Operating Instructions - Miele US

Cleaning and care

Cleaning the stainless steel Water container
milk flask
Change the water every day to prevent
(depending on the model) a build-up of bacteria.

The milk flask should be taken apart Make sure that the valve, the
and cleaned every day. underside of the water container and
the water container niche are clean.
^ Clean all parts by hand only using Otherwise the water container will
hot water and liquid dish soap. If not sit correctly.
necessary, a small brush can be
used to remove any stubborn milk ^ The water container can be cleaned
deposits. in the dishwasher or by hand using
hot water and liquid dish soap. After
^ Rinse all parts carefully under cleaning, dry the water container.
running water. Traces of dish soap
can affect the taste and quality of the ^ Clean the surface the water container
milk froth. Dry all parts thoroughly. sits on, particularly the slots,
carefully.
^ Reassemble the milk flask.

51

Cleaning and care

Drip tray cover Drip tray and waste container

^ Remove the drip tray cover from the Clean the drip tray and waste
drip tray. container every day every day to
avoid unpleasant smells and
^ The drip tray cover can be cleaned in mildew.
the dishwasher or by hand using hot
water and liquid dish soap. The waste container is located in the
drip tray.
^ Dry the drip tray cover thoroughly

The coffee machine will alert you via the
display when the drip tray and/or waste
container is full and needs to be
emptied. Empty the drip tray and the
waste container then.

^ Replace the cover onto the drip tray. TIP If the coffee machine has just been
Ensure that the milk tube aperture is rinsed, wait a while before removing the
on the left. drip tray. Rinse water will run out of the
coffee dispensers.

Drip tray

^ Push the coffee dispensers up as far
as they will go.

^ Remove the drip tray together with
the waste container by pulling the
drip tray forward.

^ Empty the drip tray and waste
container.

^ Clean the drip tray by hand using
warm water and liquid dish soap.
Clean the waste container, if
necessary (see "Waste container").

^ Dry the drip tray.

52

Cleaning and care

Make sure that the metal contact Waste container
discs on the drip tray are cleaned
and dried properly. The discs will The waste container will usually contain
not be able to detect that the drip some residual water from the rinsing
tray is full if they are dirty or damp. process

^ Clean the space under the drip tray. ^ Push the coffee dispensers up as far
as they will go.
^ Replace the waste container in the
drip tray and push the drip tray back
into the coffee machine.

Make sure the drip tray has been
pushed into its niche as far as it will
go.

^ Remove the drip tray together with
the waste container by pulling the
drip tray forward.

^ Empty the waste container and the
drip tray, if necessary. Used coffee
grounds should be disposed of with
organic waste or put on the compost
heap.

^ The waste container can be cleaned
in the dishwasher or by hand using
hot water and liquid dish soap. Clean
the drip tray, if necessary (see "Drip
tray").

^ Dry the waste container.

^ Replace the waste container in the
drip tray and push the drip tray back
into the coffee machine.

53

Cleaning and care

Bean container and ground Brew unit
coffee chute
Clean the brew unit by hand only
Disconnect the coffee machine from using hot water. Do not use soap.
the power supply before cleaning. The moving parts of the brew unit
are lubricated. Soap will damage the
TIP Use a vacuum cleaner to remove brew unit.
any dry coffee residues from the bean Clean the brew unit once a week.
container and the ground coffee chute.
Remove the brew unit and wash by
^ Open the lid on the right hand side of hand
the coffee machine. Remove the The brew unit can be removed for
coffee bean container lid. cleaning.
^ Pull out the two flaps on the right
^ Remove any coffee beans.
hand side of the coffee machine.
^ Clean the bean container with a dry, Turn the flaps 90° clockwise. Open
soft cloth. the door.

The coffee bean container can now be ^ Press the button on the end of the
refilled. handle of the brew unit a and while
doing so turn the handle
^ Replace the coffee bean container counterclockwise b.
lid.

If necessary, clean the ground coffee
chute:

^ Open the lid of the ground coffee
chute.

^ Remove any ground coffee.

^ Close the lid of the ground coffee
chute.

^ Close the lid on the right hand side of
the coffee machine.

54

Cleaning and care

^ Carefully pull the brew unit out of the To replace the brew unit, repeat the
coffee machine. previous steps in the reverse order:

If you cannot remove the brew unit ^ Push the brew unit back into the
easily, the brew unit is not in the correct coffee machine, making sure it is
position (see "Frequently asked straight.
questions").

