CB 750 K7 General information

<i!) HONDA

CB750

TABLE OF CONTENTS

GENERAL INFORMATION 1 II

LUBRICATION 2 mIE1

INSPECTION & ADJUSTMENT 3 II

FUEL SYSTEM 4 II

ENGINE-REMOVAL 5 •11
& INSTALLATION I
=Ill
CYLINDER HEAD/VALVE 6
m
CYLINDER/PISTON 7

CLUTCH 8

CRANKCASE 9

CRANKSHAFT/ 10
CONNECTING ROD

TRANSMISSION 11
FRONT WHEEL/SUSPENSION
12

REAR WHEEL/BRAKE/ 13
SUSPENSION 14

HYDRAULIC BRAKE

BATTERY/ 15
CHARGING SYSTEM

IGNITION 16

ELECTRIC STARTER - 1-7 ·

LIGHTS/SWITCHES 18

TROUBLESHOOTING 19

1 GENERAL ~ HONDA
• INFORMATION GENERAL INFORMATION ~ CB750

GENERAL SAFETY 1-1 TOOLS 1-5
SERVICE RULES 1-1 WIRING DIAGRAMS
1-6
SPECIFICATIONS
TORQUE VALUES 1-2 CABLE & HARNESS ROUTING 1-8

1-4 MAINTENANCE SCHEDULE 1-11

GENERAL SAFETY

• If the engine must be running to do some work, make sure • The battery electrolyte contains sulfuric acid. Protect
the area is well-ventilated . Never run the engine in a eyes, skin and clothing. In case of contact, flush
closed area. The exhaust contains poisonous carbon thoroughly with water and call a doctor if your eyes were
monoxide gas. exposed.

• Gasoline is extremely flammable and is explosive under • The battery generates hydrogen gas which is highly ex-
certain conditions. Do not smoke or allow flames or plosive. Do not smoke or allow flames or sparks near the
sparks in your working area. battery, especially while charging it.

SERVICE RULES

1. Use genuine HONDA or HONDA RECOMMENDED PARTS AND LUBRICANTS OR THEIR EQUIVALENT. Parts that do
not meet HONDA's design specifications may damage the motorcycle.
2. Use the special tools designed for this product.

3. Install new gaskets, 0-rings, cotter pins, lock plates, etc. when reassembling .
4. When torquing bolts or nuts, begin with
diagonally unless otherwise specified. the larger diameter or inner bolt first, and tighten to the specified torque

5. Clean parts in cleaning solvent upon disassembly. Lubricate any sliding surfaces before reassembly.
6. After reassembly, check all parts for proper installation and operation.

7. Use only metric tools when servicing this motorcycle. Metric bolts, nuts, and screws are not interchangeable with
English fasteners. The use of incorrect tools and fasteners may damage the motorcycle.

1-1

~ HONDA GENERAL INFORMATION

~ CB750

SPECIFICATIONS

NOTE: If specifications for the K model are not given, they are the same as the F model.

MODEL ITEM F-MODEL K -MODEL III
DIMENSIONS Overall length
Overall width 2,210 mm (87.0 in.) 2,280 mm (89.8 in.) I
Overall height
Wheel base 860 mm (33.9 in.) 880 mm (34.6 in.) I
Seat height
Foot peg height 1,185 mm (46.7 in.) i
Ground clearance
Ory weight 1,480 mm (58.3 in.) 1,495 mm (58.9 in.) I

830 mm (32.7 in.) 810 mm (31.9 in.)

325 mm (12.8 in.) 330 mm (13.0 in.)

135 mm (5.3 in.) 150 mm (5.9 in.)

232.5 kg (512.6 lbs.) 231 kg (508 lbs.I

FRAME Type Double cradle

Frant suspension Telescopic fork I
141.5 mm (5.6 in.I
Travel I

Rear suspension Swing arm

Front tire size Travel 86.3 mm (3.4 in.) 101 .6 mm (4.0 in.) I
Rear tire size 3.25H-19 (4PR) 3.50H -19 (4PRI
I Front 4 .00H-18 (4PR) 4.50H-17A (4PR) I
Tire pressures
I Rear I
Front brake
Rear brake 2.0/2.25 kg/cm ' (28/32 psi) 2.0 kg/cm' (28 psi) I
Fuel capacity 2 .0/2.8 kg/cm ' (28/40 psi) 2.25/2.8 kg/cm ' (32/40 psi)
Fuel reserve capacity i
Rake angle Dual disc brake Disc brake
Disc brake Internal expanding shoes I
19.5 lit. (5.1 U.S. gal.; 4 .3 Imp. gal.) I
17.5 lit. (4 .8 U.S. gal.; 3.9 Imp. gal.)

