YG 2019

TECHNICAL TECHNICAL
DATA SUPER CUTTING END MILLS DATA SUPER CUTTING END MILLS





13 Combination Shanks for End Mills 16 Troubleshooting in Endmilling


Right hand End Mill shank shown. For Trouble Occurrences of trouble Countermeasures
left hand End Mills flat “F” and pin
groove “K” should be located 180° from •At time of engaging with work material 1. Decrease feed rate.
that shown, maintaining 12° relationship G •When ending cut 2. Decrease projection amount
of flat “F” and groove “K” 3. Shorten cutting edge length to required minimum limit


K F 45° •During normal cutting 1. Decrease feed rate
E 2. Control wear → replace tool early
L 3. Replace chuck or collet
B 4. Decrease projection amount
Breaking of tool 5. Carry out honing
90° 1/2K H C 45° 6. If 4 flute, reduce to 2 flute(clogging of chipping)
7. If dry cutting change to wet cutting utilize cutting fluid. In case of wet
cutting flow oil supplied from the front, change to from rear angle
A J D of side top. Use ample with rate.
•When changing direction of feed 1. Utilize circular interpolation(in case of NC machine) or temporarily
.015 stop feed(Dowelling)
M CENTRAL WITH “K”
12° 2. Reduce feed rate before and after change of directions
3. Replace chuck or collect
14 Dimensions
•Fracture of corners 1. Carry out chamfering or nose with hand lapper.
All dimensions are given in inches. 2. Down cut → Up cut

Diameter Length •Fracture at boundary of depth of cut 1. Down cut → Up cut
of Shank of Shank B C D E F G H J K M 2. Reduce cutting speed
A L
1-1/2 2-11/16 1-3/16 0.515 1.406 1-1/2 0.515 1.371 9/16 1.302 0.377 7/16 •Chipping at center part or overall 1. Carry out honing. Or enlarge.
2 3-1/4 1-23/32 0.700 1.900 1-3/4 0.700 1.809 5/8 1.772 0.440 1/2 2. Change number of rotation(in case machine vibrates)
2-1/2 3-1/2 1-15/16 0.700 2.400 2 0.700 2.312 3/4 2.245 0.503 9/16 3. Increase cutting speed
4. In ease of squeaking noise during cutting, increase feed.
Fracture of 5. It dry cutting use cutting fluid or blow air.
cutting edge 6. Replace chuck or collet
7. Reduce cutting speed
15 Tolerances
•Large fracturing of cutting edge 1. Decrease feed rate
2. If 4 flute reduce to 2 flute
Element Direction Tolerance
3. Carry out honing. Or enlarge
Diameter of Shank, A minus .0001 to .0005 4. Replace chuck or collet
Length of Shank, L plus or minus 1/32 5. Reduce cutting speed
Dimension, B plus or minus 1/64 6. If dry cutting, change to wet cutting. In case oil supply in wet
Dimension, C plus .002 cutting is from the front, change to rear at an angle or from
Dimension, D minus 1/64 side top. Use ample supply.
Dimension, E plus or minus 1/64
Dimension, F plus or minus .005 1. Reduce cutting speed
Dimension, G minus 1/64 Rapid tool wear 2. Up cut → Down cut
3. Increase feed
Dimension, H plus 1/64 4. Utilize wet cutting or air
Dimension, J plus or minus .002 5. If reground tool, improve surface roughness of flank.
Dimension, K plus .003
Extracted from Milling Cutters and End Mills. MCTI 1989.









1302 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1303

TECHNICAL
DATA SUPER CUTTING END MILLS



ROTARY
ROTARY



Trouble Occurrences of trouble Countermeasures

•Surface is good but rough 1. Decrease feed
2. In case using 2 flute, increase to 4 flute

•Small chip welding 1. Increase cutting speed TOOL HOLDERS
2. Utilize wet cutting air blow(ample supply) TOOL HOLDERS
3. Carry out fine honing
4. Up cut → Down cut
Inferior finished surface 5. Increase feed or enlarge finish allowance
•With transverse streaks 1. Carry out fine honing
2. Use water insoluble cutting fluid
3. Down cut → Up cut
HYDRAULIC CHUCK - CAT, BT TG COLLET CHUCK - CAT, BT
•Signs of excessive cutting 1. Reduce finishing depth of cut
2. Increase cutting speed DUAL CONTACT HYDRAULIC CHUCK - CCT, CBT, HSK MILLING CHUCK - CAT, BT
3. Reduce feed
HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE) DUAL CONTACT HIGH SPEED MILLING CHUCK - CCT, CBT, HSK
•Finish dimensions are 1. Up cut → Down cut SHRINK FIT HOLDER - CAT, BT MILLING CHUCK COLLET
on minus side 2. Reduce finishing depth of cut
3. Replace chuck or collet DUAL CONTACT SHRINK FIT HOLDER - CCT, CBT, HSK MORSE TAPER ADAPTER - CAT, BT
4. Reduce projection amount
5. Increase cutting speed SHRINK FIT EXTENSION - ST TAPPING CHUCK - CAT, BT
Poor machining END MILL HOLDER & SIDE LOCK ARBOR - CAT, BT SYNCHRO TAPPING ER CHUCK - CAT
accuracy •Poor perpendicularity 1. Reduce finishing depth of cut
2. Replace chuck or collet
3. Reduce projection amount DUAL CONTACT SIDE LOCK ARBOR - CCT, CBT QUICK CHANGE TAP ADAPTER
4. Increase cutting speed DUAL CONTACT END MILL HOLDER - HSK SHELL MILL ARBOR - CAT, BT
5. 2Flute → 4 Flute
6. Reduce feed ER COLLET CHUCK - CAT, BT DUAL CONTACT SHELL MILL ARBOR - CCT, CBT
7. Check wear rate → Replace tool
DUAL CONTACT ER COLLET CHUCK - HSK NC DRILL CHUCK - CAT, BT
1. Increase feed rate(in case over 0.05 mm/Zahn, try reducing)
2. Change cutting speed SHORT & TENSION ER COLLET CHUCK - SHORT, DUAL CONTACT NC DRILL CHUCK - HSK
Chattering 3. Replace chuck or collet
4. Reduce projection amount TENSION (For TAPPING) STRAIGHT NC DRILL CHUCK - K
5. Use 2 flute cutter for rough cutting and 4 flute for finishing NC ER COLLET CHUCK - NC (For CNC LATHE) JACOBS TAPER ARBOR - CAT, BT
6. Down cut → Up cut
ER COLLET STUB ARBOR - CAT, BT

DUAL CONTACT SK SLIM CHUCK - CCT, CBT, HSK SLITTING SAW ARBOR - CAT, BT
STRAIGHT SK SLIM CHUCK - K PULL STUD

SK COLLET TOOL CLAMP
COOLANT TUBE














1304 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com

TECHNICAL
DATA SUPER CUTTING END MILLS



ROTARY
ROTARY



Trouble Occurrences of trouble Countermeasures

•Surface is good but rough 1. Decrease feed
2. In case using 2 flute, increase to 4 flute

•Small chip welding 1. Increase cutting speed TOOL HOLDERS
2. Utilize wet cutting air blow(ample supply) TOOL HOLDERS
3. Carry out fine honing
4. Up cut → Down cut
Inferior finished surface 5. Increase feed or enlarge finish allowance
•With transverse streaks 1. Carry out fine honing
2. Use water insoluble cutting fluid
3. Down cut → Up cut
HYDRAULIC CHUCK - CAT, BT TG COLLET CHUCK - CAT, BT
•Signs of excessive cutting 1. Reduce finishing depth of cut
2. Increase cutting speed DUAL CONTACT HYDRAULIC CHUCK - CCT, CBT, HSK MILLING CHUCK - CAT, BT
3. Reduce feed
HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE) DUAL CONTACT HIGH SPEED MILLING CHUCK - CCT, CBT, HSK
•Finish dimensions are 1. Up cut → Down cut SHRINK FIT HOLDER - CAT, BT MILLING CHUCK COLLET
on minus side 2. Reduce finishing depth of cut
3. Replace chuck or collet DUAL CONTACT SHRINK FIT HOLDER - CCT, CBT, HSK MORSE TAPER ADAPTER - CAT, BT
4. Reduce projection amount
5. Increase cutting speed SHRINK FIT EXTENSION - ST TAPPING CHUCK - CAT, BT
Poor machining END MILL HOLDER & SIDE LOCK ARBOR - CAT, BT SYNCHRO TAPPING ER CHUCK - CAT
accuracy •Poor perpendicularity 1. Reduce finishing depth of cut
2. Replace chuck or collet
3. Reduce projection amount DUAL CONTACT SIDE LOCK ARBOR - CCT, CBT QUICK CHANGE TAP ADAPTER
4. Increase cutting speed DUAL CONTACT END MILL HOLDER - HSK SHELL MILL ARBOR - CAT, BT
5. 2Flute → 4 Flute
6. Reduce feed ER COLLET CHUCK - CAT, BT DUAL CONTACT SHELL MILL ARBOR - CCT, CBT
7. Check wear rate → Replace tool
DUAL CONTACT ER COLLET CHUCK - HSK NC DRILL CHUCK - CAT, BT
1. Increase feed rate(in case over 0.05 mm/Zahn, try reducing)
2. Change cutting speed SHORT & TENSION ER COLLET CHUCK - SHORT, DUAL CONTACT NC DRILL CHUCK - HSK
Chattering 3. Replace chuck or collet
4. Reduce projection amount TENSION (For TAPPING) STRAIGHT NC DRILL CHUCK - K
5. Use 2 flute cutter for rough cutting and 4 flute for finishing NC ER COLLET CHUCK - NC (For CNC LATHE) JACOBS TAPER ARBOR - CAT, BT
6. Down cut → Up cut
ER COLLET STUB ARBOR - CAT, BT

DUAL CONTACT SK SLIM CHUCK - CCT, CBT, HSK SLITTING SAW ARBOR - CAT, BT
STRAIGHT SK SLIM CHUCK - K PULL STUD

SK COLLET TOOL CLAMP
COOLANT TUBE














1304 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com

SELECTION GUIDE




MODEL DESCRIPTION PAGE MODEL DESCRIPTION PAGE
HYDRAULIC CHUCK POWER MILLING CHUCK
• CAT 1308 • CAT 1396
• BT 1314 • BT 1396
DUAL CONTACT HYDRAULIC CHUCK DUAL CONTACT HIGH SPEED POWER MILLING CHUCK
• CCT 1320 • CCT 1397
• CBT 1323 • CBT 1398
• HSK 1326 • HSK 1399
HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE) 1331 ACCESSORY & PART 1400
SHRINK FIT HOLDER MORSE TAPER ADAPTER
• CAT 1339 MORSE TAPER
• BT 1341 ADAPTER • CAT 1401
DUAL CONTACT SHRINK FIT HOLDER • BT 1401
• CCT 1343 TAPPING CHUCK
• CBT 1345 • CAT 1402
• HSK 1347 • BT 1403
SHRINK FIT EXTENSION SYNCHRO TAPPING ER CHUCK
• ST 1349 • CAT 1404
END MILL HOLDER ACCESSORY & PART 1405
• CAT 1352 SHELL MILL ARBOR
• BT 1358 • CAT 1406
DUAL CONTACT SIDE LOCK ARBOR • BT 1407
• CCT 1363 DUAL CONTACT SHELL MILL ARBOR
• CBT 1364 • CCT 1408
DUAL CONTACT END MILL HOLDER • CBT 1409
• HSK (COOLANT CHANNEL TYPE) 1365 ACCESSORY & PART 1410
ER COLLET CHUCK NC DRILL CHUCK
• CAT 1366 • CAT 1411
• BT 1368
DUAL CONTACT ER COLLET CHUCK • BT 1412
• HSK 1371 DUAL CONTACT NC DRILL CHUCK
ER COLLET CHUCK • HSK 1413
• SHORT 1372 STRAIGHT NC DRILL CHUCK
• TENSION (For TAPPING) 1372 • STRAIGHT-K 1413
NC ER COLLET CHUCK JACOBS TAPER JACOBS TAPER ARBOR
• NC (For CNC LATHE) 1373 ARBOR • CAT 1414
ACCESSORY & PART 1374 • BT 1414
DUAL CONTACT SK SLIM CHUCK STUB ARBOR
• CAT 1384 STUB ARBOR • CAT 1415
• CCT 1385 • BT 1415
• CBT 1386 SLITTING SAW SLITTING SAW ARBOR
• HSK 1387 • CAT 1417
STRAIGHT SK SLIM CHUCK ARBOR • BT 1417
• STRAIGHT-K 1388 PULL STUD 1418
ACCESSORY & PART 1389 PULL STUD & TOOL
TG COLLET CHUCK CLAMP TOOL CLAMP 1419
COOLANT TUBE
1419
TG COLLET CHUCK • CAT 1393
1394
• BT
ACCESSORY & PART 1395 TECHNICAL INFORMATION 1420

1306 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1307

SELECTION GUIDE




MODEL DESCRIPTION PAGE MODEL DESCRIPTION PAGE
HYDRAULIC CHUCK POWER MILLING CHUCK
• CAT 1308 • CAT 1396
• BT 1314 • BT 1396
DUAL CONTACT HYDRAULIC CHUCK DUAL CONTACT HIGH SPEED POWER MILLING CHUCK
• CCT 1320 • CCT 1397
• CBT 1323 • CBT 1398
• HSK 1326 • HSK 1399
HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE) 1331 ACCESSORY & PART 1400
SHRINK FIT HOLDER MORSE TAPER ADAPTER
• CAT 1339 MORSE TAPER
• BT 1341 ADAPTER • CAT 1401
DUAL CONTACT SHRINK FIT HOLDER • BT 1401
• CCT 1343 TAPPING CHUCK
• CBT 1345 • CAT 1402
• HSK 1347 • BT 1403
SHRINK FIT EXTENSION SYNCHRO TAPPING ER CHUCK
• ST 1349 • CAT 1404
END MILL HOLDER ACCESSORY & PART 1405
• CAT 1352 SHELL MILL ARBOR
• BT 1358 • CAT 1406
DUAL CONTACT SIDE LOCK ARBOR • BT 1407
• CCT 1363 DUAL CONTACT SHELL MILL ARBOR
• CBT 1364 • CCT 1408
DUAL CONTACT END MILL HOLDER • CBT 1409
• HSK (COOLANT CHANNEL TYPE) 1365 ACCESSORY & PART 1410
ER COLLET CHUCK NC DRILL CHUCK
• CAT 1366 • CAT 1411
• BT 1368
DUAL CONTACT ER COLLET CHUCK • BT 1412
• HSK 1371 DUAL CONTACT NC DRILL CHUCK
ER COLLET CHUCK • HSK 1413
• SHORT 1372 STRAIGHT NC DRILL CHUCK
• TENSION (For TAPPING) 1372 • STRAIGHT-K 1413
NC ER COLLET CHUCK JACOBS TAPER JACOBS TAPER ARBOR
• NC (For CNC LATHE) 1373 ARBOR • CAT 1414
ACCESSORY & PART 1374 • BT 1414
DUAL CONTACT SK SLIM CHUCK STUB ARBOR
• CAT 1384 STUB ARBOR • CAT 1415
• CCT 1385 • BT 1415
• CBT 1386 SLITTING SAW SLITTING SAW ARBOR
• HSK 1387 • CAT 1417
STRAIGHT SK SLIM CHUCK ARBOR • BT 1417
• STRAIGHT-K 1388 PULL STUD 1418
ACCESSORY & PART 1389 PULL STUD & TOOL
TG COLLET CHUCK CLAMP TOOL CLAMP 1419
COOLANT TUBE
1419
TG COLLET CHUCK • CAT 1393
1394
• BT
ACCESSORY & PART 1395 TECHNICAL INFORMATION 1420

1306 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1307

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CAT CAT
HYDRAULIC CHUCK (SLIM) HYDRAULIC CHUCK (SLIM)


G L2
FIG.1 G L2



d1 D1 D2
d1 D1 D2
TAPER No.
L1
L TAPER No.
L1
L
FIG.2
G L2
Taper G Value RPM Run-Out Coolant
ASME B5.50 Accuracy (at 3D) System
- CAT
d1 D1 D2 D3 AT3 2.5 25,000 ≤0.00012" AD/B
ASME B5.50-2009-CAT Unit : mm
L1 EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
TAPER No.
L
WK060 CAT40 AD/B - HC 6 - 80.5 6 26 49.5 80.5 29.5 27 M5x0.8
Taper G Value RPM Run-Out Coolant WK062 CAT40 AD/B - HC 6 - 110 6 26 49.5 110 29.5 27 M5x0.8
ASME B5.50 Accuracy (at 3D) System
- CAT WK064 CAT40 AD/B - HC 8 - 80.5 8 28 49.5 80.5 30 27 M6x1.0
AT3 2.5 25,000 ≤0.00012" AD/B
WK066 CAT40 AD/B - HC 8 - 110 8 28 49.5 110 30 27 M6x1.0
ASME B5.50-2009-CAT WK068 CAT40 AD/B - HC 10 - 80.5 10 30 49.5 80.5 31 32 M8x1.0
Unit : inch
WK070 CAT40 AD/B - HC 10 - 110 10 30 49.5 110 31 32 M8x1.0
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L1 L2 G Remarks WK072 CAT40 AD/B - HC 12 - 80.5 12 32 49.5 80.5 31.5 37 M10x1.0
WK074 40 CAT40 AD/B - HC 12 - 110 12 32 49.5 110 31.5 37 M10x1.0
WK020 CAT40 AD/B - HC 1/4 - 4.00 0.250 1.024 1.750 - 4.000 1.280 1.063 M5x0.8mm
WK022 CAT40 AD/B - HC 3/8 - 4.00 0.375 1.181 1.750 - 4.000 1.634 1.260 M6x1.0mm WK076 CAT40 AD/B - HC 16 - 80.5 16 38 49.5 80.5 33 42 M12x1.0
WK024 CAT40 AD/B - HC 1/2 - 4.00 0.500 1.260 1.750 - 4.000 1.634 1.457 M10x1.0mm WK078 CAT40 AD/B - HC 16 - 110 16 38 49.5 110 33 42 M12x1.0
WK026 40 CAT40 AD/B - HC 5/8 - 4.00 0.625 1.496 1.750 - 4.000 1.949 1.654 M10x1.0mm FIG.1 WK080 CAT40 AD/B - HC 20 - 80.5 20 42 49.5 80.5 34 42 M16x1.0
WK028 CAT40 AD/B - HC 3/4 - 4.00 0.750 1.654 1.750 - 4.000 1.949 1.654 M10x1.0mm WK082 CAT40 AD/B - HC 20 - 110 20 42 49.5 110 34 42 M16x1.0
WK030 CAT40 AD/B - HC 1 - 4.00 1.000 2.165 2.480 - 4.000 2.618 1.890 M16x1.0mm WK084 CAT40 AD/B - HC 25 - 80.5 25 55 66 80.5 22 48 M16x1.
WK032 CAT40 AD/B - HC 1 1/4 - 4.00 1.250 2.480 3.150 - 4.000 1.378 2.165 M16x1.0mm WK086 CAT40 AD/B - HC 32 - 80.5 32 63 80 80.5 25.5 55 M16x1.0
WL020 CAT50 AD/B - HC 1/4 - 4.00 0.250 1.024 1.978 2.752 4.000 1.280 1.063 M5x0.8mm WL060 CAT50 AD/B - HC 6 - 80.5 6 26 49.5 80.5 30 27 M5x0.8
WL022 CAT50 AD/B - HC 3/8 - 4.00 0.375 1.181 1.978 2.752 4.000 1.417 1.260 M6x1.0mm WL062 CAT50 AD/B - HC 8 - 80.5 8 28 49.5 80.5 30 27 M6x1.0
WL024 CAT50 AD/B - HC 1/2 - 4.00 0.500 1.260 1.978 2.752 4.000 1.634 1.457 M10x1.0mm WL064 50 CAT50 AD/B - HC 10 - 80.5 10 30 49.5 80.5 32 32 M8x1.0
WL026 50 CAT50 AD/B - HC 5/8 - 4.00 0.625 1.496 1.978 2.752 4.000 1.870 1.654 M10x1.0mm FIG.2 WL066 CAT50 AD/B - HC 12 - 80.5 12 32 49.5 80.5 35 37 M10x1.0
WL028 CAT50 AD/B - HC 3/4 - 4.00 0.750 1.654 1.978 2.752 4.000 1.949 1.654 M10x1.0mm WL068 CAT50 AD/B - HC 16 - 80.5 16 38 49.5 80.5 40 42 M12x1.0
WL030 CAT50 AD/B - HC 1 - 4.00 1.000 2.244 2.480 2.752 4.000 1.949 1.890 M16x1.0mm WL070 CAT50 AD/B - HC 20 - 80.5 20 42 49.5 80.5 40 42 M16x1.0
WL032 CAT50 AD/B - HC 1 1/4 - 4.00 1.250 2.520 - 2.752 4.000 2.559 2.165 M16x1.0mm * Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.

* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.

















1308 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1309

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CAT CAT
HYDRAULIC CHUCK (SLIM) HYDRAULIC CHUCK (SLIM)


G L2
FIG.1 G L2



d1 D1 D2
d1 D1 D2
TAPER No.
L1
L TAPER No.
L1
L
FIG.2
G L2
Taper G Value RPM Run-Out Coolant
ASME B5.50 Accuracy (at 3D) System
- CAT
d1 D1 D2 D3 AT3 2.5 25,000 ≤0.00012" AD/B
ASME B5.50-2009-CAT Unit : mm
L1 EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
TAPER No.
L
WK060 CAT40 AD/B - HC 6 - 80.5 6 26 49.5 80.5 29.5 27 M5x0.8
Taper G Value RPM Run-Out Coolant WK062 CAT40 AD/B - HC 6 - 110 6 26 49.5 110 29.5 27 M5x0.8
ASME B5.50 Accuracy (at 3D) System
- CAT WK064 CAT40 AD/B - HC 8 - 80.5 8 28 49.5 80.5 30 27 M6x1.0
AT3 2.5 25,000 ≤0.00012" AD/B
WK066 CAT40 AD/B - HC 8 - 110 8 28 49.5 110 30 27 M6x1.0
ASME B5.50-2009-CAT WK068 CAT40 AD/B - HC 10 - 80.5 10 30 49.5 80.5 31 32 M8x1.0
Unit : inch
WK070 CAT40 AD/B - HC 10 - 110 10 30 49.5 110 31 32 M8x1.0
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L1 L2 G Remarks WK072 CAT40 AD/B - HC 12 - 80.5 12 32 49.5 80.5 31.5 37 M10x1.0
WK074 40 CAT40 AD/B - HC 12 - 110 12 32 49.5 110 31.5 37 M10x1.0
WK020 CAT40 AD/B - HC 1/4 - 4.00 0.250 1.024 1.750 - 4.000 1.280 1.063 M5x0.8mm
WK022 CAT40 AD/B - HC 3/8 - 4.00 0.375 1.181 1.750 - 4.000 1.634 1.260 M6x1.0mm WK076 CAT40 AD/B - HC 16 - 80.5 16 38 49.5 80.5 33 42 M12x1.0
WK024 CAT40 AD/B - HC 1/2 - 4.00 0.500 1.260 1.750 - 4.000 1.634 1.457 M10x1.0mm WK078 CAT40 AD/B - HC 16 - 110 16 38 49.5 110 33 42 M12x1.0
WK026 40 CAT40 AD/B - HC 5/8 - 4.00 0.625 1.496 1.750 - 4.000 1.949 1.654 M10x1.0mm FIG.1 WK080 CAT40 AD/B - HC 20 - 80.5 20 42 49.5 80.5 34 42 M16x1.0
WK028 CAT40 AD/B - HC 3/4 - 4.00 0.750 1.654 1.750 - 4.000 1.949 1.654 M10x1.0mm WK082 CAT40 AD/B - HC 20 - 110 20 42 49.5 110 34 42 M16x1.0
WK030 CAT40 AD/B - HC 1 - 4.00 1.000 2.165 2.480 - 4.000 2.618 1.890 M16x1.0mm WK084 CAT40 AD/B - HC 25 - 80.5 25 55 66 80.5 22 48 M16x1.
WK032 CAT40 AD/B - HC 1 1/4 - 4.00 1.250 2.480 3.150 - 4.000 1.378 2.165 M16x1.0mm WK086 CAT40 AD/B - HC 32 - 80.5 32 63 80 80.5 25.5 55 M16x1.0
WL020 CAT50 AD/B - HC 1/4 - 4.00 0.250 1.024 1.978 2.752 4.000 1.280 1.063 M5x0.8mm WL060 CAT50 AD/B - HC 6 - 80.5 6 26 49.5 80.5 30 27 M5x0.8
WL022 CAT50 AD/B - HC 3/8 - 4.00 0.375 1.181 1.978 2.752 4.000 1.417 1.260 M6x1.0mm WL062 CAT50 AD/B - HC 8 - 80.5 8 28 49.5 80.5 30 27 M6x1.0
WL024 CAT50 AD/B - HC 1/2 - 4.00 0.500 1.260 1.978 2.752 4.000 1.634 1.457 M10x1.0mm WL064 50 CAT50 AD/B - HC 10 - 80.5 10 30 49.5 80.5 32 32 M8x1.0
WL026 50 CAT50 AD/B - HC 5/8 - 4.00 0.625 1.496 1.978 2.752 4.000 1.870 1.654 M10x1.0mm FIG.2 WL066 CAT50 AD/B - HC 12 - 80.5 12 32 49.5 80.5 35 37 M10x1.0
WL028 CAT50 AD/B - HC 3/4 - 4.00 0.750 1.654 1.978 2.752 4.000 1.949 1.654 M10x1.0mm WL068 CAT50 AD/B - HC 16 - 80.5 16 38 49.5 80.5 40 42 M12x1.0
WL030 CAT50 AD/B - HC 1 - 4.00 1.000 2.244 2.480 2.752 4.000 1.949 1.890 M16x1.0mm WL070 CAT50 AD/B - HC 20 - 80.5 20 42 49.5 80.5 40 42 M16x1.0
WL032 CAT50 AD/B - HC 1 1/4 - 4.00 1.250 2.520 - 2.752 4.000 2.559 2.165 M16x1.0mm * Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.

* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.

















1308 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1309

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CAT CAT
HYDRAULIC CHUCK (Power E Hydro) HYDRAULIC CHUCK (Short & Rigid)


G L2 G L2





d1 D1 D2 d1 D1 D2




TAPER No. L TAPER No. L


Taper Run-Out Coolant Taper Run-Out Coolant
ASME B5.50 Accuracy G Value RPM (at 3D) System ASME B5.50 Accuracy G Value RPM (at 3D) System
- CAT AT3 2.5 25,000 ≤0.00012" AD/B - CAT AT3 2.5 25,000 ≤0.00012" AD/B

ASME B5.50-2009-CAT Unit : inch ASME B5.50-2009-CAT Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
WK022PE CAT40 AD/B - HC 3/4P - 2.539 0.75 1.496 1.938 2.539 1.889 M8x1.0mm WK020SNR CAT40 AD/B - HC 1/2S - 2.52 0.500 1.260 1.654 2.520 1.457 M8x1.0mm
WK023PE 40 CAT40 AD/B - HC 3/4P - 4.000 0.75 1.496 1.938 4.000 1.889 M8x1.0mm WK021SNR CAT40 AD/B - HC 5/8S - 2.52 0.625 1.362 1.752 2.520 1.654 M10x1.0mm
WL028PE CAT50 AD/B - HC 1 1/4P - 3.188 1.25 2.303 2.834 3.188 2.244 M8x1.0mm WK022SNR 40 CAT40 AD/B - HC 3/4S - 2.52 0.750 1.469 1.949 2.520 1.654 M10x1.0mm
WL030PE 50 CAT50 AD/B - HC 1 1/4P - 6.000 1.25 2.303 2.834 6.000 2.244 M8x1.0mm WK024SNR CAT40 AD/B - HC 1S - 3.50 1.000 2.244 2.598 3.500 1.890 M16x1.0mm
WL020SNR CAT50 AD/B - HC 1/2S - 3.19 0.500 1.879 2.752 3.189 1.457 M8x1.0mm
WL022SNR CAT50 AD/B - HC 5/8S - 3.19 0.625 1.819 2.752 3.189 1.654 M8x1.0mm
Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G WL024SNR 50 CAT50 AD/B - HC 3/4S - 3.19 0.75 2.185 2.752 3.189 1.654 M10x1.0mm
WL026SNR CAT50 AD/B - HC 1.00S - 3.19 1.000 2.185 2.752 3.189 1.890 M16x1.0mm
WK102PE 40 CAT40 AD/B - HC 20P - 64.5 20 38 49.25 64.5 48 M8x1.0 WL028SNR CAT50 AD/B - HC 1.25S - 3.19 1.250 2.185 2.752 3.189 2.165 M16x1.0mm
WK103PE CAT40 AD/B - HC 20P - 101.6 20 38 49.25 101.6 48 M8x1.0
WL104PE 50 CAT50 AD/B - HC 32P - 81 32 58.5 72 81 57 M8x1.0 Unit : mm
WL106PE CAT50 AD/B - HC 32P - 152.4 32 58.5 72 152.4 57 M8x1.0 EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G

* High Clamping Torque Power version WK100SNR 40 CAT40 AD/B - HC 12S - 50 12 32 42 50 37 M8x1.0
(Please refer to page 1420, Technical Information) WK102SNR CAT40 AD/B - HC 20S - 64.5 20 37 49.5 64.5 42 M16x1.0
* Applicable for milling(roughing and finishing)
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WL100SNR CAT50 AD/B - HC 12S - 50 12 32 42 50 37 M8x1.0
WL102SNR 50 CAT50 AD/B - HC 20S - 64.5 20 37 49.5 64.5 42 M16x1.0
WL104SNR CAT50 AD/B - HC 32S - 81 32 55 72 81 55 M16x1.0

* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.





















1310 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1311

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CAT CAT
HYDRAULIC CHUCK (Power E Hydro) HYDRAULIC CHUCK (Short & Rigid)


G L2 G L2





d1 D1 D2 d1 D1 D2




TAPER No. L TAPER No. L


Taper Run-Out Coolant Taper Run-Out Coolant
ASME B5.50 Accuracy G Value RPM (at 3D) System ASME B5.50 Accuracy G Value RPM (at 3D) System
- CAT AT3 2.5 25,000 ≤0.00012" AD/B - CAT AT3 2.5 25,000 ≤0.00012" AD/B

ASME B5.50-2009-CAT Unit : inch ASME B5.50-2009-CAT Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
WK022PE CAT40 AD/B - HC 3/4P - 2.539 0.75 1.496 1.938 2.539 1.889 M8x1.0mm WK020SNR CAT40 AD/B - HC 1/2S - 2.52 0.500 1.260 1.654 2.520 1.457 M8x1.0mm
WK023PE 40 CAT40 AD/B - HC 3/4P - 4.000 0.75 1.496 1.938 4.000 1.889 M8x1.0mm WK021SNR CAT40 AD/B - HC 5/8S - 2.52 0.625 1.362 1.752 2.520 1.654 M10x1.0mm
WL028PE CAT50 AD/B - HC 1 1/4P - 3.188 1.25 2.303 2.834 3.188 2.244 M8x1.0mm WK022SNR 40 CAT40 AD/B - HC 3/4S - 2.52 0.750 1.469 1.949 2.520 1.654 M10x1.0mm
WL030PE 50 CAT50 AD/B - HC 1 1/4P - 6.000 1.25 2.303 2.834 6.000 2.244 M8x1.0mm WK024SNR CAT40 AD/B - HC 1S - 3.50 1.000 2.244 2.598 3.500 1.890 M16x1.0mm
WL020SNR CAT50 AD/B - HC 1/2S - 3.19 0.500 1.879 2.752 3.189 1.457 M8x1.0mm
WL022SNR CAT50 AD/B - HC 5/8S - 3.19 0.625 1.819 2.752 3.189 1.654 M8x1.0mm
Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G WL024SNR 50 CAT50 AD/B - HC 3/4S - 3.19 0.75 2.185 2.752 3.189 1.654 M10x1.0mm
WL026SNR CAT50 AD/B - HC 1.00S - 3.19 1.000 2.185 2.752 3.189 1.890 M16x1.0mm
WK102PE 40 CAT40 AD/B - HC 20P - 64.5 20 38 49.25 64.5 48 M8x1.0 WL028SNR CAT50 AD/B - HC 1.25S - 3.19 1.250 2.185 2.752 3.189 2.165 M16x1.0mm
WK103PE CAT40 AD/B - HC 20P - 101.6 20 38 49.25 101.6 48 M8x1.0
WL104PE 50 CAT50 AD/B - HC 32P - 81 32 58.5 72 81 57 M8x1.0 Unit : mm
WL106PE CAT50 AD/B - HC 32P - 152.4 32 58.5 72 152.4 57 M8x1.0 EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G

* High Clamping Torque Power version WK100SNR 40 CAT40 AD/B - HC 12S - 50 12 32 42 50 37 M8x1.0
(Please refer to page 1420, Technical Information) WK102SNR CAT40 AD/B - HC 20S - 64.5 20 37 49.5 64.5 42 M16x1.0
* Applicable for milling(roughing and finishing)
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WL100SNR CAT50 AD/B - HC 12S - 50 12 32 42 50 37 M8x1.0
WL102SNR 50 CAT50 AD/B - HC 20S - 64.5 20 37 49.5 64.5 42 M16x1.0
WL104SNR CAT50 AD/B - HC 32S - 81 32 55 72 81 55 M16x1.0

* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.





















1310 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1311

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CAT CAT
HYDRAULIC CHUCK (RADIAL TOOL LENGTH PRE-SETTING TYPE) HYDRAULIC CHUCK (For MOULD)


Radial Length
Adjustment
L2 L2
B G
3°
d1 D1 D2
AD d1 D1 D2
L1
L
L1
B
TAPER No. L

Taper Run-Out Coolant
Taper Run-Out Coolant ASME B5.50 Accuracy G Value RPM (at 3D) System
ASME B5.50 Accuracy G Value RPM (at 3D) System - CAT
- CAT AT3 2.5 25,000 ≤0.00012" AD/B AT3 2.5 25,000 ≤0.00012" AD/B
ASME B5.50-2009-CAT Unit : mm ASME B5.50-2009-CAT Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2
WK020HMC CAT40 AD/B - HMC 1/4 - 4.72 0.250 0.787 1.949 4.724 2.756 1.063 M5x0.8mm
WK100HCR CAT40 AD/B - HCR 12 - 80.5 12 32 49.5 80.5 31.5 37 WK022HMC CAT40 AD/B - HMC 1/4 - 5.91 0.250 0.787 1.949 5.906 3.937 1.063 M5x0.8mm
WK102HCR 40 CAT40 AD/B - HCR 20 - 80.5 20 42 49.5 80.5 34 42 WK024HMC CAT40 AD/B - HMC 5/16 - 4.72 0.313 0.866 1.949 4.724 2.756 1.063 M6x1.0mm
WK104HCR CAT40 AD/B - HCR 32 - 110 32 64 80 110 50 55 WK026HMC CAT40 AD/B - HMC 5/16 - 5.91 0.313 0.866 1.949 5.906 3.937 1.063 M6x1.0mm
WL100HCR CAT50 AD/B - HCR 12 - 80.5 12 32 49.5 80.5 31.5 37 WK028HMC CAT40 AD/B - HMC 3/8 - 4.72 0.375 0.945 1.949 4.724 2.756 1.260 M8x1.0mm
WL102HCR 50 CAT50 AD/B - HCR 20 - 80.5 20 42 49.5 80.5 34 42 WK030HMC 40 CAT40 AD/B - HMC 3/8 - 5.91 0.375 0.945 1.949 5.906 3.937 1.260 M8x1.0mm
WL104HCR CAT50 AD/B - HCR 32 - 100 32 60 60 100 - 55 WK032HMC CAT40 AD/B - HMC 1/2 - 4.72 0.500 1.024 1.949 4.724 2.756 1.457 M10x1.0mm
WK034HMC CAT40 AD/B - HMC 1/2 - 5.91 0.500 1.024 1.949 5.906 3.937 1.457 M10x1.0mm
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WK036HMC CAT40 AD/B - HMC 5/8 - 4.72 0.625 1.260 1.949 4.724 2.756 1.654 M12x1.0mm
WK038HMC CAT40 AD/B - HMC 5/8 - 5.91 0.625 1.260 1.949 5.906 3.937 1.654 M12x1.0mm
WK040HMC CAT40 AD/B - HMC 3/4 - 4.72 0.750 1.339 1.949 4.724 2.756 1.654 M16x1.0mm
WK042HMC CAT40 AD/B - HMC 3/4 - 5.91 0.750 1.339 1.949 5.906 3.937 1.654 M16x1.0mm
WL020HMC CAT50 AD/B - HMC 1/4 - 5.91 0.250 0.787 1.752 5.906 3.937 1.063 M5x0.8mm
WL022HMC CAT50 AD/B - HMC 5/16 - 5.91 0.313 0.866 1.752 5.906 3.937 1.063 M6x1.0mm
WL024HMC 50 CAT50 AD/B - HMC 3/8 - 5.91 0.375 0.945 1.752 5.906 3.937 1.260 M8x1.0mm
WL026HMC CAT50 AD/B - HMC 1/2 - 5.91 0.500 1.024 1.752 5.906 3.937 1.457 M10x1.0mm
WL028HMC CAT50 AD/B - HMC 5/8 - 5.91 0.625 1.260 1.752 5.906 3.937 1.654 M12x1.0mm
WL030HMC CAT50 AD/B - HMC 3/4 - 5.91 0.750 1.339 1.752 5.906 3.937 1.654 M16x1.0mm
Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
WK100HMC CAT40 AD/B - HMC 6 - 120 6 20 49.5 120 70 27 M5X0.8
WK102HMC CAT40 AD/B - HMC 6 - 150 6 20 49.5 150 100 27 M5X0.8
WK104HMC CAT40 AD/B - HMC 8 - 120 8 22 49.5 120 70 27 M6X1.0
WK106HMC CAT40 AD/B - HMC 8 - 150 8 22 49.5 150 100 27 M6X1.0
WK108HMC CAT40 AD/B - HMC 10 - 120 10 24 49.5 120 70 32 M8X1.0
WK110HMC CAT40 AD/B - HMC 10 - 150 10 24 49.5 150 100 32 M8X1.0
WK112HMC 40 CAT40 AD/B - HMC 12 - 120 12 25 49.5 120 70 37 M10X1.0
WK114HMC CAT40 AD/B - HMC 12 - 150 12 25 49.5 150 100 37 M10X1.0
WK116HMC CAT40 AD/B - HMC 16 - 120 16 32 49.5 120 70 42 M12X1.0
WK118HMC CAT40 AD/B - HMC 16 - 150 16 32 49.5 150 100 42 M12X1.0
WK120HMC CAT40 AD/B - HMC 20 - 120 20 34 49.5 120 70 42 M16X1.0
WK122HMC CAT40 AD/B - HMC 20 - 150 20 34 49.5 150 100 42 M16X1.0
WL100HMC CAT50 AD/B - HMC 6 - 150 6 20 44.5 150 100 27 M5X0.8
WL102HMC CAT50 AD/B - HMC 8 - 150 8 22 44.5 150 100 27 M6X1.0
WL104HMC 50 CAT50 AD/B - HMC 10 - 150 10 24 44.5 150 100 32 M8X1.0
WL106HMC CAT50 AD/B - HMC 12 - 150 12 25 44.5 150 100 37 M10X1.0
WL108HMC CAT50 AD/B - HMC 16 - 150 16 32 44.5 150 100 42 M12X1.0
WL110HMC CAT50 AD/B - HMC 20 - 150 20 34 44.5 150 100 42 M16X1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
1312 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1313

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CAT CAT
HYDRAULIC CHUCK (RADIAL TOOL LENGTH PRE-SETTING TYPE) HYDRAULIC CHUCK (For MOULD)


Radial Length
Adjustment
L2 L2
B G
3°
d1 D1 D2
AD d1 D1 D2
L1
L
L1
B
TAPER No. L

Taper Run-Out Coolant
Taper Run-Out Coolant ASME B5.50 Accuracy G Value RPM (at 3D) System
ASME B5.50 Accuracy G Value RPM (at 3D) System - CAT
- CAT AT3 2.5 25,000 ≤0.00012" AD/B AT3 2.5 25,000 ≤0.00012" AD/B
ASME B5.50-2009-CAT Unit : mm ASME B5.50-2009-CAT Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2
WK020HMC CAT40 AD/B - HMC 1/4 - 4.72 0.250 0.787 1.949 4.724 2.756 1.063 M5x0.8mm
WK100HCR CAT40 AD/B - HCR 12 - 80.5 12 32 49.5 80.5 31.5 37 WK022HMC CAT40 AD/B - HMC 1/4 - 5.91 0.250 0.787 1.949 5.906 3.937 1.063 M5x0.8mm
WK102HCR 40 CAT40 AD/B - HCR 20 - 80.5 20 42 49.5 80.5 34 42 WK024HMC CAT40 AD/B - HMC 5/16 - 4.72 0.313 0.866 1.949 4.724 2.756 1.063 M6x1.0mm
WK104HCR CAT40 AD/B - HCR 32 - 110 32 64 80 110 50 55 WK026HMC CAT40 AD/B - HMC 5/16 - 5.91 0.313 0.866 1.949 5.906 3.937 1.063 M6x1.0mm
WL100HCR CAT50 AD/B - HCR 12 - 80.5 12 32 49.5 80.5 31.5 37 WK028HMC CAT40 AD/B - HMC 3/8 - 4.72 0.375 0.945 1.949 4.724 2.756 1.260 M8x1.0mm
WL102HCR 50 CAT50 AD/B - HCR 20 - 80.5 20 42 49.5 80.5 34 42 WK030HMC 40 CAT40 AD/B - HMC 3/8 - 5.91 0.375 0.945 1.949 5.906 3.937 1.260 M8x1.0mm
WL104HCR CAT50 AD/B - HCR 32 - 100 32 60 60 100 - 55 WK032HMC CAT40 AD/B - HMC 1/2 - 4.72 0.500 1.024 1.949 4.724 2.756 1.457 M10x1.0mm
WK034HMC CAT40 AD/B - HMC 1/2 - 5.91 0.500 1.024 1.949 5.906 3.937 1.457 M10x1.0mm
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WK036HMC CAT40 AD/B - HMC 5/8 - 4.72 0.625 1.260 1.949 4.724 2.756 1.654 M12x1.0mm
WK038HMC CAT40 AD/B - HMC 5/8 - 5.91 0.625 1.260 1.949 5.906 3.937 1.654 M12x1.0mm
WK040HMC CAT40 AD/B - HMC 3/4 - 4.72 0.750 1.339 1.949 4.724 2.756 1.654 M16x1.0mm
WK042HMC CAT40 AD/B - HMC 3/4 - 5.91 0.750 1.339 1.949 5.906 3.937 1.654 M16x1.0mm
WL020HMC CAT50 AD/B - HMC 1/4 - 5.91 0.250 0.787 1.752 5.906 3.937 1.063 M5x0.8mm
WL022HMC CAT50 AD/B - HMC 5/16 - 5.91 0.313 0.866 1.752 5.906 3.937 1.063 M6x1.0mm
WL024HMC 50 CAT50 AD/B - HMC 3/8 - 5.91 0.375 0.945 1.752 5.906 3.937 1.260 M8x1.0mm
WL026HMC CAT50 AD/B - HMC 1/2 - 5.91 0.500 1.024 1.752 5.906 3.937 1.457 M10x1.0mm
WL028HMC CAT50 AD/B - HMC 5/8 - 5.91 0.625 1.260 1.752 5.906 3.937 1.654 M12x1.0mm
WL030HMC CAT50 AD/B - HMC 3/4 - 5.91 0.750 1.339 1.752 5.906 3.937 1.654 M16x1.0mm
Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
WK100HMC CAT40 AD/B - HMC 6 - 120 6 20 49.5 120 70 27 M5X0.8
WK102HMC CAT40 AD/B - HMC 6 - 150 6 20 49.5 150 100 27 M5X0.8
WK104HMC CAT40 AD/B - HMC 8 - 120 8 22 49.5 120 70 27 M6X1.0
WK106HMC CAT40 AD/B - HMC 8 - 150 8 22 49.5 150 100 27 M6X1.0
WK108HMC CAT40 AD/B - HMC 10 - 120 10 24 49.5 120 70 32 M8X1.0
WK110HMC CAT40 AD/B - HMC 10 - 150 10 24 49.5 150 100 32 M8X1.0
WK112HMC 40 CAT40 AD/B - HMC 12 - 120 12 25 49.5 120 70 37 M10X1.0
WK114HMC CAT40 AD/B - HMC 12 - 150 12 25 49.5 150 100 37 M10X1.0
WK116HMC CAT40 AD/B - HMC 16 - 120 16 32 49.5 120 70 42 M12X1.0
WK118HMC CAT40 AD/B - HMC 16 - 150 16 32 49.5 150 100 42 M12X1.0
WK120HMC CAT40 AD/B - HMC 20 - 120 20 34 49.5 120 70 42 M16X1.0
WK122HMC CAT40 AD/B - HMC 20 - 150 20 34 49.5 150 100 42 M16X1.0
WL100HMC CAT50 AD/B - HMC 6 - 150 6 20 44.5 150 100 27 M5X0.8
WL102HMC CAT50 AD/B - HMC 8 - 150 8 22 44.5 150 100 27 M6X1.0
WL104HMC 50 CAT50 AD/B - HMC 10 - 150 10 24 44.5 150 100 32 M8X1.0
WL106HMC CAT50 AD/B - HMC 12 - 150 12 25 44.5 150 100 37 M10X1.0
WL108HMC CAT50 AD/B - HMC 16 - 150 16 32 44.5 150 100 42 M12X1.0
WL110HMC CAT50 AD/B - HMC 20 - 150 20 34 44.5 150 100 42 M16X1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
1312 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1313

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


BT BT
HYDRAULIC CHUCK (SLIM) HYDRAULIC CHUCK (SLIM)


G L2 G L2




d1 D1 D2 d1 D1 D2


L1 L1
TAPER No. L TAPER No. L


Taper G Value RPM Run-Out Coolant
JIS B6339 Accuracy (at 3D) System Taper Run-Out Coolant
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B JIS B6339 Accuracy G Value RPM (at 3D) System
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B
JIS B6339/MAS 403-BT Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G JIS B6339/MAS 403-BT Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
WG020 BT30 - HC 1/4 - 2.75 0.250 1.024 1.752 2.750 1.161 1.063 M5x0.8mm
WG022 BT30 - HC 5/16 - 2.75 0.313 1.102 1.752 2.750 1.181 1.063 M6x1.0mm WG100 BT30 - HC 6 - 70 6 26 44.5 70 29.5 27 M5x0.8
WG102 BT30 - HC 8 - 70 8 28 44.5 70 30 27 M6x1.0
WG024 BT30 - HC 3/8 - 2.95 0.375 1.181 1.752 2.953 1.220 1.260 M8x1.0mm WG104 BT30 - HC 10 - 75 10 30 44.5 75 31 32 M8x1.0
30
WG026 BT30 - HC 1/2 - 3.35 0.500 1.260 1.772 3.346 1.575 1.457 M10x1.0mm WG106 30 BT30 - HC 12 - 85 12 32 45 85 45 37 M10x1.0
WG028 BT30 - HC 5/8 - 3.54 0.625 1.496 1.772 3.543 1.811 1.654 M10x1.0mm WG108 BT30 - HC 14 - 85 14 34 45 85 45 37 M10x1.0
WG110 BT30 - HC 16 - 90 16 38 45 90 50 42 M10x1.0
WG030 BT30 - HC 3/4 - 3.54 0.750 1.654 1.772 3.543 1.890 1.654 M6x1.0mm
WG112 BT30 - HC 18 - 90 18 40 45 90 50 42 M10x1.0
WH020 BT40 AD/B - HC 1/4 - 3.54 0.250 1.024 1.752 3.543 1.181 1.063 M5x0.8mm WG114 BT30 - HC 20 - 90 20 42 45 90 50 42 M6x1.0
WH022 BT40 AD/B - HC 5/16 - 3.54 0.313 1.102 1.752 3.543 1.280 1.063 M6x1.0mm WH100 BT40 AD/B - HC 6 - 90 6 26 44.5 90 43 27 M5x0.8
WH024 BT40 AD/B - HC 3/8 - 3.54 0.375 1.181 1.752 3.543 1.260 1.260 M8x1.0mm WH102 BT40 AD/B - HC 8 - 90 8 28 44.5 90 44.5 27 M6x1.0
WH104 BT40 AD/B - HC 10 - 90 10 30 44.5 90 44.5 32 M8x1.0
WH026 40 BT40 AD/B - HC 1/2 - 3.54 0.500 1.260 1.752 3.543 1.378 1.457 M10x1.0mm WH106 BT40 AD/B - HC 12 - 90 12 32 44.5 90 44.5 37 M10x1.0
WH028 BT40 AD/B - HC 5/8 - 3.54 0.625 1.496 1.870 3.543 1.575 1.654 M12x1.0mm WH108 BT40 AD/B - HC 14 - 90 14 34 44.5 90 44.5 37 M10x1.0
WH030 BT40 AD/B - HC 3/4 - 3.54 0.750 1.654 1.870 3.543 1.575 1.654 M16x1.0mm WH110 40 BT40 AD/B - HC 16 - 90 16 38 44.5 90 47.5 42 M12x1.0
WH032 BT40 AD/B - HC 1" - 3.94 1.000 1.969 2.362 3.937 1.772 1.890 M16x1.0mm WH112 BT40 AD/B - HC 18 - 90 18 40 44.5 90 47.5 42 M12x1.0
WH114 BT40 AD/B - HC 20 - 90 20 42 44.5 90 47.5 42 M16x1.0
WH034 BT40 AD/B - HC 1 1/4 - 4.13 1.250 2.362 - 4.134 - 2.165 M16x1.0mm
WH116 BT40 AD/B - HC 25 - 100 25 50 60 100 47.5 48 M16x1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WH118 BT40 AD/B - HC 32 - 105 32 60 - 105 - 55 M16x1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.























