Autodesk CertifiedProfessional in Revitfor Electrical DesignVersion: Demo[ Total Questions: 10]Web: www.certsout.comEmail: [email protected]_ELEC_01101
IMPORTANT NOTICEFeedbackWe have developed quality product and state-of-art service to ensure our customers interest. If you have any suggestions, please feel free to contact us at [email protected] you have any questions about our product, please provide the following items:exam codescreenshot of the questionlogin id/emailplease contact us at [email protected] and our technical experts will provide support within 24 hours.CopyrightThe product of each order has its own encryption code, so you should use it independently. Any unauthorized changes will inflict legal punishment. We reserve the right of final explanation for this statement.
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 1 of 17A. B. C. D. Category BreakdownCategory Number of QuestionsFamilies, Connectors, and Parameters 5Lighting and Switch Systems 2Electrical Systems and Circuiting 2Conduit and Cable Tray Modeling 1TOTAL 10Question #:1 - [Families, Connectors, and Parameters]Refer to exhibit.An electrical designer is reviewing the Type Properties for a floor plan view. How will the view behove when creating a new floor plan?The Electrical Plan view template will be assigned to a new floor plan view created with the Floor Plan tool with the Floor Plan type selectedCreating a new floor plan view using the Floor Plan tool with the Floor Plan type selected will create a new Electrical Plan view template.When duplicating a floor plan view of any type, the Electrical Plan view template will be assigned to the new floor plan view.A new floor plan view created by duplicating a floor plan view of the Floor Plan type will be duplicated as a dependent view.Answer: AExplanationThe exhibit shown displays the Type Properties dialog box for a System Family: Floor Plan view type. Within the “Identity Data” group, there are two critical parameters that govern the behavior of new views created from this view type:“View Template applied to new views”
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 2 of 17A. B. C. “New views are dependent on template”According to Autodesk Revit’s documentation in the Revit MEP User’s Guide (Chapter 48 “Views and View Templates” and Chapter 49 “Preparing Construction Documents”):“When a view template is assigned to a view type through the Type Properties dialog, any new view created from that view type automatically receives the defined view template. This ensures consistent visibility, graphics, and discipline settings for all new views.”In this image, the parameter “View Template applied to new views” is set to Electrical Plan, and “New views are dependent on template” is checked. This means that any new floor plan created using this type will automatically have the Electrical Plan template applied, and the view will be dependent on that template, meaning it inherits all its visibility and annotation control settings.This ensures that all electrical floor plan views generated are standardized and visually consistent, a fundamental practice in Revit Electrical Design workflows, as described in the Smithsonian Facilities Revit Template User’s Guide:“Assigning a default view template to a view type (e.g., Electrical Plan) ensures every new view created follows organizational and graphical standards without manual setup.”Option A matches this behavior exactly.Option B is incorrect** because Revit does not create a new template automatically.Option C is incorrect** because duplication of an existing view does not reassign templates by type.Option D is incorrect** because dependent view creation requires a specific “Duplicate as Dependent” command, not this setting.References:Autodesk Revit MEP User’s Guide – Chapter 48 “Views and View Templates,” pp. 1112–1115Smithsonian Facilities Revit Template User’s Guide – Section 2.8.1 “View Types and View Templates,” p. 30Autodesk Revit Electrical Design Essentials – View Template Application and Management SectionQuestion #:2 - [Lighting and Switch Systems]An electrical designer has noticed lighting fixtures present in an architectural linked model. Which tool should be used to place an instance of those fixtures in the current electrical model while maintaining the position from the architectural model?Copy/MonitorCoordination ReviewReconcile Hosting
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 3 of 17D. Reload LatestAnswer: AExplanationWhen lighting fixtures placed in an architectural linked model need to be replicated in the electrical modelwhile maintaining their exact positions, the correct tool is Copy/Monitor.This Revit feature allows the electrical designer to copy elements—like lighting fixtures—from a linked model into their project, while establishing a monitoring relationship between the original (architectural) and copied (electrical) instances.From the Autodesk Revit MEP User’s Guide – Chapter 55 “Multi-Discipline Coordination” (pages 1349–1357):“Use the Copy/Monitor tool to copy MEP fixtures from an architectural model into an MEP project, and monitor them for changes.”(Revit MEP User’s Guide, p. 1350)“To copy fixtures from a linked model:Click Collaborate tab # Coordinate panel # Copy/Monitor # Select Link.Select the linked architectural model in the drawing area.Click Copy and select the lighting fixtures to copy.Click Finish.Revit MEP copies the fixtures to the current project and establishes monitoring relationships.”*(Revit MEP User’s Guide, p. 1356)Behavior and Benefits:The copied lighting fixtures maintain the same location, orientation, and type mapping as in the linked model.Any changes (move, delete, or modify) made by the architect in the linked model will trigger a coordination review in the electrical model.This ensures accurate positioning and easy coordination between disciplines.“When you select a copied fixture in the current project, the monitor icon displays next to the fixture, indicating that it has a relationship with the original fixture in the linked model.”(Revit MEP User’s Guide, p. 1357)“If copied fixtures are moved, changed, or deleted in the linked model, Revit MEP notifies the engineers of the changes during Coordination Review.”