4.5 lit. I 1.2 U .S. gal. 1.0 Imp. gal :) 4.0 lit. (1. 1 U .S. gal. 0 .9 Imp. gal.)

27.5° 28°

Trail length 113.5 mm (4.5 in.) 115 mm (4.5 in.)

Front fork oil capacity 135 - 145 cc (5.2 - 5.3 ozs) at draining
145 - 155 cc (5.3 - 5.4 ozs) at disassembly

ENGINE Type Air cooled 4 stroke OHC engine
Cylinder arrangement 4 cylinder in-line
Bore and stroke 61.0 x 63.0 mm 12.402 X 2.480 in.)

Disvl~..;ement 736 CC (44.9 CU in.)

Compression ratio 9.0 : 1

Valve train Chain driven overhead camshaft I
Oil capacity 3.5 lit. (3.7 U.S. qt. 3.1 Imp. qt.)
Lubrication system Forced pressure and dry sump

Cylinder compression pressure

Intake valve open 0° [BTDC)
40° [ABDC)
close

Exhaust valve open 40° [BBDC)

close 0° [BTDC)

Valve clearance IN 0 .05 mm (0.002 in.)
EX 0 .08 mm I0.003 in.)

Engine dry weight 89 kg (196 lbs.)

Idle speed 1,000 ! 100 rpm

.,

GENERAL INFORMATION HONDA

CB750

MODEL ITEM F-MODEL K-MODEL

CARBURA- Carburetor type 4, piston valve, 28 mm
TION Setting number
Pilot screw opening PD 418 PD 41A
DRIVE Float level
TRAIN 1¾ turn 1½ turn
Clutch type 14.5 mm (0.5209 in.I 12.5 mm (0.4921 in.I
Transmission
Wet multi plate

Primary reduction ratio 5 -Speed constant mesh
Gear ratio I 1.708 (Secondary 1.163)

II 2.500
111
1.708
1.333

IV 1.133
0.969
V 3.071 (43/14)
Final reduction ratio 1-N-2-3-4-5, Left foot operated return system

Gear shift pattern Battery and ignition
ELECTRICAL Ignition type 10° (BTDC) 1000 rpm
25° 2500 rpm
Ignition advance F mark Electric or kick starter
Full advance

Starting system J
Alternator
Three phase A .C. generator 12V-0 .21 KW/5,000 rpm
Battery capacity 12V 14AH
Spark plug DSEA (NGK)
X24ES -U (ND)
Spark plug gap
Headlight (low/high) 0.6 - 0.7 mm (0.024 - 0 .028 in.)
Tail/stoplight
LIGHTS Turn signal light 12V 40/50W
Speedometer light 12V 8/27W (3/32 cp.)
Tachometer light
Neutral indicator light 23W (32 cp.)
Turn signal indicater light
High beam indicator light 3.4W (2 cpl
Position light
3.4W (2 cpl

3.4W (2 cpl
3.4W (2 cp)
3.4W (2 cp)

SW (3 cpl

1-3

~ HONDA GENERAL INFORMATION

~ CB750

TORQUE VALUES

• ENGINE

Ref. Item O'ty Thread dia. Torque kg-m (ft-lbs)
No.
1.2 - 1.9 (8.7 - 13.7)
1 Spark plug 4 -- 1.0 - 1.4 (7.2- 10.1)
1.1 -1 .5 (8.0 - 10.9)
2 Valve adjusting hole cap 8 30 2.0- 2.5 (14.5-18.1)
1.8 - 2.2 (13.0 - 15.9)
3 Valve adjusting lock nut 86 10.0- 12.0 (72.3 - 86.8)
2.0- 2.5 (14.5-18.1)
4 Cylinder head nut 16 8 4.0 -4.2 (28.9 - 30.4)
1.8 - 2.2 (13.0 - 15.9)
5 Cam sprocket bolt 27 2.0- 2.5 (14.5-18.1)
1.8 - 2.2 (13.0-15.9)
6 A.C. Generator bolt 1 12 2.7- 3.3 (19.5 - 23.9)
3.5-4.5 (25.3 - 32.5)
7 Starting clutch outer 38 1.5- 2.0 (10.9 - 14.5)
1.0- 1.4 (7.2- 10.1)
8 Clutch canter lock nut 1 16

