DELIVERING INDUSTRY UNPRECEDENTED
POWER, PERFORMANCE, AND DURABILITY.
3/4" Heavy Duty AC Brushless Impact Wrench
WR22SE(G1)
Maintenance-free1 high performance 800W Brushless motor
– providing smaller more lightweight tool – only 4.6kg.
High performance 620Nm tightening torque
Stable Performance under voltage drop situations
– Unlike conventional electric Impact Wrenches, output torque isn’t
affected as much by voltage drops from long extension leads on site.
Stable Performance when used with Generators - Hitachi’s Brushless
Impact Wrenches operate consistently and without the traditional
problems cause by generator use2.
Heavy duty alloy body (AHB) for maximum durability,
superior rigidity and efficient heat dissipation.
F ront and rear rubber bumpers to protect tool and work material
R ocker switch provides quick switching between forward and reverse
Pin/retaining ring socket retainer system (pin and retainer not included)
Standard with side handle and carry case
1. B ecause the rotor has no coil or commutator there is no risk *Socket not included
of armature burnout, or the need to replace carbon brushes.
2. R equires suitably sized Generator output.
1" Heavy Duty AC Brushless Impact Wrench
WR25SE(G1)
Maintenance-free1 high performance 900W Brushless motor
– providing smaller more lightweight tool – only 7.7kg
H igh performance 1,000Nm tightening torque
Stable Performance under voltage drop situations
– Unlike conventional electric Impact Wrenches, output torque isn’t
affected as much by voltage drops from long extension leads on site.
S table Performance when used with Generators - Hitachi’s Brushless
Impact Wrenches operate consistently and without the traditional
problems cause by generator use2.
H eavy duty alloy body (AHB) for maximum durability,
superior rigidity and efficient heat dissipation.
Front and rear rubber bumpers to protect tool and work material
R ocker switch provides quick switching between forward & reverse
H anger – designed to be hung from a wire or rope to reduce user fatigue
P in/retaining ring socket retainer system (pin and retainer not included)
Standard with side handle and carry case
1. Because the rotor has no coil or commutator there is no risk *Socket not included
of armature burnout, or the need to replace carbon brushes.
2. R equires suitably sized Generator output.
Cordless Impact Wrenches For more information page 18-19
CAPACITY POWER NO-LOAD IMPACT TIGHTENING OVERALL
MODEL ORDINARY BOLT HIGH TENSION BOLT DRIVE INPUT SPEED MAX RATE MAX TORQUE LENGTH WEIGHT
WR22SE(G1) 14-24mm 16-22mm 3/4” square 800W 1,400/min 2,000/min 620Nm 280mm 4.6kg
WR25SE(G1) 22-30mm 22-24mm 1” square 900W 1,100/min 1,500/min 1,000Nm 340mm 7.7kg
Unless stated accessories pictured with products are not included as standard. 51
Torque Wrench should always be used for critical applications.
ANGLEGRINDERS
NEW 730W General Purpose Angle Grinders
G10SR4 / G12SR4 / G13SR4
A vailable in 100/115/125mm
Strong alloy gearbox
H eat resistant, high powered 730W motor
S pindle lock
E rgonomically angled side handle
Standard with grinding wheel, wrench, side handle and carry case
840W High Performance Angle Grinders
G12SN / G13SN
A vailable in 115/125mm
Strong alloy gearbox
High performance 840W motor with high overload durability
Spindle lock
E rgonomically angled side handle
Standard with grinding wheel, wrench side handle and carry case.
1200W 125mm Paddle Switch Angle Grinder
G13SE2
P owerful 1200W motor
Tool-less guard adjustment
Safe and easy-to-use paddle switch
L ow profile head
S pindle-lock and ergonomically angled side handle
Standard with grinding wheel, wrench and side handle
1300W 125mm Heavy Duty Angle Grinder
G13SB3
P ower and performance in a compact package
H eat resistant, super high powered 1300W motor
Sleek, low profile head
S trong alloy gearbox
S pindle lock and ergonomically angled side handle
Standard with grinding wheel, wrench and side handle
CAPACITY SPINDLE POWER NO-LOAD OVERALL
THREAD INPUT SPEED
MODEL WHEEL HOLE DIA. M10 x 1.5 LENGTH WEIGHT
M14 x 2
G10SR4 100mm 16mm M14 x 2 730W 10,000/min 254mm 1.4kg
G12SR4 115mm 22mm M14 x 2
G12SN 115mm 22mm M14 x 2 730W 10,000/min 254mm 1.4kg
G13SR4 125mm 22mm M14 x 2
G13SN 125mm 22mm M14 x 2 840W 10,000/min 259mm 1.6kg
G13SE2 125mm 22mm
G13SB3 125mm 22mm 730W 10,000/min 254mm 1.4kg
840W 10,000/min 259mm 1.6kg
1200W 11,000/min 321mm 1.9kg
1300W 11,000/min 283mm 1.9kg
Unless stated accessories pictured with products are not included as standard.
52
ANGLEGRINDERS
1200W 125mm Heavy Duty Angle Grinder
G13SC2
A n impressive 125mm grinder, extremely comfortable to operate
Sleek, low profile head
H igh-powered 1200w heat resistant motor
Deadman-type switch
3 -position side handle and spindle lock
Standard with grinding wheel, wrench and side handle
1200W 125mm Ergo Heavy Duty Angle Grinder
G13SW(G1)
A new generation Heavy Duty Angle Grinder featuring:
Advanced ergonomics resulting in new slim body design
– only 202mm diameter
New anti-vibration side handle and quick adjust tool-less guard
Increased overload and dust durability from new generation 1200W motor
N ew ultra compact gearbox design for better tight area access
S ide mounted switch design
Standard with grinding wheel, wrench and side handle
1500W 125mm Electronic Safety Grinder
G13YC2
Super-powerful 1500W motor with high overload durability
S afe and easy-to-use paddle switch
Strong alloy gearbox with spindle lock
Tool-less guard adjustment
Anti-vibration side handle
Fully-compliant electronic safety grinder featuring:
• Constant speed control • Soft-start control
• Overload protection • Kickback protection • Zero-voltage restart protection
Standard with grinding wheel, wrench and side handle
1500W 125mm Variable Speed Angle Grinder
G13VA
S uper-powerful 1500W motor with high overload durability
T ool-less guard adjustment
A nti-vibration side handle
Strong alloy gearbox with spindle lock
H igh performance electronic grinder featuring:
• Variable speed control • Constant speed control
• Soft-start control • Overload protection
• Zero-voltage restart protection • Kickback protection
Standard with grinding wheel, wrench and side handle
18.0V Angle Grinders For more information page 19 & 32
CAPACITY SPINDLE POWER NO-LOAD OVERALL
MODEL WHEEL HOLE DIA. THREAD INPUT SPEED
LENGTH WEIGHT
10,000/min
G13SC2 125mm 22mm M14 x 2 1200W 391mm 2.8kg
G13SW(G1) 125mm 22mm M14 x 2 1200W 12,000/min
277mm 2.3kg
10,500/min
G13YC2 125mm 22mm M14 x 2 1500W 323mm 2.0kg
G13VA 125mm 22mm M14 x 2 1500W 2,800-10,500/min
298mm 2.0kg
Unless stated accessories pictured with products are not included as standard.
53
ANGLEGRINDERS
2000W 230mm Industrial Angle Grinder
G23ST(G1)
Lightweight and compact new body design for general purpose use
N ew compact body design provides higher performance
in a slimmer body due to high magnetic flux density core motor
(the magnetic ‘pull’ of the rotating motor)
High-performance 2000W motor
L ow profile gearbox for easy access into tight areas
Best in class overload durability,
up 20% from previous model G23SS
N ew labyrinth air vent design provides
more protection for motor from grit
and dirt contamination
H alved stator coils for maximum cooling
efficiency, increasing motor durability
Standard with wrench and side handle
(supplied without pictured grinding wheel)
2200W 230mm Industrial Angle Grinder
G23SW2(G1)
Lightweight and compact new body design for general purpose use
New compact body design provides higher performance
in a slimmer body due to high magnetic flux density core motor
(the magnetic ‘pull’ of the rotating motor)
High-performance 2200W motor
Low profile gearbox for easy access into tight areas
Best in class overload durability,
up 20% from previous model G23SS
N ew labyrinth air vent design provides
more protection for motor from grit
and dirt contamination
H alved stator coils for maximum cooling
efficiency, increasing motor durability
S oft grip trigger handle
Standard with wrench and side handle
(supplied without pictured grinding wheel)
CAPACITY SPINDLE POWER NO-LOAD OVERALL
THREAD INPUT SPEED
MODEL WHEEL HOLE DIA. LENGTH WEIGHT
M14 x 2
G23ST(G1) 230mm 22mm 2000W 6,600/min 469mm 5.1kg
M14 x 2
G23SW2(G1) 230mm 22mm 2200W 6,600/min 469mm 5.1kg
Unless stated accessories pictured with products are not included as standard.
54
ANGLEGRINDERS
2400W Extra Heavy Duty Angle Grinders
G18MR / G23MR
Available in 180/230mm
2 400W motor with high overload durability
S uper tough alloy outer casing with
double-insulated polycarbonate inner layer
E asy to operate trigger switch
3-position anti-vibration side handle
Tool-less guard adjustment
L ow profile head for access into confined areas
A uto-stop brushes and anti-dust airflow
system for maximum motor protection
Standard with grinding wheel, wrench, wheel washer,
wheel nut, cut-off wheel mounting nut and side handle
2400W 230mm UVP Heavy Duty Angle Grinder
G23SEY
User Vibration Protection by vibration absorbing main and side handles
Coupling damper absorbs impact sound, 60% lower than previous models
2 400W motor with high overload durability
Easy to operate trigger switch
3-position anti-vibration side handle
Tool-less guard adjustment
L ow profile head for access into confined areas
A uto-stop brushes and anti-dust airflow
system for maximum motor protection
Standard with grinding wheel, wrench, wheel washer,
wheel nut, cut-off wheel mounting nut and side handle
ELECTRONIC CONTROLS: • Kickback protection - cuts power to the motor and stops
• Constant speed control - constant rotation speed is the power tool in the event of a sudden drop in wheel
maintained during operation, ensuring maximum efficiency. rotation speed during operation (eg. wheel locking during
cutting operation). This not only reduces operator strain
• Soft-start control - reduces the force generated at motor but is a significant safety feature, virtually eliminating
start-up, lessening the load on the operator’s hands.
the likelihood of the tool being flung out of the operator’s
• Variable speed control - enables the operator to select hands in the event of a ‘lock up’.
the appropriate rotation speed for each application, • Zero-voltage restart protection – disables motor start-up
ensuring maximum work efficiency.
when the switch is locked on and the power cord is
• O verload protection - shuts off power to the motor in the reconnected to the power, or when the power supply
event of motor overload or a sudden reduction in rotation recovers from power failure. This is another significant
speed during operation. This severely reduces the risk safety feature, eliminating accidents due to unplanned
of motor burnout and controller failure. motor restarts.
CAPACITY SPINDLE POWER NO-LOAD OVERALL
THREAD INPUT SPEED
MODEL WHEEL HOLE DIA. LENGTH WEIGHT
6,600/min
G23SEY 230mm 22mm M14 x 2 2400W 500mm 5.1kg
8,500/min
G18MR 180mm 22mm M14 x 2 2400W 492mm 5.4kg
6,600/min
G23MR 230mm 22mm M14 x 2 2400W 492mm 5.4kg
Unless stated accessories pictured with products are not included as standard.
55
DIEGRINDERS
6mm Die Grinder
GP2S2
S uper heavy duty unit
5 20W motor
H igh no-load speed of 29,000rpm
C ompact design for easy operation and significant reach
Standard with side handle,
6mm collet chuck and wrenches
6mm Variable Speed Die Grinder
GP3V
Heavy duty industrial unit
High speed model for small grinding wheels and specialist applications
Super powerful 760W motor
Variable speed range: 7,000 – 29,000rpm
Easy to grip slim body – only 200mm circumference
S oft Start and Constant Speed Control
Standard with side handle,
6mm collet chuck and wrenches
6mm Variable Speed Die Grinder
GP5V
Heavy duty industrial unit
Lower speed/high torque model for larger grinding wheels
Super powerful 760W motor
V ariable speed range: 2,000 – 8,300rpm
E asy to grip slim body – only 200mm circumference
S oft Start & Constant Speed Control
Standard with side handle,
6mm collet chuck and wrenches
10.8V Micro Li-ion Die Grinder GP10DL For more information page 39
CAPACITY POWER NO-LOAD OVERALL
INPUT SPEED
MODEL COLLET CHUCK MAX WHEEL DIA. LENGTH WEIGHT
GP2S2 6mm 25mm 520W 29,000/min 360mm 1.7kg
GP3V 406mm 1.8kg
GP5V 6mm 25mm 760W 7,000 - 29,000/min 406mm 1.9kg
6mm 50mm 760W 2,000 - 8,300/min
Unless stated accessories pictured with products are not included as standard.
56
SPECIALITYMETAL SAWS / CUTTERS
355mm Metal Cut-off Saw
CC14SF
P owerful 2000W motor
Quick release vice
S park diversion guide
Convenient spindle lock
Soft-grip handle
Capable of cutting shaped steel
up to 130 x 130mm
Standard with cut-off wheel and wrench
1.6mm Nibbler
CN16SA
P owerful 400W unit
N o-load speed 2300/min
C ompact, lightweight design
T hree-dimensional die holder for straight, right and left cutting
Downward cutting for high visibility and clean work
Standard with punch, die and 2x hex bar wrenches
Replacement Punch #998030
Replacement Die #998039
1.6mm Shear
CE16SA
Powerful 400W unit
N o-load speed 4700/min
Compact, lightweight design
S crap guard protects operators hands
R eplaceable blades have 8 cutting edges each
Standard with one pair blades, thickness gauge and hex bar wrench
Replacement Moving Blade #998000
Replacement Stationary Blade #998001
CAPACITY POWER NO-LOAD OVERALL
INPUT
MODEL WHEEL DIA. BAR DIA. PIPE DIA. SHAPED STEEL SPEED LENGTH WEIGHT
16.5kg
CC14SF 355mm 65mm 120mm 130mm x 130mm 2000W 3,800/min 603mm
WEIGHT
CAPACITY CUTTING MINIMUM POWER NO-LOAD OVERALL 1.6kg
1.7kg
MODEL STEEL STAINLESS WIDTH CUT RADIUS INPUT SPEED LENGTH
CN16SA 1.6mm (16 gauge) 1.2mm (18 gauge) 5mm 40mm 400W 2,300/min 250mm
CE16SA 1.6mm (16 gauge) 1.2mm (18 gauge) – 25mm 400W 4,700/min 250mm
Unless stated accessories pictured with products are not included as standard.
