MODBAR-AV

Program Dose Description “Barista” Programming

Group Dose • This parameter allows the operator to • It is possible to set the dose for both
Settings program the amount of coffee (brewing a short and a long shot on the same
Group 1 Dose amount) for each Selection Indicator. Selection Indicator.
Settings
• The brewing amount can be set in terms • PULSE mode: control of doses in volume
of time (sec.), pulses, mass or brewratio. • MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the
• Once programmed, the Selection
Indicator remains lighted. coffee powder and the weight of the
drink

Display Operating Procedure

Press Enter 12 To set the brewing time of a short shot, it will be necessary to activate the tap lever until water flows from the
To Exit group, activate again the tap lever to stop and store the desired dose.

Press b To Stop
10 pulses

G1B1 Saved
10 Pulses

↓ Short Dose 13 Press the button T1 or T2 to view the dose. Pressing the button T3 , the dose value will blink. Use the
60
button T1 or T2 to change the value, press the button T3 to confirm the desired value.

↓ Long 14 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between DOSE,
3 SEC RINSE BACKFLUSH, 3 SEC RINSE and CONTINUOUS, press the T3 button to confirm the option.

51EN

“Barista” Programming Description • It is possible to set the dose for both
Program Dose a short and a long shot on the same
• This parameter allows the operator to Selection Indicator.
Group Dose program the amount of coffee (brewing
Settings amount) for each Selection Indicator. • PULSE mode: control of doses in volume
• MASS mode: control of doses in mass
Group 1 Dose • The brewing amount can be set in terms • BREW RATIO mode: ratio between the
Settings of time (sec.), pulses, mass or brewratio.
coffee powder and the weight of the
• Once programmed, the Selection drink
Indicator remains lighted.

Display Operating Procedure

Group 1 Dose 15 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Barista”
Exit programming.

16 Press T1 or T2 to continue with the programming of the other parameters.

17G1█ MODBAR G2█ Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
espresso machine.
163Puls 0Puls

EN52

(only on ABR espresso machine models) “Barista” Programming

Program Dose Description

Group Dose • This parameter allows the operator to • It is possible to set the dose for both
Settings program the amount of coffee (brewing a short and a long shot on the same
Group 1 Dose amount) for each Selection Indicator. Selection Indicator.
Settings
• The brewing amount can be set in terms • PULSE mode: control of doses in volume
of time (sec.), pulses, mass or brewratio. • MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the
• Once programmed, the Selection
Indicator remains lighted. coffee powder and the weight of the
drink

Display Operating Procedure

G1█ MODBAR G2█ 1 When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming.
163Puls 0Puls After about 5 seconds the following screen is displayed.

Group Dose 2 Move between the parameters using the buttons T1 or T2 until the display shows:
Settings

Group 1 Dose 3 Press the T3 button to start the doses programming procedure.
Settings

G1 Dose Mode 4 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between PULSES,
BREWRATIO MASS and BREWRATIO, press the T3 button to confirm the option.

53EN

“Barista” Programming (only on ABR espresso machine models)

Program Dose Description • It is possible to set the dose for both
a short and a long shot on the same
Group Dose • This parameter allows the operator to Selection Indicator.
Settings program the amount of coffee (brewing
Group 1 Dose amount) for each Selection Indicator. • PULSE mode: control of doses in volume
Settings • MASS mode: control of doses in mass
• The brewing amount can be set in terms • BREW RATIO mode: ratio between the
of time (sec.), pulses, mass or brewratio.
coffee powder and the weight of the
• Once programmed, the Selection drink
Indicator remains lighted.

Display Operating Procedure

G1 ↑ Brew Ratio 5 Press the button T1 or T2 to view the dose of each key. Pressing the button T3 , the dose value will
1:2.00
blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired value.

G1 ↑ Long 6 Press the button T1 or T2 to view the coffee mass of each group. Pressing the button T3 , the value will
Weigh Coffee
blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired value.
G1 ↓ Long
WEIGH PF 7 Press the button T1 or T2 to view the portafilter mass of each group. Pressing the button T3 , the value
will blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired
G1 PF Mass
800.0g value.

54 8 Press the button T1 or T2 to view the portafilter mass of each group. Pressing the button T3 , the value
will blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired
EN
value.

(only on ABR espresso machine models) “Barista” Programming

Program Dose Description

Group Dose • This parameter allows the operator to • It is possible to set the dose for both
Settings program the amount of coffee (brewing a short and a long shot on the same
Group 1 Dose amount) for each Selection Indicator. Selection Indicator.
Settings
• The brewing amount can be set in terms • PULSE mode: control of doses in volume
of time (sec.), pulses, mass or brewratio. • MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the
• Once programmed, the Selection
Indicator remains lighted. coffee powder and the weight of the
drink

Display Operating Procedure

G1 Coffee Mass 9 Press the button T1 or T2 to view the coffee mass of each group. Pressing the button T3 , the value will
14.0g
blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired value.

