GK Installation Guide

MIXING AND APPLICATION INSTRUCTIONS(NP015)

PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using. Continuous storage
should be between 60 and 90 degree F. Keep from freezing.

SURFACE PREPARATION: Surface preparation will vary according to the type of complete system to be applied. For a one or two coat
thin build system (3-10 mils dry) we recommend either mechanical scarification or acid etching until a suitable profile is achieved. All
dirt, oil, dust, foreign contaminants and laitance must be removed to assure a trouble free bond to the substrate. A test should be
made to determine that the concrete has an appropriate vapor barrier. This can be done by placing a 4’X4’ plastic sheet on the
substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate does not
show signs of eventual hydrostatic pressure problems that may later cause disbanding. However, this product can be applied to a damp
floor as long as there are not standing puddles.

PRODUCT MIXING: This product comes pre-packaged by weight. Kits should be mixed in their entirety. If partial kits are to be used,
refer to the front of this technical data for proper weight mix ratios. After the two parts are combined, mixes well with slow speed
mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. This product is an emulsion product and
should be mixed well before using.

PRODUCT APPLICATION: The mixed material can be applied by brush or roller. Maintain temperatures within the recommended
ranges during the application and curing process. Apply material with relative humidity within the parameters shown on the technical
data. When the end of the pot life has been reached, you will find that the material becomes hard to apply and will actually tend to roll
back up onto the roller. Do not try to continue application when the coating has reached this step. Applications made at different
times with differing environmental conditions, may show slight variations in gloss.

RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that all of the solvents and water have
evaporated from the coating during the curing process. It is best to test the coating before recoating or topcoating. This can be done
by pressing on the coating with your thumb to verify that no fingerprint impression is left. If no impression is created, then the recoat
or topcoat can be started. Always remember that colder temperatures will require more cure time for the product before recoating or
topcoating can commence. Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish,
greasy film or deglossing). If a blush is present, it must be removed prior to topcoating or recoating. A standard type detergent cleaner
can be used to remove any blush. Many epoxy overlays and coatings as well as urethanes are compatible for use as a topcoat for this
product as well as multiple coats of this product.

CLEANUP: Use PM solvent or Water FLOOR CLEANING: Caution! Some cleaners may affect the color of the floor installed. Test each
cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and
process tested.

RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data
under full cure). It is best to let the floor remain dry for the full cure cycle. Dependent on actual complete system application, surface
may be slippery, especially when wet or contaminated; keep surface clean and dry.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY

We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge.
Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the
suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties
are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON
WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE
MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR
PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net
selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty
whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or
assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ
THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

COPYRIGHT 9/1/12 NORKAN.

PRODUCT Devran® 224V
DESCRIPTION
Epoxy

A high performance, multi-purpose, surface tolerant, two-component chemically-cured epoxy semi-gloss
coating for industrial or high performance architectural coating (HIPAC) applications. For use on
properly prepared steel or masonry surfaces.

INTENDED USES Ideal for structural steel, piping, tanks, and equipment in chemical, fertilizer, power plants, petroleum
refineries, pulp and paper mills, water and sewage treatment plants and mining operations. Can also be
used in the hard service areas of correctional facilities, schools, commercial and restaurant kitchens
where a high performance architectural coating (HIPAC) is required.

PRACTICAL Color White and custom colors
INFORMATION FOR Gloss Level
DEVRAN 224V Volume Solids Semi Gloss

Typical Thickness 77% ± 2%

Theoretical Coverage 6 mils (150 microns) dry equivalent to 7.8 mils (195 microns) wet

Practical Coverage 206 sq.ft/US gallon at 6 mils d.f.t and stated volume solids
5.10 m²/liter at 150 microns d.f.t and stated volume solids
Allow appropriate loss factors

Method of Application Airless Spray, Air Spray, Brush, Roller

Drying Time Overcoating Interval with
Temperature recommended topcoats

Touch Dry Hard Dry Minimum Maximum

41°F (5°C) 21 hours 43 hours 21 hours Extended¹
50°F (10°C) 18 hours 23 hours 18 hours Extended¹
77°F (25°C) 90 minutes 5 hours 90 minutes Extended¹
104°F (40°C) 60 minutes 60 minutes 60 minutes Extended¹

¹ See International Protective Coatings Definitions & Abbreviations

REGULATORY DATA Flash Point Part A 82°F (28°C); Part B 81°F (27°C); Mixed 73°F (23°C)

Product Weight 12.5 Ib/gal (1.5 kg/l) EPA Method 24
VOC 0.23 lb/gal (28 g/lt)

See Product Characteristics section for further details

Protective Coatings

Page 1 of 4
Issue Date:4/26/2012
Ref:4690



PRODUCT Pre-Prime® 167
DESCRIPTION
Epoxy
INTENDED USES
A high performance, two-component chemically-cured 100% solids epoxy penetrating sealer.

Improves the effectiveness and efficiency of the maintenance painting process by penetrating and
sealing crevices, joints, back-to-back angles of existing structures, and edges of old coatings, improving
the service life of the maintenance system. Also serves to seal aged “white rusted” zinc surfaces for
recoating.

Recommended for rusty steel when environmental economic or safety concerns restrict abrasive blast
cleaning. The extraordinary penetrating properties of Pre-Prime 167 provide a means of reinforcing
rusty steel substrates, ensuring adhesion of subsequent coatings. Equally effective at penetrating,
reinforcing and sealing concrete and masonry surfaces in all industrial environments.

PRACTICAL Color Colorless
INFORMATION FOR Gloss Level Semi-gloss
PRE-PRIME 167 Volume Solids 100%

Typical Thickness 1-1.5 mils (25-38 microns) dry equivalent to 1-1.5 mils (25-38 microns)
wet

Theoretical Coverage 1253 sq.ft/US gallon at 1.3 mils d.f.t and stated volume solids
31.30 m²/liter at 32 microns d.f.t and stated volume solids

Practical Coverage Allow appropriate loss factors

Method of Application Airless spray, Air spray, Brush, Roller
Drying Time
Touch dry and hard dry information is not applicable for Pre-Prime 167

Minimum overcoating interval is when the Pre-Prime 167 film 'sets up'
and becomes tacky.

Maximum overcoating interval is 72 hours after the Pre-Prime 167 film
becomes tacky.

REGULATORY DATA Flash Point Part A 214°F (101°C); Part B 135°F (57°C); Mixed 109°F (43°C)

Product Weight 8.5 Ib/gal (1.02 kg/l)

VOC 0.79 lb/gal (95 g/lt) EPA Method 24

See Product Characteristics section for further details

Protective Coatings

Page 1 of 4
Issue Date:11/8/2011
Ref:4421

SURFACE Pre-Prime® 167
PREPARATION
Epoxy

All surfaces must be sound, dry, clean, and free of oil, grease, dirt, loose and flaking paint and other
foreign substances.