9 Connecting rod nut 87

10 Crankcase bolt 88
66
11 Crankcase bolt 1 20

12 Oil filter canter bolt

13 Oil drain bolt 1 12

14 Oil pressure switch 1 --

15 Oil pass cap 1 20

• FRAME

Ref. Item O'ty Thread dia. Torque kg-m (ft-lbs)
No.
1 24
1 Steering stem nut 2 7 8.0- 12.0 (57.9 - 86.8)
2 0.9-1.3 (6.5- 9.4)
2 Fork top bridge bolt 6 10 3.0-4.0 (21.7 - 28.9)
3 Fork bottom bridge bolt 1 8 28- 3.3 (20.3 - 23.9)
4 Disk plate setting nut 1 5.5-6.5 (39.8 - 47.0)
4 12 8.0-10.0 (57.9 - 72.3)
5 Front axle nut 1 18 5.5-6.5 (39.8 - 47.0)
3 12 5.5- 7.0 (39.8 - 50.6)
6 Rear axle nut 2 14 5.5-6.5 (39.8 - 47.0)
4 12 4.5- 5.5 (32.5 - 39.8)
7 Final driven sprocket nut 23 2.5-3.5 (18.1 - 25.3)
22
8 Swing arm pivot bolt

9 Engine hanger bolt
10 Fork bolt
11 Oil hose nut

• STANDARDTORQUES

Ref. Item Torque Kg-m (ft-lbs) Ref. Item Torque Kg-m (ft-lbs)
No. No.
5 mm screw 0.35 -0.5 (2.5-3.6)
1 5 mm bolt, nut 0.45- 0.6 (3.3 -4.3) 6 6 mm screw 0.7 -1.1 (5.1 - 8.0)
0.8 - 1.2 (5.8-8.7) 7 6 mm flange bolt, nut 1.0 - 1.4 (7.2 - 10.1)
2 6 mm bolt, nut 1.8-2.5 (13.0-18.1) 8 8 mm flange bolt, nut 2.4 - 3.0 (17.4 - 21.7)
3.0-4.0 (21.7 - 28.9) 9 10 mm flange bolt, nut 3.0-4.0 (21 .7 - 28.9)
3 8 mm bolt, nut 5.0 -6.0 (36.2 - 43.4) 10
'
4 10 mm bolt, nut

5 12 mm bolt, nut

1-4

GENERAL INFORMATION HONDA

TOOLS Tool No. CB750

• SPECIAL TOOLS 07902-2000000 Reference Page
07906-3230000 12-21. 12-22
Ref. 07908-3230000 6-16
No. Tool Name 07909-3000000 6-19
07910-3230101 3- 5
1 48 mm pin spanner 07910- 2830000 12- 8 , 12-11
2 12 mm Box wrench 07910- 3290000 13-6, 13-9
3 Valve adjusting wrench 07914-3230001 13-6, 13-9
4 Spark plug wrench 07916-6390001 14-14
5 Front wheel retainer wrench 07917-3230000 8-5. 8-9
6 Rear wheel retainer wrench 07921-0010000 12-15, 12-17
7 Rear wheel retainer wrench 07922-3000000 14-11
8 Snap ring pliers 07933-3000000 8-5. 8-9
9 16 mm lock nut wrench 07942-3000000 9-3
10 6 mm hollow set wrench 07944- 0980000 6-11
11 Flat nut wrench 07945-3000500 4-7
12 Sprocket holder 07945-3330200 11-7
13 Rotor puller 11-15
14 Valve guide remover installer 07945-3710200 11 - 17
15 Pin driver 07946- 9350200 11-8, 12-9
16 Bearing remover 07946-3290000 13-9
17 Bearing driver 07946-3600000 13- 9
18 Bearing driver 07946-3710400 12-21, 12-22
19 Bearing driver 07947-3290000 12-18
20 Bearing driver 07949-3710000 11-8
21 Bearing driver 07949-6110000 12-9, 13-9
22 Ball race driver 07954- 3000000 7-9
23 Fork seal driver 07957-3290001 6- 10. 6-15
24 Driver handle 07958-3000000 7-9
25 Driver handle 07959-3290000 13- 13
26 Piston ring compressor (21 07984- 6110000 6 - 11
27 Valve spring compressor 07997-0010700
28 Piston base (21 07999-3000000 --
29 Rear shock absorber compressor•
30 Valve guide reamer 7- 9
31 Tool case
32 Rotation bar Reference Page