After the brew unit has been
removed, do not alter the position of
the brew unit handle.
This would displace the brew unit
and it would not fit back into the
coffee machine.

^ Clean the brew unit by hand under ^ Press the button on the end of the
hot running water without soap. handle of the brew unit a and while
doing so turn the handle clockwise
b.

^ Close the door. Turn the flaps 90°
counterclockwise. Lower the flaps.

^ Wipe any coffee from the two filters.
One filter is located in funnel a and
the other to the left of funnel b.

^ Dry funnel area a to prevent ground
coffee sticking to it.

^ Clean the inside of the coffee
machine Use your vacuum cleaner to
remove dry coffee grounds.

55

Cleaning and care

Cleaning the brew unit TIP Place a suitable container
underneath the coffee dispensers. Then
Depending on the natural oil content of you don't have to empty the drip tray so
the coffee used, the brew unit can often.
become blocked quite quickly. Use the
cleaning tablets supplied to clean the When DROP CLEANING TAB IN
brew unit. GROUND COFFEE CHUTE appears:

These have been specially formulated ^ Open the lid on the right hand side of
for use in the coffee maker to optimize the coffee machine.
the degreasing. They are available
from Miele.

After 200 portions have been
dispensed, CLEAN THE BREW UNIT
will appear in the display. This
message will be displayed until the
cleaning program has been carried out.

The cleaning process takes about
10 minutes.

It is important to degrease the brew ^ Open the lid of ground coffee chute
unit regularly. a. Drop a cleaning tablet into
ground coffee chute b.
^ Press the OK button until MENU
appears in the display. ^ Close both lids.

^ Turn the rotary selector until ^ Follow the instructions given in the
MAINTENANCE appears in the display.
display.
Press the OK button. ^ When PROGRAM FINISHED appears
in the display, press the OK button.
^ Select CLEAN THE BREW UNIT and
press the OK button. The brew unit has now been
degreased.
^ Turn the rotary selector until START
appears in the display.
Press the OK button.

Follow the instructions about
degreasing the brew unit that appear in
the display.

56

Cleaning and care

Exterior

Remove any soiling promptly. The
surfaces can become discolored or
otherwise altered if soiling is not
removed right away.

Make sure that no water gets in
behind the display.

The exterior surfaces are
susceptible to scratching. Contact
with unsuitable cleaning agents
could cause discoloration.

Do not dry the mat surfaces of black
machines with a tea towel or similar.
The surface can become darker and
more shiny.

Ensure that any splashes during the
descaling process are wiped off im-
mediately.

^ Turn the machine off using the On/Off
button -.

^ Clean the housing with a clean, soft
sponge and warm water and liquid
dish soap.

57

Descaling

Limescale builds up in the coffee If the coffee system is hot, it will need to
machine during use. The limescale cool down for approx. 10 minutes
buildup in the machine will depend on before the descaling program can
the hardness of your local water supply. begin.
Limescale must be removed regularly.
TIP Place a suitable container
The machine will guide you through the underneath the coffee dispensers. Then
descaling process. Various instructions you don't have to empty the drip tray so
will appear in the display, e.g. you will often.
be prompted to empty the drip tray, fill
the water container, etc. Descaling following display
reminder
Descaling must be carried out. The
program takes approx. 30 minutes. ^ Press the OK button to start the
descaling program.
During the descaling program, water
containing descaling agent will run out The descaling program cannot be
of the hot water spout. This is followed canceled once is has started. The
by an activation period before a little program has to be carried through
more descaling agent is dispensed. to the end.

The coffee system will remind you when Descaling solution
the descaling program needs to be
carried out. NO. PORTIONS UNTIL The descaling tablets supplied have
DESCALING: 50 will appear in the been specially formulated for use with
display. The remaining number of this coffee machine. More descaling
drinks that can be made before tablets are available from Miele.
descaling will show in the display after
each drink is made. You will need one descaling tablet to
descale the machine.
^ Confirm the message with the
OK button. Only use the Miele descaling tablets
supplied. Other types of descaling
When 0 is reached the coffee system agents can damage the machine
will lock. START THE DESCALING and affect the taste.
PROGRAM will appear in the display.
^ Fill the water container to the "0.5 l"
You can turn the coffee machine off if mark with lukewarm water.
you do not want to run the descaling
program at this time. However, no more ^ Place 1 descaling tablet in the water.
drinks can be prepared until the
descaling program has been
completed.