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 4 of 17A. B. C. D. A. B. C. D. (Revit MEP User’s Guide, p. 1357)Question #:3 - [Families, Connectors, and Parameters]An electrical designer wants to schedule parameters from generic annotations Which type of schedule must be created?A Generic Family scheduleA Generic Annotation scheduleA Note BlockD. A Sheet ListAnswer: CExplanationWhen an electrical designer wants to schedule parameters from Generic Annotations, the correct method is to use a Note Block, not a generic schedule. Revit documentation defines this process clearly under Annotation Schedules (Note Blocks):“Annotation schedules, or note blocks, list all instances of annotations that you can add using the Symbol tool.”“Creating an Annotation Schedule (Note Block):Load the generic annotation family or families into your project and place them where desired.Click View tab # Create panel # Schedules drop-down # Note Block.In the New Note Block dialog, for Family, select a generic annotation.”This extract confirms that when working with generic annotation families, Revit requires the use of a Note Block to extract and list their parameters in a schedule. Standard schedules such as Generic Model or Family schedules cannot access data from Generic Annotations since they are annotation-based, not model-based.Question #:4 - [Electrical Systems and Circuiting]How can an electrical designer see changes from other users without saving their own work to the central model?Relinquish All MineReload LatestManage Worksets
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 5 of 17D. Worksharing DisplayAnswer: BExplanationIn Autodesk Revit, particularly for electrical and MEP design disciplines using a workshared model, the command “Reload Latest” allows a designer to see changes made by other users without saving or publishing their own work to the central model. This tool ensures that while the designer continues to work locally, their environment stays updated with the latest modifications made by colleagues.According to the Autodesk Revit MEP User Guide (Chapter 54 – Working in a Team), under the section Loading Updates from the Central Model, it states:“As you work, you can see the changes other team members have made to the project after they have been synchronized with the central model. You can load updates from the central model without publishing your changes to the central model.In your local file, click Collaborate tab # Synchronize panel # (Reload Latest).”This confirms that the Reload Latest command refreshes your local file with any modifications from the central file that others have synchronized, but it does not send your local changes back. It is a critical feature for coordination in a team environment, especially when multiple designers—such as electrical, mechanical, and structural engineers—are contributing simultaneously to a shared BIM model.By contrast:A. Relinquish All Mine only releases ownership of elements but doesn’t update the local model.C. Manage Worksets is for controlling visibility and editability of worksets.D. Worksharing Display visually identifies ownership and status but doesn’t refresh model data.Therefore, when an electrical designer needs to review updates from others (for example, when a lighting layout needs coordination with architectural ceiling adjustments), the proper workflow is to use Reload Latest, ensuring all new information from the central model appears instantly without saving or affecting their current unsaved edits.References:Autodesk Revit MEP 2011 User’s Guide, Chapter 54: Working in a Team, “Loading Updates from the Central Model,” pp. 1332–1333.Autodesk Revit Structure User’s Guide, Chapter 49: Working in a Team, “Loading Updates from the Central Model,” p. 1230.Smithsonian Revit Template Guide (2021), Section 6.3.1 How Worksharing Works, confirming synchronization and reloading behavior for shared Revit environments.