Exit 10 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Barista”
Group 1 programming.

11 Press T1 or T2 to continue with the programming of the other parameters.

12G1█ MODBAR G2█ Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
espresso machine.
163Puls 0Puls

55 EN

“Barista” Programming (only on ABR espresso machine models)

Scale Configuration Description • The dose can be set by pulses or by
mass (weight).
Group Dose • This parameter allows the operator to
Settings view and manually change each dose for
Scale each Selection Indicator.
Configuration
• For greater accuracy and consistency of
the doses, it is recommended that you
set each Selection Indicator.

Display Operating Procedure

G1█ MODBAR G2█ 1 When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming.
163Puls 0Puls After about 5 seconds the following screen is displayed.

Group Dose 2 Move between the parameters using the buttons T1 or T2 until the display shows:
Settings

Scale 3 Press the T3 button to start the doses programming procedure.
Configuration

Scale Tare Time 4 Press the T3 button to enter the menu, navigate the parameters using the buttons T1 and T2 to set the
3s desired value. This parameter is common to all groups.
EN
56

(only on ABR espresso machine models) “Barista” Programming

Scale Configuration Description

Group Dose • This parameter allows the operator to • The dose can be set by pulses or by
Settings view and manually change each dose for mass (weight).
Scale each Selection Indicator.
Configuration
• For greater accuracy and consistency of
the doses, it is recommended that you
set each Selection Indicator.

Display Operating Procedure

Scale Settings 5 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Barista”
Exit programming.

6 Press T1 or T2 to continue with the programming of the other parameters.

G1█ MODBAR G2█ 7 Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
163Puls 0Puls espresso machine.

57 EN

“Barista” Programming Description 1, while for an espresso machine with 2
Coffee Boiler groups you can also set the coffee boiler
• This parameter allows the operator to 2.
Group Dose program the coffee boiler temperature.
Settings Each group can have a different
programming.
Coffee Boiler
Settings • For an espresso machine composed of 1
group you can only set the coffee boiler

Display Operating Procedure

G1█ MODBAR G2█ 1 When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming.
163Puls 0Puls After about 5 seconds the following screen is displayed.

Group Dose 2 Move between the parameters using the buttons T1 or T2 until the display shows:
Settings

Coffee Boiler 3 Press the T3 button to enter the menu.
Settings

CB1 Temperature 4 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the desired tempera-
94,5°C 95,0°C ture, press the T3 button to confirm the value. The temperature indicated on the left is the actual tem-

EN58 perature of the group while the temperature on the right is the set temperature.

Coffee Boiler Description “Barista” Programming

Group Dose • This parameter allows the operator to • For an espresso machine composed of 1
Settings program the coffee boiler temperature. group you can only set the coffee boiler
Coffee Boiler Each group can have a different 1, while for an espresso machine with 2
Settings programming. groups you can also set the coffee boiler
2.

Display Operating Procedure

CB Settings 5 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Barista”
Exit programming.

6 Press T1 or T2 to continue with the programming of the other parameters.

G1█ MODBAR G2█ 7 Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
163Puls 0Puls espresso machine.

59 EN

“Barista” Programming Description pre-brewing cycle; during this time the
Pre-Infusion or Pre-Brewing pump is active. Once the pre-brewing
• This parameter allows the operator to cycle is over, the normal brewing cycle
Group Dose program the time of pre-brewing of will continue until the end.
Settings water with the coffee. Each group can • For an espresso machine composed of
Pre-Inf have a different programming. two groups, they are identified as Group
Settings 1 and Group 2.
• Pre-brewing has only two values to be
Display adjusted for each group. The time (in
seconds) for which the brewing valve
is open during the pre-brewing cycle
and the time (in seconds) for which
the brewing valve is closed during the

Operating Procedure

G1█ MODBAR G2█ 1 When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming.
163Puls 0Puls After about 5 seconds the following screen is displayed.

Group Dose 2 Move between the parameters using the buttons T1 or T2 until the display shows:
Settings

Pre-Inf 3 Press the T3 button to enter the menu.
Settings

EN Group 1 Pre-Inf Press T1 or T2 to select the group whose parameters you want to set.
2s Wet 0s Hold
4 By pressing the T3 button the first value will blink. Use the buttons T1 and T2 to reach the value
60
that you want to set, press T3 to confirm. Repeat this operation to set the second value.
To set the preinfusion time 2 seconds minimum.