58

Descaling

Be sure to mix water and descaling After descaling the machine carefully,
tablets in the right proportions. It is rinse the water container and the drip
important that you fill the water tray to remove all traces of descaling
container with enough water. Too agent.
little water can cause the descaling
program to be stopped prematurely. Selecting Descale from the
MAINTENANCE menu
^ Replace the water container in the
coffee machine. ^ Press the OK button until MENU
appears in the display.
Various messages will appear in the
display. ^ Turn the rotary selector until
MAINTENANCE appears in the
^ Follow the instructions given. display.
Press the OK button.
When FILL WATER CONTAINER AND
PLACE IN MACHINE appears in the ^ Select DESCALE and press the
display, OK button.

^ Rinse the water container carefully The following will appear in the display:
with clean water. Be sure that no
descaling agent is left in the water DESCALE
container. Fill the water container
with cold, clean tap water up to the r START s
"max." mark.
The descaling program cannot be
PROGRAM FINISHED will appear in the canceled once is has started. The
display when the descaling process program has to be carried through
has been completed. to the end.

^ Press the OK button. ^ Press the OK button.

^ Empty the drip tray. The descaling process will begin.

The descaling program is now
complete and drinks can be prepared
in the machine again.

When descaling the machine be
sure to wipe away any splashes of
descaling agent immediately. These
could damage the surfaces.

59

Energy saving mode

Eco-Mode Turning off

When using Eco Mode the coffee If the machine will not be used for an
system will save energy. extended period of time, turn it off using
the main switch at the back of the
The coffee system will switch to Eco machine.
mode if it has not been used to prepare
a drink in some time. When in Eco
mode the heat function is not on
constantly, therefore reducing energy
usage.

The coffee system will heat up again
when a drink is selected.

Pre-warming the cups with hot water

If you only need to pre-heat cups
occasionally, the cup warming surface
can be turned off.

Hot water from the cappuccinatore can
be used to pre-heat the cups instead.

60

Frequently asked questions

,Repairs should only be carried out by a qualified and trained person in

accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Do not open the outer casing of the coffee system.

You can easily resolve many of the minor problems yourself.
In some cases, an appropriate message appears in the display. To address the
fault, follow the instructions on the display.

Messages in the display

Message Possible cause and solution

FAULT - 1 The coffee machine has overheated.
FAULT - 2 ^ Turn the machine off with the On/Off - button. Wait
FAULT - 82
FAULT - 28 approx. one hour and then turn it on again.

FAULT - 73 ^ If the fault still appears, contact Miele Technical Service.

There is too much ready ground coffee in the ground
coffee chute.

If more than one level scoop is put into the ground coffee
chute the brew unit cannot process it. The ground coffee
will be directed into the waste container, and a Fault will
appear in the display.

^ Turn the machine off with the On/Off - button. Wait
approx. 2 minutes and then turn it on again.

The brew unit cannot be positioned correctly.

^ Turn the coffee system off using the main switch at the
back of the machine. After a few seconds turn the coffee
system back on.

^ Press the . and / buttons at the same time. Then press
the OK button twice.

This will initialize the brew unit motor and put in back into
the start position.
^ If the fault message appears in the display again,

contact Miele Technical Service.

61

Frequently asked questions

Message Possible cause and solution

FAULT - 74 ^ Turn the machine off and then back on again.
If the fault message appears in the display again,
^ contact Miele Technical Service.

The following The drip tray is not seated correctly
appears in the
display, even ^ Push the drip tray into the coffee system into it clicks into
though the drip tray place.
is empty:
or
EMPTY THE DRIP
The metal contacts are dirty.
TRAY ^ Clean and dry the contacts.

or

^ The drip tray sensor is not working correctly.

^ Turn the coffee machine off and then n again with the
main switch.

^ If the fault still appears, contact Miele Technical Service.

Noises can be The coffee system is trying to draw in water, even though
heard from the the water tank is empty. Air is present in the pipework.
pump and the ^ Fill the water container with cold, fresh tap water.
display shows:
SYSTEM FILLING UP - START will appear in the display.
FILL WATER ^ Press the OK button.
CONTAINER AND
PLACE IN THE
MACHINE

62

Frequently asked questions

Message Possible cause and solution

The following The water tank is not seated correctly.

appears in the ^ Remove the water container and then replace it.

display although the
water container is If the fault message appears in the display again,
full: ^ empty the water container.

FILL WATER
CONTAINER
AND PLACE IN
THE MACHINE

^ Check to see that the float moves freely, by shaking the
water container.

^ Fill the water container with fresh, cold tap water and
replace it in the coffee system.

