each cleaning, depending
on environmental conditions. The maintenance program is not covered by the Warranty.
i. TRANS PAINT shall not be liable or responsible for any loss/ consequential loss arising from any paint
defects if any of the above-mentioned terms and conditions is breeched.

5. Followings is the procedure for claims:
a. All claims shall be made in writing to TRANS PAINT Coatings & Chemicals Sdn Bhd of 1393, Jalan Meranti,
Bintawa Industrial Estate, 93450 Kuching, Sarawak.
b. An investigation technical team shall conduct the nature of claim within ONE (1) week from receipt of the
formal claims.
c. TRANS PAINT shall bear the cost of paint materials only if the investigation concludes the defects are within
the scope of warranty.
d. Where the repairs affect more than 50% of a wall or ceiling product area, TRANS PAINT shall provide the
paint materials for the entire wall, ceiling or product surface with the original paint.
e. Due to fading and normal weathering, a perfect match cannot be achieved and a perfect match is not
covered by the Warranty.
f. The warranty on any replacement product will extend for the balance of the original warranty period.
g. TRANS PAINT shall not be liable or responsible for the claim if the investigation concludes that the defects
to be out of the scope of the warranty as provided in clause 2.

Contractor/ Applicator’s acknowledgement Signature and Stamp
Date
I/We have understood and hereby accept the
conditions and limitations stipulated above in
order for the warranty to be effective.

-

Note: Contractor/ Applicator to fill/ sign in the relevant information in the space marked ‘X’ and return to TRANS PAINT factory at Lot 1393,
Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching, Sarawak or fax to 082-339189 before the Product Warranty can be issued.

PAINTER REGISTRATION FORM

Company Name

Company Registration No.

Business Address

Telephone No.

Fax No.

Mobile Phone No.

No. of full-time workers

TRANS PAINT products 1.
purchased from 2.
3.
(Authorized Dealer’s name)

Project References (if any) 1.

2.

3.

4.

5.

I hereby declare that the information contained in this application is complete and correct to
the best of my knowledge and belief.

Signature

Company Chop Name
Designation
Date

Note: Contractor/ Applicator to complete this form and return to Trans Paint factory at Lot 1393, Jalan
Meranti, Bintawa Industrial Estate, 93450 Kuching, Sarawak or fax to 082-339189 before the Product
Warranty can be issued.

.

Product
Technical Data Sheet

(TDS)

TRANS PAINT Technical Data Sheet (TDS)

COLOUR WAVES WASHING LIQUID
(MONOPROPYLENE GLYCOL)

A clear, colourless and practically odourless liquid for use on TRANS PAINT Colour Waves fully automated
dispenser as a washing liquid for pump nozzles to prevent blockage and caking of residue colourants.

Purity 99.5 min % (m/m)

Colour Clear & Colourless

Density 1036 kg/m3

Boiling Point 187.4 0C

Flash Point 103 0C

Dynamic Viscosity 55 mPa.s

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

ECON WHITE EMULSION

An economical emulsion that offers a whiter and tougher paint film for the best price.

Colour White

Pack Size 18 liters

Composition Binder Vinyl acetate/ acrylic ester copolymer emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 36  2%

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Overcoating Interval * 2 hours minimum

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss
Biocidal Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Nu-Cote Wall Sealer/ Pluss AP Sealer

Finish (2 coats) Econ White Emulsion

Plywood/Asbestos Primer (1 coat) Pluss QD Undercoat

Finish (2 coats) Econ White Emulsion

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

ECONLITE EMULSION

A cost-effective emulsion paint specially formulated for interior walls. It gives a very comfortable and non-reflective
appearance and has strong resistance against algae and fungus.

Colour See Econlite Emulsion Colour Card

Pack Size 7 liters

Composition Binder Vinyl acetate/ acrylic ester copolymer emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 35  2% for standard white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * 2 hours minimum

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Nu-Cote Wall Sealer/ Pluss AP Sealer

Finish (2 coats) Econlite Emulsion

Plywood/Asbestos Primer (1 coat) Pluss QD Undercoat

Finish (2 coats) Econlite Emulsion

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE EMULSION

A vinyl acrylic emulsion paint specially formulated for tropical weather. It is suitable for all types of interior surfaces. It is
durable, colourfast and fungus-resistant.

