MAN Spare Parts Catalogue

MAN Diesel & Turbo

Technical Documentation
Engine
Spare Parts Catalogue

Engine ................................................ V28/33D
Works No. of engine ........................... 1062105

1062106
Plant No. ............................................ 4301599

2012-09-17 - de

010.005

Translation of the original instructions

6741 -01 EN 1 (2)

MAN Diesel & Turbo

MAN Diesel & Turbo SE
86224 Augsburg
Phone +49 (0) 821 322-0
Fax +49 (0) 821 322-49 4180
[email protected]
www.mandieselturbo.com/primeserv
Copyright © 2012 MAN Diesel & Turbo
All rights reserved, including reprinting, copying (Xerox/microfiche) and translation.
2 (2) 6741 -01 EN
010.005
2012-09-17 - de

2012-09-17 - de MAN Diesel & Turbo

Table of contents Table of contents

1 Introduction 1 (3)

1.1 Preface
1.2 Spare Parts Catalogue as Technical Documentation Compo-

nents
1.3 Structure and use of the Spare Parts Catalogues
1.4 Parts replacement service
1.5 Spare parts ordering
1.6 Identification of delivered spare parts
1.7 Available spare parts kits

2 Sub-assembly overview

2.1 Sub-assembly overview

3 Spare Parts (Engine)

011.05 Oil sump
011.06 Dipstick
012.06 Casing feet
012.07 Cylinder crankcase
020.03 Crankshaft
021.03 Main bearing
026.03 Turning gear
027.03 Vibration damper
030.04 Connecting rod
034.02 Piston rings
034.05 Piston
050.04 Cylinder liner
051.02 Water-conducting sleeve
055.05 Cylinder head
057.01 Safety valve
059.01 Cylinder head cover
070.04 Cover of charge air inlet casing
071.01 Dead centre indicator
071.03 Covering on coupling end
072.02 Covering on free end of engine
073.08 Covering on injection pumps
073.09 Covering of crankcase with splash-oil
077.02 Covering of camshaft
100.01 Camshaft drive
101.06 Camshaft
102.01 Camshaft bearing
111.01 Valve drive
112.01 Tappet
171.03 Compressed air starter with attachments

6741 -01 EN

Table of contents MAN Diesel & Turbo

2012-09-17 - de 200.02 Fuel injection pump
221.01 Fuel injection valve with injection nozzle
280.11 Air by-pass piping
280.18 Drain pipes
280.23 Charge air pipe
280.24 Charge air pipe
280.26 Control air pipe
280.27 Control air pipe
280.28 Control air pipe
286.05 Attaching parts for turbocharger
289.04 Exhaust pipe
289.05 Intermediate flange
292.04 Insulation exhaust pipe
292.05 Covering of the exhaust gas pipe
300.07 Mounting of the lube oil pump
300.10 Lubrication oil pump
310.01 Lube oil filter
310.03 Lube oil filter
311.01 Crankcase venting
311.02 Crankcase venting
312.03 thermostat
320.03 Lubricating oil cooler
322.05 Charge air pipe
322.08 Charge air cooler
350.05 Water pump
350.07 Sea water pump
350.08 Cooling water pump with attachments
350.09 Cooling water pump with attachments
400.01 Mounting of speed pick-up
403.04 Engine sensoring system
403.05 Pressure transducer with attachment
408.02 Monitoring of main bearing temperature
409.04 Exhaust gas temperature monitoring
411.01 Cooling water thermostat
413.04 Splash Oil Temperature Monitoring
432.01 Starting air pipe
433.07 Fuel injection pipe
433.08 Fuel pipe
433.10 Fuel pipes on free end of engine
433.11 Vibration damper
440.05 Lubricating oil pipe
440.08 Valve seat lubrication
440.10 Metallic particle sensor with fixture
440.11 Valve seat lubrication
440.12 Valve seat lubrication