1314 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1315

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


BT BT
HYDRAULIC CHUCK (SLIM) HYDRAULIC CHUCK (SLIM)


G L2 G L2




d1 D1 D2 d1 D1 D2


L1 L1
TAPER No. L TAPER No. L


Taper G Value RPM Run-Out Coolant
JIS B6339 Accuracy (at 3D) System Taper Run-Out Coolant
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B JIS B6339 Accuracy G Value RPM (at 3D) System
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B
JIS B6339/MAS 403-BT Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G JIS B6339/MAS 403-BT Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
WG020 BT30 - HC 1/4 - 2.75 0.250 1.024 1.752 2.750 1.161 1.063 M5x0.8mm
WG022 BT30 - HC 5/16 - 2.75 0.313 1.102 1.752 2.750 1.181 1.063 M6x1.0mm WG100 BT30 - HC 6 - 70 6 26 44.5 70 29.5 27 M5x0.8
WG102 BT30 - HC 8 - 70 8 28 44.5 70 30 27 M6x1.0
WG024 BT30 - HC 3/8 - 2.95 0.375 1.181 1.752 2.953 1.220 1.260 M8x1.0mm WG104 BT30 - HC 10 - 75 10 30 44.5 75 31 32 M8x1.0
30
WG026 BT30 - HC 1/2 - 3.35 0.500 1.260 1.772 3.346 1.575 1.457 M10x1.0mm WG106 30 BT30 - HC 12 - 85 12 32 45 85 45 37 M10x1.0
WG028 BT30 - HC 5/8 - 3.54 0.625 1.496 1.772 3.543 1.811 1.654 M10x1.0mm WG108 BT30 - HC 14 - 85 14 34 45 85 45 37 M10x1.0
WG110 BT30 - HC 16 - 90 16 38 45 90 50 42 M10x1.0
WG030 BT30 - HC 3/4 - 3.54 0.750 1.654 1.772 3.543 1.890 1.654 M6x1.0mm
WG112 BT30 - HC 18 - 90 18 40 45 90 50 42 M10x1.0
WH020 BT40 AD/B - HC 1/4 - 3.54 0.250 1.024 1.752 3.543 1.181 1.063 M5x0.8mm WG114 BT30 - HC 20 - 90 20 42 45 90 50 42 M6x1.0
WH022 BT40 AD/B - HC 5/16 - 3.54 0.313 1.102 1.752 3.543 1.280 1.063 M6x1.0mm WH100 BT40 AD/B - HC 6 - 90 6 26 44.5 90 43 27 M5x0.8
WH024 BT40 AD/B - HC 3/8 - 3.54 0.375 1.181 1.752 3.543 1.260 1.260 M8x1.0mm WH102 BT40 AD/B - HC 8 - 90 8 28 44.5 90 44.5 27 M6x1.0
WH104 BT40 AD/B - HC 10 - 90 10 30 44.5 90 44.5 32 M8x1.0
WH026 40 BT40 AD/B - HC 1/2 - 3.54 0.500 1.260 1.752 3.543 1.378 1.457 M10x1.0mm WH106 BT40 AD/B - HC 12 - 90 12 32 44.5 90 44.5 37 M10x1.0
WH028 BT40 AD/B - HC 5/8 - 3.54 0.625 1.496 1.870 3.543 1.575 1.654 M12x1.0mm WH108 BT40 AD/B - HC 14 - 90 14 34 44.5 90 44.5 37 M10x1.0
WH030 BT40 AD/B - HC 3/4 - 3.54 0.750 1.654 1.870 3.543 1.575 1.654 M16x1.0mm WH110 40 BT40 AD/B - HC 16 - 90 16 38 44.5 90 47.5 42 M12x1.0
WH032 BT40 AD/B - HC 1" - 3.94 1.000 1.969 2.362 3.937 1.772 1.890 M16x1.0mm WH112 BT40 AD/B - HC 18 - 90 18 40 44.5 90 47.5 42 M12x1.0
WH114 BT40 AD/B - HC 20 - 90 20 42 44.5 90 47.5 42 M16x1.0
WH034 BT40 AD/B - HC 1 1/4 - 4.13 1.250 2.362 - 4.134 - 2.165 M16x1.0mm
WH116 BT40 AD/B - HC 25 - 100 25 50 60 100 47.5 48 M16x1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WH118 BT40 AD/B - HC 32 - 105 32 60 - 105 - 55 M16x1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.























1314 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1315

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


BT BT
HYDRAULIC CHUCK (Power E Hydro) HYDRAULIC CHUCK (Short & Rigid)

FIG.1 L2 G L2



d1 D1 D2 D3

TAPER No. d1 D1 D2
L
L2
FIG.2
TAPER No. L


d1 D1 D2 Taper G Value RPM Run-Out Coolant
JIS B6339 Accuracy (at 3D) System
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B
TAPER No.
JIS B6339/MAS 403-BT
L Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
Taper G Value RPM Run-Out Coolant
JIS B6339 Accuracy (at 3D) System WG100SNR 30 BT30 - HC 20S - 85 20 41 44 85 42 M6x1.0
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B WH100SNR BT40 AD/B - HC 12S - 58 12 32 42 58 37 M8x1.0
WH102SNR 40 BT40 AD/B - HC 20S - 72.5 20 38 49.25 72.5 42 M8x1.0
JIS B6339/MAS 403-BT Unit : inch
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WG002PE 30 BT30 - HC 3/4P - 3.543 0.75 1.496 1.653 1.751 3.543 1.889 M8x1.0mm 1
WH002PE 40 BT40 AD/B - HC 3/4P - 2.854 0.75 1.496 1.938 - 2.854 1.889 M8x1.0mm 2
WI003PE 50 BT50 AD/B - HC 1 1/4P - 3.543 1.25 2.303 2.834 - 3.543 2.244 M8x1.0mm 2


Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WG100PE BT30 - HC 12P - 69 12 32 42 44.5 69 41 M8x1.0 1
WG102PE 30 BT30 - HC 20P - 90 20 38 42 44.5 90 48 M8x1.0 1
WH100PE 40 BT40 AD/B - HC 12P - 58 12 32 42 - 58 41 M8x1.0 2
WH102PE BT40 AD/B - HC 20P - 72.5 20 38 49.25 - 72.5 48 M8x1.0 2
WI100PE 50 BT50 AD/B - HC 20P - 83.5 20 38 49.25 - 83.5 48 M8x1.0 2
WI102PE BT50 AD/B - HC 32P - 90 32 58.5 72 - 90 57 M8x1.0 2

* High Clamping Torque Power version
(Please refer to page 1420, Technical Information)
* Applicable for milling(roughing and finishing)
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.


















1316 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1317

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


BT BT
HYDRAULIC CHUCK (Power E Hydro) HYDRAULIC CHUCK (Short & Rigid)

FIG.1 L2 G L2



d1 D1 D2 D3

TAPER No. d1 D1 D2
L
L2
FIG.2
TAPER No. L


d1 D1 D2 Taper G Value RPM Run-Out Coolant
JIS B6339 Accuracy (at 3D) System
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B
TAPER No.
JIS B6339/MAS 403-BT
L Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
Taper G Value RPM Run-Out Coolant
JIS B6339 Accuracy (at 3D) System WG100SNR 30 BT30 - HC 20S - 85 20 41 44 85 42 M6x1.0
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B WH100SNR BT40 AD/B - HC 12S - 58 12 32 42 58 37 M8x1.0
WH102SNR 40 BT40 AD/B - HC 20S - 72.5 20 38 49.25 72.5 42 M8x1.0
JIS B6339/MAS 403-BT Unit : inch
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WG002PE 30 BT30 - HC 3/4P - 3.543 0.75 1.496 1.653 1.751 3.543 1.889 M8x1.0mm 1
WH002PE 40 BT40 AD/B - HC 3/4P - 2.854 0.75 1.496 1.938 - 2.854 1.889 M8x1.0mm 2
WI003PE 50 BT50 AD/B - HC 1 1/4P - 3.543 1.25 2.303 2.834 - 3.543 2.244 M8x1.0mm 2


Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WG100PE BT30 - HC 12P - 69 12 32 42 44.5 69 41 M8x1.0 1
WG102PE 30 BT30 - HC 20P - 90 20 38 42 44.5 90 48 M8x1.0 1
WH100PE 40 BT40 AD/B - HC 12P - 58 12 32 42 - 58 41 M8x1.0 2
WH102PE BT40 AD/B - HC 20P - 72.5 20 38 49.25 - 72.5 48 M8x1.0 2
WI100PE 50 BT50 AD/B - HC 20P - 83.5 20 38 49.25 - 83.5 48 M8x1.0 2
WI102PE BT50 AD/B - HC 32P - 90 32 58.5 72 - 90 57 M8x1.0 2

* High Clamping Torque Power version
(Please refer to page 1420, Technical Information)
* Applicable for milling(roughing and finishing)
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.


















1316 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1317

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


BT BT
HYDRAULIC CHUCK (RADIAL TOOL LENGTH PRE-SETTING TYPE) HYDRAULIC CHUCK (For MOULD)




Radial Length L2
Adjustment G
L2
B 3°

d1 D1 D2
AD d1 D1 D2
TAPER No. L1
L
L1
B
TAPER No. L
Taper G Value RPM Run-Out Coolant
Taper Run-Out Coolant JIS B6339 Accuracy (at 3D) System
JIS B6339 Accuracy G Value RPM (at 3D) System - BT
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B AT3 2.5 25,000 ≤0.00012" AD/B
JIS B6339/MAS 403-BT Unit : mm
JIS B6339/MAS 403-BT Unit : mm EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G

EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 WH100HMC BT40 AD/B - HMC 6 - 120 6 20 44.5 120 70 27 M5×0.8
WG100HCR 30 BT30 - HCR 12 - 85 12 32 44.5 85 40 37 WH102HMC BT40 AD/B - HMC 6 - 150 6 20 44.5 150 100 27 M5×0.8
WG102HCR BT30 - HCR 20 - 85 20 44 - 85 - 42 WH104HMC BT40 AD/B - HMC 8 - 120 8 22 44.5 120 70 27 M6×1.0
WH100HCR BT40 AD/B - HCR 12 - 90 12 32 44.5 90 42.5 37
WH102HCR 40 BT40 AD/B - HCR 20 - 90 20 42 44.5 90 47.5 42 WH106HMC BT40 AD/B - HMC 8 - 150 8 22 44.5 150 100 27 M6×1.0
WH104HCR BT40 AD/B - HCR 32 - 105 32 60 - 105 - 55 WH108HMC BT40 AD/B - HMC 10 - 120 10 24 44.5 120 70 32 M8×1.0
WH110HMC BT40 AD/B - HMC 10 - 150 10 24 44.5 150 100 32 M8×1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. 40
WH112HMC BT40 AD/B - HMC 12 - 120 12 25 44.5 120 70 37 M10×1.0
WH114HMC BT40 AD/B - HMC 12 - 150 12 25 44.5 150 100 37 M10×1.0
WH116HMC BT40 AD/B - HMC 16 - 120 16 32 44.5 120 70 42 M12×1.0
WH118HMC BT40 AD/B - HMC 16 - 150 16 32 44.5 150 100 42 M12×1.0
WH120HMC BT40 AD/B - HMC 20 - 120 20 36 43.75 120 - 42 M16×1.0
WH122HMC BT40 AD/B - HMC 20 - 150 20 36 46.9 150 - 42 M16×1.0

* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.



























1318 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1319

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


BT BT
HYDRAULIC CHUCK (RADIAL TOOL LENGTH PRE-SETTING TYPE) HYDRAULIC CHUCK (For MOULD)




Radial Length L2
Adjustment G
L2
B 3°

d1 D1 D2
AD d1 D1 D2
TAPER No. L1
L
L1
B
TAPER No. L
Taper G Value RPM Run-Out Coolant
Taper Run-Out Coolant JIS B6339 Accuracy (at 3D) System
JIS B6339 Accuracy G Value RPM (at 3D) System - BT
- BT AT3 2.5 25,000 ≤0.00012" AD or AD/B AT3 2.5 25,000 ≤0.00012" AD/B
JIS B6339/MAS 403-BT Unit : mm
JIS B6339/MAS 403-BT Unit : mm EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G

EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 WH100HMC BT40 AD/B - HMC 6 - 120 6 20 44.5 120 70 27 M5×0.8
WG100HCR 30 BT30 - HCR 12 - 85 12 32 44.5 85 40 37 WH102HMC BT40 AD/B - HMC 6 - 150 6 20 44.5 150 100 27 M5×0.8
WG102HCR BT30 - HCR 20 - 85 20 44 - 85 - 42 WH104HMC BT40 AD/B - HMC 8 - 120 8 22 44.5 120 70 27 M6×1.0
WH100HCR BT40 AD/B - HCR 12 - 90 12 32 44.5 90 42.5 37
WH102HCR 40 BT40 AD/B - HCR 20 - 90 20 42 44.5 90 47.5 42 WH106HMC BT40 AD/B - HMC 8 - 150 8 22 44.5 150 100 27 M6×1.0
WH104HCR BT40 AD/B - HCR 32 - 105 32 60 - 105 - 55 WH108HMC BT40 AD/B - HMC 10 - 120 10 24 44.5 120 70 32 M8×1.0
WH110HMC BT40 AD/B - HMC 10 - 150 10 24 44.5 150 100 32 M8×1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. 40
WH112HMC BT40 AD/B - HMC 12 - 120 12 25 44.5 120 70 37 M10×1.0
WH114HMC BT40 AD/B - HMC 12 - 150 12 25 44.5 150 100 37 M10×1.0
WH116HMC BT40 AD/B - HMC 16 - 120 16 32 44.5 120 70 42 M12×1.0
WH118HMC BT40 AD/B - HMC 16 - 150 16 32 44.5 150 100 42 M12×1.0
WH120HMC BT40 AD/B - HMC 20 - 120 20 36 43.75 120 - 42 M16×1.0
WH122HMC BT40 AD/B - HMC 20 - 150 20 36 46.9 150 - 42 M16×1.0

* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.



























1318 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1319

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CCT CCT
DUAL CONTACT HYDRAULIC CHUCK (SLIM) HYDRAULIC CHUCK (Power E Hydro)

G L2
G L2





d1 D1 D2
d1 D1 D2


TAPER No.
L1 TAPER No. L
L

Taper Run-Out Coolant
Accuracy G Value RPM (at 3D) System
CCT
Taper G Value RPM Run-Out Coolant AT3 2.5 25,000 ≤0.00012" AD/B
Accuracy (at 3D) System
CCT
AT3 2.5 25,000 ≤0.00012" AD/B CCT (CAT DUAL CONTACT) Unit : inch
CCT (CAT DUAL CONTACT) Unit : inch EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G WB030PE 40 CCT40 AD/B - HC 3/4P - 2.539 0.75 1.496 49.25 2.539 1.889 M8x1.0mm
WB031PE CCT40 AD/B - HC 3/4P - 4.000 0.75 1.496 49.25 4.000 1.889 M8x1.0mm
WB020 CCT40 AD/B - HC 1/4 - 3.54 0.250 1.024 1.752 3.543 1.280 1.063 M5x0.8mm
WB022 CCT40 AD/B - HC 5/16 - 3.54 0.313 1.102 1.752 3.543 1.280 1.063 M6x1.0mm Unit : mm
WB024 CCT40 AD/B - HC 3/8 - 3.54 0.375 1.181 1.752 3.543 1.634 1.260 M8x1.0mm EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
WB026 CCT40 AD/B - HC 1/2 - 3.54 0.500 1.260 1.752 3.543 1.634 1.457 M10x1.0mm WB130PE CCT40 AD/B - HC 20P - 64.5 20 38 49.25 64.5 48 M8x1.0
WB028 40 CCT40 AD/B - HC 5/8 - 3.54 0.625 1.496 1.752 3.543 1.949 1.654 M10x1.0mm WB131PE 40 CCT40 AD/B - HC 20P - 101.6 20 38 49.25 101.6 48 M8x1.0
WB030 CCT40 AD/B - HC 3/4 - 3.54 0.750 1.654 1.752 3.543 1.949 1.654 M10x1.0mm
WB032 CCT40 AD/B - HC 1" - 3.94 1.000 2.165 2.480 3.937 2.559 1.890 M16x1.0mm * High Clamping Torque Power version
WB034 CCT40 AD/B - HC 1 1/4 - 4.13 1.250 2.480 3.150 4.134 1.378 2.165 M16x1.0mm (Please refer to page 1420, Technical Information)
WC020 CCT50 AD/B - HC 1/4 - 3.54 0.250 1.024 1.969 3.543 1.181 1.063 M5x0.8mm * Applicable for milling(roughing and finishing)
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
WC022 CCT50 AD/B - HC 5/16 - 3.54 0.313 1.102 1.969 3.543 1.181 1.063 M6x1.0mm
WC024 CCT50 AD/B - HC 3/8 - 3.54 0.375 1.181 1.969 3.543 1.260 1.260 M8x1.0mm
WC026 50 CCT50 AD/B - HC 1/2 - 3.54 0.500 1.260 1.969 3.543 1.378 1.457 M10x1.0mm
WC028 CCT50 AD/B - HC 5/8 - 3.54 0.625 1.496 1.969 3.543 1.575 1.654 M10x1.0mm
WC030 CCT50 AD/B - HC 3/4 - 3.54 0.750 1.654 1.969 3.543 1.575 1.654 M10x1.0mm
WC032 CCT50 AD/B - HC 1" - 4.13 1.000 2.244 2.480 4.134 2.047 1.890 M16x1.0mm
WC034 CCT50 AD/B - HC 1 1/4 - 4.53 1.250 2.480 2.953 4.528 2.441 2.165 M16x1.0mm
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
























1320 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1321

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CCT CCT
DUAL CONTACT HYDRAULIC CHUCK (SLIM) HYDRAULIC CHUCK (Power E Hydro)

G L2
G L2





d1 D1 D2
d1 D1 D2


TAPER No.
L1 TAPER No. L
L

Taper Run-Out Coolant
Accuracy G Value RPM (at 3D) System
CCT
Taper G Value RPM Run-Out Coolant AT3 2.5 25,000 ≤0.00012" AD/B
Accuracy (at 3D) System
CCT
AT3 2.5 25,000 ≤0.00012" AD/B CCT (CAT DUAL CONTACT) Unit : inch
CCT (CAT DUAL CONTACT) Unit : inch EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G WB030PE 40 CCT40 AD/B - HC 3/4P - 2.539 0.75 1.496 49.25 2.539 1.889 M8x1.0mm
WB031PE CCT40 AD/B - HC 3/4P - 4.000 0.75 1.496 49.25 4.000 1.889 M8x1.0mm
WB020 CCT40 AD/B - HC 1/4 - 3.54 0.250 1.024 1.752 3.543 1.280 1.063 M5x0.8mm
WB022 CCT40 AD/B - HC 5/16 - 3.54 0.313 1.102 1.752 3.543 1.280 1.063 M6x1.0mm Unit : mm
WB024 CCT40 AD/B - HC 3/8 - 3.54 0.375 1.181 1.752 3.543 1.634 1.260 M8x1.0mm EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
WB026 CCT40 AD/B - HC 1/2 - 3.54 0.500 1.260 1.752 3.543 1.634 1.457 M10x1.0mm WB130PE CCT40 AD/B - HC 20P - 64.5 20 38 49.25 64.5 48 M8x1.0
WB028 40 CCT40 AD/B - HC 5/8 - 3.54 0.625 1.496 1.752 3.543 1.949 1.654 M10x1.0mm WB131PE 40 CCT40 AD/B - HC 20P - 101.6 20 38 49.25 101.6 48 M8x1.0
WB030 CCT40 AD/B - HC 3/4 - 3.54 0.750 1.654 1.752 3.543 1.949 1.654 M10x1.0mm
WB032 CCT40 AD/B - HC 1" - 3.94 1.000 2.165 2.480 3.937 2.559 1.890 M16x1.0mm * High Clamping Torque Power version
WB034 CCT40 AD/B - HC 1 1/4 - 4.13 1.250 2.480 3.150 4.134 1.378 2.165 M16x1.0mm (Please refer to page 1420, Technical Information)
WC020 CCT50 AD/B - HC 1/4 - 3.54 0.250 1.024 1.969 3.543 1.181 1.063 M5x0.8mm * Applicable for milling(roughing and finishing)
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
WC022 CCT50 AD/B - HC 5/16 - 3.54 0.313 1.102 1.969 3.543 1.181 1.063 M6x1.0mm
WC024 CCT50 AD/B - HC 3/8 - 3.54 0.375 1.181 1.969 3.543 1.260 1.260 M8x1.0mm
WC026 50 CCT50 AD/B - HC 1/2 - 3.54 0.500 1.260 1.969 3.543 1.378 1.457 M10x1.0mm
WC028 CCT50 AD/B - HC 5/8 - 3.54 0.625 1.496 1.969 3.543 1.575 1.654 M10x1.0mm
WC030 CCT50 AD/B - HC 3/4 - 3.54 0.750 1.654 1.969 3.543 1.575 1.654 M10x1.0mm
WC032 CCT50 AD/B - HC 1" - 4.13 1.000 2.244 2.480 4.134 2.047 1.890 M16x1.0mm
WC034 CCT50 AD/B - HC 1 1/4 - 4.53 1.250 2.480 2.953 4.528 2.441 2.165 M16x1.0mm
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
























1320 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1321

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CCT CBT
DUAL CONTACT HYDRAULIC CHUCK (For MOULD) DUAL CONTACT HYDRAULIC CHUCK (SLIM)


G
L2 L2
G
3°
d1 D1 D2
d1 D1 D2

L1
L
L1
TAPER No.
L

Taper Run-Out Coolant
Accuracy G Value RPM (at 3D) System Taper Run-Out Coolant
CCT Accuracy G Value RPM (at 3D) System
AT3 2.5 25,000 ≤0.00012" AD/B CBT AT3 2.5 25,000 ≤0.00012" AD
CCT (CAT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G CBT (BT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
WB020HMC CCT40 AD/B - HMC 1/4 - 4.72 0.250 0.787 1.949 4.724 2.756 1.063 M5x0.8mm
WB022HMC CCT40 AD/B - HMC 1/4 - 5.91 0.250 0.787 1.949 5.906 3.937 1.063 M5x0.8mm WD020 CBT 30 - HC 1/4 - 2.76 0.250 1.024 1.752 2.756 1.161 1.063 M5x0.8mm
WB024HMC CCT40 AD/B - HMC 5/16 - 4.72 0.313 0.866 1.949 4.724 2.756 1.063 M6x1.0mm WD022 CBT 30 - HC 5/16 - 2.76 0.313 1.102 1.752 2.756 1.181 1.063 M6x1.0mm
WB026HMC CCT40 AD/B - HMC 5/16 - 5.91 0.313 0.866 1.949 5.906 3.937 1.063 M6x1.0mm WD024 CBT 30 - HC 3/8 - 2.95 0.375 1.181 1.752 2.953 1.220 1.260 M8x1.0mm
WB028HMC CCT40 AD/B - HMC 3/8 - 4.72 0.375 0.945 1.949 4.724 2.756 1.260 M8x1.0mm WD026 30 CBT 30 - HC 1/2 - 3.35 0.500 1.260 1.772 3.346 1.575 1.457 M10x1.0mm
WB030HMC 40 CCT40 AD/B - HMC 3/8 - 5.91 0.375 0.945 1.949 5.906 3.937 1.260 M8x1.0mm WD028 CBT 30 - HC 5/8 - 3.54 0.625 1.496 1.772 3.543 1.811 1.654 M10x1.0mm
WB032HMC CCT40 AD/B - HMC 1/2 - 4.72 0.500 1.024 1.949 4.724 2.756 1.457 M10x1.0mm WD030 CBT 30 - HC 3/4 - 3.54 0.750 1.654 1.772 3.543 1.890 1.654 M16x1.0mm
WB034HMC CCT40 AD/B - HMC 1/2 - 5.91 0.500 1.024 1.949 5.906 3.937 1.457 M10x1.0mm WE020 CBT 40 - HC 1/4 - 3.54 0.250 1.024 1.752 3.543 1.181 1.063 M5x0.8mm
WB036HMC CCT40 AD/B - HMC 5/8 - 4.72 0.625 1.260 1.949 4.724 2.756 1.654 M12x1.0mm WE022 CBT 40 - HC 5/16 - 3.54 0.313 1.102 1.752 3.543 1.280 1.063 M6x1.0mm
WB038HMC CCT40 AD/B - HMC 5/8 - 5.91 0.625 1.260 1.949 5.906 3.937 1.654 M12x1.0mm WE024 CBT 40 - HC 3/8 - 3.54 0.375 1.181 1.752 3.543 1.260 1.260 M8x1.0mm
WB040HMC CCT40 AD/B - HMC 3/4 - 4.72 0.750 1.339 1.949 4.724 2.756 1.654 M16x1.0mm WE026 CBT 40 - HC 1/2 - 3.54 0.500 1.260 1.752 3.543 1.378 1.457 M10x1.0mm
WB042HMC CCT40 AD/B - HMC 3/4 - 5.91 0.750 1.339 1.949 5.906 3.937 1.654 M16x1.0mm WE028 40
WC020HMC CCT50 AD/B - HMC 1/4 - 5.91 0.250 0.787 1.752 5.906 3.937 1.063 M5x0.8mm CBT 40 - HC 5/8 - 3.54 0.625 1.496 1.870 3.543 1.575 1.654 M12x1.0mm
WC022HMC CCT50 AD/B - HMC 5/16 - 5.91 0.313 0.866 1.752 5.906 3.937 1.063 M6x1.0mm WE030 CBT 40 - HC 3/4 - 3.54 0.750 1.654 1.870 3.543 1.575 1.654 M16x1.0mm
WC024HMC 50 CCT50 AD/B - HMC 3/8 - 5.91 0.375 0.945 1.752 5.906 3.937 1.260 M8x1.0mm WE032 CBT 40 - HC 1 - 3.94 1.000 1.969 2.362 3.937 1.772 1.890 M16x1.0mm
WC026HMC CCT50 AD/B - HMC 1/2 - 5.91 0.500 1.024 1.752 5.906 3.937 1.457 M10x1.0mm WE034 CBT 40 - HC 1 1/4 - 4.13 1.250 2.362 - 4.134 - 2.165 M16x1.0mm
WC028HMC CCT50 AD/B - HMC 5/8 - 5.91 0.625 1.260 1.752 5.906 3.937 1.654 M12x1.0mm
WC030HMC CCT50 AD/B - HMC 3/4 - 5.91 0.750 1.339 1.752 5.906 3.937 1.654 M16x1.0mm Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
Unit : mm
WD100 CBT 30 - HC 6 - 70 6 26 44.5 70 29.5 27 M5x0.8
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G WD102 CBT 30 - HC 8 - 70 8 28 44.5 70 30 27 M6x1.0
WB100HMC CCT40 AD/B - HMC 6 - 120 6 20 49.5 120 70 27 M5X0.8 WD104 CBT 30 - HC 10 - 75 10 30 44.5 75 31 32 M8x1.0
WB102HMC CCT40 AD/B - HMC 6 - 150 6 20 49.5 150 100 27 M5X0.8 WD106 30 CBT 30 - HC 12 - 85 12 32 45 85 45 37 M10x1.0
WB104HMC CCT40 AD/B - HMC 8 - 120 8 22 49.5 120 70 27 M6X1.0 WD108 CBT 30 - HC 14 - 85 14 34 45 85 45 37 M10x1.0
WB106HMC CCT40 AD/B - HMC 8 - 150 8 22 49.5 150 100 27 M6X1.0 WD110 CBT 30 - HC 16 - 90 16 38 45 90 50 42 M10x1.0
WB108HMC CCT40 AD/B - HMC 10 - 120 10 24 49.5 120 70 32 M8X1.0 WD112 CBT 30 - HC 18 - 90 18 40 45 90 50 42 M10x1.0
WB110HMC 40 CCT40 AD/B - HMC 10 - 150 10 24 49.5 150 100 32 M8X1.0 WD114 CBT 30 - HC 20 - 90 20 42 45 90 50 42 M6x1.0
WB112HMC CCT40 AD/B - HMC 12 - 120 12 25 49.5 120 70 37 M10X1.0 WE100 CBT 40 - HC 6 - 90 6 26 44.5 90 43 27 M5x0.8
WB114HMC CCT40 AD/B - HMC 12 - 150 12 25 49.5 150 100 37 M10X1.0 WE102 CBT 40 - HC 8 - 90 8 28 44.5 90 44.5 27 M6x1.0
WB116HMC CCT40 AD/B - HMC 16 - 120 16 32 49.5 120 70 42 M12X1.0 WE104 CBT 40 - HC 10 - 90 10 30 44.5 90 44.5 32 M8x1.0
WB118HMC CCT40 AD/B - HMC 16 - 150 16 32 49.5 150 100 42 M12X1.0 WE106 CBT 40 - HC 12 - 90 12 32 44.5 90 44.5 37 M10x1.0
WB120HMC CCT40 AD/B - HMC 20 - 120 20 34 49.5 120 70 42 M16X1.0 WE108 CBT 40 - HC 14 - 90 14 34 44.5 90 44.5 37 M10x1.0
WB122HMC CCT40 AD/B - HMC 20 - 150 20 34 49.5 150 100 42 M16X1.0 WE110 40 CBT 40 - HC 16 - 90 16 38 44.5 90 47.5 42 M12x1.0
WC100HMC CCT50 AD/B - HMC 6 - 150 6 20 44.5 150 100 27 M5X0.8 WE112 CBT 40 - HC 18 - 90 18 40 44.5 90 47.5 42 M12x1.0
WC102HMC CCT50 AD/B - HMC 8 - 150 8 22 44.5 150 100 27 M6X1.0 WE114 CBT 40 - HC 20 - 90 20 42 44.5 90 47.5 42 M16x1.0
WC104HMC 50 CCT50 AD/B - HMC 10 - 150 10 24 44.5 150 100 32 M8X1.0 WE116 CBT 40 - HC 25 - 100 25 50 60 100 47.5 48 M16x1.0
WC106HMC CCT50 AD/B - HMC 12 - 150 12 25 44.5 150 100 37 M10X1.0
WC108HMC CCT50 AD/B - HMC 16 - 150 16 32 44.5 150 100 42 M12X1.0 WE118 CBT 40 - HC 32 - 105 32 60 - 105 - 55 M16x1.0
WC110HMC CCT50 AD/B - HMC 20 - 150 20 34 44.5 150 100 42 M16X1.0 * Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
1322 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1323