Pre-Infusion or Pre-Brewing Description “Barista” Programming

Group Dose • This parameter allows the operator to brewing cycle will continue until the
Settings program the time of pre-brewing of end.
Pre-Inf water with the coffee. • For an espresso machine composed of
Settings two groups, they are identified as Group
• The time (in seconds) for which the 1 and Group 2.
Display brewing valve is open during the pre-
brewing cycle and the time (in seconds)
for which the brewing valve is closed
during the pre-brewing cycle; during
this time the pump is active. Once the
pre-brewing cycle is over, the normal

Operating Procedure

Pre-Inf 5 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between
WITHOUT PUMP WITHOUT PUMP and WITH PUMP, press the T3 button to confirm the option.

Pre-Inf Settings 6 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Barista”
Exit programming.

7 Press T1 or T2 to continue with the programming of the other parameters.

G1█ MODBAR G2█ 8 Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
163Puls 0Puls espresso machine. 61
EN

“Barista” Programming Description
Keypad LEDs
• This parameter allows the operator to
Group Dose enable/disabled the keypad led.
Settings

Keypad LEDs
ENABLED

Display Operating Procedure

G1█ MODBAR G2█ 1 When the espresso machine is turned on, press and hold the T3 button to access the “Barista” programming.
163Puls 0Puls After about 5 seconds the following screen is displayed.

Group Dose 2 Move between the parameters using the buttons T1 or T2 until the display shows:
Settings

Keypad LEDs 3 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between
ENABLED ENABLED and DISABLED, press the T3 button to confirm the option.

EN 4 Press T1 or T2 to continue with the programming of the other parameters.

62

“Barista” Programming

Keypad LEDs Description

Group Dose • This parameter allows the operator to
Settings enable/disabled the keypad led.
Keypad LEDs
ENABLED

Display Operating Procedure

G1█ MODBAR G2█ 5 Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
163Puls 0Puls espresso machine.

63EN

“Barista” Programming Description
Exit Menu
• This parameter allows the operator to
Group Dose exit the “Barista” programming and
Settings return to the normal use of the espresso
machine.

Exit
Menu

Display Operating Procedure

Exit 1 Press the T3 button to exit the “Barista” programming and return to the normal use of the espresso
Menu machine.

G1█ MODBAR G2█ 2 Alternatively, you can exit the “Barista” programming and return to the normal use of the espresso machine by
163Puls 0Puls pressing T2 and T3 at the same time.

EN64

“Technical” Programming

Language Description

Enter Password • This parameter allows the technician to
change the language of the display.

Language
ENGLISH

Display Operating Procedure

G1█ MODBAR G2█ 1 When the espresso machine is turned on, press and hold the T3 button . After about 10 seconds the
163Puls 0Puls following screen is displayed.

Enter Password 2 Enter the technician password using the buttons T1 ,T2 and T3 . After the acceptance, the following
screen is displayed.

Language 3 Press the T3 button to enter the menu, move between the parameters using the buttons T1 and T2
ENGLISH to select a language , press the T3 button to confirm the option.

4 Press T1 or T2 to continue with the programming of the other parameters.

65 EN

“Technical” Programming Description
Language
• This parameter allows the technician to
Enter Password change the language of the display.

Language
ENGLISH

Display Operating Procedure

Exit 5 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

G1█ MODBAR G2█ 6 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN66

“Technical” Programming

Temperature Measurement Units Description

Enter Password • This parameter allows the technician to
change the temperature display from
degrees Celsius to degrees Fahrenheit
and vice versa.

Temp Units
CELSIUS

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Temp Units 2 Press the T3 button to enter the menu, move between the parameters using the buttons T1 and T2 to
CELSIUS select an option, press the T3 button to confirm the option.

3 Press T1 or T2 to continue with the programming of the other parameters.

Exit 4 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

67 EN

“Technical” Programming

Temperature Measurement Units Description

Enter Password • This parameter allows the technician to
change the temperature display from
degrees Celsius to degrees Fahrenheit
and vice versa.

Temp Units
CELSIUS

Display Operating Procedure

G1█ MODBAR G2█ 5 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN68

Name Description “Technical” Programming

Enter Password • This parameter allows the technician to • The user name is displayed continuously
program a 16 character user name. on the display on the second line.

Name
Modbar

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Name 2 Press the T3 button to enter the menu, use the buttons T1 and T2 to set the desired value, press the
Modbar T3 button to confirm the value and proceed with writing.

3 Press T1 or T2 to continue with the programming of the other parameters.

Exit 4 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

69 EN

“Technical” Programming Description • The user name is displayed continuously
Name on the display on the second line.
• This parameter allows the technician to
Enter Password program a 16 character user name.

Name
Modbar

Display Operating Procedure

G1█ MODBAR G2█ 5 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN70

“Technical” Programming

Number of Groups Description

Enter Password • This parameter allows the technician to
set the number of groups.

Number of Groups
1

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Number of Groups 2 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between 1 and 2,
1 press the T3 button
to confirm the option.