Standard Approved to Malaysian Standard 903:1984 (Cert. No. PT001301)

Colour 9102 White (standard colour)
Colours available via Colour Waves

Pack Size 5 and 20 liters (1L available via Colour Waves)

Composition Binder Vinyl acetate-acrylic ester copolymer emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 28  2% for standard white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry  Ensure surface is clean and dry
 Apply appropriate sealer  Remove lose paint film by hard scraping/
high pressure water jet

 Treat fungi, algae or mould with Pluss
Biocidal Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Nu-Cote Wall Sealer/ Pluss AP Sealer

Finish (2 coats) Nu-Cote Emulsion

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE FLOOR

Nu-Cote Floor is a general purpose pure acrylic waterborne floor coating for sealing concrete floors and prevent concrete
floor dusting and to improve the decorative floor appearance. This product dries rapidly to a tough, alkali resistant finish
which will withstand considerable wear, abrasion, grease, oils, and cleaning equipment. It can be used both interiorly and
exteriorly over prepared concrete and wood floors, steps, stairwells, aisle ways, or previously painted floor surfaces in
sound condition.

Colour Colours available via Colour Waves only

Pack Size 1, 5 and 20 liters

Composition Binder Pure acrylic emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid Average 36  2%, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry/ Wood
 Ensure surface is cured,  Remove lose paint film by hard scraping/ high
clean and dry pressure water jet

 Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/ Masonry/ Wood Finish (2 coats) Nu-Cote Floor

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE GLAZE

An acrylic emulsion that gives a brilliant pearlescent/ metalline luster effect to your walls. Suitable for both exterior and
interior application.

Colour Pearlescent – White, Silver, Violet, Orange, Pink, Green, Blue, Yellow, Indigo
Metalline – Gold, Bronze, Red Wine
(See Nu-Cote Glaze in Contemporary Shades 2008)

Pack Size 100 ml

Composition Binder Pure acrylic emulsion
Pigment Pearlescent/ Metalline effect pigments
Solvent Water

Volume Solid 36  2% for white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 10% by volume
Airless Spray Thin with water to 5% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface

 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Primer (1 coat) Pluss AP Sealer

Finish (3 coats at least) Nu-Cote Glaze

Note: The colours for this product are translucent. For best result, apply over a

solid base coat/ primer of the same colour or white. Colours and effects

depend very much on base coat/ primer and the number of coats for the

finishing.

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE GLOSS

A premium enamel paint, fungus resistant and suitable for all surfaces, both interior and exterior. It is easy to apply and
has excellent gloss and durability.

Standard Approved to Malaysian Standard 125:1995 (Cert. No. PT001303)

Colour 9102 White (standard colour)
Colours available via Colour Waves

Pack Size 1 and 5 liters

Composition Binder Long-oil alkyd
Pigment Inorganic and organic pigments
Solvent Hydrocarbon mixture

Volume Solid 48  2% for standard white, varying with colours

Recommended Dry Film thickness 30 microns (per coat)

Drying Times * Touch Dry Within 4 hours
Through Dry Within 8 hours

Over-coating Interval * Minimum 10 hours

Spreading Rate * 15 – 17 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with paint
Conventional Spray thinner or white spirit/ mineral turpentine if necessary
Airless Spray Thin with paint thinner or white spirit/ mineral
turpentine to 20% by volume
Use as is

Surface Preparation New Unpainted Surface Previous Painted Surface

Ferrous  Remove rust or mill scales by manual  Remove loose adhering paint

or mechanical cleaning  Remove debris, oil, grease or other

 Ensure surface free from oil, grease contaminant before painting

and other contaminant  Use suitable primer

Wooden  Ensure surface free from oil, grease  Remove loose adhering paint
Recommended Painting System  Ensure surface is clean and dry
and other contaminant

 Sand surface with abrasive paper for

better adhesion and appearance

Sequence Product

Wooden Primer (1 coat) Pluss Aluminium Wood Primer

Undercoat (1 coat) Pluss QD Undercoat

Finish (2 coats) Nu-Cote Gloss

Ferrous Primer (1 coat) Pluss Industrial Zinc Phosphate Primer

Undercoat (1 coat) Pluss QD Undercoat

Finish (2 coats) Nu-Cote Gloss

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE OCEANGLO

A premium lustrous, highly durable and washable luxury wall finish. Specially formulated for interior walls to provide a
smooth and mid sheen finish, it is suitable for most room conditions with limited tolerance against high atmospheric
humidity such as kitchens and bathrooms.

