YKK Guide

> YHS 50 FS/FI
Impact Resistant and Blast
Mitigation Storefront System

Benjamin Upper School

YHS 50 low pressure configuration reduces installation time and
installed cost. Medium and high pressure configurations reach
higher spans and greater impact resistance. This system can be
inside or outside glazed for greater jobsite flexibility.

YHS 50 FS & YHS 50 FI are high performance storefront systems
designed for monolithic glazing (FS) or for insulating glass (FI) 1” to
1-5/16” thick. With varied infill and components, YHS 50 can meet
the demanding requirements of both Impact Resistance and Blast
Mitigation. The system integrates with H Series and HL Series
entrances with medium or wide stiles. Entrances feature a wide variety
of tested and approved hinging and locking hardware, including rim
panic and concealed vertical rod exit devices.
FEATURES:
n Hurricane Impact - Large and Small Missle
w IBC and Florida Product Approval
w Wind Zone 3 & Florida High Velocity Hurricane Zone (HVHZ)
w Approved for Missile Level E - Essential Facilities
n Blast Mitigation - Static and Dynamic Analysis
capability to meet DoD, GSA and VA standards
n Spans to 144”; accomodates glass sizes to 50SF
n Design Pressures to 90 psf
n Engineered corners reduce job specific engineering
n Inside or outside glazing available

n Integrates with ThremaShade® and Luminance®
sun control products and YKK AP venting windows

Entrances | Storefronts | Curtain Walls | Sun Controls | Windows | Balcony Doors

> YHS 50 FS/FI

Impact Resistant and Blast Mitigation Storefront System

• Low pressure options – fewer parts and anchors for lower installed cost
• Taller spans & higher design pressures – less cost compared to curtain wall
• Inside Glazing – lower cost in above grade applications; solves rough terrain and difficult street access issues
• Large Missile E – greater protection for essential facilities such as hospitals, police stations and shelters

PERFORMANCE SUMMARY: MISSILE D MISSILE E

Air Infiltration (ASTM E 283): 0.06 CFM / FT² @ 6.24 PSF (299 Pa) Building codes now call for Missile E protection for essential
Water Infiltration (ASTM E 331): 12 PSF (575 Pa) facilities (Risk Category 4) when the wind speed is 150 mph
or greater. Missile E systems must withstand more than twice
YHS 50 FI Acoustical and Thermal:
Acoustical Performance (AAMA 1801): the impact energy compared to Missile D
STC 1-5/16” Laminated - 39
OITC 1-5/16” Laminated - 34
Thermal Performance (AAMA 507, AAMA 1503, NFRC 100):
Frame CRF = minimum of 35
Overall System U-factor = 0.49 (using Ucog of 0.29)

YHS .060 DESIGN PRESSURE 144” 108” to OUTSIDE IMPACT INSIDE IMPACT
SYSTEM SentryGlass SPAN 120” GLAZE MISSILES GLAZE ESSENTIAL
50 65-70 90 SPAN FACILITIES
50 PSF A&D

YHS 50 FS

YHS 50 FI

YHS 50 TU

INDUSTRY-LEADING SILL FLASHING DESIGN

Taller back leg - Enhanced water resistance
(12 psf) in the field and in testing

Patented 3 Point End Dam Attachment -
Greater protection against handling damage
and building settling

No blind seals - Eliminates secondary
penetration of the sill flashing

For additional information on architectural aluminum products visit our web site at www.ykkap.com. 02-5006-04
©2016 YKK AP America Inc. is a subsidiary of YKK Corporation of America.

> YHS 50 TU
Thermally Broken Impact Resistant and
Blast Mitigation Storefront System

Alice Harte Charter School

YHS 50 TU is a high performance storefront system designed for
insulating glass 1" to 1-5/16" thick and tested to meet the most
demanding conditions. With varied infill and components, YHS 50 TU
can meet the requirements for Impact Resistance, Blast Mitigation
or both. YHS 50 TU is thermally broken by means of a poured and
debridged pocket that employs ThermaBond Plus® to greatly improve
the adhesion of the polyurethane to the extruded aluminum. The
system integrates with H Series and HL Series entrances with
medium or wide stiles. Entrances feature a wide variety of tested
and approved hinging and locking hardware, including rim panic and
concealed vertical rod exit devices.