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 6 of 17A. B. C. D. Question #:5 - [Conduit and Cable Tray Modeling]Refer to the exhibit.An electrical designer models a cable tray in a project and decides to check the box (or Use Annot. Scale tor Single Line Fittings and change the Cable Tray Fitting Annotation Size to 1/8\" (3 mm).What is the result?(The image is presented m Imperial units: 1 In = 25 mm (Metric units rounded].)All cable tray fittings in the project are changed per the new settings.All cable tray fittings in the project change per the new settings when a views detail level is set to Fine.New cable tray fittings use the new settings in views set to 1/8\" (3 mm) scale.New cable tray fittings use the new settings after the change.Answer: AExplanationIn Autodesk Revit MEP, the Electrical Settings dialog box contains project-wide configuration parameters that affect all electrical systems, including Cable Tray Settings. This dialog allows users to control annotation scales, fitting symbols, and text size for documentation purposes.The option labeled “Use Annot. Scale for Single Line Fittings” determines whether the cable tray fittings’ annotation graphics automatically scale according to the view’s annotation scale. When this box is checked, the annotation symbol size for fittings adjusts proportionally to the scale of the view.Similarly, “Cable Tray Fitting Annotation Size” defines the annotation size for cable tray fittings in singleline representations (schematic views or simplified plan representations). Changing this parameter (for instance, from ¾” to #”) modifies the visual representation globally for all cable tray fittings in the project, since the Electrical Settings dialog is a project-wide configuration, not a per-instance or per-view override.According to the Autodesk Revit MEP User’s Guide (Electrical Systems – Cable Trays):“Electrical settings define how cable trays and conduit are displayed throughout the project. Any change made to these settings, such as annotation size or use of annotation scaling, affects all related fittings and components in the project model.”
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 7 of 17A. B. C. D. Therefore, once the designer checks the box for Use Annot. Scale for Single Line Fittings and changes the Cable Tray Fitting Annotation Size to 1/8” (3 mm), all cable tray fittings across the entire project will update to reflect these new settings.Question #:6 - [Families, Connectors, and Parameters]Refer to exhibit.An electrical designer tries to place a generic annotation family in a data device family. The designer receives the error message as shown. What should the designer do?Change the Detail Level to Coarse.Edit the generic annotation family and set it to Shared.Set the view to the Ref. Level.Select the Maintain Annotation Orientation parameter checkboxAnswer: BExplanationThe warning message — “Can’t create this kind of element in this view in the current mode” — appears when an electrical designer attempts to place a Generic Annotation family inside a model family (e.g., a data device or electrical fixture) that is not configured to host annotation elements.According to the Revit Electrical Design documentation, Generic Annotation families are 2D annotation elements, and therefore, cannot be created or viewed in 3D model views unless configured as “Shared.” The official guide clarifies:“You can create generic annotation families and nest them inside host model families so that the annotations display in the project.”However, this only functions correctly if the annotation is enabled to act independently within the host:“To allow a nested annotation to be visible and editable when placed in a host model family, the nested annotation must be set to Shared before loading it into the host.”If the nested annotation is not set to Shared, Revit cannot create or display it in the host’s model view, triggering this exact warning.Thus, the correct workflow is:
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 8 of 17Open the Generic Annotation family in the Family Editor.Go to Family Category and Parameters.Check the box “Shared” under Family Parameters.Save and reload the family into the host electrical device family.Other options—changing view level, detail level, or annotation orientation—do not resolve this placement restriction.Question #:7 - [Families, Connectors, and Parameters]An electrical designer receives an architectural model and links it into the electrical model.The designer wants to use the Copy/Monitor tool to copy the exact electrical fixtures created by the architect.The designer also wants the software to automatically detect new electrical fixtures added to the architectural model.Select the correct coordination settings from the drop-down listsAnswer:
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 9 of 17ExplanationWhen working on linked architectural and electrical Revit models, the Copy/Monitor tool enables electrical designers to copy selected elements (such as lighting or electrical fixtures) from the architectural model into their electrical model. This workflow ensures that any subsequent modifications to these elements in the architectural file are automatically detected and flagged for coordination review.According to the Revit MEP User’s Guide (Chapter 46 “Copy/Monitor and Coordination Review”):
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 10 of 17“Use Copy/Monitor to copy elements from a linked model so that changes to the original elements are tracked. When copying multiple similar elements, select Allow batch copy to automatically copy all instances of that category.”The Coordination Settings dialog provides two primary behavioral controls for each category (such as Electrical Fixtures):1## Copy BehaviorAllow batch copy: Automatically copies all elements of the selected category from the linked architectural model to the host electrical model.This option is ideal for electrical fixtures because it ensures all instances are copied efficiently without manual selection and allows future synchronization.2## Mapping BehaviorCopy original: Creates an exact duplicate of the architectural family in the electrical model without substituting family types or parameters.This ensures full fidelity with the architect’s fixtures and enables Revit to automatically detect newly added or modified elements in the linked model for coordination review.The Smithsonian Facilities Revit Template User’s Guide also confirms this workflow:“Set Copy Behavior to Allow batch copy and Mapping Behavior to Copy original when monitoring shared architectural elements like lighting fixtures, ensuring accurate duplication and automatic update tracking.”These settings allow Revit to issue coordination warnings such as “Instance of link needs Coordination Review” whenever the architectural model is updated, maintaining synchronization across disciplines.References:Autodesk Revit MEP User’s Guide – Chapter 46 “Copy/Monitor and Coordination Review,” pp. 1084–1090Smithsonian Facilities Revit Template User’s Guide – Section 3.4 “Coordination and Copy/Monitor Setup,” p. 87Autodesk Revit Electrical Design Essentials – “Linking Architectural Models and Synchronizing Electrical Fixtures”Question #:8 - [Families, Connectors, and Parameters]Refer to exhibit.