Colour 9102 White (standard colour)
Colours available via Colour Waves

Pack Size 5 and 20 liters (1L available via Colour Waves)

Composition Binder Pure acrylic emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 38  2% for standard white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 10 – 11 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry  Ensure surface is clean and dry
 Apply appropriate sealer  Remove lose paint film by hard
scraping/ high pressure water jet

 Treat fungi, algae or mould with Pluss
Biocidal Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Pluss AP Sealer

Finish (2 coats) Nu-Cote OceanGlo

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE RICH

A premium vinyl acetate ethylene emulsion finish designed for both style and performance on interior walls. It exerts
superb richness especially in bright colours and its elegant eggshell finish gives an overall luxurious feel. A tougher paint
film provides for a long-lasting beauty to the living spaces. Formulated with low VOC content and both heavy metal and
formaldehyde free.

Colour 9102 White (standard colour)
Colours available via Colour Waves

Pack Size 5 and 20 liters (1L available via Colour Waves)

Composition Binder Vinyl acetate acrylic polymer emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 38  2% for standard white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 1 hour
Through Dry Within 2 hours

Over-coating Interval * Minimum 2 hours

Spreading Rate * 10 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Nu-Cote Wall Sealer/ Pluss AP Sealer

Finish (2 coats) Nu-Cote Rich

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE TIMBER

A quick drying transparent paint based on polyurethane alkyd for a glossy and abrasion resistant finish. It is most suitable
on new parquet floors, furniture, wood paneling and wooden doors.

Colour Clear Glossy and Coloured
(See Nu-Cote Timber in Contemporary Shades 2008)

Pack Size 1 and 5 liters

Composition Binder Polyurethane modified alkyd
Pigment Not applicable
Solvent Hydrocarbon mixture

Volume Solid 48  2% for standard clear, varying with colours

Recommended Dry Film thickness 20 – 25 microns (per coat)

Drying Times * Touch Dry Within 4 hours
Through Dry Within 8 hours

Over-coating Interval * Minimum 10 hours

Spreading Rate * 19 – 24 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
Conventional Spray paint thinner or white spirit/ mineral turpentine if
necessary

Thin with paint thinner or white spirit/ mineral
turpentine to 20% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Wooden  Remove loose adhering paint
 Ensure surface free from oil,  Ensure surface is clean and dry
grease and other contaminant

 Sand surface with abrasive paper
for better adhesion and
appearance

Recommended No. of Coat 2 to 3 coats

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE UVROOF

A premium quality, highly durable, 100% acrylic water based eggshell finish. This decorative coating has excellent
resistant against algae and mildew, sunlight as well as alkali attack. It can be painted on new or old roofs made of
unglazed tile, aluminum or metal roofing.

Colour See Nu-Cote UVRoof Colour Card (via Colour Waves only)

Pack Size 1, 5 and 20 liters

Composition Binder Pure acrylic emulsion
Pigment Lightfast inorganic, organic pigments and mineral
extenders
Solvent Water

Volume Solid Average 38  2%, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 5 m2/ liter/ coat (varies with roughness and porosity of substrate

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Unglazed Tiles/ Aluminium/ Metal
Roofing  Ensure surface is clean  Remove lose paint film by hard scraping/ high
and dry pressure water jet

 Apply appropriate sealer  Treat fungi/algae/mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Sound Unglazed Tiles Primer -

Finish (2 coats) Nu-Cote UVRoof

Chalky Unglazed Tiles Primer (1 coat) Pluss AP Sealer

Finish (2 coats) Nu-Cote UVRoof

Aluminium Primer -

Finish (2 coats) Nu-Cote UVRoof

Metal Roofing Primer -

Finish (2 coats) Nu-Cote UVRoof

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE UVWOOD

A high quality 100% acrylic emulsion paint specially designed for exterior timber or other wood surface such as fences,
walls, balconies and cladding. It is also suitable on galvanized iron such as gutters, fencing and roof sheets. It exhibits
excellent adhesion and high resistant to algal as well as mildew inhibition. It is specially formulated for tropical climate
with high humidity and extensive sunlight exposure. No priming is needed on timber to avoid staining.