FEATURES:

n Hurricane Impact - Large and Small Missle
w IBC and Florida Product Approval
w Wind Zone 3 & Florida High Velocity Hurricane Zone (HVHZ)
w Approved for Missile Level E - Essential Facilities
n Blast Mitigation - Static and Dynamic Analysis
capability to meet DoD, GSA and VA standards
n Spans to 144”; accomodates glass sizes to 50SF
n Design Pressures to 90 psf
n Engineered corners reduce job specific engineering
n Inside or outside glazing available

n Integrates with ThremaShade® and Luminance® sun
control products and YKK AP venting windows

Entrances | Storefronts | Curtain Walls | Sun Controls | Windows | Balcony Doors

> YHS 50 TU

Thermally Broken Impact Resistant and Blast Mitigation Storefront System

PERFORMANCE SUMMARY: North Charleston Public Works

Air Infiltration (ASTM E 283): 0.06 CFM / FT² @ 6.24 PSF (299 Pa)
Water Infiltration (ASTM E 331): 12 PSF (575 Pa)
YHS 50 FI Acoustical and Thermal:
Acoustical Performance (AAMA 1801):

STC 1-5/16” Laminated - 39

OITC 1-5/16” Laminated - 33
Thermal Performance (AAMA 507, AAMA 1503, NFRC 100):
Frame CRF = minimum of 59

Overall System U-factor = 0.45 (using Ucog of 0.29)

YHS .060 DESIGN PRESSURE 144” 108” to OUTSIDE IMPACT INSIDE IMPACT
SYSTEM SentryGlass SPAN 120” GLAZE MISSILES GLAZE ESSENTIAL
50 65-70 90 SPAN FACILITIES
50 PSF A&D

YHS 50 FS

YHS 50 FI

YHS 50 TU

INDUSTRY-LEADING SILL FLASHING DESIGN

Taller back leg - Enhanced water resistance
(12 psf) in the field and in testing

Patented 3 Point End Dam Attachment -
Greater protection against handling damage
and building settling

No blind seals - Eliminates secondary
penetration of the sill flashing

For additional information on architectural aluminum products visit our web site at www.ykkap.com. 02-5008-05
©2016 YKK AP America Inc. is a subsidiary of YKK Corporation of America.

> Model 35H/50H

YKK AP’s ProTek® Impact Resistant
and Blast Mitigating Entrances

Protection You Can Count On

The industry’s most durable entrance system is now
available in medium and wide stile versions. In addition
to a comprehensive array of locking and hinging options,
this product is available with monolithic or 1” insulating
laminated glass for medium and wide stile applications.
Mid-Rail and bottom rail options provide additional design
flexibility for the specifier.

YKK AP has also addressed ongoing maintenance in
abusive environments, such as schools and military bases.
To reduce maintenance costs choose either rim panic
exit devices combined with an impact rated aluminum
removable mullion, or single point locks paired with flush
bolts on the inactive panel. These institutional grade
entrance systems provide maximum security under the
most demanding conditions without the need for steel
reinforcing. They also integrate with YHS storefront and
YHC curtain wall framing systems.

Model 35H and 50H entrances are Large and Small Missile
Impact resistant tested, as well as Blast Mitigation
Tested. With the expansion of hardware and performance
options, they are your single source for hurricane resistant,
government, and DoD applications.

Product Benefits

 Large & Small Missile Impact – To 90 PSF
Florida Product Approval – HVHZ

 Blast Mitigation Testing – ASTM F 1642 –
Minimal Hazard

 YKK AP VersaJamb® Door Frame
 Water Performance – ASTM E 331 – 10.5 PSF

Entrances | Storefronts | Curtain Walls | Sun Controls | Windows | Balcony Doors

> Model 35H/50H

YKK AP’s ProTek® Impact Resistant and Blast Mitigating Entrances

Monolithic or IGU Glazing Pocket

Monolithic and insulating glazing utilize different rail designs

Thermal Performance

Improved thermal performance can be achieved with
Insulating Glass. Entrances have been thermally tested
utilizing insulating glass with 0.29 center of glass “U” factor.

Glazing Options

For reduced installation labor, dry glaze solutions (to 90 PSF)
are available. Wet and Dry Glaze options are available for
both hurricane impact and blast mitigation.

Integral Muntins

For increased aesthetic possibilities Insulating Glass units
can be ordered with internal muntins.

Door Corner Standard Entrances
Lifetime Warranty
 Singles: 3'-0" x 7'-0" & 3'-0" x 8'-0"
 Pairs: 6'-0" x 7'-0" & 6'-0" x 8'-0"
 Rixson Pivot, Butt Hung and Continuous Hinge
 Single and 3-Point Locks for Single Doors,

5-Point Locks for Pairs
 Rim and CVR Exit Devices

Custom Entrances

 Singles: Up to 4'-0" x 8'-0"
 Pairs: Up to 8'-0" x 8'-0"
 Pairs: Up to 7'-0" x 8'-0" with Rim Panic
 Standard and Custom Hardware

For additional information on architectural aluminum products offered by YKK AP America Inc. visit our web site at www.ykkap.com.