3 Press T1 or T2 to continue with the programming of the other parameters.

Exit 4 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

71 EN

“Technical” Programming Description
Number of Groups
• This parameter allows the technician to
Enter Password set the number of groups.

Number of Groups
1

Display Operating Procedure

G1█ MODBAR G2█ 5 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN72

“Technical” Programming

Program Dose Description

Group Dose • This parameter allows the operator to
Settings cancel all the doses set.
Dose Settings
Reset

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Group Dose 2 Press the T3 button to enter the doses programming procedure.
Settings

Dose Settings 3 Press the button T3 to confirm the procedure
Reset

Resetting 4 Now all settings are cleared.
Doses...

73 EN

“Technical” Programming Description
Program Dose
• This parameter allows the operator to
Group Dose cancel all the doses set.
Settings

Dose Settings
Reset

Display Operating Procedure

Group Dose 5 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical”
Exit programming.

6 Press T1 or T2 to continue with the programming of the other parameters.

G1█ MODBAR G2█ 7 Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
163Puls 0Puls espresso machine.

EN74

Program Dose Description “Technical” Programming

Group Dose • This parameter allows the operator to • It is possible to set the dose for both
Settings program the amount of coffee (brewing a short and a long shot on the same
Group 1 Dose amount) for each Selection Indicator. Selection Indicator.
Settings
• The brewing amount can be set in terms • PULSE mode: control of doses in volume
of time (sec.), pulses, mass or brewratio. • MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the
• Once programmed, the Selection
Indicator remains lighted. coffee powder and the weight of the
drink

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Group Dose 2 Move between the parameters using the buttons T1 or T2 until the display shows:
Settings

Group 1 Dose 3 Press the T3 button to start the doses programming procedure.
Settings

G1 Dose Mode 4 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between PULSES,
DOSE MASS and BREWRATIO, press the T3 button to confirm the option.

75EN

“Technical” Programming Description • It is possible to set the dose for both
Program Dose a short and a long shot on the same
• This parameter allows the operator to Selection Indicator.
Group Dose program the amount of coffee (brewing
Settings amount) for each Selection Indicator. • PULSE mode: control of doses in volume
• MASS mode: control of doses in mass
Group 1 Dose • The brewing amount can be set in terms • BREW RATIO mode: ratio between the
Settings of time (sec.), pulses, mass or brewratio.
coffee powder and the weight of the
• Once programmed, the Selection drink
Indicator remains lighted.

Display Operating Procedure

↑ Short 5 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between DOSE,
DOSE BACKFLUSH, 3 SEC RINSE and CONTINUOUS, press the T3 button to confirm the option.

↑ Short Program 6 Press the T3 button to start the doses programming procedure.
Volume Dose

Press Enter 7 To set the brewing time of a short shot, it will be necessary to activate the tap lever until water flows from the
To Exit group, activate again the tap lever to stop and store the desired dose.

Press b To Stop
10 pulses

G1B1 Saved
10 Pulses

EN76

Program Dose Description “Technical” Programming

Group Dose • This parameter allows the operator to • It is possible to set the dose for both
Settings program the amount of coffee (brewing a short and a long shot on the same
Group 1 Dose amount) for each Selection Indicator. Selection Indicator.
Settings
• The brewing amount can be set in terms • PULSE mode: control of doses in volume
of time (sec.), pulses, mass or brewratio. • MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the
• Once programmed, the Selection
Indicator remains lighted. coffee powder and the weight of the
drink

Display Operating Procedure

↑ Short Dose 8 Press the button T1 or T2 to view the dose. Pressing the button T3 , the dose value will blink. Use the
30
button T1 or T2 to change the value, press the button T3 to confirm the desired value.

↑ Long 9 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between DOSE,
BACKFLUSH BACKFLUSH, 3 SEC RINSE and CONTINUOUS, press the T3 button to confirm the option.

↓ Short 10 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between DOSE,
DOSE BACKFLUSH, 3 SEC RINSE and CONTINUOUS, press the T3 button to confirm the option.

↓ Short Program 11 Press the T3 button to start the doses programming procedure.
Volume Dose

77 EN

“Technical” Programming Description • It is possible to set the dose for both
Program Dose a short and a long shot on the same
• This parameter allows the operator to Selection Indicator.
Group Dose program the amount of coffee (brewing
Settings amount) for each Selection Indicator. • PULSE mode: control of doses in volume
• MASS mode: control of doses in mass
Group 1 Dose • The brewing amount can be set in terms • BREW RATIO mode: ratio between the
Settings of time (sec.), pulses, mass or brewratio.
coffee powder and the weight of the
• Once programmed, the Selection drink
Indicator remains lighted.

Display Operating Procedure

Press Enter 12 To set the brewing time of a short shot, it will be necessary to activate the tap lever until water flows from the
To Exit group, activate again the tap lever to stop and store the desired dose.