• OPTIONAL TOOLS 3-11
3-11
_Ref . Tool Name Tool No. 3-11
No. 3-18
07404-0010000 3-18
1 Vacuum gauge set 07510-3000100
07510-3000200
2 Gauge attachment (Al 07506-3000000
07510-3000000
3 Gauge attachment (BI

4 Oil pressure gauge

5 Oil pressure gauge attachment

1-5

WIRING DIAGRAM CD750F U .K. TYPE

IGNITION COIL RE
CON1
R. FRONT TURN SIGNAL LIGHT 12V21W
GROUND I
~~s_ _ _ _,....""""""'_ _ _ _ _ _ _ _ _ _ _ __

INDICATOR LIGHT CLUSTER STARTER ENGINE STOP LIGHTING SWITCH

HIGH BEAM INDICATOR LIGHT FRONT STOP
12V3.4W LIGHT SWITCH

R. TURN SIGNAL
INDICATOR LIGHT

L TURN SIGNAL
INDICATOR LIGHT

OIL PRESSURE

NEUTRAL

HEADLIGHT

TACHOMETER
ILLUMINATING LIGHT

12V3 4W·2-f-f-- - - --f-<I

CLUTCH SWITCH-- - ~ Bk
LG IGNITION SWITCH
TURN SIGNAL HORN
STARTING MOTOR
©d=:_________.
Lo1L PRESSURE
L FRONT TURN SIGNAL LIGHT 12V21 W

TURN SIGNAL HORN DIMMER SWITCH ARRANGEMENT IGNITION SWITCH ARRANGEMENT STARTER ENG

wBL R BAT IG TLl TL 2 PA
L2 HO
Ll PA -o-OFF f--0
N OFF
RUN (}-k)
Rl
PA 0 0
R2

IR STOP LIGHT SWITCH FUSE 5A (TAILLIGHT ) R. REAR TURN SIGNAL LIGHT 12V21 W
ICT BREAKER,
WINKER RELAY
\' \ ~~E IA (HEADLIGHT )
\ 15A (MAIN) r;IJ

r ~ ~ FUSE BOX Bk Gr

DIODE
DIO DE

H
LG/ R

:1

I L - - -,=i Gy
~: ::~ -.R/ W._- ---- ,- 1
·r:===============t====::...-------------------0-c:::J<>--o--- rI I
1---------+----1-+--1,..,_--+...-.111---..,__ _ _ _ _..._...;,.._LB~LB1--__.
11
11

G-8-G = 8 )---&-.._I rt4 TAIL AND STOP LIGHT
.,..., 12V5 / 21W

l- -,.. 11

'"'-=+H-++++""""=~,.,,.,,.,,.,~~................___+-+--.111i1111i1,-_ 11

-- l r~I 11' . . . . . . ........... . . . .. 1I ii . + .rl - " " P " ' - R . . . . , c : ) < ) , , , , - R - -. . .

:i r- , I ....... I

1 11
11
1l__ J l_: : 1I :I1111111:1: I --~ ~
J 11
l t

:::i:: I 11111 11

ILG / R G 1I

BRl~wlrly Y R E G U L A T ~wR I I 1111 1 rID 1I_
I I 11111
Bk
L I 1111:
c::,
i- ~ ~ II

11 111111 1
l7 1
1111
BR wI v!LG/ R
yy 1111
11::
..-LG/R- 1 111
1111
r~ ~i;u, .-------·i'i' ....
1!::

SWITCH RECTIFIER

I • ~01§)

1° ~ I~ ~ L. REAR TURN SIGNAL LIGHT 12V21W

l --It/ITCH STARTER MAGMETIC SWITCH BATTERY
12Vl4AH
ALTERNATOR

~E STOP LI GHTING SW ITCH ARRANGEMENT y Yellow

Br Brown

ST (G) (G) p HL Bk . Black B Blue
Gr ·· Grey
6 6 OFF w Whit e
p 0-K)
LG Light Green LB ·· Light Blue
~ HL 0-rO-K)
R Red 0 Orange

G Green p Pink

00302-410-6100

1-6

CD7SOK WIRING DIAGF

~ FRONT STOP LIGHT SWITCH IGNITION COIL

R FRONT TURN SIGNAL LIGHT 12V211f

~~-;:::::::::::::::::::::::::::::::::::..;-, ll ~

STARTER ENGINE STOP LIGHTING SWITCH

ltfJICATOR LIGHT CLUSTER .1 "'' .I) !!- OR\,111 ..J::l.
HIGH BEAM INDICATOR LIGHT 12V!.IW 1G :nlG
R TURN SIGNAL INDICATOR LIGHT 12 .IW \._ IG ST
L TURN SIGNAL INOICATOR LIGHT 12V3.IW ) ()
OIL PRESSURE LIGHT 12V3.4
!SPEEDOMETER ILLUMINATING LIGHT Br BI Bk R I