©2013 YKK AP America Inc. is a subsidiary of YKK Corporation of America. 01-5001-03

> YHC 300 OG

Hurricane Impact and Blast Mitigation

Curtain Wall System

Single and Twin Spans Single and Twin Spans Monumental Applications
Design Pressure: Design Pressure: Design Pressure:
45-55 PSF 65-90 PSF 90-130 PSF

Protection For Every Application Product Benefits:

YHC 300 OG is a high performance curtain Fully tested to ASTM and TAS standards
wall system designed and tested to provide
innovative impact and blast solutions for a Florida Product Approvals for large and small missile impact including
wide range of applications and design HVHZ applications
pressures from 45 PSF all the way to
130 PSF. The 3” face dimension ensures Mullion options provide the most cost effective solutions across all pressures and
recommended glass clearances are design applications
maintained. Dry glazing options (for all
design pressure ranges) slash installation 15/16” glass bites maintain GANA guidelines of 1/4” clearance to reduce
time for quicker building dry-in. glass breakage

Designed for single and multispan applications

Achieve 17’ single spans at 90 PSF

Accommodates monolithic and insulating glass

Dry glazing eliminates cure time, dust settling on uncured sealant and helps to
ensure proper glass/frame integration

Entrances | Storefronts | Curtain Walls | Sun Controls | Windows | Balcony Doors

> YHC 300 OG
Hurricane Impact and Blast Mitigation Curtain Wall System

Specifications Hurricane Impact Resistance
ICC Compliant and FBC Statewide approvals –
Deflection: Maximum allowable deflection in any member when tested HVHZ (High Velocity Hurricane Zone)
in accordance with ASTM E 330 with allowable stress in accordance ASTM E 1886 / 1996 and TAS 201 – 203
with AA Specifications for Aluminum Structures. Large Missile Level E – Essential Facilities
Large Missile Level D & Small Missile Level A
a. For spans less than 13'-6" (4.1m): L/175 or 3/4”
(19.1mm) maximum. Blast Mitigation

b. For spans greater than 13'-6" (4.1m) but less than 40'-0" “Low Hazard” per ASTM F 1642 Test @ 6 psi / 41 psi – ms
(12.2m): L/175 or L/240 + 1/4" (6.4mm).
Dry Glazing option shown. Visit www.ykkap.com for glazing
Thermal Movement: Provide for thermal movement caused by 180 options and CSI Specs by performance / glazing type
degrees F. (82.2 degrees C.) surface temperature, without causing
buckling stresses on glass, joint seal failure, undue stress on structural 3” [76.2mm]
elements, damaging loads on fasteners, reduction of performance.
5-5/8” [142.9mm]
Air Infiltration: Completed curtain wall systems shall have 0.06 CFM/FT²
(1.10 m³/h·m²) maximum allowable infiltration when tested in accordance 1/4” Minimum
with ASTM E 283 at differential static pressure of 6.24 PSF (299 Pa). Glass Clearance

Water Infiltration: No uncontrolled water on indoor face of any Typical
component when tested in accordance with:
Horizontal
a. ASTM E 331 at a static pressure of 20 PSF (957 Pa).
b. AAMA 501.1 at a dynamic pressure of 20 PSF (957 Pa). 45-55 PSF OPTION

Thermal Performance: When tested in accordance with AAMA 1503.1 Vertical
and NFRC 102:
7-11/16” [195.6mm]
a. Thermal Transmittance U Value: 0.42 BTU/HR/FT²/ºF or less.
b. Condensation Resistance Factor (CRFf): A minimum of 72. Optional Steel
Reinforcement
Sound Transmission: When tested in accordance with AAMA 1801
using 1/4" laminated exterior, 1/2" air space, and 1/4" laminated interior: Horizontal

STC: 37 65-90 PSF OPTION
OITC: 32

Seismic Movement: When tested in accordance with AAMA 501.4:
a. Inter-story Differential Lateral Movement Test: Passed with
design displacement of 0.010 times the story height and
meets the performance criteria for a Highest Occupancy
Assembly (Group III in NEHRP Provisions).
b. Seismic Movement Test: Passed at 1.5 times design
displacement.

*Thermal and sound performance testing conducted with medium pressure components

Vertical

10-1/2” [266.7mm]

Horizontal

Optional Steel
Reinforcement

90-130 PSF OPTION

Vertical

For additional information on architectural aluminum products offered by YKK AP America Inc. visit our web site at www.ykkap.com.

©2010 YKK AP America Inc. is a subsidiary of YKK Corporation of America. 04-5014-00

> YHC 300 IG

Impact Resistant and Blast Mitigation
Inside Glazed Curtain Wall System

SYSTEM DESCRIPTION:

YHC 300 IG (Inside Glazed) is a high performance
curtain wall system designed and tested to meet
the most demanding conditions. With varied infill
and components, YHC 300 IG can meet the
requirements for Impact Resistance, Blast
Mitigation or both. The system features a 3”
wide face dimension to permit the glass
engagement necessary for higher design
pressures and accommodates 1/4” to 9/16” single
glazing or 1” to 1-5/16” insulated glazing.