2 (3) 6741 -01 EN

MAN Diesel & Turbo

441.08 Pressure gauge pipe
441.10 Pressure gauge pipe
444.03 Counter flange
446.03 Lubricating oil pipe to the turbocharger
446.04 Pipes to the turbocharger
447.17 Coolant bleeding
447.18 Cooling water pipe
447.19 Coolant bleeding
489.01 Warning sign
489.07 Mounting of terminal box
489.09 Cable guiding rail

4 Spare Parts (Tools)

5 Spare Part Kits (SPK)

SPK0008.01 Spare Parts Kit - Seal Kit Cylinder Head
SPK0009.01 Spare Parts Kit - Seal Kit Cylinder Head
2012-09-17 - de

Table of contents

6741 -01 EN 3 (3)



MAN Diesel & Turbo

1 Introduction
2 Sub-assembly overview
3 Spare Parts (Engine)
4 Spare Parts (Tools)
5 Spare Part Kits (SPK)

2012-09-17 - de

Introduction

6741 1-01 EN 1 (1)



MAN Diesel & Turbo 1.1

Preface Introduction

Spare Part/Spare Parts Catalogue

Maintenance and repair work can only be carried out properly and correctly if
the required spare parts are available. The spare parts are to be kept at
stock or ordered in due time. The required order numbers can be found in
Spare Parts Catalogues. The Spare Parts Catalogue for engine is available
for you.
Organization structure of this Spare Parts Catalogue is explained in section
1.3. Order numbers for spare parts of turbocharger, measuring, control and
regulating devices, as well as for engine and system accessories, can be
found in other components of the Technical Documentation. Also see
instructions in Section 1.2.
With best regards
MAN Diesel & Turbo SE

2011-07-14 - de Introduction

General

6684 1.1-01 EN 1 (1)



MAN Diesel & Turbo 1.2

Spare Parts Catalogue as Technical Documentation Components Introduction

Overview

For spare parts ordering and for identification of components in the scope of
supply of MAN Diesel & Turbo are provided Spare Parts Catalogues. Some
of required data can be found in other information sources. The following
components are available in the Technical Documentation system :

Components/Sub-assemblies Information sources Volume of Technical Documentation

Engine Spare Parts Catalogue 010.005 Engine - Spare Parts Cata-
logue

Turbocharger Spare Parts Catalogue 010.200 Turbocharger

Tools (Engine) Data in Work Cards 010.005 Engine - Work Instructions

Spare Parts Catalogue 010.005 Engine - Spare Parts Cata-
logue

List 015.010 Engine tools

Tools (Turbocharger) List in the turbocharger’s tool case /

Data in Work Cards 010.200 Turbocharger

Measuring, control and regulation List of measuring and regulation devi- 010.290 Engine control and monitor-
devices ces ing

Engine and system accessories Spare Parts Catalogue/Spare part 020 ... Plant systems
sheet depending on manufacturer
and product

Table 1: Spare Parts Catalogue and comparable information sources

Spare parts for engines and turbochargers

Spare parts for engines and turbochargers can be identified with the aid of
the spare parts catalogues in Volume 010.005 Engine - Spare Parts Cata-
logue and Volume 010.200 Turbocharger of Technical Documentation. An
illustrated sheet is provided in each case to guide you, using the item num-
bers to indicate you the order number. The spare parts sheets are ordered
according to sub-assemblies.

Spare parts for tools/Ordering of tools (engine)

Complete tools and spare parts for them can be ordered from Spare Parts
Catalogue in Volume 010.005 Motor - Spare Parts Catalogue (Section 4) or
from tool list in Volume 015.010 Engine tools of the Technical Documenta-
tion. The tool numbers can be also taken from relevant Work Cards in Vol-
ume 010.005 Engine - Working Instructions.

2011-07-14 - de Spare parts for tools/Ordering the tools (turbocharger) Introduction

Complete tools can be ordered from the contents list in the turbocharger tool General
case. The order numbers can also be found in the respective Work Cards in
Volume 010.200 Turbocharger. It is also possible to identify/order individual
parts for tools in this way.

