Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
PRECAUTIONS FOR USE OF GAS SPRINGS
-GUIDE-
IPrecautions for use of gas springs 1. 2. 3.
If a gas spring is used in the following ways, a major accident, such as an explosion, or product trouble may occur. 70A
Gas spring
IDanger prevention
1Never disassemble, weld, fuse, heat or modify a gas spring. Gas cylinder Working ambient
temperature: 0 ~ 40BC
A gas spring contains high-pressure gas. If you fail to heed this precaution, its parts may burst out. Gas springs temperature:below 70BC
2You cannot recharge the gas or adjust its pressure. Never disassemble, weld, fuse, heat or modify a gas spring. Do not recharge the gas , or adjust its pressure. Wear protective goggles, bleed off the gas
If you attempt to do so, a major accident, such as an explosion, may to occur. The working ambient temperature(around a die)is 0~40BC. and then dispose the gas spring.
3The working ambient temperature (around a die) is 0 ~ 40BC (32 ~ 104BF). 4. Plate 5. 6.
Use a gas spring within this range.
If a gas spring is heated over 70A, a major accident, such as an explosion, may occur. Also, the gas seal deteriorated by heat Equivalent to 40HRC
may result in gas leakage.
Do not apply oblique load or transverse load. Do not mount gas spring by piston rod side, Fix the gas spring with bolts or a flange.
IDisposal method attach an extension pin, or apply partial load. 9.
4Wear protective goggles. Make a hole that passes through the bolt hole, bleed off the gas from the cylinder, and then dispose of the
7. 8.
gas spring.
Make that the nitrogen gas has been bled off completely.
IGas leakage prevention
5Do not use the gas spring in the following ways.
Failure to observe these precautions may result in gas leakage and other troubles. Also a major accident, such as an explosion, may
occur.
Use sub-guide pins to prevent the Apply load evenly. Never grind the cylinder
eccentric load. or cut the piston rod.
Usage that are considered problematical Phenomena that may occur Result
10. 11. 12.
a Application of an oblique load or a transverse load. Eccentric load Gas leakage
b Gas spring is not fixed with bolts. and/or OSLvihmeoritt!
c No sub-guide components are not used, or lack of components. Damage Gas leakage,
d The load distribution at the front, rear, left and right of the inside the die is not equal. explosion, etc. Prevent clinging of welding spatter, Do not exceed the shot limit. Do not immerse the gas spring in lubricating oil.
e There is an obstacle touching the gas spring inside the die. Seal damage cutting chips and metalic dust. 15.
f Mounting gas spring by the tap hole on top of the piston rod. 14.
g An extension pin is mounted on the piston rod end. Reduction of durability 13.
h The piston rod is not pushed flatly. Unexpected problems The overstroke check-pin is crushed
i Surface of the piston rod is deformed. when stroke exceeds its limit.
j Cutting the piston rod. S
SM0.9 Recommended
k Welding spatter clings to the piston rod.
l Cutting chips and metallic dust cling the piston rod. Damage
m The piston rod is dented.
n Exceeding the shot limit. (Avoid using as a ejector pin or an extrusion pin.)
o The gas spring is immersed in lubricating oil.
p The gas spring is exposed to moisture, steam or chemicals. Never use or store the gas spring Do not use in exceeding stroke limit. Do not release the piston rod abruptly.
outdoors or under humid condition.
q Recharging the gas or adjusting its pressure. 17. IAllowable eccentricity Catalog No. Allowable eccentricity
r The gas spring is used at high temperatur(e 40BC or above)or low temperatur(e 0BC or below). 16.
s Overstroking Use other than If you apply an eccentric GSX
t Grinding the cylinder. in a die load, gas leakage may occur. GSE 0.3/100mm
u Releasing the piston rod abruptly.
v Use or strange of the gas spring outdoors or under humid condition. GSM
w Disassembling, welding, fusing, heating or modifying the gas spring. GSC
x Incorporating the gas spring into a building or a vehicle.
y Other unexpected us(e other than in a die) MGSC 0.02/100mm
MGSA
MGSB
GSSR
Do not incorporate the gas spring Do not use other than in a die.
into a building or a vehicle.
Press 2007 http://misumi.jp/press/
1103 Express P.38 For inquiry, ordering and 1104
service system other information, refer to
P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service. Up to 16%
GAS SPRINGS
-COMPACT HEAVY DUTY-
GSX When a gas spring is used exceeding the range of stroke length(S), it will cause gas leakage
and the piston rod will not return. Make sure to use a gas spring within the range of stroke length
GSX32 GSX38~63 so that nothing makes contact with the overstroke check pin. Allowable eccentricity
2-Ma Gas-charge hole 4-Ma Gas-charge hole GFor specs on plates, refer to the right-hand page.
Shape A
0 F3.2 The life of the gas spring is affected by the eccentric load.
df8 If an eccentric load that exceeds the allowable value is
D -0.2 applied, the life of the gas spring may be reduced.
J
Assembly hole 2-F6 Assembly hole 2-Fe 0 2
-0.5 S:Stroke
De H
38 6
50 7 LÚ0.3 AM(Plate only) The allowable eccentricity of GSX is 0.3/100 mm which is
63 8 15 times of that of other products. (The allowable
Shape B AM–32 AM–38 eccentricity of other products is 0.02/100 mm.)
Consequently, GSX prevents reduction of life due to
4–F6.6 4–F6.6 eccentric loading. (This also applies to GSE.)
You cannot use the gas-charge hole or the assembly 0 F2
hole for installing products. df8
The positional relationship of the assembly holes and D -0.2
the spanner groove is not necessarily the same. J
Charged pressure of nitrogen gas MPa{kgf/cm2} 9
P
GSX32 18.7{191} K a Catalog No. Allowable eccentricity
S:Stroke A
GSX38 18.4{188} 0 P GSX
-0.5 a GSE
A GSM
H P GSC
GSX50 19.2{196} 0.3/100mm
bb
GSX63 19.2{196} LÚ0.3 BB
Catalog No. Components Cylinder body Piston rod(Contact face) Piston rod
S45C NAK55 SCM435
GSX32-10 - - 700HV~(Surface) SS400 MGSC 0.02/100mm
GSX38-10 Nitriding+Grinding finish Fe3O4(Black oxide) MGSA
Fe3O4(Black oxide) 37~43HRC SCM435
(Shape A) S45C - 750HV~(Surface) Bolt A B a b P Catalog No. U/Price MGSB
- - Hardening+Grinding finish Q'ty:1~9 GSSR
GSX32~63 -
Fe3O4(Black oxide)
(Shape B)
Shape Weight D Ma K Load N{kgf} Catalog No. U/Price FB6–16M2 pcs. 51 32 41 22 15
A (kg) 32 Initial load Max. load Q'ty:1~9 FB6–16M4 pcs. 57 38 47 28 20
B d L H Tapped holes J Type D–S AM 32 1,380
A 0.30 38 14,690 38 1,520
B 0.32 50 for mounting 15,730
0.36 63 16,730
B 0.43 75 65 7200 { 734} 32-10 17,680
0.46 18,570
B 0.51 85 70 8000 { 816} 32-15 19,380
0.57 20,280
0.43 105 80 4750 8600 { 877} 32-25 19,440 It is recommended that the bolts be coated with locking paint before use.
0.46 20,380
0.52 18 135 97 M6M9 15 2 8850 { 902} 32-38 21,260 IShot limit
0.61 22,220
0.66 155 105 {484} 9250 { 943} 32-50 23,030
0.73 24,080
0.83 185 122 9300 { 948} 32-63 24,630 IEndurance test result Stroke(mm) 10 15 25 38 50 63 80
0.90 27,510
0.97 220 140 9350 { 953} 32-80 28,530 GSX
1.08 29,690
1.18 75 65 15000 {1530} 38-10 30,590 GSX32-50 GSX50-15 GSX63-38 Shot count limi(t spm) 220 165 100 65 50 40 35
1.27 31,240 48mm 13mm 35mm
1.42 85 70 17200 {1754} 38-15 31,820 Amplitude 45spm 70spm 65spm Shot count limit: The number of shots per minute
1.70 40,690 Excitation speed The shot count limit is sometimes affected by the working environment.
1.85 105 80 9030 18400 {1876} 38-25 42,540 Mounting direction Tilt 0.3/100 Tilt 0.3/100 Tilt 0.3/100 The figures shown here are reference values.
2.00 44,830 Forced air cooling Forced air cooling
2.15 25 135 97 M6M9 20 2 19100 {1948} 38-38 47,440 IGas spring temperature range
2.35 50,430
155 105 {921} 19700 {2009} 38-50 The working ambient temperature is 0 to 40A. Ensure that the temperature of the gas spring
does not exceed 70A.
185 122 19800 {2019} GSX 38-63 Cooling method Forced air cooling
38-80
220 140 19900 {2029}
110 95 24000 {2447} 50-15
130 105 19000 26000 {2651} 50-25
{1937}
35 155 117 M8M11 25 3 28000 {2855} 50-38
180 130 29000 {2957}
30500 {3110} 50-50
205 142 50-63 ILoad characteristics graph of GSX
240 160 31500 {3212} 50-80 [N] [kgf]
130 105 43500 {4436} 63-25 4 55000 {5608} K N=kgfM9.80665 K kgf=NM0.101972
155 117 31000 47000 {4793} 63-38 GSX63–50 GSX63–63 GSX63–80
45 180 130 M8M11 35 3 49000 {4997} 63-50 50000 {5099} GSX63–38
205 142 {3161} 51000 {5201} 63-63 2
240 160 52500 {5354} 63-80 45000 {4589} GSX63–25
The initial load and maximum load vary depending on the temperature and operation speed. The load tolerance for temperature variation is Ú10%.
1 0 40000 {4079}
2 -2
(B) -4
(2 )B -6
-8
(2 )B -10
Load reduction rate(%)
Load{N}0
K kgf=NM0.101972 K N=kgfM9.80665 K Charged pressure of nitrogen gas kgf/cm2=MPaM10.1972 MPa=kgf/cm2M0.0980665
Catalog No. 1Delivery Day IVolume discount rate P.37 35000 {3569} GSX50–38 GSX50–50 GSX50–80
30000 {3059} GSX38–38 GSX38–50 GSX50–63
Order GSX 32-38 Price Quantity 1~9 10~19 20~39 40~99 GSX32-50 25000 {2549} GSX50–25 GSX38–63 GSX38–80
AM-32 Rate - 5% 10% 15% GSX50-15 20000 {2039} GSX50–15
GSX63-38 15000 {1530}
To be quoted on price & lead time above Max. Q'ty. GSX38–15 GSX38–25
GSX38–10
IDetailed dimensions of Shape A(GSX32-10,GSX38-10) Shape B Detailed view of the end
the end of the piston rod
d This dimension is determined from the d d 10000 {1020} GSX32–10 GSX32–15 GSX32–25 GSX32–38 GSX32–50 GSX32–63 GSX32–80
20Bangle and the 2mm length, so it is (d3) (d3) 5000 { 510}
(d2) (VB)
da not covered by a dimensional standard.
F3 (d1) 0
0 10 20 30 40 50 60 70 80
5B 20 40 60 80 100
Number of strokes(ten thousands) Stroke[mm]
The end shape of the GSX32-10 and Type (d1) (d2) (d3) d V B The parenthesized This graph shows the quasi-static characteristics.
38-10 piston rods are shape A, but dimensions are reference Actual characteristics vary depending on temperature and operation speed.
they may be changed to shape B GSX32 2.5 5.3 12 18 20 3 values.
without prior notice. However, the L 20B Type d da GSX38 2.5 5.3 16 25 20 3
dimension remains unchanged. GSX32-10 18 12 GSX50 3.0 6.5 22 35 15 4
(The change date has not been GSX38-10 25 18 GSX63 3.0 6.5 26 45 15 4
decided.)
1105 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1106
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service. Up to 10%
GAS SPRINGS
-COMPACT TYPE-
GSM (Main body) When a gas spring is used exceeding the range of stroke length(S), it will cause gas leakage and the piston rod will not return.
GSMH(HM plate set) Make sure to use a gas spring within the range of stroke length so that nothing makes contact with the overstroke check pin.
GSMF(FM plate set)
GFor specs on plates, refer to the right-hand page.
Do not fix the gas spring using the screw hole at the end or, install an extension pin. P.1104
GSM19C25 GSM32~63 (H-2)Ú0.25
Ma 2-Ma M
0 GSMH(Set parts) HM(Plate only) GSMF(Set parts) FM(Plate only)
-0.2
Hole for FB5
R
D
J F3
d
D HM19C25 4-F6.6 HM32~63 4-F6.6
t
Mb K h2 aHole for FB
Mb cannot be used for mounting. H S:Stroke A
P
Charged pressure of nitrogen gas MPa{kgf/cm2} LÚ0.3 a
A
GSM 19 19.1{195} Piston rod t
SACM645 6.5
1000HV~(Surface) a1
Nitriding+Barrel finishing a2
A
GSM 25 19.5{199} 4-Fd
GSM 32 19.7{201} bb b
BB B
GSM 38 20.5{209} Cylinder body
SCM440 or equivalent SS400 Bolt FB5-10:2pcs.
GSM 50 20.9{213} Fe3O4(Black oxide) Fe3O4(Black oxide) S45C Semicircle ring:2 pcs.
Fe3O4(Black oxide)
GSM 63 18.9{193}
Weight D d M LH Ma J Load N{kgf} Catalog No. U/Price Q'ty:1~9 Bolt A B a b P t Catalog No. U/Price A B a1 a2 b d D t R Catalog No. U/Price
(kg) Initial load Max. load GSM GSMH GSMF Q'ty:1~9 Q'ty:1~9
h K Tapped holes Mb Type D-S 11,640 12,410 13,770 19 19
for mounting 12,340 13,110 14,470 25 1,000 25 2,500
13,530 14,300 15,660 1,100 2,600
0.10 85 70 2100{ 214} 19-15 14,730 15,500 16,860 38 28 28 18 HM 32 1,380 44 28 33 28 18 19 22.0 FM 32 3,460
15,590 16,360 17,720 FB6-16M1 pc 44 28 34 18 - 1,520 3,820
0.11 105 80 2180{ 222} 19-25 16,120 16,890 18,250 38 1,690 50 30 38 34 18 25 25.0 38 4,310
13,230 14,070 15,490 51 32 41 22 15 50 1,830 50 4,950
0.14 19 10 M5M 7 135 97 23 (R21)M6M 8 - - 1500 2250{ 229} 19-38 13,360 14,170 15,550 FB6-16M2 pcs. 57 38 47 28 63 57 39 46 40 22 6.6 32 11 28.5 63
0.16 160 110 {153} 2330{ 238} 14,620 15,430 16,880
19-50 15,680 16,490 17,940 69 50 59 40 20 9
16,620 17,430 18,880 FB8-20M2 pcs. 84 65 70 50
0.19 190 127 2420{ 247} 19-63 17,250 18,060 19,510 63 46 53 45 26 38 31.5
15,160 16,440 18,370
0.21 220 140 2510{ 256} 19-80 16,240 17,520 19,450 75 58 64 54 34 50 37.5
17,260 18,540 20,470
0.21 85 70 4500{ 459} 25-15 18,250 19,540 21,460 98 76 86 74 40 9.0 63 13 49.0
19,170 20,460 22,390
0.23 105 80 4800{ 489} 25-25 20,010 21,300 23,230
20,930 22,220 24,150
0.26 25 14 M6M 8 135 97 23 (R21)M6M 8 - 3000 4800{ 489} 25-38 20,490 21,880 23,980 Catalog No. IEndurance test result
0.29 160 110 - {306} 4950{ 505} 21,470 22,860 24,960
25-50 22,400 23,800 25,900 Order GSM 32-25 Catalog No. GSM38-15 GSM38-50
23,410 24,800 26,900 Delivery GSMH 38-38 Amplitude 15mm 50mm
0.35 190 127 5100{ 520} 25-63 24,260 25,660 27,760 HM - 32 Excitation speed 200 60
25,370 26,770 28,870 Mounting direction Erect Erect
0.38 225 145 5280{ 538} 25-80 25,960 27,360 29,460 1 Day
28,270 29,780 32,110
0.32 75 65 7500{ 765} 32-10 29,100 30,610 32,940
30,190 31,720 34,080
0.32 85 70 7750{ 790} GSM 32-15 31,420 32,950 35,310
32-25 32,360 33,890 36,250
0.36 105 80 2 M6M 5000 8000{ 816} (Main body) 32-38 33,070 34,600 36,960 Initial load 10000N
(R1) {510} 8000{ 816} 33,670 35,200 37,560 {1020kgf}
0.43 32 18 M8M12 135 97 26 8 M4M 8 15 8250{ 841} 38,140 39,840 42,740
160 110 39,040 40,740 43,640
0.48 32-50 39,850 41,550 44,450 IVolume discount rate P.37
41,660 43,360 46,260
0.58 195 132 8500{ 867} 32-63 43,900 45,600 48,500 Price Quantity 1~9 10~19 20~39 40~99 9750N
46,460 48,160 51,060 {994kgf}
0.64 230 150 8800{ 897} GSMH 32-80 49,390 51,090 53,990 Rate - 5% 10% 15%
38-10
0.44 75 65 15500{1581} (HM plate set) 38-15 To be quoted on price & lead time above Max. Q'ty.
0.46 85 70 16000{1632} IShot limit 9500N GSM38-50
{969kgf} GSM38-15
0.52 105 80 12 (R21)M6M 8 M8M 8 10000 16500{1683} 38-25
M8M12 135 97 {1020} 16500{1683} Stroke (mm) 10 15 25 38 50 63 80
0.61 38 25 20 17000{1733} 38-38
160 110 GSM
0.68 GSMF 38-50 Shot count 250 165 100 65 50 40 30 9250N
38-63 limit {943kgf} 0 10 30 50
0.83 205 142 17500{1785} (FM plate set) 38-80 (spm) 100
0.98 240 160 18000{1835} Shot count limit: The number of shots per minute Number of strokes(ten thousands)
The shot count limit is sometimes affected by the working environment.
1.05 90 80 28000{2855} 50-10 IGas spring temperature range
The figures shown here are reference value.
1.10 115 100 29200{2978} 50-15 The working ambient temperature is 0 to 40A. Ensure that the temperature
1.19 135 110 13 4 M8M12 M8M12 20000 30000{3059} 50-25 ILoad characteristics graph of GSM of the gas spring does not exceed 70A.
M8M12 165 127 (R2) {2039} 32000{3263}
1.28 50 35 20 33000{3365} 50-38 N {kgf} N=kgfM9.80665 kgf=NM0.101972 N {kgf} N=kgfM9.80665 kgf=NM0.101972
190 140 9000 {918} GSM32-38 GSM32-50 GSM32-63 GSM32-80
1.40 50-50 60000{6118}
1.66 220 157 33600{3426} 50-63 55000{5608} GSM63-80 8000 {816} GSM32-10 GSM32-15 GSM32-25
50000{5099} GSM63-63
1.90 255 175 34000{3467} 50-80 45000{4589} GSM63-50
GSM63-38
1.66 95 85 42900{4375} 63-10 GSM63-15 GSM63-25 7000 {714}
GSM63-10
1.80 115 100 44700{4558} 63-15 6000 {612}
1.94 135 110 30000 46200{4711} 63-25 40000{4079} GSM25-38 GSM25-50 GSM25-63 GSM25-80
M8M12 165 127 {3059} 48300{4925}
2.18 63 45 12(R52.5)M8M12 M8M12 20 51000{5200} 63-38 35000{3569} GSM50-38 GSM50-50 GSM50-63 GSM50-80 5000 {510} GSM25-25
190 140 GSM25-10 GSM25-15
63-50 GSM50-15 GSM50-25
2.34 30000{3059} GSM50-10 4000 {408}
2.65 220 157 52200{5323} 63-63 25000{2549}
2.95 255 175 53700{5476} 63-80 20000{2039} 3000 {306} GSM19-38 GSM19-50 GSM19-63 GSM19-80
GSM38-10 GSM19-10 GSM19-15 GSM19-25
The initial load and maximum load vary depending on the temperature and operation speed. The load tolerance for temperature variation is Ú10%. GSM38-15 GSM38-25 GSM38-38 GSM38-50 GSM38-63 GSM38-80
2000 {204}
15000{1530}
K kgf=NM0.101972 K N=kgfM9.80665
1000 {102}
K Charged pressure of nitrogen gas kgf/cm2=MPaM10.1972 MPa=kgf/cm2M0.0980665 10000{1020} 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
0 Stroke[mm] Strok[e mm]
When mount GSM32, 38, 50, or 63, be sure to use mounting holes of Ma and two bolts.
1107 This graph shows the quasi-static characteristics.Actual characteristics vary depending on temperature and operation speed. 1108
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
GAS SPRINGS GAS SPRINGS
-SHORT TYPE- -HEAVY LOAD MINI TYPE-
GSC (Main body) When a gas spring is used exceeding the range of stroke length(S), it will cause gas leakage and the piston rod will not return. MGSC When a gas spring is used exceeding the range of stroke length(S), it will cause gas leakage and the piston rod will not return.
GSCB (BM plate set) Make sure to use a gas spring within the range of stroke length so that nothing makes contact with the overstroke check pin. Make sure to use a gas spring within the range of stroke length so that nothing makes contact with the overstroke check pin.
Do not fix the gas spring using the screw hole at the end or, install an extension pin. P.1104 Ma
Ma (H-1)Ú0.25
(H-1)Ú0.25
M
0 F3 D -00.2
-0.2 d F1.5
D d
1
1 H S:Stroke
LÚ0.3 LÚ0.3
H S:Stroke
Charged pressure of nitrogen gas MPa{kgf/cm2} Cylinder body Piston rod Charged pressure of nitrogen gas MPa{kgf/cm2} Cylinder body Piston rod
GSC 32 14.7{150} SCM440 or equivalent SACM645 MGSC 16 20.0{204} SCM440 or equivalent SACM645
GSC 38 19.7{201} Fe3O(4 Black oxide) 1000HV~(Surface) MGSC 19 21.6{220} Fe3O4(Black oxide) 900HV~(Surface)
GSC 50 21.2{216} Nitriding+Barrel finishing MGSC 25 20.4{208} Nitriding+Grinding finish
Weight D dML H Ma Load N{kgf} Catalog No. U/Price Q'ty:1~9 Weight Ma Load N{kgf} Catalog No. U/Price
(kg) 32 Tapped holes (kg) Q'ty:1~9
38 for mounting Initial load Max. load Type D-S GSC GSCB D d L H Tapped holes
0.23 50 Type D-S
0.23 - 55 45 6710{ 684} 32-10 17,910 19,190 for mounting Initial load Max. load
0.24
0.26 65 50 6750{ 688} 32-15 18,370 19,650 0.06 55 45 1550{158} 16-10 6,400
0.28
0.47 18 85 60 M 6M 8 3750 6860{ 700} 32-25 19,450 20,730 0.06 16 8 65 50 M5M7 1000 1650{168} 16-15 6,810
0.26 M6M 8 111 73 {382} 6940{ 708} 0.07 85 60 {102} 1750{178} 16-25 7,200
0.28 32-38 20,570 21,860
0.36
0.40 135 85 6980{ 712} 32-50 21,600 22,890 0.07 111 73 1800{184} 16-38 7,860
0.46
0.65 195 115 7000{ 714} 32-80 22,320 23,610 0.08 55 45 2750{280} 19-10 6,600
0.60
0.62 - 55 45 13500{1377} GSC 38-10 23,620 25,020 0.09 19 10 65 50 1700 2850{291} 19-15 6,970
0.71 38-15 0.10 85 60 {173} 2950{301} 19-25 7,530
0.82 65 50 13880{1415} (Main body) 24,200 25,590 M5M7 MGSC
0.92
1.15 85 60 7500 14030{1431} 38-25 25,250 26,650
22 M6M 8 111 73 M 8M12 {765} 14100{1438}
GSCB 38-38 26,390 27,780 0.11 111 73 3100{316} 19-38 7,860
38-50
135 85 14250{1453} (BM plate set) 38-80 27,350 28,750 0.14 55 45 6000{612} 25-10 7,970
195 115 14320{1460} 28,640 30,040 0.15 25 15 65 50 3600 6550{668} 25-15 8,330
0.16 85 60 {367} 6800{693} 25-25 8,690
60 50 27750{2830} 50-10 32,130 33,640 M6M8
70 55 28500{2906} 50-15 32,800 34,310 0.18 111 73 6950{709} 25-38 9,190
90 65 M10M12 15000 28950{2952} 50-25 34,020 35,550
30 M8M12 116 78 {1530} 29400{2998}
50-38 35,410 36,940 The initial load and maximum load vary depending on the temperature and operation speed. The load tolerance for temperature variation is Ú10%. Ckgf=NM0.101972 CN=kgfM9.80665
CCharged pressure of nitrogen gas kgf/cm2=MPaM10.1972 MPa=kgf/cm2M0.0980665
140 90 29500{3008} 50-50 36,480 38,010
200 120 29700{3029} 50-80 37,990 39,520 IEndurance test result ILoad characteristics graph of MGSC
The initial load and maximum load vary depending on the operation speed. The load tolerance for temperature variation is Ú10%. Ckgf=NM0.101972 CN=kgfM9.80665 Catalog No. MGSC19-25 MGSC19-38 N {kgf} N=kgfM9.80665 kgf=NM0.101972
CCharged pressure of nitrogen gas kgf/cm2=MPaM10.1972 MPa=kgf/cm2M0.0980665
Amplitude 23mm 35mm 7000{714}
MGSC25-15 MGSC25-25
IShot limit Excitation speed 120spm 65spm
MGSC25-38
Stroke(mm) 10 15 25 38 50 80 Mounting direction Erect Erect 6000{612} MGSC25-10
GSC Initial load 5000{510}
2000N
Shot count limit(spm) 250 165 100 65 50 30 {204kgf}
Shot count limit : The number of shots per minute 1750N MGSC19-25 4000{408}
The shot count limit is sometimes affected by the working environment. {178kgf} MGSC19-38 3000{306}
The figures shown here are reference values.
GSCB (Set parts) BM (Plate only) 4–F6.6 MGSC19-10 MGSC19-15 MGSC19-25 MGSC19-38
IGas spring temperature range
Hole for FB 1500N 2000{204} MGSC16-15 MGSC16-25 MGSC16-38
The working ambient temperature is 0 to 40A. Ensure that the temperature of the {153kgf} MGSC16-10
gas spring does not exceed 70A.
t
a ILoad characteristics graph of GSC
A
N {kgf} N=kgfM9.80665 kgf=NM0.101972 1250N 1000{102} 10 20 30 40
{127kgf} 0 Stroke[mm]
30000{3059}
GSC50-10 GSC50-15 GSC50-25 GSC50-38 GSC50-50 GSC50-80
b 25000{2549} 1000N 10 20 30 40 50 60 70 80 90 100 This graph shows the quasi-static characteristics.
B {102kgf}0 Number of strokes(ten thousands) Actual characteristics vary depending on temperature and operation speed.
SS400 20000{2039} IShot limit
Fe3O4(Black oxide)
Order Catalog No. Stroke(mm) 10 15 25 38
15000{1530} GSC38-10 GSC38-15 GSC38-25 GSC38-38 GSC38-50 GSC38-80 MGSC 19-25
U/Price GSC32-80 MGSC
Bolt A B a b t Catalog No. Q'ty:1~9 10000{1020}
9 Shot count limi(t spm) 170 150 90 50
FB 6-16M1pc. 51 32 41 22 32 1,380 GSC32-10
FB 8-20M1pc. 57 38 47 28 1,520 5000{ 510} GSC32-15 GSC32-25 GSC32-38 GSC32-50 1Delivery Day Shot count limit : The number of shots per minute
FB10-20M1pc. 69 50 59 40 BM 38 1,690 The shot count limit is sometimes affected by the working environment.
The figures shown here are reference values.
50
Catalog No. 0 IGas spring temperature range
GSC 32-25 0 10 20 30 40 50 60 70 80
Order GSCB 38-38 Stroke[mm] IVolume discount rate P.37 The working ambient temperature is 0 to 40A. Ensure that the temperature of the
Delivery BM - 32 gas spring does not exceed 70A.
This graph shows the quasi-static characteristics. Price Quantity 1~9 10~19 20~39 40~99
1 Day
Actual characteristics vary depending on temperature and operation speed. Rate - 5% 10% 15%
IVolume discount rate P.37 To be quoted on To be quoted on price & lead time above Max. Q'ty.
price & lead time
Price Quantity 1~9 10~19 20~39 40~99 above Max. Q'ty.
10% 15%
1109 Rate - 5% Express For inquiry, ordering and 1110
service system other information, refer to
P.38 Press 2007 http://misumi.jp/press/ P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
GAS SPRINGS GAS SPRINGS
-MINI TYPE- -THREADED TYPE-
MGSA (Main body : regular type) When a gas spring is used exceeding the range of stroke length(S), it will cause gas leakage and the piston rod will not return. MGSB When a gas spring is used exceeding the range of stroke length(S), it will cause gas leakage and the piston rod will not return.
MGSAH(H plate set) Make sure to use a gas spring within the range of stroke length so that nothing makes contact with the overstroke check pin. Make sure to use a gas spring within the range of stroke length so that nothing makes contact with the overstroke check pin.
MGSAF(F plate set)
Do not fix the gas spring using the screw hole at the end, or install an extension pin. P.1104
Ma
(H-1)Ú0.25 L1Ú0.3
H S:Stroke
M M (Fine thread) 45B 2 1 3
F3
0 0 d 0
-0.2 1-0.2
D-0.2
F3 2 D
d D
K h1
H S:Stroke L2 3
(H-1)Ú0.25
LÚ0.3
Charged pressure of nitrogen gas MPa{kgf/cm2} Cylinder body Piston rod Charged pressure of nitrogen gas MPa{kgf/cm2} Cylinder body Piston rod
S45C SACM645 SACM645
MGSA 19 10.2{104} Fe3O4(Black oxide) SACM645 MGSB 12 12.0{122} Nitriding+Fe3O4(Black oxide) 1000HV~(Surface)
MGSA 25 1000HV~(Surface) Nitriding+Barrel finishing
Nitriding+Barrel finishing MGSB 16 10.1{103}
Weight D dML H h K Ma Load N{kgf} Catalog No. Weight MMP Load N{kgf} Catalog No. U/Price
(kg) 19 (kg) D1 (Fine thread) Initial load Max. load Q'ty:1~9
55 Initial loadTapped holes Max.load Type D-S D2 d L1 H L2 Type M-S
0.08 25 60 19-10 12,800
0.08 70 for mounting 13,500
0.11 83 11,500
0.11 65 95 1200{122} 12,200
0.13 125 13,500
0.17 75 55 1260{128} 19-15 0.03 5 75 65 400{41} 640{ 65} 12-10
0.15 60 14 10.2 M12MP1.25 27
0.16 10 M5M7 95 70 18 2 M6M6 800{ 82} 1270{130} MGSA 19-25 12-15
0.19 121 83 (R1) 1280{131} 0.04 90 75
0.22 95
0.25 125 (Main body) 19-38 0.05 75 65 MGSB 16-10
0.33
145 1290{132} 19-50
205 1300{133} MGSAH 19-80 0.06 18 14.2 8 90 75 M16MP1.5 37 800{82} 1280{131} 16-15
25-10
65 2520{257} (H plate set) 0.07 120 95 16-25
75 2560{261} 25-15
14 M6M8 95 2 M6M6 1600{163} 2600{265} MGSAF 25-25 The initial load and maximum load vary depending on the temperature and operation speed. The load tolerance for temperature variation is Ú10%. Ckgf=NM0.101972 CN=kgfM9.80665
121 (R1) 2620{267} 25-38 CCharged pressure of nitrogen gas kgf/cm2=MPaM10.1972 MPa=kgf/cm2M0.0980665
18 (F plate set)
145 2640{269} 25-50 Catalog No. IEndurance test result
MGSB 12-15
205 2660{271} 25-80 Order Catalog No. MGSA 19-25 MGSB 16-15
15mm
The initial load and maximum load vary depending on operation speed. The load tolerance for temperature variation is Ú10%. Ckgf=NM0.101972 CN=kgfM9.80665 Amplitude 25mm 135SPM
CCharged pressure of nitrogen gas kgf/cm2=MPaM10.1972 MPa=kgf/cm2M0.0980665 Erect
Excitation speed 120SPM
MGSAH(Set parts) H(Plate only) 4–F6.6 Catalog No. 1Delivery Day Mounting direction Erect
Order MGSA 19-80
MGSAH 25-10
Hole for FB F-25 IVolume discount rate 3 P.37 883N
3 {90kgf}
Price Quantity 1~9 10~19 20~39 40~99
Rate Initial load-5%10%15%
t
a 1Delivery Day To be quoted on price & lead time above Max. Q'ty. 834N
A {85kgf}
IVolume discount rate P.37 IHow to Install F22 785N MGSA
{80kgf} 19-25
F18
b Price Quantity 1~9 10~19 20~39 40~99
B Rate - 5% 10% 15%
MGSB
SS400 To be quoted on price & lead time above Max. Q'ty. M12M1.25 735N 16-15
Fe3O4(Black oxide) (Fine thread) {75kgf} 0 5 10 20 30 40 50 60 80 100
Bolt A B a b t Catalog No. U/Price U/Price Q'ty:1~9 M16M1.5 Number of strokes (ten thousands)
9 Q'ty:1~9 (Fine thread)
1,000 The higher load values shown in the above graph
1,100 D-S Main Body H Plate Set F Plate Set (up to repeated use of approximately 300,000 times)
FB6-16M1pc. 38 28 28 18 H 19 MGSA MGSAH MGSAF Prepare a tapped hole for the MGSB gas cushion as shown in are due to friction between the rod and special urethane seal.
FB6-16M1pc. 44 34 25 the diagrams above to make the cushion's flange remain fit with
the hole's surface. The flange not only protects the cushion from ILoad characteristic graph for MGSACMGSB
19-10 12,200 13,100 14,500 excessive tightening, but it also helps prevent it from loosening.
MGSAF(Set parts) Hole for FB5 F(Plate only) 19-15 12,800 13,700 15,100 N{kgf} K kgf=NM0.101972 K N=kgfM9.80665
R 19-25 13,500 14,400 15,800 Applicable wrench:Use a PJG series spring plunger
19-38 14,900 15,800 17,200 wrench( P.781 )
19-50 16,200 17,100 18,500 2,800 {286}
19-80 17,500 18,400 19,800 2,550 {260} MGSA25-15 MGSA25-25 MGSA25-38 MGSA25-50 MGSA25-80
25-10 14,200 15,200 16,600 MGSA25-10
25-15 14,900 15,900 17,300
t D 25-25 15,500 16,500 17,900 ILimit shot 2,300 {235}
6.5 25-38 16,900 17,900 19,300
a1 25-50 18,200 19,200 20,600
a2 25-80 19,500 20,500 21,900
A
Stroke(mm) 10 15 25 2,050 {209}
MGSB Shot count 200 130 80
limit(spm)
1,800 {184}
4–Fd b Shot count limit: The number of shots per minute 1,550 {158}
B The shot count limit is sometimes affected by the working environment. MGSA19-10 MGSA19-15 MGSA19-25 MGSA19-38 MGSA19-50
The figures shown here are reference values. MGSA19-80
Bolt FB5-10:2pcs. 1,300 {133} MGSB16-10 MGSB16-15 MGSB16-25
Semicircle ring IShot limit
SS400 IGas spring temperature range
Fe3O4(Black oxide) Stroke(mm) 10 15 25 38 50 80 1,050 {107}
30 The working ambient temperature is 0 to 40BC. Ensure that the
U/Price MGSA Shot count 250 165 100 65 50 temperature of the gas spring does not exceed 70BC. 800 { 82}
limit(spm) MGSB12-10 MGSB12-15
A B a1 a2 b d D t R Catalog No. Q'ty:1~9 MGSB is not an oil-free product.
19 2,500 550 { 56}
2,600 After applying running-in grease, grease the piston rod every
44 28 33 28 19 22 F 25 Shot count limit: The number of shots per minute 300 { 31}
50 30 38 34 18 6.6 25 11 25 The shot count limit is sometimes affected by the working environment. 50,000 shots. Molybdenum disulfide(MOS2)grease is
The figures shown here are reference values. recommended for greasing. 0 10 20 30 40 50 60 70 80
IGas spring temperature range This graph shows the quasi-static characteristics. Stroke(mm)
1111 The working ambient temperature is 0 to 40BC. Ensure that the Actual characteristics vary depending on temperature and operation speed. 1112
temperature of the gas spring does not exceed 70BC.
Express P.38 Press 2007 http://misumi.jp/press/ For inquiry, ordering and P.1269
service system other information, refer to
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
GAS SPRINGS
-ISO/CNOMO STANDARD TYPE-
GSE When a gas spring is used exceeding the range of stroke length(S), it will cause gas leakage and the piston rod
will not return. Make sure to use a gas spring within the range of stroke length.
GSE38~50
Do not fix the gas spring using the screw hole at the end, or install an extension pin. P.1104
GSE75~150 T (H-Q)-00.5
T
M
Ma Ma D -00.2FJ F+00.1GÚ0.2 Kh Q FC
J D1Ú0.3 S:Stroke
d
g
e
a
A
h
tk
B
H SF KF
0 FC
-0.5
L
Charged pressure of nitrogen gas MPa {kgf/cm2} Cylinder body Piston rod
GSE38~150 15.0 {153} S45C or equivalent
Black coating SCM435
800HV~(Surface)
Hard chrome plating+Special finish
(Finishing may be changed to nitriding without prior notice.)
Weight D D1 d M LH h K T F Ma Q Load N {kgf} Catalog No. U/Price 4 –Fd1 4 –Fd1
(kg) Initial load Max. load Type D-S Q'ty:1~19
G Tapped holes J BfB
A
for mounting
0.5 100 75 3650{ 372} 38- 25 12,250 A
0.6 38 33 15 M6M11 150 100 9.5 (R21)10.5 4 4 2-M6M10 25 2 2650 {270} 3590{ 366} 38- 50 12,820
0.7 210 130 3570{ 364} 38- 80 14,150
3560{ 363} 38-100 16,430 S45C Bolt with hex socke(t CB):4 pcs.
0.8 250 150 S45C Bolt with hex socke(t CB):4 pcs. Fe3O4(Black oxide)
Fe3O(4 Black oxide) Spring washer:4 pcs. Spring washer:4 pcs.
1.1 135 110 6520{ 665} 45- 25 21,750 Semicircle ring:2 pcs.
1.2 185 135 6730{ 687} 45- 50 23,100
1.5 45 40 20 M8M8 245 165 13.5 (R21)15.5 4 4 2-M8M10 20 2 4710 {481} 6820{ 696} 45- 80 24,320 Bolt A a B C d1 e f g Catalog No. U/Price Bolt A B C d1 h k t Catalog No. U/Price
1.6 285 185 6860{ 699} 45-100 25,530 4pcs. Q'ty:1~19 4pcs. Q'ty:1~19
6880{ 702} 45-125 27,050 4
1.8 335 210 CB 6-18 55 40 19 56.5 7 4 17 6 38 2,800 CB 6-20 68 40 56.5 7 17 7.5 9 38 2,800
8
2.0 405 245 6910{ 704} 45-160 28,720 CB 8-18 70 50 25 70.7 9 8 20 6 45 3,400 CB 8-25 86 50 70.7 9 23 10 13 45 3,400
8
1.4 145 120 10980{ 1120} 50- 25 24,700 CB12-30 75 56.5 22 80 14 8 31 12 50 3,800 CB 8-25 95 56.5 80 9 24 10 13 50 3,800
8 75 4,300
1.7 195 145 11460{ 1168} 50- 50 26,220 CB12-30 100 73.5 32 104 14 36 12 SF CB10-30 122 73.5 104 11 29 12.5 16 KF 75 4,300
1.9 255 175 12.5 (R42)12.5 11670{ 1190} 50- 80 28,025 CB16-35 120 92 44 130 18 32 12 95 4,800 CB12-35 150 92 130 14 33 15 18 95 4,800
7360 {751} 11750{ 1198} 50-100 29,165
2.1 50 43 25 M8M13 295 195 8 7 2-M8M10 20 3 50-125 30,305 CB16-35 140 109.5 50 155 18 40 12 120 5,200 CB12-35 175 109.5 155 14 36 15 21 120 5,200
2.4 345 220 11810{ 1204}
CB20-40 190 138 75 195 18 40 12 150 6,700 CB16-50 220 138 195 18 41 20 27 150 6,700
2.7 415 255 11870{ 1210} 50-160 32,680
3.1 495 295 11910{ 1214} 50-200 34,200
3.6 160 135 21010{ 2142} 75- 25 33,250 ILoad characteristics graph of GSE
4.1 210 160 22150{ 2259} 75- 50 35,340 N {kgf} K kgf=NM0.101972 K N=kgfM9.80665 N {kgf} K kgf=NM0.101972 K N=kgfM9.80665
GSE150-100 GSE150-125 GSE150-160 GSE150-200 25000 {2549} GSE75-100 GSE75-125 GSE75-160
4.7 75 67 36 M8M13 270 190 15.5(R52.5)12 8 7 4-M8M15 40 3 15270 {1557} 22700{ 2315} 75- 80 37,050 140000{14280} GSE75-50 GSE75-80
5.1 310 210 22910{ 2336} 75-100 38,000 20000 {2039}
5.6 360 235 23080{ 2354} GSE 75-125 39,805 120000{12240} GSE150-80 GSE75-25
6.4 430 270 23240{ 2370} 75-160 42,805 GSE150-50
6.2 170 145 38960{ 3973} 95- 25 40,800 GSE150-25
100000{10197}
7.2 220 170 43000{ 4385} 95- 50 43,900
15000 {1530}
8.2 95 87 50 M8M13 280 200 18.5(R52.5)12 8 7 4-M8M15 60 3 29450 {3003} 45570{ 4647} 95- 80 45,500 80000 {8158} GSE120-80 GSE120-100 GSE120-125 GSE120-160 GSE120-200 GSE50-50 GSE50-80 GSE50-100 GSE50-125 GSE50-160 GSE50-200
8.9 320 220 46660{ 4758} 95-100 49,700 60000 {6118} GSE95-80 GSE95-100 GSE95-125 GSE95-160 GSE50-25 GSE45-160
40000 {4079} GSE120-50 10000 {1020} GSE45-50 GSE45-80 GSE45-100 GSE45-125
9.9 370 245 47640{ 4858} 95-125 52,800 GSE120-25 GSE38-50 GSE38-80 GSE38-100
GSE45-25
11.1 440 280 48590{ 4955} 95-160 58,300 GSE95-50 5000 {510}
GSE95-25
10.7 190 165 61070{ 6228} 120- 25 51,300 GSE38-25
12.2 240 190 67740{ 6907} 120- 50 54,000
14.0 300 220 20 (R52.5)12 72840{ 7428} 120- 80 59,500 20000 {2039} 0
120-100 65,200 0 20 40 60 80 100 120 140 160 180 200 0 20 40 60 80 100 120 140 160 180
15.2 120 112 65 M8M13 340 240 8 7 4-M10M18 80 3 49770 {5076} 75260{ 7674} 120-125 68,900 Strok(e mm) Strok(e mm)
16.7 390 265 77580{ 7911}
This graph shows the quasi-static characteristics.
18.9 460 300 80000{ 8157} 120-160 72,600
Actual characteristics vary depending on temperature and operation speed.
21.3 540 340 82000{ 8361} 120-200 84,600
20.5 205 180 102950 {10498} 150- 25 67,700
22.8 255 205 113220 {11545} 150- 50 72,100 IShot limit Catalog No.
25.4 315 235 119370 {12172} 150- 80 75,000 Stroke (mm) 25 50 80 100 125 160 200 Order GSE 75-80
150-100 81,900 50 35 30 25 20 15 KF75
27.3 150 141 80 M8M13 355 255 22 (R52.5)12 8 7 4-M10M18 100 3 75400 {7689} 121890 {12429} 150-125 86,200 GSE Shot count
29.6 405 280 124120 {12657} limit (spm)
100
32.7 475 315 126260 {12875} 150-160 91,900 Shot count limit: The number of shots per minute 3Delivery
The shot count limit is sometimes affected by the working environment.
36.4 555 355 127910 {13043} 150-200 99,800 The figures shown here are reference values. Days
The initial load and maximum load vary depending on the temperature and operation speed. The load tolerance for temperature variation is Ú10%. K kgf=NM0.101972 K N=kgfM9.80665
KCharged pressure of nitrogen gas kgf/cm2=MPaM10.1972 MPa=kgf/cm2M0.0980665
IGas spring temperature range IVolume discount rate P.37
The working ambient temperature is 0 to 40A. Ensure that Price Quantity 1~19 20~39 40~99 100~199
the temperature of the gas spring does not exceed 70A.
Rate - 5% 10% 15%
To be quoted on price & lead time above Max. Q'ty.
1113 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1114
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
GAS SPRINGS PATENT PENDING
-SLOW RETURN TYPE-
GSSR When a gas spring is used exceeding the range of stroke length(S), it will cause gas leakage and the piston rod will not return. IStructure Needle valve Never touch the needle valve stopper for your safety! IExample of use
Make sure to use a gas spring within the range of stroke length so that nothing makes contact with the overstroke check pin. If it comes off, the needle valve
stopper may jump out of the spring. GSSR
B Return speed Overstroke
adjusting hex hole check pin
Valve adjustment
Mb 2–Ma (H-1)Ú0.25
J Special Auxiliary pressure
F3 structure chamber
Fd
0 1
H L 0.3 S:Stroke Needle valve
D-0.2
Cylinder body
Mb cannot be used for mounting. SACM645 Piston rod Main pressure Tightening torque should GSSR
Nitriding+Fe3O4(Black oxide) SACM645 chamber be 500 NCcm or less.
Charged pressure MPa {kgf/cm2} 1000HV~(Surface)
of nitrogen gas Nitriding+Barrel finishing (Nitrogen gas)
GSSR50 7.0 {72}
Weight D d B L Ma Load N{kgf} Catalog No. U/Price When the piston rod goes down, As the nitrogen gas in the auxiliary pressure chamber reduces
(kg) Mb Q'ty:1~9 nitrogen gas flows into the auxiliary the pressure in the main pressure chamber, the return speed of
H Tapped holes J Type D-S pressure chamber. the piston rod slows down.
Initial load Max. load
for mounting
1.22 135 110 50-25 78,000
1.33 30 4 161 123 5000 9750 GSSR 50-38 80,000
50 M8M12 20 M8M12 {510} {994} 50-50 81,500
INotes ILoad
1.45 185 135 curve
CDo not use two or more gas springs, either on the die side or punch side. As it is difficult to
1.57 245 165 50-80 87,500 synchronize the return timings of plural gas springs, the die guide may burn out or the die may 10000 1000
be damaged. 7500
Catalog No. IFeatures 5000 750
GSSR 50-50 CIf the needle valve is tightened too much, the valve may be deformed, which leads to a 2500 Return stroke
Order CYou can adjust the return time (speed) of the piston rod by using the needle valve. (Insert an malfunction of the spring. Load [N]
Delivery Load [kgf] 500
Price Allen wrench into the return speed adjusting hex hole to adjust the needle valve.) CDo not turn the needle valve stopper. Although it has been bonded with adhesives, turning it
forcefully may cause gas leakage. 1.5 revolutions 2 revolutions 2.5 revolutions
Clockwise:The valve closes and the piston rod returns slower.
1 Day Counterclockwise:The clearance of the valve is enlarged and the piston rod CWhen GSSR is used with the slow return setting, use it at 10spm or less. Close Open
CThe working ambient temperature is 0 to 40A. Ensure that the temperature of the gas spring 250
returns faster as the nitrogen gas is encouraged to move from does not exceed 70A.
CGSSR can be used without oiling.
IVolume discount rate P.37 the auxiliary pressure chamber to the main pressure chamber. CFor the precautions for use, refer to P.1103. 0 10 20 30 40 50
CSince the piston rod can be adjusted to return slower, you can prevent the projecting rod Load curve of GSSR50-50 Stroke[mm]
(Loading rate 200mm/min)
Quantity 1~9 10~19 20~39 40~99 from damaging your product during drawing process.
Rate - 5% 10% 15% CHM-50 on P.1108 can be used as a mounting plate.
To be quoted on price & lead time above Max. Q'ty. IRelationship between the return time of the piston rod of the GSSR and the needle valve
GSSR50 series return time
Return speed [sec.] 8 50-25
7 50-38
6 1.0 2.0 3.0 4.0 50-50
5 Valve opening/closing [Rotation] Close 50-80
4
3 Open
2
1
0
0.5
This graph shows the mean value for 10 piston rods. Therefore, use it only as a reference.
1115 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1116
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
URETHANE SPRINGS
URETHANE URETHANES FOR HEAVY LOAD SQUARE URETHANES FOR HEAVY LOAD URETHANE STOCK BLOCKS URETHANES FOR HEAVY LOAD
SPRINGS EX QX EST"ESBT"ESU"ESUB"S"SU A
Name 1 3TA 11 1
Catalog No.
1121 1122 1122 1123
Delivery
Page
URETHANE STOCK BLOCKS URETHANES FOR HEAVY LOAD URETHANES WITH COUNTERBORE HOLE URETHANE SHEETS URETHANE DIE PADS
E EL LA"C AX"CX AZ AZX UT UTH UD UDH
1 3TA 3TA 1 3TA 1 3TA 1 3A 1 3A
1124 1125 1126 1127 1128
ECONOMY URETHANES HIGH DEFLECTION TYPE URETHANE FOAM (POROUS) URETHANES Low repulsion type With counterbore hole, Low repulsion type
AE"LAE"CE"AEX"CEX PA PLA AN"LAN"CNN ANX"CNX AZN AZNX
3 TA 11 1 3TA 1 3TA
1131"1132 1133 1134 1135
URETHANE SHEETS Low repulsion type URETHANE DIE PADS Low repulsion type
UTN UDN
1 1
1136 1136
01100107 1118
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
PRODUCTS INFORMATION PRODUCTS INFORMATION
URETHANE SPRINGS -GUIDE- OPTIMAL USAGE / PROCESSING METHOD
Physical properties and features DATA Relation between compression ratio and strokes per minute
Item Urethane springs for heavy loads High deflection type Low repulsion In order to control heat generation and accumulation as well as to increase durability of the urethane spring, pay attention to compression ratio and strokes per minute.
Economy type urethane foam(porous) urethane The following figures show the relation between various compression ratio and allowable strokes per minute, maintaining normal heat generation.
H type M type S type L type
Hardnes(s Shore A) 95 90 80 70 90 Not applicable 70 KUrethane springs for heavy loads Shore A70/90 KHigh deflection type urethane foam(porous)
EXCQXCEST ANCLANCCNN Heavy load type urethane shore A70 and 90 generate heat through High deflection Urethane foam(Porous)is less deformable than
ESBTCESU
ESUBCACECEL AECLAECCE ANXCCNXCAZN internal friction when deforming(Hysteresis effect). This heavy load Urethane. Its horizontal bulging when compressed is as
LACCCAXCCX AEXCCEX AZNXCUTN
Catalog No. TUSCUSCUSN AZCAZXCUT - - PACPLA phenomenon occurs when heavy load Urethane is pressurized half of heavy load Urethane, less heat reserve and is high in heat
UTHCUDCUDH
UDN rapidly. When machining with high speed, it is required to adjust generation. However, the amount of pressure and number of
deflection against strokes per minutes as shown below. strokes cause deterioration as for heavy load Urethane.
page P.685~P.688 P.1121~P.1128 - - P.1131~P.1132 P.1133 P.1134~P.1136
Tensile strength(N/cm2){kgf/cm2} 2941{300} 3138{320} 2452{250} 490{50} 1176{120}
4511{460} 4462{455} 250
250 -
Elongatio(n %) 450 550 500 650 540 - 6 Diameter
50 343{35} A F30~F80
300% Modulus(N/cm2){kgf/cm2} 1755{179} 1304{133} 931{95} 372{38} 1225{125} 294{30} 1.02 35 B F60~F80
1.16 1 C F100
Coefficient of restitution(%) 23 28 56 51 42 25 -20~+70 30 50 DCBA D F120
-5~+80 200 Shore A90 recommended
Tensile strength(N/cm2){kgf/cm2} 1206{123} 1147{117} 539{55} 451{46} 686{70} 230~250 -50 Recommended
-70 400 25 operating range range of usage
Characteristics 450
Specific gravity 1.28 1.27 1.26 20 Shore A70 recommended 40
Compressibility%
Compressibility%Permanent Strai(n %)*
26 24 27 25 27 18 operating range
Working ambient temperature(A) -20~+70 16
14 30
Melting temperatur(e A) 220 200 180 12
Embrittlement temperature(A) -70 -60 -45 10 20
9
Pyrophoric poin(t A) 500
8
Weather resistance Each type is excellent in weather resistance, and is superior to regular rubbers. 7 10
Water resistance Water resistant to small amount of water(. Do not use while being locked.) 6 200 300 400 600 800 1000
Oil resistance Oil resistant to small amount of cutting oil(. Do not use while being locked.) 20 30 40 60 80 100
Discoloration Discolors when exposed to ultraviolet ray(s including sunlight), but do not affect the usage. Discoloring of High deflection type urethane is relatively higher than the other types.