OPTIONS & FEATURES:

Large & Small Missile
Small Missile is Dry Glazed
Large Missile is Wet Glazed

ASTM E 1886 / 1996, TAS 201 – 203
Tested to +/- 120 psf *
Florida State-Wide Product Approval

Blast Mitigation
YHC 300 IG meets UFC 4-010-01
prescriptive standard in accordance
with 2007 revisions.
Model 35H - “Low Hazard” per ASTM
F 1642 Test @ 6 psi / 41psi-ms

Model 35H Single Doors up to 4’–0” x 8’–0”
Model 35H Pairs up to 8’-0” x 8’-0”

*Contact YKK AP Engineering for Job Specific
Wind Load analysis at higher levels.

Entrances | Storefronts | Curtain Walls | Sun Controls | Windows | Balcony Doors

> YHC 300 IG
Impact Resistant and Blast Mitigation
Inside Glazed Curtain Wall System Specifications

1.01SUMMARY

A. Section Includes: Aluminum Curtain Wall Systems
1. YKK AP Series YHC 300 IG (Inside Glazed) Hurricane Impact Resistant Aluminum Curtain Wall System.

B. Related Sections:
1. 08 41 13 35H Impact Resistant Heavy Duty Swing Doors.
2. 08 41 13 YHS 50 Impact Resistant Aluminum Store Front Systems.
3. Glass: Contact YKK AP for approved glass types.
4. Glazing: Dow Corning® 995 Structural Silicone Adhesive for large missile.

1.02 SYSTEM DESCRIPTION

A. Performance Requirements: Provide aluminum curtain wall systems that comply with performance requirements indicated,
as demonstrated by testing manufacturer's assemblies in accordance with Florida Building Code Test Protocol TAS-201,
TAS-202 and TAS-203, and Test Protocols ASTM E 330, ASTM E 1886 & ASTM E 1996.
1. Wind Loads: Completed curtain wall system shall withstand wind pressure loads normal to wall plane indicated:
a. Positive Pressure:
b. Negative Pressure:
2. Deflection: Maximum allowable deflection in any member when tested in accordance with ASTM E 330 with allowable stress in
accordance with AA Specifications for Aluminum Structures:
a. L/175 or 3/4" (19.1mm) maximum for spans less than 13’-6” (4.1m).
b. L/175 or L/240 + 1/4" (6.4mm) for spans greater than 13'-6" (4.1m) but less than 40'-0" (12.2m).
3. Thermal Movement: Provide for thermal movement caused by 180 degrees F. (82.2 degrees C.) surface temperature, without
causing buckling stresses on glass, joint seal failure, undue stress on structural elements, damaging loads on fasteners, reduction
of performance, or detrimental effects.
4. Air Infiltration: Completed curtain wall systems shall have 0.06 CFM/FT² (1.10 m³/h·m²) maximum allowable infiltration when tested
in accordance with ASTM E 283 at differential static pressure of 6.24 PSF (299 Pa).
5. Water Infiltration: No uncontrolled water on indoor face of any component when tested in accordance with ASTM E 331 at test
pressure differential of 20 PSF (958 Pa). Water test to be performed immediately after design pressure test.
6. Thermal Performance: When tested in accordance with AAMA 1503.1 and NFRC 102:
a. Condensation Resistance Factor (CRF): A minimum of 63.
b. Thermal Transmittance U Value: 0.49 BTU/HR/FT²/ºF or less.

2.01 MANUFACTURERS

A. Acceptable Manufacturers: YKK AP America Inc.
1. Curtain Wall System: YKK AP YHC 300 IG Curtain Wall System.

B. Curtain Wall Framing System:
1. Description: Framing shall be thermal improved. Horizontal and vertical members shall have a nominal face dimension of 3 inches,
depth as indicated on shop drawings. Framing system shall provide a flush glazed appearance on all sides with no protruding glass
stops. Framing system shall allow inside setting of glazing infills.
2. Glazing: Manufacture's standard EPDM glazing gaskets to inhibit water infiltration at the exterior and EPDM glazing gaskets, Dow
Corning® 995 Structural Silicone Adhesive with fixed stops at the interior; interior spacers/gaskets are to be silicone or silicone
compatible for large missile. EPDM interior gasket for small missile and non-impact applications.

2.02 MATERIALS

A. Extrusions: ASTM B 221 (ASTM B 221M), 6063-T5 and 6063-T6 Aluminum Alloys.

2.03 ACCESSORIES

A. Manufacturers Standard Accessories:
1. Fasteners: Zinc plated steel concealed fasteners; Hardened aluminum alloys or AISI 300 series stainless steel fasteners. Joint
fasteners may be concealed.
2. Sealant: Non-skinning type, AAMA 803.3
3. Glazing: Setting blocks, edge blocks, and spacers in accordance with ASTM C 864, shore durometer hardness as
recommended by manufacturer; Exterior EPDM gaskets in accordance with ASTM C 864.
4. Glazing Adhesive: Dow Corning® 995 Structural Silicone.