57
SABRESAWS
‘Godzilla’ UVP Sabre Saw
CR13VBY
U ser Vibration Protection through
reciprocating counter weight design
P owerful 1150W motor
U nique ‘swing’ action for faster cutting of most materials
O ne-handed, tool-less blade changing and tool-less shoe plate adjustment
S peed controlled by both a pre-set dial and the trigger switch
W ide variety of genuine Hitachi blades available and blades
can be mounted upside down to perform pocket cuts
Standard with blade and carry case
‘Godzilla’ Sabre Saw
CR13VB
Powerful 1050W motor
Unique ‘swing’ action for faster cutting of most materials
O ne-handed, tool-less blade changing and tool-less shoe plate adjustment
S peed controlled by both a pre-set dial and the trigger switch
R ubber, non-slip, front and rear hand grips
W ide variety of genuine Hitachi blades available and blades
can be mounted upside down to perform pocket cuts
Standard with blade and carry case
Sabre Saw
CR13V
P owerful 1010W motor
Compact and lightweight
R obust tool-less blade changing
E lectronic control with variable speed
Tough non-slip rubberised housing
W ide variety of genuine Hitachi blades available and blades
can be mounted upside down to perform pocket cuts
Standard with blade, wrench and carry case
10.8V Micro Li-ion Sabre Saw
CR10DL
V ariable speed
C ompact and lightweight
T ool-less blade change and adjustable front foot
L ED light to illuminate work area
Battery level warning light
W ide variety of genuine Hitachi blades available and blades
can be mounted upside down to perform pocket cuts
Standard with 1x 1.5Ah Li-ion battery, charger, 2x blades and carry case
18V Cordless Sabre Saw CR18DSLNN For more information page 33
For more information page 83
Replacement sabre saw blades
CAPACITY POWER NO-LOAD LENGTH OVERALL
MODEL PIPE STEEL WOOD INPUT SPEED OF STROKE LENGTH WEIGHT
CR13V 130mm 19mm 300mm 1010W 0-2,800/min 29mm 435mm 3.3kg
CR13VB 130mm 19mm 300mm 1050W 0-2,800/min 32mm 465mm 4.0kg
CR13VBY 130mm 19mm 300mm
1150W 0-3,000/min 32mm 465mm 4.4kg
CR10DL 25mm 4mm 50mm 10.8V 0-2,700/min 13mm 349mm 1.2kg
Unless stated accessories pictured with products are not included as standard.
58
Barrel-grip Jigsaw JIGSAWS
CJ110MVA Optional dust extraction
adapter #321591,
P owerful 720W motor
4 -stage orbital cutting action refer page 84 for full list
V ariable speed (by dial)
B ase tilt angle 45˚ left and right Optional dust extraction
N on-slip handle and ergonomically positioned controls adapter #321591,
R ugged nickel-plated cast alloy base plate
Q uick release blade change system refer page 84 for full list
B uilt-in blower redirects airflow from the fan
and blows dust away from the cutting area
R emovable dust extraction adaptor can be connected
to an external dust collector
Standard with blade, wrench, splinter guard,
chip cover, dust collector adaptor and carry case
Jigsaw
CJ90VST
P owerful 705W motor
V ariable speed (by dial)
Tool-less blade change system
4 -stage orbital cutting action
D urable aluminium front casing
N ickel-plated alloy base plate
B ase tilt angle 45° left and right
Standard with blade, wrench and carry case
Jigsaw
CJ65V3
L ightweight and versatile
65mm capacity in timber
Base tilt angle 45˚ left and right
Chip cover and splinter guard for added safety
Soft-grip handle for easy operation
Can be connected to an external dust collector
Standard with blade, wrench, splinter guard and chip cover
18V Cordless Jigsaw CJ18DSLNN For more information page 28
For more information pages 83, 92-93
Replacement jigsaw blades
CAPACITY MIN. CUTTING POWER NO-LOAD LENGTH BASE OVERALL
SPEED OF STROKE TILT LENGTH
MODEL WOOD STEEL RADIUS INPUT WEIGHT
45° Left/Right 197mm 1.5kg
CJ65V3 65mm 6mm 25mm 400W 0-3,000/min 18mm 2.2kg
45° Left/Right 228mm 2.2kg
CJ90VST 90mm 8mm 25mm 705W 850 - 3,000/min 20mm
45° Left/Right 264mm
CJ110MVA 110mm 10mm 25mm 720W 850 - 3,000/min 26mm
Unless stated accessories pictured with products are not included as standard.
59
MULTITOOL Variable speed control
6,000-20,000opm with Auto Mode
350W Premium Multi Tool (15,000 - 20,000opm as required)
CV350V
The new standard in professional Multi Tools
S uper heavy duty 350W motor
H igh Oscillation Speed for faster cutting, but unique new design produces
low vibration back to the operator
H itachi’s unique AUTO mode automatically increasing or decreasing cutting
speed as required depending on the job – providing optimum performance
and control for any application
V ariable Speed control: 5 stage manual settings, plus AUTO mode
ss accessory changeC onstant Speed electronic monitoring ensures selected RPM
is maintained under load (manual mode)
S oft start to ensure operator is in complete control on start up
m makes accessory change more secureR eliable and simple tool-less blade change –
uses industry standard OIS blade system
Standard with 12 pce Accessory set (blades, sanding pad,
sandpaper, blade storage box), and carry case
Standard accessory set includes:
1 x Bi-Metal plunge cut saw blade (335881)
1 x Bi-Metal segment saw blade (335880)
1x Sanding plate (335903)
9 x Assorted grit sanding papers
Accessory storage box
Optional dust extraction adaptor #337922 refer page 84 for full list
Easy Tool-less Accessory changing
1 Insert the tool shaft 2 Pull down and turn 3 Close the lever
the sleeve cap to lock the accessory.
Sleeve Cap
Lever
after placing an accessory to align the lock mark
onto the attachment ring. with the triangle mark.
1 Insert the tool shaft
after placing an accessory
onto the attachment ring.
Tool Shaft Tool Shaft Tool Shaft
essories Multi-angle setting MultpTi ahlanecgesleletaoedvpjeursectvmaepennthtiot lfdrosmandraocpcpeisnsgoaryndin
ools at every 30˚ in 360˚ at evdearym3a0g°ining3a6n0y° work pieces during the
changing process.
* M ake sure that you follow the steps in the right order. If you take step 3 before Step 2, the accessory will not be mounted properly.
inal * P hoto shown with a cordless model CV18DBLNN. For more information page 34
e Dual mode settings:
1S8tVanBdruasrdhleMsosdMe ualntidTAoUoTl COVM18odDeBLNN
60
oad Standard Mode OSCILLATION POWER NO-LOAD SPEED NO-LOAD SPEED OVERALL
NORM. MODE (DIAL: 1-5) AUTO MODE (DIAL: A) LENGTH
MODYEouL can change the oscAilNlatGioLnEfr equency betwINeePnUT WEIGHT
CV3560,0V0 0/min and 20,000/min3b.2y˚ dial. 6,000 - 20,000/min 15,000 <==> 20,000/min 280mm 1.5kg
350W
AUTO Mode*1 Unless stated accessories pictured with products are not included as standard.
Depending on the workload, the oscillation frequency is changed automatically
from 15000/min or 20000/min.
Mode Dial Oscillation Frequency
CIRCULARSAW
NEW C6MEY 165mm AC Brushless Circular Saw
with Deep Cut design – cuts the same depth as a 185mm saw
Hitachi continues to develop
and expand its range of high
performance AC Brushless models.
Key Benefits
Overload Protection
Electronic control circuit automatically
switches the saw off in the event of
a jam.
AC Brushless Motor Silent Mode
Ideal for applications
Hitachi’s World-First AC Brushless in noise-sensitive
Motor Technology brings a whole areas, such as
new level of performance and renovation and
durability to this Heavy Duty interior work.
range of power tools. The Silent Mode lowers the noise
Extreme Durability by reducing the max motor RPM.
With no carbon brushes or commutator in- Conventional commutator motor When the load increases during the
side the tool, major wearing parts have been Silent Mode, the operating mode
eliminated from the motor – meaning less automatically switches to Power
wear and tear, and less maintenance. The Mode, enabling smooth cutting
Brushless motor will last up to three times according to the conditions.
longer than conventional brushed motors.
Maximum Power Automatically switches
Hitachi’s AC Brushless Motors operate far
more efficiently than conventional brush motors – The silent mode reduces the RPM to 2,500/min,
delivering more power and less energy consumption.
Generator Compatible resulting in 5dB less noise level!
Unlike conventional tools, Hitachi’s AC Brushless Motor models aren’t
affected by poor power output from portable generators or the voltage drop (in comparison with the Power Mode)
effect created by long extension leads – meaning more reliability on site.
Built-in LED Light
See page 62 for full specifications. Effectively illuminates the work area
to be cut.
Unless stated accessories pictured with products are not included as standard. Cordless /
AC Twin Design
Identical in design to 18V cordless
model C18DBAL. Users can seamlessly
switch between tools with no loss
of functionality.
61
CIRCULARSAWS
185mm Super High Powered Circular Saw
C7SB2
F or extra heavy-duty applications Optional dust extraction
S uper high-powered 1710w motor adapter #303377,
R ugged alloy base that is easily recalibrated
High-tech magnesium gear case and guard reduces weight refer page 84 for full list
and improves strength
Anti-slip handle and large front grip for excellent control
Spindle lock
0–55˚ bevel adjustment
Standard with TCT blade, wrench, guide and carry case
165mm Circular Saw
C6SS
P owerful 1050W motor
C ompact and lightweight at just 3.2kg
C ast aluminium base
E rgonomic handle
E ffective dust ejection Optional dust extraction
O n-board wrench storage adapter #302981,
Standard with TCT blade, wrench and guide refer page 84 for full list
NEW 165mm AC Brushless Circular Saw
C6MEY(G1)
Industry first high efficiency AC Brushless motor
165mm blade with deep cut configuration – max cut 66mm at 90°
Hitachi’s unique Silent mode allows for quieter operation
S mallest in class and well-balanced
Q uick and easy blade change
Resistant to voltage drop Optional parallel guides:
C ompatible with engine generators and overload protection 250mm #316161
650mm #316104
Standard with blade and wrench
185mm Dustless Circular Saw
C7YA
With a growing awareness about the need to work safely with fibre cement
products, this multi-purpose saw is just one more innovative solution from Hitachi.
Powerful 1400W motor
Designed for use with a special Polycrystalline Diamond Saw Blade
Capable of achieving 90% dust collection when connected to an external dust extractor
D ust can either be deflected out to the side via a chute,
collected on-board in a dust bag, or externally via a dust extractor
C an be used with a standard blade for wood cutting
R obust nickel-plated base plate
Standard with dust bag, dust chute and wrench (supplied without blade)
CAPACITY MAX. CUT MAX. CUT POWER INPUT NO-LOAD OVERALL WEIGHT
MODEL BLADE DIA. DEPTH 90˚ DEPTH 45˚ /VOLTAGE SPEED LENGTH
C6SS 165mm 57mm 38mm 1050W 5,500/min 276mm 3.2kg
C6MEY(G1) 1050W 4,100/min / 2,500/min (silent) 262mm 2.8kg
165mm 66mm 45mm
C7SB2 185mm 60mm 47mm 1710W 5,800/min 305mm 4.6kg
C7YA 185mm 60mm 47mm 1400W 5,500/min 299mm 4.9kg
Unless stated accessories pictured with products are not included as standard.
62
CIRCULARSAWS
190mm Deep Cut Circular Saw
C7UY
D eep cutting depth: 7 8mm at 90˚ THE 7 1/2” SAW 78mm
55mm at 45˚ THAT CUTS Cutting Depth
AS DEEP
C ompact and lightweight AS AN 8 1/4”
H igh speed cutting
F ine parallel adjuster
P TFE coated base for smooth
sliding on work-pieces
E asy cutting depth adjustment
Easy access bevel adjustment
B lower function to clear saw dust
Standard with TCT blade, wrench, guide and carry case
Additonal optional accessories available:
dust extraction adapter #997247, guide rail adaptor #331762,
guide rail clamp #744200, guide rail joiner #744202
and 1400mm guide rail #744199, refer page 80 for full list
190mm Circular Saw Optional dust extraction
adapter #302981,
C7MFA
refer page 84 for full list
Lightweight and durable, this circular saw offers
rugged performance with high-quality cutting finish.
Industrial all ball bearing motor
L arge easy grip handle
P ositive spindle lock
Excellent cutting depth at 90˚: 68mm)
S trong, nickel plated, alloy base plate
Standard with TCT blade, wrench and guide
NEW 235mm Circular Saw
C9SA3
High performance, heavy duty model
New Aluminium saw cover
N ew blower function
4 m long cord
Powerful 2000W motor
Standard with TCT blade, wrench, guide and side handle
Optional dust extraction
adapter #303930,
refer page 84 for full list
CAPACITY MAX. CUT MAX. CUT POWER INPUT NO-LOAD OVERALL WEIGHT
MODEL BLADE DIA. DEPTH 90˚ DEPTH 45˚ /VOLTAGE SPEED LENGTH 4.2kg
3.6kg
C7UY 190mm 78mm 55mm 1300W 5,500/min 333mm 7.0kg
C7MFA 190mm 68mm 46mm 1010W
C9SA3 235mm 86mm 65mm 2000W 5,500/min 291mm
5,000/min 397mm
Unless stated accessories pictured with products are not included as standard.
63
MITRESAWS
NEW 305mm
Slide Compound
Mitre Saw
C12RSH2
N ew lighter weight design
C ompact slide system with large cutting capacity
P roven belt drive system for safety and durability
603mm wide base for extra stability
P owerful 1,520W motor
Sliding sub-fence to support large work pieces
L aser marker accurately indicates cutting position
D ual bevel “ left / right 45 degrees
P ositive stops for quick mitre angle setting
Standard with TCT blade, dust bag, vice assembly and wrench
Optional dust extraction adapter #308506,
refer page 84 for full list
Compact slide Saw head
system with large in the front
cutting capacity position
features a fixed rail slide design that Saw head 890mm
eliminates the need for rear clearance in the full IN DEPTH
to accommodate the extension of the back position
sliding rails.
This system allows the saw to sit up
against a wall or to be placed in tight
work areas, without compromising
cutting capacity.