Strokes per minute
Low repulsion type urethanes should be used within the range 20 25 40 50 60 80 100 120 150 200 300 500
recommended for Shore A70. Strokes per minute
Although Possesses Although the The hardness is The allowance CPossesses both high Lower compressed
deflection is middle physical allowable load is as same as load and deflection(maximum of permanent strain,
lower, it has an properties lower, higher normal rubber permanent strain 40%)and high excellent performance
excellent between H and deflection allows but is excellent are somewhat allowance load. in shock absorbing Machining methods and cautions
capability in load S types, and deeper in abrasion lower than that CThe deflection is the and vibration proof. 1Move the materia(l urethane)as rapidly as possible so that heat will not build up internally.
2Slow machining causes heating up the material(Urethane), which resulting its elasticity loss and saw teeth or blades being stuck into the material.
Features bearing. suitable for formability. resistance and of M type, same but horizontal 3Be sure to give the cutting edge an acute angle and make the cutter as narrow as possible.
general mechanical however the cost bulging is half of M type.
purposes. strength. is lowered. CGood heat radiation
Thin stainless steel plates Machining of thin CHydroforming CDrawing Suitable for less Pad cushion, CVibration proof A. Cutting C. Grinding
CSoft material machining 1.Urethane can be easily cut with saws or band saws in the same manner as steel. 1.Cool while grinding and the appropriate circumferential speed of
Usag(e reference) or about 2mm thickness plates, aluminum CShallow drawing CGuerin method amount production cam return 2.When cutting with a lathe, set the speed high, grindstone is 100m/min.
such as films. the point at an acute angle and use thin blades. 2.The best grindstone material is GC with hardness K. The suitable grain size is 30~60.
steel plates machining. or brass. CWheelon method than M type. cushion etc. (This is the best methods to
have the work's parallelism.) D. Drilling
The above figure is the actual data measured at room temperature 23A, and not guaranteed. 1.Drilling can be done in the same manner as for steel.
B. Surface processing 2.When the tip of the drill is shaped as shown below, drilling can
*Measuring method of permanent strain’JIS K7312» 1.Urethane can be processed by millers, shapers, etc. be accomplished without deforming the material(urethane).
1)70AM24H 25% compression 2.Cutting speed 3.When machining holes, the internal diameter is contracted.
2)Cooled for 30 min. in the laboratory of room temperature 23A The circumferential speed of the milling cutter should be 40~60m/min.
3)Deformation measurement The cutting speed of shapers or planers should be at its maximum.
Comparison of urethane springs, coil springs, and gas cushions m:Excellent k:Average l:Fair M:Poor
Item Cost Machinability High speed Load stability Permanent strain Initial pressure Working ambient
performance endurance temperature
Urethane spring m k l llkk
Coil spring k M m mmlm
Gas cushions l M l mmml
1119 1120
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
URETHANES FOR HEAVY LOAD SQUARE URETHANES FOR HEAVY LOAD / URETHANE STOCK BLOCKS
The volume discount rate is also applicable to alteration cost. P.39
EX D Ú0.5 N kgf QX A
V
d Ú0.2
L Ú0.5 d 2A N kgf
F 1
2 F
Product guide P.1119 L V
Products information P.1137
Shore A90
F=LM20% F=LM25% F=LM30% U/Price Catalog No. 1 SS400
Catalog No. EX 8208
F Load F Load F Load D d L Order 2 2 Urethane
mm N kgf mm N kgf mm N kgf V Q'ty:1~19 Product guide P.1119 LM30% V=A Shore A90
12 6865 15 8924 18 12749 62 EX 5146 870 Catalog No.
16 700 20 910 24 1300 58 50 14
82 EX 5148 1,140 1Delivery F=LM20% F=LM25% F=LM30% d U/Price
14 Q'ty:1~19
12 9807 15 13239 18 18633 62 EX 6206 1,310 Day F Load F Load F Load Type A-L
16 1000 20 1350 24 1900 70 60 20 mm N kgf mm N kgf mm N kgf 20
82 EX 6208 1,670 12 9807 15 13239 18 18633 60 62 2,380
16 1000 20 1350 82 2,970
16 19123 20 26478 24 39227 82 2,970 24 1900
20 1950 25 2700 30 4000 103 3,670
92 80 20 EX 8208 Price 12 13729 15 18633 18 25497 62 3,350
EX 82010 1400 20 1900 24 2600 70 82 3,950
16 27
16 20 24 82 EX 10208 4,630 IVolume discount rate P.37 18 23 92 4,490
27949 38736 54427
20 25 30 114 100 20 103 EX 102010 5,600 Quantity 1~19 20~49 50~99 100~200 16 20 24 QX 82 6,970
20 25497 35304 49033
24 2850 30 3950 36 5550 123 EX 102012 6,680 Rate - 5% 10% 15% 2600 25 3600 30 5000 95 103 8,320
30 36
kgf=NM0.101972 To be quoted on price & lead time above Max. Q'ty. 24 123 9,720
Catalog No. -(C1) 20 39227 25 53937 30 73550 103 11,700
4000 5500 7500 120 123 13,800
Example Alterations EX 8208 - C1 24 30 36
3 Days 28 35 42
F F˘10 143 15,500
Alteration Code Spec. \/1Code kgf=NM0.101972
C1 Catalog No. 1Delivery IVolume discount rate P.37
Order 100~200
Day Price Quantity 1~19 20~49 50~99
QX 70-92 10% 15%
Rate - 5%
C1 C1 chamfering on the 100 To be quoted on price & lead time above Max. Q'ty.
inner diameter
Urethane stock blocks EST D ESBT ESU D ESUB
d
SGA P.1099 C1 d
EX D Ú0.5 N kgf
L Ú0.5 V 45B
F 5
12 1 2 Shore A90
r
r1 r2 r31 Catalog No. U/Price Q'ty:1~9 Catalog No.
d Urethane ESTCESBT ESUCESUB 2 ESTCESU ESBTCESUB EST 40-80
r Type D-L Order
L
LE40-80* 40- 80 710720
14 E50-110 S14 SU14 CB8-45 50-110 1,350 1,360 1Delivery Day
(1pc.)
E70-140 EST 70-140 2,890 2,900
Product guide P.1119 E7022110 ESBT * 7022110 2,390 2,420
Products information P.1137
Shore A90 E7022140 *ESU * 7022140 2,930 2,960 IVolume discount rate P.37
22 E90-120 S22 SU22 CB12-55 *ESUB 90-120 3,730 3,860 Price Quantity 1~9 10~19 20~49 50~100
E90-140 Rate - 5% 10% 15%
(1pc.) * 90-140 4,330 4,360
F=LM20% F=LM25% F=LM30% U/Price Catalog No. E100-140 100-140 6,770 6,800 To be quoted on price & lead time above Max. Q'ty.
D LF Catalog No. Q'ty:1~19 Order EX 100100
Load F Load F Load
Vmm N kgf mm N kgf mm N kgf ESU and ESUB are available only for the sizes marked with *. For applicable urethane P.1124
12 7551 15 9807 18 14710 58 50 62 EX 5060 870 Urethane U/Price
EX 5080 1,140 d Catalog No. Q'ty:1~19
16 770 20 1000 24 1500 82 EX 6060 1,310 Sleeves d1 d2 d3 d4 r R1 R2 R3
EX 6080 1,670
12 11082 15 15004 18 21575 70 60 62 EX 8080 2,970 Delivery 3 Days S SU Fd 4 16 9 30 14 S14 130
EX 80100 3,670 Price Fd 3 24 13
EX 10080 4,630 15B Fd 2 24 13 35 22 S22 170
EX 100100 5,600 14 9 13 19
16 1130 20 1530 24 2200 82 EX 100120 6,680 Express T 1,600/1Pc. P.38 22 13 20 27 100 22 S22-100 500
Express A 800/1Pc. (L170 or more)
16 20104 20 27753 24 41188 92 80 82 A flat charge of 2,160 yen for 3 pieces or more of the same size. 14 SU14 130
20 2050 25 2830 30 4200 103 30 7 10 3 SU22 170
22
16 20 24 82 (excluding Express T) Catalog No. 1 Day
S 14
20 29420 25 41188 30 61292 114 100 103 Order Delivery
Price
24 3000 30 4200 36 6250 123 IVolume discount rate Fd 2 Fd 1 IVolume discount rate P.37
Fd 1 Press 2007
kgf=NM0.101972 P.37 SS400 100~200 To be quoted on
15% price & lead time
Quantity 1~19 20~49 50~99 100~200 Quantity 1~19 20~49 50~99 above Max. Q'ty.
Rate - 5% 10%
10% 15% Rate - 5%
1121 To be quoted on price & lead time above Max. Q'ty. Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1122
service system other information, refer to
P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
URETHANES FOR HEAVY LOAD URETHANE STOCK BLOCKS
The volume discount rate is also applicable to alteration cost. P.39
A Standard type D N
kgf D D
d
L
E D N
kgf
D D
d
L
V 15
d 20 d
40 |0.2 |0.2 |0.3
25 |0.2 |0.2 |0.3
30 L
50
40 F V
70 |0.3 |0.2 |0.5
50
L 60 |0.3 |0.2 |0.5
90
F 80
100 |0.4 |0.2 |0.5 100 |0.4 |0.2 |0.5
110
Product guide P.1119 Shore A90
Product guide P.1119
Products information P.1137 Shore A90
F L+15 F L+20 F L+25 Dd L Catalog
No. U/Price
V
F L+15 F L+20 F L+25 Catalog
No. U/Price F Load F Load F Load
80 Type D L Q'ty 1O19
d mm N
kgf
mm N
kgf
mm N
kgf
110
Load V Type D
L
Q'ty 1O19 110 E
F Load F Load F N
kgf
18
7 A 15
25 12.0 4560
465
16 5394
550
20.0 06276
640
147
40 140 40
80 550
mm N
kgf
mm N
kgf
mm
24 8.5 30 40 170
981 35 40 16.5 7747
790
22 9218
940
27.5 10787
1100
159
50 110 50 110 1,160
3.8
5
6.3
100
30 11 40 40 16.5 22 27.5 140
7.5 A 20
25 40
70 14 170 70 110 2,110
4.5
588
6
785
8.8
1765
37 14 30 70 140
10
180
35 70 21.0 28 35.0
70 170 70 140 2,620
5.3
60
7
80
6.3
48 14 40 70 200
7.5
2648
60 14 A 25
25 70 25.5 18633 34 22555 42.5 24517
70 140 70 170 3,140
6
8
8.8
270
72 14 30 120
2500
181
70 140
10
95 22 35 120 16.5
1900
22
2300
27.5 170 7022110 2,110
3.8
5
6.3
3531 119 22 40 120 200
7.5
360
45 120 21.0 28 35.0
70 250 7022140 2,620
4.5
1128
6
1422
8.8
Alteration 50 120
10
6276 A 30
25 120 25.5 34 42.5
70 7022170 3,140
5.3
115
7
145
11.3
640
30 130
35 130 21.0 27459 28 33342 35.0 40207
90 90 140 3,950
6
8 12.5 10787 40 150
4100
105
90
1100 45 170 25.5
2800
34
3400
42.5 90 170 5,080
3.8
5
6.3 17652 50 190
90 22
7.5 1800 55 205 30.0 40 50.0 90 200 6,000
4.5
6
8.8 29420 60 235
10
3000
A 40
40 255 21.0 35990
3670
28 42659
4350
35.0 49720
5070
117 100 100 140 6,270
5.3
1667
7
2157 11.3 49720 50 310 21.0 28 35.0
5070
60 385 110 110 140 7,340
6
170
8
220
12.5 A 50
50 475
60 625 25.5 39226 34 47072 42.5 56878 110 110
17
0
9,190
6.8
9 13.8 80 740
5800
129 110
A 60
50 995 30.0
4000
40
4800
50.0 110 200 10,830
7.5 10 15
60 890
10
80 1,070 37.5 50 62.5 110 110 250 13,490
3.8
5 12.5 A 80
60 1,430
80 1,900
kgf N+0.101972
4.5
6 15
100 2,530 Catalog
No. 'Volume discount rate P.37
12.5 A 100
80 3,150 E
7022110 To be quoted on price &
5.3
7 100 3,950
Order
$D40O100
Price Quantity 1O19 20O49 50O99 100O200 lead time above Max. Q'ty.
15
120 4,930
Delivery 10 15
6
2599
8
3040 20
5,720 1 Day Rate 5
12.5 Catalog
No. C1
6.8
265
9
310
kgf N+0.101972
$D110
15
A
60 80
C1
7.5 10 20
3 Days 3 Days Express T 1,600/1Pc.
15
Express A 800/1Pc.
8.3 11 20
P.38
25
9 12 20
A flat charge of 2,160 yen for 3 pieces or more of the same siz e excluding Express T .
25
6
4560
8
5394 30
7.5 10 D
9
465
12
550
EL Full length specified type d D D
d
L
40 |0.2 |0.2 |0.3
7.5
7747 10
9218
50 |0.3 |0.2 |0.5
9
790
12
70
12
16
940
90 |0.2 |0.5
100 |0.4
7.5 13042 10 15102 110
9
1330
12
12
16
1540
L
9 21378 12 25399
12
2180
16
15
20
2590
12
35990 16 42659
Product guide P.1119 Shore A90
15
3670
20
18
24
4350
Catalog
No. L U/Price Q'ty 1O9
1mm increments L61O80 L81O100 L101O150 L151O200 L201O250
Type D d L15O20 L21O40 L41O60
15O200 230 380 570
Order Catalog No.
40 14 380 670 950 760 950 1,430 1,900
A 25 40
50 50O250 740
1,160 1,540 1,240 1,520 2,280 3,040
1,220 1,940 2,570
EL
70 14"22 4,280 1,900 2,190 3,040 4,370
90 5,230
Alteration Code Spec. 8/1Code 3,150 3,630 5,320 6,650
1
Delivery Day C1 100 4,280 5,040 7,410 8,740 11,120
110 22
C1 chamfering on the 5,230 6,460 9,220 11,880 14,730
C1 inner diameter
'Volume discount rate P.37 100
Quantity 1O19 20O49 50O199 200O400 Catalog
No. L 'Volume discount rate P.37
EL
70 22
Price Rate 5 10 15 C1
Order
Price Quantity 1O9 10O49 50O99 100O200
To be quoted on price & lead time above Max. Q'ty. 155 Rate 5 10 15
To be quoted on price & lead time above Max. Q'ty.
3
Delivery Days Express T 1,600/1Pc. P.38
Express A 800/1Pc.
A flat charge of 2,160 yen for 3 pieces or more of the same siz e excluding Express T .
1123 Express P.38 Press 2007 http://misumi.jp/press/ For inquiry, ordering and 1124
service system other information, refer to
P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
URETHANES FOR HEAVY LOAD URETHANES WITH COUNTERBORE HOLE
LA DD d AZ(Standard type) DÚ0.2
8 d 1Ú0.2
C
10 V
Product guide 15
L d 20 Ú0.2 10
Catalog No. D 25 L+00.5
Type D - L 30 F
40 Ú0.2
C 8-200 50
C 10-200
C 15-200 Ú0.3
C 20-200 60
C 25-200 80
C 30-500
C 40-500 Ú0.4
C 50-500 L D 100
C 60-500
C 80-500 d 2Ú0.2
C 100-500
P.1119 Shore A90 Product guide P.1119 Shore A90
Catalog No. U/Price Order Catalog No. F=LM10% F=LM15% F=LM20% D d1 d2 M L Catalog No. U/Price Order Catalog No.
d Q'ty:1~19 LA 60-500 Type D-L Q'ty:1~19 AZ 20-30
F Load F Load F Load V
Type D - L 280 mm N kgf mm N kgf mm N kgf
280
7 LA 15-200 280 2.5 3.7 5.0 25 AZ 20 - 25
8.5 LA 20-200 410
11 LA 25-200 660 3.0 883 4.5 1079 6.0 1275 24 20 11 7 M6 30 30 285 1Delivery
2,350 3.5 90 5.2 110 7.0 130 35 35
LA 30-500 4,200 1Delivery Day
14 LA 40-500 6,440 Day 4.0 6.0 8.0 40 40
9,300
LA 50-500 15,620 2.5 3.7 5.0 25 AZ 25 - 25
LA 60-500 24,370
22 LA 80-500 3.0 1177 4.5 1569 6.0 1765 29 25 11 7 M6 30 30 380
LA 100-500 3.5 120 5.2 160 7.0 180 35 35
Price 4.0 6.0 8.0 40 40 Price
3.0 2550 4.5 3040 6.0 3530 30 AZ 30 - 30
3.5 5.2 7.0 35 30 14
IVolume discount rate P.37 4.0 260 6.0 310 8.0 360 9 M8 35 35 570 IVolume discount rate P.37
Quantity 1~19 20~49 50~99 100~200 40 40 Quantity 1~19 20~49 50~199 200~400
Rate - 5% 10% 15% 3.0 4119 4.5 5099 6.0 5884 30 AZ 40 - 30 Rate - 5% 10% 15%
To be quoted on price & lead time above Max. Q'ty. 3.5 5.2 7.0 46 40 18 11 M10 35 35 710 To be quoted on price & lead time above Max. Q'ty.
4.0 420 6.0 520 8.0 600
40 40
kgf=NM0.101972
AZX(Full length specified type) D DD
d 1Ú0.2 25
Full length specified type AX DD d L 30 Ú0.2
40
8 50
10 Ú0.3
60
d 15 80
L D 20 Ú0.2 Ú0.3 Ú0.4
100
CX 25 HÚ0.5
L+00.5
30
40 Ú0.2
L 50 d 2Ú0.2
P.1119 Ú0.3
Product guide P.1119 Shore A90
60 Ú0.5
80
Ú0.4
D 100
Product guide Shore A90 Catalog No. L H
1mm increments 1mm increments
20 ~ 80 M M d1 d2 Order Catalog No. L M H
Delivery
L U/Price Q'ty:1~19 Catalog No. D L Type D 25 ~ 150 M 6 11 7 AZX 25 42 M6 15
1mm increments L10~20 L21~40 L41~60 L61~80 L81~100 L101~150 L151~200 AX 20 45 M 8 14 9
d Catalog No. D Order 25 25 ~ 200 M6 M10 18 11
90 95 110 145 180 270 350 M12 20 14
90 95 110 145 180 270 350 30 M8 M16 26 18
90 90 100 140 180 275 360
- 8 90 95 130 190 245 370 490 40 M10 3 Days
10 130 150 195 275 330 490 655 5¯H<L
CX 10~200 160 205 300 385 480 720 955 3 Days AZX 50 Express T 1,600/1Pc.
215 360 540 720 900 1,355 1,805 M12 Express A 800/1Pc. P.38
- 360 635 900 1,175 1,440 2,165 2,885 Delivery Express T 600/1Pc. 60 A flat charge of 2,160 yen for 3 pieces or more of the same size.
540 900 1,260 1,620 1,985 2,980 3,970 Express A 300/1Pc. P.38 (excluding Express T)
7 15 860 1,490 2,165 2,885 3,610 5,415 7,220 A flat charge of 810 yen for 3 pieces or more of the same size. 80 M12
1,355 2,260 3,245 4,330 5,415 8,120 10,830 (excluding Express T) M16
8.5 20 100
11 25 IVolume discount rate P.37
AX 30 Price Quantity 1~19 20~49 50~99 100~200 To be quoted on price &
14 CX 40 10% 15% lead time above Max. Q'ty.
50 Rate - 5%
Price Catalog No. D L U/Price Q'ty:1~19
L20~40 L41~60 L61~80 L81~100 L101~150 L151~200
570 665 - -
60 IVolume discount rate P.37 25 665 760 760 - - -
950 1,995 -
80 Quantity 1~19 20~49 50~99 100~200 30 1,140 855 - 2,850 -
22 1,235 1,520 4,085 -
Rate - 5% 10% 15% 40 1,615 1,995 1,330 1,520 7,030 9,025
100 2,375 3,230 9,880
To be quoted on price & lead time above Max. Q'ty. AZX 50 3,325 4,370 1,805 2,090 12,825
60 2,470 3,040
80 4,085 5,035
100 5,605 6,935
1125 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1126
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
URETHANE SHEETS URETHANE DIE PADS
UT UD
T Ú0.3 B Ú0.3
1~ 4 Ú0.4
B+100 5~10 Ú0.5
15~25 Ú1
30~50
AÚ0.3 L
A+100 T Product guide P.1119 Shore A90
P.1119
Product guide Shore A90 Catalog No. U/Price
Type A - L Q'ty:1~9
ABL Order Catalog No.
UD 75- 1000
A B Catalog No. U/Price Catalog No. 50 UD 25 - 50 250
T Type T - A Q'ty:1~9 UT 8-500 100 100 500
Order Ú1
5 UT 5 - 300 3,600 300 300 1,300 1Delivery Day
500 +5 500 2,200
6 6 - 300 4,400 25 25 800 3,500
8 8 - 300 5,800 1Delivery Day 800 0
300 300 10 10 - 300 6,300
15 - 300 9,500 1000 1000 4,300
15
50 UD 50 - 50 1,000
20 20 - 300 12,600 100 Ú1 100 1,700 Price
25 25 - 300 15,100 Price 300 300 5,200
500 +5 500 8,400
30 30 - 300 17,200 50 50 800 13,000 IVolume discount rate
1000 15,900
1 UT 1 - 500 1,800 800 0 Quantity 1~9 10~19 20~49 P.37
10%
2 2 - 500 3,400 IVolume discount rate P.37 1000 Rate - 5% 50~100
15%
3 3 - 500 5,200 50~100
Quantity 1~9 10~19 20~49 15% 50 UD 75 - 50 1,300 To be quoted on price & lead time above Max. Q'ty.
4 - 500 10% 100 Ú1 100 2,600
4 6,700 Rate - 5%
5 5 - 500 8,400 To be quoted on price & lead time above Max. Q'ty. 300 300 7,500
500 +5 500 12,600
6 6 - 500 10,100 75 50 800 19,000
8 8 - 500 13,400
500 500 800 0
10 10 - 500 15,900 1000 1000 24,000
15 15 - 500 23,900
20 20 - 500 31,800 UDH(Full length specified type)
25 25 - 500 39,800 L
25
30 30 - 500 47,700 ~~~ +1
200 0
50 50 - 500 79,500 201
+2
B Ú0.3 500 0
501
UTH(Size specified type) +3
1000 0
T Ú0.3 AÚ0.3 L
1~ 4 Ú0.4
+2 5~10 Ú0.5 Product guide P.1119 Shore A90
0 15~25 Ú1
30~50
B
A B Catalog No. L U/Price Order Catalog No. L
Type A 1mm increments Q'ty:1~9
UDH 50 355
25 ~ 50 300
A+02 51 ~ 100 600
T 25 25 UDH 25 101 ~ 300 1,560 3Delivery Days
301 ~ 500 2,640
Product guide P.1119 Shore A90 501 ~ 800 4,200 Express A 800/1Pc. P.38
801 ~1000 5,160
25 ~ 50 1,200 A flat charge of 2,160 yen for 3 pieces or more of the same size.
51 ~ 100 2,040
Catalog No. 1mm increments Catalog No. 1mm increments Order Catalog No. A B 50 50 UDH 50 101 ~ 300 6,240 Price
UTH 8 351 200 301 ~ 500 10,080
Type T A B Type T A B
1 10 501 ~ 800 15,600
801 ~1000 19,080 IVolume discount rate P.37
2 15 Delivery 3 Days 25 ~ 50 1,560 Quantity 1~9 10~19 20~49 50~100
51 ~ 100 3,120 Rate - 5%
3 20 10% 15%
4 20~500 20~500 25 20~500 20~500
UTH UTH Express A 800/1Pc. P.38 75 50 UDH 75 101 ~ 300 9,000 To be quoted on price & lead time above Max. Q'ty.
301 ~ 500 15,120
A flat charge of 2,160 yen for 3 pieces or more of the same size.
5 30 501 ~ 800 22,800
6 40 801 ~1000 28,800
8 50 Price P.1129
1127 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1128
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
URETHANE SHEETS
-PRICE-
IVolume discount rate P.37
Price Quantity 1~9 10~19 20~49 50~100
10% 15%
Rate - 5% To be quoted on price & lead time above Max. Q'ty.
IUTH U/Price(Q'ty:1~9), Dimension A 20~300 IUTH U/Price(Q'ty:1~9), Dimension A 301~500
A T1234568 ~~~~A T 10 15 20 25 30 40 50A T1234568 A T 10 15 20 25 30 40 50
B ~~~~B B B
20~100 1,400 1,400 1,740 2,270 2,630 3,090 4,040
20~100 1,400 1,400 1,400 1,400 1,400 1,400 1,400 ~~~~~20~100 1,400 2,480 3,120 3,750 4,590 6,120 7,500 20~100 4,730 6,460 8,190 10,240 12,290 17,220 19,950
101~150 1,400 1,400 1,400 1,400 1,400 1,400 1,980 ~~~~~ 101~150 2,430 3,450 4,320 5,290 6,480 8,820 10,580 101~150 1,400 1,740 2,510 3,220 3,470 4,070 5,300 101~150 6,150 8,270 10,710 13,390 16,070 22,050 25,990
151~200 1,400 1,400 1,400 1,400 1,400 1,980 2,550 151~200 3,060 4,320 5,400 6,750 8,100 11,280 13,500 151~200 1,400 2,230 3,150 4,040 3,990 4,790 6,220 151~200 7,140 9,770 13,020 16,280 18,900 26,040 30,450
20 201~250 1,400 1,400 1,400 1,400 2,030 2,390 3,060 20 201~250 3,680 5,070 6,450 7,880 9,680 13,500 15,750 301 201~250 1,400 2,580 3,710 4,730 4,470 5,200 6,930 301 201~250 8,140 11,420 14,700 17,720 22,840 30,450 35,440
251~300 1,400 1,400 1,400 1,980 2,390 2,760 3,600 251~300 4,230 5,810 7,380 9,230 11,070 15,480 18,000 251~300 1,740 2,970 4,260 5,420 5,040 6,050 8,070 251~300 9,450 13,230 17,640 21,270 26,460 34,020 40,950
100 301~350 1,400 1,400 1,740 2,270 2,630 3,090 4,040 100 301~350 4,730 6,460 8,190 10,240 12,290 17,220 19,950 350 301~350 1,780 3,240 4,730 6,000 5,150 7,060 9,410 350 301~350 11,030 14,890 19,850 23,890 29,770 38,220 47,780
351~400 1,400 1,400 1,950 2,550 2,880 3,460 4,520 351~400 5,160 7,020 8,880 11,100 13,680 18,720 21,600 351~400 1,940 3,620 5,170 6,560 6,720 7,820 10,420 351~400 12,600 17,010 22,680 27,300 34,020 42,000 50,400
401~450 1,400 1,400 2,190 2,810 3,110 3,650 4,860 401~450 5,540 7,500 9,450 12,150 14,990 20,520 23,630 401~450 2,080 3,780 5,390 7,000 7,560 8,790 11,720 401~450 14,180 19,140 24,570 30,720 36,860 47,250 54,340
451~500 1,400 1,400 2,390 3,060 3,380 3,960 5,160 451~500 6,450 7,880 10,200 13,130 15,750 21,600 24,750 451~500 2,210 3,890 5,670 7,350 8,140 9,770 13,020 451~500 15,230 20,480 26,250 32,820 39,380 50,400 60,380
20~100 1,400 1,400 1,400 1,400 1,400 1,400 1,980 20~100 2,430 3,450 4,320 5,290 6,480 8,820 10,580 20~100 1,400 1,400 1,950 2,550 2,880 3,460 4,520 20~100 5,160 7,020 8,880 11,100 13,680 18,720 21,600
101~150 1,400 1,400 1,400 1,400 1,830 2,190 2,810 101~150 3,380 4,760 6,080 7,430 8,910 12,420 14,520 101~150 1,400 1,950 2,760 3,530 3,690 4,430 5,760 101~150 6,660 9,180 11,520 14,850 17,280 24,480 27,900
151~200 1,400 1,400 1,400 1,980 2,390 2,760 3,600 151~200 4,230 5,810 7,380 9,230 11,070 15,480 18,000 151~200 1,400 2,450 3,530 4,420 4,200 5,040 6,720 151~200 7,680 10,440 14,400 17,400 20,880 28,800 33,600
101 201~250 1,400 1,400 1,860 2,390 2,820 3,240 4,230 101 201~250 4,950 6,590 8,550 10,690 13,170 18,000 20,820 351 201~250 1,400 2,820 4,050 5,160 4,950 5,760 7,680 351 201~250 9,600 12,600 16,200 20,250 25,200 33,600 39,000
251~300 1,400 1,400 2,190 2,810 3,110 3,650 4,860 251~300 5,540 7,500 9,450 12,150 14,990 20,520 23,630 251~300 1,770 3,240 4,650 5,910 5,760 6,920 9,220 251~300 10,800 14,580 20,160 23,400 29,160 37,440 45,000
150 301~350 1,400 1,740 2,510 3,220 3,470 4,070 5,300 150 301~350 6,150 8,270 10,710 13,390 16,070 22,050 25,990 400 301~350 1,940 3,620 5,170 6,560 6,720 7,820 10,420 400 301~350 12,600 17,010 22,680 27,300 34,020 42,000 50,400
351~400 1,400 1,950 2,760 3,530 3,690 4,430 5,760 351~400 6,660 9,180 11,520 14,850 17,280 24,480 27,900 351~400 2,080 3,820 5,480 7,110 7,680 8,930 11,910 351~400 14,400 19,440 24,960 31,200 37,440 48,000 55,200
401~450 1,400 2,150 3,040 3,890 3,950 4,740 6,160 401~450 7,090 9,420 12,560 15,700 18,840 25,110 29,370 401~450 2,270 4,000 5,670 7,560 8,370 10,050 13,400 401~450 15,660 21,060 27,000 33,750 40,500 52,000 62,100
451~500 1,400 2,300 3,310 4,230 4,170 5,000 6,480 451~500 7,430 10,130 13,500 16,880 19,580 27,900 31,500 451~500 2,340 4,080 5,940 7,920 9,300 11,160 14,400 451~500 17,400 22,500 30,000 36,000 45,000 55,200 69,000
20~100 1,400 1,400 1,400 1,400 1,400 1,980 2,550 20~100 3,060 4,320 5,400 6,750 8,100 11,280 13,500 20~100 1,400 1,400 2,190 2,810 3,110 3,650 4,860 20~100 5,540 7,500 9,450 12,150 14,990 20,520 23,630
101~150 1,400 1,400 1,400 1,980 2,390 2,760 3,600 101~150 4,230 5,810 7,380 9,230 11,070 15,480 18,000 101~150 1,400 2,150 3,040 3,890 3,950 4,740 6,160 101~150 7,090 9,420 12,560 15,700 18,840 25,110 29,370
151~200 1,400 1,400 1,950 2,550 2,880 3,460 4,520 151~200 5,160 7,020 8,880 11,100 13,680 18,720 21,600 151~200 1,400 2,650 3,810 4,860 4,460 5,190 7,130 151~200 8,370 11,340 15,120 18,230 22,680 30,240 36,450
151 201~250 1,400 1,400 2,390 3,060 3,380 3,960 5,160 151 201~250 6,450 7,880 10,200 13,130 15,750 21,600 24,750 401 201~250 1,740 3,110 4,460 5,670 5,400 6,480 8,640 401 201~250 10,130 13,670 18,230 22,790 27,340 36,450 43,880
251~300 1,400 1,950 2,760 3,530 3,690 4,430 5,760 251~300 6,660 9,180 11,520 14,850 17,280 24,480 27,900 251~300 1,920 3,490 4,990 6,320 6,480 7,540 10,050 251~300 12,150 16,410 21,870 26,330 32,810 41,000 50,700
200 301~350 1,400 2,230 3,150 4,040 3,990 4,790 6,220 200 301~350 7,140 9,770 13,020 16,280 18,900 26,040 30,450 450 301~350 2,080 3,780 5,390 7,000 7,560 8,790 11,720 450 301~350 14,180 19,410 24,570 30,720 36,860 47,250 54,340
351~400 1,400 2,450 3,530 4,420 4,200 5,040 6,720 351~400 7,680 10,440 14,400 17,400 20,880 28,800 33,600 351~400 2,270 4,000 5,670 7,560 8,370 10,050 13,400 351~400 15,660 21,060 27,000 33,750 40,500 52,000 62,100
401~450 1,400 2,650 3,810 4,860 4,460 5,190 7,130 401~450 8,370 11,340 15,120 18,230 22,680 30,240 36,450 401~450 2,370 4,140 6,020 8,020 9,420 11,300 14,580 401~450 17,620 22,790 30,380 36,450 45,570 55,890 69,870
451~500 1,400 2,820 4,050 5,160 4,950 5,760 7,680 451~500 9,600 12,600 16,200 20,250 25,200 33,600 39,000 451~500 2,500 4,320 6,480 8,100 10,470 12,560 16,200 451~500 19,580 25,320 32,400 40,500 48,600 62,100 77,630
20~100 1,400 1,400 1,400 1,400 2,030 2,390 3,060 20~100 3,680 5,070 6,450 7,880 9,680 13,500 15,750 20~100 1,400 1,400 2,390 3,060 3,380 3,960 5,160 20~100 6,450 7,880 10,200 13,130 15,750 21,600 24,750
101~150 1,400 1,400 1,860 2,390 2,820 3,240 4,230 101~150 4,950 6,590 8,550 10,690 13,170 18,000 20,820 101~150 1,400 2,300 3,310 4,230 4,170 5,000 6,480 101~150 7,430 10,130 13,500 16,880 19,580 27,900 31,500
151~200 1,400 1,400 2,390 3,060 3,830 3,960 5,160 151~200 6,450 7,880 10,200 13,130 15,750 21,600 24,750 151~200 1,400 2,820 4,050 5,160 4,950 5,760 7,680 151~200 9,600 12,600 16,200 20,250 25,200 33,600 39,000
201 201~250 1,400 2,030 2,870 3,680 3,750 4,500 5,850 201 201~250 6,750 9,250 12,000 15,470 17,440 24,750 28,130 451 201~250 1,820 3,300 4,730 6,000 6,000 7,200 9,600 451 201~250 11,250 15,190 20,250 24,380 30,380 39,000 48,750
251~300 1,400 2,300 3,310 4,230 4,170 5,000 6,480 251~300 7,430 10,130 13,500 16,880 19,580 27,900 31,500 251~300 2,030 3,690 5,270 6,840 7,200 8,370 11,160 251~300 13,500 18,230 23,400 29,250 35,100 45,000 51,750
250 301~350 1,400 2,580 3,710 4,730 4,470 5,200 6,930 250 301~350 8,140 11,420 14,700 17,720 22,840 30,450 35,440 500 301~350 2,210 3,890 5,670 7,350 8,140 9,770 13,020 500 301~350 15,230 20,480 26,250 32,820 39,380 50,400 60,380
351~400 1,400 2,820 4,050 5,160 4,950 5,760 7,680 351~400 9,600 12,600 16,200 20,250 25,200 33,600 39,000 351~400 2,340 4,080 5,940 7,920 9,300 11,160 14,400 351~400 17,400 22,500 30,000 36,000 45,000 55,200 69,000
401~450 1,740 3,100 4,460 5,670 5,400 6,480 8,640 401~450 10,130 13,670 18,230 22,790 27,340 36,450 43,880 401~450 2,500 4,320 6,480 8,100 10,470 12,560 16,200 401~450 19,580 25,320 32,400 40,500 48,600 62,100 77,630
451~500 1,820 3,300 4,730 6,000 6,000 7,200 9,600 451~500 11,250 15,190 20,250 24,380 30,380 39,000 48,750 451~500 2,670 4,350 6,750 9,000 11,250 13,500 18,000 451~500 22,500 27,000 34,500 43,130 51,750 69,000 86,250
20~100 1,400 1,400 1,400 1,980 2,390 2,760 3,600 20~100 4,230 5,810 7,380 9,230 11,070 15,480 18,000
101~150 1,400 1,400 2,190 2,810 3,110 3,650 4,860 101~150 5,540 7,500 9,450 12,150 14,990 20,520 23,630
151~200 1,400 1,950 2,760 3,530 3,690 4,430 5,760 151~200 6,660 9,180 11,520 14,850 17,280 24,480 27,900
251 201~250 1,400 2,300 3,310 4,230 4,170 5,000 6,480 251 201~250 7,430 10,130 13,500 16,880 19,580 27,900 31,500
251~300 1,400 2,650 3,810 4,860 4,460 5,350 7,130 251~300 8,370 11,340 15,120 18,230 22,680 30,240 36,450
300 301~350 1,740 2,970 4,260 5,420 5,040 6,050 8,070 300 301~350 9,450 13,230 17,640 21,270 26,460 34,020 40,950
351~400 1,770 3,240 4,650 5,910 5,760 6,920 9,220 351~400 10,800 14,580 20,160 23,400 29,160 37,440 45,000
401~450 1,920 3,490 4,990 6,320 6,480 7,540 10,050 401~450 12,150 16,410 21,870 26,330 32,810 41,000 50,700
451~500 2,030 3,690 5,270 6,840 7,200 8,370 11,160 451~500 13,500 18,230 23,400 29,250 35,100 45,000 51,750
1129 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1130
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
ECONOMY URETHANES
AE(Standard type) D N{kgf} DD d L LAE DD d
V CE 8
d 15 10
15
20 d 20 Ú0.2
D 25
25 Ú0.2 Ú0.3 30 Ú0.2
40
L 30 Ú0.2 L 50
F
40 Ú0.3
60
50 Ú0.5
Ú0.3
60
L D
Shore A90
Product guide P.1119 Products information P.1137 Shore A90 Product guide P.1119
F=LM15% F=LM20% F=LM25% d Catalog No. U/Price d Catalog No. Catalog No. U/Price Order Catalog No.
Type D - L Type D - L Q'ty:1~19 LAE 30-500
F Load F Load F Load V Type D - L Q'ty:1~19 -
mm N{kgf} mm N{kgf} mm N{kgf} 18 - - CE 8-200 210
24 AE 15 - 25 35 - CE 10-200 210 Delivery 3 Days
3.8 5 6.3 30 35 7 LAE 15-200 CE 15-200 210 Price
4.5 539 6 735 7.5 932 30 35 8.5 LAE 20-200 CE 20-200 320 Express T 400/1Pc.
5.3 { 55} 7 { 75} 8.8 { 95} 7 35 11 LAE 25-200 CE 25-200 500 Express A 200/1Pc. P.38
6 8 10 37 35 55 LAE 30-500 CE 30-500 1,820 A flat charge of 540 yen for 3 pieces or more of the same size
3.8 5 6.3 40 55 14 LAE 40-500 CE 40-500 3,250 (excluding Express T).
4.5 1079 6 1373 7.5 1667 48 55 LAE 50-500 CE 50-500 4,990
5.3 { 110} 7 { 140} 8.8 { 170} 60 AE 20 - 25 55 LAE 60-500 CE 60-500 7,190 IVolume discount rate P.37
6 8 10 72 30 100
3.8 5 6.3 100 Quantity 1~19 20~49 50~99 100~200
4.5 6 7.5 8.5 100 Rate - 5%
5.3 1569 7 2059 8.8 2550 35 100 10% 15%
6 { 160} 8 { 210} 10 { 260} 40 100
6.8 9 11.3 100 To be quoted on price & lead time above Max. Q'ty.
7.5 10 12.5 AE 25 - 25 105
4.5 6 7.5 30 120 Full length specified type AEX DD d L
5.3 7 8.8 35 130 CEX
6 8 10 150 8
6.8 2452 9 2844 11 160
7.5 { 250} 10 { 290} 3334 40 180 10
8.3 11 11.3 45 200
9 12 12.5 { 340} 50 230 d 15
6 4315 8 5099 13.8 300
7.5 10 15 AE 30 - 30 360 L 20 Ú0.2 Ú0.3
9 { 440} 12 { 520} 10 5982 35 480 D 25
7.5 7355 10 8728 12.5 40 570
9 12 15 { 610} 770 30 Ú0.2
12 { 750} 16 { 890} 12.5 10297 14 45 690
7.5 12356 10 14318 15 50 820 40
9 12 20 {1050} 55 1,100
12 {1260} 16 {1460} 12.5 16769 60 50 Ú0.5
15 Ú0.3
20 {1710} AE 40 - 40
14 50 60
60 L D
AE 50 - 50
14 60 Product guide P.1119 Shore A90
80 d Catalog No. D L U/Price Q'ty:1~19 Order Catalog No. D L
AE 60 - 50 1mm increments L10~20 L21~40 L41~60 L61~80 L81~100 L101~150 L151~200 AEX 20 52
14 60
- 8 75 80 95 125 155 230 300 3 Days
80 10 75 80 95 125 155 230 300
CEX 15 80 80 95 130 160 250 330 Express T 400/1Pc.
kgf=NM0.101972 20 80 90 120 170 220 330 440 Delivery Express A 200/1Pc. P.38
- 25 10~200 120 140 180 250 300 440 590 Price A flat charge of 540 yen for 3 pieces or more of the same size
Order Catalog No. F F˘10 7 30 150 190 270 350 440 650 860 (excluding Express T).
AE 15-25 8.5 40
Example 50
11 AEX 60
Delivery 3 Days Express T 400/1Pc. P.38
Price Express A 200/1Pc. CEX
A flat charge of 540 yen for 3 pieces or more of the same size 14 200 330 490 650 810 1,220 1,620
(excluding Express T). SGA P.1099 330 570 810 1,060 1,290 1,940 2,590 IVolume discount rate P.37
IVolume discount rate P.37 Quantity 1~19 20~49 50~99 100~200
10% 15%
Quantity 1~19 20~49 50~99 100~400 490 810 1,130 1,460 1,780 2,670 3,560 Rate - 5%
Rate - 5%
10% 15% To be quoted on price & lead time above Max. Q'ty.
To be quoted on price & lead time above Max. Q'ty.
1131 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1132
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
HIGH DEFLECTION TYPE URETHANE FOAM(POROUS) URETHANES
-LOW REPULSION TYPE-
PA(Standard type) D Ú1.4 N{kgf} AN(Standard type) D N{kgf} DD d L
d Ú0.8 V d V
20
25 Ú0.2 Ú0.3
30 Ú0.2
L Ú1.6
F 40
L 50 Ú0.5
F Ú0.3
60
Product guide P.1119 Product guide P.1119 Shore A70
Products information P.1137
Products information P.1137
Although urethane springs are discolored when exposed to ultraviolet ray(s including sunlight), it will not affect the usage. F=LM15% F=LM20% F=LM25% d Catalog No. U/Price Catalog No.
Type D - L AN 25-40
Load Load Load Q'ty:1~19 Order
VF F F AN 20-25
mm N{kgf} mm N{kgf} mm N{kgf} 30 160
F=LM20% F=LM30% F=LM40% Catalog No. U/Price Catalog No. 160
d Type D - L Q'ty:1~19 Order PA 50-50 3.75 5 6.25 8.5 35 170
Load Load F Load 40 170
N{kgf}
F F
Vmm
N{kgf} mm N{kgf} mm 4.5 343 6 451 7.5 617
5.25 { 35} 7 { 46} 8.75{ 63} 24
6 { 981 9 1177 12 1471 36 PA 30 - 30 150 6 8 10 1Delivery Day
8 100} 12 { 120} 16 { 150} 40 190
340
8 1961 12 2452 16 3040 PA 40 - 40 430 1Delivery Day 3.75 5 6.25 AN 25-25 250
10 15 20 48 30 250
12 { 200} 18 { 250} 24 { 310} 50 520 4.5 6 7.5 35 250
60 5.25 470 7 686 8.75 912 30 40 300
6 { 48} 8 { 70}10 { 93} 45 300
8 12 16 PA 50 - 40 560 6.75 9 11.3 11 50 300 Price
10 3481 15 4413 20 5541 60 14 50 690
12 { 355} 18 { 450} 24 { 565} 820 Price 7.5 10 12.5
16 24 32 60 1,120
80 IVolume discount rate P.37
990
10 15 20 PA 60 - 50 1,180 IVolume discount rate P.37 4.5 6 7.5 AN 30-30 330 Quantity 1~19 20~49 50~199 200~400
60 1,580 5.25 7 8.75 35 330 Rate -
12 4609 18 5737 24 7257 80 1,980 5% 10% 15%
72
100 Quantity 1~19 20~49 50~199 200~400 6 666 8 941 10 1245 40 440 To be quoted on price & lead time above Max. Q'ty.
Rate - 45 440
16 { 470} 24 { 585} 32 { 740} 5% 10% 15% 6.75 9 11.3 37 14 50 460
20 30 40 To be quoted on price & lead time above Max. Q'ty. 7.5 { 68} 10 { 96}12.5 {127}
12 18 24 PA 80 - 60 2,100 8.3 11 13.8 55 500
10787 13729 80
16 8532 24 {1100} 32 {1400} 96 2,800 9 12 15 60 550
20 { 870} 30 40 100 3,490
130 4,550 6 8 1914 10 AN 40-40 580
26 39 52 7.5 1343 10 12.5 2549 48 14 50 850
60 950
16 24 32 PA 100 - 80 4,370 9 {137} 12 {195}15 {260}
22 100 5,460
20 13925 30 17652 40 21771 7.5 2081 10 2983 12.5 4028 14 AN 50-50 1,400
24 {1420} 36 {1800} 48 120 120 6,330 9 12 15 59 60 1,600
8,540 12 {212} 16 {304}20 {410} 80 1,900
32 48 64 {2220} 160
16 24 32 PA 120 - 80 6,070 7.5 3089 10 4481 12.5 5962 AN 60-50 1,900
24909 30793 100 7,590 60 2,250
20 19907 30 {2540} 40 144 9,100 9 {315} 12 {457}2150 71 14 80 2,600
24 {2030} 36 48 120 12,000 12 16 {608}
{3140} 160
32 48 64
kgf=NM0.101972 kgf=NM0.101972
LAN K LAN D D d
ANX(Full length Specified) K CNN 20
PLA
25 Ú0.2
30 Ú0.2
40
L d
D 50
60 Ú0.3
D
CNN Shore A70 K ANX DD d L
CNX(Full length Specified) K CNX
d Ú0.8 20
DÚ1.4 Product guide P.1119
25 Ú0.2 Ú0.3
30
LÚ2.0 Ú0.2
L 40
50 Ú0.3 Ú0.5
60
Product guide P.1119 Please use by cutting. P.1137 d Catalog No. U/Price d Catalog No. D L U/Price Q'ty:1~19
Although urethane springs are discolored when exposed to ultraviolet rays(including sunlight), it will not affect the usage. 1mm increments L10~20 L21~40 L41~60 L61~80 L81~100 L101~150 L151~200
Type D - L Q'ty:1~19
Catalog No. U/Price Catalog No. 1Delivery 8.5 20-200 700 8.5 20 150 170 230 310 400 600 780
Type D - L Q'ty:1~19 PLA 80-200
d PLA 30-200 Order Day 11 LAN 25-200 940 11 ANX 25 230 250 320 440 530 780 1,040
14 1,040 14 CNN 30-200 1,390 14 CNX 270 330 480 620 770 1,160 1,540
22 PLA 40-200 1,860 40-300 3,910 30 10~200 350 580 870 1,160 1,450 2,170 2,890
PLA 50-200 2,860 50-300 6,240 40 580 1,020 1,450 1,880 2,310 3,470 4,620
1133 PLA 60-200 4,110
PLA 80-200 6,920 50
10,800
PLA 100-200 15,600 60-300 8,580 60 870 1,450 2,020 2,600 3,180 4,770 6,360
PLA 120-200
Please use by cutting. IVolume discount rate P.37
Price Quantity 1~19 20~49 50~199 200~400 Catalog No. D L LAN 1 Day
Rate - Days
5% 10% 15% Order LAN 60 300 Delivery CNN
Price ANX 20 150
To be quoted on price & lead time above Max. Q'ty.
IVolume discount rate P.37 ANX 3 Express T 600/1Pc. P.38
CNX Express A 300/1Pc.
Quantity 1~19 20~49 50~99 100~200 A flat charge of 810 yen for 3 pieces or more of the same size 1134
Rate - 5% 10% 15% (excluding Express T).
To be quoted on price & lead time above Max. Q'ty.
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
URETHANES WITH COUNTERBORE HOLE URETHANE SHEETS/URETHANE DIE PADS
-LOW REPULSION TYPE- -LOW REPULSION TYPE-
AZN(Standard type) DÚ0.2 UTN(Urethane sheet) T
d 1Ú0.2 5 Ú0.4
10
V 15
20 Ú0.5
10 B+010 25
L+00.5 30 Ú1
F
+10 T
A0
d 2Ú0.2
Product guide P.1119 Shore A70 Product guide P.1119 Shore A70
F=LM10% F=LM15% F=LM20% D d1 d2 M Catalog No. U/Price Catalog No. Catalog No. U/Price Catalog No.
L Type D - L Q'ty:1~19 AZN 25-30 AB T Order UTN 25 - 250
F Load F Load F Load Order 250 250
Type T - A Q'ty:1~9
Vmm N{kgf} mm N{kgf} mm N{kgf}
2.5 3.7 5.0 25 AZN25 - 25 730 5 UTN 5 - 250 6,800
3.0 304 4.5 442 6.0 647 30 30 730 1 10 10 - 250 13,500
3.5 {31} 5.2 {45} 7.0 {66} 29 25 11 7 M6 35 35 730
Delivery Day 1Delivery Day
4.0 6.0 8.0 40 40 730 15 15 - 250 19,700
3.0 4.5 6.0 30 AZN30 - 30 850 20 20 - 250 26,400
850
3.5 362 5.2 627 7.0 892 35 30 14 9 M8 35 35 850 25 25 - 250 32,900
{37} {64} {91}
4.0 6.0 8.0 40 40 Price 30 39,300 Price
30 - 250
3.0 4.5 6.0 30 AZN40 - 30 1,220
735 1274 1814 IVolume discount rate
3.5 {75} 5.2 {130} 7.0 {185} 46 40 18 11 M10 35 35 1,220 P.37 IVolume discount rate P.37
4.0 6.0 8.0 40 40 1,220 Quantity 1~19 20~49 50~199 200~400 Quantity 1~9 10~19 20~49 50~100
Rate -
5% 10% 15% Rate - 5% 10% 15%
3.0 4.5 6.0 30 AZN50 - 30 1,600 To be quoted on price & lead time above Max. Q'ty. To be quoted on price & lead time above Max. Q'ty.
3.5 1117 5.2 1971 7.0 2824 57 50 35 35 1,600
4.0 {114} 6.0 {201} 8.0 {288} 20 14 M12 40 1,700
40
5.0 7.5 10.0 50 50 1,700
kgf=NM0.101972
AZNX(Full length D DD UDN(Urethane die pad)
d 1Ú0.2 25
specified type) 30 Ú0.2
40
50 Ú0.3 B Ú0.3
HÚ0.5 AÚ0.3 L
L+00.5
d 2Ú0.2
Product guide P.1119 Shore A70 Product guide P.1119 Shore A70
Catalog No. L H Order Catalog No. L M H ABL Catalog No. U/Price Catalog No.
1mm increments 1mm increments 15 Type A - L Q'ty:1~9 UDN 25 - 300
Type D M Order
20 ~ 60 5¯H<L
M6 AZNX 25 42 M6
25 ~ 100 M8
25 50 Ú1 UDN 25 - 50 520
M10 100 100 1,040
30 M12 Delivery 3 Days Express T 600/1Pc. P.38 25 25 1Delivery Day
40 Price Express A 300/1Pc.
AZNX +5
A flat charge of 810 yen for 3 pieces or more 300 0 300 2,770
50 of the same siz(e excluding Express T). 50 Ú1 UDN 50 - 50 2,080
3,540
IVolume discount rate P.37 50 50 100 100
Deta M M6 M8 M10 M12 Quantity 1~19 20~49 50~99 100~200 +5 Price
d1 11 14 18 20 Rate - 5% 0
d2 7 9 11 14 10% 15% 300 300 10,810
To be quoted on price & lead time above Max. Q'ty. IVolume discount rate
P.37
L U/Price Q'ty:1~19 Quantity 1~9 10~19 20~49 50~100
D Rate - 5%
L20~40 L41~60 L61~80 L81~100 10% 15%
25 870 -
30 1,010 - - To be quoted on price & lead time above Max. Q'ty.