2.06 FINISHES

A. Anodic Coating: Electrolytic color coating followed by an organic seal applied in accordance with the requirements of AAMA 612-02
B. High Performance Organic Coating Finish: Factory applied two-coat 70% Kynar resin by Auto Chem or 70% Hylar resin by Ausimont,

fluoropolymer based coating system, Polyvinylidene Fluoride (PVF-2), applied in accordance with YKK AP procedures and meeting
AAMA 2605 specifications.

For additional information on architectural aluminum products offered by YKK AP America Inc. visit our web site at www.ykkap.com.

©2009 YKK AP America Inc. is a subsidiary of YKK Corporation of America. 04-5009-02



YKK AP is part of this select nationwide network of exceptional coating applicators
whose facilities and quality control processes are rigorously audited by PPG to deliver
the highest possible level of product quality, customer service and technical expertise.

Highest Quality Aluminum Duranar® Coatings Advantage
Billets and Extrusions
With a proven track record of over 40 years,
YKK AP controls every step in the manufacturing Duranar coatings are formulated with 70%
process under one roof. To ensure the quality and the PVDF fluoropolymer resin and proprietary PPG
integrity of the aluminum alloy we cast our own alu- resin, pigments and solvents. This gives
minum logs for extrusion at our ISO 14001 certified Duranar coatings durability and colorfastness
facility located in Dublin, Georgia. unmatched in the industry.
These logs include a minimum of
30% pre-consumer recycled
aluminum content.

Chemical Conversion Coating

PPG's pretreatment is recognized as the most effective pretreatment for aluminum pro-
viding the maximum corrosion protection available. Outstanding surface preparation is
the key to achieving AAMA 2605 performance, the most stringent paint performance
standard in the industry.

Chicago Atlanta Boston Baltimore
1000 Stevenson Court 8140 Troon Circle Eight Connector Road 8680 Greenwood Place
Suite 101 Suite 110 Andover, MA 01810 Savage, MD 20763
Roselle, IL 60172-4314 Austell, GA 30168 Tel: 978-749-9554 Tel: 301-498-3650
Tel: 630-582-9602 Tel: 678-945-6190 Fax: 978-749-2915 Fax: 301-498-3755
Fax: 866-955-2441 Fax: 678-945-6328
Dallas Greensboro
Houston Cincinnati 2025 W. Belt Line Road 4524 Green Point Drive
3550 Brittmoore Road 5406 Spellmire Drive Suite 130 Suite 106
Suite 200 Cincinnati, OH 45246 Carrollton, TX 75006 Greensboro, NC 27410
Houston, TX. 77043 Tel: 513-942-7200 Tel: 972-245-9551 Tel: 336-665-1963
Tel: 713 329-9551 Fax: 513-682-2123 Fax: 972-245-9522 Fax: 336-665-1965
Fax: 713 939-0811
Orlando Headquarters For further information, please
7608 Currency Drive 7680 The Bluffs contact your local YKK AP Sales
Orlando, FL 32809 Suite 100 Office, call 1- 800- 955- 9551
Tel: 407-856-0660 Austell, GA 30168 and ask for an architectural sales
Fax: 407-856-0090 Tel: 678-838-6000 representative, or visit us at
Fax: 678-838-6001 www.ykkap.com.

©2011 YKK AP America Inc. is a subsidiary of YKK Corporation of America. Printed in the U.S.A. | 17-1001-01

YKK AP Anodized Plus®

Standard Matte Finish

*YS1N Clear YH3N Champagne
YB1N Medium Bronze *YB5N Dark Bronze

*YW3N White *YK1N Black

*Normally in stock for quick delivery, consult your local YKK AP Service Center for availability.

The color samples shown on this page are reproduced as closely as possible to the actual
YKK AP Anodized Plus® colors and are to be used only as a guide. For actual anodized aluminum
samples contact your local YKK AP sales representative at 1-800-955-9551 or www.ykkap.com.

Anodized Plus® is a registered trademark of YKK AP America Inc.

©2010 YKK AP America Inc. is a subsidiary of YKK Corporation of America. Printed in the U.S.A.

What is Anodized Plus®? It is more Introduction to
innovation from YKK AP. Anodized YKK AP Anodized Plus®
Plus provides a unique protective
seal on anodic finishes. Its anodic Conventional Anodized VS. YKK Anodized Plus®
coating combined with an organic
seal offers the dual benefits of The synergistic effects of this new aluminum finish result in
enhanced durability and resistance important advantages:
to staining and degradation.
 Increased resistance to chemical corrosion.
Conventional anodic coatings rely  Superior color and gloss retention.
on hot water or steam sealing to  Enhanced protection of aluminum substrate.
close the porous anodic layer; how-  10 Year Warranty on YS1N (Clear), YH3N (Champagne),
ever, it is not possible to close every
pore using this process. YKK AP YB1N (Med. Bronze), YB5N (Dk. Bronze) & YK1N (Black).
Anodized Plus replaces the conven-
tional sealing process with a unique See YKK AP Anodized Plus brochure for more information.
non-aqueous, electrodeposited
organic seal that provides complete Mortar Resistance & CASS Corrosion Resistance Test
protection for the anodic oxide and
the pigmentation coating.