Rusty Steel and Weathered Rusty Galvanized Metal
Pre-Prime 167 is designed for less than ideal surface preparation. However, performance will be
improved as surface preparation improves. Best performance will be obtained by treating all surfaces
with Devprep 88 or other suitable cleaner, followed by a high pressure water wash before applying Pre-
Prime 167.

Concrete and Masonry
Remove oil, grease, mildew, form release agents, loose laitance and foreign matter.

Previously Painted Surfaces:
Remove all loose and peeling paint, loose rust or other surface contaminants. Clean using Devprep 88
or other suitable cleaner, followed by high pressure water wash. Apply a test patch of Pre-Prime 167 to
confirm compatibility with existing coating systems.

APPLICATION Mixing Material is supplied in two containers as a unit. Always mix a complete unit in
the proportions supplied. Once the unit has been mixed, it must be used within
Mix Ratio the working pot life specified.
Working Pot Life (1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base
Airless Spray
(Part A) and mix thoroughly with power agitator.
Air Spray
(Conventional) 3 part(s) : 1 part(s) by volume
Brush
Roller 50°F (10°C) 59°F (15°C) 77°F (25°C)
Thinner
Cleaner 6 hours 5 hours 4 hours
Work Stoppages
Recommended Use a 9 thou (0.22mm) tip size and adjust pressure
Clean Up Recommended as needed.

Suitable See Product Characteristics section for further details
Suitable

DO NOT THIN

T-10 Thinner

Do not allow material to remain in hoses, gun or spray equipment. Thoroughly
flush all equipment with T-10 Thinner. Once units of paint have been mixed
they should not be resealed and it is advised that after prolonged stoppages
work recommences with freshly mixed units.

Clean all equipment immediately after use with T-10 Thinner. It is good working
practice to periodically flush out spray equipment during the course of the
working day. Frequency of cleaning will depend upon amount sprayed,
temperature and elapsed time, including any delays. All surplus material and
empty containers should be disposed of in accordance with appropriate
regional regulations/legislation.

Page 2 of 4

SURFACE Devran® 224V
PREPARATION
Epoxy

All surfaces must be sound, dry, clean, free of oil, grease, dirt, mildew, curing compounds, loose and flaking
paint and other foreign substances.

New Surfaces:
New Steel: Surfaces should be initially blasted to near-white metal surface cleanliness in accordance with
SSPC-SP10 or ISO-Sa2½ for immersion service or commercial blast cleanliness in accordance with SSPC-
SP6 or ISO-Sa2 for non-immersion service. Blast profile on steel should be 1.2 - 2.5 mils (38-63 microns) in
depth and be of a sharp, jagged nature as opposed to a 'peen' pattern (from shot blasting).
Concrete Block: Remove loose aggregate and repair voids. Fill with Devran 224V or Tru-Glaze WB 4015
block filler.
Concrete Floors, Poured Concrete: Cure at least 30 days. Acid etch or abrasive blast slick, glazed concrete
or concrete with laitence. Prime with Pre-Prime 167 or Devran 224V.
Galvanized Steel: Remove dirt and oils by solvent cleaning or with Devprep 88 cleaner or other suitable
cleaner followed by a thorough water rinsing. Prime with Devran 203 or Devran 201H epoxy primers for non-
immersion. For severe moisture conditions, abrasive blasting is recommended before priming with Devran
224V or Devran 201H epoxy primer.

Previously Painted Surfaces Old coatings should be tested for lifting. If lifting occurs, remove the coating.
Otherwise, scuff sand glossy areas and aged epoxy coatings. Clean aged epoxy or urethane coatings with
Devprep 88 Cleaner or other suitable cleaner followed by thorough rinsing. Remove cracked and peeling
paint. Prime bare areas with appropriate primer.

APPLICATION Mixing Devran 224V coating is a two component product supplied in 10 Gallon and 2
Gallon kits which contain the proper ratio of ingredients. The entire contents of each
Mix Ratio container must be mixed together. Power mix both portions first to obtain a smooth,
Working Pot Life homogeneous condition, then add the converter slowly with continued agitation.
After the converter addition is complete, continue to mix slowly. Allow the mixed
Airless Spray material to stand for 15 minutes at 60-80°F (16-27°C) before use. Always re stir
before use. Avoid storing or placing containers in direct sunlight.
Air Spray
(Pressure Pot) 1 part(s) : 1 part(s) by volume
Brush
Roller 41°F (5°C) 59°F (15°C) 77°F (25°C)
Thinner 6 hours
Cleaner 6 hours 6 hours
Work Stoppages
Recommended Tip Range 15-17 thou (0.38-0.42 mm)
Clean Up Recommended Total output fluid pressure at spray tip not less than 2204
psi (155 kg/cm²)

Suitable Typically 4.0 mils (100 microns) can be achieved
Suitable Typically 4.0 mils (100 microns) can be achieved

T-10 or T-0 Thinner, depending on VOC regulations.

T-10 or T-0 Thinner, depending on VOC regulations.

Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush
all equipment with T-10 or T-0 Thinner, depending on VOC regulations. Once units
of paint have been mixed they should not be resealed and it is advised that after
prolonged stoppages work recommences with freshly mixed units.

Clean all equipment immediately after use with T-10 or T-0 Thinner, depending on
VOC regulations. It is good working practice to periodically flush out spray
equipment during the course of the working day. Frequency of cleaning will depend
upon amount sprayed, temperature and elapsed time, including any delays. All
surplus material and empty containers should be disposed of in accordance with
appropriate regional regulations/legislation.

Page 2 of 4

Devran® 224V

Epoxy

PRODUCT Advantages:
CHARACTERISTICS
- Excellent corrosion protection
- Resists splash and spillage of solvents, alkalis, salts, moisture, oils, greases, foodstuffs and detergents
- Cold weather cure - application down to 25°F (-4°C)
- Surface tolerant
- Low VOC
- Self-priming on steel or masonry
- Abrasion resistant
- High build/high solids coating

Tinting: Tint the appropriate base with Industrial colourants. (Do not use water based or other colourants).
Add colourants to only the base portion. Mix thoroughly before adding the converter portion.
Thinning: Thinning is not normally required or desired. However, at lower temperatures, small amounts (5% or
less) of T-10 thinner can be added depending on local VOC and air quality regulations. Any solvent addition
should be made after the two components are thoroughly mixed.