40 1,000
50 1,450 1,160 - 2,310
1,880 3,190
1,740 2,020
2,310 2,750
1135 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1136
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
PRODUCTS INFORMATION PRODUCTS INFORMATION
URETHANE LOAD / DEFLECTION GRAPH DURABILITY / PERMANENT STRAIN OF URETHANE
IHeavy load type urethane(Shore A90) IHeavy load type urethane(Shore A90)
F50CF60 F80CF100
EX type EX type
Load Load Load Load
N kgf N EX6080
kgf (F60M80L)Compression 30% 80SPM not lubricated EX100100
EX6060 (F100M100L)Compression 30% 80SPM not lubricated
6080 iDnicrmeeanssieonal
2,000 EX6206 19613
1,800 6208
17652 7000 EX 10080 68647 iDnicrmeeanssieonal 106
100100 105 MAX Durability
100120 Variation in height 104 mm Diametric deformation
Permanent strain% 103 Axial deformation
1,600 EX5060 15691 6000 EX 10208 58840 MAX Durability 102
5080 mm 101 Variation in height
1,400 EX5146 13729 5000 102010 67 100 90 10 Permanent strain%
102012 66 99 91 9
5148 EX 8080 49033 65 70 12.50 98 92 8
64 71 11.25 97 93 7
1,200 11768 80100 63 72 10.00 96 94 6
62 73 8.75 95 95 5
1,000 9807 4000 39227 61 74 7.50 94 96 4
60 75 6.25 93 97 3
800 7845 3000 EX 8208 59 76 5.00 Diametric deformation 92 98 2
82010 29420 58 77 3.75 Axial deformation 91 99 1
57 78 2.50 90 100
600 5884 2000 19613 56 79 1.25
55 80
400 3923 1000 9807
200 1961
0 5 10 15 20 25 30 % 0 5 10 15 20 25 30 %
Deflection
ACAE type Deflection
kgf=NM0.101972
F15 ~ F25 F30CF40 F50CF60 F80CF100 0 2 4 6 8 10 15 20 30 40 100 120 0 2 4 6 8 10 15 20 30 40 100 120
’M10 3 Stroke» ’M10 3 Stroke»
Load Load Load Load Load Load 5000 Load
A100- 80
kgf N kgf N kgf N Load 100-100 N ACAE type
A60-50 19613 kgf 100-120
2000 A60-80CAE60-80 ( Atype, AEtype ) A100-100
(F100M100L)Compression 25% 45SPM not lubricated
A40-40 6865 1800 60-60 17652 4000 39227 (F60M80L)Compression 25% 98SPM not lubricated
40-50 60-80
700
AE60-50
40-60 60-60
1600 60-80 15691 iDnicrmeeanssieonal iDnicrmeeanssieonal
A25-30 AE40-40
300 25-40 2942 600 40-50 5884 Variation in height
200 500 Permanent strain%
25-50 400 40-60 1400 13729 3000 A80- 60 29420 Durability MAX Durability
1200 11768 80- 80 MAX 113 mm
AE25-30 4903 1000 A50-50 80-100 mm
25-40 50-60 19613
25-50 50-80 71 112 Variation in height
70 Permanent strain%
A20-25 A30-40 69 72 10 111
30-50 68 73 9
20-30 1961 30-60 3923 AE50-50 9807 67 74 8 110
20-40 50-60 66 74 7
50-80 7845 2000 65 75 6 Diametric deformation
AE20-25 300 AE30-40 800 64 76 5 Axial deformation 109 90 10 Diametric deformation
20-30 30-50 2942 63 77 4 Axial deformation
20-35 30-60 62 78 3 108 91 9
61 78 2
A15-25 600 5884 60 80 1 107 92 8
15-30
100 15-40 981 200 1961 106 93 7
400
AE15-25 3923 1000 9807 105 94 6
15-30 1961
15-35 100 981 200 104 95 5
103 96 4
0 5 10 15 20 25 30 % 0 5 10 15 20 25 30 % 0 5 10 15 20 25 30 % 0 5 10 15 20 25 30 % 102 97 3
Deflection Deflection Deflection Deflection 101 98 2
kgf=NM0.101972
100 99 1
IHigh deflection type urethane foam 100
PA type F30CF40 Load F50CF60 Load F80 ~F120 0 2 4 6 8 10 15 20 30 40 100 120 0 2 4 6 8 10 15 20 30 40 100 120
Load kgf ’M10 3 Stroke» ’M10 3 Stroke»
Load PA60-50 N Load Load
N 1000 60-60 9807 kgf N
kgf
3923 900 60-80
PA40-40 PA120- 80 IHigh deflection type urethane foam
120-100
400 40-50 8826 4000 120-120 39227
40-60
Operation Deflection=LM10% Deflection=LM20% Deflection=LM30% Deflection=LM40% Permanent
800 7845 PA type Load Deflection Load Deflection Load Deflection Load L1 d strain
Deflection N{kgf} mm N{kgf} mm N{kgf} mm N{kgf} mm
PA50-40 Change in load and full length frequency mm 101.1 -
50-50 by operation frequency 104.9 4.2
300 2942 700 50-60 6865 3000 29420 First time 9611 {980} 13925 {1420} 17750 {1810} 22065 {2250} 120.0 105.8 6.7
PA100- 80 d L1 106.7 7.5
100-100 106.7 7.8
600 5884 100-120 10,000 times 3138 {320} 7845 {800} 10787 {1100} 16181 {1650} 115.8 106.7 8.0
200 PA30-30 1961 500 4903 2000 PA80- 60 19613 50,000 times 12 1961 {200} 24 6423 {655} 36 9512 {970} 48 14612 {1490} 113.3
3923 80- 80 100,000 times 1569 {160} 5688 {580} 8973 {915} 14024 {1430} 112.5
30-40 80-100
400 200,000 times 1373 {140} 5492 {560} 8826 {900} 13925 {1420} 112.2
300 2942 300,000 times 1177 {120} 5296 {540} 8777 {895} 13827 {1410} 112.0
100 981 1000 9807
200 1961 Load Load
kgf N
Initial load
100 981
0 10 20 30 40 50% Deflection 0 10 20 30 40 50% Deflection 0 10 20 30 40 50% Deflection 2000 19613
kgf=NM0.101972
ILow repulsion urethane(Shore A70)F20 F25CF30
F40CF50
AN type Load Load Load Load Load Load 10,000 times
kgf N kgf N kgf
80 450 AN50-50 N 50,000 times
785 170 1667 AN50-80 100,000 times
70 400 4413 1500 200,000 times 14710
AN30-30 1000 300,000 times 9807
60 AN20-25 686 150 AN30-50 1471 3923
AN20-40 130
1275 350 3432
588
AN25-25 AN40-40
AN25-50 1079 AN40-60 2942
50 490 110 300
40 392 90 883 250 2452
30 294 70 686 200 1961 500 4903
20 196 50 490 150 1471
10 98 30 294 100 981
0 10 15 20 25 30% Deflection 0 10 15 20 25 30% Deflection 0 10 15 20 25 30% Deflection 0 10 20 30 40 50
kgf=NM0.101972 Deflection in mm(percent)
1137 1138
12(10%) 24(20%) 36(30%) 48(40%)
kgf=NM0.101972
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
PRODUCTS INFORMATION
CALCULATIONS OF URETHANE LOAD CHARACTERISTICS
If urethane is used as a pressure medium, it is extremely important to know how much deflection will be caused at how much load. Especially, in (Fig. 1) Example 1
limited space setting, it is necessary to design a die appropriate for the conditions in consideration with load and deformation.The shape coefficient Suppose the length L be 100mm, the width W 80mm and the height H 30mm. How much force is necessary in this case to cause a 5mm deformation in the
and elastic modulus are necessary for determining the load and the amount of deflection. urethane's thickness(? Conditions:Heavy load urethane M is used and it is in the non-lubricated state.)(1cm=10mm)
A urethane spring, regardless of its shape, has a characteristic that it bulges on both sides when load is applied.This does not change its overall First, consider the shape coefficien(t SF). From Formul(a 1),
volume; however, this bulging caused by load application must be taken into consideration in designing a die.(Fig.1)
KShape alteration and load Shape coefficient(SF)= LMW = 10M8 = 80 =0.74
2(H L+W) 2M3M(10+8) 108
A.Shape coefficient (Fig. 2) Take SF=0.74 from Table 1 and from intersection poin(t a)of heavy load urethane M, the elastic modulu(s E)turns out to be approximately
The shape coefficient is defined mathematically as the 4500N/cm2{459kgf}. If we calculate the load by using formul(a 5),
surface area of one load bearing surface divided by the
surface area of all the sides not being subjected to the Load D D Load HMSME HMLMWME 0.[5 cm]M8[0 cm2]M450[0 N/cm2]
surface d H H 3cm
surface Load(F)= = = =60000N{6118kgf}
load directly. Therefore, to cause 5mm of deformation in the height of the urethane, 60000N{6118kgf}of force is necessary.
Shape coefficient(SF)= Surface area of load surfac(e S1) H H=30mm
Surface area of all side(s S2) H H=5mm
H Load surface
On a block shape or pilla(r cylinder)shape, it can be thought WL 60000N
to be divided to each surface respectively(. See Fig. 2). {6118kgf}
a)Block shape
SF= LMW EE(1) a)Block shape b)Pillar shape c)Cylinder shape
2H(L+W)
b)Pillar shape L=100mm
SF= QD2 = D EE(2) (Table 1)Relation between shape coefficient and elastic modulus(values) Not lubricated Lubricated
4QDH 4H
W=80mm
Q:Circularity=3.14 kgf/cm 2 N/cm2
2800
c)Cylinder shape HeavHyeHaloveyaavHdlyoeaualvodryaeluodtahrdueatrunhereetahtnhHaaenneeMH(S(S(h(SorheSSoAhh9roo5e)rreeA9AA598)00)) Example 2
2100 How much is the height of the urethane deformed in the case where a 10000N{1020kgf}of force is applied to a piece with a diameter D of F50mm, and a
SF= D-d EE(3) Elastic modulus E 1750 1.20 27459 height H of 100mm?(Conditions:Heavy load urethane M is used and it is in the non-lubricated state.)(1cm=10mm)
4H 1.15
Coefficient of scale factor 1400 1.10 20594
However, this formula must fulfill below 1.05 17162
conditions. 1050 1.00
13729
1If load is received, the load should bear vertically and 700 20 22 24 26 28 30 First, determine the shape coefficien(t SF)by using formul(a 2),
horizontally against the axis. 630 Deformation% 10297
560 Shape coefficient(SF)= D = 5 =0.125
2The width, length or diameter dimension of load 490 (a) 6865 4H 4M10
surface must be over half of the length or the 420 6178
thickness. 5492 From the intersection poin(t b)of the SF(=0.125)and the curve for heavy load urethane M, the elastic modulu(s E)
4805 becomes approximately 2100N/cm{2 214kgf}, and to determine the amount of deformatio(n H)from Formul(a 6),
B.Elastic modulus ( )FMH
The elastic modulus(E)is defined as the force(stress)per unit of surface
SME
area divided by the percentage of height deformation(distortion).From Table 4119 Amount of deformation in height( H)= = FMH = 4FMH = 4M1000[0 N]M1[0 cm] =2.4cm
1, it can be understood that under non-lubricated conditions, the elastic QM D2 QED 2 3.14M210[0 N/cm2]M5[2 cm2]
modulus changes greatly depending on the shape coefficient. 350 3432 2 ME
Heavy load urethane M(Shore A90) 2746
280
(b) 2059 Therefore, when 1000{0 1020kgf}load is applied, the amount of deformation in height of the urethane is 24mm.
210
D=50mm Load surface 10000N
{1020kgf}
Heavy load urethane S(Shore A80)
Under the above 2 limitations, the elastic modulu(s E)can be determined as
shown below. 140 1373
1275
120 Heavy load/low repulsion type urethan(e Shore A70) Heavy load/low repulsion type urethan(e Shore A70) 1177
100 High deflection urethane foam(porous)
type H=100mm
H=24mm
Elastic modulu(s E)= F/S EE(4) 70 1.5 2 2.5 3 686
H/H 0.1 0.15 0.2 0.25 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 45 H=100mm
(F:Load, S:Load area, H:Change in height, H:Initial height(free height)) kgf=NM0.101972
Shape coefficient SF
C.Load and deformation amount Coefficient of scale factor needs to be considered
The load can be determined by using formul(a 4).
when the deformation rate is 20% or more.
Load(F)= HMSME EE(5) Note)Figures calculated with the formula is for references.
H
Also, the amount of change in the height can be determined in the same way.
Amount of deformation in height = FMH EE(6)
SME
1139 1140
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
COMPONENTS FOR LIFTING"DIE STORING LIFTING BARS
COMPONENTS HLFB Caulking at 2 points $10 30!10
FOR LIFTING"
DIE STORING 10
R1
Name
Catalog No. 6.3
Delivery
0 10 D
00.2
Page 0.3
1
D
LIFTING BARS LIFTING EYE BOLTS CAST-IN LIFTING BUSHES HOOKS Bolt type C2 15 Caulking at 2 points $7
HLFB CHI CSN CHN 30
-
1 1 1 1 L
1142 1143 1143 1144
S45C
With Drop-off prevention stopper
Large head bolt type HOOKS Plate type Large head plate type HOOKS Insert type HOOKS D1 L Allowable load N {kgf} Catalog No. D U/Price
CHNL CHP CHPL CHU CHF - at the use of 4 pcs. Type 25 Q'ty 1O9
34 185 35
1 1 1 1 1 44 240 135 29420 { 3000} HLFB 40 1,350
50 260 190 49033 { 5000} 50 2,100
1144 1145 1146 1147 1148 60 290 210 88260 { 9000} 65 2,500
75 335 240 137293 {14000} 4,300
285 166712 {17000} 4,800
kgf
N+0.101972
Catalog No. 'Volume discount rate P.37
HLFB 25
Large head bolt type LIFTING T-SHAPED BOLTS FIXING PLATES HOLDING PIPES BUSHES FOR RETAINING Order Price Quantity 1O9 10O29 30O49 50O99
CHFL TB DKP DKPL DYP? KPB Rate 5 10 15
1 1 3 TA 3 TA 3A To be quoted on price & lead time above Max. Q'ty.
1148 1148 1149 1149 1150 1Delivery Day
Example Be sure to set the Drop-off prevention stopper downwards.
And its collar should not protrude from the die.
URETHANE STOCK BLOCK SETS STROKE END PIPES URETHANE STOCK BLOCKS ABSORBERS PADS
PH PHN EST ESBT ESU ESUB DUSA DURP
PHBT PHBTN PHUB PHUBN
1 1 1 1
1
1153 1154 1154 1154
1151 1152
Drop-off prevention stopper
1141 ExEpxrperessss PP..3386 Prreessss20200706 http://misumi.jp/press/ FFoorr iinnqquuiirryy,,oordrdereirnignganadnd PP.1.1216797 1142
sesrevrivciecessyysstteemm ootthher innffoorrmmaatitoino,nr,erfefretro to
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
LIFTING EYE BOLTS / CAST-IN LIFTING BUSHES HOOKS
-BOLT TYPE / LARGE HEAD BOLT TYPE-
Lifting eye bolts-For vertical lifting- CHI r A Type B Type CHN
Vertical lift Lift by 45 degrees
R d
M MR D
d
g
da
a
45B
b C
30V C SS400 S C
D Bolt precision JIS1168
90 BÚ
eH
r2 T r1 H B
L S45C
Fe3O4(Black oxide)
Maximum allowable loadN{kgf} Catalog No. U/Price
MMP a b C D H R e g R da A:Vertical 1pc. B:45B2pcs.
Type M Q'ty:1~19
6 M1.0 24.9 14.5 5.2 12.8 28.45 15 CHNL(Large head bolt type)
8 M1.25 32.6 20 6.3 16 33.3 15 3 4.7 1.0 7.9 392{ 40 } 392{ 40} 6 100 d
10 M1.5 41 25 8 20 41.5 18 MR D
12 M1.75 50 30 10 25 51 22 3 6 1.0 9.2 785{ 80 } 785{ 80} 8 80 d1
16 M2.0 60 35 12.5 30 60 27
20 M2.5 72 40 16 35 71 30 4 7.7 1.2 11.2 1471{ 150 } 1471{ 150} 10 90
24 M3.0 90 50 20 45 90 38
30 M3.5 110 60 25 60 110 45 5 9.4 1.4 14.2 2157{ 220 } 2157{ 220} 12 100
36 M4.0 133 70 31.5 70 131.5 55
42 M4.5 151 80 35.5 80 150.5 65 5 13 1.6 18.2 4413{ 450 } 4413{ 450} 16 140
48 M5.0 170 90 40 90 170 70
6 16.4 2 22.4 6178{ 630 } 6178{ 630} CHI 20 210
8 19.6 2.5 26.4 9316{ 950 } 9316{ 950} 24 420
8 25 3 33.4 14710{ 1500 }14710{ 1500} 30 790 S
10 30.3 3 39.4 22555{ 2300 }22555{ 2300} 36 1,520
12 35.6 3.5 45.6 33342{ 3400 }33342{ 3400} 42 2,850 r2 T r1 H
12 41 4 52.6 44130{ 4500 }44130{ 4500} 48 5,040 L B S45C
Fe3O4(Black oxide)
¡{kgf}=NM0.101972
IHow to install Set the eye bolts in the same direction Caution Never use the bolts as MMP D d d1 R1 R2 S T L R H B C N/1pc.{kgf/1pc.} Catalog No. U/Price Q'ty:1~19
Fasten the eye bolt lightly so that the seat when a pair of the bolts are used. shown below. CHN CHNL CHN CHNL Steel safety Type M CHN CHNL
of the bolt is firmly in contact with the plate. coefficient 10
Caution
Catalog No. d1 R1 90B 5B 5B 10M1.5 13 32 42 10 18 20 16 8 46 54 1.5 5 8 9.2 2452{ 250} 10 520 600
9 17 Fd1 5B 5B
6 11 17 12M1.75 16 36 48 13 20 24 20 10 57 64 1.5 6 10 11.7 3530{ 360} 12 570 660
13 20 M
8 16 24 16M2.0 20 40 52 18 25 30 25 13 75 82 2 9 14 16.3 6669{ 680} CHN 16 710 820
20 30 20M2.5 25 48
10 24 34 24M3.0 32 58
28 42
12 36 50 62 20 28 37 32 16 90 98 2 12 17 19.8 1039{5 1060} 20 950 1,090
42 60
16 r1 76 25 33 47 40 20 111 119 2.5 13 19 22.1 15004{1530} CHNL 24 1,380 1,580
48 70
CHI 20 56 76 30M3.5 36 68 88 30 40 56 48 22 131 141 3 16 22 25.6 2383{0 2430} 30 2,330 2,660
24
30 30V 36M4.0 40 78 100 30 40 68 58 25 148 158 3 18 27 31.4 34814{3550} 36 3,280 3,760
90BÚ
36 Lifting with only one ¡{kgf}=NM0.101972
rope for a pair of bolts.
42 Side lift
48 IHow to Install The screw holes for the CHN/CHNL should be finished as shown in a)or b)below. Screw head of CHN/CHNL must be firmly in contact with the surface of the die set.
a) C2
Cast-in lifting bushes CSN r1 M d2 R3 b) M d3 R4 R5
10 15 22 120B 10 12 22 5
r+03 60B 12 18 26 12 14 26 6
r3 16 23 32 r5 16 18 32 6
20 27 40 r4 20 22 40 6
RR MR R Stamped screw diameter Fd224 35 50 24 28 50 8
Fd330 42 6030 34 60 9
20 36 50 72 36 40 72 11
RR
60B Fd 1 0 FD Ú1
-1
1
FD
T+01 T1 +0.5 T2 +0.5 H Order Catalog No. Example
0 0 CHNL 20
LÚ2
S35C
Maximum allowable load N{kgf} 1Delivery Day
Hook Eye bolt MMP D D1 d1 R R1 L T T1 T2 H R Catalog No. U/Price G
2pcs. Vertical lift/1pc. Lift by 45 degrees/2pcs. Type M Q'ty:1~19 IVolume discount rate P.37 G <Large head bolt type>
Be sure to have sufficient
373{0 380} 216{0 220} 2160{ 220} 12M1.75 38 28 18 30 40 55 10 30 15 14 2 CSN 12 430 Price Quantity 1~19 20~49 50~99 100~200 space for the wire.
16 510 Rate - 5%
6620{ 675} 441{0 450} 441{0 450} 16M2.0 46 36 22 35 45 55 10 30 15 18 2 20 700 10% 15%
24 850
8830{ 900} 588{0 600} 5880{ 600} 20M2.5 48 38 28 45 55 70 15 35 20 19 2 30 1,270 To be quoted on price & lead time above Max. Q'ty.
36 1,740
1334{0 1360} 981{0 1000} 9810{1000} 24M3.0 55 45 36 55 65 85 20 45 20 22.5 2
19810{2020} 1667{0 1700} 1667{0 1700} 30M3.5 65 52 42 65 75 95 25 50 20 26 3
58450{5960} 2256{0 2300} 2256{0 2300} 36M4.0 85 70 48 75 90 110 30 55 25 35 3
¡{kgf}=NM0.101972
Catalog No. IVolume discount rate P.37
Order CHI 10 Price Quantity 1~19 20~49 50~99 100~200
CSN 24
Rate - 5% 10% 15%
To be quoted on price & lead time above Max. Q'ty.
1Delivery Day
Example
1143 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1144
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
HOOKS HOOKS
-PLATE TYPE- -LARGE HEAD PLATE TYPE-
CHP 10~40 2-Fg CHP 50 2-Fg 4-C15 CHPL 10~40 2-Fg CHPL 50 4-C15
2-Fg 45B
B D B1
D B D -0.5
FD
d 45B B2 T-1.0
FD FD
B1
45B
D
P Ú0.2 R3 R1 R2 B2
A FD
L
d P Ú0.2 R3 R1 R2 P Ú0.2 R3 R1 R2 d
5B 3B 3B5B A L A
-0.5 L
T-1.0
P Ú0.2 R3 R1 R2
A L
-0.5 T--10..05
T-1.0 CHP 80 4-Fg 5B 3B
g
CHPL 80
g 60 Ú0.2 4-R10
3-Fg D 4-Fg
3-Fg 60 Ú0.2
B CHPL 63 D
CHP 63 FD
B2
60 Ú0.2 4-R10 30B B1 FD
D 60 Ú0.2
B D
FD B2
30B FD 30B
B1
P Ú0.2 R3 R1 R2 30B
A L
30
P Ú0.2 R3 R1 R2 30
A L T--10..05 -0.5
T-1.0
P Ú0.2 R3 R1 R2 30 P Ú0.2 R3 R1 R2 30
A L T--10..05 A L T--10..50
SS400 SS400
d B T L A R1 R2 R3 P N/1pc.{kgf/1pc.} Catalog No. U/Price d B1 B2 T L A R1 R2 R3 P N/1pc.{kgf/1pc.} Catalog No. U/Price
Q'ty:1~19 Q'ty:1~19
g Steel safety Type D g Steel safety Type D
620 710
28 28 18 50 32 10 8 8 16 coefficient 10 10 670 28 28 38 18 61 32 20 9 8 16 coefficient 10 10 770
730 32 32 44 20 67 38 20 9 10 18 850
32 32 20 56 38 10 8 10 18 7 156{9 160} 12 840 7 1569{ 160} 12 960
9 353{0 360} 1,000 9 3530{ 360} 1,150
36 36 24 67 46 13 8 12 22 11 451{1 460} 16 1,310 36 36 50 24 78 46 20 12 12 22 11 4511{ 460} 16 1,510
14 549{2 560} 2,190 14 5492{ 560} 2,530
40 40 26 88 60 18 10 15 30 14 657{0 670} 20 3,090 40 40 56 26 97 60 25 12 15 30 20 3,400
18 1216{0 1240} 4,030 14 6570{ 670} 4,440
48 48 35 92 60 20 12 15 30 22 1912{3 1950} CHP 25 5,180 48 48 68 35 98 60 25 13 15 30 18 12160{1240} CHPL 25 5,700
26 2745{9 2800} 32 22 19123{1950} 32
55 55 40 118 80 25 13 20 40 26 3922{7 4000} 55 55 77 40 125 80 30 15 20 40 26 27459{2800}
26 5099{5 5200} 70 70 100 50 143 93 35 15 24 45 26 39227{4000}
70 70 50 138 93 30 15 24 45 40 - 90 120 50 170 115 35 20 30 55 26 50995{5200} 40
{K kgf}=NM0.101972 - 115 155 50 175 115 40 20 30 55
- 90 50 170 115 35 20 30 55 50 - 140 180 50 185 120 40 25 30 60 {K kgf}=NM0.101972 50
- 115 50 175 115 40 20 30 55 63 63
- 140 50 185 120 40 25 30 60 80 80
Gi:Dimensions that are different from CHP.
Catalog No. IVolume discount rate P.37 To be quoted on Catalog No. IVolume discount rate P.37 To be quoted on
CHP 25 price & lead time CHPL 25 price & lead time
Order Price Quantity 1~19 20~49 50~99 100~200 above Max. Q'ty. Order Price Quantity 1~19 20~49 50~99 100~200 above Max. Q'ty.
10% 15% 10% 15%
Rate - 5% Rate - 5%
1Delivery Day Example Make sure that the direction of lifting 1Delivery Day Example Make sure that the direction of lifting
is in line with the axes of the mounting bolts. is in line with the axes of the mounting bolts.
IBolts for CHP 50C63C80 (Strength rank 10.9) IBolts for CHPL 50C63C80 (Strength rank 10.9)
Screw Catalog No. U/Price G KPlease use bolts belonging Screw Catalog No. U/Price G KPlease use bolts belonging
to the strength rank 12.9 or to the strength rank 12.9 or
length Type M-L LessG OverG Quantity 10.9 of JIS B 1176 or B 1180. length Type M-L LessG OverG Quantity 10.9 of JIS B 1176 or B 1180.
Full threads CB 24 - 80 246 243 15 Full threads CB 24 - 80 246 243 15
90 262 259 90 262 259
60 100 284 281 10 Details P.721 60 100 284 281 10 Details P.721
110 307 303 110 307 303
1145 1146
120 328 324 120 328 324
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
HOOKS HOOKS-CAST-IN TYPE-/ LIFTING T-SHAPED BOLTS
-INSERT TYPE-
CHF R3
R5
R2
D1
R5R2
D
D2
R3
D
D2
TA B CE
CHFL S25C or equivalent
25 25 (Large head bolt type)
R3
CHU70R
R5
R4
CHU60R R20 R15 R20 R15 D1
R4
130
R50 R5
D
80
60 D2
130 R3
D
50 D2
140
80
70
140
50
30 70 45 R50 40 70
140
CHU60L 150 50 TA B CE S25C or equivalent
215 68
75
240
CHU70L D1 B N/1pc. Catalog No. U/Price Q'ty:1~19
D D2 T A CE
30 Type D CHF CHFL
CHF CHFL 40 {kgf/1pc.} 730 810
45 940 1,040
25 46 60 36 12.6 25 60 15 16.6 794{0 810} 25
70 1,250 1,380
32 55 70 42 13.1 30 80 20 16.8 13140{1340} 32 1,570 1,730
36 2,610 2,880
36 60 80 46 18.5 35 25 17 16570{1690} CHF 4,700 5,180
40 70 90 55 18.9 35 30 17.4 20500{2090} CHFL 40
50
50 90 120 70 25.2 35 40 18.1 32070{3270}
70 120 140 100 31.1 40 40 19.4 62860{6410} 70
38 38 ¡{kgf}=NM0.101972
TB T Hex nut
26 A
26
R1 R MB t
A H
Marking MB t
R2 L
26 SS400 26 SS400 8 13 6.5
Fd=M
MMP Cross section A-A 10 17 8
12 19 10
16 24 13
{N kgf}/1pc. U/Price Catalog No. 20 30 16
Steel safety Q'ty:1~19 CHU 60R
coefficient 10 Catalog No. Order SS400
6,710
42170{4300} Bolt precision JIS1168
8,470
47070{4800} 60R Hex nut
60L
CHU 70R 1Delivery Day N/1pc. Catalog No. U/Price
70L
MMP H R1 R2 T r {kgf/1pc.} Type M L
Q'ty:1~19
IVolume discount rate P.37 8M1.25 8 2 3 80 22 686{ 70} 8 100 600
¡{kgf}=NM0.101972 Price 10M1.5 83 5 80 28 98{1 100} 10 110 660
IBolts for CHU Quantity 1~19 20~49 50~99 100~200 12M1.75 8 3 5 90 34 1471{150} TB 12 125 720
Rate - 5%
(Strength rank 10.9) 10% 15% 16M2.0 10 5 6 100 45 2942{300} 16 135 900
Screw Catalog No. U/Price G To be quoted on price & lead time above Max. Q'ty. 20M2.5 10 5 8 120 50 3923{400} 20 160 1,200
length Type M - L
LessG OverG Quantity ¡{kgf}=NM0.101972
Full threads CB 24 - 80 246 243 15 Example
90 262 259 Catalog No. L Cast-in side
125
60 100 284 281 10 Order CHF 50 Example
110 307 303 Delivery TB 12
120 328 324 1 Day
Details P.721 ¡Please use bolts belonging
to the strength rank 12.9 or
10.9 of JIS B 1176 or B 1180. Rounding
IVolume discount rate P.37 To be quoted on Caution Caution Never use T-Shaped bolts as shown below.(TB)
price & lead time
Rounding Price Quantity 1~19 20~49 50~99 100~200 above Max. Q'ty.
Welding IT-shaped bolt Rate - 5% 10% 15%
How to install
Screw the bolt into the plate with your hand,
and then tighten the hex nut firmly to fix the bolt.
GTightening the nut this way allows you to
freely adjust the T-bar orientation.
Side lift Lifting with only one
rope for a pair of bolts.
1147 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1148
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FIXING PLATES / HOLDING PIPES BUSHES FOR RETAINING
Fixing plates DKP Catalog No. 5mm increments U/Price KPB
F Q'ty:1~9
Holding pipes Type L
Example
2-F18 4-C1.5 200 95~150 780
DKP 250 145~200 940 L
C1 R
9 50 300 195~250 1,070 10
E
25 F(5mm increments) Catalog No. 5mm increments U/Price
L
Type L F Q'ty:1~9 D1
D Ú0.1
200 120~150 1,380 5
250 170~200 1,530 5
220~250 1,690 P Ú0.1
DKPL 300 270~300 1,840
(Single oval hole type)
350
DKPL (Single oval hole type) 400 320~350 2,000 R¯1
34 F18 4-C1.5 Catalog No. F 10 5T R
C1
25 F(5mm increments) Order DKP 200 F95 4-Fd Urethane sheet
L DKPL 250 F180 Hole for confirming seating Shore A90
SS4009 50 Delivery 3 Days P.38
18 Price
DYPA Express T 600/1pc. SS400
DYPB Express A 300/1pc. Painting(Yellow)
DYPC
A flat charge of 810 yen for 3 pieces Painted area:Outer circumference ofR
DL or more of the same size
SGP Applicable post Catalog No. U/Price
(excluding Express T). Q'ty:1~9
DYPACDYPBCDYPC IVolume discount rate P.37 diameter, D D1 P L RT E d R Type No.
DKPCDKPL bushing inner 10 1,800
Quantity 1~9 10~19 20~49 50~100 1.0 2,220
Rate - 5% 10% 15% diameter 1.0 2,880
1.5 3,750
25 27 40 24 58 33 8 15 1.5 25 4,830
1.5
To be quoted on price & lead time above Max. Q'ty. 32 34 47 31 74 42 10 22 10 32
38 40 56 37 88 50 12 25.5 15 KPB 38
Dt Catalog No. U/Price 50 52 70 49 115 65 15 37.5 15 50
139.8 4.5 Q'ty:1~9
165.2 5 Type L
190.7 5.3 980
100 1,260 60 62 82 59 138 78 18 47.5 15 60
150 1,520
DYPA 1,230
1,580
200 1,920 INotes for users
1,690
DYPB 100 2,140 Use this bush for retaining the die when it is not in use.
150 2,600 Urethane sheet is pasted as a cushioning material.
4 holes for confirming seating are provided around the circumference of the bush.
t 200
25
25
DYPC 100
150
200 INotes
Order Catalog No. Do not use this bush when conveying or shipping the dies.
DYPA 150 Do not use this bush with the double-layer die.
Delivery 3 Days P.38 Order Catalog No.
Price KPB 50
Express T 600/1pc. Example
Express A 300/1pc.
A flat charge of 810 yen for 3 pieces 3Delivery Days Express A 800/1pc. P.38
or more of the same size
A flat charge of 2,160 yen for 3 pieces
(excluding Express T). or more of the same size.
IVolume discount rate P.37
Quantity 1~9 10~19 20~49 50~100
Rate - 5% 10% 15%
To be quoted on price & lead time above Max. Q'ty. IVolume discount rate P.37
Price Quantity 1~9 10~19 20~49 50~100
Rate - 5% 10% 15%
To be quoted on price & lead time above Max. Q'ty.
KPB
1149 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1150
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
URETHANE STOCK BLOCK SETS
234 PHBT(Set of ESBT and PH) B 234 PHUB(Set of ESUB and PH) B
ESBT ESUB
D ESBT PH A D ESUB PH A
1PH d L 1PH d L
20 15 t 20 15 t
Bottomless L d1 W Ú0.5 Bottomless L d1 W Ú0.5
D D1 D D1
2 2
EST ESU
3 25 3 25
F13 F13
4 CB 3S 25 20 A SGP 4 CB 3 SU 25 20 A SGP
L1+00.3 (Stroke end pipe) B SS400 L1+00.3 (Stroke end pipe) B SS400
2 Shore A90 2 Shore A90
(Urethane stock block) (Urethane stock block)
Urethane stock block Stroke end pipe Sleeve Bolt Catalog No. U/Price Urethane stock block Stroke end pipe Sleeve Bolt Catalog No. U/Price
234ESBT 1PH 234ESUB 1PH 3SU 4
DLd 3S 4 Type D L L1 Color DLd W Type D L L1 Color
40 80 D1 L1 d1 t W 80 Q'ty:1~9Sets D1 L1 d1 t 91 SU14 CB8-45 80 Q'ty:1~9Sets
50 110 60.5 60 52.9 3.8 40 110 40 80 14 140
89.1 85 80.7 91 50 140 60 1,660 60.5 60 52.9 3.8 (Q'ty:1) 40 60 R(Red) 1,660
14 90 140 22 CB12-55 90
70 90 4.2 119 S14 CB8-45 140 85 2,520 139.8 90 130.8 4.5 PHUB
101.6 100 93.2 (Q'ty:1) 170 SU22 (Q'ty:1)
90 140 140 90 4,060 90 Y(Yellow) 5,640
110 132 4,090
22 90 70 100 R(Red)
90 110
100 139.8 100 130.8 4.5
110 PHBT 90 Y(Yellow) 5,640
90 100
170 234 PHUBN(Set of ESUB and PHN) PHN
165.2 100 155.2 5.0 CB12-55 110 5,680 ESUB L AB
110 D ESUB
S22 (Q'ty:1) 1PHN d
195 100 90 8,270 L
100 D
15 t
110 8,360
234 PHBTN(Set of ESBT and PHN) PHN 2
ESBT L ESU
D ESBT
1PHN d AB With bottom 1.6 d2
L 20 d1
D D1
15 t L1+00.3
4 CB 3 SU A SGP
B SPC
(Urethane stock blocks) (Stroke end pipe) 2 Shore A90
2 Urethane stock block Stroke end pipe Catalog No. U/Price
EST 234ESUB 1PHN L1 Color
With bottom 1.6 d2 DLd D1 L1 d1 d2 Sleeve Bolt L Q'ty:1~9Sets
20 d1 3SU 4
D1 t Type D
L1+00.3
40 80 14 60.5 60 52.9 9 3.8 SU14 CB8-45
4 CB 3S A SGP (Q'ty:1) 40 80 60 1,880
B SPC
(Urethane stock block) (Stroke end pipe) 2 Shore A90 70 110 22 101.6 85 93.2 13 CB12-55 PHUBN 70 110 R(Red)
4.2 SU22 (Q'ty:1) 85 3,820
Y(Yellow)
Urethane stock block Stroke end pipe Sleeve Bolt Catalog No. U/Price CB12-55 90 140 110 5,940
234ESBT 1PHN 90 140 22 139.8 110 130.8 13 4.5 SU22 (Q'ty:1)
DLd 3S 4 L L1 Color
40 80 D1 L1 d1 d2 t Type D Q'ty:1~9Sets
50 110 14 80
70 60.5 60 52.9 3.8 S14 CB8-45 PHBTN 40 110 60 1,880
90 140 22 (Q'ty:1) 50
100 89.1 85 80.7 9 4.2 70 140 85 R(Red) 2,680 IThe combination list of stroke end pipes and urethane stock blocks
90
101.6 93.2 100 4,330
110 Y(Yellow) 5,940
139.8 110 130.8 13 4.5 S22 CB12-55 Set name Stroke end pipe Urethane stock block
5.0 (Q'ty:1)
152.5 142.5 8,470 Components
3Sleeve
1234 1 234 2Urethane 4Bolt
Order Catalog No. L L1 RCY 1Delivery Day PHBT PH (P.1153) CB
PHBTN PHN (P.1153) (P.721)
PHBT 50 110 85 R ESBT EST S
PHBTN 70 140 110 Y (P.1154) (P.1154) (P.1154)
PHUB 40
PHUBN 90 80 60 R IVolume discount rate P.37 PHUB PH (P.1153)
140 110 Y PHUBN PHN (P.1153)
Price Quantity 1~9 10~19 20~49 50~100 ESUB ESU SU
Rate - 5% 10% 15% (P.1154) (P.1154) (P.1154)
To be quoted on price & lead time above Max. Q'ty.
1151 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1152
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
STROKE END PIPES STOCK BLOCKS / ABSORBERS / PADS
PH (Bottomless) B Urethane stock blocks EST D ESBT ESU D ESUB
ESTCESBT d d
L1
15 t A
20 d
D1 W Ú0.5 L
L
D
12 1 2 Shore A90
3 1 Catalog No. U/Price Q'ty:1~9 Catalog No.
F13 d Urethane ESTCESBT ESUCESUB 2 EST 40-80
25
Type D-L ESTCESU ESBTCESUB Order
25 20 SGP E40-80 CB8-45 * 40- 80 710 720
A SS400 (Q'ty:1)
+0.3 B 14 E50-110 S14 SU14 50-110 1,350 1,360 1Delivery
U/Price
L0 Color Q'ty:1~9
R(Red) 980 E70-140 Day
1,230
ESTCESBT Catalog No. Y(Yellow) 1,300 EST 70-140 2,890 2,900
D L1 1,340
40 80 D1 d t W Type D L 1,500 E7022110 ESBT * 7022110 2,390 2,420
50 110 60.5 52.9 3.8 91 1,540
70 140 89.1 80.7 4.2 119 40 60 1,810 E7022140 *ESU * 7022140 2,930 2,960 IVolume discount rate P.37
101.6 93.2 4.2 132 85 1,900 22 E90-120
90 140 139.8 130.8 4.5 170 90C100 2,140 S22 SU22 CB12-55 *ESUB 90-120 3,730 3,860 Price Quantity 1~9 10~19 20~49 50~100
110 2,280 E90-140 (Q'ty:1) Rate - 5% 10% 15%
100 140 165.2 155.2 5 195 50 90C100 * 90-140 4,330 4,360
110
110 140 190.7 180.1 5.3 220 70 90C100 E100-140 100-140 6,770 6,800 To be quoted on price & lead time above Max. Q'ty.
110 ESU and ESUB are available only in the sizes marked with an *.
90C100 For applicable urethane P.1124
110
PH 90 Sleeves d1 d2 d3 d4 R R1 R2 R3 Urethane U/Price
d Catalog No. Q'ty:1~19
S 16 9
100 SU Fd4 24 13 30 14 S14 130
Fd3 24 13
15B Fd2 14 9 13 19 35 22 S22 170
22 13 20 27
100 22 S22-100 500
(L170 or more)
110 14 SU14 130
30 7 10 3 SU22 170
22
45B
PHN (With bottom) 5 Order Catalog No. 1Delivery Day
S 14
ESTCESBT AB r
D r1 r2 r3
15 t Fd 2 Fd1 IVolume discount rate P.37
rFd1
L1 12 5SS400PriceQuantity 1~19 20~4950~99100~200 To be quoted on price &
Rate - 5% 10% 15% lead time above Max. Q'ty.
36DUSA
12 5DURP
50R3
Urethane absorbers Urethane pads FD
F20
FD F19.5
F20
F19.5
1.6 d1
20 d
D1
L+00.3
A SGP F10.5 F10.5 Shore A90
B SPC F15 F15
ESTCESBT D1 d d1 t Catalog No. L Color U/Price Catalog No. U/Price Catalog No. 1Delivery Day
D L1 9 Q'ty:1~9 Q'ty:1~9
40 80 60.5 52.9 3.8 Type No. 60 R(Red) Type D Order DUSA 50
50 110 89.1 80.7 13 4.2 85 Y(Yellow) 1,200 550 Price
70 110 101.6 93.2 9 4.2 40 85 1,390 DUSA 50 900 IVolume discount rate
70 140 101.6 93.2 4.2 110 1,520 70 740
70 140 101.6 93.2 13 4.2 50 110 1,580 1,060 Quantity 1~9 10~19 P.37
90 140 139.8 130.8 4.5 110 1,620 Rate - 5%
100 140 152.5 142.5 RCY 5 70 110 1,800 DURP 40 20~49 50~100 To be quoted on price &
110 140 190.7 180.1 R 5.3 110 2,010 50 10% 15% lead time above Max. Q'ty.
70 2,390
L PHN 7022 U/Price Catalog No.
Q'ty:1~19 S10.5
110 90 Sleeve S10.5 F19.5 Catalog No. Order
F10.5 S10.5 150
100
110
Catalog No. IVolume discount rate P.37 17 1Delivery Day
PH 70 12
Order Price Quantity 1~9 10~19 20~49 50~100
Rate - 5%
10% 15%
To be quoted on price & lead time above Max. Q'ty. IVolume discount rate P.37
1Delivery Day F15 Price Quantity 1~19 20~49 50~99 100~200 To be quoted on price &
Rate - 5% 10% 15% lead time above Max. Q'ty.
SS400
1153 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1154
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES FINISHED BLOCKS
FINISHED PLATES SKD11 FINISHED PLATES DC53
FINISHED BLOCKS
SKD"S-SKD"E-SKD DC"S-DC"E-DC
Name
Catalog No. 3A 3A
Delivery 1159 1161
Page
SKS3 SKS93 HPM2T
SKS"S-SKS"E-SKS FINISHED PLATES HPM"S-HPM"E-HPM
SK"S-SK"E-SK
3A 3A
3A
1163 1167
1165
S50C SS400 A7075P-T651
SC"S-SC"E-SC FINISHED PLATES ALP
SS"S-SS"E-SS
3A 3A
3A
1169 1173
1171
SKH51 SKD11 DC53 SKS3 SKS93 S50C
FB-SKH FB-SKD FB-DC FB-SK FB-SC
1175 1175 1175 FINISHED BLOCKS 1175 1175
FB-SKS
3A
1175
HARDENED PLATES CARBIDE BLOCK MATERIALS
HPSH HPHE Z
11 1
1181 1182
1155 1156
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES
-GUIDE-
ICharacteristics of materials ISize Material being engraved Standard size Dimensions A, B and T are standardized. Frequently used 6000
sizes are the basic size. The price is lower than the free size.
A
Name Page Material Chemical composition Features Characteristics of comparisonG
SKD11 (%)
Plate Block Hardened plate Carbide block P.1159 ¡Possesses high hardenability Abrasion Strength for Toughness Hardenability Distortion by Machinability Free size Dimension A can be specified by 1mm increment up to maximum of 500mm.
materials P.1175 C 1.40~1.60 with air hardening and vacuum resistance hot working heat treatment Alternation is available for dimension B and T change by 1mm increment.
Si 0.15~0.35 hardening capabilities
Mn 0.30~0.60 B
P ~0.025 ¡Minimal and stable rate of
SKD - - S ~0.010 distortion by heat treatment. ABBAAC Economy type Dimension specification is as same as Free size type. 6-face milling cutter
S-SKD FB-SKD Cr 11.00~13.00 finished and lower price than Free size type.
E-SKD Mo 0.80~1.20 ¡Superior in abrasion resistance.
V 0.20~0.50
Alteration Alterations are available only for free size type and economy type.
T
¡Dimension BEEEEEEStandard dimension B can be specified in 1mm increments, allowing for a
¡More toughness than die steel SKD11. minimum of 30mm.
C ¡Possesses equivalent hardness as ¡Dimension TEEEEEEPlate thickness dimension T can be specified in 1mm increments, allowing for
SKD11 when low temperature a minimum of 5mm.
DC Si tempered, and 62HRC when high
S-DC FB-DC ¡Dimension T toleranceEEEAn additional 0.3mm allowance for machining can be added to the standard
E-DC - - P.1161 DC53 Mn Patented steel: temperature tempered. A B A A B B tolerance in order to make it easier to correct warpage caused by heat treatment.
P.1175 P
S SKD11 group ¡Superior in machinability and ¡ChamferingEEEEEECircumferential chamfering(C0.5mm~C1.0mm)can be altered to C0.1mm or
grindability due to its even texture less.
Cr by carbide adjustment.
C 0.90~1.00 ¡Spheroidizing annealing offers ITolerance for finished plates Precision standards
Si 0.15~0.35 good machinability.
SKS - - P.1163 SKS3 Mn 0.90~1.20 C D B C D A (Standard size) (Free size) (Economy type) Parallelism of upper
S-SKS FB-SKS P.1175 P ¡Higher hardenability than SK and lower planes
E-SKS S ~0.025 and its oil hardening capability SKD S-SKD E-SKD
Cr ~0.010 offers lower heat treatment DC S-DC E-DC Standard and free size Max. 0.012 per 100mm
W 0.50~1.00 deformation. SKS S-SKS E-SKS
0.50~1.00 SK S-SK E-SK Economy type Max. 0.05 per 100mm
HPM S-HPM E-HPM
C 1.00~1.10 ¡Spheroidizing annealing offers SC S-SC E-SC Flatness of upper T Less than 8 8~15 16~25 26 or more
SS S-SS E-SS and lower planes Per 100mm 0.05 0.03 0.015 0.012
Standard and free size
SK Si 0.15~0.35 good machinability. Economy type Per 100mm 0.1 0.07 0.05 0.05
S-SK FB-SK
E-SK - - P.1165 SKS93 Mn ~1.10 ¡Higher hardenability than SK D D C D D A Tolerance of For HPM(T=8mm):0.0(5 0.1)( )is for economy type
P.1175 P ~0.030 and its oil hardening capability dimension T
HPM2T S50C SS400 SKD11 DC53 SKS3 SKS93
S ~0.030 offers lower heat treatment B Standard and free size +0.3 +0.5
Material being engraved +0.1 +0.2
Cr 0.20~0.60 deformation.
¡No heat treatment required as it's Economy type +0.4 +0.6
+0.2 +0.3
prehardened steel(40HRC). A
C ¡Good machinability as S50C Tolerance of 99mm or less 100~250mm 251mm or more
(20HRC). dimension A/B +0.5 +0.8
Si ¡Great nitration property. 0 0
HPM Standard and free size +0.4
S-HPM - - - P.1167 HPM2T Mn Patented steel: ¡Possess even hardness and D D C -- A 0
E-HPM P strength. Economy type
Cr-Mo group (Note)Free cutting agents Perpendicular of Alteration of
S are used. Specify polishing reference plane circumferential chamfering
Cr or crimping according to the Standard and free size Max. 0.015 per 100mm Standard and free size
usage. Economy type Economy type C0.5~C1.0
Roughness of Refereence Upper and Others
surface plane lower surface
C 0.47~0.53 ¡Generally used for induction T Standard and free size 1.6a 3.2a 6.3a
(6S) (12S) (25S)
SC P.1169 Si 0.15~0.35 hardening parts such as gears
S-SC FB-SC - - P.1175 S50C Mn 0.60~0.90 and shafts. E E B E E AA 1.6a 6.3a 6.3a
E-SC (6S) (12S) (25S)
P ~0.030 ¡Possesses moderate hardness Economy type
S ~0.035 and good machinability.
SS - - - P.1171 SS400 P ~0.050 ¡C and Mn are not contained and F E B E E AA
S-SS S ~0.050 possesses good bending, elongation,
E-SS
and welding capabilities. Precision standards
T 10 15 20 25 30~50
Si ~0.400 ¡The best tensile strength ALP Per 100mm 0.03 0.05 0.07 0.09 0.11
Fe ~0.500
A7075P Cu 1.2~2.0 and bearing force among Parallelism of upper Max. 0.75 per 1,000mm
and lower planes
- P.1173 -T651 Mn ~0.300 the aluminum material and - - - - - Flatness of upper +0.5
( )ALP - - suitable for weight saving - A and lower planes +0.3
Mg 2.1~2.9 of press dies. Tolerance of
Ultra high Cr 0.18~0.28 (Ultra high strength duralumin) dimension T
strength
duralumin Zn 5.1~6.1
Ti ~0.020
C 0.80~0.90 TB
- HPSH P.1175 Si 0.15~0.35 ¡No softening occurs even when Tolerance of 99mm or less 100~250mm 251mm or more
HPHE P.1181 Mn used as a high alloy tool at a dimension A/B
P 0.25~0.40 +0.4 +0.5 +0.8
FB-SKH - SKH51 ~0.025 A A A B B B 0 0 0
S ~0.010 high temperature. Used for
Cr 3.80~4.50
W 6.00~7.00 general cutting purposes that
Mo 4.80~5.80 requires toughness.
V 1.80~2.30 Perpendicular of Max. 0.015 per 100mm
reference plane
¡Carbide
--- Z P.1182 V30 Co 8~16 AA C D -- E Alteration of C0.2~0.3
Products information for carbide materials for tools circumferential chamfering
(Carbide)
P.1226 Roughness of
surface Refereence Upper and
GThe degree of excellence is shown in the order of AA, A, B, C, D, E, F. (AA is the best.) plane lower surface Others
1157 1.6a 3.2a 6.3a 1158
(6S) (12S) (25S)
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES -SKD- Heat treatment data P.1184
-STANDARDCSIZE SPECIFIEDCECONOMY TYPE-
SKD (Standard type) Price calculation formula Upper : Size specified type Price calculation formula Upper : Size specified type
S-SKD (Size specified type) (AMPrice coefficient) Lower : Economy type (AMPrice coefficient) Lower : Economy type
E-SKD (Economy type)
AT 10 13 15 16 20 22 25 30 35 AT 10 13 15 16 20 22 25 30 35
A (1mm incr.) B (1mm incr.) B
Dimension tolerance
Precision standards P.1158 T Type 30~ 60 AM31 AM30 AM32 AM32 AM35 AM36 AM40 101~ 150 AM45 AM45 AM46 AM46 AM52 AM55 AM59 AM67 AM74
AM28 AM27 AM29 AM29 AM32 AM33 AM36 AM41 AM41 AM42 AM42 AM47 AM50 AM54 AM61 AM67
ACB T
B 99mm or less +0.4 61~ 80 AM25 AM24 AM25 AM25 AM29 AM30 AM34 151~ 180 AM45 AM45 AM46 AM46 AM52 AM55 AM59 AM67 AM74
SKD 0 AM23 AM22 AM23 AM23 AM27 AM27 AM31 AM41 AM41 AM42 AM42 AM47 AM50 AM54 AM61 AM67
Standard
Size specified 100~250mm +0.5 +0.5 81~ 100 AM25 AM24 AM25 AM25 AM29 AM30 AM34 181~ 200 AM41 AM40 AM42 AM42 AM45 AM50 AM55 AM64 AM74
0 +0.2 AM23 AM22 AM23 AM23 AM27 AM27 AM31 AM37 AM36 AM38 AM38 AM41 AM45 AM50 AM58 AM67
251mm or more +0.8 AM24 AM23 AM24 AM24 AM26 AM28 AM30 AM39 AM37 AM40 AM40 AM45 AM50 AM55 AM64 AM74
0 AM22 AM21 AM22 AM22 AM24 AM26 AM27 AM36 AM34 AM36 AM36 AM41 AM45 AM50 AM58 AM67
101~ 200 60 201~ 210
99mm or less +0.4
0
AM24 AM23 AM24 AM24 AM26 AM28 AM30 AM39 AM37 AM40 AM40 AM45 AM50 AM55 AM64 AM74
Economy 100~250mm +0.5 +0.6 201~ 300 AM22 AM21 AM22 AM22 AM24 AM26 AM27 211~ 250 AM36 AM34 AM36 AM36 AM41 AM45 AM49 AM58 AM67
0 +0.3 251~ 300 AM39 AM37 AM40 AM40 AM45 AM50 AM54 AM64 AM74
150 AM36 AM34 AM36 AM36 AM41 AM45 AM49 AM58 AM67
251mm or more +0.8 AM21 AM20 AM21 AM21 AM23 AM25 AM28
0 301~ 400 AM19 AM18 AM19 AM19 AM21 AM23 AM26
SKD11(Raw material) 401~ 500 AM21 AM20 AM21 AM21 AM23 AM25 AM28 301~ 350 AM39 AM37 AM40 AM40 AM45 AM50 AM52 AM64 AM74
AM19 AM18 AM19 AM19 AM21 AM23 AM26 AM36 AM34 AM36 AM36 AM41 AM45 AM47 AM58 AM67
Catalog No. AB T IVolume discount rate P.37 To be quoted on 30~ 80 AM32 AM31 AM33 AM33 AM36 AM37 AM41 AM46 AM50 351~ 400 AM39 AM37 AM40 AM40 AM45 AM48 AM52 AM63 AM73
price & lead time AM29 AM28 AM30 AM30 AM33 AM34 AM37 AM42 AM45 AM36 AM34 AM36 AM36 AM41 AM44 AM47 AM57 AM66
Order SKD 100 80 10 Price above Max. Q'ty.