YKK AP controls every step in the
manufacturing process under one
roof. To ensure the quality and the
integrity of the aluminum alloy we
cast our own aluminum logs for
extrusion. Our method of electrolytic
coloring by vertical immersion pro-
vides unmatched color consistency
and eliminates the need for color
range samples. The colors available
are white, black, clear, champagne,
medium and dark bronze.

YKK AP Anodized Plus meets all of
the requirements for the newest
standard for anodized finishes,
AAMA 612. To ensure that the
anodized finish on your next project
meets your aesthetic requirements
and stands up to chemicals com-
monly found on construction sites
and harsh environments specify
AAMA 612 — specify YKK AP
Anodized Plus.

This brochure is intended for product information only. Contents are subject to change without notice
and should not be construed as representations or warranties.

©2010 YKK AP America Inc. is a subsidiary of YKK Corporation of America. 17-1002-00

> YKK AP

Anodized

Plus®

The anodized finish with proven advantages.

Entrances | Storefronts | Curtain Walls | Sun Controls | Windows | Balcony Doors

An Introduction to Anodized Plus®

Conventional Anodized Vs. YKK AP Anodized Plus®

AAMA 611 – Conventional Anodized Finish AAMA 612 – YKK AP Anodized Plus® Finish

Porous Aqueous Seal Electro-Deposition
Organic Seal
Anodic Oxide
Plus Electrolytic Anodic Oxide
Pigmentation Coating Plus Electrolytic
Pigmentation Coating

The synergistic effects of this new aluminum finish result in important advantages:
• Increased resistance to chemical corrosion.
• Superior color and gloss retention.
• Enhanced protection of aluminum substrate.

What is Anodized Plus? It is more innovation from YKK AP. Anodized Plus provides a unique protective seal on anodic finishes.
Its anodic coating combined with an organic seal offers the dual benefits of enhanced durability and resistance to staining and
degradation.

Conventional anodic coatings rely on hot water or steam sealing to close the porous anodic layer; however, it is not possible to
close every pore using this process. YKK AP Anodized Plus replaces the conventional sealing process with a unique non-aqueous,
electrodeposited organic seal that provides complete protection for the anodic oxide and the pigmentation coating.

YKK AP controls every step in the manufacturing process under one roof. To ensure the quality and the integrity of the aluminum alloy
we cast our own aluminum logs for extrusion. Our method of electrolytic coloring by vertical immersion provides unmatched color
consistency and eliminates the need for color range samples. The colors available are white, black, clear, champagne, medium and
dark bronze.

YKK AP Anodized Plus meets all of the requirements for the newest standard for anodized finishes, AAMA 612. To ensure that the
anodized finish on your next project meets your aesthetic requirements and stands up to chemicals commonly found on construction
sites and harsh environments specify AAMA 612 — specify YKK AP Anodized Plus.

All YKK AP products are created in facilities that are models of energy
efficiency and environmental responsibility. YKK AP’s U.S. manufacturing
plant in Dublin, Georgia, is ISO 14001 certified and has a 73% recycling
rate. The plant:

• Recycles 100% of aluminum waste on-site

• Has reduced the amount of other waste materials sent to
the landfill by 40%

• Uses regenerative burners to save 50% on the melting/casting
operation’s fuel consumption

• Captures and burns 93% of all solvent emissions from the paint line

• Uses state-of-the-art techniques for waste water treatment

COMPARISON OF ANODIZED FINISH STANDARDS

PERFORMANCE

TEST AAMA 612 AAMA 611

Coating Thickness CLASS I CLASS II
Color Uniformity
FINISH Hardness 0.7 mils (18 microns) 0.7 mils (18 microns) 0.4 mils (10 microns)
Muriatic Acid Resistance
Mortar Resistance Samples Shale Not Differ More Than 5 Delta E Samples Shall Not Differ More Than 5 Delta E
Nitric Acid Resistance
Detergent Resistance Minimum 3H Hardness Michael Clark Abrasion Test
Window Cleaner Resistance
Craze Resistance No Blistering & No Visual Change in Appearance No Test Specified
Humidity Resistance
STRENGTH Salt Spray Resistance No Blistering & No Visual Change in Appearance No Test Specified
Weathering
Gloss Retention Maximum Change in Color of 5 Delta E No Test Specified
Erosion
Seal Test No Blistering & No Visual Change in Appearance No Test Specified

No Blistering & No Visual Change in Appearance No Test Specified

No Crazing Below a Metal Temperature of 82º C (180º F) No Crazing Below a Metal Temperature of 82º C (180º F)

Only a Few Small Blisters As Defined by ASTM D 714 No Test Specified

DURABILITY Samples Exposed for 4,000 hrs ASTM D 1564 3,000 hrs ASTM B 117 1,000 hrs ASTM B 117

5-Year South Florida Exposure 5-Year South Florida Exposure

Shall Be a Minimum of 50% After 5 Years South Florida No Test Specified

Less Than 10% Film Thickness Lost After 5 Years South Florida No Test Specified

Quality of Seal Determined Through Performance Tests Shown Above Maximum Weight Loss of 40mg/cm²

An anodized finish that is tough enough to resist damage from construction site chemicals, harsh environments and now
Father Time. YKK AP’s Anodized Plus® material shipped from the Dublin Manufacturing Facility after August 1, 2005, will

meet or exceed all of the requirements for AAMA 612 — the latest standard for anodized finishes.

