NEWPORT TOOL & FASTENER CO., INC. - Altitude 800 Corp

NEWPORT TOOL & FASTENER CO., INC.

® Roof Tile Fastening Specialists

ADVANCED ROOF TILE
FASTENING SYSTEMS
& ACCESSORIES

TYLE-TYE STRAP SYSTEM® • Earthquake Resistant - Absorbs Seismic Energy
This is the preferred system where optimum fastening • High Wind Resistant
is required and strict code regulations are in effect. Tie • Protects Waterproofing by Minimizing Penetrations
rods, connectors or tie wires connect each tile into the
Tyle Tye® Strap system that is fastened by ring shank
nails, screws or spikes. The 1” continuous metallic strip
installs under the rows of tile eliminating any pressure
or weight on the strip while maintaining the integrity
of the roof system.

T WISTED WIRE TYLE-TYE SYSTEM®
This continuous system of twisted wire features a spe-
cial anchor that attaches through the underlayment to
wood, concrete, or metal roof decks. Roof tiles are tied
to the loops of the twisted wire Tyle Tye®. The water-
proof membrane is punctured only at anchoring points,
and the appropriate roofing mastic is used to seal these
penetrations.

RINESS® TILE TIE SYSTEM
This single-line tile tie system features a loop and hook
fastener that interlocks the tiles allowing for greater
labor and cost savings. It can be used with most clay
mission or clay shingle tiles.

T YLE-TYE TILE NAIL®
This system is a unique fastener used in the cover por-
tion of clay 2-piece mission tile, or clay “S” tile or most
concrete roof tiles. Tile nail outperforms any direct
deck nailed roof tile fastener by securing the tile at two
points with one fastener; prevents tile fractures or
breaks and uses the uplift forces to drive the nail por-
tion of the fastener deeper into the deck.

Newport Tool & Fastener Company, Inc., 977 Enterprise St., Orange, CA 92867
(800)645-7811 (714)385-1111 Fax (714)385-1312
www.newportfastener.com