Colour See Nu-Cote UVWood Colour Card (via Colour Waves only)

Pack Size 1, 5 and 20 liters

Composition Binder Pure acrylic emulsion
Pigment Lightfast inorganic, organic pigments and mineral
extenders
Solvent Water

Volume Solid Average 40  2%, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 10 m2/ liter/ coat (varies with roughness and porosity of substrate

Application Brush/Roller Use as is, thin not exceeding 5% by volume with water if
necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Wood/ Timber/ Galvanised Iron
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product
Sound Primer -
Finish (2 coats) Nu-Cote UVWood
Chalky Primer (1 coat) Pluss AP Sealer
Finish (2 coats) Nu-Cote UVWood

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE WALL SEALER

A premium quality styrenated-acrylic emulsion based sealer that exerts good alkali resisting property on interior and
exterior masonry surfaces.

Colour White

Pack Size 5 and 20 liters

Composition Binder Styrene/ acrylate copolymer emulsion
Pigment Inorganic, organic pigments and mineral pigments
Solvent Water

Volume Solid 31  2%

Recommended Dry Film thickness 20 – 30 microns (per coat)

Drying Times * Touch Dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 7 - 9 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray
Airless Spray

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Nu-Cote Wall Sealer

Finish (2 coats) Nu-Cote Weather, Nu-Cote Emulsion, Nu-Cote

Oceanglo

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

NU-COTE WEATHER

A high quality 100% acrylic emulsion paint with excellent resistance to natural weathering and fungus growth for
decoration and protection of exterior building surfaces.

Standard Approved to Malaysian Standard 134:2007 (Cert. No. PT001302)

Colour 9102 White (standard colour)
Colours available via Colour Waves

Pack Size 5 and 20 liters (1L available via Colour Waves)

Composition Binder Pure acrylic emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 36  2% for standard white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss
Biocidal Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Nu-Cote Wall Sealer/ Pluss AP Sealer

Finish (2 coats) Nu-Cote Weather

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

PLUSS ALUMINIUM WOOD PRIMER

A solvent based primer for use on all types of wood surfaces and for both interior and interior applications.

Standard Equivalent to Malaysian Standard 289:1985

Colour Aluminium

Pack Size 5 liters

Composition Binder Modified hydrocarbon derivative
Pigment Aluminium flakes
Solvent Hydrocarbon mixture

Volume Solid 45  2%

Recommended Dry Film thickness 25 – 30 microns (per coat)

Drying Times * Touch Dry Within 1 hour
Through Dry Within 4 hours

Over-coating Interval * Minimum 8 hours

Spreading Rate * 15 – 18 m2/ liter/ coat

Application Brush Use as is
Conventional Spray
Use as is, thin not exceeding 5% by volume with
paint thinner or white spirit/ mineral turpentine if
necessary

Surface Preparation New Unpainted Surface Previous Painted Surface
Wooden  Remove loose adhering paint
 Ensure surface free from oil,  Ensure surface is clean and dry
grease and other contaminant  Use suitable primer

 Sand surface with abrasive
paper for better adhesion and
appearance

Recommended Painting System Sequence Product

Wooden Primer (1 coat) Pluss Aluminium Wood Primer

Undercoat (1 coat) Pluss QD Undercoat

Finish (2 coats) Nu-Cote Gloss

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

PLUSS ADHESION PROMOTING (AP) SEALER

A solvent-based sealer specially formulated for any masonry surfaces where excellent adhesion and alkaline resisting
properties are required for lasting protection. Minimal surface preparation for all weather application.