6684 1.2-01 EN 1 (2)

Introduction1.2 MAN Diesel & Turbo

Introduction Spare parts for measuring, control and regulation systems 2011-07-14 - de

General For data on spare parts for measuring, control and regulation devices, e.g.
temperature sensors, relays, measuring transducers, pneumatic and
hydraulic valves, refer to documentation in Volume 010.290 Engine control
and monitoring, particularly to "List of measuring and regulation devices" and
to "Control scheme".

Spare parts for engine and system accessories

Data on spare parts for engine and system accessories, e.g. oil mist detector
and system accessories, e.g. filters, separators, water-softening plants etc.
refer to documentation in Volumes 020 .... Plant systems. This documenta-
tion contains Spare Parts Catalogue and Spare Parts Lists of the relevant
suppliers.
For ordering the spare parts or in case of any problems with these parts,
please contact MAN Diesel & Turbo or our authorised Service Support Facili-
ties. In this way you will remedy your guarantee claims. On the other hand,
we guarantee that you will get only original spare parts.

2 (2) 6684 1.2-01 EN

MAN Diesel & Turbo 1.3

Structure and use of the Spare Parts Catalogues Introduction 1 (2)

Tips for use The Spare Parts Catalogue contains
▪ all main parts of engine,
What does the Spare Parts ▪ pipings ≧ nominal width 10 mm,
Catalogue contain? What ▪ parts, which are used in operating device and in relevant pneumatic and
does not contain?
hydraulic systems, and
What to do when parts are ▪ tools with their spare parts.
not found? The Spare Parts Catalogue does not contain
Validity/Error sources ▪ subordinate or plant-specific insulations/coverings and
▪ subordinate wirings or wirings outgoing from engine/carried out by oth-

ers.
If parts are to be ordered, which are not contained in the Spare Parts Cata-
logue or were not found, please describe part and installation place as
exactly as possible. Send also a digital photo, if necessary. For parts of sub-
suppliers, which are found in their documentation, indicate also the type
plate content. Also observe notes under keyword "Illustration/Allocation of
adjacent parts" at the end of this Section.

Spare Parts Catalogues are tailored to the specific engine type. This Spare
Parts Catalogue is applicable only for engine or engine group with factory
number or factory number group indicated on the cover sheet.

Transferability of Spare Parts Catalogues

Spare Parts Catalogues may not be transferred from one engine to
another.

Replacement sheets Due to order-specific handling of the Spare Parts Catalogue the further
Further error sources change management is as a rule not required. Nevertheless, if you will
Supply of changed parts receive supplementary sheets or replacement sheets, these will have a great
importance. Please observe that supplementary and replacement sheets are
included in all available Spare Parts Catalogues.
If, during operation period the engine is subjected to changes, for which
MAN Diesel & Turbo has not made out any new drawings or a relevant spare
part sheet, the engine operator shall himself make a warning note in the
Spare Parts Catalogue. Thus will prevent wrong orders.
Due to further development of engines in case of later orders under certain
circumstances the spare parts will be supplied, which are changed in com-
parison to the original ones, and which nevertheless perform the same func-
tion.

2011-07-14 - de Structure and special features Introduction

Sheets of the Spare Parts Catalogue are arranged according to the engine General
sub-assembly system. Sub-assembly overview is an integral part of the fol-
lowing section. This overview consists of sectional views and of a table,
which are arranged according to the sub-assembly numbers.
The tool sheets are assorted as follows:
▪ Basic tools/General purpose hydraulic tools of (980),