2 NEWPORT TOOL & FASTENER CO., INC.

T YLE-TYE® SYSTEMS RINESS® TILE TIE SYSTEM

Tyle-Tye® Systems include the Tyle-Tye® Strap System, the Twisted Use of the Riness® Tile Tie System as directed, results in a mini-
Wire Tyle-Tye® System and the Riness® TileTie System. With these mally penetrated membrane while the Riness® Ties interlock the
fastening methods the only puncture of the membrane is at the tiles together to resist wind damage, earthquake damage, or shift-
anchoring points. These anchoring points are sealed in the appro- ing of tile from other causes.
priate roofing mastic.
The Riness® Tile Tie system consists Riness®
Tyle-Tye® Systems are UBC approved. of a series of interconnecting pre- Tile Tie
Patent #: 5,921,045 and 6,125,592 formed wire ties through the holes of
the tile to provide a continuous Double plate
Patented anchorage against sliding off. Besides anchor assem-
being anchored at the ridge and eave bly
T YLE-TYE® STRAP SYSTEM line, the wire ties are anchored at
intermediate points as required to Wind Lock
avoid overstressing the individual fas- Nose Clip
teners, but in no case longer than 10
Installed by a single The patented Tyle-Tye® Strap system feet. For added protection and in Wind Lock
180º bend of the is used where maximum holding designated high-wind areas, and seis- Nose Clip
wire power is required and for the most mic zones 3 and 4, use the appropri-
Tyle-Tye® Strap stringent of building code regulations. ate size Wind Lock Nose Clip for all Booster Tile
System Each strap is 10 feet long, unless cover tiles or at least the first three
ordered specifically for the exact courses at the eave. Riness Tile Tie® for Riness® Tile Tie Riness® Tile
Connector length of tile run from eave to hip eave course cover to second Tie to double
Nose Clip part of and/or ridge. Once the straps are fas- For further information refer to the tile course tile plate anchor
connector tened to the deck, and the fastening Riness® Tile Tie Specifications.
points are sealed in Tyle-Tye® Chatter
Tyle-Tye® Strap Damper, each tile is quickly connect- Roofing Tip
ed to a punch out providing for a
Connector nose speedy installation. Use like metals for the entire sys- Double plate
clip tem to prevent electrolysis. Use anchor assemblies
The Tyle-Tye® Strap roof tile fastening stainless steel tie wires and stainless
Hurricane system consists of a 1" wide by 24 steel, galvanized steel or brass Anchor ties
Side Clip gauge strap with punch outs every 4" anchors for stainless steel Tyle-Tye®.
to connect each piece of roofing tile, Use copper tie wires and brass Wind Lock
and anchor holes every 4" to nail, anchors for copper Tyle-Tye®. Use Nose Clip
screw or spike the strap securely to brass tie wires and brass anchors
any type of roof deck. Individual tiles for brass Tyle-Tye®. Use galvanized Roofing Tip
are secured to the strap using steel tie wires and galvanized steel
Connectors, Tie Wires or Tie Rods. anchors for galvanized steel Tyle- California State Architectural Code
Besides being anchored at the ridge, Tye®. For installation to steel decks Title 24 provides building specifi-
hip and eave, the Tyle-Tye® Straps are use galvanized steel or stainless cations for all state buildings to
anchored at intermediate intervals as steel fastening systems. protect the safety of the public.
required to avoid overstressing any Tyle-Tye® systems have been part of
one anchor point. In no case shall the For installation to concrete decks, the California State Building Code
anchor spacing be longer than 10 use stainless steel fastening systems Title 24 since 1933.
feet. and stainless steel compression To date there have been no
spikes. When using copper or brass known reported failures of this
For further information fastening systems, use copper, brass system.
refer to the Tyle-Tye® or stainless steel fasteners. When
Strap Specifications. attaching to steel decks, use stain-
less steel or carbon steel self-
drilling screws. For light density
concrete decks and over insulated
decks, please consult the factory.

The ultimate strength of the Tyle-Tye Fastening System is a function of
those forces applying to each anchor point. Anchor spacing depends
upon geographical wind loads, type of roof deck, style of fasteners,
slope and design considerations.

Newport Tool & Fastener Company, Inc., 977 Enterprise St., Orange, CA 92867
(800)645-7811 (714)385-1111 Fax (714)385-1312
www.newportfastener.com

NEWPORT TOOL & FASTENER CO., INC. 3

T WISTED WIRE TYLE-TYE® SYSTEM T YLE-TYE® TILENAIL

Twisted wire Tie wire bridle using 1 tie Twisted Wire Tyle-Tye® is a continu- The Tyle-Tye® TileNail System is a TileNail with clay “S”
wire through both holes of ous element of twisted wire that is unique fastener used in the cover tile
shingle then tied into system attached by means of a special anchor portion of clay, "S" or Mission tile
at 45º angle to the roof deck through the required that incorporates a Wind Lock and a
underlayment. The continuous ele- nail in one fastener. The TileNail
Wind Lock ment consists of two wires twisted eliminates breakage because the nail
Nose Clips together with a loop or eyelet approx- is away from the tile. (They are
imately every six (6) inches. The U.B.C. approved to all slopes and are
Pre-tied Twisted Wire Wood Deck loops or eyelets in the twisted wire particularly suited to mansard appli-
tie wires Tyle-Tye® Anchor are used to accomodate whichever cations.)
wire is selected to fasten individual
Nose Clips roof tiles. The TileNail outperforms any direct TileNail for concrete tile
deck nailed roof tile by securing the
Hurricane A loop in the Twisted Wire Tyle-Tye® tile at two points with one fastener. A
Side Clips is slipped down over the stem of the Wind Lock Nose Clip is incorporated
special anchor, and the two stem ele- into the front part of the TileNail
Double plate ments are then bent apart to engage holding the butt end of the next tile,
Wind Lock Nose Clips wired into anchor assembly the wire tie and to prevent it from while the shaft is slipped into the
Tyle Tye® at eave course slipping off. The double plate anchor hole of the head end of roof tile being
system can be used also to fasten the nailed. In addition to preventing frac-
Twisted Wire Tyle-Tye® to the roof tures and/or breaks of the tile
deck. because the hammer never is near the
brittle clay or concrete, the uplift
Individual roof tiles are tied into the forces acting upon the butt end of the
loops of the Twisted Wire Tyle-Tye® tile will continue to drive the nail
by means of a Tie Wire of similar portion of the fastener deeper into
metal. Besides being anchored at the deck.
ridge, hip and eave, the Twisted Wire
Tyle-Tye® System is anchored at inter- TileNails are available with or with-
mediate intervals as required to avoid out a Wind Lock Nose Clip. When
overstressing any one anchor point. specifying TileNails with Wind Lock
In no case shall the anchor spacing Nose Clip, specify 3" headlap for clay
be longer than 10 feet. "S" tiles and concrete tiles laid with a
3" headlap. For those roof tiles
For further information refer to the requiring a 4" headlap, specify the 4"
Twisted Wire Tyle-Tye® headlap TileNail.
Specifications.
ALSO AVAILABLE
Eave detail with booster tile TileNail with concrete high
Copper and Stainless profile tile at eave with metal
Connection of Tiles into Tyle-Tye® Strap/Twisted Wire Steel Roofing Nails birdstop

