PARTS LIST INSTALLATION - HandA-Accessories.com

INSTALLATION Accessory Application Publications No.
INSTRUCTIONS
TWEETER KIT CR-V AII 27197
PARTS LIST P/N 08A55-S9A-100
2 Tweeters Issue Date

Right tweeter harness SEP 2004
(marked “AS”)
INSTALLATION

Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for the
radio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

3. Remove the passenger’s dashboard under cover
(release the three clips and two pins).

CLIP (3)

Left tweeter harness
(marked “DR”)

8 Wire ties PASSENGER’S
DASHBOARD
PIN (2) UNDER COVER

TOOLS AND SUPPLIES REQUIRED AII 27197 (0409) 08A55-S9A-1000-91 1 of 7
Phillips screwdriver
Flat-tip screwdriver
Small flat-tip screwdriver
Piece of wire
Electrical tape
Masking tape

© 2004 American Honda Motor Co., Inc - All Rights Reserved.

4. Open the glove box. Release the right and left 7. Apply masking tape to the left front pillar and the
stops. dashboard along the edges of the tweeter cover.
Release the retaining clips with a small flat-tip
TAB (2) STOP (2) screwdriver wrapped with a shop towel. Pry up on
the tweeter cover to remove it. Take care not to
damage the clip and retaining tabs.

TABS

TWEETER
COVER

RETAINING
CLIP

GLOVE
BOX

SCREWS DASHBOARD

5. Remove the two screws from the bottom of the 8. Remove the tweeter cover from the right side of
glove box, and remove the glove box. the vehicle using the above procedure.

6. Remove the driver’s dashboard under cover (turn
the knob 90° clockwise, and release the retaining
clip).

HOLDER

RETAINING KNOB
CLIP Turn clockwise 90°.

DRIVER’S
DASHBOARD
UNDER COVER

2 of 7 AII 27197 (0409) © 2004 American Honda Motor Co., Inc - All Rights Reserved.

8. Remove the left kick panel (pull to release the two Routing the Left Tweeter Harness
clips). 10. While wearing gloves, locate and unplug the

TAB vehicle 13-pin connector (white) under the
dashboard on the driver’s side of the vehicle.

BODY FRAME

CLIPS

TAB
LEFT KICK
PANEL

VEHICLE 13-PIN
CONNECTORS

9. Remove the right kick panel (pull to release the 12. Get the left tweeter harness from the kit. Route a
two clips). piece of wire down from the tweeter cover
opening to the floor, and tape the 2-pin connector
RIGHT KICK to the wire.
PANEL
TAB

PIECE OF WIRE

TWEETER COVER
OPENING

CLIPS TAB

Use tweeter STEERING DUCT
harness HANGER
marked “DR.” BEAM

PIECE TWEETER HARNESS
OF WIRE 2-PIN CONNECTOR

© 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27197 (0409) Tape the 2-pin
connector to the wire.

3 of 7

13. Pull the left tweeter harness 2-pin connector up 16. Get one tweeter from the kit. Install the tweeter on
from the floor to the tweeter cover opening. the back of the tweeter cover by engaging the
three tabs with the square holes in the tweeter
TWEETER cover.
COVER
OPENING TWEETER

Route behind TABS (3)
the duct.
LEFT
TWEETER
COVER

STEERING DUCT
HANGER PIPE

13-PIN LEFT TWEETER Engage the tabs of
CONNECTORS HARNESS the tweeter with the
square holes in the
14. Remove the wire from the 2-pin connector. To tweeter cover.
prevent the tweeter harness from falling, tape it to
the dashboard. 17. Plug the left tweeter harness 2-pin connector into
the tweeter 2-pin connector, then reinstall the
15. Plug the two left tweeter harness 13-pin tweeter cover.
connectors into the vehicle 13-pin connectors that
you unplugged in step 11. TWEETER
COVER
VEHICLE 13-PIN
CONNECTORS TWEETER
2-PIN
CONNECTOR

DASHBOARD

TWEETER HARNESS
2-PIN CONNECTOR

4 of 7 LEFT TWEETER © 2004 American Honda Motor Co., Inc - All Rights Reserved.
HARNESS
13-PIN CONNECTORS

AII 27197 (0409)

18. Slide the left tweeter harness 13-pin connector into Routing the RightTweeter Harness
the vehicle connector clip. Make a loop in the left
tweeter harness, and secure it to the vehicle 19. Inside the glove box opening, locate and unplug
harness with three wire ties in the areas shown. the vehicle 13-pin connector (white) under the
dashboard.

