TEBS4 Cables

Commercial Vehicle Systems PD-272-020

P r oDd uAc tTA TEBS4

Cables for Trailer EBS (TEBS4)

Doc. No. Y107795 (EN - Rev. 001)
August 2015

Function

Cables are used in trailer EBS systems to:

• provide electrical power to the components in the
system.

• communicate signals to the ECU from sensors
monitoring trailer characteristics.

• communicate control commands from the ECU to
modulators/modules to enable any required braking
intervention.

• communicate control commands from the towing
vehicle.

Power Supply Cables are used to distribute electrical
power from the towing vehicle to electrically powered
braking and auxiliary equipment on the trailer. The main
power supply to the trailer is through a plug or socket
according to ISO 7638. The ISO 7638 connection
carries the CAN signal from/to the towing vehicle and so the EBS Power Supply Cables also provide the CAN
signal to the ECU.

The cables are available in various lengths and are normally supplied with a bayonet connector to ensure easy
and safe connection.

Modular Cables / Wiring Harnesses are available in many configurations and are used to supply electrical signals
and power to auxiliary equipment including the external third modulator on 4S/3M systems.

Wheel Speed Sensor Cables are used to connect the ECU to the wheel speed sensors so that their wheel speed
signals can be sent. The wheel speed sensor is supplied with only a short length of cable and so will often require a
Wheel Speed Sensor Extension Cable to enable connection.

NOTES: The text in the ‘Comments’ columns describes the typical usage. Other connections are
possible for most cables.

- The document starts with details of power cables, then shows modulator cables, wheel speed
sensor cables and auxiliary cables.

Technical Features -40 °C to +80 °C

Operating Temperature Range:

See tables for other features.

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

1 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015
Colour Coding used in this document
YE Yellow
BK Black GN Green
BN Brown RD Red
BU Blue WH White

Other Documentation

For information on systems and components mentioned in this document please refer to:

ABS Relay Modulator Valves PD-200-200, Document No. Y011362
TEBS4 Brake Module PD-214-100, Document No. Y011366
Wheel Speed Sensors PD-261-000, Document No. Y011363
Pressure Sensor PD-262-200, Document No. Y095830
Deflection Sensor PD-264-200, Document No. Y095832
Cables for TEBS G2 PD-272-025, Document No. Y142784
Diagnostic Cables for Trailer ABS/EBS PD-272-030, Document No. Y107796
Diagnostic Cables for TEBS G2 PD-272-035, Document No. Y138839
Tyre Pressure Monitoring System (TPMS) PD-551-000, Document No. Y095833

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 2

Commercial Vehicle Systems TEBS4 PD-272-020

Doc. No. Y107795 (EN - Rev. 001) Cables for Trailer EBS (TEBS4)
August 2015

Pin Configurations

1 2 21
7 37
46
6 3 24 V coding
5 4 5

ISO 7638 Socket Pin 1 red Valve supply voltage ISO 7638 Plug
(24 V) Pin 2 black ECU supply voltage (24 V)
Pin 3 yellow ECU ground
Pin 4 brown Valve ground
Pin 5 white Warning lamp
Pin 6 white/green CAN-Hi
Pin 7 white/brown CAN-Lo

6 5 6 6 54 3 2 1 Deutsch Plug
7 4 57 7 8 9 10 11 12 Code ‘A’ (X1)
(Grey)
3 3
2 42

1 1

7-pin Bayonet Socket 7-pin Bayonet Plug

(ISO 7638 Power) (ISO 7638 Power)

Modulator connectors 6.3 6 54 3 2 1 Deutsch Plug
7 8 9 10 11 12 Code ‘B’ (X2)
4.2 4.3 6.2 2 (Black)

3

4.1 6.1 41

M24x1 Connector - Socket DIN72585 Bayonet SSoocckkeett DIN72585 Bayonet Plug
11--RReeleleaasseeVVaalvleve
4.1 - Coommmmoonn 66.1.1--RReeleleaasseeVVaalvlvee 22--CCoommmmoonn
4.2 - Reelleeaassee VVaallvvee 66.2.2--CCoommmmoonn 33--HHooldldVVaalvlvee
4.3 - Hoolldd VVaallvvee 66.3.3--HHooldldVVaalvlvee 44--nnoot tccoonnneecctetedd

