Engineering Technical Drawing Exam Questions for SS1-3

https://stcharlesedu.com FIRST TERM EXAMINATION
SUBJECT: TECHNICAL DRAWING CLASS: SS1 Time: 1½ HRS
Instruction: Answer all questions in section A and THREE in B.

SECTION A
(Objective Test: Choose the option from a – d)

1. Freehand sketching involves the use of eraser ... and......... (a) Pencil, paper (b)Pencil,
Scale (c)Protractor ,divider (d)Sharpener, compass

2. All these are sizes of a drawing board EXPECT...........(a) A4 = 210mm * 297mm (b) A2
= 470mm * 650mm (c) A2 = 450mm * 650mm (d) A0 = 840mm * 1189mm

3. ……….. is drawn at the bottom right hand corner of the drawing paper (a)
Information (b) Title block (c) Lettering (d) dimensions

4. …………. are used to draw vertical lines by placing one side of the triangle containing
the right angle against the upper edge of the T-square (a) Drawing board (b)Set
square (c) Tee square (d) Drawing paper

5. ........... is used to draw arcs and circles (a) Pair of compass (b)Set square (c) Tee
square (d) Drawing paper

6. The diagram above shows (a) A perpendicular line (b) Angle 60 (c) parallel line (d)
Vertical line

7. An acute angle is one which is less than…………(a) 600 (b)900 (c) 450 (d)350

8. The above diagram is ………….(a) Concentric circles (b)Eccentric circle (c) normal (d)
Tangent

9. …………. are plane figures bounded by four straight lines (a) Eccentric circle (b) Circle
(c) Quadrilaterals (d) Tangent

10. All these are the properties of a quadrilaterals EXPECT (a) They have equal vertex (b)
It has all four sides equal (c) all its angles are right angles (d) the diagonals are equal
and they bisect each other at the centre forming angle 900

11. ……… is the process of putting down information on a drawing by means of letters,
words and numbers (a) Information (b) Title block (c) Lettering (d) dimensions

12. ………….. are used for angular measurements. a) Pair of compass (b)Set square (c)
Tee square (d) Protractors

13. Which of the following instrument is used to transfer measurement from one point to
another(a) A pair of compasses (b) A pair of divider (c) Protractor (d) Set square

14. A straight line is the shortest distance between …….. points (a) 3(b) 6 (c) 4 (d) 2
15. In the figure below, line AO is …….. to BC (a)Adjacent (b) perpendicular (c) Opposite

(d) Parallel
A
https://stcharlesedu.com
BO C

16. We use ……… for setting paper on the drawing board (a) Pencil (b) Tee square (c) Set
square (d) Compass

17. The drawing instrument used for measuring angles is ………. (a) Compass (b) ruler
(c) Protractor (d) Set square

18. These are importance of technical drawing EXCEPT (a) It develop our skill (b) It help
to interpret drawing (c)Means of communication (d) It gives us information about
events

19. Pencil for lettering should be sharpen to……… point(a) double (b)Curve (c) Conical
(d)fine

20. Drawing materials and instrument should be ……….. (a) Handle with care (b)Handle
roughly (c) Kept in the roof (d) Played with always

Want more Objective Questions like this?
Get the Complete Technical Drawing TD Exam Questions (Obj & Theory); In
editable Ms-word format for any of the SS 1 – 3 Classes
Continue reading to know how

SECTION B (ESSAY)

1. (a) What is technical drawing?
(b) Mention 5 drawing instrument and material for good drawing practice
(c) Explain the following terms
i. Title block
ii. Lettering
iii. Safety

2. (a) Draw line AB 75mm and bisect it
(b) Construct a triangle given the length of the three sides as AB= 80mm
BC=60mm AC=50mm
(c) Mention 3 parts of a circle

3. (a) Given that AC=36mm AB=55mm BC=36mm. Construct a triangle and
circumscribe a circle

(b) List 3 properties of a square
(c) Construct a square ABCD with side AB=65mm

4. (a) Inscribe triangle ABC in a circle where PR=54mm RQ=63.5mm PQ=74.5mm
(b) Mention 4 types of triangles
(c) Mention 2 types of lines used in technical drawing
https://stcharlesedu.com

Technical Drawing Exam Question for SS1-3

To get the complete exam question papers for the subject and any of the classes concern,
then continue reading
https://stcharlesedu.com
How to Get Senior Secondary School TD Exam Questions
Step to get Technical Drawing Exam Questions for SS 1 – 3

1. TAKE ACTION.
Call or Whatsapp us on 08051311885 for cost and account number to make
payment and how to received your Ms-Word/PDF Copy

2. MODE OF PAYMENT.
Mobile Transfer, POS or Direct Bank Deposit.

3. AFTER PAYMENT.
Send us the following
Depositor Name:
Name of Product Paid for:
Valid email address.

4. DELIVERY ASSURANCE.
We will deliver the past question to you, 5 minutes after confirmation of payment to
the email address you will send to us.

Also available for download are other senior secondary school exam questions

Senior Secondary Cross Cutting Subjects Senior Secondary – Business
Civic Education Commerce
English Language Financial Accounting
General Mathematics Insurance
One Trade Subject Office Practice
Marketing Store Management

Senior Secondary – Humanities Senior Secondary – Science
Arabic Language Agricultural Science
Christian Religious Studies Biology
Economics Chemistry
French Computer Studies/Science
Geography Further Mathematics
Government Health Education
Hausa Language Physical Education
History Physics
Igbo Language Technical Drawing
Islamic Studies
Literature-in-English
Music
Visual Arts
Yoruba Language