If the fault still appears, contact Miele Technical Service.

Dispensing stops There is not enough water in the water container.
and the following ^ Fill the water container.
appears in the ^ Press the OK button.
display:

PROCESS STOPPED CONTINUE DISPENSING - YESB appears in the display.

WATER CONT. EMPTY

^ Press the OK button to continue dispensing,

or select NO to cancel the preparation.

63

Frequently asked questions

Message Possible cause and solution

The message The coffee machine needs descaling and/or the brew
unit filters are blocked.
SYSTEM
FILLING UP - START ^ Turn the machine off with the On/Off - button.

appears in the display ^ Press the OK button for 2 seconds and call up
again. MAINTENANCE - DESCALE.

^ Descale the coffee machine.

^ Remove the brew unit and rinse it under running
water (see "Brew unit").

If the fault message appears in the display again,

^ Degrease the brew unit (see "Cleaning the brew
unit").

If the fault still appears in the display, contact Miele
Technical Service.

The following message is The milk system was not rinsed prior to turning off last

displayed after turning time.

on: ^ Rinse the milk system (see "Rinsing the milk

RINSE THE system").

MILK SYSTEM

CLEAN THE MILK The milk system needs to be cleaned.
SYSTEM
^ Confirm this message by pressing the OK button.
appears in the display.
^ Clean the milk system (see "Cleaning the milk
system").

DEMO MODE IS ACTIVE The demo setting of the coffee machine for
showrooms or dealers has been activated.
or
^ Deactivate the demo mode (see "Demo mode").
DEMO MODE ACTIVE
FUNCTION DEACTIVATED
appears in the display.

64

Frequently asked questions

Unsatisfactory results

Problem Possible cause and solution

Water is dispensed The ground coffee chute lid was opened and closed
from the coffee without coffee being put into it. YES was then selected
dispensers when when the GROUND COFFEE option appeared in the
coffee has been display.
selected.
^ If ground coffee has not been added to the ground
coffee chute, NO must be selected when prompted to
use GROUND COFFEE.

or

Coffee beans have become stuck in the grinder

^ Turn the coffee machine off with the main switch.

^ Remove all coffee beans from the bean container. Use a
vacuum cleaner if necessary.

^ Add fresh coffee beans. Prepare a coffee drink.

Espresso or coffee The grind level is too coarse.

flows into the cup ^ Set the grinder control to a finer setting (see "Adjusting

too quickly. the grinder setting").

Espresso or coffee The grind level is too fine.

flows too slowly into ^ Set the grinder control to a coarser setting (see

the cup. "Adjusting the grinder setting").

65

Frequently asked questions

Problem Possible cause and solution

The coffee or The cup has not been pre-heated.
espresso is not hot ^ Pre-heat the cups (see "Pre-warming cups").
enough or
The brewing temperature is set too low.
^ Set a higher brew temperature (see "Brewing

temperature").
or
The brew unit filters are blocked.
^ Clean the brew unit (see "Brew unit").
^ Degrease the brew unit (see "Cleaning the brew unit").

The crema on the The grinder is not set correctly.
coffee or espresso ^ Set the grinder control to a coarser or finer setting (see
is "not right".
"Adjusting the grinder setting").

or

The brew temperature is too high for the type of coffee
being used.
^ Set a lower brew temperature (see "Brewing

temperature").

or

The coffee beans are no longer fresh.
^ Add fresh beans to the coffee bean container.

or

The coffee dispensers are too high.
^ Pull the dispensers down until they are at the same

height as the cup rim.

66

Frequently asked questions

Unusual performance of the coffee machine

Problem Possible cause and solution

When a drink is The brew unit filters are blocked.

selected very little or ^ Clean the brew unit (see "Brew unit").
nothing at all is

dispensed from the ^ Degrease the brew unit (see "Cleaning the brew unit").

coffee dispensers.

Water has stopped The maximum water quantity possible was reached.
flowing when Preparation is stopped and the max. portion size possible
programming the is saved.
amount.
or

There was not enough water in the water tank. The
programming process is canceled and the setting will not
be saved

^ Fill the water container.

^ Repeat the programming procedure.

The coffee machine This is not a fault.

does not rinse itself If the coffee machine still has an operating temperature
when turned on. higher than 140 °F (60°C), rinsing will not take place.

There is a lot of The grind level is too coarse.

"coffee water" in the ^ Set the grinder control to a finer setting (see "Adjusting
waste container. the grinder setting").

^ Adjust the amount of coffee, if necessary (see "Adjusting
the strength of the coffee").