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

3 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015
Cable Selection Guide - TEBS4 (typical systems) Auxiliary Cables pages 11 - 18

ISO 7638 Power & 24 V CAN Pad Wear Sensing
Cables - pages 5 - 10 Cables - pages 20 - 22

SR

ISO 7638

TEBS4 LAC

ISO 1185 SL
or
ISO 12098 Diagnostic Socket Wheel Speed Sensor Connection

Stop Lamp Cables - pages 8, 9, 16 Cables - page 19
Power
Cables-
pages 8 - 10

Input Cables
pages 13 - 15, 18

ISO 7638 Power & 24 V CAN Wheel Speed Sensor Connection
Cables - pages 5 - 10 Cables - page 19

SAR SR
TEBS4
ISO 7638 BR9234
SL
ISO 1185
or
ISO 12098

SAL

Stop Lamp Power 3rd Modulator
Cables - pages 8 - 10 Cables - pages 11 - 14, 18

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 4

Commercial Vehicle Systems TEBS4 PD-272-020
Doc. No. Y107795 (EN - Rev. 001)
August 2015 Cables for Trailer EBS (TEBS4)

Power Supply Cable Options

Tr a i l e r

Semi-trailer Drawbar or Centre-axle Trailer

ISO 7638 Connector direct to TEBS4 Brake Module

Cable K002294 (page 6)

ISO 7638 Connector only -

ISO 7638 Connector to TEBS4 Brake Module via intermediate connector

Cable EK3110 (page 6) Cable EK3115 (page 7)

either

ISO 7638 Connector Cable K002288 / 89 / K004775 (page 7) Cable K002288 / 89 / K004775 (page 7)
to intermediate connector + ISO 7638 Socket K002290 (page 23) + ISO 7638 Plug K002291K02(2p269adrgawieng 23)

or

Intermediate connector Cable K002286 (page 10)
plus to TEBS4 module Harness EK3108 (page 10)
Harness EK3101 (page 8)
(ISO 7638 only) Harness EK3100 / 07 (page 8, 9)
Harness EK3102 (page 9)
or Intermediate connector
plus to TEBS4 module
+ ISO 1185 connection

or Intermediate connector
plus to TEBS4 module
+ diagnostic socket

or Intermediate connector
plus to TEBS4 module
or + diagnostic socket
plus + ISO 1185 connection
Intermediate connector
to TEBS4 module
+ ISO 1185 connection
+ auxiliary socket

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

5 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015

Power Cable (for semi-trailers) with ISO 7638 Socket and X1 Connector

Ø54 46 1

Ø11,7 2
±0,2 10

12
11

1 RD 4,0 mm² 6

2 BK 1,5 mm² 9

3 YE 1,5 mm² 7

4 BN 4,0 mm² 4

L 5 WH 1,5 mm² 8

6 WH/GN 1,5 mm² 5

7 WH/BN 1,5 mm² 3

K002294 wiring

Part No. Type No. Cable length Comments
K002294 1) - L [m]

12.0

Power Cable (for semi-trailers) with ISO 7638 Socket

Ø54 Ø27,2

Ø11,7
±0,2

L

Part No. Type No. Cable length Comments
EK3110 L [m]
II367419000 Use with X1 Power Supply Harness
II3674115000 9.0 (pages 8 to 10)

15.0

PPoowweerr CCoonnnneeccttiinngg CCaabbllee -- ttoowwiinngg vveehhiiccllee ttoo ttrraaiilleerr

L

Ø60
max

Part No. Type No. Cable length Comments
K004098 1) EK3150 L [m]
With 7 pin connectors, for connecting ABS or EBS
1.0 - 4.0 With buckling protection

1) The part number will carry a suffix “N00” which defines that it is supplied without packaging. Example K004098N00

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 6

Commercial Vehicle Systems TEBS4 PD-272-020
Doc. No. Y107795 (EN - Rev. 001)
August 2015 Cables for Trailer EBS (TEBS4)