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


CCT CBT
DUAL CONTACT HYDRAULIC CHUCK (For MOULD) DUAL CONTACT HYDRAULIC CHUCK (SLIM)


G
L2 L2
G
3°
d1 D1 D2
d1 D1 D2

L1
L
L1
TAPER No.
L

Taper Run-Out Coolant
Accuracy G Value RPM (at 3D) System Taper Run-Out Coolant
CCT Accuracy G Value RPM (at 3D) System
AT3 2.5 25,000 ≤0.00012" AD/B CBT AT3 2.5 25,000 ≤0.00012" AD
CCT (CAT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G CBT (BT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
WB020HMC CCT40 AD/B - HMC 1/4 - 4.72 0.250 0.787 1.949 4.724 2.756 1.063 M5x0.8mm
WB022HMC CCT40 AD/B - HMC 1/4 - 5.91 0.250 0.787 1.949 5.906 3.937 1.063 M5x0.8mm WD020 CBT 30 - HC 1/4 - 2.76 0.250 1.024 1.752 2.756 1.161 1.063 M5x0.8mm
WB024HMC CCT40 AD/B - HMC 5/16 - 4.72 0.313 0.866 1.949 4.724 2.756 1.063 M6x1.0mm WD022 CBT 30 - HC 5/16 - 2.76 0.313 1.102 1.752 2.756 1.181 1.063 M6x1.0mm
WB026HMC CCT40 AD/B - HMC 5/16 - 5.91 0.313 0.866 1.949 5.906 3.937 1.063 M6x1.0mm WD024 CBT 30 - HC 3/8 - 2.95 0.375 1.181 1.752 2.953 1.220 1.260 M8x1.0mm
WB028HMC CCT40 AD/B - HMC 3/8 - 4.72 0.375 0.945 1.949 4.724 2.756 1.260 M8x1.0mm WD026 30 CBT 30 - HC 1/2 - 3.35 0.500 1.260 1.772 3.346 1.575 1.457 M10x1.0mm
WB030HMC 40 CCT40 AD/B - HMC 3/8 - 5.91 0.375 0.945 1.949 5.906 3.937 1.260 M8x1.0mm WD028 CBT 30 - HC 5/8 - 3.54 0.625 1.496 1.772 3.543 1.811 1.654 M10x1.0mm
WB032HMC CCT40 AD/B - HMC 1/2 - 4.72 0.500 1.024 1.949 4.724 2.756 1.457 M10x1.0mm WD030 CBT 30 - HC 3/4 - 3.54 0.750 1.654 1.772 3.543 1.890 1.654 M16x1.0mm
WB034HMC CCT40 AD/B - HMC 1/2 - 5.91 0.500 1.024 1.949 5.906 3.937 1.457 M10x1.0mm WE020 CBT 40 - HC 1/4 - 3.54 0.250 1.024 1.752 3.543 1.181 1.063 M5x0.8mm
WB036HMC CCT40 AD/B - HMC 5/8 - 4.72 0.625 1.260 1.949 4.724 2.756 1.654 M12x1.0mm WE022 CBT 40 - HC 5/16 - 3.54 0.313 1.102 1.752 3.543 1.280 1.063 M6x1.0mm
WB038HMC CCT40 AD/B - HMC 5/8 - 5.91 0.625 1.260 1.949 5.906 3.937 1.654 M12x1.0mm WE024 CBT 40 - HC 3/8 - 3.54 0.375 1.181 1.752 3.543 1.260 1.260 M8x1.0mm
WB040HMC CCT40 AD/B - HMC 3/4 - 4.72 0.750 1.339 1.949 4.724 2.756 1.654 M16x1.0mm WE026 CBT 40 - HC 1/2 - 3.54 0.500 1.260 1.752 3.543 1.378 1.457 M10x1.0mm
WB042HMC CCT40 AD/B - HMC 3/4 - 5.91 0.750 1.339 1.949 5.906 3.937 1.654 M16x1.0mm WE028 40
WC020HMC CCT50 AD/B - HMC 1/4 - 5.91 0.250 0.787 1.752 5.906 3.937 1.063 M5x0.8mm CBT 40 - HC 5/8 - 3.54 0.625 1.496 1.870 3.543 1.575 1.654 M12x1.0mm
WC022HMC CCT50 AD/B - HMC 5/16 - 5.91 0.313 0.866 1.752 5.906 3.937 1.063 M6x1.0mm WE030 CBT 40 - HC 3/4 - 3.54 0.750 1.654 1.870 3.543 1.575 1.654 M16x1.0mm
WC024HMC 50 CCT50 AD/B - HMC 3/8 - 5.91 0.375 0.945 1.752 5.906 3.937 1.260 M8x1.0mm WE032 CBT 40 - HC 1 - 3.94 1.000 1.969 2.362 3.937 1.772 1.890 M16x1.0mm
WC026HMC CCT50 AD/B - HMC 1/2 - 5.91 0.500 1.024 1.752 5.906 3.937 1.457 M10x1.0mm WE034 CBT 40 - HC 1 1/4 - 4.13 1.250 2.362 - 4.134 - 2.165 M16x1.0mm
WC028HMC CCT50 AD/B - HMC 5/8 - 5.91 0.625 1.260 1.752 5.906 3.937 1.654 M12x1.0mm
WC030HMC CCT50 AD/B - HMC 3/4 - 5.91 0.750 1.339 1.752 5.906 3.937 1.654 M16x1.0mm Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
Unit : mm
WD100 CBT 30 - HC 6 - 70 6 26 44.5 70 29.5 27 M5x0.8
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G WD102 CBT 30 - HC 8 - 70 8 28 44.5 70 30 27 M6x1.0
WB100HMC CCT40 AD/B - HMC 6 - 120 6 20 49.5 120 70 27 M5X0.8 WD104 CBT 30 - HC 10 - 75 10 30 44.5 75 31 32 M8x1.0
WB102HMC CCT40 AD/B - HMC 6 - 150 6 20 49.5 150 100 27 M5X0.8 WD106 30 CBT 30 - HC 12 - 85 12 32 45 85 45 37 M10x1.0
WB104HMC CCT40 AD/B - HMC 8 - 120 8 22 49.5 120 70 27 M6X1.0 WD108 CBT 30 - HC 14 - 85 14 34 45 85 45 37 M10x1.0
WB106HMC CCT40 AD/B - HMC 8 - 150 8 22 49.5 150 100 27 M6X1.0 WD110 CBT 30 - HC 16 - 90 16 38 45 90 50 42 M10x1.0
WB108HMC CCT40 AD/B - HMC 10 - 120 10 24 49.5 120 70 32 M8X1.0 WD112 CBT 30 - HC 18 - 90 18 40 45 90 50 42 M10x1.0
WB110HMC 40 CCT40 AD/B - HMC 10 - 150 10 24 49.5 150 100 32 M8X1.0 WD114 CBT 30 - HC 20 - 90 20 42 45 90 50 42 M6x1.0
WB112HMC CCT40 AD/B - HMC 12 - 120 12 25 49.5 120 70 37 M10X1.0 WE100 CBT 40 - HC 6 - 90 6 26 44.5 90 43 27 M5x0.8
WB114HMC CCT40 AD/B - HMC 12 - 150 12 25 49.5 150 100 37 M10X1.0 WE102 CBT 40 - HC 8 - 90 8 28 44.5 90 44.5 27 M6x1.0
WB116HMC CCT40 AD/B - HMC 16 - 120 16 32 49.5 120 70 42 M12X1.0 WE104 CBT 40 - HC 10 - 90 10 30 44.5 90 44.5 32 M8x1.0
WB118HMC CCT40 AD/B - HMC 16 - 150 16 32 49.5 150 100 42 M12X1.0 WE106 CBT 40 - HC 12 - 90 12 32 44.5 90 44.5 37 M10x1.0
WB120HMC CCT40 AD/B - HMC 20 - 120 20 34 49.5 120 70 42 M16X1.0 WE108 CBT 40 - HC 14 - 90 14 34 44.5 90 44.5 37 M10x1.0
WB122HMC CCT40 AD/B - HMC 20 - 150 20 34 49.5 150 100 42 M16X1.0 WE110 40 CBT 40 - HC 16 - 90 16 38 44.5 90 47.5 42 M12x1.0
WC100HMC CCT50 AD/B - HMC 6 - 150 6 20 44.5 150 100 27 M5X0.8 WE112 CBT 40 - HC 18 - 90 18 40 44.5 90 47.5 42 M12x1.0
WC102HMC CCT50 AD/B - HMC 8 - 150 8 22 44.5 150 100 27 M6X1.0 WE114 CBT 40 - HC 20 - 90 20 42 44.5 90 47.5 42 M16x1.0
WC104HMC 50 CCT50 AD/B - HMC 10 - 150 10 24 44.5 150 100 32 M8X1.0 WE116 CBT 40 - HC 25 - 100 25 50 60 100 47.5 48 M16x1.0
WC106HMC CCT50 AD/B - HMC 12 - 150 12 25 44.5 150 100 37 M10X1.0
WC108HMC CCT50 AD/B - HMC 16 - 150 16 32 44.5 150 100 42 M12X1.0 WE118 CBT 40 - HC 32 - 105 32 60 - 105 - 55 M16x1.0
WC110HMC CCT50 AD/B - HMC 20 - 150 20 34 44.5 150 100 42 M16X1.0 * Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
1322 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1323

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




DUAL CONTACT HYDRAULIC CHUCK (Power E Hydro) CBT DUAL CONTACT HYDRAULIC CHUCK (For MOULD) CBT
L2
L2
FIG.1
L2
G
d1 D1 D2 D3
d1 D1 D2 D3 3°
TAPER No. d1 D1 D2
TAPER No. L
L TAPER No. L1
L
FIG.2
L2
L2

Taper Run-Out Coolant
d1 D1 D2 CBT Accuracy G Value RPM (at 3D) System
d1 D1 D2 AT3 2.5 25,000 ≤0.00012" AD
TAPER No.
TAPER No. L CBT (BT DUAL CONTACT) Unit : inch
L
Taper G Value RPM Run-Out Coolant
Accuracy (at 3D) System
CBT
AT3 2.5 25,000 ≤0.00012" AD
CBT (BT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WD030PE 30 CBT 30 - HC 3/4P - 3.543 0.75 1.496 1.653 1.751 3.543 1.889 M8x1.0mm 1
WE030PE 40 CBT 40 - HC 3/4P - 2.854 0.75 1.496 1.938 - 2.854 1.889 M8x1.0mm 2

Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WD112PE 30 CBT 30 - HC 12P - 69 12 32 42 44.5 69 41 M8x1.0 1
WD120PE CBT 30 - HC 20P - 90 20 38 42 44.5 90 48 M8x1.0 1
WE112PE CBT 40 - HC 12P - 58 12 32 42 - 58 41 M8x1.0 2 Unit : mm
WE120PE 40 CBT 40 - HC 20P - 72.5 20 38 49.25 - 72.5 48 M8x1.0 2 EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G

* High Clamping Torque Power version WE100HMC CBT 40 - HMC 6 - 120 6 20 44.5 120 70 27 M5x0.8
(Please refer to page 1420, Technical Information) WE102HMC CBT 40 - HMC 6 - 150 6 20 44.5 150 100 27 M5x0.8
* Applicable for milling(roughing and finishing) WE104HMC CBT 40 - HMC 8 - 120 8 22 44.5 120 70 27 M6x1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
WE106HMC CBT 40 - HMC 8 - 150 8 22 44.5 150 100 27 M6x1.0
WE108HMC CBT 40 - HMC 10 - 120 10 24 44.5 120 70 32 M8x1.0
WE110HMC 40 CBT 40 - HMC 10 - 150 10 24 44.5 150 100 32 M8x1.0
WE112HMC CBT 40 - HMC 12 - 120 12 25 44.5 120 70 37 M10x1.0
WE114HMC CBT 40 - HMC 12 - 150 12 25 44.5 150 100 37 M10x1.0
WE116HMC CBT 40 - HMC 16 - 120 16 32 44.5 120 70 42 M12x1.0
WE118HMC CBT 40 - HMC 16 - 150 16 32 44.5 150 100 42 M12x1.0
WE120HMC CBT 40 - HMC 20 - 120 20 34 43.8 120 - 42 M16x1.0
WE122HMC CBT 40 - HMC 20 - 150 20 34 46.9 150 - 42 M16x1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.









1324 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1325

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




DUAL CONTACT HYDRAULIC CHUCK (Power E Hydro) CBT DUAL CONTACT HYDRAULIC CHUCK (For MOULD) CBT
L2
L2
FIG.1
L2
G
d1 D1 D2 D3
d1 D1 D2 D3 3°
TAPER No. d1 D1 D2
TAPER No. L
L TAPER No. L1
L
FIG.2
L2
L2

Taper Run-Out Coolant
d1 D1 D2 CBT Accuracy G Value RPM (at 3D) System
d1 D1 D2 AT3 2.5 25,000 ≤0.00012" AD
TAPER No.
TAPER No. L CBT (BT DUAL CONTACT) Unit : inch
L
Taper G Value RPM Run-Out Coolant
Accuracy (at 3D) System
CBT
AT3 2.5 25,000 ≤0.00012" AD
CBT (BT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WD030PE 30 CBT 30 - HC 3/4P - 3.543 0.75 1.496 1.653 1.751 3.543 1.889 M8x1.0mm 1
WE030PE 40 CBT 40 - HC 3/4P - 2.854 0.75 1.496 1.938 - 2.854 1.889 M8x1.0mm 2

Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WD112PE 30 CBT 30 - HC 12P - 69 12 32 42 44.5 69 41 M8x1.0 1
WD120PE CBT 30 - HC 20P - 90 20 38 42 44.5 90 48 M8x1.0 1
WE112PE CBT 40 - HC 12P - 58 12 32 42 - 58 41 M8x1.0 2 Unit : mm
WE120PE 40 CBT 40 - HC 20P - 72.5 20 38 49.25 - 72.5 48 M8x1.0 2 EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G

* High Clamping Torque Power version WE100HMC CBT 40 - HMC 6 - 120 6 20 44.5 120 70 27 M5x0.8
(Please refer to page 1420, Technical Information) WE102HMC CBT 40 - HMC 6 - 150 6 20 44.5 150 100 27 M5x0.8
* Applicable for milling(roughing and finishing) WE104HMC CBT 40 - HMC 8 - 120 8 22 44.5 120 70 27 M6x1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.
WE106HMC CBT 40 - HMC 8 - 150 8 22 44.5 150 100 27 M6x1.0
WE108HMC CBT 40 - HMC 10 - 120 10 24 44.5 120 70 32 M8x1.0
WE110HMC 40 CBT 40 - HMC 10 - 150 10 24 44.5 150 100 32 M8x1.0
WE112HMC CBT 40 - HMC 12 - 120 12 25 44.5 120 70 37 M10x1.0
WE114HMC CBT 40 - HMC 12 - 150 12 25 44.5 150 100 37 M10x1.0
WE116HMC CBT 40 - HMC 16 - 120 16 32 44.5 120 70 42 M12x1.0
WE118HMC CBT 40 - HMC 16 - 150 16 32 44.5 150 100 42 M12x1.0
WE120HMC CBT 40 - HMC 20 - 120 20 34 43.8 120 - 42 M16x1.0
WE122HMC CBT 40 - HMC 20 - 150 20 34 46.9 150 - 42 M16x1.0
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.









1324 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1325

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


HSK HSK
DUAL CONTACT HYDRAULIC CHUCK (SLIM) HYDRAULIC CHUCK (Power E Hydro)

FIG.1 L2
G L2




d1 D1 D2
d1 D1 D2

TAPER No.
L1
TAPER No. L
L
FIG.2

Taper G Value RPM Run-Out Coolant
DIN 69893 Accuracy (at 3D) System d1 D1 D2 D3
- HSK - 2.5 25,000 ≤0.00012" AD

TAPER No.
DIN 69893/ISO 12164-1 HSK FROM A Unit : inch L
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
Taper G Value RPM Run-Out Coolant
WQ020 HSK 63A - HC 1/4 - 2.76 0.250 1.024 1.969 2.756 0.945 1.063 M5x0.8mm DIN 69893 Accuracy (at 3D) System
WQ022 HSK 63A - HC 3/8 - 3.15 0.375 1.181 1.969 3.150 1.378 1.260 M8x1.0mm - HSK - 2.5 25,000 ≤0.00012" AD
WQ024 HSK 63A - HC 1/2 - 3.35 0.500 1.260 1.969 3.346 1.575 1.457 M10x1.0mm
WQ026 63A HSK 63A - HC 3/4 - 3.54 0.750 1.654 1.969 3.543 1.890 1.654 M16x1.0mm DIN 69893/ISO 12164-1-HSK FORM A Unit : inch
WQ028 HSK 63A - HC 1" - 4.72 1.000 2.244 2.480 4.724 2.323 1.890 M16x1.0mm EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WQ030 HSK 63A - HC 1 1/4 - 4.92 1.250 2.520 2.953 4.921 2.480 2.165 M16x1.0mm
WR020 HSK 100A - HC 1/4 - 2.95 0.250 1.024 1.969 2.953 1.024 1.063 M5x0.8mm WQ002PE 63A HSK 63A - HC 3/4P - 3.149 0.75 1.496 2.066 - 3.149 1.889 M8x1.0mm 1
WR022 HSK 100A - HC 3/8 - 2.95 0.375 1.181 1.969 3.543 1.654 1.260 M8x1.0mm WQ003PE HSK 63A - HC 3/4P - 5.118 0.75 1.496 2.066 - 5.118 1.889 M8x1.0mm 1
WR024 HSK 100A - HC 1/2 - 3.74 0.500 1.260 1.969 3.740 1.850 1.457 M10x1.0mm WR002PE 100A HSK 100A - HC 1 1/4P - 3.937 1.25 2.303 2.834 - 3.937 2.244 M8x1.0mm 1
WR026 100A HSK 100A - HC 3/4 - 4.13 0.750 1.654 1.969 4.134 2.323 1.654 M16x1.0mm
WR028 HSK 100A - HC 1" - 4.33 1.000 2.244 2.480 4.331 2.441 1.890 M16x1.0mm Unit : mm
WR032 HSK 100A - HC 1 1/4 - 4.33 1.250 2.520 2.953 4.331 2.441 2.165 M16x1.0mm EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WQ100PE 63A HSK 63A - HC 12P - 80 12 32 42 52.5 80 41 M8x1.0 2
WQ102PE HSK 63A - HC 20P - 80 20 38 52.5 - 80 48 M8x1.0 1
WR100PE 100A HSK 100A - HC 20P - 90 20 38 52.5 - 90 48 M8x1.0 1
WR102PE HSK 100A - HC 32P - 100 32 58.5 72 - 100 57 M8x1.0 1
* High Clamping Torque Power version
(Please refer to page 1420, Technical Information)
* Applicable for milling(roughing and finishing)
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.






















1326 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1327

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


HSK HSK
DUAL CONTACT HYDRAULIC CHUCK (SLIM) HYDRAULIC CHUCK (Power E Hydro)

FIG.1 L2
G L2




d1 D1 D2
d1 D1 D2

TAPER No.
L1
TAPER No. L
L
FIG.2

Taper G Value RPM Run-Out Coolant
DIN 69893 Accuracy (at 3D) System d1 D1 D2 D3
- HSK - 2.5 25,000 ≤0.00012" AD

TAPER No.
DIN 69893/ISO 12164-1 HSK FROM A Unit : inch L
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G
Taper G Value RPM Run-Out Coolant
WQ020 HSK 63A - HC 1/4 - 2.76 0.250 1.024 1.969 2.756 0.945 1.063 M5x0.8mm DIN 69893 Accuracy (at 3D) System
WQ022 HSK 63A - HC 3/8 - 3.15 0.375 1.181 1.969 3.150 1.378 1.260 M8x1.0mm - HSK - 2.5 25,000 ≤0.00012" AD
WQ024 HSK 63A - HC 1/2 - 3.35 0.500 1.260 1.969 3.346 1.575 1.457 M10x1.0mm
WQ026 63A HSK 63A - HC 3/4 - 3.54 0.750 1.654 1.969 3.543 1.890 1.654 M16x1.0mm DIN 69893/ISO 12164-1-HSK FORM A Unit : inch
WQ028 HSK 63A - HC 1" - 4.72 1.000 2.244 2.480 4.724 2.323 1.890 M16x1.0mm EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
WQ030 HSK 63A - HC 1 1/4 - 4.92 1.250 2.520 2.953 4.921 2.480 2.165 M16x1.0mm
WR020 HSK 100A - HC 1/4 - 2.95 0.250 1.024 1.969 2.953 1.024 1.063 M5x0.8mm WQ002PE 63A HSK 63A - HC 3/4P - 3.149 0.75 1.496 2.066 - 3.149 1.889 M8x1.0mm 1
WR022 HSK 100A - HC 3/8 - 2.95 0.375 1.181 1.969 3.543 1.654 1.260 M8x1.0mm WQ003PE HSK 63A - HC 3/4P - 5.118 0.75 1.496 2.066 - 5.118 1.889 M8x1.0mm 1
WR024 HSK 100A - HC 1/2 - 3.74 0.500 1.260 1.969 3.740 1.850 1.457 M10x1.0mm WR002PE 100A HSK 100A - HC 1 1/4P - 3.937 1.25 2.303 2.834 - 3.937 2.244 M8x1.0mm 1
WR026 100A HSK 100A - HC 3/4 - 4.13 0.750 1.654 1.969 4.134 2.323 1.654 M16x1.0mm
WR028 HSK 100A - HC 1" - 4.33 1.000 2.244 2.480 4.331 2.441 1.890 M16x1.0mm Unit : mm
WR032 HSK 100A - HC 1 1/4 - 4.33 1.250 2.520 2.953 4.331 2.441 2.165 M16x1.0mm EDP No. TAPER No. MODEL No. d1 D1 D2 D3 L L2 G FIG.
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WQ100PE 63A HSK 63A - HC 12P - 80 12 32 42 52.5 80 41 M8x1.0 2
WQ102PE HSK 63A - HC 20P - 80 20 38 52.5 - 80 48 M8x1.0 1
WR100PE 100A HSK 100A - HC 20P - 90 20 38 52.5 - 90 48 M8x1.0 1
WR102PE HSK 100A - HC 32P - 100 32 58.5 72 - 100 57 M8x1.0 1
* High Clamping Torque Power version
(Please refer to page 1420, Technical Information)
* Applicable for milling(roughing and finishing)
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.






