Do not apply if relative humidity exceeds 85% or temperature is within 5°F (3°C) of the dew point.

Limitations of Use: Exterior exposure will cause a colour change, early dulling, and loss of gloss, but this does
not affect protective properties. Epoxy coatings may yellow during application and cure if exposed to the
combustion by-products of improperly vented fossil fuel burning heaters. Commonly finished with Devthane
Urethane Enamel for maximum exterior colour and gloss retention.

Cold Weather Applications: For substrate temperatures between 25°F (-4°C) and 40°F (5°C) cold weather
additive 060A0000 may be added. Two pint containers of 060A0000 may be added to the converter portion of
a 10 Gallon kit of Devran 224HS Coating. Thoroughly mix the 060A0000 additive in the converter with a
power mixer prior to adding the converter to the base portion.

Where Devran 224V is to be overcoated with Devthane 349QC, 378H or 379H the following overcoating
intervals will apply:

41°F (5°C) Minimum Maximum
59°F (15°C) 20 hours 7 days
68°F (20°C) 8 hours 7 days
77°F (25°C) 6 hours 5 days
3 hours 3 days

Where Devran 224V is to be overcoated with Devthane 359H the following overcoating intervals will apply:

41°F (5°C) Minimum Maximum
59°F (15°C) 20 hours 15 days
68F (20°C) 8 hours 10 days
77°F (25°C) 6 hours 7 days
3 hours 7 days

Note: VOC values are typical and are provided for guidance purpose only. These may be subject to variation
depending on factors such as differences in color and normal manufacturing tolerances.

SYSTEMS The following primers are recommended for Devran 224V:
COMPATIBILITY
Bar-Rust 231 Devran 203
Bar-Rust 231LV Devran 224V
Bar-Rust 235V Devguard 4300
Cathacoat 302H Tru-Glaze-WB 4030
Devran 201H

The following topcoats are recommended for Devran 224V:

Devthane 349QC Devthane 378H
Devthane 359H Devthane 379
Devthane 378 Devthane 379H

Page 3 of 4

MIXING AND APPLICATION INSTRUCTIONS (Norklad 100M)

1) PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using.
Continuous storage should be between 60 and 90 degree F. Low temperatures or temperature fluctuations may cause
crystallization.

2) SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast) to remove all
laitance and provide a suitable profile. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble
free bond to the substrate. A test should be made to determine that the concrete is dry; this can be done by placing a 4’X4’
plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet,
then the substrate is dry enough to start coating. The plastic sheet testing is also a good method to determine if any
hydrostatic pressure problems exist that may later cause disbanding.

3) PRODUCT MIXING: This product has a mix ratio of 9.0# part A to 4.15# part B. Standard packages are in pre-measured
kits and should be mixed as supplied in the kit. We highly recommend that the kits not be broken down unless suitable
weighing equipment is available. After the two parts are combined, mix well with slow speed mixing equipment such as a
jiffy mixer until the material is thoroughly mixed and streak free. After mixing, transfer the mixed material to another pail (the
transfer pail) and again remix. The material in the transfer pail is now ready to be applied on the primed substrate. Improper
mixing may result in product failure.

4) PRIMING: A suitable primer should be used before applying this product. See the front side of this technical data for
primer information. If a primer is not used, more porous substrates may cause outgassing and possible surface defects.

5) PRODUCT APPLICATION: The mixed material can be applied by brush or roller. However, the material can also be
applied by a suitable serrated squeegee and then back rolled as long as the appropriate thickness recommendations are
maintained. Maintain temperatures and relative humidity within the recommended ranges during the application and curing
process. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be
used prior to the coating tacking off to remove the air entrapped in the coating. This product can be used with various
colored sand in a broadcast system or other suitable aggregate can be used in conjunction with this product to achieve a
variety of color and application patterns. Contact your representative for details as necessary.

6) RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has
tacked off before recoating. Always remember that colder temperatures will require more cure time for the product before
recoating or topcoating can commence. Before recoating or topcoating, check the coating to insure no epoxy blushes were
developed (a whitish, greasy film or deglossing). If a blush is present, it must be removed prior to topcoating or recoating.
Many epoxy coatings and urethanes are compatible for use as a topcoat for this product as well as multiple coats of this
product.

7) CLEANUP: Use xylol.

8) FLOOR CLEANING: Caution! Some cleaners may affect the color. Test each cleaner in a small area. If no ill effects are
noted, you can continue to clean with the product and process tested.

8) RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see
technical data under full cure). It is best to let the floor remain dry for the full cure cycle.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND
LIMITATIONS ON OUR LIABILITY

We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our
knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own
tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of
the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED,
REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0
WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT
FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE
UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our
product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty
whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or
warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL
INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

COPYRIGHT 1/1/11

Norklad 200 is a two component 100% (+/- 1%) solids epoxy colored coating designed for applications where a high build colorfast impact
resistant floor is needed. It is recommended for a high build topcoat or basecoat on concrete or masonry. Product is suitable in many
chemical exposure environments. It can be used as a broadcast coat for full broadcast colorchip floor system.

SOLIDS BY WEIGHT: CURE SCHEDULE:
100% (+/- 1%) pot life – 1 1/2 gallon volume ………..………30-50 minutes @ 70° F
SOLIDS BY VOLUME: tack free (dry to touch)……….…...……………..…5-8 hours @ 70° F
100% (+/- 1%) recoat or topcoat.....…………….……..………..... 8-12 hours @ 70°F
VOLATILE ORGANIC CONTENT: light foot traffic...……………...……………..……12-14 hours @ 70°F
Nearly zero pounds per gallon full cure (heavy traffic)... ..……………………...…....2-7 days @ 70°F