Power Cable (for drawbar and centre-axle trailers) with ISO 7638 Plug Ø27,2

Ø11,7
±0,2

Part No. Type No. Cable length L EK3115 drawing
L [m]
II397938000 EK3115 8.0 Ø11,7 Comments
II3979310000 ±0,2 Use with X1 Power Supply Harness
II3979312000 10.0
(pages 8 to 10)
12.0
Ø27,2
Power Cable without plug

Part No. Type No. Cable length L
L [m]
K002288 1) - 13.0 Comments
K002289 -
K004775 - 17.5 Use with separate ISO 7638 socket/plug (page 23)
and X1 Power Supply Harness (pages 8 to 10)
23.5

Power Connecting Cable

Ø27,2 Ø11,7 Ø27,2
±0,2

Part No. Type No. Cable length L
K010712 1) - L [m]
Comments
0.5 Adapter to connect TEBS G2 Power Cable to TEBS4

1) The part number will carry a suffix “N00” which defines that it is supplied without packaging. Example K010712N00

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

7 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015

X1 Power Supply Harness (ISO 7638 only) with Diagnostic Socket 1 L2 BK 1,0 mm² 10

L2 2 WH 1,0 mm² 1
3
Ø5,9 YE 1,0 mm²
±0,2 4 2

5

M30 x 1,5 12

L1 11

1 RD 4,0 mm² 6

2 BK 1,5 mm² 9

Ø39 3 YE 1,5 mm² 7
Ø34 ±0,3
4 BN 4,0 mm² 4

Ø9,8 5 WH 1,5 mm² 8
±0,2
6 WH/GN 1,5 mm² 5

L1 7 WH/BN 1,5 mm² 3

EK3101 wiring

Part No. Type No. Cable length Comments
II367381 L [m] L1 = power supply (ISO 7638)
L2 = diagnostic socket
EK3101 LL21 = 0.5 Use with Power Supply Cable (page 6 and 7)
= 4.0

X1 Power Supply Harness (ISO 7638 and ISO 1185) with Diagnostic Socket

L3 1 L3 BK 1,0 mm² 10
L2
Ø5,9 2 WH 1,0 mm² 1
±0,2 Ø5,9 3
±0,2 YE 1,0 mm²
4 2
Ø32
5 L2

1 BK 1,0 mm² 12

2 YE 1,0 mm² 11

M30x1,5 DIN 72585 3

Ø39 4 L1
1
RD 4,0 mm² 6

2 BK 1,5 mm² 9

3 YE 1,5 mm² 7

4 BN 4,0 mm² 4

5 WH 1,5 mm² 8

Ø11,7 6 WH/GN 1,5 mm² 5
±0,2
7 WH/BN 1,5 mm² 3
L1
EK3107 wiring
Cable length
Ø34 ±0,3 L [m]

Part No. Type No. Comments

LLL312 = 0.5 L1 = power supply (ISO 7638)
= 1.0 L2 = stop lamp supply (ISO 1185)
K007525 EK3107 = 4.0 L3 = diagnostic mountingBK 1,0 mm²
s12ocket (without YE 1,0 mm² kit)

Use with Power Su43pply Cable (page 6 and 7)

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 8

Commercial Vehicle Systems
Doc. No. Y107795 (EN - Rev. 001)
August 2015
M30 x 1,5

PD-272-020
TEBS4

Cables for Trailer EBS (TEBS4)

X1 Power Supply Harness (ISO 7638 and ISO 1185) with Diagnostic Socket (contd.)

L2 1 L2 BK 1,0 mm² 10
L3
2 WH 1,0 mm² 1
Ø11,7 3 2
4 YE 1,0 mm²
L ±0,2 12
Ø5,9 1 5 L3 YE 1,0 mm² 11
±0,2
6
BK 1,0 mm² 9
7
Ø39 1 L1 RD 4,0 mm² 4
Ø34 ±0,3 8
2 BK 1,5 mm² 5
3 YE 1,5 mm² 3
4 BN 4,0 mm²
5 WH 1,5 mm²
6 WH/GN 1,5 mm²
7 WH/BN 1,5 mm²