Press b To Stop
10 pulses

G1B1 Saved
10 Pulses

↓ Short Dose 13 Press the button T1 or T2 to view the dose. Pressing the button T3 , the dose value will blink. Use the
60
button T1 or T2 to change the value, press the button T3 to confirm the desired value.

EN ↓ Long 14 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between DOSE,
3 SEC RINSE BACKFLUSH, 3 SEC RINSE and CONTINUOUS, press the T3 button to confirm the option.

78

Program Dose Description “Technical” Programming

Group Dose • This parameter allows the operator to • It is possible to set the dose for both
Settings program the amount of coffee (brewing a short and a long shot on the same
Group 1 Dose amount) for each Selection Indicator. Selection Indicator.
Settings
• The brewing amount can be set in terms • PULSE mode: control of doses in volume
of time (sec.), pulses, mass or brewratio. • MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the
• Once programmed, the Selection
Indicator remains lighted. coffee powder and the weight of the
drink

Display Operating Procedure

Group 1 Dose 15 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical”
Exit programming.

16 Press T1 or T2 to continue with the programming of the other parameters.

17G1█ MODBAR G2█ Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
espresso machine.
163Puls 0Puls

79 EN

“Technical” Programming (only on ABR espresso machine models)

Program Dose Description • It is possible to set the dose for both
a short and a long shot on the same
Group Dose • This parameter allows the operator to Selection Indicator.
Settings program the amount of coffee (brewing
Group 1 Dose amount) for each Selection Indicator. • PULSE mode: control of doses in volume
Settings • MASS mode: control of doses in mass
• The brewing amount can be set in terms • BREW RATIO mode: ratio between the
of time (sec.), pulses, mass or brewratio.
coffee powder and the weight of the
• Once programmed, the Selection drink
Indicator remains lighted.

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Group Dose 2 Move between the parameters using the buttons T1 or T2 until the display shows:
Settings

Group 1 Dose 3 Press the T3 button to start the doses programming procedure.
Settings

EN G1 Dose Mode 4 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between PULSES,
DOSE MASS and BREWRATIO, press the T3 button to confirm the option.

80

(only on ABR espresso machine models) “Technical” Programming

Program Dose Description

Group Dose • This parameter allows the operator to • It is possible to set the dose for both
Settings program the amount of coffee (brewing a short and a long shot on the same
Group 1 Dose amount) for each Selection Indicator. Selection Indicator.
Settings
• The brewing amount can be set in terms • PULSE mode: control of doses in volume
of time (sec.), pulses, mass or brewratio. • MASS mode: control of doses in mass
• BREW RATIO mode: ratio between the
• Once programmed, the Selection
Indicator remains lighted. coffee powder and the weight of the
drink

Display Operating Procedure

G1 ↑ Brew Ratio 4 Press the button T1 or T2 to view the dose of each key. Pressing the button T3 , the dose value will
1:2.00
blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired value.

G1 ↑ Long 5 Press the button T1 or T2 to view the coffee mass of each group. Pressing the button T3 , the value will
Weigh Coffee
blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired value.
G1 ↓ Long
WEIGH PF 6 Press the button T1 or T2 to view the portafilter mass of each group. Pressing the button T3 , the value
will blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired
G1 PF Mass
800.0g value.

7 Press the button T1 or T2 to view the portafilter mass of each group. Pressing the button T3 , the value
will blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired
EN
value.

81

“Technical” Programming (only on ABR espresso machine models)

Program Dose Description • It is possible to set the dose for both
a short and a long shot on the same
Group Dose • This parameter allows the operator to Selection Indicator.
Settings program the amount of coffee (brewing
Group 1 Dose amount) for each Selection Indicator. • PULSE mode: control of doses in volume
Settings • MASS mode: control of doses in mass
• The brewing amount can be set in terms • BREW RATIO mode: ratio between the
of time (sec.), pulses, mass or brewratio.
coffee powder and the weight of the
• Once programmed, the Selection drink
Indicator remains lighted.

Display Operating Procedure

G1 Coffee Mass 8 Press the button T1 or T2 to view the coffee mass of each group. Pressing the button T3 , the value will
14.0g
blink. Use the button T1 or T2 to change the value, press the button T3 to confirm the desired value.

Exit 9 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Barista”
Group 1 programming.

10 Press T1 or T2 to continue with the programming of the other parameters.

11G1█ MODBAR G2█ Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
espresso machine.
163Puls 0Puls

EN82

(only on ABR espresso machine models) “Technical” Programming

Scale Configuration Description

Enter Password • This parameter allows the operator to • This parameter enables the technician
view and manually change each dose for to set some scale parameters like:
Scale each Selection Indicator.
Configuration - Enabling/disabling the offset
• For greater accuracy and consistency of parameter;
the doses, it is recommended that you
set each Selection Indicator. - Setting the weight reading time;
- Calibrating the scales;
• The dose can be set by pulses or by - Updating the scale software.
mass (weight).