STANDARD COLORS: APPLICATION TEMPERATURE:
Off White, Beige, Taupe, Tan, Light Gray, Medium Gray, 60-90 degrees F with relative humidity below 85%
Charcoal, Tile Red, White, Black
NON-STANDARD COLORS: CHEMICAL RESISTANCE:
Royal Blue, Green, Wheat, Steel Blue, Traffic Yellow
REAGENT RATING
RECOMMENDED FILM THICKNESS: 12-30 mils
xylene C
COVERAGE PER GALLON:
53-130 square feet per gallon @ 12-30 mils trichloroethylene B
(80 to 100 sq/ft per gal for best results)
PACKAGING INFORMATION methanol A
3 gallon kits (2.9 – 3.0 gallons net approximately)
15 gallon kits (14 – 15 gallons net approximately) eskthyydlraoMllcoIhXol ING AND APPLICATIONBB
MIX RATIO:
12 pounds (1 gallon) part A to 4.15 pounds (.50 gallons) part B 10% sodium hydroxide E
(volumes approx.) (standard colors)
SHELF LIFE: 50% sodium hydroxide D
1 year in unopened containers C
FINISH CHARACTERISTICS: 10% sulfuric aIcNid STRUCTIONS (NP707)
Gloss (70-95 at 60 degrees @ Erichsen glossmeter) 70% sulfuric acid A
ABRASION RESISTANCE:
Taber abraser CS-17 calibrase wheel with 1000 gram total 10% HC1 (aq) C
load and 500 cycles = 32 mg loss
FLEXURAL STRENGTH: 5% acetic acid B
5,400 psi @ ASTM D790
COMPRESSIVE STRENGTH: Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour
9,100 psi @ ASTM D695 – 1/2 ”X 1/2” bars
ADHESION: term splash spill, D - 72 hour immersion, E - long term immersion. NOTE:
450 psi @ elcometer (concrete failure, no delamination)
VISCOSITY: extensive chemical resistance information is available through your sales
Mixed = 1300-2300 cps (typical, most colors)
DOT CLASSIFICATIONS: representative.
Part A “not regulated”
Part B “CORROSIVE LIQUID N.O.S., 8, UNI1760, PGIII” PRIMER:
TENSILE STRENGTH: Recommended. Waterborne Epoxy or Penetrating Primer.
4,800 psi @ ASTM D638 TOPCOAT:
ULTIMATE ELONGATION: Optional – aliphatic urethanes can be used for increased chemical
3.1% resistance or increased UV stability.
GARDNER VARIABLE IMPACTOR:
50 inch pounds direct – passed LIMITATIONS:
HARDNESS: *Color stability or gloss may be affected by environmental conditions such
Shore D = 80 as high humidity, low temperatures, chemical exposure or exposure to
certain types of lighting such as sodium vapor lights.
*Colors may vary from batch to batch. Therefore, use only product from the
same batch for an entire job.
*This product is not UV color stable and may discolor when exposed to UV
lighting. Otherwise, the color stability of this product is good. Therefore, a
topcoat is optional and dependent on the environment.
*Light or bright colors may require a suitable primer or topcoat to achieve a
satisfactory hide.
*Substrate temperature must be 5°F above dew point.
*All new concrete must be cured for at least 30 days prior to application.
*Apply a suitable primer before using this product for best results.

PRODUCT STORAGE: Store product at normal room temperature before using. Continuous storage should be between 60
and 90 degree F. Low temperatures or temperature fluctuations may cause product crystallization.

SURFACE PREPARATION: All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to
the substrate. A test should be made to determine that the concrete is dry; this can be done by placing a 4’X4’ plastic sheet
and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet then the substrate is dry
enough to start repair work. This product is intended for hairline cracks and other fractures up to an 1/8 inch in width.
Remove all unsound concrete from within the crack to be repaired and thoroughly vacuum all debris and dust from within the
crack opening.

PRODUCT MIXING: This product has a mix ratio of 1 part A to 1 part B by volume. To mix, simply measure out equal
volumes of the material and mix them together thoroughly with slow speed mixing equipment such as a jiffy mixer, putty knife
or spatula until the material is thoroughly mixed and uniform in color. Mix only an amount of material that can be used in the
allotted pot life period. Improper or insufficient mixing may result in product failure.

PRIMING: No priming is necessary.

PRODUCT APPLICATION: The mixed material can be applied by marginal trowel, putty knife or any other suitable
equipment.

RECOAT OR TOPCOATING: When repairing cracks that are less than 1/8” thickness, many epoxies can be placed directly
over the applied crack filler before it is cured. Alternatively, it is also acceptable to allow the material to cure before installing
the coating. If excessive amounts are spread well beyond the crack repair or in an areas where surface repairs have been
implemented, it is best to check the cured areas for any possible amine blush (a whitish, greasy film or deglossing) prior to
coating over this material. If a blush is present, it can be removed by any standard type detergent cleaner prior to topcoating
or recoating. Many epoxy coatings and urethanes are compatible for use over this product as well as multiple coats of this
product.

CLEANUP: Use xylol.

FLOOR CLEANING: Caution! Some cleaners may affect the color of the fast gel installed. Test each cleaner in a small
area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process
tested.

RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see
technical data under full cure). It is best to let the floor remain dry for the full cure cycle.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND
LIMITATIONS ON OUR LIABILITY

We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such
information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our
product for your particular purpose. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED,
REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE,
EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO
WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental
or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of
our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No
representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that
may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY
HARM.

COPYRIGHT4/21/03

Norklad 100-M is a two component 100% solids epoxy seal coat that can be used either as a coating or filled with paint chips, marble chips
and colored sand mixtures to provide an infinite array of color schemes or patterns.

This product is recommended for warehouses, kitchens, restrooms, and other areas where either a high build clear product is needed or
where a decorative filled floor is desired.

SOLIDS BY WEIGHT: CURE SCHEDULE:

100% pot life – 1 1/2 gallon volume ………… 20-30 minutes @ 70° F
tack free (dry to touch)…….………….……..…6-8 hours @ 70° F
SOLIDS BY VOLUME: recoat or topcoat.....…………….………..... 10-16 hours @ 70°F
light foot traffic...………………………..……14-18 hours @ 70°F
100% full cure (heavy traffic)...…………………...…....2-7 days @ 70°F

VOLATILE ORGANIC CONTENT: APPLICATION TEMPERATURE:

Nearly zero pounds per gallon 55-90 degrees F

STANDARD COLORS: CHEMICAL RESISTANCE:

Clear – gardner color 1-2 REAGENT

RECOMMENDED FILM THICKNESS: RATING

16-18 mils butanol C

COVERAGE PER GALLON: xylene C

90-100 square feet per gallon @ 16-18 mils 1, 1, 1 trichloroethane B

PACKAGING INFORMATION MEK A

1.5 gallon kits methanol A
3 gallon kits (2.95 gallons net approximately)
15 gallon kits (14.75 gallons net approximately) ethyl alcohol C

MIX RATIO: skydrol B

9.0 pounds part A (.99 gallons) to 4.15 pounds part B (.49 10% sodium hydroxide E
gallons) (volumes approx.)
50% sodium hydroxide D
SHELF LIFE:
10% sulfuric acid C
1 year in unopened containers
70% sulfuric acid A
FINISH CHARACTERISTICS:
10% HC1 (aq) C
Gloss (60 to 90 @ 60 degrees @ glossmeter)
5% acetic acid B
ABRASION RESISTANCE:
Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour
Taber abraser CS-17 calibrase wheel with 1000 gram total load
and 500 cycles = 36 mg loss term splash spill, D - 72 hour immersion, E - long term immersion. NOTE:

FLEXURAL STRENGTH: extensive chemical resistance information is available through your sales

7,400 psi @ ASTM D790 representative.