1326 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1327

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


HSK HSK
DUAL CONTACT HYDRAULIC CHUCK (SHORT & RIGID) DUAL CONTACT HYDRAULIC CHUCK (RADIAL TOOL LENGTH PRE-SETTING TYPE)


G L2 Radial Length
Adjustment L2




d1 D1 D2
d1 D1 D2


L1
TAPER No.
L
TAPER No. L
Taper Run-Out Coolant Taper Run-Out Coolant
DIN 69893 Accuracy G Value RPM (at 3D) System DIN 69893 Accuracy G Value RPM (at 3D) System
- HSK - 2.5 25,000 ≤0.00012" AD - HSK - 2.5 25,000 ≤0.00012" AD

DIN 69893/ISO 12164-1-HSK FORM A Unit : mm DIN 69893/ISO 12164-1-HSK FORM A Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2
WQ100SNR HSK 63A - HC 12S - 80 12 32 42 80 37 M8x1.0 WQ100HCR HSK 63A - HCR 6 - 85 6 26 50 85 33 27
WQ102SNR 63A HSK 63A - HC 20S - 80 20 38 52.5 80 42 M8x1.0 WQ102HCR HSK 63A - HCR 8 - 85 8 28 50 85 33 27
WR100SNR HSK 100A - HC 12S - 85 12 32 42 85 35 M8x1.0 WQ104HCR HSK 63A - HCR 10 - 85 10 30 50 85 38 32
WR102SNR 100A HSK 100A - HC 20S - 90 20 38 52.5 90 42 M8x1.0 WQ106HCR HSK 63A - HCR 12 - 95 12 32 50 95 40 37
WQ108HCR HSK 63A - HCR 14 - 95 14 34 50 95 46 37
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WQ110HCR 63A HSK 63A - HCR 16 - 95 16 38 50 95 51 42
WQ112HCR HSK 63A - HCR 18 - 95 18 40 50 95 52 42
WQ114HCR HSK 63A - HCR 20 - 100 20 42 50 100 51 42
WQ116HCR HSK 63A - HCR 25 - 120 25 57 63 120 54.5 48
WQ118HCR HSK 63A - HCR 32 - 125 32 64 75 125 57.5 55
WR100HCR HSK 100A - HCR 6 - 90 6 26 63 90 33 27
WR102HCR HSK 100A - HCR 8 - 90 8 28 63 90 33 27
WR104HCR HSK 100A - HCR 10 - 95 10 30 63 95 36 32
WR106HCR HSK 100A - HCR 12 - 100 12 32 63 100 40 37
WR108HCR HSK 100A - HCR 14 - 100 14 34 63 100 41 37
WR110HCR 100A HSK 100A - HCR 16 - 105 16 38 63 105 46 42
WR112HCR HSK 100A - HCR 18 - 105 18 40 63 105 46 42
WR114HCR HSK 100A - HCR 20 - 105 20 42 75 105 51 42
WR116HCR HSK 100A - HCR 25 - 115 25 57 75 115 55.5 48
WR118HCR HSK 100A - HCR 32 - 120 32 64 75 120 63.5 55
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.





















1328 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1329

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


HSK HSK
DUAL CONTACT HYDRAULIC CHUCK (SHORT & RIGID) DUAL CONTACT HYDRAULIC CHUCK (RADIAL TOOL LENGTH PRE-SETTING TYPE)


G L2 Radial Length
Adjustment L2




d1 D1 D2
d1 D1 D2


L1
TAPER No.
L
TAPER No. L
Taper Run-Out Coolant Taper Run-Out Coolant
DIN 69893 Accuracy G Value RPM (at 3D) System DIN 69893 Accuracy G Value RPM (at 3D) System
- HSK - 2.5 25,000 ≤0.00012" AD - HSK - 2.5 25,000 ≤0.00012" AD

DIN 69893/ISO 12164-1-HSK FORM A Unit : mm DIN 69893/ISO 12164-1-HSK FORM A Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2
WQ100SNR HSK 63A - HC 12S - 80 12 32 42 80 37 M8x1.0 WQ100HCR HSK 63A - HCR 6 - 85 6 26 50 85 33 27
WQ102SNR 63A HSK 63A - HC 20S - 80 20 38 52.5 80 42 M8x1.0 WQ102HCR HSK 63A - HCR 8 - 85 8 28 50 85 33 27
WR100SNR HSK 100A - HC 12S - 85 12 32 42 85 35 M8x1.0 WQ104HCR HSK 63A - HCR 10 - 85 10 30 50 85 38 32
WR102SNR 100A HSK 100A - HC 20S - 90 20 38 52.5 90 42 M8x1.0 WQ106HCR HSK 63A - HCR 12 - 95 12 32 50 95 40 37
WQ108HCR HSK 63A - HCR 14 - 95 14 34 50 95 46 37
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338. WQ110HCR 63A HSK 63A - HCR 16 - 95 16 38 50 95 51 42
WQ112HCR HSK 63A - HCR 18 - 95 18 40 50 95 52 42
WQ114HCR HSK 63A - HCR 20 - 100 20 42 50 100 51 42
WQ116HCR HSK 63A - HCR 25 - 120 25 57 63 120 54.5 48
WQ118HCR HSK 63A - HCR 32 - 125 32 64 75 125 57.5 55
WR100HCR HSK 100A - HCR 6 - 90 6 26 63 90 33 27
WR102HCR HSK 100A - HCR 8 - 90 8 28 63 90 33 27
WR104HCR HSK 100A - HCR 10 - 95 10 30 63 95 36 32
WR106HCR HSK 100A - HCR 12 - 100 12 32 63 100 40 37
WR108HCR HSK 100A - HCR 14 - 100 14 34 63 100 41 37
WR110HCR 100A HSK 100A - HCR 16 - 105 16 38 63 105 46 42
WR112HCR HSK 100A - HCR 18 - 105 18 40 63 105 46 42
WR114HCR HSK 100A - HCR 20 - 105 20 42 75 105 51 42
WR116HCR HSK 100A - HCR 25 - 115 25 57 75 115 55.5 48
WR118HCR HSK 100A - HCR 32 - 120 32 64 75 120 63.5 55
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.





















1328 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1329

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


HSK
DUAL CONTACT HYDRAULIC CHUCK (For MOULD) HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : OPEN TYPE)


G L2
3° D1 d D2

d1 D1 D2
L2
L
L1
TAPER No. L





Taper Run-Out Coolant
DIN 69893 Accuracy G Value RPM (at 3D) System Hydraulic Chuck collet
-HSK - 2.5 25,000 ≤0.00012" AD

DIN 69893/ISO 12164-1-HSK FORM A Unit : inch METRIC / INCH Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G EDP No. TYPE d D1 D2 L L2
WQ020HMC HSK 63A - HMC 1/4 - 5.71 0.250 0.787 1.969 5.709 3.543 1.063 M5x0.8mm 412108 1/8" 0.125 0.472 0.748 1.850 0.079
WQ022HMC HSK 63A - HMC 5/16 - 5.71 0.313 0.866 1.969 5.709 3.543 1.063 M6x1.0mm 412316 HK12 3/16" 0.188 0.472 0.748 1.850 0.079
WQ024HMC 63A HSK 63A - HMC 3/8 - 5.71 0.375 0.945 1.969 5.709 3.543 1.260 M8x1.0mm 412104 1/4" 0.250 0.472 0.748 1.850 0.079
WQ026HMC HSK 63A - HMC 1/2 - 5.71 0.500 1.024 1.969 5.709 3.543 1.457 M10x1.0mm 412516 5/16" 0.313 0.472 0.748 1.850 0.079
WQ028HMC HSK 63A - HMC 5/8 - 5.71 0.625 1.260 1.969 5.709 3.543 1.654 M12x1.0mm 420108 1/8" 0.125 0.787 1.063 2.067 0.079
WQ030HMC HSK 63A - HMC 3/4 - 5.71 0.750 1.339 1.969 5.709 3.543 1.654 M16x1.0mm 420316 3/16" 0.188 0.787 1.063 2.067 0.079
WR100HMC HSK 100A - HMC 1/4 - 5.71 0.250 0.787 1.969 5.709 3.543 1.063 M5x0.8mm 420104 1/4" 0.250 0.787 1.063 2.067 0.079
WR102HMC HSK 100A - HMC 5/16 - 5.71 0.313 0.866 1.969 5.709 3.543 1.063 M6x1.0mm 420516 HK20 5/16" 0.313 0.787 1.063 2.067 0.079
WR104HMC HSK 100A - HMC 3/8 - 5.71 0.375 0.945 1.969 5.709 3.543 1.260 M8x1.0mm 420308 3/8" 0.375 0.787 1.063 2.067 0.079
WR106HMC 100A HSK 100A - HMC 1/2 - 5.71 0.500 1.024 1.969 5.709 3.543 1.457 M10x1.0mm 420102 1/2" 0.500 0.787 1.063 2.067 0.079
WR108HMC HSK 100A - HMC 5/8 - 5.71 0.625 1.260 1.969 5.709 3.543 1.654 M12x1.0mm 420508 5/8" 0.625 0.787 1.063 2.067 0.079
WR110HMC HSK 100A - HMC 3/4 - 5.71 0.750 1.339 1.969 5.709 3.543 1.654 M16x1.0mm 432108 1/8" 0.125 1.260 1.535 2.500 0.118
432316 3/16" 0.188 1.260 1.535 2.500 0.118
432104 1/4" 0.250 1.260 1.535 2.500 0.118
Unit : mm 432516 5/16" 0.313 1.260 1.535 2.500 0.118
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G 432308 HK32 3/8" 0.375 1.260 1.535 2.500 0.118
WQ100HMC HSK 63A - HMC 6 - 145 6 20 50 145 90 27 M5x0.8 432102 1/2" 0.500 1.260 1.535 2.500 0.118
WQ102HMC HSK 63A - HMC 8 - 145 8 22 50 145 90 27 M6x1.0 432508 5/8" 0.625 1.260 1.535 2.500 0.118
WQ104HMC HSK 63A - HMC 10 - 145 10 24 50 145 90 32 M8x1.0 432304 3/4" 0.750 1.260 1.535 2.500 0.118
WQ106HMC 63A HSK 63A - HMC 12 - 145 12 25 50 145 90 37 M10x1.0 432100 1 1.000 1.260 1.535 2.500 0.118
WQ108HMC HSK 63A - HMC 16 - 145 16 32 50 145 90 42 M12x1.0 * Other special sizes of Hydraulic Chuck collets can be supplied on request.
WQ110HMC HSK 63A - HMC 20 - 145 20 34 50 145 90 42 M16x1.0
WR200HMC HSK 100A - HMC 6 - 150 6 20 50 150 90 27 M5x0.8
WR202HMC HSK 100A - HMC 8 - 150 8 22 50 150 90 27 M6x1.0
WR204HMC 100A HSK 100A - HMC10 - 150 10 24 50 150 90 32 M8x1.0
WR206HMC HSK 100A - HMC12 - 150 12 25 50 150 90 37 M10x1.0 Feature Hydraulic Chuck collet(reduction sleeve) is cut into trisection by high precision cutting to
WR208HMC HSK 100A - HMC16 - 150 16 32 50 150 90 42 M12x1.0 guarantee precise I.D and strong clamping power.
WR210HMC HSK 100A - HMC20 - 150 20 34 50 150 90 42 M16x1.0 Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.









1330 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1331

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS


HSK
DUAL CONTACT HYDRAULIC CHUCK (For MOULD) HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : OPEN TYPE)


G L2
3° D1 d D2

d1 D1 D2
L2
L
L1
TAPER No. L





Taper Run-Out Coolant
DIN 69893 Accuracy G Value RPM (at 3D) System Hydraulic Chuck collet
-HSK - 2.5 25,000 ≤0.00012" AD

DIN 69893/ISO 12164-1-HSK FORM A Unit : inch METRIC / INCH Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G EDP No. TYPE d D1 D2 L L2
WQ020HMC HSK 63A - HMC 1/4 - 5.71 0.250 0.787 1.969 5.709 3.543 1.063 M5x0.8mm 412108 1/8" 0.125 0.472 0.748 1.850 0.079
WQ022HMC HSK 63A - HMC 5/16 - 5.71 0.313 0.866 1.969 5.709 3.543 1.063 M6x1.0mm 412316 HK12 3/16" 0.188 0.472 0.748 1.850 0.079
WQ024HMC 63A HSK 63A - HMC 3/8 - 5.71 0.375 0.945 1.969 5.709 3.543 1.260 M8x1.0mm 412104 1/4" 0.250 0.472 0.748 1.850 0.079
WQ026HMC HSK 63A - HMC 1/2 - 5.71 0.500 1.024 1.969 5.709 3.543 1.457 M10x1.0mm 412516 5/16" 0.313 0.472 0.748 1.850 0.079
WQ028HMC HSK 63A - HMC 5/8 - 5.71 0.625 1.260 1.969 5.709 3.543 1.654 M12x1.0mm 420108 1/8" 0.125 0.787 1.063 2.067 0.079
WQ030HMC HSK 63A - HMC 3/4 - 5.71 0.750 1.339 1.969 5.709 3.543 1.654 M16x1.0mm 420316 3/16" 0.188 0.787 1.063 2.067 0.079
WR100HMC HSK 100A - HMC 1/4 - 5.71 0.250 0.787 1.969 5.709 3.543 1.063 M5x0.8mm 420104 1/4" 0.250 0.787 1.063 2.067 0.079
WR102HMC HSK 100A - HMC 5/16 - 5.71 0.313 0.866 1.969 5.709 3.543 1.063 M6x1.0mm 420516 HK20 5/16" 0.313 0.787 1.063 2.067 0.079
WR104HMC HSK 100A - HMC 3/8 - 5.71 0.375 0.945 1.969 5.709 3.543 1.260 M8x1.0mm 420308 3/8" 0.375 0.787 1.063 2.067 0.079
WR106HMC 100A HSK 100A - HMC 1/2 - 5.71 0.500 1.024 1.969 5.709 3.543 1.457 M10x1.0mm 420102 1/2" 0.500 0.787 1.063 2.067 0.079
WR108HMC HSK 100A - HMC 5/8 - 5.71 0.625 1.260 1.969 5.709 3.543 1.654 M12x1.0mm 420508 5/8" 0.625 0.787 1.063 2.067 0.079
WR110HMC HSK 100A - HMC 3/4 - 5.71 0.750 1.339 1.969 5.709 3.543 1.654 M16x1.0mm 432108 1/8" 0.125 1.260 1.535 2.500 0.118
432316 3/16" 0.188 1.260 1.535 2.500 0.118
432104 1/4" 0.250 1.260 1.535 2.500 0.118
Unit : mm 432516 5/16" 0.313 1.260 1.535 2.500 0.118
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 L2 G 432308 HK32 3/8" 0.375 1.260 1.535 2.500 0.118
WQ100HMC HSK 63A - HMC 6 - 145 6 20 50 145 90 27 M5x0.8 432102 1/2" 0.500 1.260 1.535 2.500 0.118
WQ102HMC HSK 63A - HMC 8 - 145 8 22 50 145 90 27 M6x1.0 432508 5/8" 0.625 1.260 1.535 2.500 0.118
WQ104HMC HSK 63A - HMC 10 - 145 10 24 50 145 90 32 M8x1.0 432304 3/4" 0.750 1.260 1.535 2.500 0.118
WQ106HMC 63A HSK 63A - HMC 12 - 145 12 25 50 145 90 37 M10x1.0 432100 1 1.000 1.260 1.535 2.500 0.118
WQ108HMC HSK 63A - HMC 16 - 145 16 32 50 145 90 42 M12x1.0 * Other special sizes of Hydraulic Chuck collets can be supplied on request.
WQ110HMC HSK 63A - HMC 20 - 145 20 34 50 145 90 42 M16x1.0
WR200HMC HSK 100A - HMC 6 - 150 6 20 50 150 90 27 M5x0.8
WR202HMC HSK 100A - HMC 8 - 150 8 22 50 150 90 27 M6x1.0
WR204HMC 100A HSK 100A - HMC10 - 150 10 24 50 150 90 32 M8x1.0
WR206HMC HSK 100A - HMC12 - 150 12 25 50 150 90 37 M10x1.0 Feature Hydraulic Chuck collet(reduction sleeve) is cut into trisection by high precision cutting to
WR208HMC HSK 100A - HMC16 - 150 16 32 50 150 90 42 M12x1.0 guarantee precise I.D and strong clamping power.
WR210HMC HSK 100A - HMC20 - 150 20 34 50 150 90 42 M16x1.0 Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.
* Applicable Hydraulic Chuck collets(reduction sleeves) on page 1331~1338.









1330 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1331

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE) HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE)




D1 d D2


L2
L









Hydraulic Chuck collet Hydraulic Chuck collet


METRIC / INCH Unit : inch INCH / INCH Unit : inch
EDP No. TYPE d D1 D2 L L2 EDP No. TYPE d D1 D2 L L2
512108 1/8" 0.125 0.472 0.748 1.850 0.079 612108 1/8" 0.125 0.500 0.748 1.850 0.079
512316 HS12 3/16" 0.188 0.472 0.748 1.850 0.079 612316 HK1/2" 3/16" 0.188 0.500 0.748 1.850 0.079
512104 1/4" 0.250 0.472 0.748 1.850 0.079 612104 1/4" 0.250 0.500 0.748 1.850 0.079
512516 5/16" 0.313 0.472 0.748 1.850 0.079 612516 5/16" 0.313 0.500 0.748 1.850 0.079
520108 1/8" 0.125 0.787 1.063 2.067 0.079 625108 1/8" 0.125 0.750 1.063 2.067 0.079
520316 3/16" 0.188 0.787 1.063 2.067 0.079 625316 3/16" 0.188 0.750 1.063 2.067 0.079
520104 1/4" 0.250 0.787 1.063 2.067 0.079 625104 1/4" 0.250 0.750 1.063 2.067 0.079
520516 HS20 5/16" 0.313 0.787 1.063 2.067 0.079 625516 HK3/4" 5/16" 0.313 0.750 1.063 2.067 0.079
520308 3/8" 0.375 0.787 1.063 2.067 0.079 625308 3/8" 0.375 0.750 1.063 2.067 0.079
520102 1/2" 0.500 0.787 1.063 2.067 0.079 625102 1/2" 0.500 0.750 1.063 2.067 0.079
520508 5/8" 0.625 0.787 1.063 2.067 0.079 625508 5/8" 0.625 0.750 1.063 2.067 0.079
532108 1/8" 0.125 1.260 1.535 2.500 0.118 632108 1/8" 0.125 1.250 1.535 2.500 0.118
532316 3/16" 0.188 1.260 1.535 2.500 0.118 632316 3/16" 0.188 1.250 1.535 2.500 0.118
532104 1/4" 0.250 1.260 1.535 2.500 0.118 632104 1/4" 0.250 1.250 1.535 2.500 0.118
532516 5/16" 0.313 1.260 1.535 2.500 0.118 632516 5/16" 0.313 1.250 1.535 2.500 0.118
532308 HS32 3/8" 0.375 1.260 1.535 2.500 0.118 632308 HK1 1/4" 3/8" 0.375 1.250 1.535 2.500 0.118
532102 1/2" 0.500 1.260 1.535 2.500 0.118 632102 1/2" 0.500 1.250 1.535 2.500 0.118
532508 5/8" 0.625 1.260 1.535 2.500 0.118 632508 5/8" 0.625 1.250 1.535 2.500 0.118
532304 3/4" 0.750 1.260 1.535 2.500 0.118 632304 3/4" 0.750 1.250 1.535 2.500 0.118
532100 1 1.000 1.260 1.535 2.500 0.118 632100 1 1.000 1.250 1.535 2.500 0.118

* Other special sizes of Hydraulic Chuck collets can be supplied on request. * Other special sizes of Hydraulic Chuck collets can be supplied on request.




Feature The wall of Hydraulic Chuck collet(reduction sleeve) is cut by high precision wire-cutting to Feature Hydraulic Chuck collet(reduction sleeve) is cut into trisection by high precision cutting to
guarantee precise I.D and strong clamping power. guarantee precise I.D and strong clamping power.
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck. Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.











1332 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1333

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE) HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE)




D1 d D2


L2
L









Hydraulic Chuck collet Hydraulic Chuck collet


METRIC / INCH Unit : inch INCH / INCH Unit : inch
EDP No. TYPE d D1 D2 L L2 EDP No. TYPE d D1 D2 L L2
512108 1/8" 0.125 0.472 0.748 1.850 0.079 612108 1/8" 0.125 0.500 0.748 1.850 0.079
512316 HS12 3/16" 0.188 0.472 0.748 1.850 0.079 612316 HK1/2" 3/16" 0.188 0.500 0.748 1.850 0.079
512104 1/4" 0.250 0.472 0.748 1.850 0.079 612104 1/4" 0.250 0.500 0.748 1.850 0.079
512516 5/16" 0.313 0.472 0.748 1.850 0.079 612516 5/16" 0.313 0.500 0.748 1.850 0.079
520108 1/8" 0.125 0.787 1.063 2.067 0.079 625108 1/8" 0.125 0.750 1.063 2.067 0.079
520316 3/16" 0.188 0.787 1.063 2.067 0.079 625316 3/16" 0.188 0.750 1.063 2.067 0.079
520104 1/4" 0.250 0.787 1.063 2.067 0.079 625104 1/4" 0.250 0.750 1.063 2.067 0.079
520516 HS20 5/16" 0.313 0.787 1.063 2.067 0.079 625516 HK3/4" 5/16" 0.313 0.750 1.063 2.067 0.079
520308 3/8" 0.375 0.787 1.063 2.067 0.079 625308 3/8" 0.375 0.750 1.063 2.067 0.079
520102 1/2" 0.500 0.787 1.063 2.067 0.079 625102 1/2" 0.500 0.750 1.063 2.067 0.079
520508 5/8" 0.625 0.787 1.063 2.067 0.079 625508 5/8" 0.625 0.750 1.063 2.067 0.079
532108 1/8" 0.125 1.260 1.535 2.500 0.118 632108 1/8" 0.125 1.250 1.535 2.500 0.118
532316 3/16" 0.188 1.260 1.535 2.500 0.118 632316 3/16" 0.188 1.250 1.535 2.500 0.118
532104 1/4" 0.250 1.260 1.535 2.500 0.118 632104 1/4" 0.250 1.250 1.535 2.500 0.118
532516 5/16" 0.313 1.260 1.535 2.500 0.118 632516 5/16" 0.313 1.250 1.535 2.500 0.118
532308 HS32 3/8" 0.375 1.260 1.535 2.500 0.118 632308 HK1 1/4" 3/8" 0.375 1.250 1.535 2.500 0.118
532102 1/2" 0.500 1.260 1.535 2.500 0.118 632102 1/2" 0.500 1.250 1.535 2.500 0.118
532508 5/8" 0.625 1.260 1.535 2.500 0.118 632508 5/8" 0.625 1.250 1.535 2.500 0.118
532304 3/4" 0.750 1.260 1.535 2.500 0.118 632304 3/4" 0.750 1.250 1.535 2.500 0.118
532100 1 1.000 1.260 1.535 2.500 0.118 632100 1 1.000 1.250 1.535 2.500 0.118

* Other special sizes of Hydraulic Chuck collets can be supplied on request. * Other special sizes of Hydraulic Chuck collets can be supplied on request.




Feature The wall of Hydraulic Chuck collet(reduction sleeve) is cut by high precision wire-cutting to Feature Hydraulic Chuck collet(reduction sleeve) is cut into trisection by high precision cutting to
guarantee precise I.D and strong clamping power. guarantee precise I.D and strong clamping power.
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck. Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.