EK3100 wiring

Part No. Type No. Cable length Comments
II367391 L [m]
L1 = power supply (ISO 7638)
LLL231 = 0.5 L2 = diagnostic socket
= 4.0 L3 = stop lamp supply (ISO 1185)
= 1.0 Use with Power Supply Cable (page 6 and 7)

II367393 EK3100 LLL321 = 0.5
II367395 = 6.0
= 1.0

LLL231 = 0.5
= 4.0
= 12.0

II367397 LLL231 = 0.5
= 6.0
= 12.0

X1 Power Supply Harness (ISO 7638 and ISO 1185) with Auxiliary Socket (Aux 4)

L3 AUX 4 1 L3 BK 1,0 mm² 10
L2 GND 2
Ø5,9 3 YE 1,0 mm² 2
±0,2 Ø5,9 4
AUX 4 ±0,2 1
ISO 1185
L2 YE 1,0 mm²

BK 1,0 mm² 12

L1 11

1 RD 4,0 mm² 6
2
3 BK 1,5 mm² 9
4
5 YE 1,5 mm² 7
6
ISO 7638 7 BN 4,0 mm² 4
Ø34 ±0,3
WH 1,5 mm² 8

Ø11,7 WH/GN 1,5 mm² 5

L ±0,2 WH/BN 1,5 mm² 3

1 EK3102 wiring

Part No. Type No. Cable length Comments
L [m]

K002950 LLL231 = 0.5 L1 = power supply (ISO 7638)
= 12.0 L2 = stop lamp supply (ISO 1185)
= 6.0 L3 = auxiliary socket (Aux 4)
Use with Power Supply Cable (page 6 and 7)
K004754 EK3102 LLL132 = 0.5
= 1.0
= 4.0

K004756 LLL213 = 0.5
= 12.0
= 4.0

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

9 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015
X1 Power Supply Harness (ISO 7638 and ISO 1185)

L2 1

2
46 10

L2 YE 1,0 mm² 12

BK 1,0 mm² 11

1 L1 RD 4,0 mm² 6

2 BK 1,5 mm² 9

Ø11,7 3 YE 1,5 mm² 7
±0,2
4 BN 4,0 mm² 4
L1
Ø34 ±0,3 5 WH 1,5 mm² 8

6 WH/GN 1,5 mm² 5

7 WH/BN 1,5 mm² 3

EK3108 wiring

Part No. Type No. Cable length Comments
II40391F1 EK3108 L [m]
II40391F2 L1 = power supply (ISO 7638)
LL12 = 0.5 L2 = stop lamp supply (ISO 1185)
= 1.0 Use with Power Supply Cable (page 6 and 7)

LL12 = 0.5
= 12.0

X1 Power Supply Harness (ISO 7638)

1

46 2
10

12
11

1 RD 4,0 mm² 6

2 BK 1,5 mm² 9

Ø11,7 3 YE 1,5 mm² 7
±0,2
Ø34 ±0,3 4 BN 4,0 mm² 4
L
5 WH 1,5 mm² 8

6 WH/GN 1,5 mm² 5

7 WH/BN 1,5 mm² 3

K002286 wiring

Part No. Type No. Cable length Comments
K002286 1) L [m]
L = power supply (ISO 7638)
- 0.5 Use with Power Supply Cable (page 6 and 7)

1) The part number will carry a suffix “N00” which defines that it is supplied without packaging. Example K002286N00

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 10

Commercial Vehicle Systems TEBS4 PD-272-020
Doc. No. Y107795 (EN - Rev. 001)
August 2015 Cables for Trailer EBS (TEBS4)

X2 Connector Harness with Auxiliary Connector (Aux 1)

AUX 1 1 BK 1,0 mm² 1
GND 2 YE 1,0 mm² 12
3
Ø5,9 4 3
±0,2 4
5
AUX 1
Ø17,5 2
11
L
6
7
8

10
9

EK3123 wiring

Part No. Type No. Cable length Comments
EK3123 L [m]
II397882
II397883 4.0
II397884
6.0

2.0

X2 Connector Harness with Auxiliary Connector (3rd Modulator or Aux 1 & 2)