S-SKD 230 100 16 Alteration Quantity 1~9 10~30 81~ 100 AM25 AM25 AM25 AM25 AM30 AM32 AM33 AM40 AM43 401~ 450 AM39 AM37 AM40 AM40 AM45 AM48 AM52 AM63 AM73
E-SKD 365 250 13 AM23 AM23 AM23 AM23 AM27 AM29 AM30 AM36 AM39 AM36 AM34 AM36 AM36 AM41 AM44 AM47 AM57 AM66
Rate - 5%
A(dimension A)MPrice coefficient=Unit price 101~ 125 AM24 AM23 AM25 AM25 AM29 AM30 AM32 AM40 AM43 451~ 500 AM39 AM37 AM40 AM40 AM45 AM48 AM58 AM63 AM73
AM22 AM21 AM23 AM23 AM27 AM27 AM29 AM36 AM39 AM36 AM34 AM36 AM36 AM41 AM44 AM53 AM57 AM66
(ex)S-SKD-230-100-16
3Delivery Days 230 M 28 =\6,440 126~ 150 AM24 AM23 AM25 AM25 AM29 AM30 AM32 AM40 AM43 101~ 160 AM44 AM43 AM45 AM45 AM51 AM54 AM54 AM65 AM73
151~ 160 AM40 AM39 AM41 AM41 AM46 AM49 AM49 AM59 AM66
P.1174(B and T dimension changeable) 80 AM22 AM21 AM23 AM23 AM27 AM27 AM29 AM36 AM39
AM39 AM37 AM41 AM41 AM45 AM48 AM54 AM63 AM73
Alterations are available for size specified and economy type. AM24 AM23 AM25 AM25 AM29 AM30 AM32 AM40 AM43 161~ 200 AM36 AM34 AM37 AM37 AM41 AM44 AM49 AM57 AM66
AM22 AM21 AM23 AM23 AM27 AM27 AM29 AM36 AM39
Express A 800/1Pc. P.38
161~ 200 AM24 AM23 AM25 AM25 AM29 AM30 AM32 AM40 AM43 201~ 250 AM36 AM35 AM41 AM41 AM45 AM48 AM52 AM63 AM73
A flat charge of 2,160 yen for 3 U/Price AM22 AM21 AM23 AM23 AM27 AM27 AM29 AM36 AM39 AM33 AM32 AM37 AM37 AM41 AM44 AM47 AM57 AM66
pieces or more of the same size. A B T 40 50 60 70
250 160 16,200 19,890 24,470 28,960 201~ 250 AM24 AM22 AM25 AM25 AM25 AM28 AM30 AM35 AM40 251~ 300 AM36 AM35 AM41 AM41 AM45 AM48 AM52 AM63 AM73
AM22 AM20 AM23 AM23 AM23 AM26 AM27 AM32 AM36 301~ 350 AM33 AM32 AM37 AM37 AM41 AM44 AM47 AM57 AM66
160 AM36 AM35 AM40 AM40 AM45 AM48 AM51 AM63 AM73
AM24 AM22 AM25 AM25 AM25 AM28 AM30 AM33 AM37 AM33 AM32 AM36 AM36 AM41 AM44 AM46 AM57 AM66
251~ 500 AM22 AM20 AM23 AM23 AM23 AM26 AM27 AM30 AM34
U/Price (Standard type) U/Price (Standard type) 30~ 100 AM33 AM32 AM34 AM34 AM40 AM42 AM45 AM52 AM55 351~ 400 AM36 AM35 AM39 AM39 AM44 AM47 AM51 AM62 AM72
A B T 10 13 15 16 20 22 25 30 35 AM30 AM29 AM31 AM31 AM36 AM38 AM41 AM47 AM50 AM33 AM32 AM36 AM36 AM40 AM43 AM46 AM56 AM65
60 1,320 1,190 1,240 1,280 1,460 1,500 1,760 A B T 10 13 15 16 20 22 25 30 35
80 60 1,540 1,460 1,500 1,540 1,720 1,810 2,120 AM28 AM26 AM29 AM29 AM33 AM35 AM35 AM45 AM47 401~ 450 AM36 AM35 AM39 AM39 AM44 AM47 AM51 AM62 AM72
500 7,880 7,220 8,060 8,100 9,020 10,340 11,220 150 4,670 4,450 4,800 4,890 5,420 5,900 6,470 7,570 8,540 101~ 125 AM26 AM24 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM33 AM32 AM36 AM36 AM40 AM43 AM46 AM56 AM65
80 1,810 1,630 1,720 1,760 1,980 2,070 2,160 2,600 2,730
100 2,120 1,900 1,980 2,030 2,290 2,380 2,560 3,000 3,130 180 5,280 5,020 5,640 5,770 6,250 7,000 7,570 8,540 9,900 126~ 150 AM26 AM25 AM29 AM29 AM33 AM35 AM35 AM45 AM47 451~ 500 AM36 AM35 AM39 AM39 AM44 AM47 AM70 AM62 AM72
125 2,420 2,200 2,380 2,420 2,690 2,860 3,000 3,480 3,700 AM24 AM23 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM33 AM32 AM36 AM36 AM40 AM43 AM63 AM56 AM65
150 3,000 2,780 3,040 3,130 3,610 3,830 4,140 4,620 5,280 200 5,720 5,500 6,300 6,470 6,910 7,880 8,410 9,240 10,920
151~ 160 AM26 AM25 AM29 AM29 AM33 AM35 AM35 AM45 AM47 101~ 200 AM55 AM57 AM57 AM62 AM65 AM66 AM83 AM85
80 210 6,080 5,810 6,600 6,820 7,400 8,280 8,850 9,860 11,580 AM24 AM23 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM50 AM52 AM52 AM56 AM59 AM60 AM75 AM77
160 3,170 2,860 3,130 3,220 3,700 3,920 4,230 4,710 5,460
200 3,570 3,350 3,880 3,920 4,360 4,580 4,890 5,640 6,520 250 7,310 7,040 8,010 8,320 9,240 9,860 10,480 12,240 14,170 161~ 180 AM26 AM25 AM29 AM29 AM33 AM35 AM35 AM45 AM47 201~ 250 AM50 AM53 AM53 AM59 AM61 AM66 AM76 AM85
250 4,140 3,960 4,710 4,800 5,200 5,550 5,860 6,600 7,750 150 AM24 AM23 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM45 AM48 AM48 AM54 AM55 AM60 AM69 AM77
500 7,880 7,750 9,160 9,290 9,460 10,920 11,580 13,160 15,400
100 2,380 2,290 2,380 2,420 2,690 2,860 3,000 3,480 3,700 300 8,800 8,500 9,510 9,770 11,360 11,750 12,680 14,610 17,160 181~ 200 AM26 AM25 AM29 AM29 AM33 AM35 AM35 AM45 AM47 251~ 300 AM50 AM53 AM53 AM59 AM61 AM66 AM76 AM85
125 2,950 2,690 2,820 2,910 3,300 3,390 3,520 4,490 4,800 AM24 AM23 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM45 AM48 AM48 AM54 AM55 AM60 AM69 AM77
150 3,390 3,080 3,170 3,300 3,740 3,960 4,100 5,110 5,330 350 10,300 9,950 10,830 11,220 13,070 13,640 14,480 16,460 19,450
160 3,610 3,300 3,520 3,660 4,180 4,400 4,580 5,640 6,120 AM26 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 AM46 AM50 AM50 AM57 AM61 AM63 AM76 AM85
180 3,880 3,700 4,230 4,400 4,930 5,240 5,500 6,520 6,960 400 11,880 11,440 12,370 12,760 13,600 15,620 16,370 18,400 21,830 201~ 210 100 AM24 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 301~ 350 200 AM42 AM45 AM45 AM52 AM55 AM57 AM69 AM77
200 4,140 3,960 4,540 4,620 5,420 5,550 5,720 6,910 7,260
210 100 4,400 4,270 4,670 4,760 5,550 5,680 5,900 7,130 7,400 450 13,380 12,940 13,730 14,220 15,930 17,520 18,130 20,240 24,120 211~ 250 AM26 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 351~ 400 AM44 AM46 AM46 AM53 AM56 AM59 AM73 AM81
250 4,890 4,670 5,550 5,720 6,560 6,780 7,000 8,410 8,940 AM24 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 AM40 AM42 AM42 AM48 AM51 AM54 AM66 AM73
300 5,810 5,680 6,600 6,740 7,700 8,010 8,320 9,860 10,610 500 14,880 14,350 15,100 15,540 18,220 19,230 19,940 22,000 26,400
350 6,690 6,520 7,310 7,480 8,850 9,240 9,640 11,360 12,280 AM26 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 AM44 AM46 AM46 AM53 AM55 AM59 AM69 AM81
400 7,530 7,350 8,230 8,360 9,990 10,480 10,920 12,810 13,950 160 4,580 4,360 4,710 4,800 5,330 5,810 6,380 7,480 8,450 251~ 300 AM24 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 401~ 450 AM40 AM42 AM42 AM48 AM50 AM54 AM63 AM73
450 8,410 8,230 9,420 9,600 11,180 11,710 12,320 14,350 15,670
500 9,240 9,070 10,740 10,920 12,320 12,900 13,560 15,800 17,300 200 5,460 5,240 6,030 6,210 6,650 7,620 8,140 8,980 10,650 301~ 350 AM25 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 451~ 500 AM44 AM46 AM46 AM53 AM55 AM59 AM69 AM81
125 3,260 3,220 3,260 3,350 3,610 3,740 4,230 4,930 5,200 AM23 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 AM40 AM42 AM42 AM48 AM50 AM54 AM63 AM73
150 3,880 3,700 3,790 3,880 4,270 4,580 4,890 5,680 6,120 250 6,960 6,690 7,700 7,970 8,890 9,510 10,120 11,880 13,820
160 4,100 3,920 4,140 4,320 4,760 5,110 5,460 6,250 6,690 351~ 400 AM25 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 101~ 200 AM56 AM59 AM59 AM65 AM69 AM78 AM89 AM96
180 4,540 4,360 4,580 4,760 5,020 5,550 5,990 6,870 7,570 300 8,450 8,140 9,160 9,420 11,000 11,400 12,320 14,260 16,810 AM23 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 AM51 AM54 AM54 AM59 AM63 AM71 AM81 AM87
200 4,980 4,800 5,110 5,240 5,420 5,990 6,600 7,400 8,450 160
210 5,200 5,020 5,330 5,460 5,720 6,250 6,960 7,660 8,890 401~ 450 AM25 AM25 AM28 AM28 AM31 AM32 AM34 AM41 AM44 201~ 250 AM51 AM54 AM54 AM63 AM66 AM73 AM86 AM96
350 9,950 9,600 10,520 10,870 12,720 13,290 14,130 16,110 19,100 AM23 AM23 AM26 AM26 AM28 AM29 AM31 AM37 AM40 AM46 AM49 AM49 AM57 AM60 AM66 AM78 AM87
125
250 6,080 5,900 5,990 6,120 6,340 6,870 7,570 8,850 10,520 400 11,440 11,050 11,970 12,320 13,160 15,180 15,930 17,960 21,390 451~ 500 AM25 AM25 AM28 AM28 AM31 AM32 AM34 AM41 AM44 251~ 300 AM51 AM54 AM54 AM63 AM66 AM73 AM86 AM96
300 7,220 7,040 7,400 7,570 8,500 9,550 10,520 12,240 13,380 AM23 AM23 AM26 AM26 AM28 AM29 AM31 AM37 AM40 AM46 AM49 AM49 AM57 AM60 AM66 AM78 AM87
350 8,360 8,190 8,580 8,800 9,680 10,740 12,020 13,780 15,760 450 12,940 12,500 13,340 13,780 15,490 17,080 17,690 19,800 23,680
400 9,510 9,330 9,770 10,040 10,870 11,930 13,070 14,830 16,770 AM37 AM36 AM42 AM42 AM45 AM48 AM53 AM59 AM65 AM51 AM54 AM54 AM63 AM66 AM73 AM86 AM96
450 10,740 10,480 10,960 11,270 12,500 13,120 14,830 16,680 19,320 500 14,440 13,910 14,700 15,100 17,780 18,790 19,500 21,560 25,960 50~ 125 AM34 AM33 AM38 AM38 AM41 AM44 AM48 AM54 AM59 301~ 350 250 AM46 AM49 AM49 AM57 AM60 AM66 AM78 AM87
500 11,880 11,620 11,970 12,320 13,160 14,130 15,760 18,130 21,120
200 7,400 7,530 7,840 8,940 9,600 10,740 12,940 13,950 126~ 150 AM30 AM29 AM33 AM33 AM35 AM39 AM43 AM50 AM54 351~ 400 AM45 AM51 AM51 AM63 AM66 AM73 AM85 AM94
AM27 AM27 AM30 AM30 AM32 AM36 AM39 AM45 AM49 AM41 AM46 AM46 AM57 AM60 AM66 AM77 AM85
250 8,890 9,000 9,380 12,060 12,720 13,730 15,980 17,960
AM30 AM29 AM33 AM33 AM35 AM39 AM43 AM50 AM54 AM45 AM51 AM51 AM57 AM61 AM69 AM85 AM90
300 10,390 10,500 10,920 14,220 14,390 16,460 18,970 21,480 151~ 160 AM27 AM27 AM30 AM30 AM32 AM36 AM39 AM45 AM49 401~ 450 AM41 AM46 AM46 AM52 AM55 AM63 AM77 AM81
350 200 11,880 12,000 12,460 15,540 16,060 18,920 21,740 24,690 161~ 180 AM30 AM29 AM32 AM32 AM34 AM36 AM40 AM46 AM52 451~ 500 AM45 AM48 AM48 AM55 AM58 AM66 AM81 AM90
AM27 AM27 AM29 AM29 AM31 AM33 AM36 AM42 AM47 AM41 AM44 AM44 AM50 AM53 AM60 AM73 AM81
400 13,380 13,500 14,000 16,860 17,740 20,990 23,940 27,420
181~ 200 AM29 AM28 AM32 AM32 AM34 AM36 AM40 AM46 AM52 101~ 200 AM73 AM77 AM77 AM86 AM95 AM102 AM122 AM128
450 14,880 15,000 15,540 18,180 19,410 22,620 25,660 29,480 AM27 AM26 AM29 AM29 AM31 AM33 AM36 AM42 AM47 AM66 AM70 AM70 AM78 AM86 AM92 AM110 AM116
500 16,280 16,380 16,990 19,410 21,080 23,370 26,400 30,450 201~ 210 AM29 AM28 AM32 AM32 AM34 AM36 AM40 AM46 AM52 201~ 300 AM68 AM69 AM69 AM78 AM85 AM90 AM117 AM124
AM27 AM26 AM29 AM29 AM31 AM33 AM36 AM42 AM47 AM62 AM63 AM63 AM71 AM77 AM81 AM106 AM112
250 10,650 11,370 11,800 13,290 14,440 15,760 18,220 20,990 125
AM29 AM28 AM32 AM32 AM34 AM36 AM40 AM46 AM52 AM65 AM65 AM65 AM77 AM85 AM89 AM109 AM119
300 12,320 13,500 14,000 16,370 17,690 18,920 22,270 25,520 211~ 250 AM27 AM26 AM29 AM29 AM31 AM33 AM36 AM42 AM47 301~ 350 AM59 AM59 AM59 AM70 AM77 AM81 AM99 AM108
300 AM65 AM65 AM65 AM77 AM85 AM89 AM109 AM119
350 14,000 15,120 15,670 18,530 19,540 21,960 25,610 28,600 251~ 300 AM28 AM26 AM32 AM32 AM34 AM36 AM40 AM46 AM52 AM59 AM59 AM59 AM70 AM77 AM81 AM99 AM108
250 15,670 16,630 17,340 20,380 21,390 24,420 28,520 31,680 AM26 AM24 AM29 AM29 AM31 AM33 AM36 AM42 AM47 351~ 400
400 301~ 350 AM28 AM26 AM31 AM31 AM34 AM36 AM40 AM46 AM52 401~ 450 AM63 AM64 AM64 AM76 AM84 AM88 AM105 AM116
AM26 AM24 AM28 AM28 AM31 AM33 AM36 AM42 AM47 AM57 AM58 AM58 AM69 AM76 AM80 AM95 AM105
450 17,340 18,250 19,010 21,560 23,240 26,450 30,940 34,760
AM28 AM26 AM31 AM31 AM32 AM35 AM40 AM45 AM51 AM63 AM64 AM64 AM76 AM84 AM88 AM105 AM116
500 18,880 20,870 20,600 22,710 24,950 27,990 32,740 37,840 351~ 400 AM26 AM24 AM28 AM28 AM29 AM32 AM36 AM41 AM46 451~ 500 AM57 AM58 AM58 AM69 AM76 AM80 AM95 AM105
300 16,460 16,500 16,550 18,040 20,460 21,210 25,660 28,250 401~ 450 AM28 AM26 AM31 AM31 AM32 AM35 AM39 AM45 AM51
AM26 AM24 AM28 AM28 AM29 AM32 AM36 AM41 AM46
350 18,920 19,020 19,190 20,950 24,510 26,140 30,500 34,850
451~ 500 AM28 AM26 AM31 AM31 AM32 AM35 AM39 AM45 AM51
400 300 21,390 21,540 21,830 23,850 28,560 30,630 35,730 40,660 AM26 AM24 AM28 AM28 AM29 AM32 AM36 AM41 AM46
1159 450 24,290 24,350 24,470 26,760 32,610 34,590 40,310 45,760 1160
500 26,360 26,850 27,060 33,180 36,610 37,840 44,090 49,900 Express P.38 Press 2007 http://misumi.jp/press/ For inquiry, ordering and P.1269
service system other information, refer to
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES -DC- Heat treatment data P.1185
-STANDARDCSIZE SPECIFIEDCECONOMY TYPE-
DC (Standard type) Price calculation formula Upper : Size specified type Price calculation formula Upper : Size specified type
S-DC (Size specified type) (AMPrice coefficient) Lower : Economy type (AMPrice coefficient) Lower : Economy type
E-DC (Economy type)
AT 10 13 15 16 20 22 25 30 35 AT 10 13 15 16 20 22 25 30 35
A (1mm incr.)B (1mm incr.)B
Dimension tolerance
Precision standards P.1158 T Type 30~ 60 AM31 AM30 AM32 AM32 AM35 AM36 AM40 101~ 150 AM45 AM45 AM46 AM46 AM52 AM55 AM59 AM67 AM74
AM28 AM27 AM29 AM29 AM32 AM33 AM36 AM41 AM41 AM42 AM42 AM47 AM50 AM54 AM61 AM67
ACB T
99mm or less +0.4 61~ 80 AM25 AM24 AM25 AM25 AM29 AM30 AM34 151~ 180 AM45 AM45 AM46 AM46 AM52 AM55 AM59 AM67 AM74
0 AM23 AM22 AM23 AM23 AM27 AM27 AM31 AM41 AM41 AM42 AM42 AM47 AM50 AM54 AM61 AM67
B
DC Standard 100~250mm +0.5 +0.5 81~ 100 AM25 AM24 AM25 AM25 AM29 AM30 AM34 181~ 200 AM41 AM40 AM42 AM42 AM45 AM50 AM55 AM64 AM74
Size specified 0 +0.2 AM23 AM22 AM23 AM23 AM27 AM27 AM31 AM37 AM36 AM38 AM38 AM41 AM45 AM50 AM58 AM67
251mm or more +0.8 AM24 AM23 AM24 AM24 AM26 AM28 AM30 AM39 AM37 AM40 AM40 AM45 AM50 AM55 AM64 AM74
0 AM22 AM21 AM22 AM22 AM24 AM26 AM27 AM36 AM34 AM36 AM36 AM41 AM45 AM50 AM58 AM67
101~ 200 60 201~ 210
99mm or less +0.4
0
AM24 AM23 AM24 AM24 AM26 AM28 AM30 AM39 AM37 AM40 AM40 AM45 AM50 AM55 AM64 AM74
Economy 100~250mm +0.5 +0.6 201~ 300 AM22 AM21 AM22 AM22 AM24 AM26 AM27 211~ 250 AM36 AM34 AM36 AM36 AM41 AM45 AM50 AM58 AM67
0 +0.3 251~ 300 AM39 AM37 AM40 AM40 AM45 AM50 AM54 AM64 AM74
150 AM36 AM34 AM36 AM36 AM41 AM45 AM49 AM58 AM67
251mm or more +0.8 AM21 AM20 AM21 AM21 AM23 AM25 AM28
0 301~ 400 AM19 AM18 AM19 AM19 AM21 AM23 AM26
DC53(Raw material) 401~ 500 AM21 AM20 AM21 AM21 AM23 AM25 AM28 301~ 350 AM39 AM37 AM40 AM40 AM45 AM50 AM54 AM64 AM74
AM19 AM18 AM19 AM19 AM21 AM23 AM26 AM36 AM34 AM36 AM36 AM41 AM45 AM49 AM58 AM67
Catalog No. AB T IVolume discount rate P.37 To be quoted on 30~ 80 AM32 AM31 AM33 AM33 AM36 AM37 AM41 AM46 AM50 351~ 400 AM39 AM37 AM40 AM40 AM45 AM48 AM52 AM63 AM73
price & lead time AM29 AM28 AM30 AM30 AM33 AM34 AM37 AM42 AM45 AM36 AM34 AM36 AM36 AM41 AM44 AM47 AM57 AM66
DC 100 80 10 above Max. Q'ty.
Order S-DC 230 100 16 Price Quantity 1~9 10~30 81~ 100 AM25 AM25 AM25 AM25 AM30 AM32 AM33 AM40 AM43 401~ 450 AM39 AM37 AM40 AM40 AM45 AM48 AM52 AM63 AM73
E-DC 365 250 13 AM23 AM23 AM23 AM23 AM27 AM29 AM30 AM36 AM39 AM36 AM34 AM36 AM36 AM41 AM44 AM47 AM57 AM66
Rate - 5%
A(dimension A)MPrice coefficient=Unit price 101~ 125 AM24 AM23 AM25 AM25 AM29 AM30 AM32 AM40 AM43 451~ 500 AM39 AM37 AM40 AM40 AM45 AM48 AM52 AM63 AM73
(ex)S-DC-230-100-16 AM22 AM21 AM23 AM23 AM27 AM27 AM29 AM36 AM39 AM36 AM34 AM36 AM36 AM41 AM44 AM47 AM57 AM66
3Delivery 126~ 150 AM24 AM23 AM25 AM25 AM29 AM30 AM32 AM40 AM43 101~ 160 AM44 AM43 AM45 AM45 AM51 AM54 AM58 AM65 AM73
151~ 160 AM40 AM39 AM41 AM41 AM46 AM49 AM53 AM59 AM66
Days 230 M 28 =\6,440 80 AM22 AM21 AM23 AM23 AM27 AM27 AM29 AM36 AM39
AM24 AM23 AM25 AM25 AM29 AM30 AM32 AM40 AM43
161~ 200 AM39 AM37 AM41 AM41 AM45 AM48 AM54 AM63 AM73
P.1174(B and T dimension changeable) AM22 AM21 AM23 AM23 AM27 AM27 AM29 AM36 AM39 AM36 AM34 AM37 AM37 AM41 AM44 AM49 AM57 AM66
Express A 800/1Pc. P.38 Alterations are available for size specified and economy type.
Alteration 161~ 200 AM24 AM23 AM25 AM25 AM29 AM30 AM32 AM40 AM43 201~ 250 AM36 AM35 AM41 AM41 AM45 AM48 AM54 AM63 AM73
AM22 AM21 AM23 AM23 AM27 AM27 AM29 AM36 AM39 AM33 AM32 AM37 AM37 AM41 AM44 AM49 AM57 AM66
A flat charge of 2,160 yen for 3 pieces or more of the same size.
AM24 AM22 AM25 AM25 AM25 AM28 AM30 AM35 AM40 AM36 AM35 AM41 AM41 AM45 AM48 AM52 AM63 AM73
201~ 250 AM22 AM20 AM23 AM23 AM23 AM26 AM27 AM32 AM36 251~ 300 AM33 AM32 AM37 AM37 AM41 AM44 AM47 AM57 AM66
301~ 350 AM36 AM35 AM40 AM40 AM45 AM48 AM52 AM63 AM73
U/Price(Standard type) U/Price(Standard type) AM24 AM22 AM25 AM25 AM25 AM28 AM30 AM33 AM37 160 AM33 AM32 AM36 AM36 AM41 AM44 AM47 AM57 AM66
A B T 10 13 15 16 20 22 25 30 35 AM22 AM20 AM23 AM23 AM23 AM26 AM27 AM30 AM34
60 1,320 1,190 1,240 1,280 1,460 1,500 1,760 A B T 10 13 15 16 20 22 25 30 35 251~ 500
80 60 1,540 1,460 1,500 1,540 1,720 1,810 2,120
500 7,880 7,220 8,060 8,100 9,020 10,340 11,220 150 4,670 4,450 4,800 4,890 5,420 5,900 6,470 7,570 8,540 30~ 100 AM33 AM32 AM34 AM34 AM40 AM42 AM45 AM52 AM55 351~ 400 AM36 AM35 AM39 AM39 AM44 AM47 AM51 AM62 AM72
80 1,810 1,630 1,720 1,760 1,980 2,070 2,160 2,600 2,730 AM30 AM29 AM31 AM31 AM36 AM38 AM41 AM47 AM50 AM33 AM32 AM36 AM36 AM40 AM43 AM46 AM56 AM65
100 2,120 1,900 1,980 2,030 2,290 2,380 2,560 3,000 3,130
125 2,420 2,200 2,380 2,420 2,690 2,860 3,000 3,480 3,700 180 5,280 5,020 5,640 5,770 6,250 7,000 7,570 8,540 9,900 101~ 125 AM28 AM26 AM29 AM29 AM33 AM35 AM35 AM45 AM47 401~ 450 AM36 AM35 AM39 AM39 AM44 AM47 AM51 AM62 AM72
150 3,000 2,780 3,040 3,130 3,610 3,830 4,140 4,620 5,280 AM26 AM24 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM33 AM32 AM36 AM36 AM40 AM43 AM46 AM56 AM65
160 80 3,170 2,860 3,130 3,220 3,700 3,920 4,230 4,710 5,460 200 5,720 5,500 6,300 6,470 6,910 7,880 8,410 9,240 10,920
200 3,570 3,350 3,880 3,920 4,360 4,580 4,890 5,640 6,520 AM26 AM25 AM29 AM29 AM33 AM35 AM35 AM45 AM47 AM36 AM35 AM39 AM39 AM44 AM47 AM51 AM62 AM72
250 4,140 3,960 4,710 4,800 5,200 5,550 5,860 6,600 7,750 210 6,080 5,810 6,600 6,820 7,400 8,280 8,850 9,860 11,580 126~ 150 AM24 AM23 AM27 AM27 AM30 AM32 AM32 AM41 AM43 451~ 500 AM33 AM32 AM36 AM36 AM40 AM43 AM46 AM56 AM65
500 7,880 7,750 9,160 9,290 9,460 10,920 11,580 13,160 15,400
100 2,380 2,290 2,380 2,420 2,690 2,860 3,000 3,480 3,700 250 7,310 7,040 8,010 8,320 9,240 9,860 10,480 12,240 14,170 151~ 160 AM26 AM25 AM29 AM29 AM33 AM35 AM35 AM45 AM47 101~ 200 AM55 AM57 AM57 AM62 AM65 AM70 AM83 AM85
125 2,950 2,690 2,820 2,910 3,300 3,390 3,520 4,490 4,800 300 150 8,800 8,500 9,510 9,770 11,360 11,750 12,680 14,610 17,160 AM24 AM23 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM50 AM52 AM52 AM56 AM59 AM63 AM75 AM77
150 3,390 3,080 3,170 3,300 3,740 3,960 4,100 5,110 5,330
160 3,610 3,300 3,520 3,660 4,180 4,400 4,580 5,640 6,120 350 10,300 9,950 10,830 11,220 13,070 13,640 14,480 16,460 19,450 161~ 180 AM26 AM25 AM29 AM29 AM33 AM35 AM35 AM45 AM47 201~ 250 AM50 AM53 AM53 AM59 AM61 AM66 AM76 AM85
180 3,880 3,700 4,230 4,400 4,930 5,240 5,500 6,520 6,960 AM24 AM23 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM45 AM48 AM48 AM54 AM55 AM60 AM69 AM77
200 4,140 3,960 4,540 4,620 5,420 5,550 5,720 6,910 7,260
210 100 4,400 4,270 4,670 4,760 5,550 5,680 5,900 7,130 7,400 400 11,880 11,440 12,370 12,760 13,600 15,620 16,370 18,400 21,830 181~ 200 AM26 AM25 AM29 AM29 AM33 AM35 AM35 AM45 AM47 251~ 300 AM50 AM53 AM53 AM59 AM61 AM66 AM76 AM85
250 4,890 4,670 5,550 5,720 6,560 6,780 7,000 8,410 8,940 AM24 AM23 AM27 AM27 AM30 AM32 AM32 AM41 AM43 AM45 AM48 AM48 AM54 AM55 AM60 AM69 AM77
300 5,810 5,680 6,600 6,740 7,700 8,010 8,320 9,860 10,610 450 13,380 12,940 13,730 14,220 15,930 17,520 18,130 20,240 24,120
350 6,690 6,520 7,310 7,480 8,850 9,240 9,640 11,360 12,280 201~ 210 100 AM26 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 301~ 350 200 AM46 AM50 AM50 AM57 AM61 AM66 AM76 AM85
400 7,530 7,350 8,230 8,360 9,990 10,480 10,920 12,810 13,950 500 14,880 14,350 15,100 15,540 18,220 19,230 19,940 22,000 26,400 AM24 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 AM42 AM45 AM45 AM52 AM55 AM60 AM69 AM77
450 8,410 8,230 9,420 9,600 11,180 11,710 12,320 14,350 15,670
500 9,240 9,070 10,740 10,920 12,320 12,900 13,560 15,800 17,300 160 4,580 4,360 4,710 4,800 5,330 5,810 6,380 7,480 8,450 211~ 250 AM26 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 351~ 400 AM44 AM46 AM46 AM53 AM56 AM63 AM73 AM81
125 3,260 3,220 3,260 3,350 3,610 3,740 4,230 4,930 5,200 AM24 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 AM40 AM42 AM42 AM48 AM51 AM57 AM66 AM73
150 3,880 3,700 3,790 3,880 4,270 4,580 4,890 5,680 6,120
160 4,100 3,920 4,140 4,320 4,760 5,110 5,460 6,250 6,690 200 5,460 5,240 6,030 6,210 6,650 7,620 8,140 8,980 10,650 251~ 300 AM26 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 401~ 450 AM44 AM46 AM46 AM53 AM55 AM59 AM69 AM81
180 4,540 4,360 4,580 4,760 5,020 5,550 5,990 6,870 7,570 AM24 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 AM40 AM42 AM42 AM48 AM50 AM54 AM63 AM73
200 4,980 4,800 5,110 5,240 5,420 5,990 6,600 7,400 8,450 250 6,960 6,690 7,700 7,970 8,890 9,510 10,120 11,880 13,820
210 5,200 5,020 5,330 5,460 5,720 6,250 6,960 7,660 8,890 AM25 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 AM44 AM46 AM46 AM53 AM55 AM59 AM69 AM81
250 125 6,080 5,900 5,990 6,120 6,340 6,870 7,570 8,850 10,520 300 8,450 8,140 9,160 9,420 11,000 11,400 12,320 14,260 16,810 301~ 350 AM23 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 451~ 500 AM40 AM42 AM42 AM48 AM50 AM54 AM63 AM73
300 7,220 7,040 7,400 7,570 8,500 9,550 10,520 12,240 13,380 350 160 9,950 9,600 10,520 10,870 12,720 13,290 14,130 16,110 19,100
350 8,360 8,190 8,580 8,800 9,680 10,740 12,020 13,780 15,760 351~ 400 AM25 AM25 AM28 AM28 AM32 AM33 AM34 AM43 AM45 101~ 200 AM56 AM59 AM59 AM65 AM69 AM78 AM89 AM96
400 9,510 9,330 9,770 10,040 10,870 11,930 13,070 14,830 16,770 AM23 AM23 AM26 AM26 AM29 AM30 AM31 AM39 AM41 AM51 AM54 AM54 AM59 AM63 AM71 AM81 AM87
450 10,740 10,480 10,960 11,270 12,500 13,120 14,830 16,680 19,320 400 11,440 11,050 11,970 12,320 13,160 15,180 15,930 17,960 21,390
500 11,880 11,620 11,970 12,320 13,160 14,130 15,760 18,130 21,120 401~ 450 AM25 AM25 AM28 AM28 AM31 AM32 AM34 AM41 AM44 201~ 250 AM51 AM54 AM54 AM63 AM66 AM73 AM86 AM96
450 12,940 12,500 13,340 13,780 15,490 17,080 17,690 19,800 23,680 AM23 AM23 AM26 AM26 AM28 AM29 AM31 AM37 AM40 AM46 AM49 AM49 AM57 AM60 AM66 AM78 AM87
500 14,440 13,910 14,700 15,100 17,780 18,790 19,500 21,560 25,960 451~ 500 AM25 AM25 AM28 AM28 AM31 AM32 AM34 AM41 AM44 251~ 300 AM51 AM54 AM54 AM63 AM66 AM73 AM86 AM96
AM23 AM23 AM26 AM26 AM28 AM29 AM31 AM37 AM40 AM46 AM49 AM49 AM57 AM60 AM66 AM78 AM87
200 7,400 7,530 7,840 8,940 9,600 10,740 12,940 13,950
50~ 125 AM37 AM36 AM42 AM42 AM45 AM48 AM53 AM59 AM65 301~ 350 250 AM51 AM54 AM54 AM63 AM66 AM73 AM86 AM96
250 8,890 9,000 9,380 12,060 12,720 13,730 15,980 17,960 AM34 AM33 AM38 AM38 AM41 AM44 AM48 AM54 AM59 AM46 AM49 AM49 AM57 AM60 AM66 AM78 AM87
300 10,390 10,500 10,920 14,220 14,390 16,460 18,970 21,480 126~ 150 AM30 AM29 AM33 AM33 AM35 AM39 AM43 AM50 AM54 351~ 400 AM45 AM51 AM51 AM63 AM66 AM73 AM85 AM94
AM27 AM27 AM30 AM30 AM32 AM36 AM39 AM45 AM49 AM41 AM46 AM46 AM57 AM60 AM66 AM77 AM85
350 200 11,880 12,000 12,460 15,540 16,060 18,920 21,740 24,690 151~ 160 AM30 AM29 AM33 AM33 AM35 AM39 AM43 AM50 AM54 401~ 450 AM45 AM51 AM51 AM57 AM61 AM69 AM85 AM90
AM27 AM27 AM30 AM30 AM32 AM36 AM39 AM45 AM49 AM41 AM46 AM46 AM52 AM55 AM63 AM77 AM81
400 13,380 13,500 14,000 16,860 17,740 20,990 23,940 27,420
AM30 AM29 AM32 AM32 AM34 AM36 AM40 AM46 AM52 AM45 AM46 AM48 AM55 AM58 AM66 AM81 AM90
450 14,880 15,000 15,540 18,180 19,410 22,620 25,660 29,480 161~ 180 AM27 AM27 AM29 AM29 AM31 AM33 AM36 AM42 AM47 451~ 500 AM41 AM42 AM44 AM50 AM53 AM60 AM73 AM81
500 16,280 16,380 16,990 19,410 21,080 23,370 26,400 30,450 181~ 200 AM29 AM28 AM32 AM32 AM34 AM36 AM40 AM46 AM52 101~ 200 AM73 AM77 AM77 AM86 AM95 AM102 AM122 AM128
AM27 AM26 AM29 AM29 AM31 AM33 AM36 AM42 AM47 AM66 AM70 AM70 AM78 AM86 AM92 AM110 AM116
250 10,650 11,370 11,800 13,290 14,440 15,760 18,220 20,990
201~ 210 AM29 AM28 AM32 AM32 AM34 AM36 AM40 AM46 AM52 201~ 300 AM68 AM69 AM69 AM78 AM85 AM90 AM117 AM124
300 12,320 13,500 14,000 16,370 17,690 18,920 22,270 25,520 211~ 250 AM27 AM26 AM29 AM29 AM31 AM33 AM36 AM42 AM47 AM62 AM63 AM63 AM71 AM77 AM81 AM106 AM112
125 AM29 AM28 AM32 AM32 AM34 AM36 AM40 AM46 AM52
350 14,000 15,120 15,670 18,530 19,540 21,960 25,610 28,600 AM27 AM26 AM29 AM29 AM31 AM33 AM36 AM42 AM47 AM65 AM65 AM65 AM77 AM85 AM89 AM109 AM119
250 15,670 16,630 17,340 20,380 21,390 24,420 28,520 31,680 301~ 350 AM59 AM59 AM59 AM70 AM77 AM81 AM99 AM108
251~ 300 AM28 AM26 AM32 AM32 AM34 AM36 AM40 AM46 AM52 300 AM65 AM65 AM65 AM77 AM85 AM89 AM109 AM119
400 AM26 AM24 AM29 AM29 AM31 AM33 AM36 AM42 AM47 AM59 AM59 AM59 AM70 AM77 AM81 AM99 AM108
351~ 400
450 17,340 18,250 19,010 21,560 23,240 26,450 30,940 34,760
AM28 AM26 AM31 AM31 AM34 AM36 AM40 AM46 AM52 AM63 AM64 AM64 AM76 AM84 AM88 AM105 AM116
500 18,880 20,870 20,600 22,710 24,950 27,990 32,740 37,840 301~ 350 AM26 AM24 AM28 AM28 AM31 AM33 AM36 AM42 AM47 401~ 450 AM57 AM58 AM58 AM69 AM76 AM80 AM95 AM105
300 16,460 16,500 16,550 18,040 20,460 21,210 25,660 28,250 351~ 400 AM28 AM26 AM31 AM31 AM32 AM35 AM40 AM45 AM51 451~ 500 AM63 AM64 AM64 AM76 AM84 AM88 AM105 AM116
AM26 AM24 AM28 AM28 AM29 AM32 AM36 AM41 AM46 AM57 AM58 AM58 AM69 AM76 AM80 AM95 AM105
350 18,920 19,020 19,190 20,950 24,510 26,140 30,500 34,850
AM28 AM26 AM31 AM31 AM32 AM35 AM39 AM45 AM51
400 300 21,390 21,540 21,830 23,850 28,560 30,630 35,730 40,660 401~ 450 AM26 AM24 AM28 AM28 AM29 AM32 AM36 AM41 AM46
450 24,290 24,350 24,470 26,760 32,610 34,590 40,310 45,760 451~ 500 AM28 AM26 AM31 AM31 AM32 AM35 AM39 AM45 AM51
AM26 AM24 AM28 AM28 AM29 AM32 AM36 AM41 AM46
500 26,360 26,850 27,060 33,180 36,610 37,840 44,090 49,900
1161 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1162
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES -SKS- Heat treatment data P.1186
-STANDARDCSIZE SPECIFIEDCECONOMY TYPE-
SKS (Standard type) Price calculation formula Upper : Size specified type Price calculation formula Upper : Size specified type
S-SKS (Size specified type) (AMPrice coefficient) Lower : Economy type (AMPrice coefficient) Lower : Economy type
E-SKS (Economy type)
AT 8 10 13 15 16 20 22 25 30 35 40 50 AT 8 10 13 15 16 20 22 25 30 35 40 50
A (1mm incr.)B (1mm incr.)B
Precision standards P.1158 T Type Dimension tolerance 25~100 AM14 AM15 101~150 AM33 AM31 AM36 AM36 AM41 AM45 AM48 AM56 AM63 AM68 AM84
101~250 151~180 AM30 AM28 AM32 AM32 AM37 AM41 AM43 AM50 AM57 AM61 AM76
ACB T 25 AM13 AM14 181~200 AM33 AM31 AM36 AM36 AM41 AM45 AM48 AM56 AM63 AM68 AM84
AM10 AM11 201~210 AM30 AM28 AM32 AM32 AM37 AM41 AM43 AM50 AM57 AM61 AM76
99mm or less +0.4 211~250 AM30 AM29 AM34 AM34 AM37 AM41 AM45 AM53 AM57 AM65 AM79
B 0 AM 9 AM10 AM27 AM26 AM31 AM31 AM33 AM37 AM41 AM48 AM51 AM59 AM71
SKS 150 AM30 AM29 AM34 AM34 AM37 AM41 AM45 AM53 AM57 AM65 AM79
Standard 100~250mm +0.5 +0.5 30~100 AM17 AM18 251~300 AM27 AM26 AM31 AM31 AM33 AM37 AM41 AM48 AM51 AM59 AM71
Size specified 0 +0.2 AM15 AM16 301~350 AM30 AM29 AM34 AM34 AM37 AM41 AM45 AM53 AM57 AM65 AM79
351~400 AM27 AM26 AM31 AM31 AM33 AM37 AM41 AM48 AM51 AM59 AM71
251mm or more +0.8 101~200 40 AM13 AM14 401~450 AM29 AM28 AM32 AM32 AM35 AM39 AM43 AM50 AM55 AM62 AM76
0 AM12 AM13 451~500 AM26 AM25 AM29 AM29 AM32 AM35 AM39 AM45 AM50 AM56 AM68
101~160 AM29 AM28 AM30 AM30 AM34 AM36 AM41 AM46 AM52 AM58 AM74
99mm or less +0.4 201~400 AM11 AM12 161~200 AM26 AM25 AM27 AM27 AM31 AM32 AM37 AM41 AM47 AM52 AM67
0 AM10 AM11 201~250 AM28 AM28 AM30 AM30 AM34 AM36 AM41 AM46 AM52 AM58 AM74
251~300 AM25 AM25 AM27 AM27 AM31 AM32 AM37 AM41 AM47 AM52 AM67
Economy 100~250mm +0.5 +0.6 30~ 60 AM25 AM25 AM25 AM25 AM25 AM28 AM29 AM30 AM28 AM25 AM30 AM30 AM34 AM36 AM41 AM46 AM52 AM58 AM74
0 +0.3 AM23 AM23 AM23 AM23 AM23 AM25 AM26 AM27 160 AM25 AM23 AM27 AM27 AM31 AM32 AM37 AM41 AM47 AM52 AM67
301~350 AM25 AM25 AM30 AM30 AM34 AM36 AM41 AM46 AM52 AM58 AM74
251mm or more +0.8 AM23 AM25 AM22 AM23 AM23 AM24 AM25 AM25 351~400 AM23 AM23 AM27 AM27 AM31 AM32 AM37 AM41 AM47 AM52 AM67
0 AM21 AM23 AM20 AM21 AM21 AM22 AM23 AM23 401~450 AM32 AM30 AM35 AM35 AM40 AM44 AM47 AM55 AM61 AM67 AM83
61~ 80 451~500 AM29 AM27 AM32 AM32 AM36 AM40 AM42 AM50 AM55 AM60 AM75
SKS3(Raw material) 101~200 AM29 AM28 AM33 AM33 AM36 AM40 AM44 AM52 AM56 AM64 AM78
AM23 AM25 AM22 AM23 AM23 AM24 AM25 AM25 201~250 AM26 AM25 AM30 AM30 AM32 AM36 AM40 AM47 AM50 AM58 AM70
81~100 AM21 AM23 AM20 AM21 AM21 AM22 AM23 AM23 251~300 AM29 AM28 AM33 AM33 AM36 AM40 AM44 AM52 AM56 AM64 AM78
301~350 200 AM26 AM25 AM30 AM30 AM32 AM36 AM40 AM47 AM50 AM58 AM70
Catalog No. ABT IVolume discount rate P.37 To be quoted on 101~200 60 AM15 AM18 AM17 AM20 AM20 AM21 AM22 AM25 351~400 AM26 AM25 AM31 AM31 AM35 AM37 AM42 AM48 AM54 AM61 AM75
price & lead time AM14 AM16 AM15 AM18 AM18 AM19 AM20 AM23 401~450 AM23 AM23 AM28 AM28 AM32 AM33 AM38 AM43 AM49 AM55 AM68
Order SKS 500 200 25 Price Quantity 1~9 10~30 above Max. Q'ty. 451~500 AM26 AM25 AM29 AM29 AM33 AM35 AM40 AM45 AM51 AM57 AM73
S-SKS 320 250 40 201~300 AM15 AM18 AM17 AM20 AM20 AM21 AM22 AM25 101~200 AM23 AM23 AM26 AM26 AM30 AM32 AM36 AM41 AM46 AM51 AM66
E-SKS 365 250 20 Rate - 5% AM14 AM16 AM15 AM18 AM18 AM19 AM20 AM23 201~250 AM25 AM25 AM29 AM29 AM33 AM35 AM40 AM45 AM51 AM57 AM73
251~300 AM23 AM23 AM26 AM26 AM30 AM32 AM36 AM41 AM46 AM51 AM66
A(dimension A)MPrice coefficient=Unit price 301~400 AM15 AM18 AM17 AM20 AM20 AM21 AM22 AM25 301~350 250 AM25 AM24 AM29 AM29 AM33 AM35 AM40 AM45 AM51 AM57 AM73
AM14 AM16 AM15 AM18 AM18 AM19 AM20 AM23 351~400 AM23 AM22 AM26 AM26 AM30 AM32 AM36 AM41 AM46 AM51 AM66
(ex)S-SKS-320-100-30 401~450 AM25 AM24 AM29 AM29 AM33 AM35 AM40 AM45 AM51 AM57 AM73
401~500 AM15 AM15 AM15 AM19 AM19 AM20 AM21 AM24 451~500 AM23 AM22 AM26 AM26 AM30 AM32 AM36 AM41 AM46 AM51 AM66
3Delivery Days 320 M 32 =\10,240 AM14 AM14 AM14 AM17 AM17 AM18 AM19 AM22 101~200 AM40 AM39 AM43 AM43 AM47 AM51 AM56 AM64 AM70 AM79 AM97
201~300 AM36 AM35 AM39 AM39 AM42 AM46 AM50 AM58 AM63 AM71 AM87
P.1174(B and T dimension changeable) 30~ 80 AM25 AM28 AM25 AM26 AM26 AM28 AM31 AM33 AM36 AM41 301~350 AM35 AM35 AM39 AM39 AM43 AM45 AM51 AM57 AM65 AM74 AM94
Alterations are available for size specified and economy type. AM23 AM25 AM23 AM23 AM23 AM25 AM28 AM30 AM32 AM37 AM32 AM32 AM35 AM35 AM39 AM41 AM46 AM51 AM59 AM67 AM85
Alteration 300 AM35 AM35 AM39 AM39 AM43 AM45 AM51 AM57 AM65 AM74 AM94
Express A 800/1Pc. P.38 81~100 AM22 AM24 AM22 AM23 AM23 AM24 AM25 AM28 AM32 AM35 351~400 AM32 AM32 AM35 AM35 AM39 AM41 AM46 AM51 AM59 AM67 AM85
AM20 AM22 AM20 AM21 AM21 AM22 AM23 AM25 AM29 AM32 401~450 AM33 AM32 AM35 AM35 AM39 AM43 AM46 AM55 AM65 AM70 AM90
451~500 AM30 AM29 AM32 AM32 AM35 AM39 AM41 AM50 AM59 AM63 AM81
A flat charge of 2,160 yen for 3 pieces or more of the same size. 101~125 AM18 AM19 AM18 AM21 AM21 AM22 AM23 AM25 AM30 AM34 AM33 AM32 AM35 AM35 AM39 AM43 AM46 AM55 AM65 AM70 AM90
U/Price (Standard type) AM16 AM17 AM16 AM19 AM19 AM20 AM21 AM23 AM27 AM31 AM30 AM29 AM32 AM32 AM35 AM39 AM41 AM50 AM59 AM63 AM81
U/Price (Standard type) AM32 AM31 AM35 AM35 AM37 AM42 AM45 AM53 AM59 AM68 AM88
A B T 8 10 13 15 16 20 22 25 30 35 40 50 126~150 AM18 AM19 AM18 AM21 AM21 AM22 AM23 AM25 AM30 AM34 AM29 AM28 AM32 AM32 AM33 AM38 AM41 AM48 AM53 AM61 AM79
250 25 1,760 1,940 151~160 AM32 AM31 AM35 AM35 AM37 AM42 AM45 AM53 AM59 AM68 AM88
400 40 3,080 3,390 A B T 8 10 13 15 16 20 22 25 30 35 40 50 80 AM16 AM17 AM16 AM19 AM19 AM20 AM21 AM23 AM27 AM31 AM29 AM28 AM32 AM32 AM33 AM38 AM41 AM48 AM53 AM61 AM79
60 1,190 1,280 1,100 1,190 1,190 1,190 1,280 1,370 150 3,790 3,610 3,920 4,010 4,360 4,670 4,980 6,210 6,870 8,910 10,720 AM18 AM19 AM18 AM21 AM21 AM22 AM23 AM25 AM30 AM34 AM42 AM41 AM46 AM46 AM51 AM55 AM64 AM75 AM85 AM94 AM117
80 60 1,320 1,410 1,240 1,320 1,320 1,410 1,500 1,630 AM38 AM37 AM41 AM41 AM46 AM50 AM58 AM68 AM77 AM85 AM105
500 5,640 6,250 5,810 6,870 6,870 7,130 7,750 8,630 AM16 AM17 AM16 AM19 AM19 AM20 AM21 AM23 AM27 AM31 AM39 AM37 AM42 AM42 AM47 AM52 AM57 AM67 AM77 AM86 AM111
80 1,410 1,540 1,370 1,500 1,500 1,590 1,720 1,850 2,030 2,340 AM35 AM33 AM38 AM38 AM42 AM47 AM51 AM60 AM69 AM77 AM100
100 1,500 1,590 1,500 1,760 1,760 1,810 1,940 2,120 2,200 2,780 180 4,400 4,180 4,490 4,580 5,060 5,550 5,990 7,090 7,920 9,930 11,840 161~200 AM18 AM19 AM18 AM21 AM21 AM22 AM23 AM25 AM30 AM34 AM39 AM37 AM42 AM42 AM47 AM52 AM57 AM67 AM77 AM86 AM111
125 1,850 1,980 1,760 1,900 1,940 2,120 2,290 2,470 2,780 3,000 AM16 AM17 AM16 AM19 AM19 AM20 AM21 AM23 AM27 AM31 AM35 AM33 AM38 AM38 AM42 AM47 AM51 AM60 AM69 AM77 AM100
150 2,340 2,510 2,340 2,470 2,510 2,860 3,040 3,300 3,700 3,960 200 4,710 4,450 4,760 4,840 5,420 6,030 6,600 7,570 8,500 11,010 13,360 AM39 AM37 AM42 AM42 AM47 AM52 AM57 AM67 AM77 AM86 AM111
201~250 AM18 AM19 AM18 AM21 AM21 AM22 AM23 AM25 AM30 AM34 AM35 AM33 AM38 AM38 AM42 AM47 AM51 AM60 AM69 AM77 AM100
80 AM16 AM17 AM16 AM19 AM19 AM20 AM21 AM23 AM27 AM31 AM37 AM36 AM42 AM42 AM46 AM51 AM57 AM67 AM77 AM86 AM111
160 2,510 2,640 2,510 2,640 2,730 3,040 3,220 3,570 4,010 4,270 210 5,020 4,710 4,980 5,150 5,770 6,430 7,000 8,060 9,020 12,420 14,980 AM33 AM32 AM38 AM38 AM41 AM46 AM51 AM60 AM69 AM77 AM100
200 3,080 3,260 2,860 3,130 3,130 3,570 4,010 4,360 4,620 5,110 251~500 AM18 AM19 AM18 AM21 AM21 AM22 AM23 AM25 AM30 AM34 AM35 AM35 AM40 AM40 AM46 AM51 AM55 AM65 AM73 AM81 AM99
250 3,790 4,100 3,660 3,960 4,050 4,360 4,760 5,110 5,770 6,600 250 6,120 5,770 6,080 6,250 7,090 7,840 8,580 9,860 11,000 13,320 16,170 AM16 AM17 AM16 AM19 AM19 AM20 AM21 AM23 AM27 AM31 AM32 AM32 AM36 AM36 AM41 AM46 AM50 AM59 AM66 AM73 AM89
500 6,560 7,180 6,780 7,920 7,970 8,140 8,760 9,640 11,530 12,320 150 7,400 7,000 7,480 7,660 8,580 9,460 10,300 11,880 13,420 15,050 18,740 AM35 AM35 AM37 AM37 AM44 AM47 AM54 AM63 AM70 AM79 AM99
100 1,900 1,980 1,760 1,900 1,940 2,120 2,290 2,470 2,780 3,000 30~100 AM28 AM29 AM26 AM30 AM30 AM33 AM35 AM37 AM41 AM44 AM32 AM32 AM33 AM33 AM40 AM42 AM49 AM57 AM63 AM71 AM89
125 2,200 2,250 2,070 2,200 2,250 2,470 2,640 2,910 3,440 3,830 300 AM25 AM26 AM23 AM27 AM27 AM30 AM32 AM33 AM37 AM40
150 2,470 2,510 2,290 2,470 2,510 2,860 3,040 3,350 4,140 4,540 AM65 AM75 AM79 AM85 AM95 AM119 AM121 AM144
160 2,600 2,780 2,510 2,780 2,860 3,130 3,350 3,700 4,360 4,930 350 8,320 8,060 8,720 8,940 9,990 10,960 11,880 13,780 15,490 17,180 21,570 101~125 AM24 AM25 AM23 AM25 AM25 AM28 AM30 AM32 AM35 AM37 AM59 AM68 AM71 AM77 AM86 AM107 AM109 AM130
180 3,080 3,080 2,780 2,950 3,040 3,480 3,700 4,100 4,760 5,240 AM22 AM23 AM21 AM23 AM23 AM25 AM27 AM29 AM32 AM33 AM61 AM68 AM73 AM77 AM89 AM116 AM119 AM135
200 3,350 3,390 3,040 3,350 3,350 3,740 4,140 4,450 5,150 5,550 400 9,330 8,800 9,330 9,550 10,700 11,880 13,070 15,100 16,940 19,500 24,730 AM55 AM61 AM66 AM69 AM80 AM104 AM107 AM122
210 100 3,480 3,480 3,130 3,390 3,440 3,830 4,270 4,620 5,460 5,990 126~150 AM23 AM24 AM22 AM25 AM25 AM25 AM28 AM30 AM33 AM35 AM57 AM65 AM69 AM76 AM85 AM112 AM116 AM135
250 4,400 4,540 4,050 4,540 4,620 5,110 5,500 6,030 6,910 7,350 450 10,260 9,820 10,830 11,140 12,370 13,470 14,520 16,860 19,320 21,620 27,150 AM21 AM22 AM20 AM23 AM23 AM23 AM25 AM27 AM30 AM32 AM51 AM59 AM62 AM68 AM77 AM101 AM104 AM122
300 5,020 5,420 4,710 5,200 5,240 5,940 6,470 7,000 8,230 8,630 AM57 AM65 AM69 AM76 AM85 AM112 AM115 AM135
350 5,640 6,340 5,940 6,470 6,600 7,260 7,440 8,540 9,680 10,170 500 11,050 10,390 11,620 11,840 13,160 14,260 15,360 17,870 20,600 23,910 30,010 151~160 AM23 AM24 AM22 AM25 AM25 AM25 AM28 AM30 AM33 AM35 AM51 AM59 AM62 AM68 AM77 AM101 AM104 AM122
400 6,250 7,130 6,080 6,690 6,740 7,480 8,410 8,940 10,260 11,180 AM21 AM22 AM20 AM23 AM23 AM23 AM25 AM27 AM30 AM32 AM56 AM65 AM68 AM74 AM84 AM109 AM110 AM125
450 7,000 8,010 7,040 7,750 7,840 8,630 9,380 10,210 11,440 12,460 AM50 AM59 AM61 AM67 AM76 AM98 AM99 AM113
500 7,750 8,890 8,010 8,670 8,760 9,510 10,170 11,140 12,410 13,560 160 3,700 3,520 3,880 3,920 4,270 4,580 4,890 6,120 6,780 8,720 10,560 161~180 AM23 AM24 AM22 AM25 AM25 AM25 AM28 AM30 AM33 AM35 AM56 AM65 AM68 AM74 AM84 AM109 AM110 AM125
125 2,510 2,560 2,380 2,470 2,560 2,910 3,130 3,390 4,050 4,360 5,720 7,040 AM21 AM22 AM20 AM23 AM23 AM23 AM25 AM27 AM30 AM32 AM50 AM59 AM61 AM67 AM76 AM98 AM99 AM113
150 2,860 2,910 2,640 2,860 2,950 3,350 3,610 3,920 4,670 5,200 6,160 7,570 200 4,450 4,180 4,490 4,580 5,150 5,770 6,340 7,310 8,230 10,650 12,980
160 3,080 3,220 2,860 3,350 3,480 3,880 4,180 4,540 5,110 5,640 6,520 8,010 181~200 AM23 AM24 AM22 AM25 AM25 AM25 AM28 AM30 AM33 AM35
180 3,520 3,570 3,000 3,390 3,520 4,050 4,320 4,670 5,330 6,030 7,220 8,890 AM21 AM22 AM20 AM23 AM23 AM23 AM25 AM27 AM30 AM32
200 3,880 3,920 3,480 3,880 3,920 4,400 4,710 5,240 6,080 6,600 7,920 9,770 250 5,770 5,420 5,720 5,900 6,740 7,480 8,230 9,510 10,650 12,760 15,760
210 4,140 4,050 3,520 3,960 4,050 4,580 4,890 5,500 6,380 7,000 8,280 10,210 201~210 AM21 AM22 AM20 AM23 AM23 AM24 AM25 AM28 AM32 AM35
300 7,040 6,650 7,130 7,310 8,230 9,110 9,950 11,530 13,070 14,880 18,480 100 AM19 AM20 AM18 AM21 AM21 AM22 AM23 AM25 AM29 AM32
125 160 7,970 7,700 8,320 8,580 9,640 10,610 11,530 13,420 15,140 16,990 21,260
250 4,490 4,580 3,960 4,400 4,490 5,110 5,460 5,990 7,220 8,320 9,510 11,880 211~250 AM21 AM22 AM20 AM23 AM23 AM24 AM25 AM28 AM32 AM35
300 5,370 5,680 5,370 6,030 6,120 6,960 7,530 8,190 9,680 10,780 14,000 16,280 350 AM19 AM20 AM18 AM21 AM21 AM22 AM23 AM25 AM29 AM32
350 6,520 6,780 6,470 7,130 7,310 8,190 8,450 9,640 11,220 12,150 15,140 17,960
400 6,910 7,880 6,910 7,750 7,840 8,720 9,380 10,520 12,100 13,250 16,280 19,630 400 8,890 8,360 8,800 9,110 10,260 11,440 12,630 14,660 16,500 19,100 24,030 251~300 AM21 AM22 AM20 AM23 AM23 AM24 AM25 AM28 AM32 AM35
450 7,750 8,980 7,750 8,540 8,720 9,900 10,300 11,620 13,640 15,180 17,430 21,300 AM19 AM20 AM18 AM21 AM21 AM22 AM23 AM25 AM29 AM32
500 8,320 9,950 8,140 9,110 9,200 10,480 11,180 12,280 14,440 16,280 18,480 22,880 450 9,820 9,380 10,430 10,700 11,930 13,030 14,080 16,420 18,880 21,210 26,800
301~350 AM21 AM22 AM20 AM23 AM23 AM24 AM25 AM28 AM32 AM35
500 10,610 9,950 11,180 11,400 12,720 13,820 14,920 17,430 20,160 23,320 29,480 AM19 AM20 AM18 AM21 AM21 AM22 AM23 AM25 AM29 AM32
200 6,080 5,770 6,090 6,120 6,960 7,700 8,410 9,640 11,050 12,630 16,110 351~400 AM21 AM22 AM20 AM23 AM23 AM24 AM25 AM28 AM32 AM35
AM19 AM20 AM18 AM21 AM21 AM22 AM23 AM25 AM29 AM32
250 7,180 6,820 7,530 7,620 8,450 9,330 10,170 11,880 13,510 15,400 19,280 401~450 AM21 AM22 AM20 AM23 AM23 AM24 AM25 AM28 AM32 AM35
AM19 AM20 AM18 AM21 AM21 AM22 AM23 AM25 AM29 AM32
300 8,410 8,140 8,900 9,160 10,170 11,220 12,240 14,300 16,240 18,530 22,360
451~500 AM21 AM22 AM20 AM23 AM23 AM24 AM25 AM28 AM32 AM35
AM19 AM20 AM18 AM21 AM21 AM22 AM23 AM25 AM29 AM32
350 200 9,380 9,330 10,310 10,520 11,750 12,940 14,130 16,550 18,750 21,390 25,440
AM29 AM30 AM28 AM31 AM31 AM35 AM39 AM42 AM45 AM54 AM57 AM67
400 10,340 10,390 11,690 11,750 13,120 14,440 15,760 18,440 20,950 23,900 28,520 50~125 AM26 AM27 AM25 AM28 AM28 AM32 AM35 AM38 AM41 AM49 AM51 AM60
450 11,310 11,220 12,500 12,760 14,220 15,670 17,120 20,020 22,750 25,960 31,600 126~150 AM25 AM25 AM24 AM26 AM26 AM30 AM34 AM35 AM40 AM46 AM55 AM65
AM23 AM23 AM22 AM23 AM23 AM27 AM31 AM32 AM36 AM41 AM50 AM59
500 12,280 11,840 13,300 13,470 15,050 16,590 18,130 21,210 24,070 27,500 34,590 151~160 AM25 AM25 AM24 AM26 AM26 AM30 AM34 AM35 AM40 AM46 AM55 AM65
AM23 AM23 AM22 AM23 AM23 AM27 AM31 AM32 AM36 AM41 AM50 AM59
250 8,450 8,100 8,700 8,800 10,480 11,360 12,680 14,830 16,810 19,140 23,630
161~180 AM24 AM25 AM23 AM25 AM25 AM29 AM32 AM35 AM37 AM46 AM54 AM63
300 10,170 9,900 10,620 10,830 12,590 13,560 15,050 17,160 19,800 22,440 29,040 AM22 AM23 AM21 AM23 AM23 AM26 AM29 AM32 AM33 AM41 AM49 AM57
350 11,180 10,920 11,850 12,020 14,170 15,580 16,940 19,760 22,400 25,570 30,720 181~200 AM24 AM25 AM23 AM25 AM25 AM29 AM32 AM35 AM37 AM46 AM54 AM63
250 12,540 12,150 13,000 13,380 15,670 16,990 18,750 21,920 25,000 28,470 34,150 AM22 AM23 AM21 AM23 AM23 AM26 AM29 AM32 AM33 AM41 AM49 AM57
400 201~210 AM24 AM25 AM23 AM25 AM25 AM29 AM32 AM35 AM37 AM43 AM54 AM63
211~250 AM22 AM23 AM21 AM23 AM23 AM26 AM29 AM32 AM33 AM39 AM49 AM57
450 13,910 13,470 14,510 14,920 17,300 18,970 20,600 24,070 27,330 31,160 38,330 125 AM24 AM25 AM23 AM25 AM25 AM29 AM32 AM35 AM37 AM43 AM54 AM63
AM22 AM23 AM21 AM23 AM23 AM26 AM29 AM32 AM33 AM39 AM49 AM57
500 15,180 14,440 15,850 16,060 18,480 19,800 21,920 25,570 29,620 33,750 42,160
251~300 AM24 AM25 AM23 AM25 AM25 AM29 AM32 AM35 AM37 AM43 AM54 AM63
300 13,640 15,580 16,900 18,660 21,870 24,730 27,570 32,780 AM22 AM23 AM21 AM23 AM23 AM26 AM29 AM32 AM33 AM39 AM49 AM57
350 16,110 18,840 20,640 22,440 26,450 29,040 31,890 37,820 301~350 AM22 AM23 AM21 AM24 AM24 AM26 AM29 AM32 AM37 AM42 AM54 AM63
AM20 AM21 AM19 AM22 AM22 AM23 AM26 AM29 AM33 AM38 AM49 AM57
400 300 17,820 20,950 22,710 25,220 29,750 33,360 36,200 42,980 351~400 AM22 AM23 AM21 AM24 AM24 AM26 AM29 AM32 AM36 AM42 AM50 AM59
AM20 AM21 AM19 AM22 AM22 AM23 AM26 AM29 AM32 AM38 AM45 AM53
450 21,700 23,850 25,880 27,860 32,610 37,620 40,530 48,080
401~450 AM22 AM23 AM21 AM24 AM24 AM26 AM29 AM32 AM36 AM42 AM50 AM59
500 25,000 26,050 27,720 29,750 34,590 46,820 49,100 53,180 AM20 AM21 AM19 AM22 AM22 AM23 AM26 AM29 AM32 AM38 AM45 AM53
451~500 AM22 AM23 AM21 AM24 AM24 AM26 AM29 AM32 AM36 AM42 AM50 AM59
AM20 AM21 AM19 AM22 AM22 AM23 AM26 AM29 AM32 AM38 AM45 AM53
1163 1164
Express P.38 http://misumi.jp/press/ For inquiry, ordering and
service system Press 2007 other information, refer to P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES -SK- Heat treatment data P.1186
-STANDARDCSIZE SPECIFIEDCECONOMY TYPE-
SK (Standard type) Price calculation formula Upper : Size specified type Price calculation formula Upper : Size specified type
S-SK (Size specified type) (AMPrice coefficient) Lower : Economy type (AMPrice coefficient) Lower : Economy type
E-SK (Economy type)
AT 5 8 10 13 15 16 20 22 25 30 35 AT 5 8 10 13 15 16 20 22 25 30 35
A (1mm incr.)B (1mm incr.)B
Dimension tolerance
Precision standards P.1158 T Type 25~100 AM12 AM13 101~150 AM25 AM26 AM29 AM26 AM29 AM29 AM33 AM34 AM35 AM37 AM53
25 AM11 AM12 AM23 AM24 AM27 AM24 AM27 AM27 AM30 AM31 AM32 AM34 AM48
ACB T AM 9 AM10
101~250 AM 9 AM 9
99mm or less +0.4 151~180 AM25 AM25 AM25 AM24 AM25 AM25 AM29 AM30 AM32 AM37 AM53
0 AM23 AM23 AM23 AM22 AM23 AM23 AM27 AM27 AM29 AM34 AM48
B
SK Standard 100~250mm +0.5 +0.5 30~100 AM14 AM15 181~200 AM25 AM25 AM25 AM24 AM25 AM25 AM29 AM30 AM32 AM36 AM50
Size specified 0 +0.2 AM13 AM14 AM23 AM23 AM23 AM22 AM23 AM23 AM27 AM27 AM29 AM33 AM45
251mm or more +0.8 101~200 40 AM11 AM12 201~210 AM22 AM23 AM24 AM22 AM24 AM24 AM26 AM29 AM30 AM36 AM50
0 AM10 AM11 AM20 AM21 AM22 AM20 AM22 AM22 AM24 AM27 AM27 AM33 AM45
99mm or less +0.4 201~400 AM 9 AM10 211~250 AM22 AM23 AM24 AM22 AM24 AM24 AM26 AM29 AM30 AM36 AM50
0 AM 9 AM 9 251~300
AM20 AM21 AM22 AM20 AM22 AM22 AM24 AM27 AM27 AM33 AM45
Economy 100~250mm +0.5 +0.6 AM19 AM21 AM22 AM21 AM23 AM23 AM24 AM25 AM28 AM30 150 AM22 AM23 AM24 AM22 AM24 AM24 AM26 AM29 AM30 AM35 AM47
0 +0.3 AM18 AM19 AM20 AM19 AM21 AM21 AM22 AM23 AM26 AM27
30~ 60
+0.8 AM20 AM21 AM22 AM20 AM22 AM22 AM24 AM27 AM27 AM32 AM43
251mm or more 0
AM19 AM21 AM22 AM21 AM23 AM23 AM24 AM25 AM28 AM30 AM20 AM21 AM22 AM20 AM21 AM21 AM24 AM25 AM26 AM35 AM47
61~ 80 AM18 AM19 AM20 AM19 AM21 AM21 AM22 AM23 AM26 AM27 301~350 AM18 AM19 AM20 AM18 AM19 AM19 AM22 AM23 AM24 AM32 AM43
SKS93(For oil hardeningCRaw material) 81~100 AM15 AM17 AM18 AM17 AM18 AM18 AM20 AM21 AM22 AM24 351~400 AM20 AM21 AM22 AM20 AM21 AM21 AM24 AM25 AM26 AM33 AM44
AM14 AM16 AM17 AM16 AM17 AM17 AM18 AM19 AM20 AM22 AM18 AM19 AM20 AM18 AM19 AM19 AM22 AM23 AM24 AM30 AM40
Catalog No. ABT IVolume discount rate P.37 To be quoted on 101~200 60 AM13 AM15 AM18 AM17 AM18 AM18 AM20 AM21 AM22 AM24 401~450 AM20 AM21 AM22 AM20 AM21 AM21 AM24 AM25 AM26 AM33 AM44
price & lead time AM12 AM14 AM17 AM16 AM17 AM17 AM18 AM19 AM20 AM22 AM18 AM19 AM20 AM18 AM19 AM19 AM22 AM23 AM24 AM30 AM40
Order SK 300 100 10 Price Quantity 1~9 10~30 above Max. Q'ty.