Bk W Y R SPARK PLUG
~L .~ ::"'' ~(.(,:::;,L_1 _I, Br/W-
l• -~ )
.. .....---+t-4._ n :~lLJ...1,.1
L.--++--11,l< -~ YIR ,-------, BkGY

: ......-/-RBki : I- lL_____ [

1 .lll!E' --~BkEll</W I J

NEUTRAL INDICATOR LIGHT 'V"~=--!__J---, ----1Bk .=_ ; I ..,L_ ____J t - - - - - - s

~ G -rt+-+--+-+------11+-:[=::J<>-=i=...'._-,-Bk II .-.---+--+-----------------·
h r-+------G G-
HEADLIGHT
12V60W55W tlr\..~"'-ol,:,l~Bkl-,--1-t++-, ~>-LB-+-- ,
~~l~ON LIGHT - BI R-,- Br//w- 11--1.....;t--t--
Br. B-+1--+--4--lt-- --+- +- +------------I'

>-0-
I'"W

-----Br/B

./
Y-t~/
._., LG/R- .J _
~
I-, I ~

Br G- - s - - + - - + - - - + - - - - - - -

11 ~ r I

I

Br /R...µ
Br Br-...--1-'t+t-+t-t-,
w I _/R- + -

TACHOMETER ILLUMINATING L I G H T . - G,-_.:_____."""'------++-... LG/R----++---+-+-+-+-+-t_. 11:,- - - - 'c. _
12V3.IW ·2 ~ i-=B rLBl:_R:~-!~-;-!j~~...I
Br/W G i=O--l.....-

~ - L G - - ~ - - - _ --__ - _ -~-+-....._ .,1

L-- ~

CLUTCH SWITCH~R

-Br/B - - I 1Br Bk

B,/R LB Gr LG / , B, w

------------------:~ i I l!;:l
~~ ~Nt2.?2il
lJIPL TLHLI 1G a,

I0 00 0 01

IGNITION SWITCH

STARTING MOT<

TURN SIGNAL HORN OIMMER SWITCH OIL PRESSURE SW

cw=:-.-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-:_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-:_" "_. .

L FRONT TURN SIGNAL LIGHT 12V21 W

TURN SIGNAL HORN DIMMER SWITCH ARRANGEMENT IGNITION SWITCH ARRANGEMENT STARTER ENGINE STOP LIGHTING SWITCH ARRANGO

WB L R BAT IG TLI TL2 PA
L2
LI LOCK
N
RI OFF '~--··
R2 0
RUN 0 f-0 0--0--
1-7 PA 0 -

I REAR STOP LIGHT SWITCH FUSE BOX
FUSE 7A (TAILLIGHT)
CONTACT BREAKER ANO CONDENSER FUSE 7A (HEADLIGHT)
r FUSE IIA (MAIN)

SILICON R. REAR TURN SIGNAL LIGHT 12V2lll

1, WINKER RELAY ~

'1 R LG/ R LB
11
I II I i
iM \j II
JI I IL _______ .JI II
wH 11 II
B Y rl !-, L _______ 11
II :I IL ______ JI
_J L-------
ii TAIL ANO STOP LIGHT 12V l /2IW
r - - - - - .....
~L - ==::..
II
II 11 LB-c::::J<>--LB
I 11
J 11 / O-c::::J<>--01----
Bk G-ao-G
I 1 =--
L...ci Br-c::::J<>--Br
R/ '11 1 ,I ,1 i

r-------., r---- 11
1I
II II r~
II
II II I
JI
I
I I
L I

I ~
-=-
I
L REAR TURN SIGNAL LIGHT 12V21 W

LR

SW ITCH

ALTERNATOR

Br ·· Br own y Yellow

ENT BI< Black B Blue

w Whit e Gr · Grey

LG Light Green LB Light Blue

R Red 0 Orange
G Green p Pirl<

00302-405-6100

GENERAL INFORMATION ~ HONDA

CABLE AND HARNESS ROUTING ~ CB750

CABLE AND WIRE HARNESS ROUTING

(3) TURN SIGNAL RELAY
(4) DIODE

(2) SILICON RECTIFIER (5) VOLTAGE REGULATOR
(6) STARTER MAGNETIC SWITCH
(1) BATIERY BREATERTUBE (7) FUSE BOX
(2) CRANKCASE BREATHER DRAIN TUBE (4) FUEL TANK OVERFLOW TUBE
(3) CARBURETOR OVERFLOW TUBE
()/(5) TO AIR CLEANER
ENGINE RIGHT
NEUTRAL SWITCH CORD ROUTING