6684 1.3-01 EN

1.3 MAN Diesel & Turbo

Introduction Sub-assemblies ▪ standard tool for working on specific sub-assemblies (981),
Index number ▪ additional tools supplied upon the customer's request (982).
Spare parts catalogue sheet Sub-assemblies with their numbers in brackets are available not for all
number engines. Sub-assemblies with numbers marked with *, are not visible in the
Position number sub-assembly overview. They have an arrow there.
The index number on the top right in the spare parts sheets consists of a
Order number three-digit sub-assembly number and a variant number, which corresponds
to the design version.
Letters in order numbers The spare parts catalogue sheet number consists of the print number 6... on
the bottom left and of the index number on right, next to it.
Spare part designation The position numbers of the spare part drawings are repeated in the spare
Orientation support part tables. They lead to order number and to designation of the spare part.
Illustration/Allocation of For tool sheets, two cases should be distinguished:
adjacent parts The tool can consist of one unit, e.g. of 111.126 for sub-assembly 113/114,
or of a group of units as for sub-assembly 113..148.
Introduction In the spare part table these positions are marked with -->. 2011-07-14 - de
In the cases when there is a numerical combination in brackets after the
General position number, an independent tool is meant, which may be also used for
another sub-assembly.
The order numbers in the second column of the spare part table consist of a
sub-assembly, variant, and position number. A letter like in the first column
may also stand for the position number.
The order numbers of tools are identical to the stamped tool number, or con-
sist of a tool group number plus position number.
Letters occur in the order numbers for engine components, when
▪ components belong to pre-assembled groups,
▪ process relative units are aggregated,
▪ a greater range width of specifications can occur, e.g. for piston rings,

injection valve and injection pump elements.
The assignment of the proper specification to the engine concerned is made
by MAN Diesel & Turbo on basis of relative engine parameters.
The spare part designation describes the relative component or sub-assem-
bly.
As orientation support for spare part drawings, scaled down illustrations of
the engine or details are provided.
The number of sub-assemblies is relatively small, i.e. the probability of wrong
change-overs/doubtful cases whether a part belongs to the suspected or
adjacent group is also very low. Observe the following rules of illustration/
allocation:
▪ Studs belong to the part where they are screwed in. Therefore, bolts of

the main bearing belong to the crankcase exactly the same way as the
cylinder head bolts.
▪ Bushes/sleeves/pins belong to the part in which they are pressed in.
Therefore, the water-carrying insert comprising the fuel injection valve
and the sleeves fitted above it belong to the cylinder head exactly the
same way as valve seat rings of inlet and exhaust valves.
▪ O-rings/sealing rings belong to the part, which is provided with the rela-
ted groove.

2 (2) 6684 1.3-01 EN

MAN Diesel & Turbo 1.4

Parts replacement service Introduction

Parts replacement service for high-value components

For high value components, which have become defective or worn, and the
reconditioning or repair of which requires special know-how or facilities, we
offer a parts replacement service. This is provided for following components:
▪ cylinder heads,
▪ Piston crowns,
▪ Valve cages and valves,
▪ Fuel injection nozzles and injection pumps,
▪ Speed governors,
▪ Compressed air starter/Starter and
▪ completely assembled rotors of turbochargers (cartridges).
These parts can generally be delivered ex-stock. If not, they will be recondi-
tioned/repaired and returned to you. Please ask MAN Diesel & Turbo or the
nearest Service Centre to submit a quotation tailor-made to your needs
whenever required.

2011-07-14 - de Introduction

General

6684 1.4-01 EN 1 (1)



MAN Diesel & Turbo 1.5

Spare parts ordering Introduction

Spare parts ordering - data required

Data required To avoid queries, we ask to indicate following data when ordering spare
parts:

Engine type xxxxxxxxx
Factory number of the engine x xxx xxx
Part designation xxxxxxxxx
Order number xxx.xx.xxx
Number required xx
Destination address xxxxxxxxx
Shipping method xxxxxxxxx

Address Please address your order to
24 hour hotline
Tel: +49 1801 15 15 15

Company headquarters MAN Diesel & Turbo SE
Augsburg 86224 Augsburg
Germany
Technical Service Tel: +49 821 322-0
Spare parts Fax: +49 821 322-3382
E-mail: [email protected]
24-hour hotline
Tel: +49 821 322-1499
Fax: +49 821 322-3838
E-mail: [email protected]
24-hour hotline
Tel: +49 821 322-1799
Fax: +49 821 322-3574
E-mail: [email protected]

2011-07-14 - de Introduction

General

6684 1.5-01 EN 1 (1)



MAN Diesel & Turbo 1.6

Identification of delivered spare parts Introduction

New parts - Service parts

Prior to shipment the spare parts are marked. This is made with identification
cards.