1332 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1333

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE) HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE)




D1 d D2


L2
L









Hydraulic Chuck collet Hydraulic Chuck collet


INCH / INCH Unit : inch METRIC / METRIC Unit : mm
EDP No. TYPE d D1 D2 L L2 EDP No. TYPE d D1 D2 L L2
712108 1/8" 0.125 0.500 0.748 1.850 0.079 812030 3 3 12 19 47 2
712316 HS1/2" 3/16" 0.188 0.500 0.748 1.850 0.079 812040 4 4 12 19 47 2
712104 1/4" 0.250 0.500 0.748 1.850 0.079 812050 HK12 5 5 12 19 47 2
712516 5/16" 0.313 0.500 0.748 1.850 0.079 812060 6 6 12 19 47 2
725108 1/8" 0.125 0.750 1.063 2.067 0.079 812070 7 7 12 19 47 2
725316 3/16" 0.188 0.750 1.063 2.067 0.079 812008 8 8 12 19 47 2
725104 1/4" 0.250 0.750 1.063 2.067 0.079 820030 3 3 20 27 52.5 2
725516 HS3/4" 5/16" 0.313 0.750 1.063 2.067 0.079 820040 4 4 20 27 52.5 2
725308 3/8" 0.375 0.750 1.063 2.067 0.079 820050 5 5 20 27 52.5 2
725102 1/2" 0.500 0.750 1.063 2.067 0.079 820060 6 6 20 27 52.5 2
52.5
27
2
820070
20
7
7
725508 5/8" 0.625 0.750 1.063 2.067 0.079 820080 8 8 20 27 52.5 2
732108 1/8" 0.125 1.250 1.535 2.500 0.118 820090 9 9 20 27 52.5 2
732316 3/16" 0.188 1.250 1.535 2.500 0.118 820100 HK20 10 10 20 27 52.5 2
732104 1/4" 0.250 1.250 1.535 2.500 0.118 820110 11 11 20 27 52.5 2
732516 5/16" 0.313 1.250 1.535 2.500 0.118 820120 12 12 20 27 52.5 2
732308 HS1 1/4" 3/8" 0.375 1.250 1.535 2.500 0.118 820130 13 13 20 27 52.5 2
732102 1/2" 0.500 1.250 1.535 2.500 0.118 820140 14 14 20 27 52.5 2
732508 5/8" 0.625 1.250 1.535 2.500 0.118 820150 15 15 20 27 52.5 2
732304 3/4" 0.750 1.250 1.535 2.500 0.118 820160 16 16 20 27 52.5 2
732100 1 1.000 1.250 1.535 2.500 0.118 832060 6 6 32 39 63.5 3
832080 8 8 32 39 63.5 3
* Other special sizes of Hydraulic Chuck collets can be supplied on request. 832100 10 10 32 39 63.5 3
832120 12 12 32 39 63.5 3
832140 HK32 14 14 32 39 63.5 3
832160 16 16 32 39 63.5 3
832180 18 18 32 39 63.5 3
Feature The wall of Hydraulic Chuck collet(reduction sleeve) is cut by high precision wire-cutting to 832200 20 20 32 39 63.5 3
guarantee precise I.D and strong clamping power.
832250 25 25 32 39 63.5 3
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.
* Other special sizes of Hydraulic Chuck collets can be supplied on request.

Feature Hydraulic Chuck collet(reduction sleeve) is cut into trisection by high precision cutting to
guarantee precise I.D and strong clamping power.
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.



1334 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1335

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE) HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE)




D1 d D2


L2
L









Hydraulic Chuck collet Hydraulic Chuck collet


INCH / INCH Unit : inch METRIC / METRIC Unit : mm
EDP No. TYPE d D1 D2 L L2 EDP No. TYPE d D1 D2 L L2
712108 1/8" 0.125 0.500 0.748 1.850 0.079 812030 3 3 12 19 47 2
712316 HS1/2" 3/16" 0.188 0.500 0.748 1.850 0.079 812040 4 4 12 19 47 2
712104 1/4" 0.250 0.500 0.748 1.850 0.079 812050 HK12 5 5 12 19 47 2
712516 5/16" 0.313 0.500 0.748 1.850 0.079 812060 6 6 12 19 47 2
725108 1/8" 0.125 0.750 1.063 2.067 0.079 812070 7 7 12 19 47 2
725316 3/16" 0.188 0.750 1.063 2.067 0.079 812008 8 8 12 19 47 2
725104 1/4" 0.250 0.750 1.063 2.067 0.079 820030 3 3 20 27 52.5 2
725516 HS3/4" 5/16" 0.313 0.750 1.063 2.067 0.079 820040 4 4 20 27 52.5 2
725308 3/8" 0.375 0.750 1.063 2.067 0.079 820050 5 5 20 27 52.5 2
725102 1/2" 0.500 0.750 1.063 2.067 0.079 820060 6 6 20 27 52.5 2
52.5
27
2
820070
20
7
7
725508 5/8" 0.625 0.750 1.063 2.067 0.079 820080 8 8 20 27 52.5 2
732108 1/8" 0.125 1.250 1.535 2.500 0.118 820090 9 9 20 27 52.5 2
732316 3/16" 0.188 1.250 1.535 2.500 0.118 820100 HK20 10 10 20 27 52.5 2
732104 1/4" 0.250 1.250 1.535 2.500 0.118 820110 11 11 20 27 52.5 2
732516 5/16" 0.313 1.250 1.535 2.500 0.118 820120 12 12 20 27 52.5 2
732308 HS1 1/4" 3/8" 0.375 1.250 1.535 2.500 0.118 820130 13 13 20 27 52.5 2
732102 1/2" 0.500 1.250 1.535 2.500 0.118 820140 14 14 20 27 52.5 2
732508 5/8" 0.625 1.250 1.535 2.500 0.118 820150 15 15 20 27 52.5 2
732304 3/4" 0.750 1.250 1.535 2.500 0.118 820160 16 16 20 27 52.5 2
732100 1 1.000 1.250 1.535 2.500 0.118 832060 6 6 32 39 63.5 3
832080 8 8 32 39 63.5 3
* Other special sizes of Hydraulic Chuck collets can be supplied on request. 832100 10 10 32 39 63.5 3
832120 12 12 32 39 63.5 3
832140 HK32 14 14 32 39 63.5 3
832160 16 16 32 39 63.5 3
832180 18 18 32 39 63.5 3
Feature The wall of Hydraulic Chuck collet(reduction sleeve) is cut by high precision wire-cutting to 832200 20 20 32 39 63.5 3
guarantee precise I.D and strong clamping power.
832250 25 25 32 39 63.5 3
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.
* Other special sizes of Hydraulic Chuck collets can be supplied on request.

Feature Hydraulic Chuck collet(reduction sleeve) is cut into trisection by high precision cutting to
guarantee precise I.D and strong clamping power.
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.



1334 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1335

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE) HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : OPEN TYPE)




D1 d D2


L2
L









Hydraulic Chuck collet Hydraulic Chuck collet


METRIC / METRIC Unit : mm INCH / METRIC Unit : inch
EDP No. TYPE d D1 D2 L L2 EDP No. TYPE d D1 D2 L L2
912030 3 3 12 19 47 2 101203 3 3mm 0.500 0.748 1.850 0.079
912040 4 4 12 19 47 2 101204 4 4mm 0.500 0.748 1.850 0.079
912050 5 5 12 19 47 2 101205 HK1/2" 5 5mm 0.500 0.748 1.850 0.079
912060 HS12 6 6 12 19 47 2 101206 6 6mm 0.500 0.748 1.850 0.079
912070 7 7 12 19 47 2 101208 8 8mm 0.500 0.748 1.850 0.079
912080 8 8 12 19 47 2 102503 3 3mm 0.750 1.063 2.067 0.079
920030 3 3 20 27 52.5 2 102504 4 4mm 0.750 1.063 2.067 0.079
920040 4 4 20 27 52.5 2 102505 5 5mm 0.750 1.063 2.067 0.079
920050 5 5 20 27 52.5 2 102506 6 6mm 0.750 1.063 2.067 0.079
920060 6 6 20 27 52.5 2 102508 HK3/4" 8 8mm 0.750 1.063 2.067 0.079
920070 7 7 20 27 52.5 2 102510 10 10mm 0.750 1.063 2.067 0.079
920080 8 8 20 27 52.5 2 102512 12 12mm 0.750 1.063 2.067 0.079
920090 HS20 9 9 20 27 52.5 2 102514 14 14mm 0.750 1.063 2.067 0.079
920100 10 10 20 27 52.5 2 103208 8 8mm 1.250 1.535 2.500 0.118
920110 11 11 20 27 52.5 2 103210 10 10mm 1.250 1.535 2.500 0.118
920120 12 12 20 27 52.5 2 103212 12 12mm 1.250 1.535 2.500 0.118
920130 13 13 20 27 52.5 2 103214 HK1 1/4" 14 14mm 1.250 1.535 2.500 0.118
920140 14 14 20 27 52.5 2 103216 16 16mm 1.250 1.535 2.500 0.118
920150 15 15 20 27 52.5 2 103218 18 18mm 1.250 1.535 2.500 0.118
920160 16 16 20 27 52.5 2 103220 20 20mm 1.250 1.535 2.500 0.118
932060 6 6 32 39 63.5 3 103225 25 25mm 1.250 1.535 2.500 0.118
932080 8 8 32 39 63.5 3
932100 10 10 32 39 63.5 3 * Other special sizes of Hydraulic Chuck collets can be supplied on request.
932120 12 12 32 39 63.5 3
932140 HS32 14 14 32 39 63.5 3 Hydraulic Chuck collet(reduction sleeve) is cut into trisection by high precision cutting to
932160 16 16 32 39 63.5 3 Feature guarantee precise I.D and strong clamping power.
932180 18 18 32 39 63.5 3
932200 20 20 32 39 63.5 3 Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.
932250 25 25 32 39 63.5 3
* Other special sizes of Hydraulic Chuck collets can be supplied on request.


Feature The wall of Hydraulic Chuck collet(reduction sleeve) is cut by high precision wire-cutting to
guarantee precise I.D and strong clamping power.
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.

1336 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1337

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE) HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : OPEN TYPE)




D1 d D2


L2
L









Hydraulic Chuck collet Hydraulic Chuck collet


METRIC / METRIC Unit : mm INCH / METRIC Unit : inch
EDP No. TYPE d D1 D2 L L2 EDP No. TYPE d D1 D2 L L2
912030 3 3 12 19 47 2 101203 3 3mm 0.500 0.748 1.850 0.079
912040 4 4 12 19 47 2 101204 4 4mm 0.500 0.748 1.850 0.079
912050 5 5 12 19 47 2 101205 HK1/2" 5 5mm 0.500 0.748 1.850 0.079
912060 HS12 6 6 12 19 47 2 101206 6 6mm 0.500 0.748 1.850 0.079
912070 7 7 12 19 47 2 101208 8 8mm 0.500 0.748 1.850 0.079
912080 8 8 12 19 47 2 102503 3 3mm 0.750 1.063 2.067 0.079
920030 3 3 20 27 52.5 2 102504 4 4mm 0.750 1.063 2.067 0.079
920040 4 4 20 27 52.5 2 102505 5 5mm 0.750 1.063 2.067 0.079
920050 5 5 20 27 52.5 2 102506 6 6mm 0.750 1.063 2.067 0.079
920060 6 6 20 27 52.5 2 102508 HK3/4" 8 8mm 0.750 1.063 2.067 0.079
920070 7 7 20 27 52.5 2 102510 10 10mm 0.750 1.063 2.067 0.079
920080 8 8 20 27 52.5 2 102512 12 12mm 0.750 1.063 2.067 0.079
920090 HS20 9 9 20 27 52.5 2 102514 14 14mm 0.750 1.063 2.067 0.079
920100 10 10 20 27 52.5 2 103208 8 8mm 1.250 1.535 2.500 0.118
920110 11 11 20 27 52.5 2 103210 10 10mm 1.250 1.535 2.500 0.118
920120 12 12 20 27 52.5 2 103212 12 12mm 1.250 1.535 2.500 0.118
920130 13 13 20 27 52.5 2 103214 HK1 1/4" 14 14mm 1.250 1.535 2.500 0.118
920140 14 14 20 27 52.5 2 103216 16 16mm 1.250 1.535 2.500 0.118
920150 15 15 20 27 52.5 2 103218 18 18mm 1.250 1.535 2.500 0.118
920160 16 16 20 27 52.5 2 103220 20 20mm 1.250 1.535 2.500 0.118
932060 6 6 32 39 63.5 3 103225 25 25mm 1.250 1.535 2.500 0.118
932080 8 8 32 39 63.5 3
932100 10 10 32 39 63.5 3 * Other special sizes of Hydraulic Chuck collets can be supplied on request.
932120 12 12 32 39 63.5 3
932140 HS32 14 14 32 39 63.5 3 Hydraulic Chuck collet(reduction sleeve) is cut into trisection by high precision cutting to
932160 16 16 32 39 63.5 3 Feature guarantee precise I.D and strong clamping power.
932180 18 18 32 39 63.5 3
932200 20 20 32 39 63.5 3 Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.
932250 25 25 32 39 63.5 3
* Other special sizes of Hydraulic Chuck collets can be supplied on request.


Feature The wall of Hydraulic Chuck collet(reduction sleeve) is cut by high precision wire-cutting to
guarantee precise I.D and strong clamping power.
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck.

1336 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1337

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE) SHRINK FIT HOLDER CAT



G L2
4°30'


d1 D1 D2


TAPER No.
L



Taper Run-Out Coolant
Hydraulic Chuck collet ASME B5.50 Accuracy G Value RPM (at 3D) System
- CAT AT3 2.5 25,000 ≤0.00012" AD/B

INCH / METRIC Unit : inch ASME B5.50-2009-CAT Unit : inch
EDP No. TYPE d D1 D2 L L2 EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
111203 3 3mm 0.500 0.748 1.850 0.079 VK020 CAT40 AD/B - SFH 1/8 - 3.15 0.125 0.394 0.748 3.150 0.354 -
111204 4 4mm 0.500 0.748 1.850 0.079 VK022 CAT40 AD/B - SFH 3/16 - 3.15 0.188 0.394 0.748 3.150 0.472 -
111205 HS1/2" 5 5mm 0.500 0.748 1.850 0.079 VK024 CAT40 AD/B - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
111206 6 6mm 0.500 0.748 1.850 0.079 VK026 CAT40 AD/B - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
111208 8 8mm 0.500 0.748 1.850 0.079 VK028 CAT40 AD/B - SFH 3/8 - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm
112503 3 3mm 0.750 1.063 2.067 0.079 VK030 CAT40 AD/B - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
112504 4 4mm 0.750 1.063 2.067 0.079 VK032 CAT40 AD/B - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.811 M10x1.0mm
112505 5 5mm 0.750 1.063 2.067 0.079 VK034 40 CAT40 AD/B - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
112506 6 6mm 0.750 1.063 2.067 0.079 VK036 CAT40 AD/B - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
112508 HS3/4" 8 8mm 0.750 1.063 2.067 0.079 VK038 CAT40 AD/B - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
112510 10 10mm 0.750 1.063 2.067 0.079 VK040 CAT40 AD/B - SFH 3/4 - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
112512 12 12mm 0.750 1.063 2.067 0.079 VK042 CAT40 AD/B - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
112514 14 14mm 0.750 1.063 2.067 0.079 VK044 CAT40 AD/B - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
113208 8 8mm 1.250 1.535 2.500 0.118 VK046 CAT40 AD/B - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
113210 10 10mm 1.250 1.535 2.500 0.118 VK048 CAT40 AD/B - SFH 1 1/4 - 3.94 1.250 1.732 2.087 3.937 2.283 M16x1.0mm
113212 12 12mm 1.250 1.535 2.500 0.118 VK050 CAT40 AD/B - SFH 1 1/4 - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm
113214 HS1 1/4" 14 14mm 1.250 1.535 2.500 0.118 VL020 CAT50 AD/B - SFH 1/8 - 3.15 0.125 0.394 0.748 3.150 0.354 -
113216 16 16mm 1.250 1.535 2.500 0.118 VL022 CAT50 AD/B - SFH 3/16 - 3.15 0.188 0.394 0.748 3.150 0.472 -
113218 18 18mm 1.250 1.535 2.500 0.118 VL024 CAT50 AD/B - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
113220 20 20mm 1.250 1.535 2.500 0.118 VL026 CAT50 AD/B - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
113225 25 25mm 1.250 1.535 2.500 0.118 VL028 CAT50 AD/B - SFH 3/8 - 3.15 0.375 0.945 1.260 3.150 1.575 M8x1.0mm
VL030 CAT50 AD/B - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.575 M8x1.0mm
* Other special sizes of Hydraulic Chuck collets can be supplied on request. VL032 CAT50 AD/B - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VL034 CAT50 AD/B - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VL036 50 CAT50 AD/B - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
Feature The wall of Hydraulic Chuck collet(reduction sleeve) is cut by high precision wire-cutting to VL038 CAT50 AD/B - SFH 5/8 - 6.3 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
guarantee precise I.D and strong clamping power.
VL040 CAT50 AD/B - SFH 3/4 - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck. VL042 CAT50 AD/B - SFH 3/4 - 6.3 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VL044 CAT50 AD/B - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
VL046 CAT50 AD/B - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VL048 CAT50 AD/B - SFH 1 1/4 - 3.94 1.250 1.732 2.087 3.937 2.283 M16x1.0mm
VL050 CAT50 AD/B - SFH 1 1/4 - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm






1338 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1339

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS




HYDRAULIC CHUCK COLLET (REDUCTION SLEEVE : CLOSED TYPE) SHRINK FIT HOLDER CAT



G L2
4°30'


d1 D1 D2


TAPER No.
L



Taper Run-Out Coolant
Hydraulic Chuck collet ASME B5.50 Accuracy G Value RPM (at 3D) System
- CAT AT3 2.5 25,000 ≤0.00012" AD/B

INCH / METRIC Unit : inch ASME B5.50-2009-CAT Unit : inch
EDP No. TYPE d D1 D2 L L2 EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
111203 3 3mm 0.500 0.748 1.850 0.079 VK020 CAT40 AD/B - SFH 1/8 - 3.15 0.125 0.394 0.748 3.150 0.354 -
111204 4 4mm 0.500 0.748 1.850 0.079 VK022 CAT40 AD/B - SFH 3/16 - 3.15 0.188 0.394 0.748 3.150 0.472 -
111205 HS1/2" 5 5mm 0.500 0.748 1.850 0.079 VK024 CAT40 AD/B - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
111206 6 6mm 0.500 0.748 1.850 0.079 VK026 CAT40 AD/B - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
111208 8 8mm 0.500 0.748 1.850 0.079 VK028 CAT40 AD/B - SFH 3/8 - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm
112503 3 3mm 0.750 1.063 2.067 0.079 VK030 CAT40 AD/B - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
112504 4 4mm 0.750 1.063 2.067 0.079 VK032 CAT40 AD/B - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.811 M10x1.0mm
112505 5 5mm 0.750 1.063 2.067 0.079 VK034 40 CAT40 AD/B - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
112506 6 6mm 0.750 1.063 2.067 0.079 VK036 CAT40 AD/B - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
112508 HS3/4" 8 8mm 0.750 1.063 2.067 0.079 VK038 CAT40 AD/B - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
112510 10 10mm 0.750 1.063 2.067 0.079 VK040 CAT40 AD/B - SFH 3/4 - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
112512 12 12mm 0.750 1.063 2.067 0.079 VK042 CAT40 AD/B - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
112514 14 14mm 0.750 1.063 2.067 0.079 VK044 CAT40 AD/B - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
113208 8 8mm 1.250 1.535 2.500 0.118 VK046 CAT40 AD/B - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
113210 10 10mm 1.250 1.535 2.500 0.118 VK048 CAT40 AD/B - SFH 1 1/4 - 3.94 1.250 1.732 2.087 3.937 2.283 M16x1.0mm
113212 12 12mm 1.250 1.535 2.500 0.118 VK050 CAT40 AD/B - SFH 1 1/4 - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm
113214 HS1 1/4" 14 14mm 1.250 1.535 2.500 0.118 VL020 CAT50 AD/B - SFH 1/8 - 3.15 0.125 0.394 0.748 3.150 0.354 -
113216 16 16mm 1.250 1.535 2.500 0.118 VL022 CAT50 AD/B - SFH 3/16 - 3.15 0.188 0.394 0.748 3.150 0.472 -
113218 18 18mm 1.250 1.535 2.500 0.118 VL024 CAT50 AD/B - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
113220 20 20mm 1.250 1.535 2.500 0.118 VL026 CAT50 AD/B - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
113225 25 25mm 1.250 1.535 2.500 0.118 VL028 CAT50 AD/B - SFH 3/8 - 3.15 0.375 0.945 1.260 3.150 1.575 M8x1.0mm
VL030 CAT50 AD/B - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.575 M8x1.0mm
* Other special sizes of Hydraulic Chuck collets can be supplied on request. VL032 CAT50 AD/B - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VL034 CAT50 AD/B - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VL036 50 CAT50 AD/B - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
Feature The wall of Hydraulic Chuck collet(reduction sleeve) is cut by high precision wire-cutting to VL038 CAT50 AD/B - SFH 5/8 - 6.3 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
guarantee precise I.D and strong clamping power.
VL040 CAT50 AD/B - SFH 3/4 - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
Chucking Method Please assemble cutting tool with collet first, and then insert collet into Hydraulic Chuck. VL042 CAT50 AD/B - SFH 3/4 - 6.3 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VL044 CAT50 AD/B - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
VL046 CAT50 AD/B - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VL048 CAT50 AD/B - SFH 1 1/4 - 3.94 1.250 1.732 2.087 3.937 2.283 M16x1.0mm
VL050 CAT50 AD/B - SFH 1 1/4 - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm






1338 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1339

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic CAT BT
Chuck SHRINK FIT HOLDER (Coolant Channel Type) SHRINK FIT HOLDER



L2 G L2
G
4°30'
4°30'
d1 D1 D2 d1 D1 D2


TAPER No. TAPER No.
L
L


Taper Run-Out Coolant Taper Run-Out Coolant
ASME B5.50 Accuracy G Value RPM (at 3D) System JIS B6339 Accuracy G Value RPM (at 3D) System
- CAT AT3 2.5 25,000 ≤0.00012" AD/B+C - BT AT3 2.5 25,000 ≤0.00012" AD or AD/B

ASME B5.50-2009-CAT Unit : inch JIS B6339/MAS 403-BT Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
VK028J CAT40 AD/B - SFH 3/8C - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm
VK030J CAT40 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VK032J CAT40 AD/B - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VK034J CAT40 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VK036J CAT40 AD/B - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VK038J CAT40 AD/B - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VK040J 40 CAT40 AD/B - SFH 3/4C - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VK042J CAT40 AD/B - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VK044J CAT40 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm
VK046J CAT40 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VK048J CAT40 AD/B - SFH 1 1/4C - 3.94 1.250 1.732 2.087 3.940 2.283 M16x1.0mm
VK050J CAT40 AD/B - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm
VL028J CAT50 AD/B - SFH 3/8C - 3.15 0.375 0.945 1.260 3.150 1.575 M8x1.0mm
VL030J CAT50 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.575 M8x1.0mm
VL032J CAT50 AD/B - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VL034J CAT50 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VL036J CAT50 AD/B - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VL038J CAT50 AD/B - SFH 5/8C - 6.3 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VL040J 50 CAT50 AD/B - SFH 3/4C - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VL042J CAT50 AD/B - SFH 3/4C - 6.3 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VL044J CAT50 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm
VL046J CAT50 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VL048J CAT50 AD/B - SFH 1 1/4C - 3.94 1.250 1.732 2.087 3.940 2.283 M16x1.0mm
VL050J CAT50 AD/B - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm
* Effective cooling by coolant through cooling channel bores.















1340 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1341

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic CAT BT
Chuck SHRINK FIT HOLDER (Coolant Channel Type) SHRINK FIT HOLDER



L2 G L2
G
4°30'
4°30'
d1 D1 D2 d1 D1 D2


TAPER No. TAPER No.
L
L


Taper Run-Out Coolant Taper Run-Out Coolant
ASME B5.50 Accuracy G Value RPM (at 3D) System JIS B6339 Accuracy G Value RPM (at 3D) System
- CAT AT3 2.5 25,000 ≤0.00012" AD/B+C - BT AT3 2.5 25,000 ≤0.00012" AD or AD/B

ASME B5.50-2009-CAT Unit : inch JIS B6339/MAS 403-BT Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
VK028J CAT40 AD/B - SFH 3/8C - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm
VK030J CAT40 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VK032J CAT40 AD/B - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VK034J CAT40 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VK036J CAT40 AD/B - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VK038J CAT40 AD/B - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VK040J 40 CAT40 AD/B - SFH 3/4C - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VK042J CAT40 AD/B - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VK044J CAT40 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm
VK046J CAT40 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VK048J CAT40 AD/B - SFH 1 1/4C - 3.94 1.250 1.732 2.087 3.940 2.283 M16x1.0mm
VK050J CAT40 AD/B - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm
VL028J CAT50 AD/B - SFH 3/8C - 3.15 0.375 0.945 1.260 3.150 1.575 M8x1.0mm
VL030J CAT50 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.575 M8x1.0mm
VL032J CAT50 AD/B - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VL034J CAT50 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VL036J CAT50 AD/B - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VL038J CAT50 AD/B - SFH 5/8C - 6.3 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VL040J 50 CAT50 AD/B - SFH 3/4C - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VL042J CAT50 AD/B - SFH 3/4C - 6.3 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VL044J CAT50 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm
VL046J CAT50 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VL048J CAT50 AD/B - SFH 1 1/4C - 3.94 1.250 1.732 2.087 3.940 2.283 M16x1.0mm
VL050J CAT50 AD/B - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm
* Effective cooling by coolant through cooling channel bores.