1-8

~ ,HONDA. GENERAL INFORMATION

~ CB750
·r

CABLE AND WIRE HARNESS
ROUTING

(1) CLUTCH CABLE (5) BRAKE HOSE
(6) FRONT BRAKE STOPLIGHT SWITCH WIRE
(2) CLUTCH SWITCH WIRE
(3) TURN SIGNAL
SWITCH WIRE

(4) WIRE BANDS (7) STARTER KILL SWITCH WIRE
(8) THROTILE CABLES

(1) FRONT BRAKE STOPLIGHT SWITCH WI RE--~~~~~~
(2) THROTILE CABLE (CLOSE SIDE)
(3) THROTILE CABLE (OPEN SIDE)
(4) STARTER KILL SWITCH WIRE

(1) CLUTCH CABLE

(2) LEFT TURN SIGNAL WIRES
(3) CHOKE CABLE

ic.:======-- (4) THROTILE CABLES

(5) SPEEDOMETER CABLE

1-9

GENERAL INFORMATION ~ HONDA

~ CB750

MAIN HARNESS ROUTING

(1) MAIN HARNESS (2) REAR HARNESS

(4) TO AC . GENERATOR

CABLE ROUTING

1-10

Ci)\ HONDA GENERAL INFORMATION

~ CB750

,-...

MAINTENANCE SCHEDULE

(3) 1) 1 month 2) 12 months This maintenance schedule is based upon average
(4) 500 miles 500 miles 6,000 miles riding conditions. Machines subjected to severe use,
(5) 1,000 km 1,000 km 3 months 6 months 10,000 km or ridden in unusually dusty areas, require more
(6) 1,500 miles 3,000 miles frequent servicing.
* (7) R 32) 2,500 km 5,000 km C (1) IWTIAL SERVICE PERIOD
* (8) R (2) REGULAR SERVICE PERIOD
* (9) I& L R R Perform at every indicated month or mileage
(10) I R interval, whichever occurs first .
I **R (3) ENGINE OIL
(11 I I I (4) OIL FILTEA ELEMENT
I R (5) OIL FILTEA SCREEN
* (12) I I I (6) SPARK PLUG
(13) I I (7) CONTACT POINTS AND IGNITION Tllv.lNG
IC (8) VALVE TAPPET CLEARANCE
* (14) I (9) CAM CHAIN TENSION
(15) I& L !I (10) AIR FILTER ELEMENT
(11) AIR FILTER BREATHER ELEl\.1ErJT
* (16) I I (12) CARBURETOR
(17) I (13) THROTTLE OPERATION
(18) I C (14) FUEL FILTEA SCREEN
I I (15) FUEL LINES
* (19) I I (16) CLUTCH
* (20) ***R (17) DRIVE CHAIN
I (18) BRAKE FLUID LEVEL
(21) I (19) BRAKE FLUID
* (22) I I (20) BRAKE SHOES/ PADS
I (21) BRAKE CONTROL LINKAGE
(23) I I (22) WHEEL RIMS AND SPOKES
(24) I (23) TIRES
(25) (24) FRONT FORK OIL
(26) I (25) FRONT Al'JD REAR SUSPENSIOtJ.
* (27) I& L (26) REAR FORK BUSHING
(28) (27) STEERING HEAD BEARINGS
(29) I (28) BATTERY
* (30) I (29) LIGHTING EQUIPMENT
(31) I (30) SIDE STAND
I (31) ALL NUTS, BOLTS, AtJD OTHER FASTENERS
(32) Service more frequently if operated in dusty areas .

Items marked (*) should be serviced by an
authorized Honda dealer, unless the owner has
proper tools and is mechanically proficient. Other
maintenance items are simple to perform and may
be serviced by the owner.
** Service period: 20,000 km (12,000 miles)

or 12 months
*** Initial service period: 2,500 km

(1,500 miles)
I - Inspect, clean,adju~t or replace if necessary
R- Replace
C- Clean
L - Lubricate

1-11