AUX 2 1 BK 1,0 mm² 2
GND 2 12
AUX 1 3 WH 1,0 mm² 1
4 YE 1,0 mm² 4
5
Ø5,9 3
±0,2 11
6
AUX 1 7
AUX 2 8
10
Ø17,5 9

L EK3142 wiring

Part No. Type No. Cable length Comments 1
K002954 L [m] for connecting 3rd modulator BR9234 12
3
EK3142 9.0 or 4
other Aux 1/2 devices 5
2
X2 Connector Harness with Auxiliary Connectors (Aux 1 and Aux 2) 11
6
L1 1 L1 BK 1,0 mm² 7
8
Ø5,9 2 YE 1,0 mm² 10
±0,2 3 9
4
EK3122 wiring
AUX 1 3 3 1 L2 BK 1,0 mm²

AUX 2 2 YE 1,0 mm²
3
4

Ø17,5 Ø5,9 L2
±0,2

Part No. Type No. Cable length Comments
II397874 EK3122 L [m]

LL12 = 6.0 LL21 = Aux 1
= 2.0 = Aux 2

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

11 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015

X2 Connector Harness with Auxiliary Connectors (3rd Modulator or Aux 1, Aux 2 and Aux 3)

L1 AUX 2 L1 BK 1,0 mm²
GND
Ø5,9 AUX 1 1 WH 1,0 mm² 2
±0,2 2
3 YE 1,0 mm² 12
4
1

AUX 1 4
AUX 2
9
Ø17,5
L2 10
BK 1,0 mm²
Ø27,2 AUX 3 1 3
AUX 3 GND 2
Ø5,9 3
±0,2 4 YE 1,0 mm² 11
5
5
L2 6
7
8

EK3140 wiring

Part No. Type No. Cable length Comments
K002951 L [m]
L1 = BR9234 or other Aux 1/2 devices
EK3140 L1 = 9.0 L2 = Aux 3 - bayonet splitter
L2 = 6.0

L1 AUX 2 1 L1 BK 1,0 mm² 2
GND 2
AUX 1 3 WH 1,0 mm² 12
4
YE 1,0 mm² 1

Ø5,9 4
±0,2
AUX 1 3 9
AUX 2 3
10
L2
AUX 3 1 BK 1,0 mm² 3
GND 2 YE 1,0 mm² 11
3
AUX 3 4 5
Ø17,5 6
Ø5,9
±0,2 L2 8
7

EK3141 wiring

Part No. Type No. Cable length Comments
K002952 L [m]
L1 = BR9234 or other Aux 1/2 devices
EK3141 L1 = 3.0 L2 = Aux 3
L2 = 6.0

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 12

Commercial Vehicle Systems TEBS4 PD-272-020
Doc. No. Y107795 (EN - Rev. 001)
August 2015 Cables for Trailer EBS (TEBS4)

X2 Connector Harness with Auxiliary Connectors and input cables

L2 GND 4 L1 YE 1,0 mm² 12
L1 AUX 1 3
2
1 BK 1,0 mm² 1

AUX 2 L2 BK 1,0 mm² 2
AUX 3 WH 1,0 mm² 3
AUX 1 3 3 GND
AUX 2 Ø5,9 YE 1,0 mm² 11
AUX 3 ±0,2 Ø5,9
Input A ±0,2 10
Input B
9
Part No.
Input A L3 BK 1,0 mm² 4
II397951 Input A_GND 5
YE 1,0 mm²
II397952 Input B 6
Input B_GND
AUX 1 L4 BK 1,0 mm² 8
AUX 2
L3/4 YE 1,0 mm² 7

EK3125 wiring

Type No. Cable length Comments
EK3125 L [m]
L1 = Aux 1
LLLL3214 = 4.0 L2 = Aux 2 & 3
= 1.0 L3 = Input A
= 1.0 L4 = Input B
= 1.0

LLLL4132 = 6,0
= 1,0
= 1,0
= 1,0

L1 AUX 2 L1 BK 1,0 mm² 2
GND
Ø5,9 AUX 1
±0,2

YE 1,0 mm² 12

WH 1,0 mm² 1

AUX 3 1 L2 BK 1,0 mm² 3
GND 2
AUX 3 3 YE 1,0 mm² 11
4
Ø5,9 10
±0,2
9

Input A L3 4
5
Input B Input A BK 1,0 mm²
Input A_GND
YE 1,0 mm² 6
Input B
L4 Input B_GND L4 BK 1,0 mm² 8
L3
YE 1,0 mm² 7
L2
EK3129 wiring