Universal Mitre Saw Stand
UU750 * Includes adaptor
for – C10FSB,
Suits Hitachi and most other Mitre Saws C10FSH, C10FCE2
Q uick fit saw mounting for ‘four point’ style saws*
Dual extension arms – extends to 2.9m
F olds to a compact size for easy transportation
Adjustable work supports with rollers for easy material handling
CUT CAPACITY COMPOUND BLADE POWER MITRE BEVEL
45˚ x 45˚ DIAM. INPUT ANGLE ANGEL
MODEL CROSS MITRE BEVEL DIMENSIONS WEIGHT
C12RSH2 120x260mm 107x220mm 70x312mm (45˚ L) 70x220mm 305mm 1520w L: 0-45˚ L: 0-45˚ 655 x 890 x 724mm 27.0kg
107x312mm 45x312mm (45˚ R) R: 0-45˚ R: 0-45˚
Unless stated accessories pictured with products are not included as standard.
64
MITRESAWS
262mm
Slide Compound
Mitre Saw
C10FSH – with laser guide
C10FSB – without laser guide
P owerful 1450W motor with soft
start and electronic speed control
E lectronic overload protection
automatically switches saw off
in the event of a jam
H itachi’s belt drive design for smooth long lasting
operation and increased cutting capacity
M itre and bevel cut left and right, compound cut, trench and groove
A djustable laser guide accurately indicates cutting line (C10FSH)
C ompact and lightweight – weighs just 19.5kg
Standard with TCT blade, dust bag, vice assembly and wrench
Optional dust extraction adapter #308506, refer page 84 for full list
305mm Compound Mitre Saw
C12LCH
L ightweight & ultra-compact 305mm unit
Powerful 1520W motor
LCD display accurately indicates mitre and bevel angles to 0.5˚
Adjustable laser guide accurately indicates cutting line
Mitre and bevel cut left and right, plus compound cut
Standard with TCT blade, dust bag, vice assembly and wrenches
Optional dust extraction adapter #308506, refer page 84 for full list
255mm Compound Mitre Saw
C10FCE2
L ightweight & compact design – weighs just 12kg
P owerful 1520W motor
M itre cut left and right, bevel cut left, plus compound cut
Standard with TCT blade, dust bag, vice assembly and wrenches
Optional dust extraction adapter #308506, refer page 84 for full list
CUT CAPACITY COMPOUND BLADE POWER MITRE BEVEL
45˚ x 45˚ DIAM. INPUT ANGLE ANGEL
MODEL CROSS MITRE BEVEL L: 0-45˚ DIMENSIONS WEIGHT
L: 0-52˚ 460 x 628 x 561mm 12.0kg
C10FCE2 59x144mm 59x102mm 41x144mm 41x102mm 255mm 1520w R: 0-52˚ L: 0-48˚
89x101mm R: 0-3˚ 625 x 775 x 610mm 19.5kg
L: 0-52˚
C12LCH 61.5x200mm 61.5x140mm 40x200mm 40x140mm 305mm 1520w R: 0-52˚ 525 x 1050 x 615mm 19.5kg
96x155mm
C10FSH / C10FSB 90x312mm 100x220mm 60x280mm (45˚L) 60x220mm 262mm 1450w L: 0-45˚ L: 0-45˚
100x295mm 35x280mm (45˚ R) R: 0-57˚ R: 0-45˚
Unless stated accessories pictured with products are not included as standard.
65
SPECIALITYSAWS & CUTTERS SS10B
185mm Dustless Circular Saw
C7YA
With a growing awareness about the need to work safely with fibre cement products,
this multi-purpose saw is just one more innovative solution from Hitachi.
Powerful 1400W motor
Designed for use with a special
Polycrystalline Diamond Saw Blade
C apable of achieving 90% dust collection when connected
to an external dust extractor
Dust can either be deflected out to the side via a chute,
collected on-board in a dust bag, or externally via a dust extractor
C an be used with a standard blade for wood cutting
R obust nickel-plated base plate
Standard with dust bag, dust chute and wrench (supplied without blade)
Fibre Cement Snapper Shear
SS10A / SS10B
Capable of slicing through up to 16mm thick medium
density fibre cement board, the Snapper Shear is
the fast, low-dust solution for your fibre cement
cutting requirements. As well as impressive straight
line performance, the Snapper Shear will also cut
accurate notches, gentle curves, and clean internal
corners with ease. The Snapper Shear’s unique blade design allows
blades to be reversed when the cutting edge is worn out, extending
the life of the blades. When the second cutting surface wears out, the
blades can be swapped side for side, and then finally reversed again
— extending the life of one set of blades three times.
SS10A – High speed cutting (powered by D13VL drill)
SS10B – Slow speed, high torque option (powered by D13VG drill)
110mm Tile/Concrete Cutter
CM4SB2
High powered 1320W motor
Max cutting depth of 34mm (max 20mm per cut)
C ompact and versatile
E fficiently cuts bricks, tiles and concrete
Standard with dry-type diamond wheel and wrenches
CAPACITY POWER NO-LOAD OVERALL
MODEL BLADE WHEEL DIA. MAXIMUM CUT DEPTH INPUT SPEED LENGTH WEIGHT
C7YA 185mm 90˚ – 60mm, 45˚ – 47mm 1400W 5,500/min 299mm 4.9kg
SS10A – 16mm 860W 0-1000/min 390mm 3.2kg
SS10B – 16mm 800W 0-600/min 370mm 3.5kg
CM4SB2 110mm 34mm (max. depth 1 cut 20mm) 1320W 11,500/min 204mm 2.8kg
Unless stated accessories pictured with products are not included as standard.
66
SPECIALITYSAWS & CUTTERS
305mm Disc Cutter
CM12Y
A great alternative to a petrol cutter — without all the noise and fumes.
Superbly balanced for effortless cutting
Powerful 2400W motor with soft start
Adjustable guard for different cutting angles
D ust collection port for connection to dust extractors Optional dust extraction
Bore size 25.4mm or 22mm adapter #963558,
Standard with wrench (supplied without blade) refer page 84 for full list
125mm Concrete/Fibre Cement Cutter
CM5SB
A safe, versatile solution for fibre cement re-cladding tasks.
Efficient dust extraction when used with vacuum attachment
Tool-less depth adjustment for quick changes when
making multiple passes or to avoid cutting below a sheet
T ool-less cover removal allows access to quickly
remove and replace blades
Powerful 1300W motor with high overload durability
S pindle lock for quick and easy wheel changes
Standard with side handle, hose adaptor,
wrench, and carry case (supplied without blade)
Optional accessories
3.5m Anti-static dust extraction hose #15325
230mm Concrete Cutter
CM9SR
Efficient dust extraction when used with vacuum attachment
Tool-less depth adjustment for quick changes
when making multiple passes
E asy to read and convenient depth gauge
W ide base for stability with steel guide wheels
Powerful 2000W motor with high overload durability
S pindle lock for quick and easy wheel changes
Standard with D-handle, hose adaptor,
wrench, and carry case (supplied without blade)
Optional accessories
3.5m Anti-static dust extraction hose #15325
75.0cc Petrol Disc Cutter CM75EBP(GA) Refer to the Outdoor Power Equipment Catalogue
CAPACITY POWER NO-LOAD OVERALL
MODEL BLADE WHEEL DIA. MAXIMUM CUT DEPTH INPUT SPEED LENGTH WEIGHT
CM12Y 305mm 100mm (max. depth 1 cut 50mm) 2400W 5,000/min 633mm 11.5kg
CM5SB 125mm 30mm (max. depth 1 cut 15mm)
1300W 11,000/min 314mm 2.9kg
CM9SR 230mm 60mm (max. depth 1 cut 30mm) 2000W 6,600/min 615mm 7.7kg
Unless stated accessories pictured with products are not included as standard.
67
ROUTERS
½" Variable Speed Plunge Router
M12VE
Variable speed with electronic soft start
and constant speed control
Powerful 2000W motor
Unique depth adjustment – enabling fast,
more accurate depth settings
3 stage pre-set depth settings
Fully adjustable handles
Robust alloy base plate with polycarbonate insert
O ptional dust extraction port
Standard with ½" collet, straight guide,
template guide and wrench (supplied without cutter)
ROUTER ACCESSORIES
TEMPLATE GUIDES (FIT ALL HITACHI ROUTERS)
CODE OUTSIDE INSIDE CODE OUTSIDE INSIDE
DIAMETER DIAMETER DIAMETER DIAMETER
303347 9.5mm 7.5mm 956932 20.0mm 18.5mm
303350 12.0mm 10.1mm 303354 24.0mm 22.5mm
303351 12.7mm 10.7mm 956933 27.0mm 25.5mm
303352 14.0mm 12.0mm 956934 30.0mm 28.5mm
303353 16.0mm 14.0mm 303355 40.0mm 38.5mm
956790 18.0mm 16.5mm
Optional dust extraction adapter #997466, refer page 84 for full list
½" Plunge Router
M12SE
P owerful 1700W motor
U nique depth adjustment – enabling fast, more accurate depth settings
3 stage pre-set depth settings
Fully adjustable handles
Robust alloy base plate with polycarbonate insert
Optional dust extraction port
Standard with ½" collet, straight guide, template guide and wrench (supplied without cutter)
Optional dust extraction adapter #997466, refer page 84 for full list
¼" High Performance Plunge Router
M8SA2
Powerful 900W motor
Unique depth adjustment – enabling fast, more accurate depth settings
3 stage pre-set depth settings
F ully adjustable handles
R obust alloy base plate with polycarbonate insert
O ptional dust extraction port
Standard with ¼" collet, straight guide, template guide and wrench (supplied without cutter)
Optional dust extraction adapter #997466, refer page 84 for full list
CAPACITY POWER NO-LOAD
MODEL INPUT SPEED
COLLET CHUCK STROKE WEIGHT
M8SA2
M12SE ¼" 60mm 900W 25,000/min 3.5kg
M12VE 1700W 22,000/min 5.3kg
½" 65mm 2000W 8,000 - 22,000/min 5.3kg
½" 65mm
Unless stated accessories pictured with products are not included as standard.
68
PLANERSAND THICKNESSER
82mm High Performance TCT Planer
P20SF Optional dust extraction
adapter #334502,
P owerful 620W motor
M ax cutting depth 2.6mm and rebate up to 9mm refer page 84 for full list
H igh cutting speed – 34,000 cuts per minute
P recise depth adjustment
A utomatic safety stand to protect blades and surfaces
C onvenient cable deflector hook
Standard with mini reversible TCT blades, wrench, guide and robust carry case
82mm TCT Planer
P20ST
D ouble sided TCT blades Powerful 580W motor
H eavy Duty Alloy Base Plate P recise depth adjustment Optional dust extraction
adapter #334502,
M ax cutting depth 1.5mm and rebates up to 9mm
refer page 84 for full list
Standard with mini reversible TCT blades, wrench and parallel guide
82mm Rebate Planer
P20SA2
When extra cutting capacity is required, this is the tool for the job.
‘Power plus’ 720w motor C omfortable D-type handle.
Easy height adjustment A well-balanced and compact planer
Max cutting depth 3.0mm and rebate up to 25mm
Standard with mini reversible TCT blades, wrench and guide
330mm Planer Thicknesser
P13F
The P13F Thicknesser offers high performance for both jobsite and workshop
applications. Supplied with its own separate stand, the unit includes innovative
features such as dual position adjustment controls to suit both left and right
handed operators,a cutting head position lock and optional dust collection facility.
R ollers on the top provide easy return of workpiece to the front for the next pass
B uilt-in tool storage
C rank handle can be mounted on either side of unit for left or right handed users
C utting depth control setting
L arge depth scale
Powerful 1800W motor with overload protection
Long extension table with roller for better support and smooth feed
Pre-set 1/4”, 1/2”, and 3/4” depth gauge allows operator to plane Optional dust extraction
workpiece to precise thickness without having to measure adapter #303022,
S upplied with heavy duty stand refer page 84 for full list
18V 82mm TCT Planer P18DSLNN For more information page 35
Replacement planer blades For more information page 82
CAPACITY POWER NO-LOAD OVERALL
MODEL WIDTH DEPTH REBATE HEIGHT BED SIZE INPUT SPEED LENGTH WEIGHT
P20SF 82mm 2.6mm 9mm – – 620W 17,000/min 296mm 2.5kg
P20ST 82mm 1.5mm 9mm – – 580W 17,000/min 296mm 2.5kg
P20SA2 82mm 3.0mm 25mm – – 720W 14,000/min 309mm 3.0kg
P13F 330mm 2.4mm – 3.2 - 152.4mm 330 x 918mm 1800W 9,250/min – 46.0kg
Unless stated accessories pictured with products are not included as standard.
69
SANDERSAND POLISHERS
1/3 Sheet Orbital Sander
FSV10SA
P owerful 180W motor Optional dust extraction
C ompact and lightweight adapter #963558,
L ow noise design
C omfortable soft grip and larger trigger refer page 84 for full list
Standard with dust bag and perforator
¼ Sheet Orbital Sander
SV12SG
P owerful 200W motor
C ompact and lightweight
L arge soft grip, non-slip handgrip Optional dust extraction
Top-class dust collection adapter #963558,
Standard with dust bag and perforator refer page 84 for full list
½ Sheet Orbital Sander
SV12SD
D ust resistant design increases motor life
E fficient dust collection
F lush sanding on 3 sides
Direct drive system for minimum vibration and smooth finishing
Lever action, quick paper clamp system Optional dust extraction
adapter #300082,
Standard with dust bag and perforator
refer page 84 for full list
125mm Random Orbital Sander
SV13YB
P owerful 230W motor Optional dust extraction
H ook and loop pad adapter #963558,
C ompact and lightweight
Large soft grip, non-slip handgrip refer page 84 for full list
High dust collecting performance
Standard with dust bag
150mm Random Orbital Sander
SAY150A
Powerful 380W motor
A ccepts 150mm self-adhesive pads
D ust collection shroud for connection to dust extractors
Heavy duty alloy gear housing Optional dust extraction
adapter #963558,
Standard with side handle and wrench
refer page 84 for full list
CAPACITY ORBIT POWER NO-LOAD SPEED NO-LOAD SPEED OVERALL WEIGHT
MODEL PAD DIA. INPUT (SPINDLE) (ORBIT) LENGTH
FSV10SA 92 x 184mm 2.0mm 180W 10,000/min 20,000/min 184mm 1.3kg
SV12SG 110 x 100mm 1.5mm 200W 14,000/min 28,000/min 137mm 1.1.kg
SV12SD 114 x 228mm
2.4mm 300W 10,000/min 20,000/min 300mm 2.8kg
SV13YB 125mm 3.2mm 230W 12,000/min 12,000/min 145mm 1.4kg
SAY150A 150mm
7.0mm 380W 7,000/min 7,000/min 279mm 2.1kg
Unless stated accessories pictured with products are not included as standard.