1340 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1341

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic BT CCT
Chuck SHRINK FIT HOLDER (Coolant Channel Type) DUAL CONTACT SHRINK FIT HOLDER




G L2 G L2
4°30'
4°30'
d1 D1 D2 d1 D1 D2

TAPER No. TAPER No.
L
L


Taper Run-Out Coolant Taper Run-Out Coolant
JIS B6339 Accuracy G Value RPM (at 3D) System CCT Accuracy G Value RPM (at 3D) System
- BT AT3 2.5 25,000 ≤0.00012" AD+C or AT3 2.5 25,000 ≤0.00012" AD/B
AD/B+C
JIS B6339/MAS 403-BT Unit : inch CCT (CAT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
VG024J BT30 - SFH 1/4C - 2.36 0.250 0.827 1.063 2.360 1.417 M5x0.8mm VB020 CCT40 AD/B - SFH 1/8 - 3.15 0.125 0.394 0.748 3.150 0.354 -
VG026J BT30 - SFH 3/8C - 2.36 0.375 0.945 1.180 2.360 1.654 M8x1.0mm VB022 CCT40 AD/B - SFH 3/16 - 3.15 0.188 0.394 0.748 3.150 0.472 -
VG028J 30 BT30 - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm VB024 CCT40 AD/B - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
VG030J BT30 - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm VB026 CCT40 AD/B - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
VG032J BT30 - SFH 3/4C - 3.54 0.750 1.299 1.654 3.540 2.008 M16x1.0mm VB028 CCT40 AD/B - SFH 3/8 - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm
VH024J BT40 AD/B - SFH 1/4C - 3.54 0.250 0.827 1.063 3.540 1.417 M5x0.8mm VB030 CCT40 AD/B - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VH026J BT40 AD/B - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VB032 CCT40 AD/B - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VH028J BT40 AD/B - SFH 3/8C - 3.54 0.375 0.945 1.260 3.540 1.654 M8x1.0mm VB034 40 CCT40 AD/B - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VH030J BT40 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VB036 CCT40 AD/B - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VH032J BT40 AD/B - SFH 1/2C - 3.54 0.500 0.945 1.260 3.540 1.850 M10x1.0mm VB038 CCT40 AD/B - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VH034J 40 BT40 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VB040 CCT40 AD/B - SFH 3/4 - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VH036J BT40 AD/B - SFH 5/8C - 3.54 0.625 1.063 1.339 3.540 1.969 M12x1.0mm VB042 CCT40 AD/B - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VH038J BT40 AD/B - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VB044 CCT40 AD/B - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
VH040J BT40 AD/ 4C - 3.54 0.750 1.299 1.654 3.540 2.047 M16x1.0mm VB046 CCT40 AD/B - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VH042J BT40 AD/B - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VB048 CCT40 AD/B - SFH 1 1/4 - 3.94 1.250 1.732 2.087 3.937 2.283 M16x1.0mm
VH044J BT40 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm VB050 CCT40 AD/B - SFH 1 1/4 - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm
VH046J BT40 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VC020 CCT50 AD/B - SFH 1/8 - 3.15 0.125 0.394 0.748 3.150 0.354 -
VC022 CCT50 AD/B - SFH 3/16 - 3.15 0.188 0.394 0.748 3.150 0.472 -
* Effective cooling by coolant through cooling channel bores. VC024 CCT50 AD/B - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
VC026 CCT50 AD/B - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
VC028 CCT50 AD/B - SFH 3/8 - 3.15 0.375 0.945 1.260 3.150 1.575 M8x1.0mm
VC030 CCT50 AD/B - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.575 M8x1.0mm
VC032 CCT50 AD/B - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VC034 CCT50 AD/B - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VC036 50 CCT50 AD/B - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VC040 CCT50 AD/B - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VC042 CCT50 AD/B - SFH 3/4 - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VC044 CCT50 AD/B - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VC046 CCT50 AD/B - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
VC048 CCT50 AD/B - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VC050 CCT50 AD/B - SFH 1 1/4 - 3.94 1.250 1.732 2.087 3.937 2.283 M16x1.0mm
VC052 CCT50 AD/B - SFH 1 1/4 - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm






1342 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1343

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic BT CCT
Chuck SHRINK FIT HOLDER (Coolant Channel Type) DUAL CONTACT SHRINK FIT HOLDER




G L2 G L2
4°30'
4°30'
d1 D1 D2 d1 D1 D2

TAPER No. TAPER No.
L
L


Taper Run-Out Coolant Taper Run-Out Coolant
JIS B6339 Accuracy G Value RPM (at 3D) System CCT Accuracy G Value RPM (at 3D) System
- BT AT3 2.5 25,000 ≤0.00012" AD+C or AT3 2.5 25,000 ≤0.00012" AD/B
AD/B+C
JIS B6339/MAS 403-BT Unit : inch CCT (CAT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
VG024J BT30 - SFH 1/4C - 2.36 0.250 0.827 1.063 2.360 1.417 M5x0.8mm VB020 CCT40 AD/B - SFH 1/8 - 3.15 0.125 0.394 0.748 3.150 0.354 -
VG026J BT30 - SFH 3/8C - 2.36 0.375 0.945 1.180 2.360 1.654 M8x1.0mm VB022 CCT40 AD/B - SFH 3/16 - 3.15 0.188 0.394 0.748 3.150 0.472 -
VG028J 30 BT30 - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm VB024 CCT40 AD/B - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
VG030J BT30 - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm VB026 CCT40 AD/B - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
VG032J BT30 - SFH 3/4C - 3.54 0.750 1.299 1.654 3.540 2.008 M16x1.0mm VB028 CCT40 AD/B - SFH 3/8 - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm
VH024J BT40 AD/B - SFH 1/4C - 3.54 0.250 0.827 1.063 3.540 1.417 M5x0.8mm VB030 CCT40 AD/B - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VH026J BT40 AD/B - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VB032 CCT40 AD/B - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VH028J BT40 AD/B - SFH 3/8C - 3.54 0.375 0.945 1.260 3.540 1.654 M8x1.0mm VB034 40 CCT40 AD/B - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VH030J BT40 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VB036 CCT40 AD/B - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VH032J BT40 AD/B - SFH 1/2C - 3.54 0.500 0.945 1.260 3.540 1.850 M10x1.0mm VB038 CCT40 AD/B - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VH034J 40 BT40 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VB040 CCT40 AD/B - SFH 3/4 - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VH036J BT40 AD/B - SFH 5/8C - 3.54 0.625 1.063 1.339 3.540 1.969 M12x1.0mm VB042 CCT40 AD/B - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VH038J BT40 AD/B - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VB044 CCT40 AD/B - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
VH040J BT40 AD/ 4C - 3.54 0.750 1.299 1.654 3.540 2.047 M16x1.0mm VB046 CCT40 AD/B - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VH042J BT40 AD/B - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VB048 CCT40 AD/B - SFH 1 1/4 - 3.94 1.250 1.732 2.087 3.937 2.283 M16x1.0mm
VH044J BT40 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm VB050 CCT40 AD/B - SFH 1 1/4 - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm
VH046J BT40 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VC020 CCT50 AD/B - SFH 1/8 - 3.15 0.125 0.394 0.748 3.150 0.354 -
VC022 CCT50 AD/B - SFH 3/16 - 3.15 0.188 0.394 0.748 3.150 0.472 -
* Effective cooling by coolant through cooling channel bores. VC024 CCT50 AD/B - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
VC026 CCT50 AD/B - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
VC028 CCT50 AD/B - SFH 3/8 - 3.15 0.375 0.945 1.260 3.150 1.575 M8x1.0mm
VC030 CCT50 AD/B - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.575 M8x1.0mm
VC032 CCT50 AD/B - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VC034 CCT50 AD/B - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VC036 50 CCT50 AD/B - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VC040 CCT50 AD/B - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VC042 CCT50 AD/B - SFH 3/4 - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VC044 CCT50 AD/B - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VC046 CCT50 AD/B - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
VC048 CCT50 AD/B - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VC050 CCT50 AD/B - SFH 1 1/4 - 3.94 1.250 1.732 2.087 3.937 2.283 M16x1.0mm
VC052 CCT50 AD/B - SFH 1 1/4 - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm






1342 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1343

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic CCT CBT
Chuck DUAL CONTACT SHRINK FIT HOLDER (Coolant Channel Type) DUAL CONTACT SHRINK FIT HOLDER



L2
G 4°30' G L2
4°30'

d1 D1 D2 d1 D1 D2


TAPER No.
TAPER No.
L L



Taper Run-Out Coolant Taper Run-Out Coolant
Accuracy G Value RPM (at 3D) System Accuracy G Value RPM (at 3D) System
CCT CBT
AT3 2.5 25,000 ≤0.00012" AD/B+C AT3 2.5 25,000 ≤0.00012" AD
CCT (CAT DUAL CONTACT) Unit : inch CBT (BT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
VB024J CCT40 AD/B - SFH 1/4C - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm VD020 CBT30 - SFH 1/8 - 2.36 0.125 0.394 0.629 2.362 0.354 -
VB026J CCT40 AD/B - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VD022 CBT30 - SFH 3/16 - 2.36 0.188 0.394 0.629 2.362 0.472 -
VB028J CCT40 AD/B - SFH 3/8C - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm VD024 CBT30 - SFH 1/4 - 2.36 0.250 0.827 1.062 2.362 1.417 M5x0.8mm
VB030J CCT40 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VD026 30 CBT30 - SFH 3/8 - 2.36 0.375 0.945 1.180 2.362 1.614 M8x1.0mm
VB032J CCT40 AD/B - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm VD028 CBT30 - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VB034J CCT40 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VD030 CBT30 - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VB036J 40 CCT40 AD/B - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm VD032 CBT30 - SFH 3/4 - 3.54 0.750 1.299 1.654 3.543 2.047 M16x1.0mm
VB038J CCT40 AD/B - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VE020 CBT40 - SFH 1/8 - 3.54 0.125 0.394 0.748 3.543 0.354 -
VB040J CCT40 AD/B - SFH 3/4C - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm VE022 CBT40 - SFH 3/16 - 3.54 0.188 0.394 0.748 3.543 0.472 -
VB042J CCT40 AD/B - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VE024 CBT40 - SFH 1/4 - 3.54 0.250 0.827 1.063 3.543 1.417 M5x0.8mm
VB044J CCT40 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm VE026 CBT40 - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
VB046J CCT40 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VE028 CBT40 - SFH 3/8 - 3.54 0.375 0.945 1.260 3.543 1.654 M8x1.0mm
VB048J CCT40 AD/B - SFH 1 1/4C - 3.94 1.250 1.732 2.087 3.940 2.283 M16x1.0mm VE030 CBT40 - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VB050J CCT40 AD/B - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm VE032 40 CBT40 - SFH 1/2 - 3.54 0.500 0.945 1.260 3.543 1.850 M10x1.0mm
VC024J CCT50 AD/B - SFH 1/4C - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm VE034 CBT40 - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VC026J CCT50 AD/B - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VE036 CBT40 - SFH 5/8 - 3.54 0.625 1.063 1.339 3.543 1.969 M12x1.0mm
VC028J CCT50 AD/B - SFH 3/8C - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm VE038 CBT40 - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VC030J CCT50 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VE040 CBT40 - SFH 3/4 - 3.54 0.750 1.299 1.654 3.543 2.047 M16x1.0mm
VC032J CCT50 AD/B - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm VE042 CBT40 - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VC034J CCT50 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VE044 CBT40 - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
VC036J CCT50 AD/B - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm VE046 CBT40 - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VC040J 50 CCT50 AD/B - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VC042J CCT50 AD/B - SFH 3/4C - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VC044J CCT50 AD/B - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VC046J CCT50 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm
VC048J CCT50 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VC050J CCT50 AD/B - SFH 1 1/4C - 3.94 1.250 1.732 2.087 3.940 2.283 M16x1.0mm
VC052J CCT50 AD/B - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm

* Effective cooling by coolant through cooling channel bores.









1344 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1345

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic CCT CBT
Chuck DUAL CONTACT SHRINK FIT HOLDER (Coolant Channel Type) DUAL CONTACT SHRINK FIT HOLDER



L2
G 4°30' G L2
4°30'

d1 D1 D2 d1 D1 D2


TAPER No.
TAPER No.
L L



Taper Run-Out Coolant Taper Run-Out Coolant
Accuracy G Value RPM (at 3D) System Accuracy G Value RPM (at 3D) System
CCT CBT
AT3 2.5 25,000 ≤0.00012" AD/B+C AT3 2.5 25,000 ≤0.00012" AD
CCT (CAT DUAL CONTACT) Unit : inch CBT (BT DUAL CONTACT) Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
VB024J CCT40 AD/B - SFH 1/4C - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm VD020 CBT30 - SFH 1/8 - 2.36 0.125 0.394 0.629 2.362 0.354 -
VB026J CCT40 AD/B - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VD022 CBT30 - SFH 3/16 - 2.36 0.188 0.394 0.629 2.362 0.472 -
VB028J CCT40 AD/B - SFH 3/8C - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm VD024 CBT30 - SFH 1/4 - 2.36 0.250 0.827 1.062 2.362 1.417 M5x0.8mm
VB030J CCT40 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VD026 30 CBT30 - SFH 3/8 - 2.36 0.375 0.945 1.180 2.362 1.614 M8x1.0mm
VB032J CCT40 AD/B - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm VD028 CBT30 - SFH 1/2 - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm
VB034J CCT40 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VD030 CBT30 - SFH 5/8 - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm
VB036J 40 CCT40 AD/B - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm VD032 CBT30 - SFH 3/4 - 3.54 0.750 1.299 1.654 3.543 2.047 M16x1.0mm
VB038J CCT40 AD/B - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VE020 CBT40 - SFH 1/8 - 3.54 0.125 0.394 0.748 3.543 0.354 -
VB040J CCT40 AD/B - SFH 3/4C - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm VE022 CBT40 - SFH 3/16 - 3.54 0.188 0.394 0.748 3.543 0.472 -
VB042J CCT40 AD/B - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VE024 CBT40 - SFH 1/4 - 3.54 0.250 0.827 1.063 3.543 1.417 M5x0.8mm
VB044J CCT40 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm VE026 CBT40 - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
VB046J CCT40 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VE028 CBT40 - SFH 3/8 - 3.54 0.375 0.945 1.260 3.543 1.654 M8x1.0mm
VB048J CCT40 AD/B - SFH 1 1/4C - 3.94 1.250 1.732 2.087 3.940 2.283 M16x1.0mm VE030 CBT40 - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VB050J CCT40 AD/B - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm VE032 40 CBT40 - SFH 1/2 - 3.54 0.500 0.945 1.260 3.543 1.850 M10x1.0mm
VC024J CCT50 AD/B - SFH 1/4C - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm VE034 CBT40 - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VC026J CCT50 AD/B - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VE036 CBT40 - SFH 5/8 - 3.54 0.625 1.063 1.339 3.543 1.969 M12x1.0mm
VC028J CCT50 AD/B - SFH 3/8C - 3.15 0.375 0.945 1.260 3.150 1.654 M8x1.0mm VE038 CBT40 - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VC030J CCT50 AD/B - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VE040 CBT40 - SFH 3/4 - 3.54 0.750 1.299 1.654 3.543 2.047 M16x1.0mm
VC032J CCT50 AD/B - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm VE042 CBT40 - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VC034J CCT50 AD/B - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VE044 CBT40 - SFH 1" - 3.94 1.000 1.732 2.087 3.937 2.283 M16x1.0mm
VC036J CCT50 AD/B - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm VE046 CBT40 - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VC040J 50 CCT50 AD/B - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VC042J CCT50 AD/B - SFH 3/4C - 3.15 0.750 1.299 1.654 3.150 2.047 M16x1.0mm
VC044J CCT50 AD/B - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VC046J CCT50 AD/B - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm
VC048J CCT50 AD/B - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VC050J CCT50 AD/B - SFH 1 1/4C - 3.94 1.250 1.732 2.087 3.940 2.283 M16x1.0mm
VC052J CCT50 AD/B - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm

* Effective cooling by coolant through cooling channel bores.









1344 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1345

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic CBT HSK
Chuck DUAL CONTACT SHRINK FIT HOLDER (Coolant Channel Type) DUAL CONTACT SHRINK FIT HOLDER


G L2
L2
4°30'
G
4°30'
d1 D1 D2 d1 D1 D2

TAPER No.
TAPER No.
L L


Taper Run-Out Coolant Taper Run-Out Coolant
Accuracy G Value RPM (at 3D) System DIN 69893 Accuracy G Value RPM (at 3D) System
CBT - HSK
AT3 2.5 25,000 ≤0.00012" AD+C AT3 2.5 25,000 ≤0.00012" AD
CBT (BT DUAL CONTACT) Unit : inch DIN 69893/ISO 12164-1-HSK FORM A Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
VD024J CBT30 - SFH 1/4C - 2.36 0.250 0.827 1.062 2.360 1.417 M5x0.8mm VQ020 HSK 63A - SFH 1/8 - 3.15 0.125 0.394 0.728 3.150 0.354 -
VD026J CBT30 - SFH 3/8C - 2.36 0.375 0.945 1.180 2.360 1.614 M8x1.0mm VQ022 HSK 63A - SFH 3/16 - 3.15 0.188 0.394 0.728 3.150 0.472 -
VD028J 30 CBT30 - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm VQ024 HSK 63A - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
VD030J CBT30 - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm VQ026 HSK 63A - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
VD032J CBT30 - SFH 3/4C - 3.54 0.750 1.299 1.654 3.540 2.047 M16x1.0mm VQ028 HSK 63A - SFH 3/8 - 3.35 0.375 0.945 1.260 3.346 1.654 M8x1.0mm
VE024J CBT40 - SFH 1/4C - 3.54 0.250 0.827 1.063 3.540 1.417 M5x0.8mm VQ030 HSK 63A - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VE026J CBT40 - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VQ032 63A HSK 63A - SFH 1/2 - 3.54 0.500 0.945 1.260 3.543 1.850 M10x1.0mm
VE028J CBT40 - SFH 3/8C - 3.54 0.375 0.945 1.260 3.540 1.654 M8x1.0mm VQ034 HSK 63A - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VE030J CBT40 - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VQ036 HSK 63A - SFH 5/8 - 3.74 0.625 1.063 1.339 3.740 1.969 M12x1.0mm
VE032J CBT40 - SFH 1/2C - 3.54 0.500 0.945 1.260 3.540 1.850 M10x1.0mm VQ038 HSK 63A - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VE034J 40 CBT40 - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VQ040 HSK 63A - SFH 3/4 - 3.94 0.750 1.299 1.654 3.937 2.047 M16x1.0mm
VE036J CBT40 - SFH 5/8C - 3.54 0.625 1.063 1.339 3.540 1.969 M12x1.0mm VQ042 HSK 63A - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VE038J CBT40 - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VQ046 HSK 63A - SFH 1" - 4.53 1.000 1.732 2.087 4.528 2.283 M16x1.0mm
VE040J CBT40 - SFH 3/4C - 3.54 0.750 1.299 1.654 3.540 2.047 M16x1.0mm VQ048 HSK 63A - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VE042J CBT40 - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VR020 HSK 100A - SFH 1/8 - 3.15 0.125 0.394 0.648 3.150 0.354 -
VE044J CBT40 - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm VR022 HSK 100A - SFH 3/16 - 3.15 0.188 0.394 0.648 3.150 0.472 -
VE046J CBT40 - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VR023 HSK 100A - SFH 1/4 - 3.15 0,250 0.827 1.063 3.150 1.417 M5x0.8mm
VR024 HSK 100A - SFH 3/8 - 3.54 0.375 0.945 1.260 3.543 1.654 M8x1.0mm
* Effective cooling by coolant through cooling channel bores. VR026 HSK 100A - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VR028 HSK 100A - SFH 1/2 - 3.74 0.500 0.945 1.260 3.740 1.850 M10x1.0mm
VR030 HSK 100A - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VR032 100A HSK 100A - SFH 5/8 - 3.94 0.625 1.063 1.339 3.937 1.969 M12x1.0mm
VR034 HSK 100A - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VR036 HSK 100A - SFH 3/4 - 4.13 0.750 1.299 1.654 4.134 2.047 M16x1.0mm
VR038 HSK 100A - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VR040 HSK 100A - SFH 1" - 4.53 1.000 1.732 2.087 4.528 2.283 M16x1.0mm
VR042 HSK 100A - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VR044 HSK 100A - SFH 1 1/4 - 4.72 1.250 1.732 2.087 4.724 2.283 M16x1.0mm
VR046 HSK 100A - SFH 1 1/4" - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm










1346 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1347

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic CBT HSK
Chuck DUAL CONTACT SHRINK FIT HOLDER (Coolant Channel Type) DUAL CONTACT SHRINK FIT HOLDER


G L2
L2
4°30'
G
4°30'
d1 D1 D2 d1 D1 D2

TAPER No.
TAPER No.
L L


Taper Run-Out Coolant Taper Run-Out Coolant
Accuracy G Value RPM (at 3D) System DIN 69893 Accuracy G Value RPM (at 3D) System
CBT - HSK
AT3 2.5 25,000 ≤0.00012" AD+C AT3 2.5 25,000 ≤0.00012" AD
CBT (BT DUAL CONTACT) Unit : inch DIN 69893/ISO 12164-1-HSK FORM A Unit : inch
EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G
VD024J CBT30 - SFH 1/4C - 2.36 0.250 0.827 1.062 2.360 1.417 M5x0.8mm VQ020 HSK 63A - SFH 1/8 - 3.15 0.125 0.394 0.728 3.150 0.354 -
VD026J CBT30 - SFH 3/8C - 2.36 0.375 0.945 1.180 2.360 1.614 M8x1.0mm VQ022 HSK 63A - SFH 3/16 - 3.15 0.188 0.394 0.728 3.150 0.472 -
VD028J 30 CBT30 - SFH 1/2C - 3.15 0.500 0.945 1.260 3.150 1.850 M10x1.0mm VQ024 HSK 63A - SFH 1/4 - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm
VD030J CBT30 - SFH 5/8C - 3.15 0.625 1.063 1.339 3.150 1.969 M12x1.0mm VQ026 HSK 63A - SFH 1/4 - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm
VD032J CBT30 - SFH 3/4C - 3.54 0.750 1.299 1.654 3.540 2.047 M16x1.0mm VQ028 HSK 63A - SFH 3/8 - 3.35 0.375 0.945 1.260 3.346 1.654 M8x1.0mm
VE024J CBT40 - SFH 1/4C - 3.54 0.250 0.827 1.063 3.540 1.417 M5x0.8mm VQ030 HSK 63A - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VE026J CBT40 - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VQ032 63A HSK 63A - SFH 1/2 - 3.54 0.500 0.945 1.260 3.543 1.850 M10x1.0mm
VE028J CBT40 - SFH 3/8C - 3.54 0.375 0.945 1.260 3.540 1.654 M8x1.0mm VQ034 HSK 63A - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VE030J CBT40 - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VQ036 HSK 63A - SFH 5/8 - 3.74 0.625 1.063 1.339 3.740 1.969 M12x1.0mm
VE032J CBT40 - SFH 1/2C - 3.54 0.500 0.945 1.260 3.540 1.850 M10x1.0mm VQ038 HSK 63A - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VE034J 40 CBT40 - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VQ040 HSK 63A - SFH 3/4 - 3.94 0.750 1.299 1.654 3.937 2.047 M16x1.0mm
VE036J CBT40 - SFH 5/8C - 3.54 0.625 1.063 1.339 3.540 1.969 M12x1.0mm VQ042 HSK 63A - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VE038J CBT40 - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VQ046 HSK 63A - SFH 1" - 4.53 1.000 1.732 2.087 4.528 2.283 M16x1.0mm
VE040J CBT40 - SFH 3/4C - 3.54 0.750 1.299 1.654 3.540 2.047 M16x1.0mm VQ048 HSK 63A - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VE042J CBT40 - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VR020 HSK 100A - SFH 1/8 - 3.15 0.125 0.394 0.648 3.150 0.354 -
VE044J CBT40 - SFH 1C - 3.94 1.000 1.732 2.087 3.940 2.283 M16x1.0mm VR022 HSK 100A - SFH 3/16 - 3.15 0.188 0.394 0.648 3.150 0.472 -
VE046J CBT40 - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VR023 HSK 100A - SFH 1/4 - 3.15 0,250 0.827 1.063 3.150 1.417 M5x0.8mm
VR024 HSK 100A - SFH 3/8 - 3.54 0.375 0.945 1.260 3.543 1.654 M8x1.0mm
* Effective cooling by coolant through cooling channel bores. VR026 HSK 100A - SFH 3/8 - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm
VR028 HSK 100A - SFH 1/2 - 3.74 0.500 0.945 1.260 3.740 1.850 M10x1.0mm
VR030 HSK 100A - SFH 1/2 - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm
VR032 100A HSK 100A - SFH 5/8 - 3.94 0.625 1.063 1.339 3.937 1.969 M12x1.0mm
VR034 HSK 100A - SFH 5/8 - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm
VR036 HSK 100A - SFH 3/4 - 4.13 0.750 1.299 1.654 4.134 2.047 M16x1.0mm
VR038 HSK 100A - SFH 3/4 - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm
VR040 HSK 100A - SFH 1" - 4.53 1.000 1.732 2.087 4.528 2.283 M16x1.0mm
VR042 HSK 100A - SFH 1" - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm
VR044 HSK 100A - SFH 1 1/4 - 4.72 1.250 1.732 2.087 4.724 2.283 M16x1.0mm
VR046 HSK 100A - SFH 1 1/4" - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm










1346 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1347

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic HSK ST
Chuck DUAL CONTACT SHRINK FIT HOLDER (Coolant Channel Type) SHRINK FIT EXTENSION



L2
G 4°30'

G L1
d1 D1 D2

D2 d1 D1
TAPER No.
L L



Taper Run-Out Coolant
DIN 69893 Accuracy G Value RPM (at 3D) System
- HSK AT3 2.5 25,000 ≤0.00012" AD+C