Identification card of new The identification card of new parts is used for parts, which are delivered in
parts connection with the original scope of supply.

Identification cards of Figure 1: Identification card for new parts
service parts Identification of parts can be made on basis of Catalogue-no. of Spare Parts
Catalogue for SPARE PARTS, as well as on basis of Catalogue-no. of Tool
and Reserve Parts List for TOOLS and ADD SPARE PARTS
The identification card of service parts is used for parts, which are delivered
within the scope of service work.

2011-07-14 - de Introduction

General

6684 1.6-01 EN 1 (2)

Introduction1.6 MAN Diesel & Turbo

Introduction Figure 2: Identification card for service parts 2011-07-14 - de
The identification card allows to make conclusions on the underlaid order,
General and contains among other things the catalogue number and part designa-
tion.

2 (2) 6684 1.6-01 EN

MAN Diesel & Turbo 1.7

Available spare parts kits Introduction

Spare parts kits in Spare Parts Catalogue

Components of a spare parts Spare parts kits contain parts packages that have been specially tailored for
kit maintenance or overhaul jobs. The components of a spare parts kit often
include several engine sub-assemblies that can of course also be ordered as
individual parts under the relevant sub-assemblies in the spare parts cata-
logue.

Available spare parts kits Figure 1: Example of a spare parts kit – set of seals for cylinder head sub-assembly
The spare parts kits that are currently available are listed in the final section
of this spare parts catalogue. In addition, information on available spare parts
kits is also provided in the sections of the spare parts catalogue for the rele-
vant sub-assemblies.

2011-07-14 - de Introduction

Figure 2: Example of a spare parts kit – set of seals for cylinder head sub-assembly General
6684 1.7-01 EN
1 (2)

1.7 MAN Diesel & Turbo

Introduction Advantages of spare parts The advantages of spare parts kits are illustrated here using the set of seals
kits for the cylinder head sub-assembly as an example:
Other spare part kits are ▪ All the seals required to carry out maintenance work on the cylinder head
available on request
and neighbouring sub-assemblies are supplied in one kit.
▪ Allocation of seals and sealing rings is easier.
▪ Simplified handling, management and storage of spare parts.
Other spare parts kits may already be available or can be specially compiled
on request. If you have any questions, feel free to contact our Technical
Service at any time.

Introduction 2011-07-14 - de

General

2 (2) 6684 1.7-01 EN

MAN Diesel & Turbo

1 Introduction
2 Sub-assembly overview
3 Spare Parts (Engine)
4 Spare Parts (Tools)
5 Spare Part Kits (SPK)

2012-09-17 - de

Sub-assembly overview

6741 2-01 EN 1 (1)



MAN Diesel & Turbo 2.1

Sub-assembly overview Sub-assembly overview

Assembly overview - cross section and longitudinal section of the engine

2012-07-16 - de Figure 1: Cross section of the engine Sub-assembly overview
6741 2.1-02 EN
V28/33D

1 (4)

Sub-assembly overview2.1 MAN Diesel & Turbo

Sub-assembly overview Figure 2: Longitudinal section of engine 2012-07-16 - de
2 (4) 6741 2.1-02 EN
V28/33D

MAN Diesel & Turbo 2.1

List of assemblies - designation Sub-assembly overview 3 (4)