COMPRESSIVE STRENGTH: PRIMER:

11,200 psi @ ASTM D695 Recommended Norklad WB or alternate

ADHESION: TOPCOAT:

350 psi @ elcometer (concrete failure, no delamination) Optional HPU 747 aliphatic urethanes or successive coats or
Norklad 100-M in aggregate filled systems, with or without a
VISCOSITY: clear urethane topcoat.

Mixed = 700-1000 cps (typical) LIMITATIONS:

DOT CLASSIFICATIONS: *Color stability or gloss may be affected by environmental

Part A “not regulated” conditions such as high humidity, chemical exposure, UV
Part B “CORROSIVE LIQUID N.O.S., 8, UNI1760, PGIII”
exposure or exposure to lighting such as sodium vapor lights.
TENSILE STRENGTH:
*This product is not UV color stable. Clear aliphatic urethane
7,600 psi @ ASTM D638
topcoats reduce (UV light) color changes.
ULTIMATE ELONGATION:
*Substrate temperature must be 5°F above dew point.
4.1% *For best results, apply with a ¼” or 3/8” nap roller.

GARDNER VARIABLE IMPACTOR: *All new concrete must be cured for at least 30 days prior to

50 inch pounds direct – passed application.

HARDNESS: *Apply a suitable primer before using this product

Shore D = 81 *See reverse side for application instructions.

*Physical properties are typical values and not specifications.

*See reverse side for limitations of our liability and warranty.

HPU 747 Urethane Color Coat is a two component polyester/aliphatic polyurethane floor sealer that exhibits excellent characteristics for abrasion
resistance, chemical resistance, flexibility, weathering and UV stability. It is recommended for auto service centers, warehouses, computer rooms,
laboratories, aircraft hangers, cafeterias, exterior tanks, indoor or outdoor service and chemical exposure areas.

SOLIDS BY WEIGHT: CURE SCHEDULE: (70°F)

Mixed= 60% (colors) pot life – 1 1/2 gallons volume ...…..………….…………………….... 2-5 hours
tack free (dry to touch)…………...………………………………………...…2-4 hours
SOLIDS BY VOLUME: recoat or topcoat.....…………….………..……………...………………....... 4-8 hours
light foot traffic...……………………………………………….………..……14-24 hours
Mixed= 53% (colors) full cure (heavy traffic).................…………………..……………...…....3-5 days

VOLATILE ORGANIC CONTENT: APPLICATION TEMPERATURE:

Less than 3.8 pounds per gallon 45-90 degrees F

STANDARD COLORS: CHEMICAL RESISTANCE:

White, off white, light gray, slate gray, charcoal, tile red, beige, REAGENT RATING
taupe, wheat, and clear
acetic acid 5% C
RECOMMENDED FILM THICKNESS:
xylene E
3-5 mils per coat wet thickness (yields 2-3 mils dry)
mek B
COVERAGE PER GALLON:
methyl alcohol B
320 to 500 square feet @ 3-5 mils wet thickness
gasoline D
PACKAGING INFORMATION
10% sodium hydroxide E
3 gallon and 15 gallon kits 3 gal kit= 2 gallons part A (10.5#/gal-
colors) or (8.75#/gal-clear) and 1 gallon part B (8.5#/gal.) (weights 50% sodium hydroxide D
and volumes approximate)
10% sulfuric D
MIX RATIO:
10% hydrochloric acid D
2 parts A to 1 part B by volume
20% nitric acid C
SHELF LIFE:
ethylene glycol D
1 year
Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term
FINISH CHARACTERISTICS:
splash spill, D - 72 hour immersion, E - long term immersion. NOTE: extensive
High gloss (>80 at 60 degrees @ Erichsen glossmeter)
chemical resistance information is available through your sales representative.
ABRASION RESISTANCE:
PRIMER:
Taber abrasor CS-17 calibrase wheel with 1000 gram total load and
500 cycles = 20.0 mg loss Recommend Norklad WB, Norklad 200, Norklad 200-LVP,

IMPACT RESISTANCE: TOPCOAT:

Gardner Impact, direct & reverse = 160 in. lb. (passed) None recommended

FLEXIBILITY: LIMITATIONS:

No cracks on a 1/8” mandrel *Colors or gloss may be affected by high humidity, low temperatures,
chemical exposure, or exposure to lighting such as sodium vapor lights.
ADHESION: *For best results use a high quality 3/8” nap roller.
*Slab on grade requires moisture barrier
360 psi @ elcometer (concrete failure, no delamination)
MIXING AND APPLICATION*Substrate temperature must be 5°F above dew point
VISCOSITY:
*All new concrete must be cured for at least 30 days
Mixed = 200-400 cps (typical, most colors) *Physical properties are typical values and not specifications
*Light or bright colors (white, safety yellow, etc.) may require multiple
DOT CLASSIFICATIONS:
INSTRUCTIONScoats or a suitable color coordinated primer to(NaPc3h2i1e)ve a satisfactory hide.
Part A “FLAMMABLE LIQUID N.O.S., 3, UN1993, PGIII”
Part B “FLAMMABLE LIQUID N.O.S., 3, UN1993, PGIII” *Tire contact may cause staining and discoloration
*Colors may vary from batch to batch, therefore, use only product from
HARDNESS: the same batch for an entire job.
*See reverse side for application instructions.
Shore D = 72 *See reverse side for limitations of our liability and warranty.

Care & Maintenance
Issue Date: 06/02/2015

General Care and Maintenance Guide

DESCRIPTION

The purpose of this guide is to provide general maintenance procedures for most of VBP products.
Please contact VBP for specific instructions for environments and or applications that are out of the
ordinary.

GENERAL HYGIENE MAINTENANCE

Day to Day

 Loose dirt, dust, and other debris can be removed by regular sweeping and /or vacuuming of the
surface.

 All spills should be cleaned up immediately to prevent chemical attack and staining in the topcoat
sealer.

As Needed

 General cleaning of stubborn surface debris can be accomplished using a mild, environmentally safe
soap solution in accordance with the manufacturer’s instructions. Harsh detergents, acids, and alkali
are not recommended as they can damage the surface.

Additional Recommendations

 Hard water stains can be cleaned with a solution of 1 part by volume white vinegar with 3-5 parts by
volume water.

TOPCOAT & SEALER MAINTENANCE

Preservation of the coating system requires proper maintenance of the sealer. Normal wearing of the
sealer coat exposes the underlying layers, which may wear, discolor, fade, and be subject to chemical
attack. The sealer should be re-coated before wearing into the underlying layers.