Tie Wires Screws for Roof Tile and Double Plate Anchor
Wrap each tie wire through the Tyle-Tye® System
tile, diamond or punch out then Stainless Steel or F.M. Stainless Steel or F.M.
twist back on itself a minimum of A California Architect invented the
3 full revolutions. Twisted Wire Tyle-Tye® system in approved 2” or 3” approved galvanized 3”
1929 after a devastating earthquake
Connectors damaged tile roofs in Southern galvanized insulation plate insulation plate
Put end through the tile until the nose California. It has been used for over
hook is in place, then with a good pair of 70 years to fasten any type of roof- Twisted Wire Tyle-Tye®
Linesmen’s pliers push the straight end into ing tile, to any type of roof deck
the punch out and bend it back past the and to any slope. Extra tiles or Insulation
boosters, mortar, staggered expo-
shank. sures, headlaps and other types of Membrane Stainless Steel or F.M. 16-24 ga.
roof tile installation designs can be approved15 ga. metal decking
Tie Rod achieved using this multi-purpose coated roofing screw
Put tie rod through the tile and bend it back roof tile fastening system.
parallel to the plane of the tile, then put the
other end through a punch out, or diamond
and bend it back past the shank

Newport Tool & Fastener Company, Inc., 977 Enterprise St., Orange, CA 92867
(800)645-7811 (714)385-1111 Fax (714)385-1312
www.newportfastener.com

4 NEWPORT TOOL & FASTENER CO., INC.

WIND LOCK NOSE CLIPS HURRICANE SIDE CLIPS
Also known as "hurricane clips, side
clips or grip clips", the Hurricane
Side Clip is a strap-type locking

power and are used in high wind device for the side edge of several
designated areas. Wind Lock Nose
Clips are compatible with all meth- types of roofing tile. It provides max-
ods of tile attachment and are rec-
ommended for all roof tiles installed imum holding power when used in
at slopes 7:12 or greater.
Nose Clip portion of the conjunction with Wind Locks and
Tile-Tye® TileNail. Available in a squared configuration
designed to better fit all different one of the other Tyle-Tye® Systems.
Also known as "Tile Locks, Nose Clips or roof tile profiles tightly.
Butt Hooks", Wind Lock Nose Clips are Manufactured from type 300 series Hurricane Side Clips are especially
for use with clay and concrete roofing (.090" dia., 2.3mm) Stainless Steel
tiles to all slopes. They provide a locking or 11 gauge (.120" dia, 3mm) suited for concrete roof tiles.
device for the butt edge of each cover Electro-galvanized Steel (10 ga.
tile. Wind Locks achieve greater holding Brass is available by special Advantages of the Hurricane Side
request).
Clip include excellent holding power

and invisibility of the part after

TileNail Nose Clip Perfect placement of installation. Hurricane Side Clips are
Hurricane Side Clip U.B.C. approved for all slopes.