2012-07-16 - de Sub-assembly Designation Sub-assembly overview
011 Oil sump
012 Cylinder crankcase V28/33D
020 Crankshaft
0211) Crankshaft bearings
0261) Turning motor
0271) Torsional vibration damper
030 Connecting rod
034 Piston
050 Cylinder liner
051 Water-conducting sleeve
055 Cylinder head
059 Cylinder head cover
0701) Casing of the emergency stop device
0711) Clutch end casing
0721) Non-clutch end casing
073 Crankcase casing with relief valve / splash oil
077 Casing of camshaft
100 Control device operating mechanism
101 Camshaft
1021) Camshaft bearings
111 Valve train
112 Tappet attachment
1131) Inlet valve
114 Exhaust valve
1711) Compressed air starter
200 Fuel injection pump
221 Fuel injection valve
280a Emergency stop device
280b Charge air pipe
280c1) Bypass flap
286 Turbocharger attachment
289 Exhaust pipe
292 Exhaust pipe casing
3001) Lubricating oil pump
3101) Lube oil filter
311 Crankcase ventilation

6741 2.1-02 EN

2.1 MAN Diesel & Turbo

Sub-assembly overview Sub-assembly Designation

3121) Lubricating oil thermostat

320 Lubricating oil cooler

322 Charge air cooler

3501) Cooling water pump

4001) Speed sensor

403 Engine sensors

408 Main bearing temperature monitoring

409 Exhaust gas temperature sensor

419 Indicator valve

433a Fuel pipe

433b Fuel line casing

440 Lubricating oil pipe

4411) Pressure gauge pipe

4441) Counter-flange

447 Cooling water line

4891) Cable conduit rail

4991) Labelling

Table 1: Sub-assembly designation

1) These sub-assemblies cannot be seen in the pictures

Sub-assembly overview 2012-07-16 - de

V28/33D

4 (4) 6741 2.1-02 EN

MAN Diesel & Turbo

1 Introduction
2 Sub-assembly overview
3 Spare Parts (Engine)
4 Spare Parts (Tools)
5 Spare Part Kits (SPK)

2012-09-17 - de

Spare Parts (Engine)

6741 3-01 EN 1 (1)



2012-07-26 - de 1 (8) 6741 01

Oil sump

V28/33D

11.05 EN MAN Diesel & Turbo

6741 011.05

2012-07-26 - de Oil sump

V28/33D

2 (8) 6741 01

6741 011.05

11.05 EN MAN Diesel & Turbo

2012-07-26 - de 3 (8) 6741 01

Oil sump

V28/33D

11.05 EN MAN Diesel & Turbo

6741 011.05

2012-07-26 - de Oil sump

V28/33D

4 (8) 6741 01

6741 011.05

11.05 EN MAN Diesel & Turbo

5 (8) 6741 01

Pos. No. Order No. Item designation
001 1) 011.05.001 Oil sump with items B01, B04 to B07, B10, B14 to B22
engine
002 1) 011.05.002 Oil sump with items B02, B04 to B07, B10, B14 to B22
engine
2012-07-26 - de 003 1) 011.05.003 Oil sump with items B03 to B07, B10, B14 to B22, B30
031 011.05.031 Oil sump with items B04 to B23 for 12 cylinder engine
B01 011.05.B01 Oil sump
B02 011.05.B02 Oil sump
B03 011.05.B03 Oil sump
B04 011.05.B04 Suction plate
B05 011.05.B05 Sieve
B06 011.05.B06 Hexagon bolt
B07 011.05.B07 Pipe
B08 011.05.B08 Pipe
B09 011.05.B09 Pipe
B10 011.05.B10 Pipe coupling
B11 011.05.B11 Non-return valve
B12 011.05.B12 Seal
B13 011.05.B13 Hexagon bolt
B14 011.05.B14 Hexagon nut
B15 011.05.B15 Hose clamp
B16 011.05.B16 Hexagon bolt
B17 011.05.B17 Hose clamp
B18 011.05.B18 Hexagon bolt
B19 011.05.B19 Supporting sheet
B20 011.05.B20 Supporting sheet

Oil sump

V28/33D

11.05 EN Quantity MAN Diesel & Turbo
Unit
2, B30 to B35 for 20 cylinder
2, B30 to B35 for 16 cylinder
0 to B35 for 12 cylinder engine
(depth 775)