70
SANDERSAND POLISHERS
76mm Variable Speed Belt Sander Optional dust extraction
adapter #963558,
SB8V2
refer page 84 for full list
P owerful 1020W motor
H eavy duty all-ball-bearing construction and long life drive belt
F lush compact design with clear sanding belt cover
Soft grip and well positioned handles
V ariable belt speed: 250-450M/min
B elt position visible through transparent cover
Standard with dust bag
Improved flush edge for cornerwork Variable belt sanding speed dial Clear cover for checking belt position
180mm 2-speed Sander/Polisher
SAT180
Heavy duty dust resistant design
P owerful 750W motor
2 -speed switch for sanding or polishing
Standard with side handle, wrenches, rubber pad and woollen bonnet
180mm Variable Speed Sander/Polisher
SP18VA
P owerful 1250W unit
C ompact and lightweight
Electronic control giving soft-start, constant speed control
and electronic overload protection
Twin variable speed controls – dial-up speed selector to pre-set
maximum speed for particular job, and variable speed trigger
S pindle lock for easy changing of rubber pad
User-friendly loop handle (can be fitted with
a traditional side handle if preferred)
Standard with side handle, wrenches, rubber pad and woollen bonnet
CAPACITY POWER NO-LOAD OVERALL
INPUT SPEED LENGTH WEIGHT
MODEL BELT PAD
SB8V2 76 x 533mm – 1020W 250 - 450m/min 318mm 4.3kg
SAT180 – 180mm 750W 1,900/3,400/min 395mm 2.9kg
SP18VA – 180mm
1250W 0 - 3,400/min 415mm 2.8kg
Unless stated accessories pictured with products are not included as standard.
71
NAILERS
90mm Framing Nailer
NR90AD
Light but powerful air nailer, drives up to 90mm D-head nails with ease
Tool-less depth adjustment
Single action nailing operation
Capable of driving 3 nails per second
Strong alloy magazine capable of holding up to 74 nails
Optional Adjustable Nail Gun Hanger available 60605X
Standard with safety glasses
APPLICABLE NAIL SIZES (mm)
L 50 - 90
d 2.9 - 3.8
D 6.8 - 7.7
50mm Brad Nailer
NT50AE2
Easily fires up to 50mm 18 gauge C1 brads
Tool-less depth adjustment
S lim nose for excellent vision when accuracy is critical
O pen nose design for quickly clearing jams
Durable magazine capable of holding up to 100 nails
Adjustable exhaust direction
Standard with safety glasses, wrenches and carry case
APPLICABLE NAIL SIZES (mm)
L 16 - 50
d 1.2
18V Stapler
N18DSLNN
Tool-less depth adjustment
Anti-blank firing protection
Compact & Lightweight
150 staple capacity with low level window
Suitable staples in 6-13mm length:
- RAPID 23/ Series
- RAPID SUPER STRONG 9/ Series
S upplied without batteries or charger
Standard with safety glasses and carry case
AIR DRIVING MAGAZINE AIR
MODEL
INPUT SPEED CAPACITY INLET DIMENSIONS WEIGHT
NR90AD 70 - 120 psi 3 nails/sec 74 nails NPT 3/8 thread 462 x 322mm 3.2kg
NT50AE2 NPT 1/4 thread 254 x 233mm 1.0kg
MODEL 70 - 120 psi 3 nails/sec 100 nails VOLTAGE OVERALL LENGTH WEIGHT
CAPACITY (STAPLE LENGTH) CAPACITY (MAGAZINE)
N18DSLNN 6-13mm 150 staples 18.0V 235mm 1.8kg
Unless stated accessories pictured with products are not included as standard.
72
BLOWERSAND HEAT GUNS
Blower / Extractor
RB40VA
High volume and variable speed
Air volume 0-3.8m³/min
Compact and lightweight
Capable of blowing and dust collection
Innovated design that allows for stationary applications
Standard with nozzle and dust bag
18V Blower
RB18DSLNN
Hitachi’s cordless blower is a compact and lightweight unit that
can be used in a variety of cleaning and inflation applications.
Powerful blow and air volume flow
Variable Speed 0-15,000/min
C apable of up to 31 minutes continuous use with 5.0Ah battery
Standard with nozzle. Battery and charger sold separately.
Dual Temp Heat Gun
RH600T
S witch for dual temperature output and airflow control
Cold air shot for fast cooling
O verheating protection
Ergonomic design with soft grip for comfortable extended use
Standard with carry case and 5 piece accessory pack to maximise
the versatility of the Hitachi Heat Gun:
S craper (for paint etc. once the surface has been heated)
G lass Shield (when working around window frames – shields the glass from excessive heat
C urved Nozzle – to provide even heat around pipes, tubes etc.
R ound Nozzle – to provide concentrated heat on a small spot
Flat Nozzle – for a wider, flat heat flow across a flat surface
Variable Heat Gun
RH650V
L CD digital display
Variable continuous temperature output control, 50-650°C
Constant temperature control for continuous use without overheating
E rgonomic design with soft grip for comfortable extended use
Standard with carry case and 5 piece accessory pack to maximise
the versatility of the Hitachi Heat Gun:
Scraper (for paint etc. once the surface has been heated)
G lass Shield (when working around window frames – shields the glass from excessive heat
Curved Nozzle – to provide even heat around pipes, tubes etc.
Round Nozzle – to provide concentrated heat on a small spot
F lat Nozzle – for a wider, flat heat flow across a flat surface
AIR AIR POWER INPUT NO-LOAD OVERALL
MODEL VOLUME SPEED LENGTH
PRESSURE TEMPERATURE / VOLTAGE WEIGHT
0-16,000/min 447mm 1.7kg
RB40VA 0-3.8m3/min 0 - 5.5 kPa – 550W 0.57kg
– 245mm 0.79kg
RH600T 250/500L/min – 450˚/600˚C 2000W
– 250mm
RH650V 250-500L/min – 50˚ - 650˚C 2000W
Unless stated accessories pictured with products are not included as standard.
73
DEMOLITIONHAMMERS
NEW SDS Max
Brushless Demolition Hammer
H45MEY
High performance AC brushless motor –
resistant to voltage drop and poor generator output
8.5J high demolition performance
AHB Design (Aluminium Housing Body)
UVP feature (User vibration protection)
Standard with bull point, adjustable side handle and carry case
NEW SDS Max
Brushless Demolition Hammer
H60MEY
H igh performance AC Brushless motor –
resistant to voltage drop and poor generator output
20 Joule high demolition performance
AHB Design (Aluminium Housing Body)
U VP feature (User Vibration Protection)
Standard with bull point, adjustable side handle and carry case
Demolition Hammer bits and accessories For more information page 87
IMPACT ENERGY POWER FULL-LOAD BIT OVERALL WEIGHT
MODEL PER STROKE INPUT IMPACT RATE SHANK LENGTH 7.3kg
12.2kg
H45MEY 8.5J 1150W 1,430-2,850/min SDS MAX 480mm
H60MEY 20.0J 1500W 1,500-2,100/min SDS MAX 585mm
Unless stated accessories pictured with products are not included as standard.
74
DEMOLITIONHAMMERS
NEW 45.0J Heavy Duty
Demolition Hammer
H65SB3
4 5 Joules of impact energy
G rease-packed lubrication system and triple dust seal design ensuring long service life
User Vibration Protection – (UVP)
Fitted with auto-stop brushes for maximum motor protection
Capable of demolishing 338kg of concrete in 30 minutes
– 18% higher performance than previous model
Shock absorbing handle and adjustable side handle with soft grip
Heavy duty Aluminium Housing Body (AHB)
E asy to transport wheeled carry case
Wide range of accessories available
Warratah/Marquee Peg Driver
Earthing Rod Driver
Rammer Plate
Clay spade
Standard with bull point, adjustable side handle and carry case with wheels
Demolition Accessories
FOR H65SB3 PART NO. SIZE (mm) FOR SDS MAX PART NO. SIZE (mm)
Bull Point 751543 410 313471 280
Cold Chisel 401990 410 Bull Point 313472 400
Cutter 751545 410 x 75 313473 280
Scoop Cold Chisel 313474 400
(Clay Spade) 319298 380 313475
Warratah/ Cutter 400 x 50
Marquee 797012 51mm Scoop 313476
Peg Driver PART NO. 400
13mm (ID FOR H90SG 985230 SIZE (mm)
Earthing Diameter) Bull Point 985231
Rod Driver Cold Chisel 985232 520
797013 Cutter 520
Scoop 985233 520 x 72
(Clay Spade)
546
Full Range of Demolition Hammer accessories can be found on page 87
IMPACT ENERGY POWER FULL-LOAD BIT OVERALL WEIGHT
MODEL PER STROKE INPUT IMPACT RATE SHANK LENGTH 18.0kg
H65SB3 45.0J 1340W 1,400/min 30mm HEX 731mm
Unless stated accessories pictured with products are not included as standard.
75
DEMOLITIONHAMMERS
70.0J Demolition Hammer
H90SG(G1)
B est in class demolition performance
70 Joules of impact energy
C apable of demolishing 512kg of concrete in 30 minutes
User Vibration Protection through an optimized hammering
mechanism, shock-absorbing construction and
vibration-absorbing handles
Improved handling with soft grip
handles and large lever switch
A luminium Body and internal double-insulation
construction for significantly enhanced durability
Standard with wrench.
Bull point not included.
Best in Class
IMPACT ENERGY 70J
H90SG
H90SE 55J
70J Impact energy
U p to 27% higher impact energy2
DEMOLITION PERFORMANCE (kg/30min.)
H90SG 512kg
H90SE 349kg
512kg/30min. demolition performance
U p to 47% higher demolition performance2
User Vibration Protection
An optimised hammering mechanism,
shock-absorbing construction and
vibration-absorbing handles
T ri-Axial Vibration Value 7.7m/s2
Approx. 54% lower vibration2
1 Optimised hammering mechanism 2 Shock-absorbing construction 3 Vibration-absorbing handles
A Front Cover B
Handle damper
Holder (B)
Secures sufficient air cushion and improves Front dampers (A) and (B) on the front Handle shaft Holder (A)
hammering movement, decreasing piston cover mount reduce
reaction force generated during hammering. vibration from an accessory tool.
And vibrations are significantly reduced by
making the piston and other parts lighter. Reduced vibration from the main unit
by means of four handle damper bent
by the rotating holder (A).
IMPACT ENERGY POWER FULL-LOAD BIT OVERALL WEIGHT
MODEL PER STROKE INPUT IMPACT RATE SHANK LENGTH
H90SG(G1) 70.0J 2000W 1,000/min 28.5mm HEX 860mm 32.0kg
Unless stated accessories pictured with products are not included as standard.
76
ACCESSORIES
HI-TORQ™ Impact Rated Bit Kits
HI-TORQ™ Impact Rated Driver Bit Kits - designed for use
in heavy duty applications with Hitachi Cordless Impact Drivers
Specified for the Oceania market – kits include SHOCK RESISTANT
Square Drive, Torx, and metric sockets DESIGN
Impact Rated magnetic bit holders
Impacted rated bits have been subjected to a HOT COLD
HARDENING process to provide greater durability
New Heavy Duty storage cases and pouches to provide
better security for these premium driving accessories
18pc HI-TORQ™ 35pc HI-TORQ™
Impact Rated Impact Rated
Driver Bit Set Driver Bit Set
728698 728699
INCLUDES INCLUDES
P hillips, Slot and Square bits • Phillips, Square and Torx bits
• M etric Magnetic Nut Setters
Magnetic Compact • M agnetic Bit Holder
Screw Guide • Robust Stackable Storage Case
3pc Impact Driver NEW 12pc
Adaptor Set Sabre Saw
Blade Roll
751970
402153
INCLUDES
1 2 assorted blades,
1 /4” Hex to 1/4” Square driver from 18TPI metal to
1 /4” Hex to 3/8” Square driver 6TPI wood and progressive
1/4” Hex to 1/2” Square driver
5pc SDS+ Jigsaw
Drill Bit Set Starter Pack
751024 750049
INCLUDES INCLUDES
2 x 6mm, 2 x 8mm, 1 x 10mm 1 0pc Jigsaw Blade Pack
Supplied in reusable 1 0 assorted blades from
hard plastic case 6TPI wood to 24TPI metal
Genuine SDS+
Made in Germany
200pc Die Grinder 389pc Die Grinder
Accessory Set Accessory Set
753948 753949
Compatible with the GP10DL and Compatible with the GP10DL
other mini die grinders with 3.2mm and other mini die grinders
collets. An assortment of pieces with 3.2mm collets.
including diamond cutters, grinding
wheels, sanding discs stainless An assortment of pieces
steel brushes and others. including diamond cutters,
grinding wheels, sanding discs
stainless steel brushes and others.
Unless stated accessories pictured with products are not included as standard.
77
ACCESSORIES
NEW 100pc Driver NEW Ratchet Screwdriver
Bit Set: 25mm - SQ2 with 10 Driver Bits
402334 402519
C ases can be stacked by screw-shaped bottom P rofessional quality ratcheting
Impact rated S2 driver bit for professional use screwdriver
Plastic case with handle 3 position ratchet (clockwise, counter-
clockwise, and locked ratcheting)
NEW 11pc Driver Bit Set D river bits stored in the built-in
gripof the screwdriver for
402329 convenient access
M agnetic bit holder in tip secures
Impact rated driver bits - the bits for added convenience
can be used for impact drivers B i-material, non- slip grip handle
for comfort and maximum torque
1/4” hex screw driving bits 4 x Phillips #2 C ontains 11x 25mm S2 colour-
coded 1/4” hex bits: Phillips,
3 x Square #2 3 x Hexagon #5 Pozi, Slot, Hex, Torx
S 2 material bits and bit holder are 42pc Driver Bit Kit
magnetised for easier catching of screws
710000
1 x 60mm stainless steel magnetic
bit holder (groove position: 9.5mm) Includes
Torx, Square, Philips,
11pc Driver Bit Kit Pozi and Hex bits
M agnetic bit holder
713000 Q uick fit drill bits
H ex sockets
Includes
P hilips, Pozi and Square bits 17pc Drill & Driver Set
M agnetic bit holder
728118G
71pc Driver Bit Set
Includes
741991 B lack & Gold Drill Bits
Phillips, Slot and Square bits
Includes Magnetic Compact
P hillips, Pozi, Hex, Screw Driving Guide
Square, Torx and Slot bits
Magnetic bit holder 112pc Driver Bit Kit
L ocking quick change bit holder
705315
45pc Drill & Driver Set
INCLUDES
115006 H SS, masonry, brad point and
spade drill bit sets
INCLUDES M etric and imperial sockets
Drill Bits Quick change chuck
S pade Bits 2 80mm flexible drive shaft
Phillips, Pozi, Slot, C ountersink
Square, Torx and Hex bits Philips, pozi, torx and square drive bits
N ut Drivers
M agnetic Bit Holder 41pc Impact
Socket/Driver Bit Kit
1/2” Impact Socket Set
752500
751879
INCLUDES
INCLUDES 1 0 Impact Sockets (8-22mm)
1 0mm, 11mm, 12mm, Socket Adaptors
13mm, 14mm, 17mm, 28 Assorted Driver Bits
19mm, 21mm, 22mm, 24mm
S upplied in tough steel case Unless stated accessories pictured with products are not included as standard.