S-SK 180 40 10 201~300 AM13 AM15 AM15 AM15 AM15 AM15 AM18 AM20 AM21 AM22 451~500 AM20 AM21 AM22 AM20 AM21 AM21 AM24 AM25 AM26 AM33 AM44
E-SK 120 40 10 Rate - 5% AM12 AM14 AM14 AM14 AM14 AM14 AM17 AM18 AM19 AM20 AM18 AM19 AM20 AM18 AM19 AM19 AM22 AM23 AM24 AM30 AM40
A(dimension A)MPrice coefficient=Unit price 301~400 AM13 AM15 AM15 AM15 AM15 AM15 AM18 AM20 AM21 AM22 101~160 AM24 AM25 AM28 AM25 AM28 AM28 AM32 AM33 AM34 AM36 AM52
AM12 AM14 AM14 AM14 AM14 AM14 AM17 AM18 AM19 AM20 AM22 AM23 AM26 AM23 AM26 AM26 AM29 AM30 AM31 AM33 AM47
(ex)S-SK-180-40-10
401~500 AM12 AM13 AM14 AM13 AM15 AM15 AM17 AM19 AM20 AM21 161~200 AM20 AM21 AM23 AM22 AM24 AM24 AM26 AM29 AM30 AM35 AM47
3Delivery Days 180 M 12 =\2,160 AM11 AM12 AM13 AM12 AM14 AM14 AM16 AM18 AM18 AM19 AM18 AM19 AM21 AM20 AM22 AM22 AM24 AM27 AM27 AM32 AM43
Alteration P.1174(B and T dimension changeable) 30~ 80 AM20 AM22 AM23 AM22 AM24 AM24 AM25 AM26 AM29 AM33 AM35 201~250 AM20 AM21 AM22 AM21 AM23 AM23 AM25 AM28 AM29 AM35 AM46
Alterations are available for size specified and economy type. AM18 AM20 AM21 AM20 AM22 AM22 AM23 AM24 AM27 AM30 AM32 AM18 AM19 AM20 AM19 AM21 AM21 AM23 AM26 AM27 AM32 AM42
Express A 800/1Pc. P.38 81~100 AM19 AM19 AM20 AM19 AM21 AM21 AM22 AM25 AM26 AM28 AM31 251~300 AM18 AM19 AM20 AM19 AM23 AM23 AM25 AM28 AM29 AM34 AM46
AM18 AM18 AM18 AM18 AM19 AM19 AM20 AM23 AM24 AM26 AM28 301~350
160 AM17 AM18 AM18 AM18 AM21 AM21 AM23 AM26 AM27 AM31 AM42
A flat charge of 2,160 yen for 3 pieces or more of the same size. AM14 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM28 AM18 AM19 AM20 AM19 AM20 AM20 AM23 AM24 AM25 AM34 AM46
101~125 AM13 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM26
AM17 AM18 AM18 AM18 AM18 AM18 AM21 AM22 AM23 AM31 AM42
U/Price(Standard type) U/Price(Standard type)
126~150 AM14 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM28 351~400 AM18 AM19 AM20 AM19 AM20 AM20 AM23 AM24 AM25 AM32 AM43
151~160 AM17 AM18 AM18 AM18 AM18 AM18 AM21 AM22 AM23 AM29 AM39
A B T 5 8 10 13 15 16 20 22 25 30 35 A B T 5 8 10 13 15 16 20 22 25 30 35 80 AM13 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM26
AM14 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM28 AM18 AM19 AM20 AM19 AM20 AM20 AM23 AM24 AM25 AM32 AM43
401~450 AM17 AM18 AM18 AM18 AM18 AM18 AM21 AM22 AM23 AM29 AM39
250 25 1,590 1,760 150 2,730 3,040 3,300 3,040 3,390 3,390 3,700 3,920 4,140 4,930 6,740 AM13 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM26
400 40 2,690 3,000 180 3,390 3,660 3,570 3,260 3,610 3,610 4,140 4,400 4,620 5,810 7,790 161~200 AM14 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM28 451~500 AM18 AM19 AM20 AM19 AM20 AM20 AM23 AM24 AM25 AM32 AM43
AM13 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM26 AM17 AM18 AM18 AM18 AM18 AM18 AM21 AM22 AM23 AM29 AM39
60 930 1,020 1,100 930 970 970 1,100 1,190 1,280 1,500 200 3,700 3,920 3,660 3,390 3,740 3,740 4,360 4,670 4,890 6,250 8,320 201~250 AM14 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM28 101~200 AM26 AM30 AM26 AM30 AM30 AM34 AM35 AM37 AM37 AM53
AM13 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM26 AM24 AM27 AM24 AM27 AM27 AM31 AM32 AM34 AM34 AM48
80 60 1,020 1,100 1,190 1,020 1,060 1,060 1,280 1,410 1,500 1,540 210 3,830 4,050 3,880 3,570 3,920 3,920 4,490 4,800 5,060 6,520 8,580
251~500 AM14 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM28 201~250 AM23 AM25 AM23 AM25 AM25 AM29 AM31 AM34 AM35 AM48
500 4,450 5,020 5,460 5,330 5,900 5,900 6,740 7,040 7,660 8,190 250 4,230 4,400 4,710 4,180 4,450 4,450 4,980 5,280 5,590 7,440 9,600 AM13 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM26 AM21 AM23 AM21 AM23 AM23 AM27 AM28 AM31 AM32 AM44
150
80 1,060 1,240 1,280 1,100 1,190 1,190 1,280 1,410 1,540 1,680 2,070 30~100 AM21 AM24 AM25 AM24 AM25 AM25 AM29 AM33 AM34 AM35 AM37 251~300 AM23 AM25 AM23 AM25 AM25 AM29 AM31 AM34 AM35 AM48
300 4,980 5,150 5,500 4,930 5,280 5,280 5,940 6,340 6,650 9,200 12,460 AM19 AM22 AM23 AM22 AM23 AM23 AM27 AM30 AM31 AM32 AM34 AM21 AM23 AM21 AM23 AM23 AM27 AM28 AM31 AM32 AM44
100 1,100 1,280 1,320 1,240 1,410 1,410 1,500 1,590 1,680 1,900 2,120 350 5,810 5,990 6,470 5,720 6,120 6,120 6,820 7,260 7,660 9,990 13,160 101~125 AM15 AM19 AM20 AM19 AM21 AM21 AM23 AM26 AM28 AM31 AM34 301~350 200 AM21 AM24 AM21 AM23 AM23 AM26 AM29 AM31 AM35 AM48
AM14 AM18 AM18 AM18 AM19 AM19 AM21 AM24 AM26 AM28 AM31 AM19 AM22 AM19 AM21 AM21 AM24 AM27 AM28 AM32 AM44
125 1,280 1,500 1,630 1,410 1,500 1,500 1,630 1,980 2,070 2,290 2,510 400 6,600 6,910 7,260 6,560 7,000 7,000 7,790 8,320 8,800 11,310 14,480 126~150 AM15 AM17 AM18 AM15 AM18 AM18 AM20 AM22 AM23 AM26 AM30 351~400 AM21 AM24 AM21 AM23 AM23 AM26 AM29 AM31 AM35 AM45
AM14 AM16 AM17 AM14 AM17 AM17 AM18 AM20 AM21 AM24 AM27 AM19 AM22 AM19 AM21 AM21 AM24 AM27 AM28 AM32 AM41
150 1,460 1,810 1,940 1,760 1,850 1,850 2,030 2,120 2,560 2,910 3,260 450 7,310 7,620 8,230 7,310 7,790 7,790 8,720 9,290 9,820 12,370 16,150
80 151~160 AM15 AM17 AM18 AM15 AM18 AM18 AM20 AM22 AM23 AM26 AM30 401~450 AM20 AM23 AM20 AM22 AM22 AM25 AM28 AM30 AM35 AM45
500 8,010 8,360 9,110 8,010 8,630 8,630 9,600 10,260 10,830 13,420 16,990 AM14 AM16 AM17 AM14 AM17 AM17 AM18 AM20 AM21 AM24 AM27 AM18 AM21 AM18 AM20 AM20 AM23 AM26 AM27 AM32 AM41
160 1,540 1,900 2,070 1,900 1,980 1,980 2,250 2,420 2,690 3,130 3,520
AM15 AM17 AM18 AM15 AM18 AM18 AM20 AM22 AM23 AM26 AM30 AM20 AM23 AM20 AM22 AM22 AM25 AM28 AM30 AM35 AM45
200 1,850 2,340 2,510 2,250 2,420 2,420 2,820 3,040 3,300 3,570 4,050 160 2,640 2,950 3,220 2,950 3,300 3,300 3,610 3,830 4,050 4,840 6,650 161~180 AM14 AM16 AM17 AM14 AM17 AM17 AM18 AM20 AM21 AM24 AM27 451~500 AM18 AM21 AM18 AM20 AM20 AM23 AM26 AM27 AM32 AM41
250 2,340 2,640 2,950 2,780 3,040 3,040 3,390 3,830 4,010 4,840 5,460 200 3,440 3,520 3,390 3,130 3,480 3,480 4,100 4,400 4,620 5,990 8,060 181~200 AM15 AM17 AM18 AM15 AM18 AM18 AM20 AM22 AM23 AM26 AM30 101~200 AM29 AM32 AM30 AM34 AM34 AM36 AM39 AM41 AM53 AM57
AM14 AM16 AM17 AM14 AM17 AM17 AM18 AM20 AM21 AM24 AM27 AM27 AM29 AM27 AM31 AM31 AM33 AM36 AM37 AM48 AM52
500 4,710 5,240 5,640 5,420 6,080 6,080 6,870 7,350 7,790 8,360 10,650 250 3,880 4,050 4,360 3,830 4,100 4,100 4,620 4,930 5,240 7,090 9,240
201~210 100 AM15 AM17 AM18 AM15 AM18 AM18 AM20 AM22 AM23 AM26 AM30 201~250 AM25 AM29 AM26 AM30 AM30 AM33 AM35 AM36 AM50 AM56
100 1,280 1,500 1,630 1,370 1,500 1,500 1,630 1,980 2,070 2,290 2,510 300 4,620 4,800 5,150 4,580 4,930 4,930 5,590 5,990 6,300 8,850 12,100 AM14 AM16 AM17 AM14 AM17 AM17 AM18 AM20 AM21 AM24 AM27 AM23 AM27 AM24 AM27 AM27 AM30 AM32 AM33 AM45 AM51
160
125 1,410 1,680 1,810 1,540 1,680 1,680 1,900 2,250 2,380 2,640 3,040 211~250 AM15 AM17 AM18 AM15 AM18 AM18 AM20 AM22 AM23 AM26 AM30 251~300 AM25 AM29 AM26 AM30 AM30 AM33 AM35 AM36 AM50 AM56
350 5,460 5,640 6,120 5,370 5,770 5,770 6,470 6,910 7,310 9,640 12,810 AM14 AM16 AM17 AM14 AM17 AM17 AM18 AM20 AM21 AM24 AM27 AM23 AM27 AM24 AM27 AM27 AM30 AM32 AM33 AM45 AM51
150 1,500 1,850 1,980 1,720 1,810 1,810 2,030 2,340 2,470 3,000 3,440 400 6,160 6,470 6,820 6,120 6,560 6,560 7,350 7,880 8,360 10,870 14,040 251~300 AM15 AM17 AM18 AM15 AM18 AM18 AM20 AM22 AM23 AM26 AM30 301~350 250 AM25 AM29 AM26 AM30 AM30 AM33 AM35 AM36 AM50 AM56
AM14 AM16 AM17 AM14 AM17 AM17 AM18 AM20 AM21 AM24 AM27 AM23 AM27 AM24 AM27 AM27 AM30 AM32 AM33 AM45 AM51
160 1,630 2,030 2,160 1,900 1,980 1,980 2,340 2,470 2,730 3,260 3,700 450 6,870 7,180 7,790 6,870 7,350 7,350 8,280 8,850 9,380 11,930 15,710 301~350 AM15 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM29 351~400 AM25 AM29 AM26 AM30 AM30 AM33 AM35 AM36 AM50 AM56
AM14 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM27 AM23 AM27 AM24 AM27 AM27 AM30 AM32 AM33 AM45 AM51
180 1,900 2,250 2,470 2,200 2,420 2,420 2,780 2,950 3,170 3,740 4,230 500 7,570 7,920 8,670 7,570 8,190 8,190 9,160 9,820 10,390 12,980 16,550
351~400 AM15 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM29 401~450 AM24 AM26 AM25 AM28 AM28 AM31 AM33 AM35 AM47 AM55
200 1,940 2,340 2,560 2,290 2,510 2,510 2,860 3,130 3,390 4,100 4,760 200 3,740 4,140 3,830 4,230 4,230 4,760 4,980 5,280 6,250 8,320 AM14 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM27 AM22 AM24 AM23 AM26 AM26 AM28 AM30 AM32 AM43 AM50
210 100 1,980 2,380 2,600 2,340 2,560 2,560 2,910 3,350 3,610 4,230 4,930 250 4,320 4,800 4,360 4,760 4,760 5,330 5,720 6,250 7,750 10,080 401~450 AM15 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM29 451~500 AM23 AM25 AM24 AM26 AM26 AM30 AM32 AM34 AM46 AM55
AM14 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM27 AM21 AM23 AM22 AM24 AM24 AM27 AM29 AM31 AM42 AM50
250 2,510 2,780 3,170 2,860 3,130 3,130 3,610 3,880 4,180 4,620 5,330 300 5,150 5,720 5,150 5,680 5,680 6,470 6,960 7,480 9,330 11,750 451~500 AM15 AM15 AM17 AM15 AM17 AM17 AM19 AM21 AM22 AM25 AM29 101~200 AM41 AM43 AM40 AM45 AM45 AM53 AM55 AM62 AM63 AM67
AM14 AM14 AM16 AM14 AM16 AM16 AM18 AM19 AM20 AM23 AM27 AM37 AM39 AM36 AM41 AM41 AM48 AM50 AM56 AM57 AM61
300 3,170 3,440 3,880 3,520 3,660 3,660 4,180 4,800 5,110 5,590 6,560 350 200 5,990 6,690 6,030 6,650 6,650 7,480 7,970 8,720 9,900 13,420
50~125 AM23 AM25 AM26 AM25 AM26 AM26 AM30 AM31 AM32 AM36 AM39 201~300 AM35 AM39 AM39 AM41 AM41 AM46 AM50 AM55 AM56 AM65
350 3,880 4,140 4,670 4,230 4,580 4,580 5,330 5,720 6,210 6,740 7,790 400 6,820 7,660 6,910 7,570 7,570 8,540 9,020 9,950 12,100 15,270 AM21 AM23 AM24 AM23 AM24 AM24 AM27 AM28 AM29 AM33 AM36 AM32 AM36 AM36 AM37 AM37 AM42 AM45 AM50 AM51 AM59
400 4,400 4,620 5,150 4,580 5,020 5,020 5,770 6,300 7,000 7,530 9,020 450 7,570 8,500 7,700 8,540 8,540 9,510 10,120 11,140 13,600 17,650 126~150 AM17 AM19 AM20 AM19 AM21 AM21 AM22 AM25 AM26 AM32 AM33 301~350 AM34 AM36 AM36 AM39 AM39 AM44 AM45 AM50 AM56 AM65
AM16 AM18 AM18 AM18 AM19 AM19 AM20 AM23 AM24 AM29 AM30 300 AM31 AM33 AM33 AM36 AM36 AM40 AM41 AM45 AM51 AM59
AM34 AM36 AM36 AM39 AM39 AM44 AM45 AM50 AM53 AM65
450 4,760 5,020 5,900 5,280 5,720 5,720 6,600 7,220 7,700 8,500 10,260 500 8,580 9,380 8,450 9,330 9,330 10,430 11,090 12,280 14,830 18,620 151~160 AM17 AM19 AM20 AM19 AM21 AM21 AM22 AM25 AM26 AM32 AM33 351~400 AM31 AM33 AM33 AM36 AM36 AM40 AM41 AM45 AM48 AM59
AM16 AM18 AM18 AM18 AM19 AM19 AM20 AM23 AM24 AM27 AM30
500 5,020 5,240 6,340 5,720 6,210 6,210 7,180 7,750 8,320 9,110 11,400 250 4,930 5,640 5,020 5,550 5,550 6,160 6,650 7,260 10,560 11,970 161~180 AM15 AM17 AM19 AM18 AM19 AM19 AM21 AM25 AM25 AM30 AM32 401~450 AM30 AM35 AM35 AM36 AM36 AM43 AM45 AM48 AM52 AM64
AM14 AM16 AM18 AM17 AM18 AM18 AM19 AM23 AM23 AM27 AM29 AM27 AM32 AM32 AM33 AM33 AM39 AM41 AM44 AM47 AM58
125 1,540 1,900 2,030 1,760 1,900 1,900 2,070 2,340 2,510 3,000 3,480 300 5,990 6,690 6,120 6,820 6,820 7,530 8,060 8,890 12,940 14,350
181~200 AM15 AM17 AM19 AM18 AM19 AM19 AM21 AM25 AM25 AM30 AM32 451~500 AM30 AM35 AM35 AM36 AM36 AM43 AM45 AM48 AM52 AM64
150 1,720 1,980 2,160 1,940 2,120 2,120 2,380 2,560 3,000 3,520 4,010 350 7,000 7,880 6,870 7,750 7,750 8,540 9,380 10,120 13,820 16,680 AM14 AM16 AM18 AM17 AM18 AM18 AM19 AM23 AM23 AM27 AM29 AM27 AM32 AM32 AM33 AM33 AM39 AM41 AM44 AM47 AM58
250 7,920 8,980 7,880 8,850 8,850 9,770 10,700 11,580 14,790 19,230
160 1,940 2,200 2,380 2,120 2,290 2,290 2,560 2,780 3,170 3,700 4,320 201~210 AM15 AM17 AM18 AM17 AM18 AM18 AM20 AM22 AM24 AM29 AM31
400 211~250
125 AM14 AM16 AM17 AM16 AM17 AM17 AM18 AM20 AM22 AM27 AM28
180 2,030 2,420 2,600 2,340 2,510 2,510 2,820 3,040 3,300 3,920 4,620 450 8,980 9,680 8,940 9,990 9,990 10,920 11,930 12,980 15,710 21,780 AM15 AM17 AM18 AM17 AM18 AM18 AM20 AM22 AM24 AM29 AM31
200 2,070 2,470 2,820 2,510 2,730 2,730 2,950 3,130 3,480 4,450 5,150 500 9,950 11,090 9,900 11,050 11,050 12,190 13,250 14,390 16,640 23,900 AM14 AM16 AM17 AM16 AM17 AM17 AM18 AM20 AM22 AM27 AM28
210 2,120 2,510 2,910 2,640 2,860 2,860 3,220 3,390 3,880 4,710 5,370 300 8,800 9,240 8,630 10,040 10,040 11,310 11,970 13,030 14,960 16,720 251~300 AM15 AM17 AM18 AM17 AM18 AM18 AM20 AM22 AM24 AM29 AM31
125 AM14 AM16 AM17 AM16 AM17 AM17 AM18 AM20 AM22 AM27 AM28
250 2,470 2,910 3,170 2,820 3,080 3,080 3,440 3,740 5,020 5,500 6,120 350 9,600 9,770 10,340 10,870 10,870 12,100 12,760 13,860 15,710 19,450 301~350 AM15 AM17 AM18 AM17 AM18 AM18 AM20 AM22 AM24 AM29 AM31
AM14 AM16 AM17 AM16 AM17 AM17 AM18 AM20 AM22 AM27 AM28
300 3,440 3,960 4,320 3,830 4,230 4,230 4,800 5,150 5,770 7,260 8,100 400 300 10,390 11,090 11,580 12,190 12,190 13,640 14,700 15,930 18,040 22,180 351~400 AM15 AM17 AM18 AM17 AM18 AM18 AM20 AM22 AM24 AM29 AM31
AM14 AM16 AM17 AM16 AM17 AM17 AM18 AM20 AM22 AM27 AM28
350 4,050 4,670 5,150 4,580 5,060 5,060 5,640 6,030 6,740 7,880 9,330 450 11,090 12,460 12,590 13,290 13,290 15,270 16,370 17,740 20,110 24,910 401~450 AM15 AM17 AM18 AM17 AM18 AM18 AM20 AM22 AM24 AM29 AM31
AM14 AM16 AM17 AM16 AM17 AM17 AM18 AM20 AM22 AM27 AM28
400 4,670 4,930 5,680 5,020 5,460 5,460 5,860 6,740 7,000 8,500 10,560 500 11,710 13,560 14,000 14,610 14,610 16,990 17,960 19,540 22,360 27,460
451~500 AM15 AM17 AM18 AM17 AM18 AM18 AM20 AM22 AM24 AM29 AM31
450 5,110 5,860 6,520 5,810 6,340 6,340 7,000 7,440 8,360 9,110 11,800 AM14 AM16 AM17 AM16 AM17 AM17 AM18 AM20 AM22 AM27 AM28
1165 1166
500 5,460 6,300 7,000 6,250 6,820 6,820 7,570 8,060 8,940 9,640 12,940 Express P.38 http://misumi.jp/press/ For inquiry, ordering and
service system Press 2007 other information, refer to P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES -HPM-
-STANDARDCSIZE SPECIFIEDCECONOMY TYPE-
HPM (Standard type) Price calculation formula Upper : Size specified type Price calculation formula Upper : Size specified type
S-HPM (Size specified type) (AMPrice coefficient) Lower : Economy type (AMPrice coefficient) Lower : Economy type
E-HPM (Economy type)
Dimension tolerance AT 8 10 13 15 16 20 22 25 30 35 40 50 AT 8 10 13 15 16 20 22 25 30 35 40 50
A (1mm incr.)B (1mm incr.)B
Type ACB T
Precision standards P.1158
T 30~ 60 AM28 AM25 AM28 AM30 AM30 AM32 AM34 101~150 AM39 AM37 AM36 AM42 AM42 AM46 AM50 AM53 AM62 AM79 AM92 AM117
AM26 AM23 AM26 AM27 AM27 AM29 AM31 AM36 AM34 AM33 AM38 AM38 AM42 AM45 AM48 AM56 AM72 AM83 AM106
99mm or less +0.4
0
Standard AM25 AM25 AM25 AM25 AM25 AM28 AM30 AM37 AM36 AM36 AM41 AM41 AM45 AM47 AM51 AM59 AM75 AM90 AM115
B Size specified 100~250mm +0.5 +0.3 61~ 80 AM23 AM23 AM23 AM23 AM23 AM26 AM27 151~180 AM34 AM33 AM33 AM37 AM37 AM41 AM43 AM46 AM54 AM68 AM81 AM104
HPM 0 +0.1
251mm or more +0.8 81~100 AM25 AM25 AM25 AM25 AM25 AM28 AM30 181~200 AM35 AM34 AM33 AM37 AM37 AM43 AM45 AM47 AM55 AM69 AM89 AM112
0 AM23 AM23 AM23 AM23 AM23 AM26 AM27 AM32 AM31 AM30 AM34 AM34 AM39 AM41 AM43 AM50 AM63 AM81 AM101
99mm or less +0.4 101~200 60 AM20 AM19 AM20 AM22 AM22 AM24 AM25 201~210 AM35 AM34 AM33 AM37 AM37 AM43 AM45 AM47 AM55 AM69 AM89 AM112
0 AM18 AM18 AM18 AM20 AM20 AM22 AM23 AM32 AM31 AM30 AM34 AM34 AM39 AM41 AM43 AM50 AM63 AM81 AM101
Economy 100~250mm +0.5 +0.4 AM20 AM19 AM20 AM22 AM22 AM24 AM25 AM35 AM34 AM33 AM37 AM37 AM43 AM45 AM47 AM55 AM69 AM89 AM112
0 +0.2 AM18 AM18 AM18 AM20 AM20 AM22 AM23
201~300 211~250
251mm or more +0.8 251~300 AM32 AM31 AM30 AM34 AM34 AM39 AM41 AM43 AM50 AM63 AM81 AM101
0 150 AM35 AM34 AM33 AM37 AM37 AM43 AM45 AM47 AM55 AM69 AM89 AM112
HPM2T 301~400 AM20 AM19 AM20 AM22 AM22 AM24 AM25 AM32 AM31 AM30 AM34 AM34 AM39 AM41 AM43 AM50 AM63 AM81 AM101
37~41HRC AM18 AM18 AM18 AM20 AM20 AM22 AM23
401~500 AM18 AM17 AM18 AM20 AM20 AM22 AM23 301~350 AM31 AM30 AM29 AM35 AM35 AM39 AM41 AM45 AM55 AM69 AM86 AM110
AM17 AM16 AM17 AM18 AM18 AM20 AM21 AM28 AM27 AM27 AM32 AM32 AM36 AM37 AM41 AM50 AM63 AM78 AM99
Catalog No. ABT IVolume discount rate P.37 To be quoted on 30~ 80 AM30 AM29 AM30 AM31 AM31 AM33 AM35 AM36 351~400 AM31 AM30 AM29 AM35 AM35 AM39 AM41 AM45 AM55 AM65 AM86 AM110
price & lead time AM27 AM27 AM27 AM28 AM28 AM30 AM32 AM33 AM28 AM27 AM27 AM32 AM32 AM36 AM37 AM41 AM50 AM59 AM78 AM99
Order HPM 125 125 20 Price above Max. Q'ty.
S-HPM 440 160 20 Quantity 1~9 10~30 81~100 AM25 AM24 AM25 AM25 AM25 AM29 AM30 AM33 401~450 AM31 AM30 AM29 AM35 AM35 AM39 AM41 AM45 AM55 AM65 AM86 AM110
E-HPM 320 160 20 AM23 AM22 AM23 AM23 AM23 AM27 AM27 AM30 AM28 AM27 AM27 AM32 AM32 AM36 AM37 AM41 AM50 AM59 AM78 AM99
Rate - 5%
A(dimension A)MPrice coefficient=Unit price 101~125 AM22 AM21 AM22 AM23 AM23 AM25 AM26 AM29 451~500 AM31 AM30 AM29 AM35 AM35 AM39 AM41 AM45 AM55 AM65 AM86 AM110
(ex)S-HPM-440-100-10 AM20 AM19 AM20 AM21 AM21 AM23 AM24 AM27 AM28 AM27 AM27 AM32 AM32 AM36 AM37 AM41 AM50 AM59 AM78 AM99
3Delivery 440 M 22 =\9,680 126~150 AM22 AM21 AM22 AM23 AM23 AM25 AM26 AM29 101~160 AM35 AM35 AM35 AM40 AM40 AM45 AM46 AM51 AM58 AM68 AM88 AM112
151~160 AM32 AM32 AM32 AM36 AM36 AM41 AM42 AM46 AM53 AM62 AM80 AM101
Days 80 AM20 AM19 AM20 AM21 AM21 AM23 AM24 AM27
AM22 AM21 AM22 AM23 AM23 AM25 AM26 AM29
161~200 AM33 AM32 AM31 AM36 AM36 AM41 AM43 AM46 AM55 AM68 AM86 AM109
P.1174(B and T dimension changeable) AM20 AM19 AM20 AM21 AM21 AM23 AM24 AM27 AM30 AM29 AM28 AM33 AM33 AM37 AM39 AM42 AM50 AM62 AM78 AM99
Express A 800/1Pc. P.38 Alterations Alterations are available for size specified and economy type.