Part No. Type No. Cable length Comments
L [m]

LLLL1342 = 1.0 LLLL1423 = Aux 1 & 2 or BR9234
= 1.2 = Aux 3
K004569 EK3129 = 1.0 = Input A
= 1.0 = Input B

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

13 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015

X2 Connector Harness with Auxiliary Connectors and input cables (contd.)

L1 AUX 2 1 L2 BK 1,0 mm² 2
L2 GND 2
AUX 1 3 WH 1,0 mm² 12
Ø5,9 4
AUX 1 ±0,2 YE 1,0 mm² 1
AUX 2
AUX 3 3 3 AUX 3 1 L1 BK 1,0 mm² 3
Ø5,9 GND 2
±0,2 3 YE 1,0 mm² 11
4
10

9

Ø17,5 Input A L3 BK 1,0 mm² 4
Input A_GND 5
YE 1,0 mm²
Input A Ø5,9 Input B 6
±0,2 Input B_GND
L4
Ø5,9 BK 1,0 mm² 8
Input B ±0,2
YE 1,0 mm² 7
L4
L3 EK3126 wiring
EK3127 wiring
Part No. Type No. Cable length Comments
L [m]

II39802F1 EK3126 LLLL1342 = 2.0 LLLL3421 = Aux 3 2 or BR9234
= 6.0 = Aux 1 &
= 1.0 = Input A
= 1.0 = Input B

L1 GND 4 L2 YE 1,0 mm² 12
L2 AUX 1 3
2 BK 1,0 mm² 1
Ø5,9 1
±0,2
AUX 1 AUX 2 1 L1 BK 1,0 mm² 2
3 GND 2
AUX 2 Ø5,9 3 3 YE 1,0 mm² 11
±0,2 4
10

9

4

Ø17,5 3L3
Input A BK 1,0 mm² 5
Input A_GND
Input A Ø5,9 YE 1,0 mm² 6
±0,2 Input B
Input B_GND L4
BK 1,0 mm² 8
Ø5,9
Input B ±0,2 YE 1,0 mm² 7

L4
L3

Part No. Type No. Cable length Comments
II39814F1 EK3127 L [m]
II39814F2 L1 = Aux 2
LLLL3412 = 6.0 L2 = Aux 1
= 2.0 L3 = Input A
= 15.0 L4 = Input B
= 7.0

LLLL2134 = 6.0
= 2.0
= 6.0
= 6.0

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 14

Commercial Vehicle Systems PD-272-020

Doc. No. Y107795 (EN - Rev. 001) TEBS4
August 2015
Cables for Trailer EBS (TEBS4)

Connecting Cable for Aux 4 and Input C

L1

Ø5,9 Input C a L1 BN 0,75 mm² 3
±0,2 Input C_GND b
WH 0,75 mm² 5

Input C Ø5,9 L2
±0,2
AUX 4
Ø17,5 AUX 4 1 BK 1,0 mm² 1
GND 2
3 YE 1,0 mm² 4
4
L2

K002283 wiring

Part No. Type No. Cable length Comments
K002283 L [m] L1 = Input C
L2 = Aux 4
- L1 = 1.0 Used in conjunction with K002270/71/72
L2 = 3.0

Connecting Cable - Bayonet Splitter

L1 L1 BK 1,0 mm²

AUX 2 or 4 1 YE 1,0 mm² 1
GND 2
Ø17,5 Ø5,9 3 4
±0,2 4
AUX 2 AUX 4
or Ø5,9 AUX 3 or 5 1 L2 BK 1,0 mm² 3
oder ±0,2 GND 2
3
AUX 3 AUX 5 4 YE 1,0 mm² 5

Ø17,5 L2

K002284 wiring

Part No. Type No. Cable length Comments
K002284 L [m]