Colour White

Pack Size 5 liters

Composition Binder Styrene acrylate and styrene butadiene copolymer
Pigment Inorganic and mineral pigments
Solvent Hydrocarbon mixture

Volume Solid 45  2%

Recommended Dry Film thickness 35 microns (per coat)

Drying Times * Touch Dry Within 30 minutes
Through Dry Within 2 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 13 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
paint thinner or white spirit if necessary
Conventional Spray
Airless Spray

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry  Ensure surface is clean  Remove visible flakes or peels
 Wash surface

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Pluss AP Sealer

Finish (2 coats) Nu-Cote Weather, Nu-Cote Rich, Nu-Cote Emulsion,

Nu-Cote OceanGlo

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

PLUSS BIOCIDAL WASH

A ready to use aqueous chemical solution which has a broad-spectrum biocide for use in aqueous sterilizing solutions, and
also for the preparation of biocidal wash solutions used for surface preparation prior to painting. When properly use it
will enable the decoration of treated surfaces to be carried out with minimal risk of re-infection from the old surface,
masonry or wooden substrates. It could be used for both interior and exterior application.

Colour Clear amber liquid

Pack Size 5 liters

Composition Active Ingredient Combination of alkyl dimethyl benzyl ammonium
Solvent chloride and 2-phenyl-phenol
Water

Drying Times * 2-3 hours

Application Method Shake container before use. Apply by brush to affected areas. Leave for 24 hours.
Remove the dead growth with a stiff brush or power washer. Rinse thoroughly.
Where the degree of infection is higher, it may be necessary to repeat the process.
Do not apply in wet weather. In case of rain during the drying period, reapply the
solution. Never use this biocidal wash in the present of hypochlorite solution.

Spreading Rate * Depending on the absorbency of the surface

Application Brush/ Roller Use as is, do not thin

Surface Preparation New Unpainted Surface Previous Painted Surface

Concrete/ Masonry  Ensure surface is  Remove lose paint film by hard scraping/ high

clean and dry pressure water jet

 Remove any mould, algae or lichen especially

those entrapped underneath the coating by stiff

brush, scrapper or power washer

 Ensure dry off before apply

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

PLUSS INDUSTRIAL ZINC PHOSPHATE PRIMER

A semi-gloss anti-corrosive primer with zinc phosphate for the protection of steel work in harsh industrial environments.

Colour Greygreen

Pack Size 1 and 5 liters

Composition Binder Modified medium-oil alkyd
Pigment Zinc phosphate and inert mineral extenders
Solvent Hydrocarbon mixture

Volume Solid 50  2%

Recommended Dry Film thickness 35 – 45 microns (per coat)

Drying Times * Touch Dry Within 2 hour
Through Dry Within 6 hours

Over-coating Interval * Minimum 16 hours

Spreading Rate * 11 – 14 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
paint thinner or white spirit/ mineral turpentine if
Conventional Spray necessary
Airless Spray Thin with paint thinner or white spirit/ mineral
turpentine to 20% by volume
Use as is

Surface Preparation New Unpainted Surface Previous Painted Surface
Ferrous
 Remove rust or mill scales by  Remove loose adhering paint
manual or mechanical cleaning  Remove debris, oil, grease or other

 Ensure surface free from oil, contaminant before painting
grease and other contaminant

Recommended Painting System Sequence Product

Ferrous Primer (1 coat) Pluss Industrial Zinc Phosphate Primer

Undercoat (1 coat) Pluss QD Undercoat

Finish Nu-Cote Gloss

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

PLUSS QD UNDERCOAT

An oil-modified alkyd based undercoat designed specially for both wooden and metal surfaces. Its superb hiding and build
serves as a terrific foundation for Nu-Cote Gloss.