Specify AAMA 612 — Specify YKK AP Anodized Plus®, Now With 10 Year Finish Warranty*

MURIATIC ACID NITRIC ACID WINDOW CLEANER
RESISTANCE RESISTANCE RESISTANCE

YKK AP CONVENTIONAL YKK AP CONVENTIONAL YKK AP CONVENTIONAL
ANODIZED PLUS® ANODIZING ANODIZED PLUS® ANODIZING ANODIZED PLUS® ANODIZING

MORTAR DETERGENT SALT SPRAY
RESISTANCE RESISTANCE RESISTANCE

YKK AP CONVENTIONAL YKK AP CONVENTIONAL YKK AP CONVENTIONAL
ANODIZED PLUS® ANODIZING ANODIZED PLUS® ANODIZING ANODIZED PLUS® ANODIZING

Anodizing is one of the most beautiful, unique and economical ways to finish architectural aluminum. The anodizing process enhances the intrinsic
luster of aluminum and simply can not be duplicated with paint. Architects and designers desire the appearance of anodized finishes, but are
concerned with the vulnerability of the finish to staining and degradation. In an attempt to improve the durability of anodized finishes manufacturers
have increased the thickness of the oxide coating. But, this simply masks the problem and does not address the real issue. The inherent weakness
of the conventional anodizing process is the inadequate seal of the anodic pores not the thickness of the oxide coating. Even the smallest openings
in the seal leaves the anodized finish vulnerable to attack. In 1965 Honny Chemical developed a new sealing process that seals 100% of the pores
100% of the time; this is the sealing process used for YKK AP Anodized Plus®.

*YW3N finish is warranted for 5 years.

YKK AP America Inc.

YKK AP maintains a state-of-the-art ISO 14001 certified manufacturing facility in Dublin, Georgia.

Service Centers Boston Baltimore Chicago Cincinnati

Atlanta Eight Connector Road 6670 Business Parkway 1000 Stevenson Court 5406 Spellmire Drive
Andover, MA 01810 Suite 104 Suite 101 Cincinnati, OH 45246
8140 Troon Circle Tel: 978-749-9554 Elkridge, MD 21075 Roselle, IL 60172-4314 Tel: 513-942-7200
Suite 110 Fax: 978-749-2915 Tel: 410-796-1001 Tel: 630-582-9602 Fax: 513-682-2123
Austell, GA 30168 Fax: 410-796-2031 Fax: 866-955-2441
Tel: 678-945-6190 Greensboro Headquarters
Fax: 678-945-6328 Houston Orlando
4524 Green Point Drive 270 Riverside Parkway
Dallas Suite 106 3550 Brittmoore Road 7608 Currency Drive Suite A
Greensboro, NC 27410 Suite 200 Orlando, FL 32809 Austell, GA 30168
346 E. Belt Line Road Tel: 336-665-1963 Houston, TX. 77043 Tel: 407-856-0660 Tel: 678-838-6000
Suite 600 Fax: 336-665-1965 Tel: 713 329-9551 Fax: 407-856-0090 Fax: 678-838-6001
Coppell, TX 75019 Fax: 713 939-0811
Tel: 972-245-9551
Fax: 972-245-9522

16-1007-03 ©2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. YKK AP America Inc.
270 Riverside Parkway

Suite A
Austell, GA 30168

1-800-955-9551
www.ykkap.com

General Information

YKK AP Anodized Plus® Finish
Limited Warranty and Remedy

YKK AP America Inc. (YKK AP) is pleased to offer a ten (10) year limited warranty on Anodized Plus®
finishes YS1N, YB5N, YB1N, YH3N, YK1N applied to YKK AP products as manufactured by YKK AP
subject to every term, condition and limitation stated herein. YKK AP is also pleased to offer a five (5)
year limited warranty for YKK AP’s white Anodized Plus finish, YW3N, applied to YKK AP products as
manufactured by YKK AP subject to every term, condition and limitation stated herein.

The limited warranty for each Anodized Plus finish starts on the substantial completion date provided
that the materials are fabricated and installed in accordance with YKK AP’s installation instructions. The
substantial completion date should be provided to YKK AP but in no case shall it be later than 6 months
from YKK AP’s date of shipment. If no substantial completion date is provided, YKK AP’s shipping date
shall be used for the effective start date of the limited warranty.