- L1 = 1.0 L1 = Aux 2 or Aux 4
L2 = 3.0 L2 = Aux 3 Aux 5

Used in conjunction with K002270/71/72

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

15 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015
Connecting Cable for Diagnostic Socket

1 BK 1,0 mm²

M30 x 1,5 Ø5,9 2 WH 1,0 mm²
±0,2 3 YE 1,0 mm²
4

5

Ø38.4 L

Part No. Type No. Cable length Comments K002270 wiring
K002270 1) L [m]
K002271 1) - 2.0 Diagnostic Socket without mounting kit
K002272 1) - or AUX 4 and Input C
- 6.0 or several AUX

15.0

Connecting Cable - Bayonet Splitter

Ø27,2 1 BK 1,0 mm²

Part No. Ø5,9 2
K002273 ±0,2
3 YE 1,0 mm²
4

L 5

Type No. Cable length Comments
L [m] Used in conjunction with K002285

K002273 wiring

- 6.0

Connecting Cable - 2 x reset to ride height outputs

Ø5,9 RTR-1 1 BK 1,0 mm² 1
±0,2 GND 2 YE 1,0 mm² 4
3
Ø5,9 4
±0,2

RTR-2 1 BK 1,0 mm² 2
GND 2 YE 1,0 mm² 5
3
Ø17,5 L 4

Part No. K002285 wiring
K002285
Type No. Cable length Comments
L [m]

- 0.5 Used in conjunction with K002273

1) The part number will carry a suffix “N00” which defines that it is supplied without packaging. Example K002272N00

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 16

Commercial Vehicle Systems TEBS4 PD-272-020
Doc. No. Y107795 (EN - Rev. 001)
August 2015 Cables for Trailer EBS (TEBS4)

Connecting Cable for auxiliaries (2 pins) AUX 1 1 BK 1,0 mm²
GND 2 YE 1,0 mm²
LØ5,9 3
4

Part No. Type No. Cable length Comments K002274-5-6
L [m]
K002274 1) - 2.0 with one end open (with pins to suit the
K002275 1) - Deutsch connector) for several AUX connections
K002276 1) - 6.5
K017003 1)
10.0

15.0

100 60 BK 1,0 mm²
YE 1,0 mm²
Part No. Signal
K002280 1) LØ5,9 GND
K002281 1)
Type No. Cable length Comments
L [m]
- with two ends open (one with pins to suit the
- 7.0 Deutsch connector) for several AUX connections

15.0 K002280-281 wir

1) The part number will carry a suffix “N00” which defines that it is supplied without packaging. Example K002281N00

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

17 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015
Connecting Cable for auxiliaries with Bayonet Connector (3 pins)

LØ5,9 AUX 2 1 BK 1,0 mm²
GND 2
AUX 1 3 WH 1,0 mm²
4 YE 1,0 mm²

Part No. Type No. Cable length Comments
L [m]
K002277 1) - 3.0 for 3rd modulator (BR9234) connection
K002278 1) -
K002279 1) - 9.0

15.0

Cable with open ends

100 Ø3,2 60 YE 1,0 mm²

L Comments
for Stop Lamp (for example)
Part No. Type No. Cable length K016629-30 wiring
K016629 1) - L [m]
K016630 1)
7.0

- 15.0

1) The part number will carry a suffix “N00” which defines that it is supplied without packaging. Example K016630N00

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 18

Commercial Vehicle Systems Ø16
Ø12,5
Doc. No. Y107795 (EN - Rev. 001)
August 2015 PD-272-020
TEBS4
Wheel Speed Sensor Extension Cable
Cables for Trailer EBS (TEBS4)

Ø5,9

L

Part No. Type No. Cable length Comments
EK3130 L [m]
II367562000 2.0 For extending the wheel speed sensor cable to enable
II367563000 3.0 connection to the brake module
II367564000 4.0
II367565000 5.0
II367566000 6.0
II367568000 8.0
II3675610000 10.0
II3675612000 12.0
II3675615000 15.0