78
ACCESSORIES
Tool Bags / Cases Tool Bag (large)
Tool Bag (med.) 402094
402095 W ide opening for easy
access to contents
L arge top opening for easy Padded carrying handle
access to contents and removable shoulder
P added carrying handle strap for maximum versatility
and removable shoulder External pockets and internal separators for
strap for maximum versatility organized tool and accessory storage
External pockets and internal separators for S uits 4-6 cordless tools
organized tool and accessory storage 6 10L X 310W X 300H (mm)
Suits 3-4 cordless tools
5 50L X 260W X 270H (mm)
Worksite Trolley Bag (xlarge) 24pc 25mm Driver Bit & Socket Set
402096 797222
• R etractable handle and wheels for easy mobility 1 /4” hex adapter
• L arge top opening for 60mm magnetic bit holder
9 0mm double end ratchet
easy access to contents S ockets: 1x 6, 7, 8, 10, 11, 13mm
• External pockets and internal separators Driver bits: 1x Torx® # 10, 15, 20,
25, 30, 40, 1x Phillips 1, 2x Phillips® # 2,
for organised tool and accessory storage 1x Pozi # 1, 2x Pozi® # 2, 1x Hex # 4, 5, 6
• Padded carrying handle,
23pc Impact Wrench Bit Kit
side handle and removable
shoulder strap for maximum versatility 797223
• S uits 6-8 cordless tools
• D imensions: 660L X 410W X 300H (mm) 60mm magnetic bit holder
5 0mm impact rated bits: 1x Pozi® # 2,
Safety Glasses 1x Phillips® # 2, 1x Torx® # 20, 30
2 5mm impact rated bits:
71507 3x Phillips® # 2, 1x Phillips® # 3, 3x Pozi® # 2,
1x Pozi® # 3, 1x Hex # 4, 5, 6, 2x Torx® # 20,
Clear, duo-spherical lens with UVEX Supravision 2x Torx® # 25, 2x Torx® # 30, 1x Torx® # 40
lens coating technology
18pc 75mm Wrench Bit Kit
Rimless lenses with wide field of vision
P ermanent Anti-fog on the inside 797224
S cratch resistant on the outside
C omplies with AS/NZS 1337.1 1x Torx® # 10, 15, 20, 25, 27, 30, 40
Made in Germany 1x Slotted # 4, 6
1x Phillips® # 1, 2, 3
8m Magnetic 1x Pozi® # 1, 2, 3
Measuring Tape 1 x Hex # 3, 4, 5
797203 31pc Driver Bit Set
Suitable for everyday professional use 797225
Dual magnets assist when measuring M agnetic screwdriver handle
against metal, allowing for single person use 2 5mm driver bits: 1x Phillips® # 1, 2, 3,
L arge lock-off button to control blade when retracting 1x Square # 0, 1, 2, 1x Hex # 2, 2.5, 3, 4, 5,
and to stop at certain length for accuracy 1x Tamper Proof Torx® # 6, 7, 8, 9
Hi-Vis Kevlar Work Gloves 5 0mm driver bits: 1x Spanner # 4, 6, 8,
1x Tamper Proof Torx® # 10, 15, 20, 25, 27, 30
797208 / 797209 1x Torq # 6, 8, 10, 1x Tri-Wing # 1, 2, 3
F or power tool use, DIY, carpentry, 7pc 1/2" Impact Wrench Bit Kit
landscaping, construction and heavy duty
general purpose applications 797227
Premium Enduro Synthetic leather for outstanding durability 1/2" Drive sockets 13, 17, 19, 21, 24mm
1 /4" Hex in 1/2" in driver bit holder
S pecialised palm for maximum wear and grip
Reinforced high wear points to extend glove working life 1 /4" Hex to 1/2" square adapter
A rmoured back of hand for impact, scrapes and knocks
C omplies with AS/NZS 2161.3:2005
T wo sizes: Large (797208) and Extra Large (797209)
Unless stated accessories pictured with products are not included as standard.
79
ACCESSORIES
Stackable Case System
A new storage solution for your Hitachi gear.
F ully stackable and interlocking system.
C ases can be stacked in any order or configuration.
S uitable for a large range of corded and cordless
Hitachi Power Tools, and accessories.
O ptional wheeled trolley platform, great for a mobile
toolbox in workshops.
Optional insert boxes for System Case #1, perfect for
screws, nuts and bolts, and other small loose items.
Example pictured - all components only available separately
System Case #1
402544
External Dimensions: 295L x 395W x 101H (mm)
System Case #2
402545
External Dimensions: 295L x 395W x 158H (mm)
System Case #3
402546
External Dimensions: 295L x 395W x 210H (mm)
System Case #4
402547
External Dimensions: 295L x 395W x 315H (mm)
System Case Caster Accessory
402543
The perfect solution to make your Stackable Case System
a mobile toolbox for around the workshop.
S uits the Hitachi fully stackable and
interlocking System Case system
H eavy duty casters with brakes
E xternal Dimensions: 372L x 526W x 140H (mm)
System Case #1 Organiser
402542
Perfect addition for your System Case #1, fit up to 3 Organisers
K eep all of your screws, nails, nuts and bolts,
and other small loose items separate and tidy.
Includes 3 removable dividers.
E xternal Dimensions: 213L x 106W x 63H (mm)
Unless stated accessories pictured with products are not included as standard.
80
ACCESSORIES
ITEM CELL CAPACITY SUITABLE
NUMBER TO SUIT MODELS TYPE VOLTAGE (Ah) CHARGER
CORDLESS ACCESSORIES
REPLACEMENT BATTERIES
3.6 VOLT
EBM315 DB3DL, DB3DL2 Li-ion 3.6 1.5 UC3SFL
9.6 VOLT
EB9B All 9.6V tools NiCD 9.6 2.0 UC18YG
10.8 VOLT
BCL1015 All 10.8V tools Li-ion 10.8 1.5 UC10SFL
12.0 VOLT
BCC1215 All 12.0V tools (except WF4DY) NiCD 12.0 1.5 UC18YG
EB12B Model WF4DY NiCD 12.0 2.0 UC18YG
EB1220BL All 12.0V tools (except WF4DY) NiCD 12.0 2.0 UC18YG
14.4 VOLT
BCC1415 All 14.4V tools NiCD 14.4 1.5 UC18YG
EB14B All 14.4V tools NiCD 14.4 2.0 UC18YG
BCL1415 All 14.4V tools Li-ion 14.4 1.5 UC18YGL2
BCL1430 All 14.4V tools Li-ion 14.4 3.0 UC18YRL
18.0 VOLT
BCC1815 All 18.0V cartridge tools (except CR18DV, C6DC2) NiCD 18.0 1.5 UC18YG
EB1820 CR18DV, C6DC2 NiCD 18.0 2.0 UC18YG
EB1820L All 18.0V cartridge tools (except CR18DV, C6DC2) NiCD 18.0 2.0 UC18YG
BCL1815 All 18.0V cartridge tools (except CR18DV, C6DC2) Li-ion 18.0 1.5 UC18YGL2
EBM1830 All 18.0V cartridge tools (except CR18DV, C6DC2) Li-ion 18.0 3.0 UC18YRL
BSL1815 All 18.0V tools (slide type battery) Li-ion 18.0 1.5 UC18YKSL
BSL1825 All 18.0V tools (slide type battery) Li-ion 18.0 2.5 UC18YKSL
BSL1830C All 18.0V tools (slide type battery) Li-ion 18.0 3.0 UC18YFSL
BSL1850 All 18.0V tools (slide type battery) 1500 recharge cycles Li-ion 18.0 5.0 UC18YSL3
BSL1860 All 18.0V tools (slide type battery) 1500 recharge cycles Li-ion 18.0 6.0 UC18YSL3
24.0 VOLT
EB2420 All 24.0V tools (except DH20DV) NiCD 24.0 2.0 UC24YFB
36.0 VOLT
BSL3620 All 36.0V tools Li-ion 36.0 2.0 UC36YRSL
BSL3626 All 36.0V tools 2.6 UC36YRSL
BL36200 All 36.0V tools Li-ion 36.0 21.0 UC36YRSL
Li-ion 36.0
REPLACEMENT BATTERY CHARGERS
UC3SFL All 3.6V tools Li-ion 3.6 1.5 –
1.5 –
UC10SFL All 10.8V tools Li-ion 10.8V 1.2–2.0 –
1.2–2.0 –
UC18YG Universal NiCD battery charger NiCD 7.2–18.0 3.0–3.3 –
1.5-3.0 –
UC18YRL Universal Charger (except 3.6V, 10.8V) NiCD 7.2–18.0
- fan-cooled NiMH 14.4–18.0
- smart electronic monitoring for Lithium-ion Li-ion(c) 14.4–18.0
UC18YGL2 Universal Charger (except 3.6V, 10.8V) NiCD 7.2–18.0 1.2–2.0 –
- non fan cooled NiMH 14.4–18.0 3.0–3.3 –
Li-ion(c) 14.4–18.0 –
1.5
UC18YFSL Lithium-ion slide charger Li-ion(s) 18.0 1.5-6.0 –
- fan cooled
- smart electronic monitoring for Li-ion Li-ion(s) 18.0 1.5-3.0 –
UC18YKSL Lithium-ion slide charger Li-ion(s) 18.0 1.5–5.0 –
- non fan-cooled
UC18YML2 Mobile Lithium-ion slide smart charger
- charge from 12V DC car plug or 230V mains
- fan-cooled smart electronic monitoring
UC18YSL3 Lithium Ion Rapid Charger Li-ion (Slide) 18.0 1.5-6.0 –
- 0-6.0Ah in 38 minutes, 1500 Recharge cycles 36.0 2.0-21.0 –
- fan-cooled smart electronic monitoring
- USB output
UC36YRSL
336184 All 36.0V tools Li-ion
331987
338414 Power Adaptor for UF18DSL
Power Adaptor for UR18DSL/UR18DSL2
Power Adaptor for UR18DSAL/UR18DSDL
Unless stated accessories pictured with products are not included as standard.