161~200 AM22 AM21 AM22 AM23 AM23 AM25 AM26 AM29 201~250 AM33 AM32 AM31 AM36 AM36 AM41 AM43 AM46 AM55 AM65 AM86 AM109
A flat charge of 2,160 yen for 3 pieces or more of the same size. AM20 AM19 AM20 AM21 AM21 AM23 AM24 AM27 AM30 AM29 AM28 AM33 AM33 AM37 AM39 AM42 AM50 AM59 AM78 AM99
201~250 AM22 AM21 AM22 AM23 AM23 AM25 AM26 AM29 251~300 AM33 AM30 AM29 AM35 AM35 AM39 AM41 AM45 AM55 AM65 AM86 AM109
AM20 AM19 AM20 AM21 AM21 AM23 AM24 AM27 301~350
U/Price(Standard type) U/Price(Standard type) 160 AM30 AM27 AM27 AM32 AM32 AM36 AM37 AM41 AM50 AM59 AM78 AM99
A B T 8 10 13 15 16 20 22 25 30 35 40 50 AM22 AM21 AM22 AM23 AM23 AM25 AM26 AM29 AM29 AM28 AM26 AM33 AM33 AM36 AM39 AM43 AM55 AM65 AM81 AM107
60 1,280 1,280 1,150 1,280 1,280 1,410 1,500 251~500 AM20 AM19 AM20 AM21 AM21 AM23 AM24 AM27
80 60 1,680 1,500 1,410 1,500 1,500 1,680 1,760 A B T 8 10 13 15 16 20 22 25 30 35 40 50 AM27 AM26 AM24 AM30 AM30 AM33 AM36 AM39 AM50 AM59 AM73 AM97
500 7,480 7,480 7,220 8,100 8,100 8,980 10,040
80 1,680 1,680 1,590 1,760 1,760 1,940 2,030 2,120 150 4,580 4,580 4,450 4,890 4,890 5,370 5,900 6,430 7,570 9,770 12,540 15,540 30~100 AM32 AM30 AM32 AM33 AM33 AM34 AM35 AM37 AM45 351~400 AM29 AM28 AM26 AM33 AM33 AM36 AM39 AM43 AM53 AM63 AM81 AM107
100 1,850 1,850 1,850 2,030 2,030 2,290 2,380 2,560 AM29 AM27 AM29 AM30 AM30 AM31 AM32 AM34 AM41 AM27 AM26 AM24 AM30 AM30 AM33 AM36 AM39 AM48 AM57 AM73 AM97
125 2,290 2,290 2,200 2,380 2,380 2,640 2,820 3,000
150 2,470 2,780 2,690 3,040 3,040 3,440 3,570 3,830 180 5,460 5,280 5,020 5,720 5,720 6,250 6,960 7,570 8,540 11,050 14,960 17,560 101~125 AM26 AM25 AM26 AM28 AM28 AM29 AM30 AM32 AM41 401~450 AM29 AM28 AM26 AM33 AM33 AM36 AM39 AM43 AM53 AM63 AM81 AM107
AM24 AM23 AM24 AM26 AM26 AM27 AM27 AM29 AM37 AM27 AM26 AM24 AM30 AM30 AM33 AM36 AM39 AM48 AM57 AM73 AM97
80 200 5,900 5,720 5,460 6,430 6,430 6,870 7,840 8,360 9,240 11,710 15,540 18,920
160 2,560 2,950 2,780 3,080 3,080 3,660 3,790 4,050 AM24 AM23 AM24 AM25 AM25 AM28 AM29 AM31 AM41 AM29 AM28 AM26 AM33 AM33 AM36 AM39 AM43 AM53 AM63 AM81 AM107
200 3,080 3,300 3,300 3,880 3,880 4,320 4,580 4,760 210 6,120 6,080 5,810 6,780 6,780 7,400 8,140 8,800 9,860 12,280 15,950 19,810 126~150 AM22 AM21 AM22 AM23 AM23 AM26 AM27 AM28 AM37 451~500 AM27 AM26 AM24 AM30 AM30 AM33 AM36 AM39 AM48 AM57 AM73 AM97
250 4,540 4,140 3,960 4,760 4,760 5,200 5,550 5,810
500 7,310 7,840 7,750 9,240 9,240 9,420 10,120 11,000 250 6,960 6,960 6,740 7,840 7,840 8,940 9,380 10,260 12,240 14,440 18,800 22,800 151~160 AM24 AM23 AM24 AM25 AM25 AM28 AM29 AM31 AM41 101~200 AM41 AM41 AM45 AM45 AM52 AM55 AM59 AM75 AM86 AM97 AM124
100 2,200 2,200 2,290 2,380 2,380 2,560 2,640 2,820 3,440 150 AM22 AM21 AM22 AM23 AM23 AM26 AM27 AM28 AM37 AM37 AM37 AM41 AM41 AM47 AM50 AM54 AM68 AM78 AM88 AM112
125 2,560 2,510 2,640 2,730 2,730 3,080 3,170 3,390 4,400
150 3,040 3,040 2,910 3,300 3,300 3,700 3,830 4,100 5,110 300 7,750 7,750 7,480 9,070 9,070 10,120 10,650 11,710 14,610 17,080 21,360 26,880 AM24 AM23 AM24 AM25 AM25 AM28 AM29 AM31 AM41 AM36 AM35 AM40 AM40 AM45 AM48 AM53 AM75 AM86 AM97 AM124
160 3,260 3,220 3,170 3,520 3,520 3,920 4,050 4,360 5,640 AM22 AM21 AM22 AM23 AM23 AM26 AM27 AM28 AM37 AM33 AM32 AM36 AM36 AM41 AM44 AM48 AM68 AM78 AM88 AM112
180 3,660 3,610 3,520 3,960 3,960 4,400 4,580 4,890 6,160 350 8,980 8,980 8,670 10,520 10,520 11,750 12,370 13,600 16,460 19,720 24,580 30,800 161~180 201~250
200 4,050 4,050 3,880 4,400 4,400 4,930 5,110 5,460 6,870
210 100 4,100 4,050 4,050 4,400 4,400 4,980 5,150 5,550 7,130 400 10,300 10,300 9,950 12,060 12,060 13,470 14,170 15,580 18,400 22,440 27,520 35,200 181~200 AM24 AM23 AM24 AM25 AM25 AM28 AM29 AM31 AM41 251~300 AM36 AM35 AM40 AM40 AM45 AM48 AM53 AM70 AM83 AM95 AM119
250 4,840 4,840 4,670 5,280 5,280 5,940 6,160 6,600 8,360 AM22 AM21 AM22 AM23 AM23 AM26 AM27 AM28 AM37 AM33 AM32 AM36 AM36 AM41 AM44 AM48 AM63 AM75 AM86 AM108
300 5,810 5,810 5,640 6,340 6,340 7,130 7,400 7,920 9,860 450 11,530 11,530 11,140 13,510 13,510 15,100 15,890 17,470 20,240 25,080 30,960 39,600
350 6,780 6,600 6,520 7,400 7,400 8,320 8,630 9,240 11,360 201~210 100 AM23 AM22 AM23 AM24 AM24 AM26 AM28 AM30 AM40 301~350 200 AM36 AM35 AM40 AM40 AM45 AM48 AM53 AM68 AM83 AM95 AM119
400 7,750 7,750 7,310 8,360 8,360 9,510 9,860 10,560 12,760 500 12,760 12,760 12,320 14,960 14,960 16,720 17,600 19,360 22,000 27,720 34,400 48,000 AM21 AM20 AM21 AM22 AM22 AM24 AM26 AM27 AM36 AM33 AM32 AM36 AM36 AM41 AM44 AM48 AM62 AM75 AM86 AM108
450 8,720 8,360 8,190 9,510 9,510 10,700 11,090 11,880 14,350
500 9,680 9,240 9,070 10,560 10,560 11,880 12,320 13,200 15,760 160 4,490 4,490 4,360 4,760 4,760 5,280 5,810 6,340 7,480 9,680 12,460 15,100 211~250 AM23 AM22 AM23 AM24 AM24 AM26 AM28 AM30 AM40 351~400 AM33 AM32 AM35 AM35 AM42 AM44 AM47 AM68 AM83 AM95 AM119
125 2,860 2,860 2,950 3,170 3,170 3,520 3,610 4,050 4,710 5,720 7,530 9,240 AM21 AM20 AM21 AM22 AM22 AM24 AM26 AM27 AM36 AM30 AM29 AM32 AM32 AM38 AM40 AM43 AM62 AM75 AM86 AM108
150 3,440 3,440 3,570 3,830 3,830 4,230 4,360 4,890 5,640 6,160 8,100 9,950
160 3,660 3,660 3,700 4,050 4,050 4,490 4,620 5,200 6,120 6,870 8,540 10,520 200 5,640 5,460 5,200 6,160 6,160 6,600 7,570 8,100 8,980 11,440 15,230 18,480 251~300 AM23 AM22 AM23 AM24 AM24 AM26 AM28 AM30 AM40 401~450 AM32 AM31 AM35 AM35 AM40 AM42 AM45 AM64 AM76 AM89 AM114
180 4,140 4,100 4,140 4,580 4,580 5,020 5,200 5,860 6,690 8,100 9,460 11,660 AM21 AM20 AM21 AM22 AM22 AM24 AM26 AM27 AM36 AM29 AM28 AM32 AM32 AM36 AM38 AM41 AM58 AM69 AM81 AM103
200 4,230 4,230 4,400 4,580 4,580 5,280 5,460 5,990 7,180 8,720 10,390 12,810 250 6,600 6,600 6,380 7,480 7,480 8,580 9,020 9,900 11,880 14,080 18,220 22,440
210 4,450 4,400 4,620 4,800 4,800 5,550 5,720 6,250 7,440 8,980 10,830 13,380 AM23 AM22 AM23 AM24 AM24 AM26 AM28 AM30 AM40 AM32 AM31 AM35 AM35 AM40 AM42 AM45 AM64 AM76 AM89 AM114
300 7,400 7,400 7,130 8,720 8,720 9,770 10,300 11,360 14,260 16,720 21,210 26,320 301~350 AM21 AM20 AM21 AM22 AM22 AM24 AM26 AM27 AM36 451~500 AM29 AM28 AM32 AM32 AM36 AM38 AM41 AM58 AM69 AM81 AM103
125 160
250 5,060 5,060 5,280 5,500 5,500 6,340 6,600 7,260 8,800 10,830 12,500 15,580 351~400 AM23 AM22 AM23 AM24 AM24 AM26 AM28 AM30 AM40 101~200 AM45 AM45 AM48 AM48 AM55 AM57 AM64 AM88 AM105 AM117 AM138
300 6,080 6,080 6,340 6,600 6,600 7,660 7,920 8,720 11,090 13,120 18,400 21,390 350 8,630 8,630 8,320 10,170 10,170 11,400 12,020 13,250 16,110 19,360 24,200 30,230 AM21 AM20 AM21 AM22 AM22 AM24 AM26 AM27 AM36 AM41 AM41 AM44 AM44 AM50 AM52 AM58 AM80 AM95 AM106 AM125
350 7,090 7,090 7,400 7,700 7,700 8,940 9,240 10,170 12,850 15,050 19,890 23,590
400 8,100 8,100 8,450 8,800 8,800 10,210 10,560 11,620 14,610 17,120 21,390 25,790 400 9,860 9,860 9,510 11,620 11,620 13,030 13,730 15,140 17,960 22,000 27,200 33,710 AM23 AM22 AM23 AM24 AM24 AM26 AM28 AM30 AM40 AM41 AM40 AM44 AM44 AM50 AM52 AM57 AM84 AM103 AM117 AM138
450 9,110 9,110 9,510 9,900 9,900 11,490 11,880 13,070 16,460 19,190 22,880 27,990 AM21 AM20 AM21 AM22 AM22 AM24 AM26 AM27 AM36 AM37 AM36 AM40 AM40 AM45 AM47 AM52 AM76 AM93 AM106 AM125
500 10,120 10,120 10,560 11,000 11,000 12,760 13,200 14,520 18,040 21,120 24,290 30,100 450 11,090 11,090 10,700 13,070 13,070 14,660 15,450 17,030 19,800 24,640 30,190 37,580 401~450 201~250
500 12,320 12,320 11,880 14,520 14,520 16,280 17,160 18,920 21,560 27,280 33,180 47,440 451~500 AM23 AM22 AM23 AM24 AM24 AM26 AM28 AM30 AM40 251~300 AM41 AM40 AM44 AM44 AM50 AM52 AM57 AM84 AM103 AM117 AM138
AM21 AM20 AM21 AM22 AM22 AM24 AM26 AM27 AM36 AM37 AM36 AM40 AM40 AM45 AM47 AM52 AM76 AM93 AM106 AM125
200 6,340 6,340 7,040 7,040 8,100 8,630 9,330 12,760 14,960 17,080 21,830
50~125 AM35 AM33 AM35 AM35 AM35 AM41 AM43 AM45 AM50 AM59 AM75 AM85 301~350 250 AM41 AM40 AM44 AM44 AM50 AM52 AM57 AM84 AM103 AM117 AM138
250 7,920 7,920 8,800 8,800 10,120 10,780 11,660 15,400 17,600 20,820 26,100 AM32 AM30 AM32 AM32 AM32 AM37 AM39 AM41 AM45 AM54 AM68 AM77 AM37 AM36 AM40 AM40 AM45 AM47 AM52 AM76 AM93 AM106 AM125
300 9,510 9,510 10,560 10,560 12,150 12,940 14,000 18,040 21,560 25,040 30,280 126~150 AM26 AM25 AM26 AM29 AM29 AM32 AM33 AM36 AM44 AM53 AM69 AM85 351~400 AM37 AM36 AM41 AM41 AM46 AM52 AM55 AM84 AM103 AM114 AM133
AM24 AM23 AM24 AM27 AM27 AM29 AM30 AM33 AM40 AM48 AM63 AM77 AM34 AM33 AM37 AM37 AM42 AM47 AM50 AM76 AM93 AM103 AM120
350 200 9,860 9,860 11,090 11,090 12,940 13,560 14,790 20,160 24,200 28,870 34,410 151~160 AM26 AM25 AM26 AM29 AM29 AM32 AM33 AM36 AM44 AM52 AM69 AM81 401~450 AM37 AM36 AM41 AM41 AM46 AM50 AM54 AM80 AM98 AM114 AM133
AM24 AM23 AM24 AM27 AM27 AM29 AM30 AM33 AM40 AM47 AM63 AM73 AM34 AM33 AM37 AM37 AM42 AM45 AM49 AM72 AM89 AM103 AM120
400 10,920 10,920 12,320 12,320 14,080 14,790 16,200 22,270 26,840 32,260 38,550
AM26 AM25 AM26 AM29 AM29 AM32 AM33 AM36 AM44 AM52 AM69 AM81 AM36 AM35 AM40 AM40 AM45 AM47 AM53 AM80 AM92 AM109 AM129
450 12,280 12,280 13,860 13,860 15,840 16,640 18,220 24,200 29,480 35,030 42,680 161~180 AM24 AM23 AM24 AM27 AM27 AM29 AM30 AM33 AM40 AM47 AM63 AM73 451~500 AM33 AM32 AM36 AM36 AM41 AM43 AM48 AM72 AM83 AM99 AM117
500 13,640 13,640 15,400 15,400 17,600 18,480 20,240 26,400 31,680 37,050 46,730 181~200 AM26 AM25 AM26 AM29 AM29 AM32 AM33 AM36 AM44 AM52 AM69 AM81 101~200 AM65 AM75 AM80 AM86 AM97 AM114 AM124 AM145
AM24 AM23 AM24 AM27 AM27 AM29 AM30 AM33 AM40 AM47 AM63 AM73 AM59 AM68 AM72 AM78 AM88 AM103 AM112 AM131
250 8,800 8,800 9,680 9,680 11,000 11,440 12,680 17,600 21,120 24,030 29,700
AM25 AM24 AM25 AM25 AM25 AM30 AM31 AM34 AM43 AM51 AM69 AM81 AM62 AM69 AM74 AM78 AM97 AM114 AM124 AM145
201~210 201~300 AM56 AM63 AM67 AM71 AM88 AM103 AM112 AM131
300 10,560 10,560 11,620 11,620 13,200 13,730 15,050 22,000 27,280 30,890 36,520 211~250 AM23 AM22 AM23 AM23 AM23 AM27 AM28 AM31 AM39 AM46 AM63 AM73
125 AM25 AM24 AM25 AM25 AM25 AM30 AM31 AM34 AM43 AM51 AM69 AM81
AM58 AM66 AM70 AM77 AM97 AM113 AM120 AM142
350 11,400 11,400 12,630 12,630 14,480 15,580 16,940 25,080 30,360 35,120 38,640 AM23 AM22 AM23 AM23 AM23 AM27 AM28 AM31 AM39 AM46 AM63 AM73 301~350 AM53 AM60 AM63 AM70 AM88 AM102 AM108 AM128
250 13,030 13,030 14,440 14,440 16,550 17,600 19,010 28,160 33,440 39,080 42,950 300 AM58 AM66 AM70 AM77 AM97 AM113 AM120 AM142
251~300 AM24 AM23 AM24 AM25 AM25 AM29 AM30 AM33 AM43 AM51 AM69 AM81 AM53 AM60 AM63 AM70 AM88 AM102 AM108 AM128
400 AM22 AM21 AM22 AM23 AM23 AM27 AM27 AM30 AM39 AM46 AM63 AM73 351~400
450 14,260 14,260 15,840 15,840 18,220 19,010 20,990 31,240 36,520 42,770 48,230
500 15,840 15,840 17,600 17,600 20,240 21,120 23,320 32,560 39,600 46,290 53,020 301~350 AM24 AM23 AM24 AM25 AM25 AM29 AM30 AM33 AM43 AM51 AM69 AM81 401~450 AM57 AM65 AM69 AM75 AM96 AM108 AM118 AM138
AM22 AM21 AM22 AM23 AM23 AM27 AM27 AM30 AM39 AM46 AM63 AM73 AM52 AM59 AM63 AM68 AM87 AM98 AM107 AM125
300 16,370 18,040 19,540 20,860 24,730 29,920 31,200 38,660 351~400 AM24 AM23 AM24 AM25 AM25 AM29 AM30 AM33 AM42 AM50 AM65 AM76 451~500 AM57 AM65 AM69 AM75 AM96 AM108 AM118 AM138
AM22 AM21 AM22 AM23 AM23 AM27 AM27 AM30 AM38 AM45 AM59 AM69 AM52 AM59 AM63 AM68 AM87 AM98 AM107 AM125
350 18,180 20,640 21,870 24,030 29,920 34,320 36,400 40,820
AM24 AM23 AM24 AM25 AM25 AM29 AM30 AM33 AM42 AM50 AM65 AM76
400 300 20,770 23,590 25,000 27,460 33,880 38,720 41,220 44,120 401~450 AM22 AM21 AM22 AM23 AM23 AM27 AM27 AM30 AM38 AM45 AM59 AM69
450 22,970 26,140 27,720 29,700 37,840 43,120 47,400 50,360 451~500 AM24 AM23 AM24 AM25 AM25 AM29 AM30 AM33 AM42 AM50 AM65 AM76
AM22 AM21 AM22 AM23 AM23 AM27 AM27 AM30 AM38 AM45 AM59 AM69
500 25,520 27,020 30,800 33,000 40,480 47,520 50,200 56,590
1167 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1168
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES -SC-
-STANDARDCSIZE SPECIFIEDCECONOMY TYPE-
SC (Standard type) Price calculation formula Upper : Size specified type Price calculation formula Upper : Size specified type
S-SC (Size specified type) (AMPrice coefficient) Lower : Economy type (AMPrice coefficient) Lower : Economy type
E-SC (Economy type)
AT 8 10 13 15 16 20 22 25 30 35 40 50 AT 8 10 13 15 16 20 22 25 30 35 40 50
A (1mm incr.)B (1mm incr.)B
Dimension tolerance
Precision standards P.1158 T Type 30~ 60 AM18 AM19 AM15 AM17 AM17 AM19 101~150 AM18 AM18 AM17 AM18 AM18 AM19 AM20 AM21 AM24 AM28 AM34 AM41
AM17 AM18 AM14 AM16 AM16 AM18 AM17 AM17 AM16 AM17 AM17 AM18 AM18 AM19 AM22 AM26 AM31 AM37
ACB T
99mm or less +0.4 61~ 80 AM18 AM19 AM15 AM17 AM17 AM19 151~180 AM18 AM18 AM17 AM18 AM18 AM19 AM20 AM21 AM24 AM28 AM34 AM41
0 AM17 AM18 AM14 AM16 AM16 AM18 AM17 AM17 AM16 AM17 AM17 AM18 AM18 AM19 AM22 AM26 AM31 AM37
B
SC Standard 100~250mm +0.5 +0.3 81~100 AM15 AM17 AM15 AM17 AM17 AM18 181~200 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM30 AM36
Size specified 0 +0.1 AM14 AM16 AM14 AM16 AM16 AM17 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM27 AM33
251mm or more +0.8 60 AM12 AM13 AM12 AM12 AM12 AM13 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM30 AM36
0 AM11 AM12 AM11 AM11 AM11 AM12 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM27 AM33
101~200 201~210
99mm or less +0.4
0
AM11 AM12 AM11 AM11 AM11 AM12 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM30 AM36
Economy 100~250mm +0.5 +0.4 201~300 AM10 AM11 AM10 AM10 AM10 AM11 211~250 150 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM27 AM33
0 +0.2
251mm or more +0.8 301~400 AM11 AM12 AM11 AM11 AM11 AM12 251~300 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM30 AM36
0 AM10 AM11 AM10 AM10 AM10 AM11 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM27 AM33
S50C(Raw material) 401~500 AM11 AM12 AM11 AM11 AM11 AM12 301~350 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM30 AM36
AM10 AM11 AM10 AM10 AM10 AM11 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM27 AM33
Catalog No. AB T IVolume discount rate P.37 To be quoted on 30~ 80 AM18 AM19 AM15 AM17 AM17 AM19 AM19 AM22 AM24 AM26 351~400 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM30 AM36
price & lead time AM17 AM18 AM14 AM16 AM16 AM18 AM18 AM20 AM22 AM24 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM27 AM33
Order SC 100 100 8 Price above Max. Q'ty.
S-SC 380 200 30 Quantity 1~9 10~30 81~100 AM18 AM19 AM15 AM17 AM17 AM19 AM19 AM22 AM24 AM26 401~450 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM30 AM36
E-SC 210 150 22 AM17 AM18 AM14 AM16 AM16 AM18 AM18 AM20 AM22 AM24 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM27 AM33
Rate - 5%
A(dimension A)MPrice coefficient=Unit price 101~125 AM13 AM13 AM12 AM15 AM15 AM17 AM18 AM19 AM21 AM24 451~500 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM30 AM36
(ex)S-SC-300-200-30 AM12 AM12 AM11 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM27 AM33
3Delivery Days 300 M 25 =\7,500 126~150 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM21 101~160 AM18 AM17 AM15 AM18 AM18 AM19 AM20 AM21 AM23 AM26 AM33 AM41
151~160 80 AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM17 AM16 AM14 AM17 AM17 AM18 AM18 AM19 AM21 AM24 AM30 AM37
P.1174(B and T dimension changeable) AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM21 161~200 AM15 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM21 AM25 AM30 AM35
Alterations are available for size specified and economy type. AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM14 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM19 AM23 AM27 AM32
Express A 800/1Pc. P.38 Alteration
161~200 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM21 201~250 AM15 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM21 AM25 AM30 AM35
A flat charge of 2,160 yen for 3 pieces or more of the same size. AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM14 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM19 AM23 AM27 AM32
201~250 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 251~300 AM15 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM21 AM25 AM28 AM31
AM10 AM11 AM10 AM10 AM10 AM11 AM12 AM13 AM16 AM18 160 AM14 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM19 AM23 AM26 AM28
U/Price(Standard type) U/Price(Standard type)
A B T 8 10 13 15 16 20 22 25 30 35 40 50 A B T 8 10 13 15 16 20 22 25 30 35 40 50 251~500 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 301~350 AM15 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM21 AM25 AM28 AM31
60 930 970 840 840 840 970 150 1,900 1,940 1,720 1,810 1,810 1,980 2,070 2,200 2,470 3,040 3,780 4,890 AM10 AM11 AM10 AM10 AM10 AM11 AM12 AM13 AM16 AM18 AM14 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM19 AM23 AM26 AM28
80 60 1,020 1,020 880 880 880 1,060 180 2,160 2,200 1,980 2,120 2,120 2,380 2,560 2,730 3,170 3,740 4,150 4,990
500 3,960 4,100 3,610 3,790 3,790 4,320 200 2,290 2,380 2,160 2,290 2,290 2,600 2,820 3,040 3,520 4,140 4,520 5,290 30~100 AM19 AM19 AM17 AM18 AM18 AM19 AM20 AM23 AM25 AM29 AM32 AM37 351~400 AM15 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM21 AM25 AM28 AM31
80 1,020 1,100 930 930 930 1,100 1,150 1,280 1,500 1,850 210 2,420 2,510 2,290 2,420 2,420 2,690 2,910 3,130 3,660 4,270 4,920 5,780 AM18 AM18 AM16 AM17 AM17 AM18 AM18 AM21 AM23 AM27 AM29 AM34 AM14 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM19 AM23 AM26 AM28
100 1,060 1,100 1,020 1,150 1,150 1,320 1,410 1,460 1,680 2,030 250 2,910 3,040 2,730 2,950 2,950 3,000 3,170 3,350 3,960 4,620 5,760 6,520
125 1,150 1,190 1,100 1,190 1,190 1,370 1,460 1,500 1,760 2,200 101~125 AM15 AM15 AM14 AM15 AM15 AM17 AM18 AM19 AM22 AM26 AM30 AM35 401~450 AM15 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM21 AM25 AM28 AM31
150 1,280 1,370 1,240 1,320 1,320 1,410 1,500 1,590 1,850 2,290 150 AM14 AM14 AM13 AM14 AM14 AM16 AM17 AM18 AM20 AM24 AM27 AM32 AM14 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM19 AM23 AM26 AM28
300 3,480 3,610 3,220 3,440 3,440 3,520 3,660 3,960 4,670 5,330 6,270 7,380
80 350 4,050 4,180 3,700 3,920 3,920 4,010 4,180 4,490 5,330 6,030 6,790 8,260 126~150 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM26 AM30 451~500 AM15 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM21 AM25 AM28 AM31
160 1,320 1,410 1,280 1,410 1,410 1,460 1,540 1,630 1,940 2,380 400 4,710 4,840 4,270 4,490 4,490 4,580 4,800 5,150 6,120 6,820 7,410 8,810 AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM24 AM27 AM14 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM19 AM23 AM26 AM28
200 1,590 1,680 1,460 1,590 1,590 1,720 1,940 2,120 2,380 2,820 450 5,240 5,420 4,760 4,980 4,980 5,110 5,330 5,770 6,820 7,570 8,230 9,750
250 2,030 2,160 1,940 2,030 2,030 2,290 2,420 2,560 2,820 3,260 500 5,460 5,810 5,110 5,420 5,420 5,590 5,860 6,300 7,530 8,320 9,080 10,730 151~160 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM26 AM30 101~200 AM23 AM22 AM21 AM23 AM23 AM24 AM25 AM25 AM28 AM33 AM34 AM37
500 4,010 4,180 3,700 3,880 3,880 4,360 4,620 4,980 5,460 6,250 160 1,810 1,850 1,630 1,720 1,720 1,900 1,980 2,120 2,380 2,950 3,610 4,760 AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM24 AM27 AM21 AM20 AM19 AM21 AM21 AM22 AM23 AM23 AM26 AM30 AM31 AM34
100 1,150 1,190 1,100 1,190 1,190 1,320 1,370 1,500 1,760 1,940 2,040 2,390 200 2,030 2,120 1,900 2,030 2,030 2,340 2,560 2,780 3,260 3,880 4,230 5,020
125 1,280 1,320 1,150 1,240 1,240 1,370 1,410 1,540 1,850 2,290 2,420 2,840 250 2,560 2,690 2,380 2,600 2,600 2,640 2,820 3,000 3,610 4,270 5,020 5,990 161~180 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM24 AM27 201~250 AM19 AM18 AM17 AM19 AM19 AM20 AM21 AM22 AM25 AM29 AM31 AM35
150 1,370 1,410 1,240 1,320 1,320 1,410 1,500 1,590 1,900 2,340 2,830 3,320 300 3,130 3,260 2,860 3,080 3,080 3,170 3,300 3,610 4,320 4,980 5,720 7,040 AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM22 AM25 AM18 AM17 AM16 AM18 AM18 AM18 AM19 AM20 AM23 AM27 AM28 AM32
160 1,500 1,540 1,370 1,460 1,460 1,540 1,630 1,720 2,030 2,470 2,970 3,470
180 1,590 1,680 1,460 1,540 1,540 1,630 1,720 1,900 2,200 2,640 3,300 3,860 160 181~200 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM24 AM27 251~300 AM19 AM18 AM17 AM19 AM19 AM20 AM21 AM22 AM25 AM29 AM31 AM35
200 1,680 1,760 1,590 1,680 1,680 1,850 1,980 2,070 2,380 2,820 3,620 4,240 350 3,700 3,830 3,350 3,570 3,570 3,660 3,830 4,140 4,980 5,680 6,470 7,880 AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM22 AM25 AM18 AM17 AM16 AM18 AM18 AM18 AM19 AM20 AM23 AM27 AM28 AM32
210 100 1,760 1,850 1,630 1,760 1,760 1,940 2,070 2,380 2,730 3,300 3,760 4,390 400 4,270 4,400 3,830 4,050 4,050 4,140 4,360 4,710 5,680 6,380 7,180 8,580
250 2,160 2,290 2,030 2,160 2,160 2,420 2,510 2,640 3,000 3,570 4,380 5,130 450 4,800 4,980 4,320 4,540 4,540 4,670 4,890 5,330 6,380 7,130 7,970 9,460 201~210 100 AM12 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM24 AM27 301~350 200 AM19 AM18 AM17 AM19 AM19 AM20 AM21 AM22 AM25 AM29 AM31 AM33
300 2,510 2,640 2,290 2,560 2,560 2,690 3,000 3,080 3,480 4,050 4,780 5,920 500 5,020 5,370 4,670 4,980 4,980 5,150 5,420 5,860 7,090 7,880 8,760 10,340 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM22 AM25 AM18 AM17 AM16 AM18 AM18 AM18 AM19 AM20 AM23 AM27 AM28 AM30
350 2,950 3,130 2,690 2,950 2,950 3,300 3,440 3,740 4,180 4,840 5,590 6,820 200 2,640 2,780 2,510 2,690 2,690 2,910 3,040 3,260 3,700 4,050 4,400 5,200
400 3,390 3,610 3,080 3,350 3,350 3,700 3,920 4,140 4,580 5,240 5,940 7,100 250 3,170 3,350 3,000 3,170 3,170 3,440 3,610 3,920 4,360 4,840 5,370 6,300 211~250 AM12 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM20 AM23 AM26 351~400 AM17 AM17 AM15 AM17 AM17 AM18 AM19 AM20 AM23 AM28 AM29 AM33
450 3,830 4,100 3,520 3,740 3,740 4,180 4,400 4,760 5,240 5,940 6,510 7,950 300 3,610 3,830 3,440 3,700 3,700 4,010 4,230 4,540 5,280 5,680 6,250 7,400 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM18 AM21 AM24 AM16 AM16 AM14 AM16 AM16 AM17 AM18 AM18 AM21 AM26 AM27 AM30
500 4,230 4,450 3,880 4,100 4,100 4,620 4,800 5,240 5,770 6,520 7,420 8,810 350 200 4,140 4,400 3,920 4,230 4,230 4,580 4,800 5,200 5,810 6,520 7,180 8,450
125 1,370 1,410 1,280 1,370 1,370 1,410 1,500 1,590 1,980 2,470 3,040 4,010 400 4,670 4,980 4,400 4,980 4,980 5,420 5,720 6,160 6,870 7,620 8,360 10,170 251~300 AM12 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM20 AM23 AM26 401~450 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM28 AM29 AM33
150 1,460 1,680 1,320 1,410 1,410 1,590 1,680 1,760 2,160 2,640 3,220 4,180 450 5,200 5,590 4,890 5,680 5,680 6,030 6,520 6,740 7,790 8,360 9,600 11,180 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM18 AM21 AM24 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM26 AM27 AM30
160 1,590 1,810 1,460 1,540 1,540 1,680 1,760 1,940 2,340 2,820 3,390 4,360 500 5,680 6,120 5,330 5,770 5,770 6,300 6,870 7,350 8,410 9,240 10,700 12,150
180 1,630 1,850 1,500 1,590 1,590 1,720 1,810 1,980 2,420 2,910 3,480 4,450 250 4,230 4,540 4,010 4,580 4,580 4,840 5,280 5,590 5,640 5,990 6,600 7,700 301~350 AM12 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM20 AM23 AM26 451~500 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM28 AM29 AM33
200 1,760 1,900 1,680 1,810 1,810 1,900 2,030 2,250 2,690 3,220 3,830 4,890 300 4,930 5,060 4,710 4,930 4,930 5,420 5,720 6,210 6,470 6,960 7,660 9,020 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM18 AM21 AM24 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM26 AM27 AM30
210 1,850 1,940 1,720 1,900 1,900 2,030 2,200 2,380 2,820 3,350 3,960 5,020 350 5,500 5,720 5,240 5,500 5,500 6,120 6,470 7,000 7,400 7,970 8,800 10,700
351~400 AM12 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM20 AM23 AM26 101~200 AM25 AM25 AM24 AM25 AM25 AM29 AM30 AM32 AM34 AM35 AM36 AM41
125 250 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM18 AM21 AM24 AM23 AM23 AM22 AM23 AM23 AM27 AM27 AM29 AM31 AM32 AM33 AM37
250 2,290 2,380 2,120 2,200 2,200 2,380 2,470 2,640 3,130 3,700 4,360 5,500 400 6,080 6,380 5,770 6,340 6,340 7,090 7,530 8,100 8,320 9,240 10,520 12,280
300 2,640 2,730 2,380 2,640 2,640 2,780 3,040 3,170 3,660 4,230 4,890 6,030 450 6,650 7,040 6,300 7,040 7,040 8,140 8,580 9,240 9,730 10,390 11,530 13,600 401~450 AM12 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM20 AM23 AM26 201~250 AM21 AM21 AM19 AM21 AM21 AM23 AM25 AM25 AM28 AM31 AM33 AM37
350 3,130 3,220 2,860 3,130 3,130 3,350 3,520 3,830 4,360 4,980 5,680 6,910 500 7,090 7,530 6,780 7,480 7,480 8,410 8,890 9,600 10,300 11,140 12,720 14,300 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM18 AM21 AM24 AM19 AM19 AM18 AM19 AM19 AM21 AM23 AM23 AM26 AM28 AM30 AM34
400 3,610 3,700 3,350 3,520 3,520 3,790 4,050 4,230 4,760 5,370 6,080 7,310 300 4,890 5,200 4,710 5,420 5,420 6,380 6,740 7,260 7,840 8,230 13,360 15,470
450 4,100 4,180 3,830 4,010 4,010 4,230 4,540 4,800 5,370 6,030 6,780 8,100 350 5,640 5,940 5,420 6,210 6,210 7,180 7,570 8,230 9,290 10,040 15,340 17,750 451~500 AM12 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM18 AM20 AM23 AM26 251~300 AM21 AM21 AM19 AM21 AM21 AM23 AM25 AM25 AM28 AM31 AM33 AM37
500 4,580 4,670 4,180 4,450 4,450 4,670 5,020 5,460 6,080 6,780 7,570 8,980 400 300 6,380 6,690 6,120 7,130 7,130 8,140 8,630 9,330 10,520 11,180 17,320 20,050 AM11 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM17 AM18 AM21 AM24 AM19 AM19 AM18 AM19 AM19 AM21 AM23 AM23 AM26 AM28 AM30 AM34
450 7,130 7,440 6,820 7,840 7,840 8,980 9,510 10,300 11,800 12,410 19,280 22,290
500 7,700 8,100 7,480 8,010 8,010 9,240 9,950 10,830 12,590 13,640 21,280 24,580 50~125 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM28 AM31 AM36 301~350 250 AM20 AM20 AM18 AM20 AM20 AM23 AM24 AM25 AM28 AM31 AM33 AM35
AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM26 AM28 AM33 AM18 AM18 AM17 AM18 AM18 AM21 AM22 AM23 AM26 AM28 AM30 AM32
126~150 AM14 AM14 AM13 AM13 AM13 AM14 AM14 AM15 AM20 AM24 AM28 AM36 351~400 AM19 AM19 AM18 AM19 AM19 AM21 AM22 AM24 AM25 AM30 AM31 AM35
AM13 AM13 AM12 AM12 AM12 AM13 AM13 AM14 AM18 AM22 AM26 AM33 AM18 AM18 AM17 AM18 AM18 AM19 AM20 AM22 AM23 AM27 AM28 AM32
151~160 AM14 AM14 AM13 AM13 AM13 AM14 AM14 AM15 AM20 AM24 AM28 AM32 401~450 AM19 AM19 AM17 AM19 AM19 AM21 AM22 AM24 AM25 AM30 AM31 AM35
AM13 AM13 AM12 AM12 AM12 AM13 AM13 AM14 AM18 AM22 AM26 AM29 AM18 AM18 AM16 AM18 AM18 AM19 AM20 AM22 AM23 AM27 AM28 AM32
161~180 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28 451~500 AM19 AM19 AM17 AM19 AM19 AM21 AM22 AM24 AM25 AM30 AM31 AM35
AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26 AM18 AM18 AM16 AM18 AM18 AM19 AM20 AM22 AM23 AM27 AM28 AM32
181~200 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28 101~200 AM32 AM32 AM30 AM33 AM33 AM36 AM39 AM42 AM45 AM48 AM60 AM67
AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26 AM29 AM29 AM27 AM30 AM30 AM33 AM36 AM38 AM41 AM44 AM54 AM61
201~210 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28 201~300 AM25 AM25 AM24 AM26 AM26 AM31 AM33 AM35 AM40 AM43 AM57 AM65
125 AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26 AM23 AM23 AM22 AM24 AM24 AM28 AM30 AM32 AM36 AM39 AM52 AM59
211~250 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28 301~350 AM25 AM25 AM23 AM25 AM25 AM30 AM32 AM35 AM39 AM42 AM57 AM63
AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26 300 AM23 AM23 AM21 AM23 AM23 AM27 AM29 AM32 AM36 AM38 AM52 AM57
251~300 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28 351~400 AM25 AM25 AM23 AM25 AM25 AM30 AM32 AM35 AM39 AM42 AM57 AM63
AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26 AM23 AM23 AM21 AM23 AM23 AM27 AM29 AM32 AM36 AM38 AM52 AM57
301~350 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28 401~450 AM23 AM23 AM21 AM24 AM24 AM26 AM29 AM32 AM35 AM39 AM55 AM61
AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26 AM21 AM21 AM19 AM22 AM22 AM24 AM27 AM29 AM32 AM36 AM50 AM55
351~400 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28 451~500 AM23 AM23 AM21 AM24 AM24 AM26 AM29 AM32 AM35 AM39 AM55 AM61
AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26 AM21 AM21 AM19 AM22 AM22 AM24 AM27 AM29 AM32 AM36 AM50 AM55
401~450 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28
AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26
451~500 AM13 AM13 AM12 AM12 AM12 AM13 AM14 AM15 AM19 AM22 AM25 AM28
AM12 AM12 AM11 AM11 AM11 AM12 AM13 AM14 AM18 AM20 AM23 AM26
1169 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1170
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES -SS-
-STANDARDCSIZE SPECIFIEDCECONOMY TYPE-
SS (Standard type) Price calculation formula Upper : Size specified type Price calculation formula Upper : Size specified type
S-SS (Size specified type) (AMPrice coefficient) Lower : Economy type (AMPrice coefficient) Lower : Economy type
E-SS (Economy type)
AT 8 10 13 15 16 20 22 25 30 35 40 50 AT 8 10 13 15 16 20 22 25 30 35 40 50
A (1mm incr.)B (1mm incr.)B
Dimension tolerance
Precision standards P.1158 T Type 30~ 60 AM17 AM18 AM15 AM15 AM15 AM18 AM20 AM22 101~150 AM17 AM18 AM17 AM18 AM18 AM19 AM20 AM21 AM24 AM26 AM26 AM36
AM16 AM17 AM14 AM14 AM14 AM17 AM18 AM20 AM16 AM17 AM16 AM17 AM17 AM18 AM18 AM19 AM22 AM24 AM24 AM33
ACB T
99mm or less +0.4 61~ 80 AM17 AM18 AM15 AM15 AM15 AM18 AM20 AM22 151~180 AM17 AM18 AM17 AM18 AM18 AM19 AM20 AM21 AM24 AM26 AM26 AM36
0 AM16 AM17 AM14 AM14 AM14 AM17 AM18 AM20 AM16 AM17 AM16 AM17 AM17 AM18 AM18 AM19 AM22 AM24 AM24 AM33
B Standard
SS Size specified 100~250mm +0.5 +0.3 81~100 AM14 AM15 AM14 AM15 AM15 AM17 AM18 AM20 181~200 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM24 AM24 AM32
0 +0.1 AM13 AM14 AM13 AM14 AM14 AM16 AM17 AM18 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM22 AM29
251mm or more +0.8 60 AM11 AM11 AM11 AM12 AM12 AM13 AM14 AM14 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM24 AM24 AM32
0 AM10 AM10 AM10 AM11 AM11 AM12 AM13 AM13 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM22 AM29
101~200 201~210
99mm or less +0.4
0
AM11 AM11 AM11 AM11 AM11 AM12 AM14 AM14 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM24 AM24 AM32
Economy 100~250mm +0.5 +0.4 201~300 AM10 AM10 AM10 AM10 AM10 AM11 AM13 AM13 211~250 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM22 AM29
0 +0.2
150
251mm or more +0.8 AM11 AM11 AM11 AM11 AM11 AM12 AM14 AM14 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM24 AM24 AM32
0 301~400 AM10 AM10 AM10 AM10 AM10 AM11 AM13 AM13 251~300 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM22 AM29
SS400(Raw material) 401~500 AM11 AM11 AM11 AM11 AM11 AM12 AM14 AM14 301~350 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM24 AM24 AM32
AM10 AM10 AM10 AM10 AM10 AM11 AM13 AM13 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM22 AM29
Catalog No. AB T IVolume discount rate P.37 To be quoted on 30~ 80 AM18 AM15 AM14 AM15 AM15 AM17 AM18 AM19 AM21 AM25 AM25 351~400 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM24 AM24 AM32
price & lead time AM17 AM14 AM13 AM14 AM14 AM16 AM17 AM18 AM19 AM23 AM23 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM22 AM29
Order SS 250 125 22 Price above Max. Q'ty.
S-SS 480 300 35 Quantity 1~9 10~30 81~100 AM15 AM15 AM14 AM15 AM15 AM17 AM18 AM19 AM21 AM25 AM25 401~450 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM24 AM24 AM32
E-SS 150 80 15 AM14 AM14 AM13 AM14 AM14 AM16 AM17 AM18 AM19 AM23 AM23 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM22 AM29
Rate - 5%
A(dimension A)MPrice coefficient=Unit price 101~125 AM12 AM13 AM12 AM13 AM13 AM14 AM15 AM15 AM19 AM23 AM23 451~500 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM24 AM24 AM32
(ex)S-SS-480-300-35 AM11 AM12 AM11 AM12 AM12 AM13 AM14 AM14 AM18 AM21 AM21 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM22 AM22 AM29
3Delivery Days 480 M 33 =\15,840 126~150 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 101~160 AM15 AM17 AM15 AM17 AM17 AM18 AM19 AM20 AM23 AM25 AM25 AM35
151~160 80 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM14 AM16 AM14 AM16 AM16 AM17 AM18 AM18 AM21 AM23 AM23 AM32
P.1174(B and T dimension changeable) AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 161~200 AM14 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM20 AM23 AM23 AM35
Alterations are available for size specified and economy type. AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM13 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM18 AM21 AM21 AM32
Express A 800/1Pc. P.38 Alteration
161~200 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 201~250 AM14 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM20 AM23 AM23 AM32
A flat charge of 2,160 yen for 3 pieces or more of the same size. AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM13 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM18 AM21 AM21 AM29
201~250 AM10 AM10 AM11 AM11 AM11 AM13 AM13 AM14 AM15 AM18 AM18 251~300 AM14 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM20 AM23 AM23 AM32
AM9 AM9 AM10 AM10 AM10 AM12 AM12 AM13 AM14 AM17 AM17 AM13 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM18 AM21 AM21 AM29
U/Price(Standard type) U/Price(Standard type) 160
A B T 8 10 13 15 16 20 22 25 30 35 40 50 A B T 8 10 13 15 16 20 22 25 30 35 40 50 AM10 AM10 AM11 AM11 AM11 AM12 AM13 AM14 AM15 AM18 AM18 AM14 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM20 AM23 AM23 AM30
60 880 930 800 800 800 930 1,050 1,150 150 1,760 1,850 1,720 1,810 1,810 1,940 2,070 2,200 2,470 2,910 4,050 4,910 251~500 AM9 AM9 AM10 AM10 AM10 AM11 AM12 AM13 AM14 AM17 AM17 301~350 AM13 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM18 AM21 AM21 AM27
80 60 930 1,020 840 840 840 1,020 1,180 1,240 180 2,030 2,120 1,980 2,070 2,070 2,340 2,510 2,690 3,000 3,350 4,520 5,290
500 3,660 3,700 3,520 3,700 3,700 4,230 4,270 4,320 200 2,200 2,290 2,160 2,290 2,290 2,560 2,730 2,950 3,260 3,960 4,810 5,820 30~100 AM18 AM15 AM14 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM25 AM32 351~400 AM14 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM20 AM23 AM23 AM30
80 970 1,020 880 880 880 1,060 1,150 1,280 1,410 1,760 210 2,340 2,420 2,290 2,380 2,380 2,600 2,820 3,040 3,350 4,140 5,010 6,000 AM17 AM14 AM13 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM23 AM29 AM13 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM18 AM21 AM21 AM27
100 1,020 1,060 970 1,060 1,060 1,150 1,280 1,370 1,590 1,940 250 2,730 2,820 2,640 2,860 2,860 2,910 3,080 3,300 3,570 4,400 5,890 8,160
125 1,100 1,150 1,100 1,150 1,150 1,240 1,320 1,410 1,680 2,070 101~125 AM14 AM14 AM13 AM14 AM14 AM15 AM15 AM17 AM19 AM25 AM25 AM32 401~450 AM14 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM20 AM23 AM23 AM30
150 1,280 1,370 1,240 1,320 1,320 1,370 1,410 1,590 1,760 2,200 150 AM13 AM13 AM12 AM13 AM13 AM14 AM14 AM16 AM18 AM23 AM23 AM29 AM13 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM18 AM21 AM21 AM27
300 3,170 3,260 3,080 3,350 3,350 3,440 3,520 3,790 4,140 5,200 7,060 8,380
80 350 3,700 3,790 3,520 3,790 3,790 3,960 4,100 4,400 4,760 5,770 8,020 9,510 126~150 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM20 AM20 AM29 451~500 AM14 AM14 AM13 AM15 AM15 AM15 AM17 AM18 AM20 AM23 AM23 AM30
160 1,320 1,370 1,280 1,370 1,370 1,460 1,540 1,630 2,030 2,290 400 4,230 4,320 4,050 4,320 4,320 4,490 4,710 5,060 5,460 6,690 9,380 11,070 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM27 AM13 AM13 AM12 AM14 AM14 AM14 AM16 AM17 AM18 AM21 AM21 AM27
200 1,590 1,680 1,410 1,590 1,590 1,680 1,720 1,810 2,380 2,640 450 4,760 4,840 4,580 4,840 4,840 5,020 5,240 5,640 6,080 7,440 10,170 12,090
250 1,940 2,030 1,850 1,980 1,980 2,200 2,250 2,380 2,640 3,080 500 4,980 5,240 4,980 5,280 5,280 5,550 5,720 6,160 6,650 8,060 11,420 13,320 151~160 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM20 AM20 AM29 101~200 AM21 AM21 AM20 AM21 AM21 AM22 AM23 AM25 AM28 AM32 AM32 AM38
500 3,610 3,700 3,610 3,790 3,790 4,320 4,580 4,840 5,060 6,250 160 1,680 1,760 1,630 1,720 1,720 1,850 1,980 2,120 2,380 2,820 3,950 4,830 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM27 AM19 AM19 AM18 AM19 AM19 AM20 AM21 AM23 AM26 AM29 AM29 AM35
100 1,150 1,190 1,100 1,190 1,190 1,280 1,370 1,460 1,590 1,760 1,880 2,290 200 1,940 2,030 1,900 2,030 2,030 2,290 2,470 2,690 3,000 3,700 4,760 5,790
125 1,280 1,320 1,150 1,240 1,240 1,320 1,410 1,500 1,680 2,120 2,220 2,750 250 2,380 2,470 2,290 2,510 2,510 2,560 2,730 2,950 3,220 4,050 5,790 7,000 161~180 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM20 AM20 AM29 201~250 AM18 AM18 AM17 AM18 AM18 AM19 AM20 AM21 AM24 AM28 AM28 AM36
150 1,320 1,370 1,240 1,320 1,320 1,410 1,500 1,590 1,760 2,200 2,590 3,120 300 2,820 2,910 2,730 3,000 3,000 3,080 3,170 3,440 3,790 4,840 6,800 8,180 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM27 AM17 AM17 AM16 AM17 AM17 AM18 AM18 AM19 AM22 AM26 AM26 AM33
160 1,460 1,500 1,320 1,410 1,410 1,460 1,540 1,680 1,940 2,380 2,720 3,280
180 1,500 1,630 1,460 1,500 1,500 1,590 1,630 1,760 2,120 2,560 3,030 3,620 160 181~200 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM20 AM20 AM29 251~300 AM18 AM18 AM17 AM18 AM18 AM19 AM20 AM21 AM24 AM28 AM28 AM36
200 1,590 1,720 1,500 1,630 1,630 1,760 1,810 2,070 2,290 2,730 3,320 3,960 350 3,350 3,440 3,170 3,440 3,440 3,610 3,740 4,050 4,400 5,420 7,830 9,380 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM27 AM17 AM17 AM16 AM17 AM17 AM18 AM18 AM19 AM22 AM26 AM26 AM33
210 100 1,680 1,760 1,540 1,680 1,680 1,810 1,980 2,200 2,640 3,170 3,450 4,110 400 3,790 3,880 3,610 3,880 3,880 4,050 4,270 4,620 5,020 6,250 8,860 10,590
250 1,980 2,030 1,980 2,120 2,120 2,200 2,380 2,470 2,780 3,440 4,000 4,790 450 4,320 4,400 4,140 4,400 4,400 4,580 4,800 5,200 5,640 7,000 9,860 11,780 201~210 100 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM20 AM20 AM29 301~350 200 AM18 AM18 AM17 AM18 AM18 AM19 AM20 AM21 AM24 AM28 AM28 AM34
300 2,250 2,380 2,290 2,380 2,380 2,560 2,860 2,910 2,950 3,700 4,720 5,630 500 4,540 4,800 4,540 4,840 4,840 5,110 5,280 5,720 6,210 7,620 10,880 12,990 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM27 AM17 AM17 AM16 AM17 AM17 AM18 AM18 AM19 AM22 AM26 AM26 AM31
350 2,640 2,780 2,560 2,820 2,820 3,080 3,260 3,350 3,520 4,670 5,450 6,460 200 2,510 2,640 2,340 2,470 2,470 2,600 2,730 2,910 3,260 3,880 5,990 7,950
400 3,040 3,170 3,000 3,260 3,260 3,520 3,700 3,960 4,400 5,110 6,150 7,290 250 3,080 3,130 2,860 3,080 3,080 3,260 3,520 3,700 4,140 4,670 7,250 8,370 211~250 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 AM27 351~400 AM15 AM17 AM15 AM17 AM17 AM18 AM19 AM20 AM23 AM26 AM26 AM33
450 3,440 3,520 3,440 3,700 3,700 4,100 4,320 4,580 4,980 5,810 6,870 8,130 300 3,480 3,610 3,170 3,610 3,610 3,880 4,100 4,320 4,840 5,640 8,490 9,780 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM25 AM14 AM16 AM14 AM16 AM16 AM17 AM18 AM18 AM21 AM24 AM24 AM30
500 3,700 3,790 3,790 4,050 4,050 4,490 4,670 5,020 5,370 6,520 7,580 8,950 350 200 4,010 4,180 3,610 3,960 3,960 4,270 4,400 4,580 5,110 6,380 9,720 11,220
125 1,320 1,410 1,240 1,320 1,320 1,370 1,410 1,540 1,980 2,380 2,660 3,200 400 4,540 4,760 4,050 4,760 4,760 4,930 5,150 5,330 5,810 7,310 10,990 12,640 251~300 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 AM27 401~450 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM25 AM33
150 1,370 1,500 1,320 1,410 1,410 1,590 1,680 1,760 2,160 2,560 3,080 3,790 450 5,110 5,150 4,490 5,150 5,150 5,550 5,720 5,990 6,520 8,280 12,220 14,080 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM25 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM24 AM30
160 1,500 1,720 1,410 1,500 1,500 1,630 1,720 1,900 2,340 2,730 3,240 3,990 500 5,280 5,460 4,890 5,550 5,550 6,120 6,300 6,470 7,350 8,890 13,470 15,500
180 1,590 1,810 1,500 1,590 1,590 1,680 1,760 1,940 2,380 2,820 3,590 4,380 250 3,350 3,390 3,260 3,520 3,520 3,700 3,960 4,050 4,270 5,240 8,720 10,080 301~350 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 AM27 451~500 AM15 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM22 AM25 AM25 AM33
200 1,720 1,850 1,590 1,720 1,720 1,850 2,030 2,200 2,640 3,170 3,910 4,790 300 3,660 3,920 3,570 3,960 3,960 4,320 4,710 4,930 5,370 5,810 9,720 11,800 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM25 AM14 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM20 AM23 AM23 AM30
210 1,810 1,900 1,630 1,810 1,810 1,940 2,120 2,290 2,820 3,260 4,090 4,990 350 4,270 4,710 4,270 4,760 4,760 5,020 5,460 5,720 6,250 6,910 11,750 13,510
351~400 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 AM27 101~200 AM21 AM22 AM21 AM22 AM22 AM23 AM25 AM28 AM30 AM33 AM33 AM43
125 250 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM25 AM19 AM20 AM19 AM20 AM20 AM21 AM23 AM26 AM27 AM30 AM30 AM39
250 2,030 2,200 2,070 2,160 2,160 2,290 2,420 2,510 2,950 3,520 4,780 5,780 400 4,890 5,500 4,980 5,550 5,550 5,810 6,080 6,250 6,870 7,480 13,250 15,240
300 2,510 2,600 2,340 2,470 2,470 2,600 2,950 3,000 3,130 4,050 5,590 6,780 450 5,500 6,300 5,680 6,340 6,340 6,600 6,780 6,960 7,570 8,360 14,740 16,850 401~450 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 AM27 201~250 AM19 AM19 AM18 AM20 AM20 AM21 AM23 AM25 AM26 AM30 AM30 AM40
350 2,910 3,000 2,780 2,860 2,860 3,220 3,390 3,440 3,660 4,760 6,420 7,790 500 5,990 6,520 6,250 6,520 6,520 7,040 7,400 7,700 8,280 9,510 16,240 18,660 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM25 AM18 AM18 AM17 AM18 AM18 AM19 AM21 AM23 AM24 AM27 AM27 AM36
400 3,170 3,260 3,260 3,480 3,480 3,610 4,010 4,180 4,580 5,200 7,290 8,790 300 4,710 5,200 4,670 5,370 5,370 6,080 6,520 7,040 7,350 7,570 11,990 13,800
450 3,520 3,700 3,660 3,880 3,880 4,140 4,400 4,670 5,060 5,900 8,110 9,760 350 5,240 5,680 5,280 5,990 5,990 6,160 6,650 7,400 8,280 8,890 13,750 15,820 451~500 AM12 AM12 AM12 AM12 AM12 AM13 AM14 AM15 AM17 AM19 AM19 AM27 251~300 AM19 AM19 AM18 AM20 AM20 AM21 AM23 AM25 AM26 AM30 AM30 AM40
500 3,880 4,010 3,960 4,320 4,320 4,580 4,760 5,200 5,720 6,690 8,950 10,760 400 300 5,770 6,160 5,900 6,470 6,470 6,910 7,660 8,320 9,420 9,950 15,510 17,840 AM11 AM11 AM11 AM11 AM11 AM12 AM13 AM14 AM16 AM18 AM18 AM25 AM18 AM18 AM17 AM18 AM18 AM19 AM21 AM23 AM24 AM27 AM27 AM36
450 6,300 6,820 6,520 7,090 7,090 7,790 8,500 9,420 10,560 12,150 17,250 19,820
500 6,780 7,040 6,960 7,480 7,480 8,580 9,420 10,210 11,880 13,200 19,030 21,830 50~125 AM18 AM15 AM15 AM15 AM15 AM17 AM18 AM19 AM21 AM25 AM25 AM34 301~350 250 AM19 AM19 AM18 AM20 AM20 AM21 AM23 AM25 AM26 AM30 AM30 AM40
AM17 AM14 AM14 AM14 AM14 AM16 AM17 AM18 AM19 AM23 AM23 AM31 AM18 AM18 AM17 AM18 AM18 AM19 AM21 AM23 AM24 AM27 AM27 AM36
126~150 AM15 AM13 AM12 AM13 AM13 AM14 AM15 AM17 AM19 AM22 AM22 AM32 351~400 AM18 AM18 AM17 AM19 AM19 AM20 AM21 AM24 AM25 AM29 AM29 AM39
AM14 AM12 AM11 AM12 AM12 AM13 AM14 AM16 AM18 AM20 AM20 AM29 AM17 AM17 AM16 AM18 AM18 AM18 AM19 AM22 AM23 AM27 AM27 AM36
151~160 AM13 AM13 AM12 AM13 AM13 AM14 AM15 AM17 AM19 AM22 AM22 AM32 401~450 AM18 AM18 AM17 AM19 AM19 AM20 AM21 AM24 AM25 AM29 AM29 AM39
AM12 AM12 AM11 AM12 AM12 AM13 AM14 AM16 AM18 AM20 AM20 AM29 AM17 AM17 AM16 AM18 AM18 AM18 AM19 AM22 AM23 AM27 AM27 AM36
161~180 AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28 451~500 AM18 AM18 AM17 AM19 AM19 AM20 AM21 AM24 AM25 AM29 AM29 AM39
AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26 AM17 AM17 AM16 AM18 AM18 AM18 AM19 AM22 AM23 AM27 AM27 AM36
181~200 AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28 101~200 AM28 AM29 AM28 AM29 AM29 AM31 AM34 AM35 AM39 AM44 AM44 AM55
AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26 AM26 AM27 AM26 AM27 AM27 AM28 AM31 AM32 AM36 AM40 AM40 AM50
201~210 AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28 201~300 AM24 AM25 AM24 AM25 AM25 AM28 AM30 AM32 AM35 AM37 AM37 AM52
AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26 AM22 AM23 AM22 AM23 AM23 AM26 AM27 AM29 AM32 AM34 AM34 AM47
125
AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28 AM21 AM22 AM21 AM22 AM22 AM24 AM25 AM29 AM32 AM35 AM35 AM49
211~250 AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26 301~350 AM19 AM20 AM19 AM20 AM20 AM22 AM23 AM27 AM29 AM32 AM32 AM45
AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28 300 AM21 AM22 AM21 AM22 AM22 AM24 AM25 AM29 AM32 AM35 AM35 AM49
AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26 AM19 AM20 AM19 AM20 AM20 AM22 AM23 AM27 AM29 AM32 AM32 AM45
251~300 351~400
301~350 AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28 401~450 AM20 AM21 AM20 AM21 AM21 AM23 AM25 AM26 AM30 AM33 AM33 AM48
AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26 AM18 AM19 AM18 AM19 AM19 AM21 AM23 AM24 AM27 AM30 AM30 AM44
351~400 AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28 451~500 AM20 AM21 AM20 AM21 AM21 AM23 AM25 AM26 AM30 AM33 AM33 AM48
AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26 AM18 AM19 AM18 AM19 AM19 AM21 AM23 AM24 AM27 AM30 AM30 AM44
401~450 AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28
AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26
451~500 AM12 AM13 AM11 AM12 AM12 AM13 AM14 AM15 AM18 AM21 AM21 AM28
AM11 AM12 AM10 AM11 AM11 AM12 AM13 AM14 AM17 AM19 AM19 AM26
1171 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1172
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED PLATES -ALP- FINISHED PLATES
-SIZE SPECIFIED TYPE- -ALTERATION GUIDE-
ALP(Size specified type) The volume discount rate is also applicable to alteration cost. P.39
A 99mm or less 100~250mm 251mm or more Alteration Available for size specified and economy type only.
(1mm increments) B
DimensionACB +0.4 +0.5 +0.8
tolerance000
T
BC+0.5
BT+0.3
Alterations Code Spec. \/1Code
A BC \/1P
Changes width(Dimension B)
T 20~ 59 400
TC 20¯BC¯299 61~ 79 500
81~ 99 600
When BC¯29, A is 250 or less. T (BC) 101~199 800
20 BC195 201~299 1,000
BC 1mm increments BC195 13 BC248
(ex.)B=195
B \/1P
Catalog No. A B
25~ 60 800
Precision standards P.1158 A7075P-T651 S-SKD 305 200 61~ 80 1,000
(Ultra high strength duralumin plate) E-SKD 365 250 81~100 1,200
T (CNC) 101~200 1,600
Catalog No. A BT IVolume discount rate P.37 To be quoted on Changes all around chamfering 20 CNC 201~300 2,000
ALP 120 60 25 price & lead time 13 CNC
Order Price Quantity 1~9 10~30 above Max. Q'ty.
5%
Rate - C0.5~C1.0 e ~C0.1
3Delivery Days Express A 800/1Pc. P.38 Alteration P.1174(Dimension B changeable) Not applicable to ALP
A flat charge of 2,160 yen for 3 pieces or more of the same size. CNC (ex.)
Catalog No.