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Scale 2 Press the T3 button to start the doses programming procedure.
Configuration

Auto Offset 3 Press the T3 button to enter the menu, move between the parameters using the buttons T1 and T2
ENABLED to select ENABLED or DISABLED, press the T3 button to confirm the option.

Scale Tare Time 4 Press the T3 button to enter the menu, navigate the parameters using the buttons T1 and T2 to set the
3s desired value. This parameter is common to all groups.

83 EN

“Technical” Programming (only on ABR espresso machine models)

Scale Configuration Description • This parameter enables the technician
to set some scale parameters like:
Enter Password • This parameter allows the operator to
view and manually change each dose for - Enabling/disabling the offset
Scale each Selection Indicator. parameter;
Configuration
• For greater accuracy and consistency of - Setting the weight reading time;
the doses, it is recommended that you - Calibrating the scales;
set each Selection Indicator. - Updating the scale software.

• The dose can be set by pulses or by
mass (weight).

Display Operating Procedure

G1 Scale 5 This parameter indicates that the scale is properly connected; navigate using the T1 and T2 buttons to
PRESENT display the next menu.

Calibrate 6 Press the T3 button to start the calibration procedure.
G1 Scale

Empty G1 Scale Remove any object from the scale, then press the T3 button to confirm.
And Press Enter
7 Place the reference weights onto the scale, then press the T3 button to confirm. At the end of the process,
Place 100g on G1 the self-calibration values or a confirmation message are displayed.
And Press Enter
Repeat this operation for each group.

G1 Scale: v2.5.2 8 Press T2 to proceed with setting and press the T3 button to update the scale firmware if necessary.
Upgrade to 2.5.2

EN84

(only on ABR espresso machine models) “Technical” Programming

Scale Configuration Description

Enter Password • This parameter allows the operator to • This parameter enables the technician
view and manually change each dose for to set some scale parameters like:
Scale each Selection Indicator.
Configuration - Enabling/disabling the offset
• For greater accuracy and consistency of parameter;
the doses, it is recommended that you
set each Selection Indicator. - Setting the weight reading time;
- Calibrating the scales;
• The dose can be set by pulses or by - Updating the scale software.
mass (weight).

Display Operating Procedure

View Scale 9 Press the T3 button to enter the menu.
Versions

G1 Scale 10 Use T1 and T2 to display the hardware and software version installed.
HW3.0 FW2.5.2

View Versions 11 Press the T3 button to exit the submenu
Exit

Scale Settings 12 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical”
Exit programming. 85

EN

“Technical” Programming (only on ABR espresso machine models)

Scale Configuration Description • This parameter enables the technician
to set some scale parameters like:
Enter Password • This parameter allows the operator to
view and manually change each dose for - Enabling/disabling the offset
Scale each Selection Indicator. parameter;
Configuration
• For greater accuracy and consistency of - Setting the weight reading time;
the doses, it is recommended that you - Calibrating the scales;
set each Selection Indicator. - Updating the scale software.

• The dose can be set by pulses or by
mass (weight).

Display Operating Procedure

13 Press T1 or T2 to continue with the programming of the other parameters.

14G1█ MODBAR G2█ Press T2 and T3 at the same time to exit the programming mode and return to the normal use of the
espresso machine.
163Puls 0Puls

EN86

Coffee Boiler Description “Technical” Programming

Enter Password • This parameter enables the technician though the temperature of the boiler
to set various parameters of the coffee may vary slightly, the temperature of the
Coffee Boiler boiler. water exiting the group is constant.
Settings • To properly calibrate the temperature
• The temperature of the boiler is of any espresso machine it is import to
measured at the most critical point in measure the temperature of the water
the boiler where temperature fluctuation exiting the group by means of an external
is the greatest. temperature measuring device. The
difference of the display temperature
• The temperature of the water exiting the and the measured temperature may be
group head is held constant by means compensated by use of the “Coffee T.
of the mass of the group casting. Even Offset” parameter.

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Coffee Boiler 2 Press the T3 button to enter the menu.
Settings
Press the T3 button to enter the menu, move between the parameters using the buttons T1 and T2
CB1 Enabled
ENABLED 3 to select ENABLED or DISABLED, press the T3 button to confirm the option. In the case of option enabled

you can set the following parameters.

CB1 Temperature 4 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the desired tempera-
93.0°C 94,5 °C ture, press the T3 button to confirm the value. The temperature indicated on the left is the actual tem-

perature of the group while the temperature on the right is the set temperature.