81
ACCESSORIES
ITEM
NUMBER SUITS MODEL DIAMETER TEETH BORE SUITS MODEL
CIRCULAR SAW (TCT) BLADES
TS12520F Hitachi TCT Blade 125mm 18 20.0mm C18DBL
797202 Hitachi TCT Blade 125mm 24 20.0mm C18DBL
317452 Hitachi TCT Blade 165mm 40 20.0mm C18DL, C6MFA, C18DSL
324295 Hitachi TCT Blade 165mm 20 20.0mm C18DL, C18DSL, C18DBAL, C6MEY
338935 Hitachi TCT Blade 165mm 24 20.0mm C18DBAL, C18DSL, C6SS
330889 Hitachi TCT Blade 165mm 40 20.0mm C18DBAL, C18DSL, C6SS
326351 Hitachi TCT Blade for Stainless Steel 180mm 56 20.0mm CD7SA
879139 Hitachi TCT Blade 184mm 20 20.0mm C7SB2, C7D
TS18540TA Hitachi TCT Blade for Aluminium 184mm 40 20.0mm CD7SA
TS18560TA Hitachi TCT Blade for Aluminium 184mm 60 20.0mm CD7SA
330742 Hitachi TCT Blade for Mild Steel 185mm 38 20.0mm CD7SA
401932 Hitachi TCT Blade 185mm 40 20.0mm C7SB2
401934 Hitachi TCT Blade 10 Pack 185mm 24 20.0mm C7SB2
330888 Hitachi TCT Blade 190mm 20 20.0mm C7UY, C7SS, C7MFA
317928 Hitachi TCT Blade 190mm 40 20.0mm C7MFA
303359 Hitachi TCT Blade 210mm 20 25.4mm C8
996288 Hitachi TCT Blade for Aluminium 216mm 60 25.4mm C8FB2
998858 Hitachi TCT Blade 216mm 24 25.4mm C8FB2
303892 Hitachi TCT Blade 235mm 20 25.4mm C9, C9SA3
TS250100A Hitachi TCT Blade for Aluminium 250mm 100 25.4mm C10FSB, C10FSH
762466 Hitachi TCT Blade 250mm 36 16.0mm C10FR
974642 Hitachi TCT Blade 254mm 24 25.4mm C10FCH, C10FCE2
311128 Hitachi TCT Blade 254mm 24 16.0mm C10FC
TS26040 Hitachi TCT Blade 262mm 40 25.4mm C10FSB, C10FSH
TS26060 Hitachi TCT Blade 262mm 60 25.4mm C10FSB, C10FSH
TS30532 Hitachi TCT Blade 305mm 32 25.4mm C12LCH
TS305100A Hitachi TCT Blade for Aluminium 305mm 100 25.4mm C12LSH, C12RSH2
TS30560 Hitachi TCT Blade 305mm 60 25.4mm C12LSH, C12RSH2
TS31060 Hitachi TCT Blade 310mm 60 25.4mm C12FSA
TS31080 Hitachi TCT Blade 310mm 80 25.4mm C12FSA
TS380100 Hitachi TCT Blade 380mm 100 25.4mm C15FB
POLYCHRYSTALLINE DIAMOND (PCD) BLADES
797078 Hitachi PCD Blade 125mm 4 20.0mm C5YC
C7YA
797024 Hitachi PCD Blade 185mm 4 20.0mm C10FSB/H
18108 Hitachi PCD Blade 250mm 6 25.4mm
GUIDE RAIL SYSTEM FOR C7UY CIRCULAR SAW
331762 Guide Rail adaptor assembly for C7UY
744199 Guide Rail, 1400x200mm
744200 Guide Rail Clamp
744202 Guide Rail Joiner (joins two guide rails end on end)
ITEM
NUMBER TO SUIT MODELS WIDTH
PLANER BLADES
HIGH-SPEED STEEL BLADES
328935 P13F – Individual blade, 20mm wide (new type) 330mm
726341 P13F – Individual blade, 10mm wide (old type) 330mm
879417 F20SA, FFE20, FF20SA 82mm
879416 P20SB, F20A, FU20, P20SA, F20 82mm
958867 F30A 92mm
963320 P40 136mm
UNIVERSAL ADAPTOR SYSTEM TCT
IVA82 P20SB, P20SA, F20A 82mm
MINI REVERSIBLE TCT BLADES
750470 P20SA2, P20SB, P20SF, P20ST, P18DSLNN – 1 Pair 82mm
750471 P20SA2, P20SB, P20SF, P20ST, P18DSLNN – 10 Blades in plastic case 82mm
82
ACCESSORIES
ITEM PIECES FOR LENGTH
NUMBER DESCRIPTION PER PACK CUTTING MATERIAL (mm) TPI
SABRE SAW BLADES – UNIVERSAL – See page 94 for selection guide
752008 Sabre Saw Blade 5 metal BiM 150 24
752009 Sabre Saw Blade 5 metal BiM 150 14
752012 Sabre Saw Blade 5 metal BiM 150 24
752013 Sabre Saw Blade 5 metal BiM 150 18
752014 Sabre Saw Blade 5 metal BiM 225 18
752016 Sabre Saw Blade 5 metal BiM 150 14
752017 Sabre Saw Blade 5 metal BiM 225 14
752018 Sabre Saw Blade 5 metal BiM 150 progress.
752019 Sabre Saw Blade 5 metal BiM 200 8-12
752020 Sabre Saw Blade 3 metal BiM 150 8
752021 Sabre Saw Blade 3 demolition-metal BiM 225 8
752022 Sabre Saw Blade 5 wood/metal BiM 150 8-14
752023 Sabre Saw Blade 5 wood/metal BiM 305 8-14
752024 Sabre Saw Blade 5 wood/metal BiM 200 progress.
752025 Sabre Saw Blade 5 wood/metal BiM 150 6
752026 Sabre Saw Blade 5 wood/metal BiM 150 6
752027 Sabre Saw Blade 5 wood/metal BiM 305 6
752028 Sabre Saw Blade 3 wood/metal BiM 225 60
752029 Sabre Saw Blade 5 wood HCS 225 3
752030 Sabre Saw Blade 5 wood HCS 150 6
752031 Sabre Saw Blade 5 wood HCS 305 6
752032 Sabre Saw Blade 5 wood HCS 240 4-6
752033 Sabre Saw Blade 5 wood HCS 200 progress.
752034 Sabre Saw Blade 5 plaster HAS 150 6
752035 Sabre Saw Blade 2 fibreglass/st. steel CT 115 18
752036 Sabre Saw Blade 2 fibre cement CT 150 6
752037 Sabre Saw Blade 2 fibre cement CT 305 3
752038 Sabre Saw Blade 2 fibre cement CT 400 2
752039 Sabre Saw Blade 2 cast iron carbide grit 225 gritted
752043 Sabre Saw Blade 3 stainless steel BiM 150 14
752044 Sabre Saw Blade 3 stainless steel BiM 200 14
402153 Sabre Saw Blade Set 12 wood/metal various 150-225 various
JIGSAW BLADES – UNIVERSAL BAYONET TYPE – See page 92 for selection guide
321878 Jig Saw Blades 3 wood HCS 185 6
750012 Jig Saw Blades 5 aluminium/plastic HSS 100 8
750014 Jig Saw Blades 5 metal HSS 132 24
750015 Jig Saw Blades 5 metal HSS 132 14
750019 Jig Saw Blades 5 wood HCS 100 10
750021 Jig Saw Blades 5 wood HCS 100 8
750025 Jig Saw Blades 5 sheetmetal HCS 70 14
750027 Jig Saw Blades 5 wood HCS 116 8
750028 Jig Saw Blades 5 thick wood HCS 132 6
750029 Jig Saw Blades 5 wood HCS 116 12.7-8.5
750030 Jig Saw Blades 2 fibre cement Carbide 100 6
750031 Jig Saw Blades 5 wood with nails BiM 132 10.6-5.1
750032 Jig Saw Blades 5 sheetmetal BiM 132 14
750033 Jig Saw Blades 5 metal HSS 100 21.2-9.8
750035 Jig Saw Blades 2 fibre cement Carbide 76 grit (med)
750036 Jig Saw Blades 5 plywood HCS 76 18
750037 Jig Saw Blades 5 laminates/plastic BiM 100 15
750038 Jig Saw Blades 5 metal HSS 91 24
750039 Jig Saw Blades 5 stainless steel BiM 91 24
750040 Jig Saw Blades 5 sheetmetal HSS 76 14
750041 Jig Saw Blades 5 sheetmetal BiM 76 14
750042 Jig Saw Blades 5 wood HCS 91 11-14
750043 Jig Saw Blades 5 wood HCS 100 6
750045 Jig Saw Blades 5 plywood HCS 100 6
750046 Jig Saw Blades 5 wood HCS 100 6
750047 Jig Saw Blades 2 fibre cement Carbide 76 grit (coarse)
750049 Jig Saw Blades 10 various HSS/HCS various various*
*Mixed 10 piece starter pack
83
ACCESSORIES
WIDTH/
ITEM FOR LENGTH BLADE
NUMBER DESCRIPTION CUTTING MATERIAL (MM) STYLE
MULTI TOOL ACCESSORIES – See page 90 for selection guide
335887 Plunge Cutting Stainless Steel HM/TC 20/30 AIZ 20 AT
335886 Plunge Cutting 32/40 AIZ 32 AT
335885 Plunge Cutting Stainless Steel HM/TC 10/20 AIZ 10 AB
335884 Plunge Cutting 20/20 AIZ 20 AB
335883 Plunge Cutting Metal Bi-M 32/30 AIZ 32 AB
335881 Plunge Cutting 28/50 AIZ 28 EB
335882 Plunge Cutting Metal Bi-M 32/50 AIZ 32 EPB
335869 Plunge Cutting 65/40 AIZ 65 BB
335880 Segment Saw Metal Bi-M Ø85 ACZ 85 EB
335873 Plunge Cutting 10/30 AIZ 10 EC
335872 Plunge Cutting Wood & Metal Bi-M 20/30 AIZ 20 EC
335871 Plunge Cutting 32/40 AIZ 32 EC
335875 Plunge Cutting Wood & Metal Bi-M 32/40 AIZ 32 EPC
335870 Plunge Cutting 32/40 AIZ 32 BB
335876 Plunge Cutting Wood & Nails Bi-M 32/40 AIZ 32 BPB
335878 Plunge Cutting 65/40 AIZ 65 BSB
335895 T/Carbide Grit Plunge Wood & Metal Bi-M 20/20 AIZ 20 RT
335894 T/Carbide Grit Plunge 32/30 AIZ 32 RT
335890 Thin Kerf T/Carbide Grit Segment Wood HCS Ø65 ACZ 65 RT
335897 T/Carbide Grit Segment Saw Ø85 ACZ 85 RT
335891 Diamond Grit Segment Wood HCS Ø85 ACZ 85 RD
335904 T/Carbide Grit Cutting & Sanding Ø70 AVZ 70 RT
335905 T/Carbide Grit Delta Blade Wood HCS Ø78 AVZ 78 RT
335900 Universal Groove Cutter/Silicone Remover 28/50 AIZ 28 SC
335877 Serrated Groove Cutter/Silicone Remover Wood HCS 28/50 AIZ 28 SWC
335901 Rigid Scraper 52/26 ATZ 52 SC
335902 Flexible Scraper Hardwood Bi-M 52/45 ATZ 52 SFC
335896 Serrated Knife Ø100 ACZ 100 SWB
335889 Segment Saw Hardwood Bi-M Ø65 ACI 65 AB
335888 Segment Saw Ø85 ACI 85 EB
335892 Round Sawblade Hardwood Bi-M Ø85 AOI 85 EB
335903 Sanding Pad 93/93 AVI 93 G
Ceramics & Grout HM/TC
Ceramics & Grout HM/TC
Ceramics & Grout HM/TC
Ceramics & Grout HM/TC
Ceramics & Grout HM/TC
Ceramics & Grout HM/TC
Abrasive HM/TC
Multi-Material HCS
Multi-Material HSS
Multi-Material HCS
Multi-Material HCS
Soft Materials Bi-M
Multi-Material BiM-TiN
Multi-Material BiM-Tin
Multi-Material BiM-TiN
Abrasive
ITEM
NUMBER TO SUIT MODELS
DUST EXTRACTION ADAPTORS
323918 All 100mm Grinders
300082 SV12SD, FSV13Y
321591 CJ110MV, CJ110MVA, CJ90VST, CJ18DSLNN
313928 P20SB
329063 C18DBL
997466 M8SA2, M12SE, M12VE, TR12
308506 C10FCE2, C10FSB, C10FSH, C12RSH, C12LSH
980802Z SAY150A
306022 P13F
302981 C7MFA, C6MFA, C7SS
997247 C7UY
303377 C7SB2, C8
303930 C9
324669 C9SA2
963558 Rubber Adapter to connect above adapters to extractor hoses (32mm ID)
334502 P18DSL, P20SF
334503 Elbow to suit 334502 adaptor (P18DSL, P20SF)
84
ACCESSORIES
ITEM
NUMBER TO SUIT MODELS
GRINDER ACCESSORIES
WHEEL NUTS (threaded, with pin spanner holes)
339578 All current 100mm Grinders
339579 All current 115mm and 125mm Grinders
937909Z For DC wheel and Diamond Blade use, current 180mm and 230mm Grinders (45mm dia.)
937917Z For cut-off wheel use, current 180mm and 230mm Grinders (90mm dia.)
WHEEL WASHERS (unthreaded)
320497 All current 100mm Grinders
937817Z All current 115mm and 125mm Grinders
937908Z All current 180mm and 230mm Grinders (90mm dia.)
937907Z All current 180mm and 230mm Grinders – for use with Diamond Blades (45mm dia.)
PIN SPANNERS
313933 All current 100mm Grinders
938332Z All current 115mm and 125mm Grinders
325491 All current 180mm and 230mm Grinders
ITEM
NUMBER TO SUIT MODELS DIAMETER BORE SIZE
DIAMOND BLADES AND ACCESSORIES 20mm/16mm
20mm/16mm
313527 wet/dry segmented 106mm 20mm/16mm
797116 dry continuous rim 105mm 20mm/16mm
797111 dry segmented 105mm
700004 dry segmented 114mm 22mm
797112 dry segmented 115mm 22mm
797123 dry continuous rim 125mm 22mm
797113 dry segmented 125mm 22mm
797114 dry segmented 180mm 22mm
797115 dry segmented 230mm 25.4mm
DC300SC dry segmented 300mm 25.4mm
773007 dry segmented 350mm
WETKIT Hose & Tap Kit (for CM4SB2)
ITEM THREAD MOUNTING CAPACITY
NUMBER TO SUIT MODELS
M10x1.5
SANDING ACCESSORIES (FOR ANGLE GRINDERS / SANDERS) M14x2
M14x2
936558Z Rubber Sanding Pad 100mm
937825Z
935652 Rubber Sanding Pad 115mm
953247Z
935513 Rubber Sanding Pad 125mm
937826Z
953246Z Rubber Sanding Pad 180mm
309419
324209 Pad Lock Nut - for 100mm Grinders
980780
980803Z Pad Lock Nut - for 115mm Grinders
753817
Pad Lock Nut - for 125/180mm Grinders
FSV13Y Sanding Pad (hook and loop) 125mm
SV13YB Sanding Pad (hook and loop) 125mm
SAY150A Sanding Pad 150mm
SAY150A Perforator
SAY150A Sanding pad (hook and loop) 150mm
ITEM DIAMETER
NUMBER TO SUIT MODELS
POLISHING ACCESSORIES
312518 Polishing Sponge for models SV13YB & FSV13Y 150mm
949103 Woollen Bonnet for models SAT180 & SP18VA 180mm
85
ACCESSORIES
ITEM
NUMBER TO SUIT MODELS THREAD MOUNTING CAPACITY
CHUCKS AND KEYS
318835 D10YB 3/8” x 24 10mm
3/8” x 24 10mm
950292 D10VC2 1/2” x 20 10mm
1/2” x 20 10mm
321811 DUT10 1/2” x 20 13mm
1/2” x 20 13mm
321812 DW15Y No.3 Jacobs Taper 16mm
5/8” x 16 16mm
319303 D13VG
321818 All 13mm Drills (Roehm type)
950265 PUPM3
950284 VTV16, VTP16A
KEYLESS CHUCKS
331602 DS10DFL, DS12DVC 3/8” x 24 10mm
1/2” x 20 10mm
322167 DS14DVF3, DS14DFL 1/2” x 20 13mm
1/2” x 20 13mm
320684 DS18DSL, DV18DSL 1/2” x 20 13mm
1/2” x 20 13mm
332049 DS18DVC 1/2” x 20 13mm
1/2” x 20 13mm
323898 DS18DL, DV18DL, DS18DSDL, DS18DBL2 1/2” x 20 13mm
1/2” x 20 13mm
322357 DV16V 1/2” x 20 13mm
1/2” x 20 13mm
319546 DV20VB2, D13VB3, DV20VD, DV22V
331914 DS18DBL, DV18DBL, DV18DSDL, DV18DBL2
330586 DS18DSFL, DV18DSFL
335961 DV18DBEL, DS18DBEL
336852 DS18DJL
336885 DV18DJL
CHUCK KEYS
930119 All 10mm Drills (except D10YB) 10mm
980057 D10VC2 10mm
319070 D10YB 10mm
319527 D13VG 13mm
987575 Suits 13mm Roehm chuck 321818 13mm
930733 VTV16, VTP16A 16mm
CHUCK ADAPTORS (FOR SCREWDRIVERS, WRENCHES AND ROTARY HAMMERS)
307543 W4YD, WF4DY, all Cordless Impact Drivers 1/2” x 20
compatible with 321811 (keyed) or 332049 (keyless) chucks 1/2” x 20
1/4” hex
303624 DH22PG, DH24PC3, DH30PC2 (and all other SDS+ drills)
1/2” x 20
751875 Cordless Impact Wrench Adaptor 1/2” SQ. – 1/4” HEX.
752500A Cordless Impact Driver Adaptor 1/4” HEX. – 1/2” SQ.