Standard Approved to Malaysian Standard 132:1993 (Cert. No. PT001304)

Colour White

Pack Size 1 and 5 liters

Composition Binder Oil-modified alkyd
Pigment Titanium dioxide and mineral extenders
Solvent Hydrocarbon mixture

Volume Solid 56  2%

Recommended Dry Film thickness 35 microns (per coat)

Drying Times * Touch Dry Within 4 hours
Through Dry Within 8 hours

Over-coating Interval * Minimum 10 hours

Spreading Rate * 15 – 17 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with paint
Conventional Spray thinner or white spirit/ mineral turpentine if necessary
Airless Spray Thin with paint thinner or white spirit/ mineral
turpentine to 20% by volume

Use as is

Surface Preparation New Unpainted Surface Previous Painted Surface

Ferrous  Remove rust or mill scales by  Remove loose adhering paint
manual or mechanical cleaning  Remove debris, oil, grease or other

 Ensure surface free from oil, contaminant before painting
grease and other contaminant  Use suitable primer

Wooden  Ensure surface free from oil,  Remove loose adhering paint
grease and other contaminant  Ensure surface is clean and dry
 Use suitable primer
 Sand surface with abrasive paper
for better adhesion and
appearance

Recommended Painting System Sequence Product

Wooden Primer (1 coat) Pluss Aluminium Wood Primer

Undercoat (1 coat) Pluss QD Undercoat

Finish (2 coats) Nu-Cote Gloss

Ferrous Primer (1 coat) Pluss Industrial Zinc Phosphate Primer

Undercoat (1 coat) Pluss QD Undercoat

Finish (2 coats) Nu-Cote Gloss

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

TRANS PAINT Technical Data Sheet (TDS)

PLUSS ROAD LINE

An alkyd/ chlorinated rubber based coating for the marking of concrete and asphalt surfaces. It is fast drying and has high
chemical resistance and recoating properties.

Standard Equivalent to Malaysian Standard 164:1991

Colour White, Yellow and Black (non-reflective)

Pack Size 5 liters

Composition Binder Alkyd/ Chlorinated rubber
Pigment Titanium dioxide and mineral extenders
Solvent Hydrocarbon mixture

Volume Solid Average 50  2%, varying with colours

Recommended Dry Film thickness 50 – 60 microns (per coat)

Drying Times * Touch Dry Within 1 hour
Through Dry Within 2 hours

Over-coating Interval * Minimum 3 hours

Spreading Rate * 9 – 10 m2/ liter/ coat

Application Brush/Roller Use as is

Surface Preparation Surfaces must be clean, dry and free from loosely adhering particles. For new
surfaces, 1 to 2 coats of paint are usually required.

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

SNO-COTE EMULSION

An economical emulsion paint formulated specially for interior use in tropical climate. It is easy to apply, fungus resisting
and has reasonably good washability.

Standard Equivalent to Malaysian Standard 903:1984
Also available via Colour Waves

Colour See Sno-Cote Emulsion Colour Card

Pack Size 7 and 18 liters (1L available via colour tinting system)

Composition Binder Vinyl acetate acrylic polymer emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 35  2% for standard white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 1 hour
Through Dry Within 2 hours

Over-coating Interval * Minimum 2 hours

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) TOP Emulsion Sealer

Undercoat (1 coat) Sno-Cote Undercoat

Finish (2 coats) Sno-Cote Emulsion

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

SNO-COTE UNDERCOAT

An economical emulsion undercoat that has good built and superb coverage. It is specially formulated for the
undercoating of Sno-Cote Emulsion paint.

Colour White

Pack Size 7 and 18 liters

Composition Binder Vinyl acetate/ acrylic ester copolymer emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 32  2%

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 8 – 11 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface

Concrete/ Masonry  Ensure surface is clean and  Remove lose paint film by hard scraping/ high

dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss Biocidal

Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) TOP Emulsion Sealer

Undercoat (1 coat) Sno-Cote Undercoat

Finish (2 coats) Sno-Cote Emulsion, Sno-Cote Xglo

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

SNO-COTE XGLO

A high quality vinyl acrylic based emulsion paint with a brilliant sheen finish for an improved stain resistance property on
interior walls.

Colour 9102 White (standard colour)
Colours available via Colour Waves

Pack Size 5 and 18 liters (1L available via Colour Waves)

Composition Binder Vinyl acrylic based emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 35  2% for standard white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) TOP Emulsion Sealer

Finish (2 coats) Sno-Cote Xglo

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

SNO-COTE XTRA WEATHER

A high quality acrylic based emulsion paint with excellent resistance to natural weathering and fungus growth for
decoration and protection of exterior building surfaces.