U/Price U/Price A B
200
A(1mm incr.) B T 10 15 20 25 30 35 40 50 A(1mm incr.) B T 10 15 20 25 30 35 40 50 S-SKD 305 250
E-SKD 365
25~100 25 4,700 4,700 4,700 100~150 5,880 6,220 7,260 8,350 9,440 10,530 11,630 13,810
101~250 5,140 5,140 5,140
151~180 5,880 6,850 8,100 9,400 10,710 12,010 13,300 15,910
30~100 4,700 4,700 4,700 181~200 5,880 7,280 8,650 10,100 11,540 12,980 14,430 17,320
101~200 40 5,000 5,000 5,000 201~210 5,970 7,480 8,940 10,440 11,960 13,480 14,990 18,010 Changes the thickness B \/1P
201~400 5,440 5,440 5,820 211~250 150 6,530 8,330 10,050 11,840 13,640 15,440 17,230 20,820 5¯TC<Tmax
251~300 8,550 10,710 12,760 14,910 17,050 19,200 21,360 25,650 1mm increments
30~ 60 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 25~ 60 1,000
Not applicable to ALP
61~ 80 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,000 301~350 9,700 12,200 14,600 17,100 19,600 22,090 24,590 29,590 61~ 80 1,250
81~100 5,000 5,000 5,000 5,000 5,000 5,000 5,000 5,140 351~400 10,990 13,840 16,580 19,430 22,280 25,130 27,980 33,690 81~100 1,500
T (TC) 101~200 1,750
101~200 60 5,000 5,000 5,000 5,000 5,000 6,270 6,870 8,080 401~450 11,840 15,040 18,120 21,320 24,520 27,720 30,930 37,340 TC (ex.)T=18 TC18
201~300 5,800 5,880 5,880 7,420 8,310 9,200 10,100 11,880 451~500 13,130 16,690 20,100 23,650 27,210 30,760 34,310 41,430 Catalog No. A B
301~400 6,460 7,090 8,280 9,460 10,650 11,840 13,030 15,400 100~160 5,880 6,620 7,870 9,090 10,300 11,550 12,760 15,240
401~500 6,930 8,410 9,890 11,380 12,850 14,340 15,820 18,780 161~200 6,010 7,520 9,080 10,580 12,080 13,640 15,150 18,220 S-SKD 305 200 20 TC18 201~300 2,000
30~ 80 5,440 5,440 5,440 5,440 5,440 5,440 5,440 5,770 201~250 6,760 8,630 10,580 12,450 14,320 16,250 18,120 21,940 E-SKD 365 250 13 TC12
81~100 5,440 5,440 5,440 5,440 5,440 5,440 5,740 6,540 251~300 160 8,830 11,060 13,390 15,620 17,860 20,190 22,420 26,990
301~350 10,010 12,620 15,330 17,920 20,530 23,240 25,840 31,160
101~125 5,440 5,440 5,440 5,440 5,520 6,010 6,510 7,500 Changes the thickness tolerance B \/1P
126~150 80 5,440 5,440 5,440 5,460 6,100 6,680 7,280 8,460 351~400 11,350 14,320 17,410 20,380 23,350 26,440 29,410 35,470
151~160 5,440 5,440 5,440 5,650 6,330 6,960 7,580 8,840
401~450 12,240 15,580 19,050 22,390 25,720 29,190 32,530 39,340 HPMCSCCSS EEEEE T +0.3
+0.1
161~200 5,440 5,440 5,630 6,410 7,250 8,030 8,820 10,380 451~500 13,580 17,290 21,140 24,830 28,540 32,390 36,100 43,650 +0.80
+0.51
201~250 6,760 6,760 6,400 7,360 8,410 9,390 10,360 12,300 100~200 7,020 8,950 10,820 12,730 14,600 16,530 18,450 22,240 SKDCDCCSKSCSK EE T +0.5 25~ 60 400
+0.2 T 61~ 80 500
251~500 8,850 10,770 12,700 14,620 16,700 18,630 20,550 24,400 201~250 7,950 10,340 12,670 15,050 17,370 19,770 22,160 26,880 20 81~100 600
13 101~200 800
30~100 5,720 5,720 5,720 5,720 5,780 6,270 6,770 7,780 251~300 10,330 13,200 15,980 18,840 21,610 24,480 27,340 32,970 TKC Not applicable to ALP 201~300 1,000
101~125 5,720 5,720 5,720 5,890 6,490 7,100 7,720 8,970 301~350 200 11,850 15,180 18,410 21,740 24,970 28,310 31,630 38,200
126~150 5,720 5,720 5,750 6,480 7,210 7,940 8,660 10,160 351~400 13,220 17,020 20,700 24,500 28,190 31,980 35,790 43,270 (ex.)
Catalog No.
151~160 5,720 5,720 5,940 6,710 7,500 8,270 9,040 10,640 401~450 14,430 18,700 22,840 27,110 31,240 35,520 39,790 48,200 S-SKD A B (TKC)
E-SKD 305 200 TKC
161~180 5,720 5,720 6,320 7,190 8,060 8,930 9,790 11,590 451~500 15,790 20,540 25,130 29,870 34,460 39,200 43,940 53,280 365 250 TKC
181~200 5,720 5,750 6,700 7,670 8,630 9,590 10,550 12,530 100~200 8,280 10,620 12,970 15,320 17,730 20,070 22,410 27,160
201~210 100 5,880 6,030 7,040 8,050 9,060 10,070 11,080 13,160 201~250 9,430 12,360 15,270 18,190 21,180 24,090 27,020 32,930
211~250 6,160 6,900 8,100 9,300 10,490 11,690 12,890 15,350 251~300 12,360 15,840 19,330 22,830 26,400 29,890 33,380 40,450
251~300 6,760 8,210 9,640 11,070 12,500 13,930 15,360 18,320 301~350 250 13,950 18,010 22,080 26,140 30,310 34,370 38,430 46,660
301~350 7,590 9,370 11,040 12,700 14,360 16,030 17,690 21,140 351~400 15,700 20,330 24,960 29,610 34,360 38,990 43,620 53,000
351~400 8,510 10,520 12,420 14,330 16,230 18,120 20,020 23,950 401~450 17,000 22,210 27,420 32,620 37,970 43,170 48,370 58,910 3Delivery Days Express A 800/1Pc. P.38
401~450 9,270 11,530 13,680 15,810 17,950 20,080 22,210 26,610 451~500 18,750 24,520 30,310 36,080 42,010 47,790 53,560 65,270 A flat charge of 2,160 yen for 3 pieces or more of the same size.
451~500 10,180 12,700 15,060 17,440 19,800 22,170 24,550 29,430 100~200 9,480 12,300 15,130 17,960 20,780 23,610 26,440 32,080
50~125 5,880 5,880 5,990 6,760 7,520 8,280 9,050 10,560 201~300 12,240 16,440 20,640 24,840 29,060 33,260 37,460 45,870
126~150 5,880 5,880 6,580 7,480 8,400 9,310 10,210 12,040 301~350 300 16,110 20,990 25,890 30,780 35,680 40,570 45,470 55,260 Price Price=Unit price of size specified type+Alteration fee
351~400 17,920 23,500 29,090 34,680 40,250 45,840 51,430 62,590
151~160 5,880 5,880 6,810 7,780 8,750 9,720 10,690 12,620
161~180 5,880 6,200 7,290 8,360 9,450 10,540 11,620 13,800 401~450 19,600 25,870 32,140 38,420 44,690 50,960 57,240 69,780
181~200 5,880 6,550 7,750 8,960 10,160 11,360 12,570 14,960 451~500 21,410 28,370 35,340 42,300 49,260 56,230 63,190 77,110
201~210 125 6,160 7,020 8,280 9,540 10,810 12,060 13,330 15,840
211~250 6,520 8,010 9,510 11,000 12,500 14,000 15,490 18,480
251~300 7,550 9,330 11,130 12,920 14,700 16,490 18,290 21,860
301~350 8,720 10,810 12,890 14,960 17,050 19,130 21,210 25,380
351~400 9,750 12,130 14,500 16,880 19,250 21,630 24,010 28,760
401~450 10,630 13,290 15,970 18,640 21,300 23,970 26,650 31,980
451~500 11,650 14,610 17,580 20,540 23,500 26,470 29,430 35,360
1173 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1174
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED BLOCKS FINISHED BLOCKS
-PRICE-
The volume discount rate is also applicable to alteration cost. P.39
IFB-SKH (SKH51) U/Price IVolume discount rate P.37
A +0.3 T +0.3 Price Quantity 1~9 10~30
+0.2 +0.2 Rate - 5%
To be quoted on price & lead time above Max. Q'ty.
6.3 U/Price
6.3 Precision standards A TB 30~40 41~50 51~60 61~70 71~80 81~90 91~100
CPerpendicularity:Max. 0.02 per 100mm 30~40
+0.3 CParallelism between upper and lower surface:Max. 0.02 per 100mm 41~50 8~13 5,450 5,940 6,430 6,900 7,190 7,560 7,830
+0.2 CFlatness of upper and lower surface:Max. 0.04 per 100mm 51~60 14~16 5,560 6,090 6,610 7,100 7,420 7,830 8,120
CAlteration of circumferential chamfering C(o no chamfering) 61~70 17~20 5,680 6,230 6,780 7,300 7,650 8,090 8,400
B CSurface roughness : Max. 6.3a(Milling) 71~80 21~25 5,800 6,380 6,960 7,510 7,880 8,350 8,690
81~90 26~30 6,030 6,670 7,300 7,910 8,350 8,870 9,270
6.3 6.3 6.3 91~100 31~40 6,150 6,920 7,920 8,250 8,820 9,400 9,900
41~50 6,670 7,500 8,520 8,820 9,680 10,580 11,300
6.3 51~60 7,200 8,020 9,400 9,680 10,580 12,150 13,200
5,940 6,810 7,130 7,510 7,880 8,090 8,400
SKH51(Raw material) Catalog No. A 1mm increments T 8~13 6,090 6,960 7,300 7,710 8,120 8,350 8,690
SKD11(Raw material) 30~100 B 8~60 14~16 6,230 7,100 7,480 7,910 8,350 8,610 8,980
DC53(Raw material) FB-SKH 17~20 6,380 7,250 7,650 8,120 8,580 8,870 9,270
SKS3(Raw material) FB-SKD 30~200 30~100 35~60 21~25 6,670 7,680 8,170 8,720 9,270 9,650 10,140
SKS9(3 Raw material) FB-DC 26~30 6,920 8,100 8,370 8,660 9,500 10,070 11,090
S50C(Raw material) FB-SKS 30~200 31~40 7,500 8,930 9,230 9,500 10,800 11,580 12,820
FB-SK 41~50 8,020 9,800 10,280 10,690 12,420 13,390 14,360
FB-SC 51~60 6,430 7,130 7,650 7,910 8,120 8,350 8,690
6,610 7,300 8,000 8,320 8,580 8,870 9,270
Order Catalog No. A BT Price FB-SKH P.1176 8~13 6,780 7,480 8,170 8,520 8,810 9,130 9,560
FB-SKD 150 170 55 FB-SKDCFB-DC P.1177 14~16 6,960 7,650 8,350 8,720 9,040 9,390 9,850
FB-SKS P.1178 17~20 7,300 8,170 8,870 9,330 9,740 10,170 11,020
Delivery 3 Days Express A 800/1Pc. P.38 FB-SK P.1179 21~25 7,920 8,370 9,220 9,500 10,150 11,770 12,090
Alteration FB-SC P.1180 26~30 8,520 9,230 9,800 10,850 11,930 13,600 14,040
A flat charge of 2,160 yen for 3 pieces or 31~40 9,400 10,280 10,850 12,150 13,470 15,740 17,110
more of the same size. 41~50 6,900 7,510 7,910 8,120 8,350 8,610 8,980
51~60 7,100 7,710 8,320 8,520 8,810 9,130 9,560
Order Catalog No. A-B-T (KACCTACCCAC) 7,300 7,910 8,520 8,930 9,740 9,650 10,140
8~13 7,510 8,120 8,720 9,740 10,200 10,700 11,310
FB-SKD 80 - 95 - 45 CAC 14~16 7,910 8,720 9,330 10,140 10,670 11,220 11,890
FB-SKS 110 - 76 - 52 KAC 17~20 8,250 8,660 9,500 10,890 11,740 12,250 12,600
FB-SKH 30 - 59 - 16 TAC 21~25 8,820 9,500 10,850 11,820 13,500 13,720 14,500
26~30 9,680 10,690 12,150 13,470 15,750 16,450 16,600
Delivery 3 Days Express A 800/1Pc. P.38 31~40 7,190 7,880 8,120 8,350 8,810 8,870 9,270
41~50 7,420 8,120 8,580 8,810 9,510 9,650 10,140
A flat charge of 2,160 yen for 3 pieces or more of the same size. 51~60 7,650 8,350 8,810 9,740 9,970 10,170 10,730
7,880 8,580 9,040 10,200 10,900 11,220 11,890
Price Finished blocks Unit price+Alteration fe(e \/1Code) 8~13 8,350 9,270 9,740 10,670 11,360 11,740 12,470
14~16 8,820 9,500 10,150 11,740 12,170 13,070 14,250
Adds reference plane Grinds upper and lower surface Changes all around chamfering 17~20 9,680 10,800 11,930 13,500 14,170 15,250 16,420
A 21~25 10,580 12,420 13,470 15,750 16,200 17,420 18,620
G C0.5~1 26~30 7,560 8,090 8,350 8,610 8,870 9,130 9,560
Alterations 1.6 31~40 7,830 8,350 8,870 9,130 9,650 9,910 10,440
41~50 8,090 8,610 9,130 9,650 10,170 10,440 11,020
G C0.5~1 51~60 8,350 8,870 9,390 10,700 11,220 11,480 12,180
1.6 8,870 9,650 10,170 11,220 11,740 12,000 12,760
CAC 8~13 9,400 10,070 11,770 12,250 13,070 14,570 15,020
B Chamfers the all circumferences 14~16 10,580 11,580 13,600 13,720 15,250 17,050 17,920
T by C0.5~1.0 17~20 12,150 13,390 15,740 16,450 17,420 19,450 20,270
21~25 7,830 8,400 8,690 8,980 9,270 9,560 9,850
1.6 1.6 1,000 26~30 8,120 8,690 9,270 9,560 10,140 10,440 10,730
G (6.3S) G (6.3S) 31~40 8,400 8,980 9,560 10,140 10,730 11,020 11,310
41~50 8,690 9,270 9,850 11,310 11,890 12,180 12,470
Reference plane 51~60 9,270 10,140 11,020 11,890 12,470 12,760 13,050
9,900 11,090 12,090 12,600 14,250 15,020 15,550
Code KAC TAC 8~13 11,300 12,820 14,040 14,500 16,420 17,920 17,870
14~16 13,200 14,360 17,110 16,600 18,620 20,270 20,570
Reference plane is added to the Upper and lower surface is finished by grinding. 17~20
direction of the dimension A and B. 21~25
26~30
31~40
41~50
51~60
Spec. Perpendicularity of reference plane Parallelism between upper and lower surface:
Max. 0.015 per 100mm Max. 0.012 per 100mm
Flatness of upper and lower surface:
T Max. 25 Min. 26
Per 100mm 0.015 0.012
\/1Code 1,500 1,300
1175 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1176
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED BLOCKS
-PRICE-
IFB-SKD (SKD11) U/Price IVolume discount rate P.37 IFB-SKS (SKS3) U/Price IVolume discount rate P.37
Price IFB-DC (DC53) U/Price
Quantity 1~9 10~30 Price Quantity 1~9 10~30
Rate - 5% Rate - 5%
To be quoted on price & lead time above Max. Q'ty. To be quoted on price & lead time above Max. Q'ty.
A B U/Price A B U/Price
30~ 40 T 30~ 40 T
41~ 50 30~ 41~ 51~ 61~ 71~ 81~ 91~ 101~ 111~ 121~ 131~ 141~ 151~ 161~ 171~ 181~ 191~ 41~ 50 30~ 41~ 51~ 61~ 71~ 81~ 91~ 101~ 111~ 121~ 131~ 141~ 151~ 161~ 171~ 181~ 191~
51~ 60 35~40 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 51~ 60 35~40 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200
61~ 70 41~50 61~ 70 41~50
71~ 80 51~60 2,460 2,770 2,880 3,000 3,210 3,420 3,600 3,660 4,060 4,180 4,350 4,560 4,780 4,930 4,980 5,130 5,910 71~ 80 51~60 1,640 1,850 1,920 2,000 2,140 2,280 2,400 2,440 2,710 2,790 2,900 3,040 3,190 3,290 3,320 3,420 3,940
81~ 90 35~40 2,670 3,000 3,100 3,210 3,520 3,850 4,110 4,420 4,560 4,930 5,260 5,550 5,620 5,850 5,880 6,060 6,910 81~ 90 35~40 1,780 2,000 2,070 2,140 2,350 2,570 2,740 2,950 3,040 3,290 3,510 3,700 3,750 3,900 3,920 4,040 4,610
91~100 41~50 2,880 3,210 3,420 3,520 3,850 4,420 4,800 4,990 5,260 5,580 6,040 6,180 6,370 6,610 6,670 6,900 7,920 91~100 41~50 1,920 2,140 2,280 2,350 2,570 2,950 3,200 3,330 3,510 3,720 4,030 4,120 4,250 4,410 4,450 4,600 5,280
101~110 51~60 2,770 3,000 3,100 3,210 3,520 3,730 4,110 4,530 4,560 5,040 5,260 5,470 5,680 5,730 5,980 6,210 6,520 101~110 51~60 1,850 2,000 2,070 2,140 2,350 2,490 2,740 3,020 3,040 3,360 3,510 3,650 3,790 3,820 3,990 4,140 4,350
111~120 35~40 3,000 3,310 3,420 3,520 4,000 4,290 4,750 5,320 5,430 5,910 6,370 6,520 6,700 6,780 7,000 7,230 7,920 111~120 35~40 2,000 2,210 2,280 2,350 2,670 2,860 3,170 3,550 3,620 3,940 4,250 4,350 4,470 4,520 4,670 4,820 5,280
121~130 41~50 3,210 3,630 3,810 3,960 4,600 4,960 5,320 6,000 6,180 6,690 7,450 7,540 7,650 7,750 ,8,010 8,260 8,820 121~130 41~50 2,140 2,420 2,540 2,640 3,070 3,310 3,550 4,000 4,120 4,460 4,970 5,030 5,100 5,170 5,340 5,510 5,880
131~140 51~60 2,880 3,100 3,210 3,520 3,760 4,360 4,480 4,930 5,280 5,820 5,890 6,420 6,480 6,690 6,840 6,910 7,320 131~140 51~60 1,920 2,070 2,140 2,350 2,510 2,910 2,990 3,290 3,520 3,880 3,930 4,280 4,320 4,460 4,560 4,610 4,880
141~150 35~40 3,100 3,420 3,630 4,020 4,420 5,040 5,200 5,770 6,180 6,780 6,880 7,300 7,600 7,800 8,040 8,100 8,610 141~150 35~40 2,070 2,280 2,420 2,680 2,950 3,360 3,470 3,850 4,120 4,520 4,590 4,870 5,070 5,200 5,360 5,400 5,740
151~160 41~50 3,420 3,810 4,020 4,500 4,990 5,830 6,340 6,640 7,240 7,770 7,890 8,400 8,710 8,850 9,030 9,190 9,780 151~160 41~50 2,280 2,540 2,680 3,000 3,330 3,890 4,230 4,430 4,830 5,180 5,260 5,600 5,810 5,900 6,020 6,130 6,520
161~170 51~60 3,000 3,210 3,520 3,630 4,270 4,900 5,040 5,670 6,010 6,450 6,780 6,910 7,420 7,590 7,750 7,840 8,230 161~170 51~60 2,000 2,140 2,350 2,420 2,850 3,270 3,360 3,780 4,010 4,300 4,520 4,610 4,950 5,060 5,170 5,230 5,490
171~180 35~40 3,210 3,520 4,020 4,300 5,050 5,490 5,800 6,630 7,200 7,500 8,110 8,200 8,640 8,920 9,120 9,220 9,690 171~180 35~40 2,140 2,350 2,680 2,870 3,370 3,660 3,870 4,420 4,800 5,000 5,410 5,470 5,760 5,950 6,080 6,150 6,460
181~190 41~50 3,520 3,960 4,500 4,900 5,730 6,580 6,640 7,590 7,990 8,080 8,950 9,180 9,880 10,090 10,350 10,500 11,070 181~190 41~50 2,350 2,640 3,000 3,270 3,820 4,390 4,430 5,060 5,330 5,390 5,970 6,120 6,590 6,730 6,900 7,000 7,380
191~200 51~60 3,210 3,520 3,760 4,270 4,870 5,230 5,700 6,370 6,630 7,020 7,170 7,620 8,370 8,620 8,760 8,880 9,400 191~200 51~60 2,140 2,350 2,510 2,850 3,250 3,490 3,800 4,250 4,420 4,680 4,780 5,080 5,580 5,750 5,840 5,920 6,270
35~40 3,520 4,000 4,420 5,050 5,670 6,100 6,570 7,200 7,480 8,250 8,380 8,890 9,640 10,000 10,200 10,360 10,860 35~40 2,350 2,670 2,950 3,370 3,780 4,070 4,380 4,800 4,990 5,500 5,590 5,930 6,430 6,670 6,800 6,910 7,240
41~50 3,850 4,600 4,990 5,730 6,480 6,970 7,450 8,250 8,560 9,460 9,720 10,260 11,110 11,280 11,440 11,530 11,700 41~50 2,570 3,070 3,330 3,820 4,320 4,650 4,970 5,500 5,710 6,310 6,480 6,840 7,410 7,520 7,630 7,690 7,800
51~60 3,420 3,730 4,360 4,900 5,230 5,830 6,010 6,870 7,270 7,840 8,340 8,800 8,890 9,150 9,480 9,810 10,120 51~60 2,280 2,490 2,910 3,270 3,490 3,890 4,010 4,580 4,850 5,230 5,560 5,870 5,930 6,100 6,320 6,540 6,750
35~40 3,850 4,290 5,040 5,490 6,100 6,820 7,170 7,930 8,550 9,180 9,580 10,260 10,380 10,600 10,900 11,490 11,830 35~40 2,570 2,860 3,360 3,660 4,070 4,550 4,780 5,290 5,700 6,120 6,390 6,840 6,920 7,070 7,270 7,660 7,890
41~50 4,420 4,960 5,830 6,580 6,970 7,780 8,110 9,090 9,720 10,480 10,960 11,730 11,830 12,130 12,480 13,050 13,440 41~50 2,950 3,310 3,890 4,390 4,650 5,190 5,410 6,060 6,480 6,990 7,310 7,820 7,890 8,090 8,320 8,700 8,960
51~60 3,600 4,110 4,480 5,040 5,700 6,010 6,220 7,480 7,900 8,670 9,060 9,780 9,990 10,330 10,590 10,720 10,860 51~60 2,400 2,740 2,990 3,360 3,800 4,010 4,150 4,990 5,270 5,780 6,040 6,520 6,660 6,890 7,060 7,150 7,240
35~40 4,110 4,750 5,200 5,800 6,570 7,170 7,150 8,800 9,130 10,080 10,710 11,310 11,460 12,030 12,310 12,450 12,640 35~40 2,740 3,170 3,470 3,870 4,380 4,780 4,770 5,870 6,090 6,720 7,140 7,540 7,640 8,020 8,210 8,300 8,430
41~50 4,800 5,320 6,340 6,640 7,450 8,110 8,230 9,910 10,660 11,500 12,280 12,780 13,020 13,590 13,900 14,190 14,430 41~50 3,200 3,550 4,230 4,430 4,970 5,410 5,490 6,610 7,110 7,670 8,190 8,520 8,680 9,060 9,270 9,460 9,620
51~60 3,660 4,530 4,930 5,670 6,370 6,870 7,480 8,010 8,700 9,370 9,990 10,300 10,720 11,100 11,410 11,790 12,400 51~60 2,440 3,020 3,290 3,780 4,250 4,580 4,990 5,340 5,800 6,250 6,660 6,870 7,150 7,400 7,610 7,860 8,270
35~40 4,420 5,320 5,770 6,630 7,200 7,930 8,800 9,330 10,140 10,920 11,620 12,000 12,480 12,850 13,330 13,740 14,410 35~40 2,950 3,550 3,850 4,420 4,800 5,290 5,870 6,220 6,760 7,280 7,750 8,000 8,320 8,570 8,890 9,160 9,610
41~50 4,990 6,000 6,640 7,590 8,250 9,090 9,910 10,590 11,580 12,540 13,290 13,680 14,250 14,670 15,540 15,690 16,120 41~50 3,330 4,000 4,430 5,060 5,500 6,060 6,610 7,060 7,720 8,360 8,860 9,120 9,500 9,780 10,360 10,460 10,750
51~60 4,060 4,560 5,280 6,010 6,630 7,270 7,900 8,700 9,060 9,780 10,200 10,920 11,550 11,920 12,210 12,400 13,120 51~60 2,710 3,040 3,520 4,010 4,420 4,850 5,270 5,800 6,040 6,520 6,800 7,280 7,700 7,950 8,140 8,270 8,750
35~40 4,560 5,430 6,180 7,200 7,480 8,550 9,130 10,140 10,770 11,830 12,210 13,050 13,500 13,810 14,200 14,490 15,270 35~40 3,040 3,620 4,120 4,800 4,990 5,700 6,090 6,760 7,180 7,890 8,140 8,700 9,000 9,210 9,470 9,660 10,180
41~50 5,260 6,180 7,240 7,990 8,560 9,720 10,660 11,580 12,450 13,560 13,900 14,880 15,370 15,820 16,200 16,500 17,490 41~50 3,510 4,120 4,830 5,330 5,710 6,480 7,110 7,720 8,300 9,040 9,270 9,920 10,250 10,550 10,800 11,000 11,660
51~60 4,180 5,040 5,820 6,450 7,020 7,840 8,670 9,370 9,780 10,080 10,530 11,550 12,160 12,720 13,140 13,410 13,750 51~60 2,790 3,360 3,880 4,300 4,680 5,230 5,780 6,250 6,520 6,720 7,020 7,700 8,110 8,480 8,760 8,940 9,170
35~40 4,930 5,910 6,780 7,500 8,250 9,180 10,080 10,920 11,830 11,850 12,300 13,380 14,160 14,560 15,090 15,600 15,790 35~40 3,290 3,940 4,520 5,000 5,500 6,120 6,720 7,280 7,890 7,900 8,200 8,920 9,440 9,710 10,060 10,400 10,530
41~50 5,580 6,690 7,770 8,080 9,460 10,480 11,500 12,540 13,560 13,750 14,070 15,520 16,150 16,650 17,170 17,790 18,450 41~50 3,720 4,460 5,180 5,390 6,310 6,990 7,670 8,360 9,040 9,170 9,380 10,350 10,770 11,100 11,450 11,860 12,300
51~60 4,350 5,260 5,890 6,780 7,170 8,340 9,060 9,990 10,200 10,530 11,320 12,010 13,030 13,260 13,930 14,320 14,830 51~60 2,900 3,510 3,930 4,520 4,780 5,560 6,040 6,660 6,800 7,020 7,550 8,010 8,690 8,840 9,290 9,550 9,890
35~40 5,260 6,370 6,880 8,110 8,380 9,580 10,710 11,620 12,210 12,300 13,180 14,080 15,150 15,450 16,240 16,690 17,520 35~40 3,510 4,250 4,590 5,410 5,590 6,390 7,140 7,750 8,140 8,200 8,790 9,390 10,100 10,300 10,830 11,130 11,680
41~50 6,040 7,450 7,890 8,950 9,720 10,960 12,280 13,290 13,900 14,070 15,040 15,780 17,320 17,580 18,540 19,080 19,950 41~50 4,030 4,970 5,260 5,970 6,480 7,310 8,190 8,860 9,270 9,380 10,030 10,520 11,550 11,720 12,360 12,720 13,300
51~60 4,560 5,470 6,420 6,910 7,620 8,800 9,780 10,300 10,920 11,550 12,010 12,900 13,500 13,930 14,550 14,860 15,570 51~60 3,040 3,650 4,280 4,610 5,080 5,870 6,520 6,870 7,280 7,700 8,010 8,600 9,000 9,290 9,700 9,910 10,380
35~40 5,550 6,520 7,300 8,200 8,890 10,260 11,310 12,000 13,050 13,380 14,080 15,190 15,730 16,180 16,500 17,350 18,490 35~40 3,700 4,350 4,870 5,470 5,930 6,840 7,540 8,000 8,700 8,920 9,390 10,130 10,490 10,790 11,000 11,570 12,330
41~50 6,180 7,540 8,400 9,180 10,260 11,730 12,780 13,680 14,880 15,520 15,780 16,680 17,950 18,580 19,350 19,750 21,240 41~50 4,120 5,030 5,600 6,120 6,840 7,820 8,520 9,120 9,920 10,350 10,520 11,120 11,970 12,390 12,900 13,170 14,160
51~60 4,780 5,680 6,480 7,420 8,370 8,890 9,990 10,720 11,550 12,160 13,030 13,500 14,370 15,240 15,540 15,840 16,240 51~60 3,190 3,790 4,320 4,950 5,580 5,930 6,660 7,150 7,700 8,110 8,690 9,000 9,580 10,160 10,360 10,560 10,830
35~40 5,620 6,700 7,600 8,640 9,640 10,380 11,460 12,480 13,500 14,160 15,150 15,730 16,690 17,740 18,060 18,430 19,600 35~40 3,750 4,470 5,070 5,760 6,430 6,920 7,640 8,320 9,000 9,440 10,100 10,490 11,130 11,830 12,040 12,290 13,070
41~50 6,370 7,650 8,710 9,880 11,110 11,830 13,020 14,250 15,370 16,150 17,320 17,950 19,090 20,160 20,530 21,000 22,360 41~50 4,250 5,100 5,810 6,590 7,410 7,890 8,680 9,500 10,250 10,770 11,550 11,970 12,730 13,440 13,690 14,000 14,910
51~60 4,930 5,730 6,690 7,590 8,620 9,150 10,330 11,100 11,920 12,720 13,260 13,930 15,240 15,940 16,390 16,510 17,530 51~60 3,290 3,820 4,460 5,060 5,750 6,100 6,890 7,400 7,950 8,480 8,840 9,290 10,160 10,630 10,930 11,010 11,690
35~40 5,850 6,780 7,800 8,920 10,000 10,600 12,030 12,850 13,810 14,560 15,450 16,180 17,740 18,150 18,430 19,240 20,370 35~40 3,900 4,520 5,200 5,950 6,670 7,070 8,020 8,570 9,210 9,710 10,300 10,790 11,830 12,100 12,290 12,830 13,580
41~50 6,610 7,750 8,850 10,090 11,280 12,130 13,590 14,670 15,820 16,650 17,580 18,580 20,160 20,430 20,790 21,970 23,200 41~50 4,410 5,170 5,900 6,730 7,520 8,090 9,060 9,780 10,550 11,100 11,720 12,390 13,440 13,620 13,860 14,650 15,470
51~60 4,980 5,980 6,840 7,750 8,760 9,480 10,590 11,410 12,210 13,140 13,930 14,550 15,540 16,390 16,560 17,490 18,330 51~60 3,320 3,990 4,560 5,170 5,840 6,320 7,060 7,610 8,140 8,760 9,290 9,700 10,360 10,930 11,040 11,660 12,220
35~40 5,880 7,000 8,040 9,120 10,200 10,900 12,310 13,330 14,200 15,090 16,240 16,500 18,060 18,430 18,480 20,310 21,240 35~40 3,920 4,670 5,360 6,080 6,800 7,270 8,210 8,890 9,470 10,060 10,830 11,000 12,040 12,290 12,320 13,540 14,160
41~50 6,670 8,010 9,030 10,350 11,440 12,480 13,900 15,540 16,200 17,170 18,540 19,350 20,530 20,790 21,030 23,130 24,210 41~50 4,450 5,340 6,020 6,900 7,630 8,320 9,270 10,360 10,800 11,450 12,360 12,900 13,690 13,860 14,020 15,420 16,140
51~60 5,130 6,210 6,910 7,840 8,880 9,810 10,720 11,790 12,400 13,410 14,320 14,860 15,840 16,510 17,490 18,120 19,000 51~60 3,420 4,140 4,610 5,230 5,920 6,540 7,150 7,860 8,270 8,940 9,550 9,910 10,560 11,010 11,660 12,080 12,670
35~40 6,060 7,230 8,100 9,220 10,360 11,490 12,450 13,740 14,490 15,600 16,690 17,350 18,430 19,240 20,310 21,090 22,120 35~40 4,040 4,820 5,400 6,150 6,910 7,660 8,300 9,160 9,660 10,400 11,130 11,570 12,290 12,830 13,540 14,060 14,750
41~50 6,900 8,260 9,190 10,500 11,530 13,050 14,190 15,690 16,500 17,790 19,080 19,750 21,000 21,970 23,130 24,040 25,270 41~50 4,600 5,510 6,130 7,000 7,690 8,700 9,460 10,460 11,000 11,860 12,720 13,170 14,000 14,650 15,420 16,030 16,850
51~60 5,910 6,520 7,320 8,230 9,400 10,120 10,860 12,400 13,120 13,750 14,830 15,570 16,240 17,530 18,330 19,000 19,950 51~60 3,940 4,350 4,880 5,490 6,270 6,750 7,240 8,270 8,750 9,170 9,890 10,380 10,830 11,690 12,220 12,670 13,300
6,910 7,920 8,610 9,690 10,860 11,830 12,640 14,410 15,270 15,790 17,520 18,490 19,600 20,370 21,240 22,120 23,160 4,610 5,280 5,740 6,460 7,240 7,890 8,430 9,610 10,180 10,530 11,680 12,330 13,070 13,580 14,160 14,750 15,440
7,920 8,820 9,780 11,070 11,700 13,440 14,430 16,120 17,490 18,450 19,950 21,240 22,360 23,200 24,210 25,270 26,410 5,280 5,880 6,520 7,380 7,800 8,960 9,620 10,750 11,660 12,300 13,300 14,160 14,910 15,470 16,140 16,850 17,610
1177 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1178
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
FINISHED BLOCKS
-PRICE-
IFB-SK (SKS93) U/Price IVolume discount rate P.37 IFB-SC (S50C) U/Price IVolume discount rate P.37
Price Quantity 1~9 10~30 Price Quantity 1~9 10~30
Rate - 5% Rate - 5%
To be quoted on price & lead time above Max. Q'ty. To be quoted on price & lead time above Max. Q'ty.
A B U/Price A B U/Price
30~ 40 T 30~ 40 T
41~ 50 30~ 41~ 51~ 61~ 71~ 81~ 91~ 101~ 111~ 121~ 131~ 141~ 151~ 161~ 171~ 181~ 191~ 41~ 50 30~ 41~ 51~ 61~ 71~ 81~ 91~ 101~ 111~ 121~ 131~ 141~ 151~ 161~ 171~ 181~ 191~
51~ 60 35~40 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 51~ 60 35~40 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200
61~ 70 41~50 61~ 70 41~50
71~ 80 51~60 1,140 1,290 1,340 1,400 1,490 1,590 1,680 1,700 1,890 1,950 2,030 2,120 2,230 2,300 2,320 2,390 2,750 71~ 80 51~60 1,140 1,290 1,340 1,400 1,430 1,520 1,600 1,630 1,700 1,750 1,820 1,910 1,970 2,030 2,050 2,080 2,360
81~ 90 35~40 1,240 1,400 1,440 1,490 1,640 1,790 1,910 2,060 2,120 2,300 2,450 2,590 2,620 2,730 2,740 2,820 3,220 81~ 90 35~40 1,240 1,400 1,440 1,490 1,570 1,720 1,830 1,850 1,910 2,070 2,210 2,330 2,340 2,410 2,430 2,460 2,760
91~100 41~50 1,340 1,490 1,590 1,640 1,790 2,060 2,240 2,330 2,450 2,600 2,820 2,880 2,970 3,080 3,110 3,220 3,690 91~100 41~50 1,340 1,490 1,590 1,640 1,720 1,970 2,140 2,160 2,210 2,340 2,530 2,590 2,630 2,730 2,750 2,800 3,160
101~110 51~60 1,290 1,400 1,440 1,490 1,640 1,740 1,910 2,110 2,120 2,350 2,450 2,550 2,650 2,670 2,790 2,890 3,040 101~110 51~60 1,290 1,400 1,440 1,470 1,570 1,660 1,830 1,900 1,910 2,110 2,210 2,260 2,340 2,360 2,430 2,480 2,560
111~120 35~40 1,400 1,540 1,590 1,640 1,860 2,000 2,210 2,480 2,530 2,750 2,970 3,040 3,120 3,160 3,260 3,370 3,690 111~120 35~40 1,400 1,540 1,590 1,620 1,780 1,910 2,120 2,230 2,280 2,480 2,670 2,690 2,770 2,800 2,840 2,890 3,110
121~130 41~50 1,490 1,690 1,770 1,840 2,140 2,310 2,480 2,800 2,880 3,120 3,470 3,520 3,570 3,610 3,730 3,850 4,110 121~130 41~50 1,490 1,690 1,770 1,820 2,050 2,210 2,370 2,520 2,590 2,800 3,130 3,140 3,160 3,200 3,250 3,300 3,460
131~140 51~60 1,340 1,440 1,490 1,640 1,750 2,030 2,090 2,300 2,460 2,710 2,750 2,990 3,020 3,120 3,190 3,220 3,410 131~140 51~60 1,340 1,440 1,490 1,570 1,680 1,940 2,000 2,070 2,210 2,440 2,470 2,650 2,670 2,720 2,730 2,760 2,830
141~150 35~40 1,440 1,590 1,690 1,870 2,060 2,350 2,420 2,690 2,880 3,160 3,210 3,400 3,540 3,640 3,750 3,780 4,010 141~150 35~40 1,440 1,590 1,690 1,790 1,970 2,250 2,320 2,420 2,590 2,840 2,890 3,010 3,140 3,170 3,210 3,240 3,320
151~160 41~50 1,590 1,770 1,870 2,100 2,330 2,720 2,960 3,100 3,380 3,620 3,680 3,920 4,060 4,130 4,210 4,290 4,560 151~160 41~50 1,590 1,770 1,870 2,010 2,230 2,600 2,830 2,790 3,040 3,260 3,310 3,470 3,600 3,590 3,610 3,670 3,780
161~170 51~60 1,400 1,490 1,640 1,690 1,990 2,280 2,350 2,640 2,800 3,010 3,160 3,220 3,460 3,540 3,610 3,660 3,840 161~170 51~60 1,400 1,430 1,570 1,620 1,900 2,190 2,250 2,380 2,520 2,700 2,800 2,850 3,010 3,030 3,050 3,080 3,120
171~180 35~40 1,490 1,640 1,870 2,000 2,350 2,560 2,700 3,090 3,360 3,500 3,780 3,820 4,030 4,160 4,250 4,300 4,520 171~180 35~40 1,490 1,570 1,790 1,920 2,250 2,450 2,590 2,780 3,020 3,150 3,350 3,390 3,510 3,570 3,580 3,620 3,680
181~190 41~50 1,640 1,840 2,100 2,280 2,670 3,070 3,100 3,540 3,730 3,770 4,170 4,280 4,610 4,710 4,830 4,900 5,160 181~190 41~50 1,640 1,760 2,010 2,190 2,550 2,940 2,960 3,180 3,350 3,390 3,700 3,790 4,010 4,030 4,070 4,130 4,200
191~200 51~60 1,490 1,640 1,750 1,990 2,270 2,440 2,660 2,970 3,090 3,270 3,340 3,550 3,900 4,020 4,080 4,140 4,380 191~200 51~60 1,430 1,570 1,680 1,900 2,170 2,330 2,540 2,670 2,780 2,940 2,960 3,090 3,340 3,390 3,410 3,430 3,510
35~40 1,640 1,860 2,060 2,350 2,640 2,840 3,060 3,360 3,490 3,850 3,910 4,150 4,500 4,660 4,760 4,830 5,060 35~40 1,570 1,780 1,970 2,250 2,530 2,720 2,930 3,020 3,140 3,460 3,520 3,610 3,850 3,930 3,940 4,000 4,050
41~50 1,790 2,140 2,330 2,670 3,020 3,250 3,470 3,850 3,990 4,410 4,530 4,780 5,180 5,260 5,340 5,380 5,460 41~50 1,720 2,050 2,230 2,550 2,890 3,110 3,320 3,460 3,590 3,970 4,010 4,170 4,370 4,430 4,500 4,530 4,600
51~60 1,590 1,740 2,030 2,280 2,440 2,720 2,800 3,200 3,390 3,660 3,890 4,100 4,150 4,270 4,420 4,570 4,720 51~60 1,520 1,660 1,940 2,190 2,330 2,600 2,680 2,880 3,050 3,290 3,390 3,460 3,490 3,530 3,600 3,660 3,710
35~40 1,790 2,000 2,350 2,560 2,840 3,180 3,340 3,700 3,990 4,280 4,470 4,780 4,840 4,940 5,080 5,360 5,520 35~40 1,720 1,910 2,250 2,450 2,720 3,040 3,100 3,330 3,590 3,850 3,890 4,030 4,080 4,100 4,140 4,280 4,330
41~50 2,060 2,310 2,720 3,070 3,250 3,630 3,780 4,240 4,530 4,890 5,110 5,470 5,520 5,660 5,820 6,090 6,270 41~50 1,970 2,210 2,600 2,940 3,110 3,470 3,620 3,810 4,080 4,400 4,450 4,610 4,650 4,690 4,740 4,870 4,920
51~60 1,680 1,910 2,090 2,350 2,660 2,800 2,900 3,490 3,680 4,040 4,220 4,560 4,660 4,820 4,940 5,000 5,060 51~60 1,600 1,830 2,000 2,250 2,540 2,680 2,780 3,140 3,320 3,520 3,620 3,840 3,860 3,920 3,950 4,000 4,050
35~40 1,910 2,210 2,420 2,700 3,060 3,340 3,330 4,100 4,260 4,700 4,990 5,270 5,340 5,610 5,740 5,810 5,900 35~40 1,830 2,120 2,320 2,590 2,930 3,100 3,190 3,690 3,830 4,090 4,280 4,440 4,430 4,570 4,590 4,640 4,720
41~50 2,240 2,480 2,960 3,100 3,470 3,780 3,840 4,620 4,970 5,360 5,730 5,960 6,070 6,340 6,480 6,620 6,730 41~50 2,140 2,370 2,830 2,960 3,320 3,620 3,670 4,160 4,470 4,670 4,910 5,020 5,030 5,160 5,190 5,290 5,380
51~60 1,700 2,110 2,300 2,640 2,970 3,200 3,490 3,730 4,060 4,370 4,660 4,800 5,000 5,180 5,320 5,500 5,780 51~60 1,630 1,900 2,070 2,380 2,670 2,880 3,140 3,360 3,530 3,750 3,920 3,980 4,070 4,140 4,180 4,240 4,380
35~40 2,060 2,480 2,690 3,090 3,360 3,700 4,100 4,350 4,730 5,090 5,420 5,600 5,820 5,990 6,220 6,410 6,720 35~40 1,850 2,230 2,420 2,780 3,020 3,330 3,690 3,910 4,120 4,360 4,570 4,640 4,740 4,790 4,880 4,940 5,090
41~50 2,330 2,800 3,100 3,540 3,850 4,240 4,620 4,940 5,400 5,850 6,200 6,380 6,650 6,840 7,250 7,320 7,520 41~50 2,160 2,520 2,790 3,180 3,460 3,810 4,160 4,440 4,700 5,010 5,220 5,280 5,410 5,470 5,690 5,750 5,910
51~60 1,890 2,120 2,460 2,800 3,090 3,390 3,680 4,060 4,220 4,560 4,760 5,090 5,390 5,560 5,690 5,780 6,120 51~60 1,700 1,910 2,210 2,520 2,780 3,050 3,320 3,530 3,620 3,840 3,940 4,140 4,310 4,370 4,390 4,420 4,550
35~40 2,120 2,530 2,880 3,360 3,490 3,990 4,260 4,730 5,020 5,520 5,690 6,090 6,300 6,440 6,620 6,760 7,120 35~40 1,910 2,280 2,590 3,020 3,140 3,590 3,830 4,120 4,300 4,570 4,720 4,950 5,040 5,060 5,110 5,160 5,290
41~50 2,450 2,880 3,380 3,730 3,990 4,530 4,970 5,400 5,810 6,320 6,480 6,940 7,170 7,380 7,560 7,700 8,160 41~50 2,210 2,590 3,040 3,350 3,590 4,080 4,470 4,700 4,980 5,240 5,370 5,650 5,740 5,800 5,830 5,880 6,060
51~60 1,950 2,350 2,710 3,010 3,270 3,660 4,040 4,370 4,560 4,700 4,910 5,390 5,670 5,930 6,130 6,250 6,410 51~60 1,750 2,110 2,440 2,700 2,940 3,290 3,520 3,750 3,840 3,890 4,000 4,310 4,460 4,570 4,640 4,690 4,760
35~40 2,300 2,750 3,160 3,500 3,850 4,280 4,700 5,090 5,520 5,530 5,740 6,240 6,600 6,790 7,040 7,280 7,370 35~40 2,070 2,480 2,840 3,150 3,460 3,850 4,090 4,360 4,570 4,660 4,750 4,990 5,190 5,240 5,330 5,400 5,470
41~50 2,600 3,120 3,620 3,770 4,410 4,890 5,360 5,850 6,320 6,410 6,560 7,240 7,530 7,770 8,010 8,300 8,610 41~50 2,340 2,800 3,260 3,390 3,970 4,400 4,670 5,010 5,240 5,310 5,440 5,790 5,920 5,990 6,060 6,160 6,390
51~60 2,030 2,450 2,750 3,160 3,340 3,890 4,220 4,660 4,760 4,910 5,280 5,600 6,080 6,180 6,500 6,680 6,920 51~60 1,820 2,210 2,470 2,800 2,960 3,390 3,620 3,920 3,940 4,000 4,220 4,400 4,690 4,720 4,830 4,960 5,040
35~40 2,450 2,970 3,210 3,780 3,910 4,470 4,990 5,420 5,690 5,740 6,150 6,570 7,070 7,210 7,580 7,790 8,170 35~40 2,210 2,670 2,890 3,350 3,520 3,890 4,280 4,570 4,720 4,750 4,920 5,160 5,450 5,510 5,630 5,780 5,950
41~50 2,820 3,470 3,680 4,170 4,530 5,110 5,730 6,200 6,480 6,560 7,020 7,360 8,080 8,200 8,650 8,900 9,310 41~50 2,530 3,130 3,310 3,700 4,010 4,450 4,910 5,220 5,370 5,440 5,610 5,890 6,230 6,270 6,420 6,610 6,780
51~60 2,120 2,550 2,990 3,220 3,550 4,100 4,560 4,800 5,090 5,390 5,600 6,020 6,300 6,500 6,790 6,930 7,260 51~60 1,910 2,260 2,650 2,850 3,090 3,460 3,840 3,980 4,140 4,310 4,400 4,640 4,770 4,830 5,040 5,050 5,290
35~40 2,590 3,040 3,400 3,820 4,150 4,780 5,270 5,600 6,090 6,240 6,570 7,090 7,340 7,550 7,700 8,090 8,630 35~40 2,330 2,690 3,010 3,390 3,610 4,030 4,440 4,640 4,950 4,990 5,160 5,470 5,550 5,610 5,720 5,900 6,280
41~50 2,880 3,520 3,920 4,280 4,780 5,470 5,960 6,380 6,940 7,240 7,360 7,780 8,370 8,670 9,030 9,210 9,910 41~50 2,590 3,140 3,470 3,790 4,170 4,610 5,020 5,280 5,650 5,790 5,890 6,000 6,340 6,440 6,700 6,710 7,220
51~60 2,230 2,650 3,020 3,460 3,900 4,150 4,660 5,000 5,390 5,670 6,080 6,300 6,700 7,110 7,250 7,390 7,580 51~60 1,970 2,340 2,670 3,010 3,340 3,490 3,860 4,070 4,310 4,460 4,690 4,770 4,980 5,280 5,330 5,380 5,410
35~40 2,620 3,120 3,540 4,030 4,500 4,840 5,340 5,820 6,300 6,600 7,070 7,340 7,790 8,280 8,420 8,600 9,140 35~40 2,340 2,770 3,140 3,510 3,850 4,080 4,430 4,740 5,040 5,190 5,450 5,550 5,780 6,150 6,200 6,260 6,530
41~50 2,970 3,570 4,060 4,610 5,180 5,520 6,070 6,650 7,170 7,530 8,080 8,370 8,910 9,400 9,580 9,800 10,430 41~50 2,630 3,160 3,600 4,010 4,370 4,650 5,030 5,410 5,740 5,920 6,230 6,340 6,610 6,980 7,050 7,140 7,450
51~60 2,300 2,670 3,120 3,540 4,020 4,270 4,820 5,180 5,560 5,930 6,180 6,500 7,110 7,440 7,650 7,700 8,180 51~60 2,030 2,360 2,720 3,030 3,390 3,530 3,920 4,140 4,370 4,570 4,720 4,830 5,280 5,420 5,570 5,610 5,840
35~40 2,730 3,160 3,640 4,160 4,660 4,940 5,610 5,990 6,440 6,790 7,210 7,550 8,280 8,470 8,600 8,980 9,500 35~40 2,410 2,800 3,170 3,570 3,930 4,100 4,570 4,790 5,060 5,240 5,510 5,610 6,150 6,170 6,260 6,540 6,790
41~50 3,080 3,610 4,130 4,710 5,260 5,660 6,340 6,840 7,380 7,770 8,200 8,670 9,400 9,530 9,700 10,250 10,820 41~50 2,730 3,200 3,590 4,030 4,430 4,690 5,160 5,470 5,800 5,990 6,270 6,440 6,980 6,940 7,060 7,470 7,730
51~60 2,320 2,790 3,190 3,610 4,080 4,420 4,940 5,320 5,690 6,130 6,500 6,790 7,250 7,650 7,720 8,160 8,550 51~60 2,050 2,430 2,730 3,050 3,410 3,600 3,950 4,180 4,390 4,640 4,830 5,040 5,330 5,570 5,630 5,830 6,110
35~40 2,740 3,260 3,750 4,250 4,760 5,080 5,740 6,220 6,620 7,040 7,580 7,700 8,420 8,600 8,620 9,470 9,910 35~40 2,430 2,840 3,210 3,580 3,940 4,140 4,590 4,880 5,110 5,330 5,630 5,720 6,200 6,260 6,280 6,770 7,080
41~50 3,110 3,730 4,210 4,830 5,340 5,820 6,480 7,250 7,560 8,010 8,650 9,030 9,580 9,700 9,810 10,790 11,290 41~50 2,750 3,250 3,610 4,070 4,500 4,740 5,190 5,690 5,830 6,060 6,420 6,700 7,050 7,060 7,150 7,710 8,070
51~60 2,390 2,890 3,220 3,660 4,140 4,570 5,000 5,500 5,780 6,250 6,680 6,930 7,390 7,700 8,160 8,450 8,860 51~60 2,080 2,480 2,760 3,080 3,430 3,660 4,000 4,240 4,420 4,690 4,960 5,050 5,380 5,610 5,830 6,040 6,330
35~40 2,820 3,370 3,780 4,300 4,830 5,360 5,810 6,410 6,760 7,280 7,790 8,090 8,600 8,980 9,470 9,840 10,320 35~40 2,460 2,890 3,240 3,620 4,000 4,280 4,640 4,940 5,160 5,400 5,780 5,900 6,260 6,540 6,770 7,030 7,370
41~50 3,220 3,850 4,290 4,900 5,380 6,090 6,620 7,320 7,700 8,300 8,900 9,210 9,800 10,250 10,790 11,220 11,790 41~50 2,800 3,300 3,670 4,130 4,530 4,870 5,290 5,750 5,880 6,160 6,610 6,710 7,140 7,470 7,710 8,010 8,420
51~60 2,750 3,040 3,410 3,840 4,380 4,720 5,060 5,780 6,120 6,410 6,920 7,260 7,580 8,180 8,550 8,860 9,310 51~60 2,360 2,560 2,830 3,120 3,510 3,710 4,050 4,380 4,550 4,760 5,040 5,290 5,410 5,840 6,110 6,330 6,650
3,220 3,690 4,010 4,520 5,060 5,520 5,900 6,720 7,120 7,370 8,170 8,630 9,140 9,500 9,910 10,320 10,800 2,760 3,110 3,320 3,680 4,050 4,330 4,720 5,090 5,290 5,470 5,950 6,280 6,530 6,790 7,080 7,370 7,720
3,690 4,110 4,560 5,160 5,460 6,270 6,730 7,520 8,160 8,610 9,310 9,910 10,430 10,820 11,290 11,790 12,320 3,160 3,460 3,780 4,200 4,600 4,920 5,380 5,910 6,060 6,390 6,780 7,220 7,450 7,730 8,070 8,420 8,800
1179 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1180
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
HARDENED PLATES CARBIDE BLOCK MATERIALS
HPSH Z
HPHE
Rolling direction B
V++01..55
AT L++10..55 H++10..55 V30(HIP)
88~89HRA
Catalog No. Finishing of A/B/T Precision standard Catalog No. H V 3 4 5 6 8 10 13 16 20 100 L
3
HPSH T +0.05 Finishing of A/B/T G Perpendicularity of surfaces A and B 0.02/100mm or less Z 4 40
+0.03 1.6 Flatness of top and bottom surfaces 0.02/100mm or less 5 50
HPHE 6 60
SKH51 57~63HRC +0.05 Perpendicularity of surfaces A and B 0.05/100mm or less 8 70
+0.02 Flatness of top and bottom surfaces
When T¯0.8: T G 10
1.6 When T¯1.5: 0.2/100mm or less 13
Finishing of A/B/T 16
+0.3 When T˘2.0: 0.1/100mm or less 20
When T˘1.0: T +0.1 22
25
A B T Catalog No. U/Price
80 70 Type T Q'ty:1~4 5~9 10~29 30~50
+0.3 +0.3 5,020 4,270
+0.1 +0.1 1 1 4,840 4,770 4,520 4,110
4,740 4,040
100 80 1.3 1.3 4,650 4,590 4,350 3,950
B 1.5 1.5 4,560 4,510 4,270 3,880
70 +1.0
1.8 +0.05 1.8 4,650 4,420 4,190 3,950 Catalog No. V H L 1Delivery Day
0 2 +0.03 4,740 4,040
3 HPSH 2 4,840 4,330 4,100 4,110 Order Z 20 08 70
Price
3 Q'ty:1~4 30~50
2,840 2,560
4 4 2,650 4,420 4,190 2,380 IVolume discount rate P.37
2,460 4,510 4,270 2,210
5 5 2,750 4,590 4,350 2,470 Quantity 1~4 5~9 10~14 15~20
2,840 2,560 Rate - 5% 10% 15%
6 6 2,940 2,640
3,220 2,900
A T Catalog No. 3,510 U/Price 3,150 U/Price Q'ty:1~4 U/Price Q'ty:1~4
3,980 3,580
Type T 4,460 5~9 10~29 4,010 Catalog No. V H L Catalog No. V H L
+1.0 0.5 +0.05 0.5 2,750 2,700 40L 50L 60L 70L 40L 50L 60L 70L
0 0.6 +0.02
80 0.8 0.6 2,570 2,520 3 3 380 380 380 470 3 1,010 1,260 1,490 1,740
0.8 2,380 2,340 3 380 380 500 580 4 1,260 1,570 1,880 2,190
4 420 530 620 740
1 1 2,660 2,610 4 5 1,510 1,880 2,240 2,620
1.5 HPHE 1.5 2,750 2,700 3 410 500 600 720 6 1,760 2,190 2,620 3,060
2 8 2,260 2,820 3,370 3,920
+1.0 +1.0 2 2,850 2,790 5 4 530 620 740 880 16
0 0 3 +0.3
150 60 4 +0.1 3 3,130 3,060 5 600 770 910 1,050 10 2,770 3,440 4,120 4,790
4 3,400 3,330 3 470 580 720 830 13 3,520 4,380 5,260 6,100
5 5 3,860 3,780 4 600 740 880 1,020 16 4,300 5,320 6,360 7,420
5 720 880 1,050 1,240
6 6 4,320 4,240 6 3 1,210 1,490 1,790 2,060
Price To be quoted on price & lead time above Max. Q'ty. 6 830 1,050 1,240 1,430 4 1,510 1,860 2,220 2,600
P.37
Order Catalog No. 3 570 720 860 980 5 1,820 2,220 2,660 3,110
HPSH 1
4 720 880 1,060 1,240 6 2,100 2,600 3,110 3,650
V30 Z 8 5 860 1,060 1,260 1,500 V30 Z 20 8 2,690 3,350 4,020 4,660
6 1,010 1,240 1,500 1,730 10 3,300 4,110 4,900 5,710
1Delivery Day
(2)Example of use of the block punch 8 1,300 1,600 1,910 2,220 13 4,200 5,220 6,240 7,270
Block punch 3 670 850 1,000 1,180 16 5,110 6,340 7,590 8,820
¡Block punch material for tie bar cut, etc. 4 850 1,050 1,260 1,470 20 6,300 7,830 9,380 10,920
¡Backing plate, etc.