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 11 of 17An electrical designer wants to organize the Protect Browser as shown in the exhibit. Select the correct options in order to achieve the desired organization. (Select three.)Answer:
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 12 of 17Explanation
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 13 of 17C:\\Users\\Waqas Shahid\\Desktop\\Mudassir\\Untitled.jpgIn Autodesk Revit Electrical Design, the Project Browser can be customized to organize views according to disciplines, levels, and view types using the Browser Organization Properties dialog box. This feature allows electrical designers to create structured view hierarchies that align with project standards and simplify navigation — especially in multidisciplinary projects.According to the Revit MEP User’s Guide (Chapter 41 “Browser Organization and View Management”):“Browser organization defines how project views are grouped and displayed in the Project Browser. You can customize sorting by Discipline, Level, View Type, or any parameter applicable to views.”In the given exhibit, the Project Browser structure shows views grouped first by discipline (“Coordination,” “Electrical”), then by level (“Level 1,” “Level 2”), and finally by view type (e.g., “Floor Plans,” “Ceiling Plans”). This organization allows the electrical designer to isolate MEP-related views while maintaining logical grouping under each building level.
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 14 of 17A. B. C. D. To achieve this layout, the designer must apply the following browser organization setup in the Browser Organization Properties dialog box:1## Group by: Discipline – creates top-level folders such as Architectural, Structural, Electrical, etc.2## Then by: Associated Level – organizes each discipline into subfolders based on floor levels (Level 1, Level 2, etc.).3## Then by: Family and Type – further organizes the level folders into view categories (e.g., Floor Plans, Ceiling Plans).This configuration is supported by the Smithsonian Facilities Revit Template User’s Guide:“Grouping by Discipline, Level, and View Type provides logical organization for MEP coordination, facilitating efficient access to electrical floor and ceiling plan views.”Sorting by View Name (Ascending) ensures consistent alphabetical listing under each category.References:Autodesk Revit MEP User’s Guide – Chapter 41 “Browser Organization and View Management,” pp. 896–903Smithsonian Facilities Revit Template User’s Guide – Section 2.8 “Browser View and Sheet Organization Settings,” pp. 28–30Autodesk Revit Electrical Design Essentials – “Project Browser Customization for MEP Disciplines”Question #:9 - [Electrical Systems and Circuiting]How can an arrowhead be added to a lag leader line?Change the Leader Type to Free End.Enable Leader Arrowhead in the instance properties.Choose an arrow type for the Leader Arrowhead in the Type Properties.Select the tag and enable Leader Line in the Properties paletteAnswer: CExplanationIn Autodesk Revit for Electrical Design, arrowheads on leader lines—such as those used with tags, text notes, or annotations—are controlled through Type Properties, not through instance properties or free-end options.