67

Frequently asked questions

Problem Possible cause and solution

When the coffee The main switch is turned off ("0").

system is turned on ^ Set the main switch to on ("I").
using the - button the
display remains dark. or

The machine is not properly plugged into the outlet.

^ Insert the plug into the electrical outlet.

or

The circuit breaker has tripped due to a problem with the
coffee machine, the electricity supply or another
machine.
^ Remove the power plug from the electrical outlet.

^ Contact a qualified electrician or Miele Technical ser-
vice for assistance.

The display lights up The demo setting of the coffee machine for showrooms

but the coffee or dealers has been activated.

machine does not ^ Deactivate the demo mode (see "Demo mode").
heat up and no drinks

are prepared.

The coffee machine
cannot be turned off
with the On/Off button
-.

The coffee machine The programmed turn off time has been reached.
turns off suddenly. ^ If desired set a new turn off time (see "Timer").

or

The machine is not properly plugged into the outlet.

^ Insert the plug into the electrical outlet.

68

Frequently asked questions

Problem Possible cause and solution

The coffee machine The system lock is activated.

does not turn on at ^ Deactivate the system lock. See "System lock".
the programmed and

activated "Switch on or

at" time. The coffee system was not used after being turned on

three times in a row automatically.

^ Turn the machine on and prepare a drink.

or

Eco mode is activated. The timer function is not available
in this mode.
^ Select Comfort mode (see "Operating modes").

The grinder is louder The beans could contain stones.

than usual. ^ Turn the machine off immediately.

^ Contact Technical Service.

or

The coffee bean container has become empty during the
grinding process.

^ Fill the coffee bean container with fresh beans.

The grinder setting The control is blocked.
control will not move. ^ Prepare a coffee drink.

^ Reset the grinder setting while grinding is in progress.

Milk is dripping out of The level of milk in the milk flask is higher than the

the cappuccinatore cappuccinatore.

even though no milk ^ Push the coffee dispensers up as far as they will go.
is being dispensed.

^ Use a smaller milk flask if necessary.

69

Frequently asked questions

Problem Possible cause and solution

The brew unit cannot The brew unit or the brew unit motor is not in the correct

be removed, position. This can happen if the brew unit or the drip

or tray is pulled out while brewing is taking place.

the brew unit cannot be ^ Turn the machine off with the On/Off - button.

replaced in the coffee ^ Press the . and / buttons at the same time. Then
system
press the OK button twice.

This will initialize the brew unit motor and put in back
into the start position.

If the brew unit still cannot be removed or replaced in
the machine,
^ Contact Miele Technical Service.

The descaling program The descaling program cannot be canceled once the

was started OK button has been pressed.

unintentionally. The process must run through to completion. This is a

safety measure to ensure that the machine is fully

descaled. It is important for the long-term protection of

the machine and to ensure that it functions properly.

^ Complete the descaling program (see "Descaling".)

Loud noises are heard This is not a fault.

during the descaling These noises occur when water is flushed through the

program. machine at a high pressure.

The heating-up time is The coffee machine needs to be descaled.
longer than usual, the ^ Complete the descaling program (see "Descaling".)
amount of water being
dispensed is not right
and the coffee machine
is not performing
correctly.

70

After sales service

Repairs

In the event of a fault which you cannot
correct yourself please contact the
Miele Service Department by phone
number at the back of this booklet.

^ Please quote the model type and
number of your appliance.

These can be found on the data plate
located behind the drip tray inside the
coffee system.

71

Accessories

The following accessories are included
with your coffee system depending on
the model:
– Measuring spoon

for ground coffee
– Integrated cappuccinatore

as a spare part
– Cleaning tablets

to clean/degrease the brew unit
– Descaling tablets

for descaling the water pipework
– Test strips

to determine the water hardness
level
– Cleaning
brush for cleaning the milk tube
– Milk flask
for storing and keeping milk cool
longer

These products and other useful
accessories can be ordered on the
Internet at www.mieleusa.com.

72

Transport

If the coffee machine will not be used Caution! Danger of scalding and
for an extended period of time, e.g. burns. Hot steam will escape from
vacation, or will be transported over a the cappuccinatore.
long distance, the machine should be
prepared as follows. The evaporation process is complete
when the message goes out.
Please note:
^ Turn the machine off using the main
– Empty and clean the coffee bean switch
container
^ Clean the drip tray and waste
– Empty and clean the water container container.