DANGER 87 EN

THE COFFEE BOILER CONTAINS WATER AT ELEVATED TEMPERATURES.
WATER TEMPERATURE OVER 52°c CAN CAUSE SEVERE BURNS IN STANTLY OR DEATH FROM SCALDING.

“Technical” Programming Description
Coffee Boiler
• The OFFSET parameter is used to
Enter Password calibrate the coffee boiler temperature can cause unexpected results.
system to ensure the display temperature • I t is important to write down this value
Coffee Boiler accurately represents the temperature
Settings of the water exiting the group head. before making changes to be sure you
can return to the factory programming if
• This parameter is preset at the factory unexpected results occur. Each machine
based upon initial tests of this espresso may have a different value as it is set
machine. individually.

Display • I t is not recommended that this number
is changed. Changes to this parameter

Operating Procedure

Out Offset 5 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the desired tempera-
- 1 °C ture, press the T3 button to confirm the value.

CB Settings 6 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical”
Exit programming.

Exit 7 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

G1█ MODBAR G2█ 8 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN88

“Technical” Programming

Head Heater Description

Enter Password • This parameter enables the technician
to set various parameters of the
Head Heater Espresso Tap for increasing temperature
Settings performances depending on machine
configuration.

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

Head Heater until the following screen is displayed.
Settings
2 Press the T3 button to enter the menu.

Head 1 Smart PID 3 Press the T3 button to enter the menu.
Settings

Head1 STO0 4 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the desired tempera-
2 °C ture, press the T3 button to confirm the value.

DANGER 89 EN

THE COFFEE BOILER CONTAINS WATER AT ELEVATED TEMPERATURES.
WATER TEMPERATURE OVER 52°c CAN CAUSE SEVERE BURNS IN STANTLY OR DEATH FROM SCALDING.

“Technical” Programming Description
Head Heater
• This parameter enables the technician
Enter Password to set various parameters of the
Espresso Tap for increasing temperature
Head Heater performances depending on machine
Settings configuration.

Display Operating Procedure

Head1 STO1 5 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the desired tempera-
0 °C ture, press the T3 button to confirm the value.

Head1 STO2 6 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the desired tempera-
4 °C ture, press the T3 button to confirm the value.

Head1 SMO1 7 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the value, press the
120 T3 button to confirm the value.

Head1 SMO2 8 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the value, press the
240 T3 button to confirm the value.
EN
90

“Technical” Programming

Head Heater Description

Enter Password • This parameter enables the technician
to set various parameters of the
Head Heater Espresso Tap for increasing temperature
Settings performances depending on machine
configuration.

Display Operating Procedure

Head1 MST 9 Press the T3 button to enter the menu, move with the buttons T1 and T2 to set the value, press the
6 T3 button to confirm the value.

10Head 1 Smart PID Press T1 or T2 until the display shows the exit menu, press the T3 button to exit the menu.
Exit

Head Heater 11 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical”
Exit programming.

Exit 12 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

91 EN

“Technical” Programming Description
Head Heater
• This parameter enables the technician
Enter Password to set various parameters of the
Espresso Tap for increasing temperature
Head Heater performances depending on machine
Settings configuration.

Display Operating Procedure

13G1█ MODBAR G2█ Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
by pressing T2 and T3 at the same time.
163Puls 0Puls

EN92

Pre-Infusion or Pre-Brewing Description “Technical” Programming

Enter Password • This parameter allows the operator to pre-brewing cycle; during this time the
program the time of pre-brewing of pump is active. Once the pre-brewing
Pre-Inf water with the coffee. Each group can cycle is over, the normal brewing cycle
Settings have a different programming. will continue until the end.
• For an espresso machine composed of
• Pre-brewing has only two values to be two groups, they are identified as Group
adjusted for each group. The time (in 1 and Group 2.
seconds) for which the brewing valve
Display is open during the pre-brewing cycle
and the time (in seconds) for which
the brewing valve is closed during the

Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Pre-Inf 2 Press the T3 button to enter the menu.
Settings

Pre-Inf 3 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between
ENABLED ENABLED and DISABLED, press the T3 button to confirm the option.

Group 1 Pre-Inf Press T1 or T2 to select the group whose parameters you want to set.
2s Wet 0s Hold
4 By pressing the T3 button the first value will blink. Use the buttons T1 and T2 to reach the value
EN
that you want to set, press T3 to confirm. Repeat this operation to set the second value.
To set the preinfusion time 2 seconds minimum.