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 15 of 17A. B. C. D. According to the Revit MEP User’s Guide – Annotating Chapter (Chapter 47 and 42), the section “Modifying Tags” explains:“Select the tag, and on the Properties palette, click (Edit Type). In the Type Properties dialog, select a value for Leader Arrowhead to add an arrowhead to the leader line.”This confirms that the arrowhead is defined at the type level, meaning any change applies to all tags or text notes of that annotation type throughout the project. The Leader Arrowhead property allows the designer to choose from predefined arrowhead styles (like “Filled Arrow,” “Dot,” “Tick Mark,” etc.), which are defined globally under:Manage tab # Settings panel # Additional Settings # Arrowheads.Furthermore, the document specifies under “Leader Arrowhead Properties”:“Sets the arrowhead shape on the leader line. The value is the name of the arrowhead style defined by the Arrowheads tool.”This behavior applies to all annotation categories, including text notes, keynotes, material tags, and electrical device tags, maintaining consistency across all view types in an electrical project.Therefore, Option C is the correct answer because arrowheads are configured via Type Properties, while the other options are inaccurate:Option A (Free End) only defines leader attachment behavior.Option B (Instance properties) does not include a “Leader Arrowhead” toggle.Option D (Enable Leader Line) only adds or removes a leader line, not the arrowhead style.References:Autodesk Revit MEP User’s Guide – Chapter 47 “Annotating,” pp. 1040–1055Autodesk Revit MEP User’s Guide – Chapter 42 “Text Notes and Tags,” pp. 936–949Autodesk Revit Electrical Design Essentials – “Leader Arrowhead Properties and Annotation Standards”Question #:10 - [Lighting and Switch Systems]An electrical designer is adding lights to a project model. The coiling grids arc located in a linked Revit model. How are these lights affected if the grid patterns move?The lights do not move with the pattern but will stay associated with the ceiling if hostedThe lights move with the pattern if they are alignment-locked to the ceiling and hosted.The lights do not follow grid pattern movement unless they are non-hosted.
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 16 of 17D. The lights move with the pattern if they are defined as ceiling-hosted types.Answer: AExplanationWhen working in Autodesk Revit for MEP Electrical Design, lighting fixtures can be either hosted (such as ceiling-hosted or wall-hosted) or non-hosted. The movement of lighting fixtures in relation to linked model elements—like ceiling grids—is determined by the hosting condition and alignment constraints applied to those elements.According to the Revit MEP User’s Guide (Chapter 24 “Ceilings” and Chapter 50 “Rendering”), a ceiling is a level-based element. You can create it on a specified level and host ceiling-based families such as lighting fixtures. When a ceiling is modified or repositioned, the hosted lighting fixtures will move with the ceiling itself, maintaining their relationship to the host surface. However, when ceiling grid patterns are changed or moved in a linked Revit model, the movement of those grid patterns does not automatically propagate to hosted elements in the electrical model unless those elements are directly linked or constrained to a movable reference plane.As described:“Ceilings are level-based elements… When you create a ceiling, you can host components such as lighting fixtures on its face. Hosted elements remain associated with their host even if the ceiling is modified.”And further in the glossary section:“Rehost: To move a component from one host to another. For example, you can use the Pick New Host tool to move a window from one wall to another wall.”This confirms that a hosted light fixture maintains its attachment to the host element (the ceiling) but not to the grid pattern itself. Grid movement within a linked ceiling model does not alter the position of lights unless they are manually re-hosted or alignment-locked directly to a specific geometry within the host model.Therefore, the correct interpretation is that when ceiling grid patterns move within a linked Revit model, the lights placed in the electrical model do not follow the grid pattern movement automatically. They remain stationary relative to the ceiling surface, provided they are hosted correctly.This behavior reflects Revit’s parametric relationships — “hosted elements maintain dependency only on their host, not on graphical references like grids unless locked via constraints.”References:Autodesk Revit MEP User’s Guide, Chapter 24 “Ceilings”, pp. 579–583Autodesk Revit MEP User’s Guide, Chapter 50 “Rendering” (Lighting Fixtures and Hosts)Autodesk Revit Glossary: “Rehost” definition, p. 2037Revit Electrical Design Parametric Model Behavior – Revit MEP Essentials
Certs Exam Autodesk - RVT_ELEC_01101Pass with Valid Exam Questions Pool 17 of 17
About certsout.comcertsout.com was founded in 2007. We provide latest & high quality IT / Business Certification Training Exam Questions, Study Guides, Practice Tests.We help you pass any IT / Business Certification Exams with 100% Pass Guaranteed or Full Refund. Especially Cisco, CompTIA, Citrix, EMC, HP, Oracle, VMware, Juniper, Check Point, LPI, Nortel, EXIN and so on.View list of all certification exams: All vendorsWe prepare state-of-the art practice tests for certification exams. You can reach us at any of the email addresses listed below.Sales: [email protected]: [email protected]: [email protected] problems about IT certification or our products, You can write us back and we will get back to you within 24 hours.