– Evaporating the coffee machine The coffee machine is now ready to be
packed.
– Clean the drip tray and waste
container When you are ready to use the
coffee system again it will need to
– Pack the machine securely be filled with water (see "First steps
to use").
Evaporating the coffee
machine Packing

The coffee machine should be Only pack the machine in a clean,
evaporated before it is stored for a long dry environment.
period of time or transported any Residue of coffee grounds can
distance - particularly at temperatures cause scratches on surfaces.
below freezing. Coffee, milk and water residues can
cause bacteria build-up.
Evaporating the machine will remove all
traces of water from the system. This Use the original packaging including
prevents water and frost damage. Styrofoam to pack the coffee system.

^ Turn the machine off with the On/Off Keep the Operating Instructions in the
- button. box for future reference. That way they
are available when the coffee machine
^ Empty the water container. is used again.

TIP Place a suitable container
underneath the hot water spout.

^ Press the OK button.

^ Then press the k button twice.

The evaporation process starts, the
coffee machine heats up and DRAIN
THE SYSTEM appears in the display.

73

74

Installation instructions

Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.

Electrical connection

All electrical work should be – A longer cord should be arranged so
performed by a qualified electrician that it will not drape over the counter
in strict accordance with national top or table top where it can be
and local safety regulations. pulled on by children or tripped over.
Installation, repairs and other work
by unqualified persons could be Do not connect the appliance to a
dangerous. power inverter or directly to power
produced outside of the normal
Verify that the voltage, load and circuit electrical grid (i.e. direct solar or wind
rating information found on the data power source).
plate match the household electrical
supply. This data must match to Direct connection to such power
prevent damage to the coffee system. If sources can cause power surges and
in doubt, consult a licensed electrician. tripped breakers when the appliance is
turned on, and could damage the
appliance.

The data plate can be found behind the Do not connect the appliance to energy
drip tray inside the coffee system. saving plugs or outlets. The reduction
of power to the appliance caused by
The plug will fit in the outlet only one these devices will cause the appliance
way. If it does not fit, DO NOT use force to run hot and may damage it and/or
and DO NOT modify the plug in any shorten its usable life.
way. Contact a qualified electrician.
Do not operate any appliance with a
The socket should be located next to damaged cord or plug. Contact Miele
the machine and be easily accessible. Technical Service.

If the appliance is connected to the If there is any question concerning
electrical supply with an extension cord the electrical connection of this
please note: appliance to your power supply,
please consult a licensed electrician
– A short power-supply cord is to be or contact Miele’s Technical Service
provided to reduce risks resulting Department. See back page for
from becoming entangled in or contact information.
tripping over a longer cord.
WARNING:
– Always use care and exercise THIS APPLIANCE MUST BE
caution with using an extension cord. GROUNDED

– The marked electrical rating of the
extension cord should be at least as
great as the electrical rating of the
appliance.

– The extension cord should be a
grounding-type 3-wire cord.

76

Installation

Danger of overheating! If the coffee machine is installed in a
Ensure that there is sufficient niche, the minimum dimensions of the
ventilation around the coffee system. niche are:
Be sure the vents at the top of the
machine are not covered Height 20" (508 mm)
completely. Width 17 11/16" (450 mm)
Depth 21 7/8" (555 mm)
Danger of overheating. If the coffee
system is installed behind a cabinet ^ Position the coffee machine so that
door, it may only be used with the the front edge lines up with the front
door open. Do not close the cabinet edge of the niche.
door while the coffee system is in
use.

– Install the coffee system in a dry, well
ventilated room.

– The ambient temperature should be
between 50°F (10°C) and 90°F
(32°C).

– The coffee machine should be
installed on a water resistant,
horizontal surface.

– Be sure the vents at the top of the
machine are not covered completely,
e.g. with a dish towel.

77

Dimensions

78

Caring for the environment

Disposal of packing material Disposal of an old appliance

The cardboard box and packing Old appliances may contain materials
materials protect the appliance during that can be recycled. Please contact
shipping. They have been designed to your local recycling authority about the
be biodegradable and recyclable. possibility of recycling these materials.
Please recycle.
Ensure that the appliance presents no
Ensure that any plastic wrappings, danger to children while being stored
bags, etc. are disposed of safely and for disposal. Before discarding an old
kept out of the reach of children. appliance, unplug it from the outlet, cut
Danger of suffocation! off its power cord and remove any
doors to prevent hazards.
The original packaging can be used
to transport the coffee system.

79

Alteration rights reserved / 1512 M.-Nr. 09 319 110 / 00

INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.