751970 Hitachi Impact Driver Adaptor Set (1/4” hex to 1/4”, 3/8” and 1/2” square drive)
752097 Chuck adaptor SDS+ with 13mm keyed chuck
ANGLE DRILL ATTACHMENT
319528 2-speed attachment fits D13VG and DV24DV
DRIVER BITS – FOR COLLATED SCREWDRIVERS
324134 Driver Bit for W4YD, WF18DSL (#2 Phillips)
307011 Driver Bit for W4YF (#2 Phillips)
313880 Driver Bit for WF4DY, WF4V (#2 Phillips)
752376 2pack Driver bits for W4YD, WF18DSL (#2 Phillips)
TORCH / WORKLAMPS – SPARE BULBS
330267 Spare bulbs for UB10DL Torch (2 bulbs in pack) 10.8V
314424 Spare bulbs for UB12D Torch (2 bulbs in pack) 9.6V/12.0V
318767 Spare bulbs for UB18D/UB18DAL Torch (2 bulbs in pack) 14.4V/18.0V
320546 Spare bulbs for UB24D Torch (2 bulbs in pack) 24.0V
323339 Spare bulb for UB18DL/UB18DSL Worklamp (1 bulb in pack) 14.4V/18.0V
86
ACCESSORIES
ITEM TOTAL LENGTH
NUMBER DESCRIPTION (mm)
ROTARY HAMMER DRILL / BREAKER ACCESSORIES
BULL POINTS
751590 DH24PC3, DH26PC, DH28PCY, DH30PC, DH30PC2 – SDS+ 250
313471 DH38MS, H60MR, DH40MEY, DH52MEY, H60MC, H41MB, H45MEY, H60MEY – SDS MAX 280
313472 DH38MS, H60MR, DH40MEY, DH52MEY, H60MC, H41MB, H45MEY, H60MEY – SDS MAX 400
751543 H65SB, H65SA, PH65A, H65SB2, H65SB3 410
955623 H50SA 450
981922 H41SA, DH40YB 280
981923 PH40F, H41SA, DH40YB 450
955613 H50SA 320
986947 H55SA, DH50SA1 300
985230 H90SB, H90SG(G1) 520
COLD CHISELS
751591 DH24PC3, DH26PC, DH28PCY, DH30PC, DH30PC2 – SDS+ 250
313473 DH38MS, H60MR, DH40MEY, DH52MEY, H60MC, H41MB, H45MEY, H60MEY – SDS MAX 280
313474 DH38MS, H60MR, DH40MEY, DH52MEY, H60MC, H41MB, H45MEY, H60MEY – SDS MAX 400
981925 PH40F, H41SA, DH40YB 280
981926 PH40F, H41SA, DH40YB 450
955614 H50SA 320
986953 H55SA, DH50SA1 320
401990 H65SB, H65SA, PH65A, H65SB2, H65SB3 410
985231 H90SB, H90SG(G1) 520
GROOVING CHISEL
316659 DH24PC3, DH26PC, DH28PCY, DH30PC, DH30PC2 – SDS+ 250
CUTTERS
797054 DH24PC3, DH26PC, DH28PCY, DH30PC, DH30PC2 – SDS+ 250x40
313475 DH38MS, H60MR, DH40MEY, DH52MEY, H60MC, H41MB, H45MEY, H60MEY – SDS MAX 400x50
751545 H65SB, H65SA, PH65A, H65SB2, H65SB3 410x75
981924 DH2BY, DH38YB1, PH40F, H41SA, DH40YB 280x50
955629 H50SA 320x50
986951 H55SA, DH50SA1 320x50
985232 H90SB, H90SG(G1) 520x75
SCOOPS AND SPADES
956126 DH28Y, DH38YB1, PH40F, H41SA, DH40YB 405
313476 DH38MS, DH40MEY, DH52MEY, H60MR, H60MC, H41MB, H45MEY, H60MEY – SDS MAX 390
980034 H50SA 455
319298 H65SB, H65SA, PH65A, H65SB2, H65SB3 380
985233 H90SB, H90SG(G1) 546
SHANKS FOR RAMMING AND BUSHING TOOLS
955625 H50SA 260
944966 H65SB, H65SA, PH65A, H65SB2, H65SB3 250
313479 DH38MS, DH40MEY, DH52MEY, H60MC, H41MB, H45MEY, H60MEY – SDS MAX 220
RAMMERS (Rammers require the correct shank – see above)
313478 Square Plate 150x150sq
955181 Round Plate 140 (dia)
944965 Round Plate 200 (dia)
BUSHING TOOLS (Bushing tool require the correct shank – see above)
955183 All models
313477 DH38MS, DH40MEY, DH52MEY, H41MB, H60MR, H60MC, H45MEY, H60MEY – SDS MAX (no shank required)
CHUCK ADAPTORS
303624 DH26PC, DH24PG, DH28PCY, DH24PC3, DH30PC2, DH22PG – SDS+ – 1/2 x 20 thread
313465 SDS MAX – SDS+ Adaptor
313468 DH38MS, DH40MEY, DH52MEY – SDS MAX – 1/2 x 20 thread
752097 Chuck adaptor SDS+ with 13mm keyed chuck
750246 V2 Hex Shank to SDS+ Adaptor (for older models, DH40YB, etc)
CHUCK – requires 303624 adaptor above
321818 13mm Keyed Chuck
DRIVING ADAPTORS – suitable for Warratah stakes, Marquee pegs and Earthing rods
797012 H65SB, H65SA, H65SB2, H65SB3 – Warratah/Marquee peg driver (51mm ID diameter)
797013 H65SB, H65SA, H65SB2, H65SB3 – 13mm Earthing rod driver
87
ACCESSORIES
ITEM
NUMBER INCLUDES
SDS+ ROTARY HAMMER DRILL BIT SET
751024 5pce SDS+ drill bit set
Contains: 2 x 6mm, 2 x 8mm, 1 x 10mm,
Supplied in reusable hard plastic case
Genuine SDS+, Made in Germany
ITEM DIA. TOTAL WORKING ITEM DIA. TOTAL WORKING ITEM DIA. TOTAL WORKING
NO.
LENGTH LENGTH NO. LENGTH LENGTH N0. LENGTH LENGTH
SDS+ ROTARY HAMMER DRILL BITS
750100 4.0 110 50 751701 4.0 160 100 782404 5.0 110 50
751702 5.0 140 800 750102 5.0 160 1000 750103 5.5 110 500
782411 5.5 160 1000 782413 5.5 260 200 782415 6.0 110 50
150 782418 6.0 260 200
782416 6.0 160 100 782417 6.0 210 100 750109 7.0 110 50
750107 6.5 110 50 782423 6.5 160 782433 8.0 160 100
750110 7.0 160 100 750111 8.0 110 50 750115 8.0 310 250
200 750118 10.0 110 50
750113 8.0 210 1500 750114 8.0 260 150 782447 10.0 260 200
150 750123 10.0 450 400
750160 9.0 160 100 750117 9.0 210 300 782458 12.0 160 100
782445 10.0 160 100 782446 10.0 210 200 782461 12.0 310 250
782448 10.0 310 250 751719 10.0 350 200 750131 13.0 160 100
400 750134 14.0 210 150
750124 11.0 160 100 750125 11.0 260 100 750137 15.0 160 100
400 782484 16.0 210 150
750127 12.0 210 150 750128 12.0 260 100 751730 17.0 210 150
751723 12.0 360 300 750130 12.0 450 400 782495 18.0 450 400
250 750148 19.0 450 400
782469 13.0 260 200 782471 14.0 160 250 782503 20.0 450 400
250 782508 22.0 450 400
782474 14.0 310 250 750136 14.0 450 200 782516 25.0 250 200
750138 15.0 260 200 750139 16.0 160 400
782486 16.0 310 260 782487 16.0 450 752229 28.0 450 400
400
782491 18.0 200 150 782494 18.0 300
400
750146 19.0 200 150 750147 19.0 300
782500 20.0 210 150 782502 20.0 300
750152 20.0 600 550 750153 22.0 250
750155 24.0 250 200 750156 24.0 450
751736 26.0 250 200 751737 26.0 450
752230 30.0 250 200 752231 30.0 450
SDS MAX ROTARY HAMMER DRILL BITS
750910 12 340 200 750911 12 540 400
750912 12 690 550 750914 14 340 200 750915 14 540 400
750917 15 340 200 750918 15 540 400 54301 16 340 200
754302 16 540 400 54305 18 340 200 750923 18 540 400
313449 19 340 200 313457 19 540 400 54309 20 320 200
754310 20 520 400 754313 22 320 200 754314 22 520 400
754317 24 320 200 754318 24 520 400 754319 25 320 200
754320 25 520 400 754323 26 520 400 750936 28 370 250
754325 28 570 450 750939 30 370 250 750940 30 570 450
750941 32 370 250 750942 32 570 450 750944 35 370 250
750945 35 570 450 750947 38 370 250 750948 38 570 450
750949 40 370 250 750950 40 570 450 754351 50 570 450
ITEM TOTAL LENGTH
NUMBER DESCRIPTION (mm)
SDS+ ROTARY HAMMER DRILL / BREAKER ACCESSORIES
751590 Bull point 250
751591 Cold chisel 250
316659 Grooving Chisel 250
797054 Cutter (offset for tile removal) 250
303624 Chuck adaptor SDS+ to 1/2 x 20 thread mount
752097 Chuck adaptor SDS+ with 13mm keyed chuck
88
ACCESSORIES
ITEM TOTAL LENGTH
(mm)
NUMBER DESCRIPTION
220
SDS MAX ROTARY HAMMER / BREAKER ACCESSORIES
280
313465 SDS MAX – SDS+ Adaptor 400
313468 Chuck Adaptor SDS MAX to 1/2 x 20 thread mount 280
313471 Bull Point 500
313472 Bull Point 500
313473 Cold Chisel 390
313474 Cold Chisel
313475 Cutter 150x150
313476 Scoop 220
313477 Bushing Tool (requires shank, see below)
313478 Rammer (requires shank, see below)
313479 Shank (required for rammer and bushing tool)
CODE STD AUTOSTOP CODE STD AUTOSTOP CODE STD AUTOSTOP
REPLACEMENT CARBON BRUSHES
C10FCE2 999065 DH28PCY 999041 999072 GP2S2 999088 999076
C10FSB 999043 999073 DH30PC2 999073 GP3V 999088 999076
C10FSH 999043 999073 DH38MS 999043 999073 GP5V 999088 999076
C12LCH 999065 DH40MRY 999073 H41MB 999043 999073
C12LSH 999065 DH50MRY 999074 H60MC 999074
C12RSH 999065 DN18DSL 999054 H60MR 999074
C6SS 999043 DS18DSDL 999054 H65SB2 999086
C7MFA 999043 999073 DS18DSL 999054 H90SG 999086
C7SB2 999038 999071 DV13VSSG1 999041 999072 M12SE 999038 999071
C7SS 999043 999073 DV16V 999041 999072 M12VE 999038 999071
C7UY 999043 999073 DV16VSSG1 999041 999072 M8SA2 999043 999073
C7YA 999038 999071 DV16VSSGA 999041 999072 P13F 999044 999074
C8 999038 999071 DV18DL2 999054 P18DSL 999017
C9SA2 999038 999071 DV18DSDL 999054 P20SA2 999041 999072
CC14SF 999044 999074 DV18V 999041 999072 P20SF 999021 999070
CD7SA 999043 999073 DV20VD 999088 999076 P20ST 999021 999070
CE16SA 999021 999070 DV22V 999088 999076 RB40VA 999021 999070
CJ110MV 999041 999072 FSV10SA 999041 999072 SAT180 999043 999073
CJ110MVA 999041 999072 G10SN 999005 SAY150A 999021 999070
CJ65V3 999041 999072 G10SR3 999005 SB10S2 999043 999073
CJ90VST 999041 999072 G10SS2 999067 SB8V2 999043 999073
CM12Y 999044 999074 G12SA3 999088 999076 SP18VA 999043 999073
CM4SB2 999043 999073 G12SE2 999088 999076 SS10A 999041 999072
CM5SB 999088 999076 G12SN 999005 SS10B 999041 999072
CM9SR 999044 999074 G12SR3 999005 SV12SD 999041 999072
CN16SA 999021 999070 G12SS2 999067 SV12SG 999041 999072
CR13V 999043 999073 G13SB3 999088 999076 SV13YB 999041 999072
CR13VB 999043 999073 G13SC2 999043 999073 VTV16 999043 999073
CR13VBY 999043 999073 G13SE2 999088 999076 W4YD 999021 999070
CR18DSL 999068 G13SN 999005 W6VA4 999091
CS36DL 999068 G13SR3 999005 W6VB3 999091
D10VC2 999041 999072 G13SW 999088 WF18DSL 999054
D10YB 999021 999070 G13VA 999088 999076 WH18DL2 999054
D13 999073 G13YC2 999088 999076 WH18DSL 999054
D13VB3 999041 999072 G18DL 999054 WH18DSDL 999054
D13VG 999041 999072 G18DSL 999101 WR18DL 999054
D6SH 999041 999072 G18MR 999061 999089 WR18DL2 999054
DH18DSL 999100 G18SEY 999061 999089 WR18DSDL 999054
DH22PG 999041 999072 G23MR 999061 999089 WR18DSHL 999100
DH24PC3 999041 999072 G23SEY 999061 999089 WR22SA 999043 999073
DH24PG 999041 999072 G23SR 999044 999074
DH26PC 999041 999072 G23SS 999038 999071
89
ACCESSORIES
MULTI TOOL ACCESSORIES
Width Material Stanless Steel Hardened Steel Metal Non ferrous metals Metal stud Wood with nails
Cutting depth
Thickness
Tooth pitch
Part No. mm mm mm mm TPI HSS
HCS
40 - 50 HRC
SAPLNADITNEG MULTI M ATERI AL ABRASIVE S WOO D +WMOEOTADL METAL INOX 335887 20 30 1,0 1,1 24 HM/TC • • • • o
335886 32 40 1,0 1,1 24 HM/TC • • • • o
335885 10 20 0,7 1,3 20 BiM •••
335884 20 20 0,7 1,3 20 BiM •••
335883 32 30 0,7 1,3 20 BiM •••
335881 28 50 0,6 1,4 18 BiM oo •
335882 32 50 0,6 1,M4 ulti To18ol BiM oo •
Blade Chart1,8 14 BiM •
335869 65 40 0,6
1,4 18 BiM oo •
335880 Ø 85 21 0,9
335873 10 30 0,6 1,4 18 HCS
335872 20 30 0,6 1,4 18 HCS
335871 32 40 0,6 1,4 18 HCS
335875 32 40 0,6 1,4 18 HCS
335870 32 40 0,6 1,8 14 BiM
335876 32 40 0,6 1,8 14 BiM
335878 65 40 0,6 1,8 14 BiM
335895 20 20 2,0 Hm riff 50 HM/TC
335894 32 30 2,0 Hm riff 50 HM/TC
335890 Ø 65 11 1,6 Hm riff 50 HM/TC
335897 Ø 85 21 2,0 Hm riff 30 HM/TC
335891 Ø 85 21 2,0 Diamond riff 40 Diamond
335905 78 x 78 - - Hm riff 30 HM/TC
335904 Ø 70 13 2,0 Hm riff 40 HM/TC
335900 28 50 1,0 Ground knife HCS