6741 011.05

Oil sump

V28/33D

2012-07-26 - de Pos. No. Order No. Item designation
B21 011.05.B21 Washer
B22 011.05.B22 Hexagon bolt
B23 011.05.B23 Oil sump
B30 011.05.B30 Pipe
B31 011.05.B31 Non-return valve
B32 011.05.B32 Pipe coupling
B33 011.05.B33 Seal
B34 011.05.B34 Hexagon bolt
B35 011.05.B35 Pipe
004 011.05.004 Stud
005 011.05.005 Suction pipe
006 011.05.006 O-ring seal
007 011.05.007 Cylindrical screw
008 987.01.102 Hylomar SQ/M
009 011.05.009 Valve
010 011.05.010 Hexagon nut
011 011.05.011 Flange
012 011.05.012 Seal
013 011.05.013 Hexagon bolt
014 987.01.204 Loctite 245
015 011.01.A Blocking tool with items A01 to A07
A01 011.01.A01 Adapter
A02 011.01.A02 Spring
A03 011.01.A03 Washer
A04 011.01.A04 Sleeve

6 (8) 6741 01

Quantity 6741 011.05

Unit

11.05 EN MAN Diesel & Turbo

7 (8) 6741 01

2012-07-26 - de Pos. No. Order No. Item designation
A05 011.01.A05 Seal
A06 011.01.A06 Sealing ring
A07 011.01.A07 Sealing ring
016 011.05.016 Seal
017 011.05.017 Seal
018 011.05.018 Seal for 20-cylinder engine
019 011.05.019 Seal for 16-cylinder engine
020 011.05.020 Seal for 12-cylinder engine
021 011.05.021 Sealing cord for 20 cylinder engine
022 011.05.022 Sealing cord for 16-cylinder engine
023 011.05.023 Sealing cord for 12-cylinder engine
025 011.05.025 Pipe
026 011.05.026 O-ring seal
027 011.05.027 Washer
028 011.05.028 Cylindrical screw
029 011.05.029 Washer
030 011.05.030 Hexagon nut
040 011.05.040 Flange
041 1) 011.05.041 Non-return valve
042 1) 987.01.206 Loctite 270
051 2) 011.05.051 Oil sump with items D01, D04 to D08, D10, D11 for 12
052 2) 011.05.052 Oil sump with items D02, D04 to D08, D10, D11 for 16
053 2) 011.05.053 Oil sump with items D03 to D11 for 20 cylinder engine
D01 011.05.D01 Oil sump
D02 011.05.D02 Oil sump

Oil sump

V28/33D

11.05 EN MAN Diesel & Turbo
Unit
Quantity

2 cylinder engine
6 cylinder engine

6741 011.05

Oil sump

V28/33D

Pos. No. Order No. Item designation
D03 011.05.D03 Oil sump
D04 011.05.D04 Suction plate
D05 011.05.D05 Sieve
D06 011.05.D06 Hexagon bolt
D07 011.05.D07 Pipe
D08 011.05.D08 Pipe coupling
D09 011.05.D09 Pipe
D10 011.05.D10 Hose clamp
D11 011.05.D11 Hexagon bolt

Note 1) Depth 815
2) Depth 550

2012-07-26 - de

8 (8) 6741 01

Quantity 6741 011.05

Unit

11.05 EN MAN Diesel & Turbo

2012-07-26 - de 1 (2) 6741 01

Dipstick

V28/33D

11.06 EN MAN Diesel & Turbo

6741 011.06

Dipstick

V28/33D

Pos. No. Order No. Item designation
A 011.06.A Dipstick with items A10 + A11
A10 011.06.A10 Handle
A11 011.06.A11 Spring pin
010 011.06.010 Sealing ring
020 011.06.020 Spacer
B 011.06.B float switch
C 011.06.C float switch

2012-07-26 - de

2 (2) 6741 01

Quantity 6741 011.06

Unit

11.06 EN MAN Diesel & Turbo