245 Carl Karcher Way
Anaheim, CA 92801
Tel: 714-829-2600
WWW.GARAGECOATINGS.COM

Material Safety Data Sheet

Section 1 - General Information Section 4 - Continued

Manufactured by: Great Lakes Laboratories Emergency and First Aid Procedures:

Address: 26200 Groesbeck Hwy Swallowing: Do not induce vomiting. Drink plenty of

Warren, MI 48089 water. See physician immediately.

Skin: Immediately wash with soap and water. If

24 Hour Emergency: 1-800-888-1105 irritation occurs and persists, see a physician.

Office: 1-734-525-8300 Eyes: Flush with water for at least 15 minutes, lifting

upper and lower eyelids repeatedly. See ophthalmologist.

Container over 5 liters: Phosphoric Acid Solution Inhalation: Remove to fresh air. If breathing difficulty

8, UN1805, PG III or discomfort occurs, see a physician.

Container under 5 liters: Consumer Commodity

ORM-D Section 5 - Fire and Explosion

HMIS Rating Flash Point: None

Health: 3 Extinguishing Media: N/A

Fire: 0 Special Fire Fighting Procedures: Full protective

Reactivity: 1 clothing and self-contained breathing apparatus.

Other: 0 Unusual Fire and Explosion Hazards: At flame

temperatures, will emit toxic phosphorus oxide fumes.

Section 2 - Hazardous Ingredients

Hazardous Material Description: Phosphoric Acid Section 6 - Reactivity

Class, ID NO.: Corrosive, UN1805 Stability: Stable conditions to avoid - Contact with strong

Chemical Name: Phosphoric Acid alkaline materials and reactive metals.

CAS #: 7664-38-2 Incompatibility: Contact with reactive metals may

% Weight: 40% - 60% produce flammable hydrogen/air mixtures. Reacts

Carcinogen: OSHA - No violently with strong bases.

ACGIH - No Hazardous Decomposition/By Products: At flame

temperatures, will emit toxic phosphorus oxide fumes.

Section 3 - Physical Characteristics

Boiling Point: 212°F Section 7 - Control Measures

Vapor Pressure (mm Hg) N/A Respiratory Protection: Wear mask to prevent inhalation.

Vapor Density (Air = 1) N/A Ventilation: Keep concentration below TLV level.

Specific Gravity (H2O=1): 1.24 Protective Gloves: Impervious rubber or plastic.

pH: 1.0 Eye Protection: Chemical safety goggles.

Evaporation Rate: Protective Clothing: Hat, boots and jacket may be needed

(butyl acetate = 1) Equal to Water in heavy mist or spill situation.

Solubility in Water: Complete

Appearance: Orange Liquid Section 8 - Spill/Leak Procedures

Odor: None In Case of Spill: Stop leak. Dike and absorb with inert

absorbent. Neutralize washings with soda ash or lime.

Section 4 - Health Hazard Data Waste Disposal Method: In accordance with regulations.

Exposure Limits: CERCLA Reportable Qty.: 5,000 lbs

Threshold Limit Value: 1 mg/cu. m (ACGIH) RCRA Hazard Waste #: N/A

PEL: 1 mg/cu. m (OSHA) VOC: None

STEL: 3 mg/cu. m (OSHA)

Effects of Acute Phosphoric Acid has low Section 9 - Precautions for Safety Handling

Overexposure: acute oral and moderate Handling/Storage: Store in a cool, dry place

dermal toxicity. Phosphoric Keep container closed.

Acid is corrosive to eyes. Other Precautions: Keep out of reach of

Slightly toxic if inhaled. children.

Keep from freezing.

The information contained herein is based on the data available to us and is believed to be correct. However, we make no warranty, expressed
or implied, regarding the accuracy of this data or the results to be obtained from the use thereof. We assume no responsibility for the injury from
use of the product described herein.

MIXING AND APPLICATION INSTRUCTIONS(WBU 520))

1) PRODUCT STORAGE: Store product between 60 and 90 degrees F Have material at room temperature before using. Do not freeze.

2) SURFACE PREPARATION: Surface preparation will vary according to the type of complete system to be applied. For a one or two coat
thin build system (3-10 mils dry) we recommend either mechanical scarification or acid etching until a suitable profile is achieved. For a
complete system build higher than 10 mils dry, we recommend a fine brush blast (shot blast). All dirt, oil, dust, foreign contaminants
and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete is
dry; this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still
dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good method to
determine if any hydrostatic pressure problems exist that may later cause disbonding.

3) PRODUCT MIXING: This product has a two to one mix ratio by volume- merely mix two gallons of part A with 1 gallon of part B. After
the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and
streak free. Avoid whipping air into the coating. Improper mixing may result in product failure.

4) PRODUCT APPLICATION: The mixed material can be applied by brush or roller. Maintain temperatures within the recommended
ranges during the application and curing process. Properly prime the substrate. It is best to maintain a wet edge to avoid roller marks.
Direct sunlight or high temperatures may cause visible roller marking during application. Uneven application thicknesses may cause
variations in gloss, therefore apply material as evenly in thickness as possible. Too thick of an application may result in solvent
entrapment and product failure. Although the pot life may appear to be longer, do not apply after one hour after the two components
have been mixed. Once mixed, air exposure might cause a slight skimming on the surface in the roller pan or container if left uncovered,
even for a few minutes. If skimming occurs, remove the thin layer, then stir and continue to use the product for up to an hour after it
has been mixed. Material left unused in the mixing pail or application tray may expand and foam up after an extended period of time.

5) RECOAT OR TOPCOATING: Multiple coats of this product are acceptable. If you opt to recoat this product, you must first be sure that
all of the volatile components have evaporated from the coating during the curing process. The information on the front side are
reliable guidelines to follow. However, it is best to test the coating before recoating or topcoating. This can be done by pressing on the
coating with your thumb to verify that no fingerprint impression is left. If no impression is created, then the recoat can be started.
Always remember that colder temperatures will require more cure time for the product before recoating can commence. Before
recoating or topcoating, check the coating to insure no contaminants exist. If a blush or contaminants are present on a previous coat,
remove with a standard type detergent cleaner and allow to completely dry. When recoating this product with subsequent coats of the
urethane, it is advisable to apply the recoat before 24 hours passes. Also, it is advisable to degloss the previous coat to insure a trouble
free bond.

6) CLEANUP: Use soap and water or a water soluble solvent before the coating dries.

7) FLOOR CLEANING: Caution! Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing your
cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested.

8) RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data
under full cure). It is best to let the floor remain dry for the full cure cycle.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of
our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make
your own tests to determine the suitability of our product for you particular purpose. Any use or application other than recommended herein is the sole
responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED, OR
IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. NO
WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY
PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT.
We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the
replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not
purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or
assume any other liability on our behalf with any sales of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY.
BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY HARM.

COPYRIGHT 8/6/12.

D ADDITIONAL Devran® 224V
et INFORMATION
ai Epoxy
l
T Further information regarding industry standards, terms and abbreviations used in this data sheet can
o be found in the following documents available at www.international-pc.com:
p
• Definitions & Abbreviations
• Surface Preparation
• Paint Application
• Theoretical & Practical Coverage
Individual copies of these information sections are available upon request.

SAFETY This product is intended for use only by professional applicators in industrial situations in accordance
PRECAUTIONS with the advice given on this sheet, the Material Safety Data Sheet and the container(s), and should not
be used without reference to the Material Safety Data Sheet (MSDS) which International Protective
Rect Top Coatings has provided to its customers.
PACK SIZE
All work involving the application and use of this product should be performed in compliance with all
relevant national, Health, Safety & Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will
be emitted which will require the use of appropriate personal protective equipment and adequate local
exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult International Protective Coatings for
further advice.

Unit Size Part A Part B
Vol Pack Vol Pack
1 US gal
5 US gal 1 US gal 1 US gal 1 US gal 1 US gal

5 US gal 5 US gal 5 US gal 5 US gal

For availability of other pack sizes contact International Protective Coatings

SHIPPING WEIGHT Unit Size Part A Part B
1 US gal 12.4 lb 12.7 lb
5 US gal 68.5 lb 63.6 lb

STORAGE Shelf Life 24 months minimum at 77°F (25°C). Subject to re-inspection
thereafter. Store in dry, shaded conditions away from sources of
heat and ignition.

Rect
Bottom

Disclaimer

The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first
obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product (whether in
this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application
of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the maximum extent permitted
by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by operation of law or otherwise, including, without
limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied and technical advice given are subject to our Conditions of Sale. You should request
a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous
development. It is the user's responsibility to check with their local International Paint representative that this data sheet is current prior to using the product.

This Technical Data Sheet is available on our website at www.international-marine.com or www.international-pc.com, and should be the same as this document. Should there be any
discrepancies between this document and the version of the Technical Data Sheet that appears on the website, then the version on the website will take precedence.

Copyright © AkzoNobel, 4/26/2012.

Copyright © AkzoNobel, 4/26/2012.

www.international-pc.com

Page 4 of 4

Product Data Sheet

Substrates • Concrete - Tilt up, poured, precast Features • Cleans & Etches in one step
• Masonry - Stucco, cinderblock, cement board • No Acidic Vapors
• Brick - Glazed, unglazed • Saves Time & Labor
• Neutralizes Alkali Salts
Removes • Form Release Compound • Cleans & Phosphates
• Οil, Grease, Dirt, Soot • Improves Corrosion Resistance
• Efflorescence & Laitance • Enhances Coating Adhesion
• Fabricating Oils, Lubricants
• Coolants and Rust Inhibitors
• Passivation Films

Product Description Trouble Shooting Guide
Etch 'n Clean is a concentrated, water-reducible phosphoric White Powder appearing on the surface after drying
acid and detergent blend formulated to both clean and prepare
concrete, masonry, steel, galvanized and zinc surfaces for indicates that the solution is too strong and/or the
coating, staining and sealing. Etch 'n Clean reduces contact time is too long. Remove white powder before
preparation time and cuts labor costs by eliminating the separate coating by wiping with a clean, dry cloth. To correct
pre-cleaning and rinsing operation before etching reduce solution concentration and/or reduce spray
contact time.
General Uses
Etch 'n Clean is ideal for cleaning and etching concrete floors, Safety & Health Data
walls, basements, driveways, swimming pools and containmen Etch 'n Clean is non-flammable, non-carcinogenic,
areas before coating, staining, or sealing.
and contains no petroleum or chlorinated solvents
Application ( Read precautions before using)
Etch 'n Clean can be applied with an acid-resistant, hand-pump Research
Etch 'n Clean has been accepted with an A-3
sprayer, a plastic sprinkling can, or with a plastic pail and an
category designation as a general cleaning agent on
acid-resistant broom or brush. all surfaces or for use with steam or mechanical
cleaning devices in all departments of USDA inspected
For best results: facilities.

1) Use product full strength. Availability
2) If available, hot water will accelerate cleaning Etch 'n Clean is available where ever The Original

and etching. Color Chips are sold.
3) Sweep lose debris and dampen the surface
Technical Services
with water. Technical advice furnished by The Original Color Chip

4) Apply solution and scrub with a stiff brush Company concerning any use or application of Etch 'n
Clean is reliable as current technology allows and the
or broom until bubbling stops. NOTE: if no company makes no warranty, expressed or implied of any
bubbling occurs, surface is coated with use or application for which such advice is furnished.
curing compounds or contaminants Technical assistance and information is available upon
preventing etching. Remove contamination request by writing or calling The Original Color Chip
and reapply Etch 'n Clean. Company at 586-771-6500.
5) Triple rinse with water to neutralize. On
floors, squeegee off rinse water to speed
drying. Adding baking soda will neutralize too.
6) Allow the surface to dry thoroughly.

The Original Color Chips Company / Norkan, Inc. – 26200 Groesbeck Hwy, Warren, MI 48089 USA – 1-800-227-8479

www.originalcolorchips.com www.norkan.com

Pre-Prime® 167

Epoxy

PRODUCT Advantages:
CHARACTERISTICS
- Low VOC
- Reinforces rusty steel, masonry, and aged “white rusted” zinc surfaces
- Penetrates surface rust, crevices, back-to-back angles
- Penetrates pores and tiny cracks in concrete and masonry surfaces
- Cures to a tough, water resistant coating
- Low film thickness required
- No shrinkage
- Applies easily by brush, roll or spray

Not recommended for use without a topcoat.

Air spray is preferred for appearance and build. Excessive air pressure can cause overspray problems.

For roller work, use a clean synthetic roller with 1/4" or 1/2" nap. New rollers should be thoroughly wet
with T-10 Thinner and spun vigorously to remove loose fibres. Pre-Prime 167 is low in viscosity and
usually, one coat is sufficient but porous surfaces may require two coats. Pre-Prime 167 should be
applied in one thin wet coat, sufficient to completely cover and penetrate to the steel surface. Do not
apply heavy coats and avoid puddling.