DIN 69893/ISO 12164-1-HSK FORM A Unit : inch INCH Unit : inch

EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 G
VQ024J HSK 63A - SFH 1/4C - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm VS010 ST 1/2 - SFH 1/8 - 6.30 0.125 0.394 0.500 6.300 0.354 -
VQ026J HSK 63A - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VS011 ST1/2 ST 1/2 - SFH 3/16 - 6.30 0.188 0.394 0.500 6.300 0.472 -
VQ028J HSK 63A - SFH 3/8C - 3.35 0.375 0.945 1.260 3.350 1.654 M8x1.0mm VS012 ST 1/2 - SFH 1/4 - 6.30 0.250 0.394 0.500 6.300 1.417 M5x0.8mm
VQ030J HSK 63A - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VS020 ST 5/8 - SFH 1/8 - 6.30 0.125 0.394 0.625 6.300 0.354 -
VQ032J HSK 63A - SFH 1/2C - 3.54 0.500 0.945 1.260 3.540 1.850 M10x1.0mm VS021 ST5/8 ST 5/8 - SFH 3/16 - 6.30 0.188 0.394 0.625 6.300 0.472 -
VQ034J HSK 63A - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VS022 ST 5/8 - SFH 1/4 - 6.30 0.250 0.394 0.625 6.300 1.417 M5x0.8mm
VQ036J 63A HSK 63A - SFH 5/8C - 3.74 0.625 1.063 1.339 3.740 1.969 M12x1.0mm VS023 ST 5/8 - SFH 5/16 - 6.30 0.313 0.472 0.625 6.300 1.535 M6x1.0mm
VQ038J HSK 63A - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VS030 ST 3/4 - SFH 1/8 - 6.30 0.125 0.394 0.750 6.300 0.354 -
VQ040J HSK 63A - SFH 3/4C - 3.94 0.750 1.299 1.654 3.940 2.047 M16x1.0mm VS031 ST 3/4 - SFH 3/16 - 6.30 0.188 0.394 0.750 6.300 0.472 -
VQ042J HSK 63A - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VS032 ST3/4 ST 3/4 - SFH 1/4 - 6.30 0.250 0.551 0.750 6.300 1.417 M5x0.8mm
VQ046J HSK 63A - SFH 1C - 4.53 1.000 1.732 2.087 4.530 2.283 M16x1.0mm VS033 ST 3/4 - SFH 5/16 - 6.30 0.313 0.551 0.750 6.300 1.417 M6x1.0mm
VQ048J HSK 63A - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VS034 ST 3/4 - SFH 3/8 - 6.30 0.375 0.551 0.750 6.300 1.654 M8x1.0mm
VR023J HSK 100A - SFH 1/4C - 3.54 0.250 0.827 1.063 3.540 1.417 M5x0.8mm VS035 ST 3/4 - SFH 1/2 - 6.30 0.500 0.630 0.750 6.300 1.850 M10x1.0mm
VR024J HSK 100A - SFH 3/8C - 3.54 0.375 0.945 1.260 3.540 1.654 M8x1.0mm VS040 ST 1 - SFH 1/8 - 6.30 0.125 0.394 1.000 6.300 0.354 -
VR026J HSK 100A - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VS041 ST 1 - SFH 3/16 - 6.30 0.188 0.394 1.000 6.300 0.472 -
VR028J HSK 100A - SFH 1/2C - 3.74 0.500 0.945 1.260 3.740 1.850 M10x1.0mm VS042 ST 1 - SFH 1/4 - 6.30 0.250 0.551 1.000 6.300 1.417 M5x0.8mm
VR030J HSK 100A - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VS043 ST1 ST 1 - SFH 5/16 - 6.30 0.313 0.551 1.000 6.300 1.417 M6x1.0mm
VR032J HSK 100A - SFH 5/8C - 3.94 0.625 1.063 1.339 3.940 1.969 M12x1.0mm VS044 ST 1 - SFH 3/8 - 6.30 0.375 0.787 1.000 6.300 1.654 M8x1.0mm
VR034J 100A HSK 100A - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VS045 ST 1 - SFH 1/2 - 6.30 0.500 0.787 1.000 6.300 1.850 M10x1.0mm
VR036J HSK 100A - SFH 3/4C - 4.13 0.750 1.299 1.654 4.130 2.047 M16x1.0mm VS046 ST 1 - SFH 5/8 - 6.30 0.625 0.866 1.000 6.300 1.929 M12x1.0mm
VR038J HSK 100A - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VS050 ST 1 - 1/4 - SFH 1/8 - 6.30 0.125 0.394 1.250 6.300 0.354 -
VR040J HSK 100A - SFH 1C - 4.53 1.000 1.732 2.087 4.530 2.283 M16x1.0mm VS051 ST 1 - 1/4 - SFH 3/16 - 6.30 0.188 0.394 1.250 6.300 0.472 -
VR042J HSK 100A - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VS052 ST 1 - 1/4 - SFH 1/4 - 6.30 0.250 0.551 1.250 6.300 1.417 M5x0.8mm
VR044J HSK 100A - SFH 1 1/4C - 4.72 1.250 1.732 2.087 4.720 2.283 M16x1.0mm VS053 ST1-1/4 ST 1 - 1/4 - SFH 5/16 - 6.30 0.313 0.551 1.250 6.300 1.417 M6x1.0mm
VR046J HSK 100A - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm VS054 ST 1 - 1/4 - SFH 3/8 - 6.30 0.375 0.945 1.250 6.300 1.654 M8x1.0mm
VS055 ST 1 - 1/4 - SFH 1/2 - 6.30 0.500 0.945 1.250 6.300 1.850 M10x1.0mm
* Effective cooling by coolant through cooling channel bores. VS056 ST 1 - 1/4 - SFH 5/8 - 6.30 0.625 1.063 1.250 6.300 1.929 M12x1.0mm
VS057 ST 1 - 1/4 - SFH 3/4 - 6.30 0.750 1.063 1.250 6.300 2.008 M16x1.0mm












1348 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1349

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic HSK ST
Chuck DUAL CONTACT SHRINK FIT HOLDER (Coolant Channel Type) SHRINK FIT EXTENSION



L2
G 4°30'

G L1
d1 D1 D2

D2 d1 D1
TAPER No.
L L



Taper Run-Out Coolant
DIN 69893 Accuracy G Value RPM (at 3D) System
- HSK AT3 2.5 25,000 ≤0.00012" AD+C

DIN 69893/ISO 12164-1-HSK FORM A Unit : inch INCH Unit : inch

EDP No. TAPER No. MODEL No. d1 D1 D2 L L2 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 G
VQ024J HSK 63A - SFH 1/4C - 3.15 0.250 0.827 1.063 3.150 1.417 M5x0.8mm VS010 ST 1/2 - SFH 1/8 - 6.30 0.125 0.394 0.500 6.300 0.354 -
VQ026J HSK 63A - SFH 1/4C - 6.30 0.250 0.827 1.063 6.300 1.417 M5x0.8mm VS011 ST1/2 ST 1/2 - SFH 3/16 - 6.30 0.188 0.394 0.500 6.300 0.472 -
VQ028J HSK 63A - SFH 3/8C - 3.35 0.375 0.945 1.260 3.350 1.654 M8x1.0mm VS012 ST 1/2 - SFH 1/4 - 6.30 0.250 0.394 0.500 6.300 1.417 M5x0.8mm
VQ030J HSK 63A - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VS020 ST 5/8 - SFH 1/8 - 6.30 0.125 0.394 0.625 6.300 0.354 -
VQ032J HSK 63A - SFH 1/2C - 3.54 0.500 0.945 1.260 3.540 1.850 M10x1.0mm VS021 ST5/8 ST 5/8 - SFH 3/16 - 6.30 0.188 0.394 0.625 6.300 0.472 -
VQ034J HSK 63A - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VS022 ST 5/8 - SFH 1/4 - 6.30 0.250 0.394 0.625 6.300 1.417 M5x0.8mm
VQ036J 63A HSK 63A - SFH 5/8C - 3.74 0.625 1.063 1.339 3.740 1.969 M12x1.0mm VS023 ST 5/8 - SFH 5/16 - 6.30 0.313 0.472 0.625 6.300 1.535 M6x1.0mm
VQ038J HSK 63A - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VS030 ST 3/4 - SFH 1/8 - 6.30 0.125 0.394 0.750 6.300 0.354 -
VQ040J HSK 63A - SFH 3/4C - 3.94 0.750 1.299 1.654 3.940 2.047 M16x1.0mm VS031 ST 3/4 - SFH 3/16 - 6.30 0.188 0.394 0.750 6.300 0.472 -
VQ042J HSK 63A - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VS032 ST3/4 ST 3/4 - SFH 1/4 - 6.30 0.250 0.551 0.750 6.300 1.417 M5x0.8mm
VQ046J HSK 63A - SFH 1C - 4.53 1.000 1.732 2.087 4.530 2.283 M16x1.0mm VS033 ST 3/4 - SFH 5/16 - 6.30 0.313 0.551 0.750 6.300 1.417 M6x1.0mm
VQ048J HSK 63A - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VS034 ST 3/4 - SFH 3/8 - 6.30 0.375 0.551 0.750 6.300 1.654 M8x1.0mm
VR023J HSK 100A - SFH 1/4C - 3.54 0.250 0.827 1.063 3.540 1.417 M5x0.8mm VS035 ST 3/4 - SFH 1/2 - 6.30 0.500 0.630 0.750 6.300 1.850 M10x1.0mm
VR024J HSK 100A - SFH 3/8C - 3.54 0.375 0.945 1.260 3.540 1.654 M8x1.0mm VS040 ST 1 - SFH 1/8 - 6.30 0.125 0.394 1.000 6.300 0.354 -
VR026J HSK 100A - SFH 3/8C - 6.30 0.375 0.945 1.260 6.300 1.654 M8x1.0mm VS041 ST 1 - SFH 3/16 - 6.30 0.188 0.394 1.000 6.300 0.472 -
VR028J HSK 100A - SFH 1/2C - 3.74 0.500 0.945 1.260 3.740 1.850 M10x1.0mm VS042 ST 1 - SFH 1/4 - 6.30 0.250 0.551 1.000 6.300 1.417 M5x0.8mm
VR030J HSK 100A - SFH 1/2C - 6.30 0.500 0.945 1.260 6.300 1.850 M10x1.0mm VS043 ST1 ST 1 - SFH 5/16 - 6.30 0.313 0.551 1.000 6.300 1.417 M6x1.0mm
VR032J HSK 100A - SFH 5/8C - 3.94 0.625 1.063 1.339 3.940 1.969 M12x1.0mm VS044 ST 1 - SFH 3/8 - 6.30 0.375 0.787 1.000 6.300 1.654 M8x1.0mm
VR034J 100A HSK 100A - SFH 5/8C - 6.30 0.625 1.063 1.339 6.300 1.969 M12x1.0mm VS045 ST 1 - SFH 1/2 - 6.30 0.500 0.787 1.000 6.300 1.850 M10x1.0mm
VR036J HSK 100A - SFH 3/4C - 4.13 0.750 1.299 1.654 4.130 2.047 M16x1.0mm VS046 ST 1 - SFH 5/8 - 6.30 0.625 0.866 1.000 6.300 1.929 M12x1.0mm
VR038J HSK 100A - SFH 3/4C - 6.30 0.750 1.299 1.654 6.300 2.047 M16x1.0mm VS050 ST 1 - 1/4 - SFH 1/8 - 6.30 0.125 0.394 1.250 6.300 0.354 -
VR040J HSK 100A - SFH 1C - 4.53 1.000 1.732 2.087 4.530 2.283 M16x1.0mm VS051 ST 1 - 1/4 - SFH 3/16 - 6.30 0.188 0.394 1.250 6.300 0.472 -
VR042J HSK 100A - SFH 1C - 6.30 1.000 1.732 2.087 6.300 2.283 M16x1.0mm VS052 ST 1 - 1/4 - SFH 1/4 - 6.30 0.250 0.551 1.250 6.300 1.417 M5x0.8mm
VR044J HSK 100A - SFH 1 1/4C - 4.72 1.250 1.732 2.087 4.720 2.283 M16x1.0mm VS053 ST1-1/4 ST 1 - 1/4 - SFH 5/16 - 6.30 0.313 0.551 1.250 6.300 1.417 M6x1.0mm
VR046J HSK 100A - SFH 1 1/4C - 6.30 1.250 1.732 2.087 6.300 2.283 M16x1.0mm VS054 ST 1 - 1/4 - SFH 3/8 - 6.30 0.375 0.945 1.250 6.300 1.654 M8x1.0mm
VS055 ST 1 - 1/4 - SFH 1/2 - 6.30 0.500 0.945 1.250 6.300 1.850 M10x1.0mm
* Effective cooling by coolant through cooling channel bores. VS056 ST 1 - 1/4 - SFH 5/8 - 6.30 0.625 1.063 1.250 6.300 1.929 M12x1.0mm
VS057 ST 1 - 1/4 - SFH 3/4 - 6.30 0.750 1.063 1.250 6.300 2.008 M16x1.0mm












1348 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1349

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic ST ST
Chuck SHRINK FIT EXTENSION SHRINK FIT EXTENSION







G L1 G L1


D2 d1 D1 D2 d1 D1

L L








METRIC (STANDARD) Unit : mm METRIC (EXTENDED) Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 G
VS010M ST12 - SFH3 - 120 3 8 12 120 10 - VS110M ST12 - SFH 3 - 160 3 8 12 160 10 -
VS011M 12 ST12 - SFH4 - 120 4 8 12 120 12 - VS111M 12 ST12 - SFH 4 - 160 4 8 12 160 12 -
VS012M ST12 - SFH5 - 120 5 10 12 120 15 - VS112M ST12 - SFH 5 - 160 5 10 12 160 15 -
VS013M ST12 - SFH6 - 120 6 10 12 120 36 M5×0.8 VS113M ST12 - SFH 6 - 160 6 10 12 160 36 M5×0.8
VS020M ST16 - SFH3 - 120 3 10 16 120 10 - VS210M ST16 - SFH 3 - 160 3 10 16 160 10 -
VS021M ST16 - SFH4 - 120 4 10 16 120 12 - VS211M ST16 - SFH 4 - 160 4 10 16 160 12 -
VS022M 16 ST16 - SFH5 - 120 5 10 16 120 15 - VS212M 16 ST16 - SFH 5 - 160 5 10 16 160 15 -
VS023M ST16 - SFH6 - 120 6 10 16 120 36 M5×0.8 VS213M ST16 - SFH 6 - 160 6 10 16 160 36 M5×0.8
VS024M ST16 - SFH8 - 120 8 12 16 120 36 M6×1.0 VS214M ST16 - SFH 8 - 160 8 12 16 160 36 M6×1.0
VS030M ST20 - SFH3 - 120 3 10 20 120 10 - VS310M ST20 - SFH 3 - 160 3 10 20 160 10 -
VS031M ST20 - SFH4 - 120 4 10 20 120 12 - VS311M ST20 - SFH 4 - 160 4 10 20 160 12 -
VS032M ST20 - SFH5 - 120 5 10 20 120 15 - VS312M ST20 - SFH 5 - 160 5 10 20 160 15 -
VS033M 20 ST20 - SFH6 - 120 6 10 20 120 36 M5×0.8 VS313M 20 ST20 - SFH 6 - 160 6 10 20 160 36 M5×0.8
VS034M ST20 - SFH8 - 120 8 12 20 120 36 M6×1.0 VS314M ST20 - SFH 8 - 160 8 12 20 160 36 M6×1.0
VS035M ST20 - SFH10 - 120 10 14 20 120 41.5 M8×1.0 VS315M ST20 - SFH 10 - 160 10 14 20 160 41.5 M8×1.0
VS036M ST20 - SFH12 - 120 12 16 20 120 46 M10×1.0 VS316M ST20 - SFH 12 - 160 12 16 20 160 46 M10×1.0
VS410M ST25 - SFH 3 - 160 3 10 25 160 10 -
VS411M ST25 - SFH 4 - 160 4 10 25 160 12 -
VS412M ST25 - SFH 5 - 160 5 15 25 160 15 -
VS413M ST25 - SFH 6 - 160 6 20 25 160 36 M5×0.8
VS414M 25 ST25 - SFH 8 - 160 8 20 25 160 36 M6×1.0
VS415M ST25 - SFH 10 - 160 10 20 25 160 41.5 M8×1.0
VS416M ST25 - SFH 12 - 160 12 20 25 160 46 M10×1.0
VS417M ST25 - SFH 14 - 160 14 20 25 160 46 M10×1.0
VS418M ST25 - SFH 16 - 160 16 22 25 160 49 M12×1.0
VS510M ST32 - SFH 6 - 160 6 20 32 160 36 M5×0.8
VS511M ST32 - SFH 8 - 160 8 20 32 160 36 M6×1.0
VS512M ST32 - SFH 10 - 160 10 24 32 160 41.5 M8×1.0
VS513M ST32 - SFH 12 - 160 12 24 32 160 46 M10×1.0
VS514M 32 ST32 - SFH 14 - 160 14 27 32 160 46 M10×1.0
VS515M ST32 - SFH 16 - 160 16 27 32 160 49 M12×1.0
VS516M ST32 - SFH 18 - 160 18 27 32 160 49 M12×1.0
VS517M ST32 - SFH 20 - 160 20 27 32 160 51 M16×1.0




1350 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1351

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



Hydraulic ST ST
Chuck SHRINK FIT EXTENSION SHRINK FIT EXTENSION







G L1 G L1


D2 d1 D1 D2 d1 D1

L L








METRIC (STANDARD) Unit : mm METRIC (EXTENDED) Unit : mm
EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 G EDP No. TAPER No. MODEL No. d1 D1 D2 L L1 G
VS010M ST12 - SFH3 - 120 3 8 12 120 10 - VS110M ST12 - SFH 3 - 160 3 8 12 160 10 -
VS011M 12 ST12 - SFH4 - 120 4 8 12 120 12 - VS111M 12 ST12 - SFH 4 - 160 4 8 12 160 12 -
VS012M ST12 - SFH5 - 120 5 10 12 120 15 - VS112M ST12 - SFH 5 - 160 5 10 12 160 15 -
VS013M ST12 - SFH6 - 120 6 10 12 120 36 M5×0.8 VS113M ST12 - SFH 6 - 160 6 10 12 160 36 M5×0.8
VS020M ST16 - SFH3 - 120 3 10 16 120 10 - VS210M ST16 - SFH 3 - 160 3 10 16 160 10 -
VS021M ST16 - SFH4 - 120 4 10 16 120 12 - VS211M ST16 - SFH 4 - 160 4 10 16 160 12 -
VS022M 16 ST16 - SFH5 - 120 5 10 16 120 15 - VS212M 16 ST16 - SFH 5 - 160 5 10 16 160 15 -
VS023M ST16 - SFH6 - 120 6 10 16 120 36 M5×0.8 VS213M ST16 - SFH 6 - 160 6 10 16 160 36 M5×0.8
VS024M ST16 - SFH8 - 120 8 12 16 120 36 M6×1.0 VS214M ST16 - SFH 8 - 160 8 12 16 160 36 M6×1.0
VS030M ST20 - SFH3 - 120 3 10 20 120 10 - VS310M ST20 - SFH 3 - 160 3 10 20 160 10 -
VS031M ST20 - SFH4 - 120 4 10 20 120 12 - VS311M ST20 - SFH 4 - 160 4 10 20 160 12 -
VS032M ST20 - SFH5 - 120 5 10 20 120 15 - VS312M ST20 - SFH 5 - 160 5 10 20 160 15 -
VS033M 20 ST20 - SFH6 - 120 6 10 20 120 36 M5×0.8 VS313M 20 ST20 - SFH 6 - 160 6 10 20 160 36 M5×0.8
VS034M ST20 - SFH8 - 120 8 12 20 120 36 M6×1.0 VS314M ST20 - SFH 8 - 160 8 12 20 160 36 M6×1.0
VS035M ST20 - SFH10 - 120 10 14 20 120 41.5 M8×1.0 VS315M ST20 - SFH 10 - 160 10 14 20 160 41.5 M8×1.0
VS036M ST20 - SFH12 - 120 12 16 20 120 46 M10×1.0 VS316M ST20 - SFH 12 - 160 12 16 20 160 46 M10×1.0
VS410M ST25 - SFH 3 - 160 3 10 25 160 10 -
VS411M ST25 - SFH 4 - 160 4 10 25 160 12 -
VS412M ST25 - SFH 5 - 160 5 15 25 160 15 -
VS413M ST25 - SFH 6 - 160 6 20 25 160 36 M5×0.8
VS414M 25 ST25 - SFH 8 - 160 8 20 25 160 36 M6×1.0
VS415M ST25 - SFH 10 - 160 10 20 25 160 41.5 M8×1.0
VS416M ST25 - SFH 12 - 160 12 20 25 160 46 M10×1.0
VS417M ST25 - SFH 14 - 160 14 20 25 160 46 M10×1.0
VS418M ST25 - SFH 16 - 160 16 22 25 160 49 M12×1.0
VS510M ST32 - SFH 6 - 160 6 20 32 160 36 M5×0.8
VS511M ST32 - SFH 8 - 160 8 20 32 160 36 M6×1.0
VS512M ST32 - SFH 10 - 160 10 24 32 160 41.5 M8×1.0
VS513M ST32 - SFH 12 - 160 12 24 32 160 46 M10×1.0
VS514M 32 ST32 - SFH 14 - 160 14 27 32 160 46 M10×1.0
VS515M ST32 - SFH 16 - 160 16 27 32 160 49 M12×1.0
VS516M ST32 - SFH 18 - 160 18 27 32 160 49 M12×1.0
VS517M ST32 - SFH 20 - 160 20 27 32 160 51 M16×1.0




1350 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1351

ROTARY ROTARY
TOOL HOLDERS TOOL HOLDERS



END MILL HOLDER CAT END MILL HOLDER CAT




B



d D
AD d D



TAPER No. L TAPER No. B L



Taper Coolant Taper Coolant
ASME B5.50 Accuracy G Value RPM System ASME B5.50 Accuracy G Value RPM System
ASME B5.50-2009-CAT - CAT AT3 6.3 15,000 AD ASME B5.50-2009-CAT - CAT AT3 6.3 15,000 AD/B
STUB Unit : inch STANDARD Unit : inch
EDP No. TAPER No. MODEL No. d D L EDP No. TAPER No. MODEL No. d D L
AK206 CAT40 - EMH 1/2 - 1.75 0.500 1.25 1.75 AK000B CAT40 AD/B - EMH 1/8 - 2.50 0.125 0.69 2.50
AK208 CAT40 - EMH 5/8 - 1.75 0.625 1.50 1.75 AK001B CAT40 AD/B - EMH 3/16 - 2.50 0.187 0.69 2.50
AK210 40 CAT40 - EMH 3/4 - 1.75 0.750 1.75 1.75 AK002B CAT40 AD/B - EMH 1/4 - 2.50 0.250 0.78 2.50
AK214 CAT40 - EMH 1" - 1.75 1.000 1.75 1.75 AK003B CAT40 AD/B - EMH 5/16 - 2.50 0.312 0.88 2.50
AK217 CAT40 - EMH 1 1/4 - 2.00 1.250 2.25 2.00 AK004B CAT40 AD/B - EMH 3/8 - 2.50 0.375 1.00 2.50
AK005B CAT40 AD/B - EMH 7/16 - 2.50 0.437 1.13 2.50
* High balanced End Mill Holders on page 1356~1357. AK006B 40 CAT40 AD/B - EMH 1/2 - 2.63 0.500 1.25 2.63
* Set screws for End Mill Holders on page 1365.
AK008B CAT40 AD/B - EMH 5/8 - 3.75 0.625 1.50 3.75
AK010B CAT40 AD/B - EMH 3/4 - 3.75 0.750 1.75 3.75
AK012B CAT40 AD/B - EMH 7/8 - 4.00 0.875 1.88 4.00
AK014B CAT40 AD/B - EMH 1" - 4.00 1.000 2.00 4.00
AK017B CAT40 AD/B - EMH 1 1/4 - 4.25 1.250 2.50 4.25
AK021B CAT40 AD/B - EMH 1 1/2 - 4.63 1.500 2.50 4.63
AL002B CAT50 AD/B - EMH 1/4 - 2.50 0.250 0.78 2.50
AL003B CAT50 AD/B - EMH 5/16 - 2.50 0.312 0.88 2.50
AL004B CAT50 AD/B - EMH 3/8 - 2.50 0.375 1.00 2.50
AL005B CAT50 AD/B - EMH 7/16 - 2.63 0.437 1.13 2.63
AL006B CAT50 AD/B - EMH 1/2 - 2.63 0.500 1.25 2.63
AL008B 50 CAT50 AD/B - EMH 5/8 - 3.75 0.625 1.50 3.75
AL010B CAT50 AD/B - EMH 3/4 - 3.75 0.750 1.75 3.75
AL012B CAT50 AD/B - EMH 7/8 - 3.75 0.875 1.88 3.75
AL014B CAT50 AD/B - EMH 1" - 4.00 1.000 2.00 4.00
AL017B CAT50 AD/B - EMH 1 1/4 - 4.00 1.250 2.50 4.00
AL021B CAT50 AD/B - EMH 1 1/2 - 4.00 1.500 2.50 4.00
AL029B CAT50 AD/B - EMH 2" - 5.63 2.000 3.75 5.63
* High balanced End Mill Holders are available on request.
* Set screws for End Mill Holders on page 1365.












1352 • phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com phone:+1-800-765-8665, Technical Support : 888-868-5988, www.yg1usa.com • 1353