SAMPLING OF COMPLETED PROJECTS Storm Lock Side Clips and Batten
Clips are manufactured from 1/2"
(13mm) x 18 gauge Electro-galva-
nized Steel or 1/.2" (13mm) x
18gauge type 300 series Stainless
Steel. 1/2" x 18gauge brass is avail-
able upon special request.

Hotel and Resort First two courses of TileNail with Nose Clip for con-
crete high profile tile
Aloha Towers, Honolulu, HI
Avalon Casino, Catalina Island, CA T YLE-TYE® CHATTER
Leo Palace Resorts, Guam DAMPER MASTIC
Manele Bay Resort, Lanai, HI
Ritz Carlton Hotels
Royal Hawaiian Hotel, HI

Government and Industrial Tyle-Tye® Chatter Damper Mastic Tyle-Tye® Chatter Damper is a tripolymer
adhesive designed to function as a tile
El Toro Marine Base, Orange County, CA mastic and buffer, or pillow, between tiles
Anderson AFB, Guam to cushion the "chatter" effect of clay or
Brazilian Embassy, Washington, DC concrete roof tiles, or slates, that have the
Camarillo State Hospital , CA tendency to chatter in the wind. Tyle-Tye®
Fort Ord Army Base, Monterey, CA Chatter Damper is used to complement
French Embassy, La Paz, Bolivia Wind Lock Nose Clips, Hurricane Side
Governors Mansion, Guam Clips and TileNail/Hurricane Spike fas-
Hoag Hospital, Newport Beach, CA teners in high wind areas and seismic
Honolulu Police Station, HI zones 3 and 4. Tyle-Tye® Chatter Damper
King Kamahameha High School, HI has exceptional flexibility, adhesion
King Khalid Military City, Saudi Arabia strength, and resistance to UV, with life
March Air Force Base, CA expectancy exceeding 50 years. Tyle-Tye®
McCallen Airport,TX Chatter Damper has been approved by
Richard Nixon Library,Yorba Linda, CA ICBO as an approved roofer's mastic.
Port Hueneme Naval Base, Oxnard, CA
Randolph Air Force Base,TX Commercial and Entertainment
Ronald Reagan Library, Simi Valley, CA
Scofield Barracks, HI Historical Restoration Automobile Club Hdqtrs., Los Angeles, CA Paramount Studios, Los Angeles, CA
Stanford University, Los Altos, CA Brea Mall, Brea, CA Seaport Village, San Diego, CA
State Capital, Sacramento, CA Delancy Street Center, San Francisco, CA Del Mar Race Track, Del Mar, CA Warner Brothers Studios, Los Angeles, CA
U.S. Embassy, El Salvador Gary Cooper Mansion, Beverly Hills, CA Desert Inn Hotel & Casino, LasVegas, NV Fashion Island Shopping Center, Newport Beach, CA
University of California, Berkeley, CA Grand Ole Opry, Nashville,TN
University of California, Los Angeles, CA Hearst Castle, San Simeon, CA Disney Tower of Terror, FL
University of So. Florida,Tampa, FL Mission San Juan Capistrano, CA
University of So. California, Los Angeles, Old Town, San Diego, CA Disneyland, Anaheim. CA
State Capitol, Harrisburg, PA
Wingspread Estate, Racine, WI Disneyland,Tokyo, Japan

Gene Autry Museum, Los Angeles, CA

Hass School of Business, Berkeley, CA

Hess Oil Project,Virgin Islands

Lockheed Corp. Hdqtrs., Calabasas, CA

Newport Tool & Fastener Company, Inc., 977 Enterprise St., Orange, CA 92867
(800)645-7811 (714)385-1111 Fax (714)385-1312
www.newportfastener.com