Colour See Sno-Cote Xtra Weather Colour Card
Also available via Colour Waves

Pack Size 5 and 18 liters (1L available via Colour Waves)

Composition Binder Acrylic emulsion
Pigment Inorganic, organic pigments and mineral extenders
Solvent Water

Volume Solid 36  2% for standard white, varying with colours

Recommended Dry Film thickness 30 - 40 microns (per coat)

Drying Times * Touch dry Within 30 minutes
Through Dry Within 1 hour

Over-coating Interval * Minimum 2 hours

Spreading Rate * 9 – 12 m2/ liter/ coat

Application Brush/Roller Use as is, thin not exceeding 5% by volume with
water if necessary
Conventional Spray Thin with water to 20% by volume
Airless Spray Thin with water to 10% by volume

Surface Preparation New Unpainted Surface Previous Painted Surface
Concrete/ Masonry
 Ensure surface is clean and  Remove lose paint film by hard scraping/ high
dry pressure water jet

 Apply appropriate sealer  Treat fungi, algae or mould with Pluss Biocidal
Wash

 Ensure dry off before painting

Recommended Painting System Sequence Product

Concrete/Masonry Primer (1 coat) Nu-Cote Wall Sealer/

Pluss AP Sealer/ TOP Emulsion Sealer

Finish (2 coats) Sno-Cote Xtra Weather

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>

TRANS PAINT Technical Data Sheet (TDS)

TOP ALUMINIUM 250

A high gloss architectural decorative aluminium paint for wooden and metallic surfaces both interior and exterior. Its
brilliant reflective property serves as a protective finish for storage tanks, ducting and pipes in the tropical climate.

Standard Equivalent to Malaysian Standard 289:1985

Colour Aluminium

Pack Size 1, 5 and 18 liters

Composition Binder Modified hydrocarbon derivative
Pigment Aluminium flakes
Solvent Hydrocarbon mixture

Volume Solid 45  2%

Recommended Dry Film thickness 25 – 30 microns (per coat)

Drying Times * Touch Dry Within 1 hour
Through Dry Within 4 hours

Over-coating Interval * Minimum 8 hours

Spreading Rate * 15 – 18 m2/ liter/ coat

Application Brush Use as is
Conventional Spray
Use as is, thin not exceeding 5% by volume with
paint thinner or white spirit/ mineral turpentine if
necessary

Surface Preparation New Unpainted Surface Previous Painted Surface
Ferrous
 Remove rust or mill scales by  Remove loose adhering paint
Wooden manual or mechanical cleaning  Remove debris, oil, grease or other

 Ensure surface free from oil, contaminant before painting
grease and other contaminant  Use suitable primer

 Ensure surface free from oil,  Remove loose adhering paint
grease and other contaminant  Ensure surface is clean and dry
 Use suitable primer
 Sand surface with abrasive paper
for better adhesion and
appearance

Recommended Painting System Sequence Product

Wooden Finish (2 coats) TOP Aluminium 250

Ferrous Primer (1 coat) TOP Greygreen Oxide 437

Finish (2 coats) TOP Aluminium 250

* Based on recommended thickness; will vary considerably with surface characteristics, application techniques, weather and wastage.

The corresponding Safety Data Sheet (SDS) for this product shall be provided upon request. Further inquiry and SDS request can be
made to [email protected]

Manufactured by: Trans-Ocean Coatings & Chemicals Sdn Bhd. Lot 1393, Jalan Meranti, Bintawa Industrial Estate, 93450 Kuching,
Sarawak, Malaysia. Tel: +6082 334 222 Fax: +6082 339 189 Website: www.transpaint.yungkong.com

Disclaimer:
While every care has been taken to ensure the accuracy of the information contained in this data sheet, it is provided in good faith
and that no liability can be accepted arising from its use. Where the conditions of use warrant it, it is recommended that the data are
checked to ensure their suitability for the use envisaged.

Revision: 7 Jan 2016 <end of document>