93

“Technical” Programming Description
Pre-Infusion or Pre-Brewing
• This parameter allows the operator to
Enter Password program the time of pre-brewing of pre-brewing cycle; during this time the
water with the coffee. Each group can pump is active. Once the pre-brewing
Pre-Inf have a different programming. cycle is over, the normal brewing cycle
Settings will continue until the end.
• Pre-brewing has only two values to be • For an espresso machine composed of
adjusted for each group. The time (in two groups, they are identified as Group
seconds) for which the brewing valve 1 and Group 2.
is open during the pre-brewing cycle
Display and the time (in seconds) for which
the brewing valve is closed during the

Operating Procedure

Pre-Inf 5 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between
WITHOUT PUMP WITHOUT PUMP and WITH PUMP, press the T3 button to confirm the option.

Pre-Inf Settings 6 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical”
Exit programming.

Exit 7 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

G1█ MODBAR G2█ 8 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN94

Clock Adjust Description “Technical” Programming

Enter Password • T his parameter allows the user to set the • T here are 4 changeable values within
time of day and the day of the week. this parameter:
Clock Time
00:00 SUNDAY • This parameter is used to display time • Hour;
and is also used by the “Auto On/Off” • Minute;
parameter • Day of week;
• Hour Format 12h or 24h.

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Clock Time 2 Pressing the T3 button the first value will blink. Use the buttons T1 and T2 to set the clock. Repeat
00:00 SUNDAY the operation to set the day of the week.

Exit 3 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

G1█ MODBAR G2█ 4 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

95 EN

“Technical” Programming Description
Keypad LEDs
• This parameter allows the operator to
Enter Password enable/disabled the keypad led.

Keypad LEDs
ENABLED

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Keypad LEDs 2 Press the T3 button to access the menu, then navigate using T1 and T2 to choose between
ENABLED ENABLED and DISABLED, press the T3 button to confirm the option.

Exit 3 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

G1█ MODBAR G2█ 4 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN96

Auto On/Off Description “Technical” Programming

Enter Password • This parameter allows the technician to • This feature also allows the espresso
program the espresso machine to turn on machine to remain in the off condition
at a preset time and turn off at a preset for one repeating closed day.
time.

Auto On/Off
Settings

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Auto On/Off 2 Press the T3 button to enter the menu.
Settings

Auto On/Off 3 Press the T3 button to enter the menu, move between the parameters using the buttons T1 and T2 to
ENABLED select ENABLED or DISABLED , press the T3 button to confirm the option.

Auto On Time If the parameter is enabled, press the T3 button to enter the menu, move with the buttons T1 and T2
00:00
4 to set the desired time, press the T3 button to confirm the value. to set the desired time, EN
Auto Off Time
00:00 Press the T3 button to enter the menu, move with the buttons T1 and T2
press the T3 button to confirm the value.

97

“Technical” Programming Description • This feature also allows the espresso
Auto On/Off machine to remain in the off condition
• T his parameter allows the technician to for one repeating closed day.
Enter Password program the espresso machine to turn on
at a preset time and turn off at a preset
time.

Auto On/Off
Settings

Display Operating Procedure

Closed On 5 Press the T3 button to enter the menu, move with the buttons T1 and T2 to select an option, press
NEVER the T3 button to confirm the option.

Auto On/Off 6 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical”
Exit programming.

Exit 7 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

G1█ MODBAR G2█ 8 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN98

Eco Mode Description “Technical” Programming

Enter Password • This parameter allows the technician to • It is possible to set this parameter also
set up a temperature to be maintained during the normal operation of the
in case of a temporary non utilization of machine by pressing T1 and T2 at the
the espresso machine. same time.

Eco Mode
Settings

Display Operating Procedure

Enter Password 1 After accessing the “Technical” programming menu and entering the password, use the buttons T1 and T2

until the following screen is displayed.

Eco Mode 2 Press the T3 button to enter the menu.
Settings

Eco Mode Temp 3 Press the T3 button to enter the menu, move between the parameters with the buttons T1 and T2 to
-10.0°C set the desired temperature, press the T3 button to confirm the value.

Auto Eco Time 4 Press the T3 button to enter the menu, move between the parameters with the buttons T1 and T2 to
30 set the desired time (in minutes), press the T3 button to confirm the value. A value of “0” (zero) disables

the Eco Mode parameter. EN

99

“Technical” Programming Description • It is possible to set this parameter also
Eco Mode during the normal operation of the
• This parameter allows the technician to machine by pressing T1 and T2 at the
Enter Password set up a temperature to be maintained same time.
in case of a temporary non utilization of
the espresso machine.

Eco Mode
Settings

Display Operating Procedure

Eco Mode 5 Press T1 or T2 until the display shows the exit menu, press the T3 button to return to the “Technical”
Exit programming.

Exit 6 To exit the menu move between the parameters using the buttons T1 and T2 until the exit menu is
Menu displayed. Press the T3 button to exit the menu and return to the normal use of the espresso machine.

G1█ MODBAR G2█ 7 Alternatively, you can exit the “Technical” programming and return to the normal use of the espresso machine
163Puls 0Puls by pressing T2 and T3 at the same time.

EN100