335877 28 50 1,0 Serrated knife HSS
335901 52 26 0,8 Ground knife, rigid HCS
335902 52 38 0,4 Ground knife, flexible HCS
335896 Ø 100 27 0,7 Serrated knife BiM
335889 Ø 65 13 0,9 1,2 22 BiM TIN ••
335888 Ø 85 20 0,9 1,5 17 BiM TIN ••
335892 Ø 85 20 0,9 1,5 17 BiM TIN ••
335903 93 x 93 - 10,0 Hook and loop
sanding pad
90
ACCESSORIES
MULTI TOOL ACCESSORIES
Wood
Soft wood boards
Sandwich materials
Laminate
Hard wood
Tile cutting
Grinding
Joint cutting
Filing
Epoxy
Fibreglass
Carpets
Isolation material
Leather
Rubber
Seals/putty
Soft residues
Hard Residues
silicon
o•
o•
oo
oo
oo
• o • oo •
• o • oo •
• o • oo •
oo• •o •
••
••
••
•••
••••
••••
•• ••
>2.2 • •
>2.2 • •
• >1.6 •
• >2.5 •
• >2.0 •
•
o • >2.2 o
••
••
oo •
• •o
•o• •
oo• •
••
••
• primarily suitable for o also suitable for
91
ACCESSORIES
JIGSAW BLADE SELECTION GUIDE
Pack Quantity Material
Total Length
Toothed Length
Height
Thickness
Pitch
Part No. mm mm mm TPI HSS
HCS
82.6 56.0 9.3 1.0
S/STEELMETAL 750011 2 91.5 65.0 7.5 1.0 1.4 18 HM/TC
WOOD 750038 5 91.5 65.0 7.5 1.0 Progress. 17-24 HSS
+ METAL 750039 5 132.0 105.0 9.5 1.0 Progress. 17-24 BiM
750014 5 100.4 75.0 8.6 1.0 HSS
750033 5 91.5 65.0 7.5 1.0 1.0 24 HSS
750040 5 91.5 65.0 7.5 1.0 Progress. 10-20 HSS
750041 5 132.0 105.0 7.5 1.3 Progress. 11-14 BiM
750015 5 132.0 105.0 7.5 1.0 Progress. 11-13 HSS
750032 5 100.4 75.0 7.5 1.0 BiM
750012 5 70.0 50.0 7.5 1.0 1.8 14 HSS
750025 5 1.8 14 HSS
132.0 105.0 10.0 1.3 3.0 8
750031 5 1.8 14 BiM
76.6 54.0 4.7 1.3
WOOD 750036 5 91.5 65.0 7.5 1.0 Progress. 5-10 HCS
750042 5 116.5 90.0 9.2 1.5 HCS
750029 5 100.4 75.0 7.2 1.5 1.4 18 HCS
750019 5 100.4 75.0 9.5 1.3 HCS
750021 5 100.4 75.0 7.2 1.3 Progress. 11-14 HCS
750043 5 100.4 75.0 6.0 1.3 HCS
750046 5 132.0 107.0 7.2 1.7 Preogress. 8-12 HCS
750028 5 100.4 75.0 7.2 1.5 HCS
750045 5 116.5 90.0 7.2 1.5 2.5 10 HCS
750027 5 100.4 74.0 7.5 1.3 HCS
750037 5 82.6 56.0 8.0 0.8 3.0 8 BiM
750047 2 100.4 75.0 8.2 1.3 HM/TC
750030 2 132.0 107.0 8.2 1.25 Progress. 5-8 HM/TC
750035 2 HM/TC
Progress. 5-8
4.0 6
Progress. 5-8
3.0 8
1.7 15
SPECIAL Gritted Grain 30
4.0 6
4.0 6
92
ACCESSORIES
JIGSAW BLADE SELECTION GUIDE
Stainless Steel
Construction timber with nails
Metal Profile / Plates / Pipe
Sheet Metal
Aluminium
Profile Pipe – SHS
(Square Hollow Section)
Plastic
Softwood Boards
Plywood
Coarse Wood
Laminate Boards
Plaster Board
Fibre Cement
Ceramic Wall Tiles
Sandwich Material
•
1-3mm
1-3mm
1-3mm <65mm •
1.5-10mm <30mm •
2.5-6mm
2.5-6mm
2.5-6mm <65mm •
2.5-6mm <65mm • <65mm •
3-15mm <30mm 3-100mm
1-3mm
•• < 30mm 3-100mm <65mm
2-15mm • •
2-15mm •
2-65mm
3-30mm •
4-50mm
5-50mm
5-50mm
5-100mm <100mm
10-45mm
10-65mm
<65mm •
<65mm 5-15mm
<80mm
•••
•••
• primarily suitable for o also suitable for
93
ACCESSORIES
SABRE SAW BLADE SELECTION GUIDE
Pack Quantity Material Stainless Steel
Total Length Metals
Toothed Length Sjeet Metals
Height Metal Pipes
Thickness
Pitch
Part No. mm mm mm TPI HSS
HCS
S/STEEL 752043 3 150.0 128.5 19.0 0.90 1.8 14 BiM ••
752044 3 200.0 178.5 19.0 0.90 1.8 14 BiM ••
752035 2 115.0 93.5 19.0 1.25 1.4 18 HM/TC • o
752008 5 150.0 128.5 16.0 0.90 1.0 24 BiM • oo
752009 5 150.0 128.5 16.0 0.90 1.8 14 BiM • oo
752012 5 150.0 128.5 19.0 0.90 1.0 24 BiM • •o
752014 5 225.0 203.5 19.0 0.90 1.4 18 BiM • •o
METAL 752016 5 150.0 128.5 19.0 0.90 1.8 14 BiM • •o
752018 5 150.0 128.5 19.0 0.90 Progress. 8-14 BiM • oo
752017 5 225.0 203.5 19.0 0.90 1.8 14 BiM •o•
752013 5 150.0 128.5 19.0 0.90 1.4 18 BiM •o•
752021 3 225.0 203.5 22.0 1.60 2.5-3.0 8-10 BiM ••
752019 5 200.0 178.5 19.0 1.25 1.8-2.6 10-14 BiM •o•
752020 3 150.0 128.5 22.0 1.60 2.5-3.0 8-10 BiM o•
752022 5 150.0 128.5 19.0 0.90 1.8-2.6 10-14 BiM •o•
WOOD + METAL 752023 5 305.0 283.5 19.0 0.90 1.8-2.6 10-14 BiM ••
752024 5 200.0 178.5 19.0 1.25 Progress. 6-12 BiM •
752028 3 225.0 203.5 22.0 1.60 4.3 6 BiM o
752026 5 150.0 128.5 19.0 1.26 4.3 6 BiM
752027 5 305.0 283.5 19.0 1.25 4.3 6 BiM
752025 5 150.0 128.5 19.0 1.25 4.3 6 BiM
752030 5 150.0 128.5 19.0 1.25 4.3 6 HCS
WOOD 752031 5 305.0 283.5 19.0 1.25 4.3 6 HCS
752033 5 200.0 178.5 19.0 1.25 Progress. 6-10 HCS
752029 5 225.0 203.5 19.0 1.25 8.5 3 HCS
752032 5 240.0 218.5 19.0 1.50 5.0 5 HCS
752034 5 150.0 128.5 19.0 1.00 4.3 6 HAS
SPECIAL 752039 2 225.0 203.5 19.0 1.25 Gritted Grain 30 HM/TC
752036 2 150.0 128.5 19.0 1.25 4.3 6 HM/TC
752037 2 305.0 283.5 22.0 1.50 8.5 3 HM/TC
752038 2 400.0 378.5 22.0 1.50 12.7 2 HM/TC
94
• primarily suitable for ooooo oo • ooo •• • ooo o o oo Non-Ferrous Metals
Aluminium
•o o oo o •o o Steel pipe / Cast pipes
•o Fibre Materials
•• o •• • •oo • •o o• • • • • • ••• o• oo oo o PVC / Plastic Materials ACCESSORIES
•• o Plastic Profiles
• Wood with nails SABRE SAW BLADE SELECTION GUIDE
Solid Wood
o also suitable for • oo ••• • oo o o o Chipboard
Plywood /
• o• Wood Combinations
Green Wood
o Limestone
• Sandwich materials -
• Cement Bonded Chipboard
o Plaster Board
ooo Aerated
o Bricks
Tiles
•• Drywall
oooo Ceramic Wall Tiles
o• • •oo
oo • ooo
oo • ooo
95
Dust Extraction Connection System Chart
CUTTING Dust Extractor Fitting Coupling Hose Connection Tool Dust Extractor Fitting Coupling Hose Connection
Tool
Any Nilfisk hose with NOT Any Nilfisk hose with
963558 tool adaptor fitted REQUIRED 963558 tool adaptor fitted
G10SR4 323918 C7YA
C18DBL 329063 Any Nilfisk hose with C7UY 997247 Any Nilfisk hose with
963558 tool adaptor fitted 963558 tool adaptor fitted
C18DBAL 339383 Any Nilfisk hose with C9SA3 324669 Any Nilfisk hose with
963558 tool adaptor fitted NOT 963558 tool adaptor fitted
C18DSL 324580 Any Nilfisk hose with C10FCE2 REQUIRED Any Nilfisk hose with
963558 tool adaptor fitted 308506 tool adaptor fitted
NOT
CJ18DSL 321591 Any Nilfisk hose with C10FSB REQUIRED Any Nilfisk hose with
963558 tool adaptor fitted 308506 tool adaptor fitted
NOT
CV18DBL 337936 Any Nilfisk hose with C10FSH REQUIRED Any Nilfisk hose with
963558 tool adaptor fitted 308506 tool adaptor fitted
NOT
CJ110MVA 321591 Any Nilfisk hose with C12LCH REQUIRED Any Nilfisk hose with
963558 tool adaptor fitted 308506 tool adaptor fitted
NOT
CJ90VST 321591 Any Nilfisk hose with C12RSH2 REQUIRED Any Nilfisk hose with
963558 tool adaptor fitted 308506 tool adaptor fitted
NOT
CV350V 337922 Any Nilfisk hose with CM12Y REQUIRED Any Nilfisk hose with
963558 tool adaptor fitted 963558 tool adaptor fitted
NOT
C6SS 302981 Any Nilfisk hose with CM5SB REQUIRED Any Nilfisk hose with
963558 tool adaptor fitted 963558 tool adaptor fitted
NOT
Any Nilfisk hose with REQUIRED Any Nilfisk hose with
963558 tool adaptor fitted 963558 tool adaptor fitted
C7MFA 302981 CM9SR
SANDING
NOT Any Nilfisk hose with SV13YB NOT Any Nilfisk hose with
FSV10SA REQUIRED 963558 tool adaptor fitted SAY150A REQUIRED 963558 tool adaptor fitted
SV12SG NOT Any Nilfisk hose with NOT Any Nilfisk hose with
REQUIRED 963558 tool adaptor fitted REQUIRED 963558 tool adaptor fitted
Any Nilfisk hose with NOT Any Nilfisk hose with
963558 tool adaptor fitted REQUIRED 963558 tool adaptor fitted
SV12SD 300082 SB8V2
96
Dust Extraction Connection System Chart
PLANERS Dust Extractor Fitting Coupling Hose Connection ROUTERS Dust Extractor Fitting Coupling Hose Connection
Tool Tool
P18DSL 334502 Any Nilfisk hose with M8SA2 339380 Any Nilfisk hose with
P20SF 308506 tool adaptor fitted 963558 tool adaptor fitted
P20ST
P13F 334502 Any Nilfisk hose with M12SE 339380 Any Nilfisk hose with
308506 tool adaptor fitted 963558 tool adaptor fitted
334502 Any Nilfisk hose with M12VE 339380 Any Nilfisk hose with
306022 308506 tool adaptor fitted 963558 tool adaptor fitted
NOT 19930
REQUIRED 50mm x 1.75m hose
97
PARTNERSHIPS
Jamie McDonald, “The last thing you need in the heat of a race meet is
Sprint Car Champion for your tools to let you down” Jamie says. “Time and
time again we’ve experienced first hand the massive
Hitachi Power Tools proudly supports Jamie McDonald improvement Hitachi’s technology has given us when it
and the Lawmac Racing team. Hitachi provides the tool comes to working on the car under pressure and severe
technology edge for this high performance Race Team time constraints.”
arguably New Zealand’s most successful and leading
Sprint Car operation.
In Jamie’s first year he won the North Island champs,
the Grand Prix and placed 3rd in the N.Z champs.
Within 3 years Jamie had placed 3NZ, 2NZ and 1NZ,
in that order, meaning he had won every major title
including the Heritage Shield and the Gold Cup.
Since then Jamie has won the Western Springs National
Series twice, The South Island Championship, The
Heritage Shield a further 3 times, BOP Champs, and
last season clocked up his 50th Sprintcar Feature win.
Hitachi’s sponsorship agreement includes outfitting the
team’s inventory of workshop power tools, upgrading
them to the latest state of the art 6.0Ah Cordless and
Brushless motor technology.
98
PARTNERSHIPS
Emirates Team New Zealand
Hitachi Power Tools have supported Emirates Team
New Zealand in every America’s Cup campaign since
1992.
Hitachi Power Tools are used extensively through all
phases of the campaign – from the construction of the
base, right through the boat building process and then
extensively during testing and racing as maintenance
and modifications are required.
Hitachi provides Emirates Team New Zealand with
the latest power tool innovations which has always
allowed the team to work with modern boat building
materials as efficiently as possible.
In the highly competitive world of America’s Cup
racing, technology is king. With Hitachi providing
high-tech lithium-ion cordless tools, with state-of-the-
art brushless motors, team members can undertake
all manner of construction and maintenance tasks,
confident that they have state-of-the-art tool
technology at their fingertips.
99
Ultimate performance,
Unbelievable power.
Hitachi brings
you the most
advanced
power tools.
LIKE US ON
FACEBOOK
HitachiNewZealand
New Zealand Distributor: Accent Tools Ltd, Auckland | [email protected]
The words you are searching are inside this book. To get more targeted content, please make full-text search by clicking here.
HitachiCatalogue2016_iPad
Discover the best professional documents and content resources in AnyFlip Document Base.
Search