Note: VOC values are typical and are provided for guidance purpose only. These may be subject to
variation depending on factors such as differences in color and normal manufacturing tolerances.

SYSTEMS The following topcoats are recommended for Pre-Prime 167:
COMPATIBILITY

Bar-Rust 231 Bar-Rust 231LV
Bar-Rust 233H Bar-Rust 233H LV
Bar-Rust 235 Bar-Rust 235V
Bar-Rust 236 Devran 201H
Devran 203 Devran 224HS
Devran 223

Page 3 of 4

D ADDITIONAL Pre-Prime® 167
et INFORMATION
ai Epoxy
l
T Further information regarding industry standards, terms and abbreviations used in this data sheet can
o be found in the following documents available at www.international-pc.com:
p
• Definitions & Abbreviations

• Surface Preparation

• Paint Application

• Theoretical & Practical Coverage

Individual copies of these information sections are available upon request.

SAFETY This product is intended for use only by professional applicators in industrial situations in accordance
PRECAUTIONS with the advice given on this sheet, the Material Safety Data Sheet and the container(s), and should not
be used without reference to the Material Safety Data Sheet (MSDS) which International Protective
Rect Top Coatings has provided to its customers.
PACK SIZE
All work involving the application and use of this product should be performed in compliance with all
relevant national, Health, Safety & Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will
be emitted which will require the use of appropriate personal protective equipment and adequate local
exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult International Protective Coatings for
further advice.

Unit Size Part A Part B
Vol Pack Vol Pack
1 US gal
5 US gal 0.75 US gal 1 US gal 0.25 US gal 1 US quart
3 US gal 5 US gal 1 US gal 1 US gal

For availability of other pack sizes contact International Protective Coatings

SHIPPING WEIGHT Unit Size Part A Part B
1 US gal 8.4 lb 2.8 lb
5 US gal 33.7 lb 11.2 lb

STORAGE Shelf Life 12 months minimum at 77°F (25°C). Subject to re-inspection thereafter.
Store in dry, shaded conditions away from sources of heat and ignition.

Rect
Bottom

Disclaimer

The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first
obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product (whether in
this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application
of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the maximum extent permitted
by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by operation of law or otherwise, including, without
limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied and technical advice given are subject to our Conditions of Sale. You should request
a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous
development. It is the user's responsibility to check with their local International Paint representative that this data sheet is current prior to using the product.

This Technical Data Sheet is available on our website at www.international-marine.com or www.international-pc.com, and should be the same as this document. Should there be any
discrepancies between this document and the version of the Technical Data Sheet that appears on the website, then the version on the website will take precedence.

Copyright © AkzoNobel, 11/8/2011.

Copyright © AkzoNobel, 11/8/2011.

www.international-pc.com

Page 4 of 4

WBU-420 Clear is a two component high-gloss aliphatic polyurethane water based floor sealer that exhibits excellent characteristics for
abrasion resistance, chemical resistance, flexibility, weathering, and UV stability.

Recommended for auto service centers, warehouses, computer rooms, laboratories, aircraft hangers, cafeterias, and chemical exposure
areas.

SOLIDS BY WEIGHT: CURE SCHEDULE: (70°F)

Mixed= 42% pot life – (150 gram mass)…………….....………...…Minimum 1 hour
tack free (dry to touch)………………...……………………7-9 hours
SOLIDS BY VOLUME: recoat or topcoat.....…………….……..........................8-12 hours
light foot traffic...…………………………….................…24 hours
Mixed= 38% full cure (heavy traffic)... ……………..………...….......3-5 days

VOLATILE ORGANIC CONTENT: APPLICATION TEMPERATURE:

306 grams/liter 60-90 degrees F with relative humidity between 50% and 90%.

STANDARD COLORS: CHEMICAL RESISTANCE:

Clear. REAGENT RATING

RECOMMENDED FILM THICKNESS: acetic acid 5% C

3-5 mils per coat wet thickness (Do not apply thicker) xylene D

COVERAGE PER GALLON: mek B

320 to 500 square feet @ 3-5 mils wet thickness methyl alcohol B

PACKAGING INFORMATION: gasoline D

3 gallon and 15 gallon kits 3 gal kit= 2 gallons part A and 1 gallon 10% sodium hydroxide E
part B (volumes approximate) 15 gallon kit = 10 gallons part A and 5
gallons part B (volumes approximate) 50% sodium hydroxide D

MIX RATIO: 10% sulfuric D

2 parts A to 1 part B by volume 10% hydrocholoric acid D

SHELF LIFE: 20% nitric acid C

1 year in unopened containers ethylene glycol D

FINISH CHARACTERISTICS: Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term

High gloss (>70 at 60 degrees @ glossmeter) splash spill, D - 72 hour immersion, E - long term immersion. NOTE: extensive

IMPACT RESISTANCE: chemical resistance information is available through your sales representative.

Gardner Impact, direct & reverse=120 in lb (passed) PRIMER:

ABRASION RESISTANCE: Recommend:

Taber abrasor CS-17 calibrase wheel with 1000 gram total load and TOPCOAT:
500 cycles= 21.0 mg loss
None recommended
ADHESION:
LIMITATIONS:
>300 psi @ elcometer (concrete failure, no delamination) over suitable
primer * After the product is mixed, air contact may cause the material to
skim off if left uncovered. See reverse under application instructions.
VISCOSITY: *Colors or gloss may be affected by high humidity, low
temperatures, or chemical exposure.
Mixed= 500-1000 cps (typical) *For best results use a high quality 3/8”nap roller.
*Slab on grade requires moisture barrier.
FLEXIBILITY: *Substrate temperature must be 5°F above dew point.
*All new concrete must be cured for at least 30 days.
No cracks on a 1/8” mandrel *Physical properties are typical values and not specifications.
*Tire contact may cause staining and discoloration.
DOT CLASSIFICATIONS: * Slight appearances in gloss may vary from batch to batch,
therefore, use only product from same batch for an entire job.
Part A “Not regulated” *Lights like sodium vapor lights can cause discoloring.
Part B “Not regulated” * Always request a sample and apply a suitable test to determine
suitability and performance requirements before using.
*See reverse side for application instructions.
*See reverse side for limitations of our liability and warranty.

Care & Maintenance
Issue Date: 06/02/2015
Maintenance sealing will typically be needed from 6 months to 10 years depending upon environmental
conditions and usage. It is recommended that the surface be resealed when the sealer thickness falls
below 2 dry mils.
A technical representative or trained contractor can aid in determining reseal needs and maintenance
schedules.

245 Carl Karcher Way
Anaheim, CA 92801
Tel: 714-829-2600
WWW.GARAGECOATINGS.COM