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

19 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015
Pad Wear Sensing - Installation examples

to TEBS
module

K019786 K007202 K003848
or K007205
to TEBS
module

K019786 K007202 K007202 K003848
or K007205
to TEBS
module

K019786 K007202 K007217 K007202 K003848
or K007205 or

K007218
or

K007219

Note: further Axle Modules K007202 may be added as necessary

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 20

Commercial Vehicle Systems TEBS4 PD-272-020

Doc. No. Y107795 (EN - Rev. 001) Cables for Trailer EBS (TEBS4)
August 2015

Axle Module for Pad Wear Sensing

AC

L1 L1 K007202 K003848 2 x 0,5 mm² L1

Ø4,8 L2 K007202 K003848

L2 AC 2 x 0,5 mm² CA

2 x 0,5 mm² L1

CA K007202 wiring

Part No. Type No. Cable length Comments
K007202 - L [m]
K003848 -
LL12 = 2.0 LL12 = pad wear sensor cable
= 2.0 = connecting or extension

- Closure Cap for Axle Module K007202

Extension Cable for Pad Wear Sensing

Ø4,8 a BK 0,5 mm² a

L bb
WH 0,5 mm²
c c

Part No. Type No. Cable length Comments
L [m]
K007217 - 1.0 K007217 wiring
K007218 -
K007219 - 3.0 To connect two Axle Modules K007202 together

5.0

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

21 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015
Connecting Cable for Pad Wear Sensing

Ø5,9

a BK 0,75 mm² a

L b BN 0,75 mm² b
c

Part No. Type No. Cable length Comments
K019786 1) L [m] To connect Axle Module K007202

to TEBS Module K019786 wiring
(TEBS4 Module - SAL or SAR)
- 1.0

60 40

a BK 0,5 mm² a

b WH 0,5 mm² b
c

Ø5,9 Ø4,8

L

Part No. Type No. Cable length Comments K007205 wiring
K007205 - L [m]
To connect Axle Module K007202
1.0 to TEBS Module (Deutsch plug)

1) The part number will carry a suffix “N00” which defines that it is supplied without packaging. Example K019786N00

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 22

Commercial Vehicle Systems TEBS4 PD-272-020

Doc. No. Y107795 (EN - Rev. 001) Cables for Trailer EBS (TEBS4)
August 2015

Accessories

Part No. Type No. Description
K002290
- ISO 7638 Socket (7 pin)

Part No. Type No. Description
K002291 - ISO 7638 Plug (7 pin)

Blanking plug Part No. Type No. Description
wLLwooeeccddkkggiinenegg K002287 1) -
Part No. 12-pin Deutsch Plug
Blankinngg pplulugg K091439 1) (Code B for X2)
wLwLooeeccddkkggiinenegg
includes:
1 x Deutsch plug
1 x Locking wedge
12 x Blanking plugs

Type No. Description
- 12-pin Deutsch Plug

(Code A for X1)

includes:
1 x Deutsch plug
1 x Locking wedge
10 x Blanking plugs

Part No. Type No. Description

K026197V01 1) - Blanking Plug for
all Deutsch

12-way and 18-way
Sockets (no coding)

1) The part number will carry a suffix “N00” which defines that it is supplied without packaging. Example K026197V01N00

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

23 Knorr-Bremse Group

PD-272-020 TEBS4 Product Data
Doc. No. Y107795 (EN - Rev. 001)
Cables for Trailer EBS (TEBS4)
August 2015
Accessories (contd.)

Part No. Type No. Description
K005378 -
Mounting kit for
Diagnostic Socket

Revision Details

Rev. 000 March 2012 New document
Rev. 001 May 2015 Amended to include only TEBS4 cables. Obsolete part numbers deleted.
Rev. 001 August 2015 Correction to K091439..

The information contained herein is subject to alteration without notice and therefore may not be the latest release. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.
The figurative mark “K” and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com for full Disclaimer.
Note: If service work is carried out on a vehicle based on information provided herein, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full
functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
Copyright © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring.
Knorr-Bremse Systeme für Nutzfahrzeuge GmbH . Moosacher Straße 80 . 80809 Munich . Germany . Tel: +49 89 3547-0 . Fax: +49 89 3547-2767 . www.knorr-bremse.com . www.knorr-bremseCVS.com

Knorr-Bremse Group 24