Loop the
harness
in this area.

VEHICLE
HARNESS

WIRE TIES

BODY FRAME

LEFT VEHICLE 13-PIN
TWEETER CONNECTOR
HARNESS (White)

LEFT TWEETER 20. Get the right tweeter harness from the kit. Route
HARNESS a piece of wire down from the tweeter cover
13-PIN CONNECTOR opening to the floor, and tape the 2-pin connector
to the wire.

TWEETER COVER PIECE OF WIRE
OPENING

Route behind
the duct.

VEHICLE Use the
CONNECTOR CLIP tweeter harness
marked “AS.”
PIECE OF WIRE
TWEETER
© 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27197 (0409) HARNESS
2-PIN
CONNECTOR

Tape the 2-pin
connector to the wire.

5 of 7

21. Pull the right tweeter 2-pin connector up from the 23. Plug the two right tweeter harness 13-pin
floor to the tweeter cover opening. connectors into the vehicle 13-pin connectors you
unplugged in step 19.
TWEETER
COVER
OPENING

DUCT

STEERING
HANGER
BEAM

VEHICLE 13-PIN
CONNECTORS

RIGHT RIGHT TWEETER
TWEETER HARNESS
HARNESS 13-PIN CONNECTORS

13-PIN 24. Get the other tweeter from the kit. Install the
CONNECTORS tweeter on the back of the tweeter cover by
engaging the three tabs with the square holes in
22. Remove the wire from the 2-pin connector. To the tweeter cover.
prevent the tweeter harness from falling, tape it to
the dashboard. TWEETER

TABS (3)

RIGHT
TWEETER
COVER

Engage the tabs of
the tweeter with the
square holes in the
tweeter cover.

6 of 7 AII 27197 (0409) © 2004 American Honda Motor Co., Inc - All Rights Reserved.

25. Plug the right tweeter harness 2-pin connector into 27. Reconnect the negative cable to the battery.
the 2-pin connector of the tweeter, then reinstall
the tweeter cover. 28. Enter the radio anti-theft code, and reset the
customer’s radio station presets.
TWEETER
COVER 29. Reset the clock.

DASHBOARD 30. Reinstall all removed parts.

TWEETER HARNESS TWEETER 2-PIN NOTE: Whenever the battery is disconnected, the
2-PIN CONNECTOR CONNECTOR driver’s window AUTO function is disabled.

26. Slide the right tweeter harness 13-pin connector 31. Start the engine. Push down on the driver’s
into the vehicle connector clip. Make loops in the window switch until the window is fully open.
right tweeter harness, and secure it to the vehicle
harness with three wire ties in the area shown. 32. Pull up on the driver’s window switch to close the
window completely, then hold the switch for
Loop the excess 2 seconds or more.
harness in this area.
33. Test the AUTO window function.

34. Do the ECM/PCM idle learn procedure.

– Make sure all electrical items are turned off.

– Start the engine. Hold the engine speed at
3,000 rpm with no load (in Park or Neutral)
until the radiator fan comes on.

– Let the engine idle for about 5 minutes with the
throttle fully closed and with all electrical items
off.

NOTE: If the radiator fan comes on during this
step, the time it operates must not be
included in the 5 minutes.

VEHICLE WIRE
HARNESS TIES

RIGHT
TWEETER
HARNESS

RIGHT TWEETER VEHICLE
HARNESS CONNECTOR
13-PIN CONNECTOR CLIP

© 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27197 (0409) 7 of 7