YKK AP warrants that the Anodized Plus finish will not:

A. Peel, crack, flake or blister.

B. 1) Chalk in excess of a numerical rating of 8 when measured in accordance with the standard
procedures defined in ASTM D4214-07, Method D659.

2) Fade or change in color in excess of 5 units (Hunter Color Difference) when measured in
accordance with the standard procedures defined in ASTM D2244-09b, Section 6.3.

3) Change its gloss retention in excess of 50% (percentage retention) when measured in accordance
with standard procedures defined in ASTM D523-08.

This limited warranty applies to YKK AP products installed within continental North America, provided
the installation is in a non-chemical use area and provided the product’s exterior surface is washed with
fresh water at least two (2) times per year. Washes must be recorded in a log book and contain the
date that the products were washed, source of water, company, persons performing the cleaning, AND
how the wash was performed. Washing must begin within six (6) months of product installation and the
log shall be made available upon request. In addition, product installations that are located near coastal
and/or heavy industrial areas must comply with the guidelines for “climatic conditions” aluminum care as
defined in AAMA’s CW-10 publication, Care and Handling of Architectural Aluminum from Shop to Site.

The limited warranty will apply provided YKK AP is notified in writing of the alleged defects within 30
days of the occurrence or appearance of such defect. Upon receipt of the written claim, YKK AP must be
provided access to the product and be given a reasonable opportunity to inspect the material claimed to
be defective.

The sole and exclusive remedy with respect to the above limited warranty, whether such claim is
based on warranty, contract, negligence, strict liability, or any other theory, is limited to the repair or
replacement of such product(s) or, at the option of YKK AP, reimbursed by YKK AP of the purchase price
paid to YKK AP for the particular product(s).

The warranty will not apply to or cover:

A. Products that have been curved, formed, or welded after anodizing.
B. Damage to the coating occasioned by moisture or other contamination detrimental to the coating
because of improper storage of the coated metal prior to installation.
C. Damage to the coated metal caused by handling, shipping processing and/or installation.
D. Fading or color changes on products that are not equally exposed to the sun and elements.

(continued)

Page-10 GI-1000-01 | Effective Date: February 1, 2012

General Information

YKK AP Anodized Plus® Finish
Limited Warranty and Remedy

E. Products installed within chemical use areas that can experience concentrated chemical build-up on
the product’s surfaces such as, but not limited to, pools, laboratories, and chemical storage areas.
F. The warranty will not be applicable to damage or failure which is caused by acts of God, falling
objects, external forces, explosions, fire, riot, civil commotions, acts of war, radiation, or other such
similar or dissimilar occurrences beyond the control of YKK AP.

YKK AP does not make any other representations or warranties, whether oral or written, express
or implied, including but not limited to any warranty regarding merchantability or fitness for
a particular purpose. In no event shall YKK AP be liable for direct, indirect, consequential or
special damages, including but not limited to property damage, lost profits or lost revenue. Buyer
agrees to pass on to all its customers and users in writing at the time of inquiries and orders are
received by Buyer, YKK AP’s limited warranty and remedy set forth above.

The agents, dealers and employees of YKK AP are not authorized to make modifications to this
warranty, or make additional warranties binding on YKK AP. Accordingly, additional statements, whether
oral or written, do not constitute warranties and should not be relied upon.

YKK AP Aluminum Finish Code

CODE DESCRIPTION

YS1N Clear Anodized Plus®
YH3N Champagne Anodized Plus®
YB1N Medium Bronze Anodized Plus®
YB5N Dark Bronze Anodized Plus®
YK1N Black Anodized Plus®
YW3N White Anodized Plus®
M Mill Finish

Anodized Plus® is an advanced sealing technology for anodized aluminum that completely seals the
anodic film yielding superior durability (Refer to AAMA 612 for performance attributes).

Painted Finishes

Building designs may require the use of painted finishes for a variety of color.

The American Architectural Manufacturers Association (AAMA) has developed a set of specifications
to aid specifiers in selecting the proper paint based on the desired application. YKK AP applies painted
finishes to YKK AP’s products in accordance with the following AAMA standards.

AAMA 2603 covers most baked enamel (acrylic / polyester) paint finishes. Common applications for these
finishes are interior applications where color retention is not required. The baked enamel coatings are
harder than the fluoropolymer PVDF (Kynar) coatings. These paints are less expensive, but have poor
resistance to color fading and chalking.

AAMA 2604 covers most 50% fluoropolymer paint finishes. These finishes provide good color and
gloss retention. They also will provide good hardness and abrasion resistance. A paint meeting this
specification is often used in exterior applications where a high level of performance is required.

AAMA 2605 covers most 70% flouropolymer paint finishes. These finishes exhibit superior resistance to
humidity, color change, chalk, gloss loss and chemicals. Paints meeting this specification are often used
in exterior applications where superior performance is required.

Effective Date: February 1, 2012 | GI-1000-01 Page-11