Example 10 5 1,020 1,280 1,500 1,750 3 5,780 7,170 8,600 9,990
6 1,180 1,470 1,750 2,040
4 7,220 8,970 10,730 12,500
(1)Processing method 8 1,520 1,890 2,250 2,620 5 8,660 10,780 12,890 14,980
¡WEDM
¡Cutting after the shape machining. 10 1,850 2,320 2,780 3,220 6 10,100 12,560 15,020 17,490
3 850 1,060 1,280 1,500 8 12,980 16,140 19,320 22,470
IC 4 1,070 1,340 1,600 1,870 100 10 15,260 19,010 22,740 24,610
5 1,300 1,600 1,930 2,220 13 19,460 24,190 28,940 31,330
13 6 1,500 1,870 2,250 2,600 16 23,610 29,380 35,130 38,040
8 1,950 2,390 2,860 3,340 20 29,160 36,290 43,400 46,980
10 2,370 2,940 3,510 4,100 22 31,950 39,740 47,540 51,460
13 3,020 3,740 4,460 5,210 25 36,110 44,920 53,730 58,180
1181 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1182
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
HEAT TREATMENT HEAT TREATMENT
-SKH51- -SKD11-
ISummary of quenching for SKH51 IStandard time of heating ISummary of ordinary quenching and hot bath quenching for SKD11 ISummary of tempering for SKD11
1160~1200A Standard time of heating Ordinary quenching GTemperature of tempering(A)
1) When abrasion proof is concerned:150~200A, 60~63HRC
Refer to the Method Thickness Immersed period Secondary 1000~1050A 2) When abrasion proof and toughness are required:200~250A, 57~60HRC
rihgt table. Salt bath (mm) (minutes) Primary preheating Air cooling 3) When especially toughness is required:500A~, 57HRC or less
preheating 800~
Secondary preheating 5 60
850A 10 90 550~ 850A Quenching GTemperature of tempering GTemperature of tempering
20 160 60 minutes or more
30 240 600A 60 minutes or more 25mm
40 280 Approx.30' Approx.30' Tempering 25mm Acirooling
50 300 Acirooling
60 390 Put into the furnace Approx.30' per per
70 420 of 800A or less. per 25mm 25mm 60~80A
80 440
90 495 25mm
Primary preheating Retention time of quenchingM2 When primary preheating is omitted for small 60~80A Room
500~550A parts, preheat at 600 to 800A temperature
(700 to 750A)after gradual heating.
450~550A Gradual cooling Tempering
30min/25mm 30min/25mm
Approx.80A (Hot bath quenching)
Temperature of quenching
Preheating time Hot bath
250~
Primary preheating:500~550A, 30minutes/25mm thickness 300A
Secondary preheating:850A For simple shaped parts with the G Tempering
Retention time of hardeningM2 thickness of 50mm or less or there is
a limitation of equipmentU900A 60~80A
Tertiary preheating:1050A Retention time of quenchingM2. For
Retention time of hardeningM2 small partsUprimary preheating may GUntil inside / outside temperature to
be omitted. become even.
IRetention time of tempering ITempering hardness curve for SKH51 IAppropriate temperature range of quenching SKD11(A) ITempering hardness curve for SKD11
Retention time of tempering 70 Air hardening Oil quenching 70
1160A 1000~1050 980~1030 975A
1180A
Thickness Retention time 1200A 1000A
(mm) of tempering(hr.) 1220A 1025A
1050A
~ 25 1 68 1240A 60
26~ 35 1.5
36~ 64 2 66 IRelation between quenching temperature and hardness for SKD11
65~ 84 3
85~124 4 64 Appropriate temperature
125~184 5 range for quenching
185~249 6 62 68 A.C A.C:Air hardening
250~349 7 O.Q O.Q:Oil quenching
350~499 8 60
66
58 500 520 540 560 580 600 620Hardness(HRC) 50
Temperature of tempering(A)
Hardness(HRC)64
Hardness(HRC)
40
62
60 1000 1050 1100
950
Temperature of quenching(A) 30 200 300 400 500 600
Remained 100 Temperature of tempering(A)
quenching
1183 1184
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
HEAT TREATMENT HEAT TREATMENT
-DC53- -SKS3CSKS93-
ISummary of quenching Standard time of heating Heat treatment SKS3
ISummary of ordinary quenching/tempering
¡Ordinary quenching Method Standard time of heating ISummary of hot bath quenching/tempering
Quenching 800~850A
1020~1040A Diameter/Thickness Immersed period Quenching 800~850A
800~850A Heating (mm) (minutes)
(Refer to the
right table.) 5 5~ 8
10 8~10
Salt bath 20 10~15
500AHot bath Preheating Oil cooling
Air cooling 600~650A
30 15~20 Preheating
600~650A
50 20~25
100 30~40
Air cooling or Oil cooling
Thickness Average temperature time
Electric furnace 100 or less 20~30min/25mm Hot bath
Gas furnace Over 100 20~30min./25mm thickness
10~20min./25mm thickness 40~50min/50mm 250A 150~200A
50~70min/75mm Air cooling
Air cooling
Air cooling
Box packed heating Average temperature time 30~45min./ Air cooling Tempering 150~200A 20~30min/25mm Tempering150~200A
Box thickness of 25mm
¡Vacuum quenching 40~50min/50mm
1020~1040A Put into the Put into the 50~70min/75mm
800~850A Standard time of heating furnace of 250A 60 minutes/25mm furnace of 250A 10min/25mm 60 minutes/25mm
Approx.100A
Heating Approx.100A
(Refer to the right table.)
Gas cooling Thickness Average temperature time Temperature of quenching Marquench
100mm
or less 20~30min. For objects of considerable thickness, select upper limit temperature. For thin objects or This method is suitable for the objects requiring precision finishing by
/25mm thickness
Over reducing hardening crack and strain, select lower limit temperature. avoiding deformation or bends, or objects with uneven thickness, many
100mm 10~20min.
/25mm thickness Maintaining quenching temperature time period holds, or remarkably complicated shapes.
1.Retention time in the left diagram is the standard for bare heating(electric IRelation between quenching ITempering hardness
funace and heavy oil furnace).
temperature and hardness curve
2.When the thickness is uneven, keep the exact heating time by partial heating or
covering the thin part. 67 Oil quenching 70
66
Hardness(HRC) Oil quenching
Hardness(HRC)
Talking out of oil 65 Temperature range 850A
64 of suitable quenching
ISummary of tempering IRelation between quenching temperature and hardness Approximately 250A is fine, but in the following cases, the 60
temperature can be raised. 63 800A
66 1.Due to remarkable uneven thickness, formation of cracks 825A
64 62
62 becomes easier. 750 775 800 825 850 875 900 925
60 2.When curved deformation easily occurs. Temperature of quenching(A)
3.When you wish to reform curve as soon as it is taken out.
1000 1020 1040 1060 1080 4.When surface hardness is not concerned. 50
Temperature of quenching(A/Air cooling)
Hardness(HRC)CLow temperature:180~200A
Hardness(HRC)CHigh temperature:500~550A
60~90 Air 40
min/25mm cooling
0 100 200 300 400 500 600
Temperature of tempering(A)
When the temperture is high, tempering is done twice. Heat treatment SKS93(For oil quenching)
ISummary of quenching ISummary of tempering
Temperature of quenching790~850A
Oil cooling 150~200A
Gradual heating 55600~0A Retention time Retention time Air cooling
(hours)
(minutes)
25(25mm) 2(25mm)
4(50mm)
50(50mm) Raising the temperature 5(75mm)
approx. 200A and then
70(75mm) to 100A.
ITempering hardness curve Approx. 1min./mm thickness When the tempering temperature is high, the retention time
should be kept at the rate of one hour per 25mm thickness.
64
62 Diagram of hardening for "no crack and hardening" ITempering hardness curve
60
58 Temperature of quenching 70
56 Critical SKS93(oil quenching at 820A)
54 550A
52 60
UTemperature Quenching Quenching
DC53 1040A Air cooling Hardness(HRC)rapidly50
DC53 1030A Air cooling
DC53 1020A Air cooling 250A 40
DC53 1040A Oil cooling
Critical gradually
Remained 200 300 400 500 520 540 560 580 zone
quenching Temperature of tempering(AM1hMTwice) 30
UTime
20
0 100 200 300 400 500 600
Temperature of tempering(A)
1185 1186
JIGS & FIXTURES SERIES FOR INSPECTION JIGS & FIXTURES SERIESPrice Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delive ryGTUimIDeE + 5 to 7 days · Please c%oRenferttoa"McecthanCicaul Stsandtaord CmompeonerntsSforeFacrtovryiAuctoema.tion Catalog for Toggle clamps.
JIGS & Limit gauges )Quality assurance certificate
FIXTURES SERIES
FOR INSPECTION PRECISION CARBIDE LIMIT GAUGES PRECISION CARBIDE LIMIT GAUGES LIMIT GAUGES PRECISION CARBIDE LIMIT GAUGES )Limit gauges
VGSA VGWA VGSB VGWB SGSA SGWA VGOA
Name It is standardized for inspection of precision press products and precision holes.
Catalog
No. 55 8C 8C 3A 3A 5 It is excellent in abrasion-resistance and dimension precision guaranteed for mass production.
Delivery 1189 1189 1190 1190 1191 1191 1192 )Guarantee of accuracy
Page
Each Limit gauge is measured during the machining, and re-measured after the machining in
a controlled temperature room at certain period of time for quality assurance purpose. Quality
assurance certificate with the actual measurement value of the outside diameter is attached to
each product. Traceability system table/measurement instruments table is not available .
PRECISION CARBIDE LIMIT GAUGES PLUG GAUGES FOR CHECKING FIXTURE )Measurement of gauges
VGOB
BGQ"BGQH"BGQT"BGQTH BGQEH"BGOEH BGO"BGOH BGU"BGUH BGOPH BGUPH Inspection item
8C
3 5 33 3 3 Measuring point Accuracy Method
1192 ABC
1193 1194 1195 1195 1196 1196 Comparison measurement with block gauge
by using measuring instruments.
Y Go end
2-
X 0
Outside diameter
Not-go end |1-
Y ABC AB
X
Circularity 1-or less
Cylindricality ABC AB 1-or less
Y
LOCATING PINS FOR CHECKING FIXTURE TAPER LOCATING PINS FOR CHECKING FIXTURE BUSHINGS FOR CHECKING FIXTURE Measuring through outside diameter.
BGTDSH"BGTA"BGTAH"BGTD"BGTDH BGMA BGMD JBA JBAM JBH JBHM KJBS KJBST KJBSK KJBSTK
X
3 33 1 3 3
Go end 6 points as A, B and C in two directions of X and Y.
1197 1198 1198 1199 1199 1200
Not-go end 4 points as A and B in two directions of X and Y.
Not-measured 1mm from the both ends of gauge.
)List of measuring instruments
Name of measuring instrument Manufacturer Model
BUSHINGS FOR CHECKING FIXTURE MARKING-OFF PINS FOR CHECKING FIXTURE LOCATING BARS FOR TAPPING POSITION SHIM PLATES FOR CHECKING FIXTURE Round type SHIM PLATES FOR CHECKING FIXTURE Square type Dimension ) Tool microscope Nikon MM 22
KJBSC KJBSTC BGK BGKS BGM ) All purpose end-measuring machine Carl Zeiss UHM
KGSPM KGSP ) Horizontal type end-measuring machine Kuroda Seiko SM 3
3 3 3 Tsugami UL 5D
11 ) Digital caliper Mitsutoyo CD series
1200 1201 1201 ) Micrometer Mitsutoyo MDC series
1202 1202 ) Pin gauge Aizen
) Block gauge Mitsutoyo EMC1.00O25.00
Code No.100.516 Set BM1 24SC 0/KM
Shape ) Roundness measuring device Tokyo Seimitsu
) All purpose measurement microscope Mashprivolintorque RONDCOM 45A
) Surface roughness measuring machine Mitsutoyo UIM21
Tokyo Seimitsu Surfcotest SV400
Surfcom 2B E-MD-S10A
SHIM PLATES FOR CHECKING FIXTURE Square type with hole
KGZ
1
1202
1187 1188
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
PRECISION CARBIDE LIMIT GAUGES PRECISION CARBIDE LIMIT GAUGES
-ONE END STEPPEDCBOTH ENDS STEPPED TYPE- -ONE END STEPPEDCBOTH ENDS STEPPED TYPE-
The volume discount rate is also applicable to alteration cost. P.39 The volume discount rate is also applicable to alteration cost. P.39
Quality assurance certificate is attached to these products. VGSA8C10 Quality assurance certificate is attached to these products.
VGSA1.6~6 H VGSB
6-120B
H H
6-120B
6-120B
+0.002 0.1 0.1 BC F S +0.002 6 B C3 F
0 L
S0 30B
2Gauge part
T Ú0.001 0.1 0.1LT Ú0.001 V20 0.1 d
S+0.003<T 88~89HRA 0.1
S+0.003<T +0.002 B CG F
H
6-120B S0
VGSA1.6 Side shape of knob part T Ú0.001 L
T-S¯1
1Knob part S+0.003<T 1Knob part 2Gauge part 3Neck part of gauge
Aluminum Aluminum V20 SKS3
Black alumite A clearance groove of about 1mm Black alumite 88~89HRA
VGWA8C10 is provided at the joint of B and C.
VGWA1.6~6 H VGWB
6-120B
H H H
6-120B 6-120B
H 6-120B
6-120B
0.1
30B
0.1
0.1
+0.002 5.5 +0.002 5.5 0.1
B 3 F 3 C T Ú0.001
S0 B FC T Ú0.001 S0 0.1 d 5d 0.1
L S+0.003<T
L S+0.003<T S +0.002 BG F GC T Ú0.001
0
L
VGWA1.6 Side shape of knob part
1Knob part 2Gauge part 1Knob part 2Gauge part 3Neck part of gauge
Aluminum V20 Aluminum V20 SKS3
Black alumite 88~89HRA Black alumite 88~89HRA
S+0.003<T
L H Catalog No. P(Applicable nominal value) SCT U/Price Q'ty:1~4 L Catalog No. P(Applicable nominal value) SCT U/Price Q'ty:1~4
BCF BCd F 0.001mm increments 0.001mm increments
Type No. 0.001mm increments 0.001mm increments VGSA VGWA GH Type No. VGSB VGWB
VGSA VGWA VGSB VGWB 10.000~ 14.000 9.901 ~ 14.100
40 40 3 2 35 6 12 14.001~ 18.000 13.901 ~ 18.100
48 48 5 3 5 1.6 0.300 ~ 1.600 0.300 ~ 1.700 20,000 23,100 86 92 12 8 7 60 8 14 14 18.001~ 24.000 17.901 ~ 24.100 22,300 20,900
12 17 18
50 50 6 4 40 2.0 1.601 ~ 2.000 1.501 ~ 2.100 18,500 20,800 104 112 9 VGSB 24 27,900 26,900
VGWB
57 57 2.5 2.001 ~ 2.500 1.901 ~ 2.600 16,500 108 120 16 10 12 70 31,900 31,200
3 2.501 ~ 3.000 2.401 ~ 3.100 16,800
67 67 8 VGSA 4 3.001 ~ 4.000 2.901 ~ 4.100 17,900 Tolerance marking P dimension(Applicable nominal value) Dimension of not-go end(T-P) Dimension of go end(S-P) Dimension of not-go end(T-P)
10 7 VGWA 5 4.001 ~ 5.000 3.901 ~ 5.100
50 The difference with P VGSB K S+0.003<T
dimension is engraved
70 73 6 5.001 ~ 6.000 4.901 ~ 6.100 16,900 instead of S and T values F 13.5 +0.010 -0.005 F13.5 +0.010 K P dimension is applicable
as shown. -0.005
Tolerance marking
The difference with P 10 8 6.001 ~ 8.000 5.901 ~ 8.100 17,200 18,100 P dimension(Applicable nominal value) nominal value(basic
dimension is engraved dimension measured).
instead of S and T values 10 8.001 ~ 10.000 7.901 ~ 10.100 17,500 18,600 Dimension of go end(S-P) VGWB
as shown.
P dimension(Applicable nominal value) Dimension of not-go end(T-P) Dimension of go end(S-P) Dimension of not-go end(T-P) K S+0.003<T Catalog No. P S T Catalog No. P S T (ACCMC)
VGSA Order Alteration VGSB 14 P13.500 S13.495 T13.510 AC-MC-S5011
F3.5 +0.010 +0.002 F3.5 +0.008 K P dimension is applicable VGSB 14 P13.500 S13.495 T13.510
+0.002 P dimension(Applicable nominal value) nominal value(basic
dimension measured).
Dimension of go end(S-P) VGWA 8Delivery Days Alterations Spec. \ 1Code
Code 2,000
VGSB VGWB
Catalog No. PST Catalog No. P S T (BCCCCCMC) Express C 1,000/1Pc. P.38 Air-vent F 2 is drilled into the
VGSA 4 P3.500 S3.502 T3.510 neck of gauge.
Order Alteration VGSA 4 P3.500 S3.502 T3.510 BC8-MC-S5011 A flat charge of 2,700 yen for 3 pieces or more of the same size. AC
IVolume discount rate P.37 Marked on the opposite side of tolerance marking.
5Delivery Days Alterations Code Spec. \ 1Code Price Quantity 1~4 5~9 10~19 20~50 Order code MC-S5011
VGSA VGWA 1,200 Rate - 5% 10% 15% <Working range>
1¯BC<B 0.1mm increments To be quoted on price & lead time above Max. Q'ty. S5011 S5011 MC CMaximum number of characters:12 characters 800
The full length L is shortened by(B-BC). (Numbers only ; 8 characters.)
IVolume discount rate P.37 B BC B BC BC
CPrintable:Alphabet, number,
Price Quantity 1~4 5~9 10~19 20~50 hyphen, slash, plus, asterisk, period
Rate - 5% 10% 15%
1¯CC<C 0.1mm increments
To be quoted on price & lead time above Max. Q'ty.
C CC CC C CC The full length L is shortened by(C-CC). 1,200
S5011 S5011 MC Marked on the opposite side of tolerance marking. 800
Order code MC-S5011
<Working range>
CMaximum number of characters:12 characters
(Numbers only ; 8 characters.)
CPrintable:Alphabet, number,
hyphen, slash, plus, asterisk, period
1189 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1190
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
LIMIT GAUGES PRECISION CARBIDE LIMIT GAUGES
-STANDARD ONE ENDCSTANDARD TWO ENDS TYPE-
Quality assurance certificate is attached to these products. The volume discount rate is also applicable to alteration cost. P.39 Quality assurance certificate is attached to these products. The volume discount rate is also applicable to alteration cost. P.39
SGSA3~13 SGSA16C20 VGOA1.6~6 VGOA8C10
H R0.5 or less 12 H H
6-120B 6-120B
6-120B
6-120B
+0.005 0.2 0.2 S+00.005 0.1 BF 6 B3 F
0.2 0.2 T Ú0.0025 L L
S0 BC F B C 10 F H +0.002 30B +0.002
T Ú0.0025 L
L P0 0.1P0
VGOA1.6 Side shape of knob part
S+0.007<T 1Knob part 2Gauge part 1Knob part 2Gauge part
A clearance groove of about 1mm is provided SS400 SKS3 Aluminum V20
at the joint of B and C. Fe3O4(Black oxide) 58HRC~ Black alumite 88~89H RA
SGWA3~13 SGWA16C20 Large diameter type VGOB
H H H H H
6-120BR0.5or less 6-120B 6-120B 6-120B 6-120B
R0.5or less
B 5.5 C B 10 5.5 10 C
F F
L L
0.2 0.1 d BG F
0.2 L
0.2 +0.002
+0.005 +0.005 0.2 P0
S0 T Ú0.0025 S0 TÚ0.0025
1Knob part 2Gauge part 1Knob part 2Gauge part 3Neck part of gauge
SS400 SKS3 Aluminum V20 SKS3
Fe3O4(Black oxide) 58HRC~ Black alumite 88~89HRA
S+0.007<T
L H Catalog No. SCT U/Price Q'ty:1~9 LB FH Catalog No. P U/Price
BCF 8 0.001mm increments 35 5 Type 0.001mm increments Q'ty:1~4
Type No. SGSA SGWA 38 3 40 No.
SGSA SGWA 1.000 ~ 3.000 45 5 VGOA 0.300 ~ 1.600 16,900
40 40 4 6 30 3 2.500 ~ 4.000 46 6 8 1.6 1.601 ~ 2.000 15,400
3.500 ~ 5.000 50 2.0 2.001 ~ 2.500 13,400
55 55 40 4 4.500 ~ 6.000 3,420 3,780 60 10 50 2.5 2.501 ~ 3.000
5.500 ~ 8.000 63 10 3 3.001 ~ 4.000 13,700
8 5 7.500 ~ 10.000 4 4.001 ~ 5.000
9.500 ~ 13.000 dFH 5 5.001 ~ 6.000 13,800
65 65 7 SGSA 6 12.500 ~ 16.000 3,570 4,070 7 60 12 6 6.001 ~ 8.000
67 67 10 10 SGWA 8 15.500 ~ 20.000 4,030 4,440 9 70 14 8 8.001 ~ 10.000 14,200
10 4,400 5,260 12 17 10 14,500
50 4,600 5,590 P
5,750 6,900 0.001mm increments U/Price
80 80 12 8 16 13 7,710 8,400 Q'ty:1~4
10.000 ~ 14.000
96 106 16 10 60 16 14.001 ~ 18.000 15,800
18.001 ~ 24.000 20,400
20 Catalog No. 23,700
Type
S+0.007<T L BG No.
VGOB
Catalog No. ST Catalog No. S T (MC) 78 12 6 14
SGSA 13 S10.450 T10.500 (Large diameter type) 18
Order Alteration SGSA 13 S10.450 T10.500 MC S5011 94 16 8 24
Delivery 3 Days
98 12
Alterations Code Spec. \ 1Code Catalog No. P Catalog No. P (ACCBCCMC)
SGSA SGWA VGOA 4 P3.500 BC8 MC S5011
Order VGOA 4 P3.500 Alteration VGOB 14 P13.500 AC MC S5011
Delivery VGOB 14 P13.500
Express A 800/1Pc. P.38 Marked on the opposite side of tolerance marking. KVGOA
Order code MC-S5011
A flat charge of 2,160 yen for 3 MC 1,000 5 Days Alterations Code Spec. \ 1Code
pieces or more of the same size. <Working range> 2,000
S5011 S5011 CMaximum number of characters:12 characters
(Numbers only ; 8 characters.)
IVolume discount rate P.37 CPrintable:Alphabet, Air-ventF 2 is drilled into the neck
number, hyphen, slash, plus,
Price Quantity 1~9 10~19 20~49 50~100 asterisk, period AC of gauge.
Rate - 5% 10% 15% Applicable only to the VGOB type.
To be quoted on price & lead time above Max. Q'ty. KVGOB Express C 1,000/1Pc. 1¯BC<B 0.1mm increments
8 Days P.38 B BC BC The full L is shortened by(B-BC). 1,200
S5011
A flat charge of 2,700 yen for 3 Applicable only to VGOA type.
pieces or more of the same size.
Marked on the opposite side of tolerance marking.
IVolume discount rate P.37 Order code MC-S5011
Price Quantity 1~4 5~9 10~19 10~201~9 50 MC <Working range> 800
CMaximum number of characters:12 characters
Rate - 5% 10% 10%15% (Numbers only ; 8 characters.)
CPrintable:Alphabet,
To be quoted on price & lead time above Max. Q'ty. number, hyphen, slash, plus,
asterisk, period
1191 1192
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
PLUG GAUGES FOR CHECKING FIXTURE P.39 PLUG GAUGES FOR CHECKING FIXTURE
-STRAIGHT TYPE- -OVAL TYPE-
The volume discount rate is also applicable to alteration cost. The volume discount rate is also applicable to alteration cost. P.39
BGQ BGQEH(Hardened type) F4 P.W Mark
BGQH(Hardened type)
R¯0.5
F4 FP Mark C0.2~1.0
G
0.8
G P -00.02
0.8
5 0 H 5 20 W-00.02
H 50 50
P -0.02 BGOEH(Hardened type) P>W
20 2Gauge part
SKD11
1Knob part 2Gauge part 1Knob part 60HRC~
SS400 SKS3 SS400
Fe3O4(Black oxide) Hardened type 40~45HRC Fe3O4(Black oxide)
BGQT (Tapered type) F4 P.W Mark R¯0.5 R¯0.5 S -1-00.02
BGQTH(Tapered/Hardened type) 2
H F4 FP Mark G G Detent
0.8 0.8
G
0.8 S h7
P-00.02
5 15B~30B 5 0 5 W-00.02
50 20 H 50 15 15
P -0.02
P>W>S
1Knob part 2Gauge part 1Knob part 2Gauge part
SS400 SKS3 SS400 SKD11
Fe3O4(Black oxide) Hardened type 40~45HRC Fe3O4(Black oxide) 60HRC~
Catalog No. P U/Price Q'ty:1~9 Catalog No. P Catalog No. 0.01mm increments U/Price
0.01mm increments BGQ 16 P12.00 Type Q'ty:1~9
Type H BGQ BGQH Order H P·Wmax. P·Wmin.
1.20 ~ 8.00 BGQEH 10 3,800
10 8.01 ~ 10.00 1,080 1,530 13 8.00 3.00 4,060
13 10.01 ~ 13.00 (Hardened type) 16 4,420
BGQ 16 13.01 ~ 17.00 1,170 1,660 3Delivery Days 21 10.00 6.00 5,220
BGQH 21
P 1,260 1,790 13.00 8.00
(Hardened type) 0.01mm increments
4.00 ~ 8.00 1,350 1,910 17.00 10.00
8.01 ~ 10.00
10.01 ~ 13.00 U/Price Q'ty:1~9 IVolume discount rate P.37
13.01 ~ 17.00
Catalog No. Price Quantity 1~9 10~19 20~49 50~100 Catalog No. 0.01mm increments S U/Price
Alteration Type 0.1mm increments Q'ty:1~9
Type H BGQT BGQTH Rate - 5% 10% 15% H P·Wmax. P·Wmin.
BGOEH 10 3.0 ~ 7.9 4,990
10 1,170 1,680 To be quoted on price & lead time above Max. Q'ty. 13 3.0 ~ 9.9 5,250
13 (Hardened type) 16 5.0 ~ 12.9 5,610
BGQT Catalog No. P (CHCMH) 21 8.00 4.00 9.0 ~ 16.9 6,410
26 9.0 ~ 20.9 7,130
(Tapered type) 1,260 1,800 BGQ 16 P12.00 CH 32 10.00 6.00 9.0 ~ 27.9 7,940
BGQTH 16 1,350 1,940 13.00 8.00
21
(Tapered/Hardened type) 1,440 2,060 \ 1Code
Alterations Code Spec. 17.00 10.00
M5 Sets the chain(length 21.00 16.00
10 CH 600mm)for preventing loss 500
Example 28.00 20.00
to the gauge main body.
Order Catalog No. P W S 5Delivery Days
Alteration
MH Adds tapped hol(e M5). 300 BGQEH 10 P86.050 W4.00 S3.0
BGOEH 10 P86.050 W4.50
(CHCMH) IVolume discount rate P.37
Catalog No. P WS CH
CH Price Quantity 1~9 10~19 20~49 50~100
BGQEH 10 P6.50 W4.00 Rate - 5% 10% 15%
Product BGOEH 10 P7.00 W4.00 S3.0
To be quoted on price & lead time above Max. Q'ty.
Main body of jig
Alterations Code Spec. \/1Code
Bushing for checking fixture
P.1199C1200 Sets the chain(length Example
CH 600mm)for preventing loss
500
to the gauge main body.
Product
M5 MH Adds tapped hol(e M5). 300 Bushing for checking fixture
10
P.1199C1200
Main body of jig
1193 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1194
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
PLUG GAUGES FOR CHECKING FIXTURE P.39 PLUG GAUGES FOR CHECKING FIXTURE P.39
-STEPPED/GAUGE LENGTH FIXED TYPE- -STEPPED/GAUGE LENGTH SPECIFIED TYPE-
The volume discount rate is also applicable to alteration cost. The volume discount rate is also applicable to alteration cost.
BGO BGOPH
BGOH(Hardened type)
F4 FP Mark C0.5 C0.5 F4 FP Mark C0.5 C0.5
G G G G
0.8 0.8 0.8 0.8
H 5 15 15 S h7 P>S H 5 BA S h7 S<P
50 50
Undercut of about 1mm is 0 Undercut of about 1mm is 0
provided at the joint of steps. 1Knob part provided at the joint of steps.
SS400 P-0.02 P-0.02
BGU Fe3O4(Black oxide) BGUPH
BGUH(Hardened type) 2Gauge part 1Knob part 2Gauge part
SKS3 SS400 SKS3
Fe3O4(Black oxide) 40~45HRC
(Hardened type)40~45HRC
F4 FP Mark C0.5 C0.5 F4 FP Mark C0.5 C0.5
G G G G
0.8 0.8 0.8 0.8
5 15 15 0 P<S 5 BA 0 S>P
H 50 H 50
P-0.02 P-0.02
S h7 S h7
Undercut of about 1mm is 1Knob part 2Gauge part Undercut of about 1mm is 1Knob part 2Gauge part
provided at the joint of steps. SS400 SKS3 provided at the joint of steps. SS400 SKS3
Fe3O4(Black oxide) (Hardened type)40~45HRC Fe3O4(Black oxide) 40~45HRC
Catalog No. P 0.01mm increments S 1mm increments U/Price Q'ty:1~9 S Catalog No. P 0.01mm increments A B U/Price Q'ty:1~9
BGO BGOH BGU BGUH BGOPH BGUPH Type 1mm increments 1mm increments BGOPH BGUPH
Type H BGOCBGOH BGUCBGUH BGOCBGOH BGUCBGUH 1,260 1,730 1,260 1,730 H BGOPH BGUPH
1,350 1,860 1,350 1,860 48 BGOPH 10 5 ~ 15 5 ~ 15 2,180 2,180
BGO 10 4.00 ~ 8.00 4.00 ~ 7.00 3~ 7 5~ 8 1,440 1,980 1,440 1,980 6 10 BGUPH 13 4.01~ 8.00 4.00 ~ 7.00 2,420 2,420
BGOH 13 8.01 ~ 10.00 7.01 ~ 9.00 1,530 2,120 1,530 2,120 8 13 16 8 ~ 20 8 ~ 20 2,580 2,580
16 10.01 ~ 13.00 9.01 ~ 12.00 6~ 9 8 ~ 10 1,620 2,260 1,620 2,260 BGOPH:S<P BGUPH:S>P 8.01~ 10.00 7.01 ~ 9.00
(Hardened type) 1,710 2,400 1,710 2,400
8 ~ 12 10 ~ 13 10.01~ 13.00 9.01 ~12.00
BGU 21 13.01 ~ 17.00 12.01 ~ 15.00 10 ~ 15 14 ~ 17
BGUH 26 17.01 ~ 21.00 15.01 ~ 17.00
32 21.01 ~ 28.00 17.01 ~ 24.00 10 ~ 17 18 ~ 21 Catalog No. P A B Catalog No. P A B (CHCMH)
(Hardened type) BGOPH 16 P10.05 A15 B20 A15 B20 CH
10 ~ 24 21 ~ 28 Order Alteration BGOPH 16 P10.05
BGOCBGOH:P>S BGUCBGUH:P<S
Catalog No. P S IVolume discount rate P.37 To be quoted on 3Delivery Days Alterations Code Spec. \/1Code
BGO 16 P12.00 S10 price & lead time
Order Price Quantity 1~9 10~19 20~49 50~100 above Max. Q'ty. M5 Sets the chain(length 600mm)
10 CH for preventing loss to the gauge
Rate - 5% 10% 15% 500
main body.
IVolume discount rate P.37
3Delivery Days Example Price Quantity 1~9 10~19 20~49 50~100
Rate - 5% 10% 15%
BGO
BGOH To be quoted on price & lead time above Max. Q'ty. MH Adds tapped hol(e M5). 300
Alteration Catalog No. P S(SCH) (CHCMH) Product Example
Alterations
BGO 16 P12.00 S10 CH Main body of jig
BGU 21 P13.01 SCH12.55 MH
Bushing for checking fixture
Code Spec. \/1Code P.1199C1200 BGOPH
Sets the chain(length 600mm) 500 BGU BGUPH
CH for preventing loss to the gauge BGUH
Product
main body. Main body of jig
Product
M5 MH Adds tapped hole(M5). 300 Main body of jig Main body of jig
10 Product
Bushing for checking fixture
BGOi BGUi S dimension unit change P.1199C1200
0.01mm increments
SCH SCH 300
SCH The applicable range is as same
as the standard table.
1195 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1196
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
LOCATING PINS FOR CHECKING FIXTURE TAPER LOCATING PINS FOR CHECKING FIXTURE
The volume discount rate is also applicable to alteration cost. P.39 -WITH SCREW TYPE- P.39
The volume discount rate is also applicable to alteration cost.
BGTDSH(Hardened type) F4 FP Mark BGMA(Round/Hardened type)
G G C0.5 E
0.8 0.8
F4 FP Mark Taper 1 5 M
G G
0.8 0.8
5 S h7 60B P
H 50 FS h7
0 2Gauge part P-1.0 Ú0.2
SKS3 P+1.0 Ú0.2
P-0.02 40~45HRC
10 B
{ }S< S<P-1 5 52
3 E+ P2-E2 1Knob part H 50 10 12 12
2 3 SS400 2Gauge part
Fe3O4(Black oxide) SKS3 Undercut of about 1mm is 1Knob part
Undercut of about 1mm is provided at the joint of steps. 40~45HRC(Hardened type) provided at the joint of steps. SS400
Fe3O(4 Black oxide)
BGTA (Round type) F4 FP Mark Taper 1 E BGMD(Diamond/Hardened type) 2Gauge part
BGTAH(Round/Hardened type) 0.8 G 5 SKS3
40~45HRC
PG
S h70.8 M
P-1.0Ú0.2
P+1.0Ú0.2 F4 FP Mark
5 5
H 50 10 B G
0.8
Undercut of about 1mm is 1Knob part S
provided at the joint of steps. SS400 P 2
Fe3O4(Black oxide) 12
BGTD (Diamond type) FS h7
BGTDH(Diamond/Hardened type) P-1.0 Ú0.2E
P+1.0 Ú0.2
5 5
H 50 10 10 12
F4 FP Mark Taper 1
0.8 G 5
P G 1Knob part 2Gauge part
S h70.8 SS400 SKS3
P-1.0Ú0.2 Fe3O(4 Black oxide) 40~45HRC
P+1.0Ú0.2
5 5 60B Undercut of about 1mm is provided at the joint of steps. 60B
H 50 10 B
2Gauge part
{ }S< 1Knob part SKS3 S E MMP Catalog No. P U/Price Q'ty:1~9
3 E+(P-13)2-E2 SS400 40~45HRC(Hardened type) (BGMD only) Type H 0.01mm increments
2 Fe3O4(Black oxide) 13 7.20 ~ 9.00 BGMA BGMD
16 9.01 ~ 12.00
Undercut of about 1mm is provided at the joint of steps. 6 3 5 M 0.8 21 12.01 ~ 16.00 2,780 5,560
26 16.01 ~ 20.00
Catalog No. P S U/Price 8 4 6 M 1.0 32 20.01 ~ 27.00 3,010 6,170
Type 0.01mm increments 0.1mm increments Q'ty:1~9
BE H BGMA(Round/Hardened type) 3,160 6,770
BGTDSH 13 6.00~ 9.00 3.0~ 6.0 2,780 6 BGMD(Diamond/Hardened type)
15 3 16 9.01~ 12.00 5.0~ 8.0 2,930 3,610 7,520
17 4 (Hardened type) 21 12.01~ 16.00 9.0~12.0 3,210 10 8 8 M 1.25
19 6 26 16.01~ 20.00 9.0~15.0 3,510
24 8 32 20.01~ 27.00 9.0~20.0 4,180 10 3,910 8,270
30 10
H P S U/Price Q'ty:1~9 Catalog No. P IVolume discount rate P.37 To be quoted on
13 0.01mm increments 1mm increments BGTA BGTAH BGTD BGTDH BGMD 16 P10.00 price & lead time
16 1,530 2,150 1,800 2,850 Order Price Quantity 1~9 10~19 20~49 50~100 above Max. Q'ty.
21 6.00~ 9.00 3~ 6 1,800 2,270 1,890 3,010 Alteration
E Catalog No. 26 9.01~ 12.00 5~ 8 1,800 2,400 2,070 3,300 Rate - 5% 10% 15%
Type 32 12.01~ 16.00 9 ~ 12 1,890 2,670 2,340 3,610
( )B BGTD/BGTDH 16.01~ 20.00 9 ~ 15 2,160 3,160 2,700 4,280 Catalog No. P (CHTCMH)
only 20.01~ 27.00 9 ~ 20 BGMD 13 P8.00 CHT
15 3 BGTA (Round type) 3Delivery Days
17 4
19 6 BGTAH(Round/Hardened type) Alterations Code Spec. \/1Code
24 8 BGTD (Diamond type)
30 10 BGTDH(Diamond/Hardened type) Sets the chain(length 600mm)for
IVolume discount rate P.37 CHT preventing loss to the gauge main 500
body.(With anti-twisting)
Catalog No. P S
Order Price Quantity 1~9 10~19 20~49 50~100
BGTDSH 16 P10.00 S5.0 Alteration Rate - 5%
BGTD 16 P12.00 S5 10% 15% M5
10
To be quoted on price & lead time above Max. Q'ty. Example BGMA BGMD MH Adds tapped hole(M5). 300
Catalog No. P S (CHCMH)
3Delivery Days BGTDSH 16 P12.00 S6.0 CH
BGTA 16 P12.00 S5 CH
Alterations Code Spec. \/1Code IBGMD Structure:Diamond part rotates.
Example Sets the chain(length 600mm)
CH for preventing loss to the gauge
Product M5 500 GDiamond part rotates.
10 main body. 300 Bushing for checking fixture
Main body
of jig MH Adds tapped hol(e M5). P.1199C1200
Bushing for checking fixture
P.1199C1200
1197 Express P.38 http://misumi.jp/press/ For inquiry, ordering and 1198
service system other information, refer to
Press 2007 P.1269
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
BUSHING FOR CHECKING FIXTURE
Round/Fixed type JBA (p6) JBH (p6/flanged type) G Segment type KJBSK KJBSTK(Flanged type) 6.3 1.6
JBAM(m6) JBHM(m6/flanged type) 25 6.3 0.4
A C0.5 1.0 A
A C0.5 1.5 G A 1.6
1.6
G 1.5 0.4
0.4 10B 10B P++00..0031
D-00.02
H Ú0.05
0
D -0.2
P++00..0031
D-00.02
d G6 G F4H7 1.6 F4H7 1.6
D 0.4 F+00.05 F+00.05
R G HR L-00 .5
0.4
6.3 F0.02 A TÚ0.05
L-00.5
d G6
D F0.02 A
T L 0 F0.01 A
L 0 F0.01 A –0.5
-0.5 SKS3
L dimension of flanged type does 60HRC~
not include flange thickness. SKS93 50~60HRC
RHTD D tolerance Catalog No. L U/Price Q'ty:1~29 H Catalog No. P F L T U/Price Q'ty:1~4 Order Catalog No. P F L T
p6 m6 G6 JBACJBAM JBHCJBHM T3
Type d Type D 0.01mm increments 0.1mm increments 1mm increments Selection KJBSK KJBSTK KJBSK12 P8.00 F2.0 L10
KJBSTK12 P8.00 F3.0 L10
9 5 +0.020 +0.012 2 +0.008 880 1,330 8 3.00~ 5.00 0.3~ 3.0 5~20 2,000 2,200
0.8 2.5 +0.012 +0.004 +0.002 5 6 8 10 12 790 1,150 10 3.00~ 7.00 0.3~ 3.0 when P¯3.59 2,000 2,200
12 3.00~ 9.00 0.5~ 4.0 2,200 2,400
11 7 3 D+4 KJBSK 16 4.00~13.00 0.5~ 6.0 L¯PM2.5 2 2,700 2,900 3Delivery Days
KJBSTK 20 6.00~17.00 1.0~ 8.0 when P˘3.60 3 3,200 3,400
12 8 +0.024 +0.015 JBA (p6) 4 +0.012 5 6 8 10 12 15 16 20 700 970 5
JBAM (m6) 5 +0.004 610 880 KJBSK:D/2-F˘3
1.0 14 3 +0.015 +0.006 6 570 880 IVolume discount rate P.37
10 5 6 8 10 12 15 16 20 25 570 880
+0.014 610 970 25 8.00~21.00 2.0~10.0 L¯PM3 3,500 3,700 Price Quantity 1~4 5~19 20~49 50~99
+0.005 6 8 10 12 15 16 20 25 Rate - 5% 10% 15%
16 12 +0.029 +0.018 8 To be quoted on price & lead time above Max. Q'ty.
+0.018 +0.007
19 4 15 (Head type) 10 Catalog No. P F L T (FCCPKCCNCCTKC)
12
22 18 JBH (p6) 13 8 10 12 15 16 20 25 30 700 970 Alteration KJBSK12 P8.00 F2.0 L10 FC
JBHM (m6) 15
2.0 26 22 +0.017 10 12 15 16 20 25 30 790 1,230
+0.006 880 1,410
5 25 +0.035 +0.021 Alterations Code Spec. \/1Code Alterations Code Spec. \/1Code
26 +0.022 +0.008 200 NC 300
30 16 12 15 16 20 25 30 880 1,410 5D-1 32 Adds loose prevention
200 TKC groove. 400
35 30 20 +0.020 970 1,590 Adds adhesive pool TKC D-1
3.0 40 6 +0.007 1,050 1,760 FC groove. D˘P+3
Change flange thickness
35 +0.042 +0.025 25 16 20 25 30 35 tolerance to Ú0.01.
+0.026 +0.009
PKC Applicable only to KJBSTK.
Change P dimension
Catalog No. L 1 Day JBA IVolume discount rate P.37 PKC tolerance to H7.
Quantity 1~29 30~49 50~99
JBA 10 16 JBAM Rate 10% 100~199
JBH 8 12 - 5% 15%
JBH IVolume discount rate P.37
Quantity 1~29 30~49 50~79
- 5% 10% 80~99 Oval type KJBSC KJBSTC(Flanged type) C0.5 1.0 6.3 1.6
JBHM Rate 15%
+0.03 1.6
To be quoted on price & lead time above Max. Q'ty.
W +0.01 1.6
Round/Specified type KJBS KJBST(Flanged type) 6.3 1.6 F4H7 1.6 F4H7
R
A C0.5 1.0 A +0.03 1.6 D-00.02 +0.03 H Ú0.05
1.6 +0.01 D-00.2
1.6 P+0.01 L-00.5 D-00.02R
P
R P++00..0013
D-00.02
1.6 HÚ0.05
L-00 .5 0
F0.02 A D -0.2
P++00..0013
D-00.02
R 1.6 +0.03 TÚ0.05
TÚ0.05
W+0.01 L-00.5
L-00.5 SKS93 50~60HRC
F0.02 A
SKS93 50~60HRC RH Catalog No. P W L T U/Price Q'ty:1~4 Order Catalog No. P W L T
T2
Type D 0.01mm increments 0.01mm increments 1mm increments Selection KJBSC KJBSTC KJBSC12 P8.50 W3.50 L15
KJBSTC12 P9.50 W4.50 L15
Catalog No. U/Price Q'ty:1~4 (8) 4.00~ 6.00 - 4,800
PL T KJBS KJBST 4,500 4,800
RH Type D 0.01mm increments 1mm increments Selection Order Catalog No. P L T 10 4.00~ 8.00 5~20 2 4,800 5,030 3Delivery Days
950 1,100 T2 12 3 5,600 5,800
1.0 8 2.00~ 6.00 2 950 1,100 KJBS10 P3.00 L6 2.0 D+4 KJBSC 16 4.00~10.00 P>W (L¯PM2.5) 5 6,500 6,900
2.00~ 8.00 3 980 1,150 KJBST10 P3.00 L6 KJBSTC 20 8,100 8,500
D+4 4.00~10.00 5~40 5 1,060 1,340 25 8.00~14.00(W˘3.00) 15~20 IVolume discount rate P.37
2.0 10 8.00~14.00 1,210 1,630
10.00~18.00 when P¯3.59 1,350 1,820 3Delivery Days 10.00~18.00 Price Quantity 1~4 5~19 20~49 50~99
KJBS 12 15.00~23.00 L¯PM2.5 15.00~22.00 (KJBSTC only) Rate - 5% 10% 15%
Alterations
KJBST 16 when P˘3.60 IVolume discount rate P.37 R is 0.5 when(D-P)/2¯2. ({ D-W)/2 }-2˘1(KJBSC only) D8 is the standard only for KJBSTC. To be quoted on price & lead time above Max. Q'ty.
L¯PM3
20 Price Quantity 1~4 5~19 20~49 50~99 Catalog No. P W L T (FCCPKCCNCEetc.)
Rate - 5% 10% 15%
25
To be quoted on price & lead time above Max. Q'ty. Alteration KJBSC12 P8.00 W3.00 L15 FC
R is 0.5 when(D-P)/2¯2.
Catalog No. P L T (FCCPKCCNCEetc.) Code Spec. \/1Code
KJBS10 P3.00 L6 FC
Alteration PKC Alterations Code Spec. \/1Code Alterations Code Spec. \/1Code
200 400
PKC Change P dimension 200 5D-1 Adds adhesive pool groove. 200 TKC Change flange thickness
tolerance to H7. 300 RN TKC tolerance to Ú0.01.
Alterations Code Spec. \/1Code 32 FC D˘P+3
FC Adds adhesive pool 200 L˘15 Applicable only to KJBSTC
5 groove. (Only L=20 for KJBSTC)
32D-1 NC 300 Change flange thickness
D˘P+3 TKC tolerance to Ú0.01. 400 PKC
Adds loose prevention
groove. TKC Applicable only to KJBST. PKC Change P dimension RN R is C-chamfered -100
tolerance to H7. (less than 0.5).
D˘P+3
D-1 R is C-chamfered 0 D-1 Adds loose prevention
RN (less than 0.5). NC groove.
RN
D˘P+3
1199 1200
Price Indication: EUR = YEN / 100 · Delivery Time Indication: Catalogue Delivery Time + 5 to 7 days · Please contact Customer Service.
MARKING-OFF PINS FOR CHECKING FIXTURE/LOCATING BARS FOR TAPPING POSITION SHIM PLATES FOR CHECKING FIXTURE ZERO PLATE
ROUND"SQUARE"SQUARE WITH HOLE TYPE
Marking pins BGK The volume discount rate is also applicable to alteration cost. P.39 KGSPM Round type 1.5
BGKS (P dimension specified type)
3 K! 90!
2.5
$Ph7
$Ph7
55 SS400
Fe3O4 Black oxide
H 50 B 50 B Cross-recessed countersunk screw 1Pc.
M2+15
A T|0.02
1.5
Knob part Gauge part KGSP Square type B
SS400 SKS3
Fe3O4 (Black oxide) 58HRCO 4.5
Catalog No. P B U/Price Catalog No. P B K! U/Price A 90!
1mm increments Q'ty 1O9 A 2.5
Type Type H 0.1mm increments 1mm increments Selection Q'ty 1O9 4.5
H
2,870
16 10 1,750 16 6.0O14.0 10 3,160
16 1,880 21 14.1O18.0 20 3,440
BGK 21 20 20 O 50 2,000 (P dimBensioGn spKecifieSd type) 26 18.1O20.0 20 O 50 30 4,070
26 25 2,170 32 20.1O25.0
32
Catalog No. P B K! 3Delivery 4.5
Order BGK 16 P10 B30 Days B 4.5 T|0.02
Alteration BGKS 21 P16.0 B40 K20 2
'Volume discount rate P.37 SS400
Cross-recessed countersunk screw 2Pcs.
Catalog No. P B K! (CH"MH) %When A"B 15 Fe3O4 Black oxide M2+15
BGKS 16 P10.0 B30 K10 CH Price Quantity 1O9 10O19 20O49 50O100 When A"B 15 1Pc.
KGZ Square type with hole A
Rate 5 10 15 M 2 countersunk hole 1.5
4.5
To be quoted on price & lead time above Max. Q'ty.
Alterations Code Spec. /1Code Example 4.5
500 90!
M5 Sets the chain(length 300 Main body of jig A
10 Product 4.5 d 2.5
CH 600mm)for preventing loss
to the gauge main body.
MH Adds tapped hol e M5 .
Location bars for BGM Bushing for checking fixture SS400
tapping position P.1199"1200 Fe3O4 Black oxide
0.8 4.5 T|0.02
M
0.01
0
D Catalog
No. U/Price Catalog
No. B T
Q'ty 1O29 20
3.2 0.8 Type A T
Order KGSPM20 3
2"3"5 140
Delivery KGSP15 3
L 15 SKS3 KGSPM 20 KGZ25 5
Alignment of the screw part to the shank is under 0.1. 55O60HRC U/Price
Q'ty 1O29 1 Day
U/Price Catalog
No. B T
D M+P Catalog No. M L Q'ty 1O9 Type A 180 'Volume discount rate P.37
8 Type 3 10 20 30 10 20 2 190
14 3 + 0.5 4 3,010 15 3 200
Price Quantity 1O29 30O49 50O99 100O200
Order 4 + 0.7 BGM 5 3,170 5 210
5 + 0.8 6 3,510 20 220 Rate 5 10 15
6 + 1.0 8 3,840 25 T 230
8 + 1.25 10 4,180 15 20 2 240 To be quoted on price & lead time above Max. Q'ty.
10 + 1.5 12 4,510 20 25 3
12 + 1.75 4,680 KGSP 5 U/Price
Example
Example Q'ty 1O29
Work
250
Catalog No. L 280 Toggle clamp
BGM 4 L20 310
25 25
Only one countersunk hole for 15-15 available.
3Delivery Days d Catalog
No. KGZ
Main body of jig
Type A
Bushing for checking fixture
'Volume discount rate P.37 8 20
P.1199"1200
Price Quantity 1O9 10O19 20O49 50O100 To be quoted on price & 12 KGZ 25
Rate 5 10 15 lead time above Max. Q'ty. KGSPM"KGSP
%Make sure that nut and barring screw are vertical against the surface. 18 30
1201 1202
The words you are searching are inside this book. To get more targeted content, please make full-text search by clicking here.
Press_Dies_English_Issue2007
Discover the best professional documents and content resources in AnyFlip Document Base.
Search
Press_Dies_English_Issue2007
- 1 - 50
- 51 - 100
- 101 - 150
- 151 - 200
- 201 - 250
- 251 - 300
- 301 - 350
- 351 - 400
- 401 - 450
- 451 - 500
- 501 - 550
- 551 - 600
- 601 - 650
- 651 - 663
Pages: