CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161 EQUIPMENT ...

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

1 SECTION-1 - GENERAL EQUIPMENT SPECIFICATIONS:
2
3 SPECIFICATION OUTLINE:
4 The following specifications for a 6 wheel flat bed truck with dual 2000 lb vertical mounted
5 thermoplastic heating kettles are divided into four complete sections. The first section outlines the
6 overall specification requirement. The second details the chassis portion of the truck. The third
7 section refers to mostly the flatbed that is to be mounted onto the truck chassis. The fourth
8 outlines the dual 2000 lb vertical mounted, oil jacketed premelter heating kettles that is to be
9 mounted on the truck bed. The truck shall be delivered complete with all equipment and
10 accessories necessary for safe and efficient operation, ready for immediate job site operation
11 within the City of San Francisco. The unit shall comply with the manufacturer’s current model
12 truck chassis/body, with additions and deletions as contained herein.
13
14 MANUFACTURING, MATERIAL AND DESIGN PRACTICES:
15 It is intended that the manufacturer, in the selection of components will use material and design
16 practices that are the best available in the industry for the type of operating conditions to which the
17 unit will be subjected. Engine, suspension, wheels, tires and other component parts shall be
18 selected to address the performance requirements of this specification. All parts, equipment and
19 accessories shall conform in strength, quality of material and workmanship to recognized industry
20 standards.
21
22 HEAVY DUTY TERMINOLOGY DEFINED:
23 The term “heavy duty” as used in these specifications shall mean that the item to which the term is
24 applied shall exceed the usual quantity, quality or capacity supplied with standard production
25 unit(s) and it shall be able to withstand unusual strain, exposure, temperature, wear and use.
26
27 ALTERNATES:
28 When the specific name of a manufacturer, brand or make, with or without model number, is used
29 in describing any item in this specification, bids for similar articles will be considered unless
30 otherwise stated. Bidders may also propose items of equivalent features or manufacturer’s
31 updated part or part number. Purchasing shall be the sole judge as to whether such alternate
32 articles are acceptable. Unless bidder states to the contrary, articles offered will be assumed to
33 be the specific article named in this specification. If not offering the specific article named, bidder
34 must enclose with its bid full information, specifications and descriptive data on alternate items
35 offered. Purchasing reserves the right to permit deviations from the specifications if any article
36 offered is substantially in accord with Purchasing’s specifications and is deemed by Purchasing to
37 be of as good quality and as fully satisfactory for its intended use, Bidder is responsible for
38 identifying any devi AMations from Purchasing’s specifications. Bidders should not assume an
39 alternate offered is an approved equal. The City will evaluate the alternate and inform the bidder if
40 the alternate is
41
42

Page 1 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

43 CONDITIONAL MODIFICATIONS:
44 Potential variances of a specific truck manufacturer’s chassis may require variances in the flat bed

45 body mounting and design to some degree. Therefore, bidders shall clearly and completely

46 outline all areas needing such modifications.

47
48 GENERALITIES:
49 To allow for manufacture’s specific designs, and insure a level of competitiveness, we have left

50 certain areas of our specifications general by design. In such cases, the items being referred to

51 may be general, but adherence to the requested end product and /or result must be met. This is

52 especially important in areas where critical dimensions, capacities, grades of steel, etc. are

53 specified. In the cases were the word SHALL is used, no substitution will be allowed.

54

55 IMPORTANT: PRE-BID CONFERENCE

56 Because of the variances in the truck chassis that may be bid, it may be necessary to vary the bed

57 dimensions and design to some degree.

58

59 A Pre-bid Conference will be held as follows:

60

61 DATE: June 15, 2012

62 TIME: 9 AM

63 PLACE: City & County of San Francisco

64 Central Shops

65 1800 Jerrold Avenue

66 San Francisco, CA

67

68 Though not mandatory, attendance at the conference is strongly urged for all

69 prospective bidders on this contract.

70
71 It is requested that bidder’s questions concerning this Contract Proposal be

72 submitted by mail or Fax at least 72 hours prior to the date and time of the Pre-bid

73 Conference and directed to:

74

75 Paul Hootman Phone: (415) 701-4706

76 Department OCA FAX: (415) 701-5676

77 Purchasing Division

78 1 Dr. Carlton B. Goodlett Place

79 San Francisco, CA 94102

80

81

82 Please reference Bid Proposal No. ITSF12000929

83

Page 2 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

84 The Pre-bid Conference will begin at the time specified, and company representatives are
85 urged to arrive on time. Topics already covered will not be repeated for the benefit of late
86 arrivals. Failure to attend the Pre-bid Conference shall not excuse the successful bidder
87 from any obligations of the contract. Any change or addition to the requirements
88 contained in this Contract Proposal as a result of the Pre-Bid Conference will be executed
89 by written Change Notice.
90
91 MANUFACTURER’S SPECIFICATION:
92 Complete manufacturer’s specification, published literature and photos or illustrations of unit
93 proposed, should be furnished with bid. Only new models in current production that are
94 catalogued by the manufacturer and for which printed literature and specifications are available
95 will be accepted. Bidders shall prepare and submit their own proposals addressing each section,
96 item or component of these specifications, indicating full compliance without exception, or
97 explaining in detail any exception, deviation or non-compliance. Bidders should not simply submit
98 a copy of these specifications as their proposal nor should they submit copies of manufacturer or
99 third party quotations as a response to the City’s bid solicitation.
100
101 MANUFACTURER'S STANDARD EQUIPMENT:
102 All equipment and components listed as standard by the manufacturer for model quoted shall be
103 furnished whether or not such items are detailed herein, e.g., special wrenches, tool kits, etc.
104 Optional equipment as necessary to meet the following requirements of this specification shall
105 also be supplied. Should the requirements as specified not comply, the manufacturer is required
106 to re-figure and revise the specifications to meet all laws, rules and regulations where it applies to
107 items such as the ratings of axles, tires, rims, brakes, batteries, cooling capacity, etc. and the City
108 of San Francisco is to be notified thereof.
109
110 APPLICABLE DOCUMENTS AND CERTIFICATIONS:
111 Specifications on the following pages are written with the intent to comply with all applicable
112 documents and certifications, but the final responsibility to comply shall rest with the vendor and
113 not the City of San Francisco. The successful bidder shall adhere to the standards set forth by the
114 following agencies:
115
116  Federal Motor Vehicle Safety Standard, Department of Transportation.
117  State of California Motor Vehicle Code.
118  State of California General Industrial Safety Orders.
119  State of California Health and Safety Code, Motor Vehicle Pollution Control.
120  California Occupational Safety and Health Act (OSHA) and the EPA
121  Society of Automotive Engineering Standards.
122  American Society of Mechanical Engineers (ASME).
123  American National Safety Institute (ANSI)
124  Vehicle must be compliant with California Administrative Code (C.A.C.) Title 13.

Page 3 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

125 DEMONSTRATIONS
126 The City reserves the option to request, and the bidder shall agree to provide, an “on the job
127 demonstration and evaluation” for the City’s Fleet Management personnel before acceptance of
128 contract in the event performance of unit proposed is not familiar to the City. If requested by the
129 City, a demonstrator unit shall be made available prior to award and provided at no additional cost
130 to the City. Time and amount of hours required for such evaluation shall be as determined by the
131 City.
132
133 OPERATIONAL NOISE STANDARD:
134 Noise level shall be in conformance with standards established by Local, State and Federal
135 Agencies. City personnel for noise requirements may test each unit delivered before the unit is
136 accepted.
137
138 HOSE AND WIRING ROUTING, HARDWARE REQUIREMENTS:
139 All hoses and wiring shall have adequate protective covers wherever there is a possibility of
140 contact with any other components. Separators shall be used where applicable. No tape or
141 adhesive fasteners will be accepted. All hoses, wiring and pipes shall be routed to be clear of all
142 heat sources and shall be protected from any present or potential source of snags, abrasions or
143 sharp edges. If any wiring for any lamps are routed through any tool compartment or canopy,
144 these wires shall be enclosed in steel. All fasteners (nuts, bolts, rivets & etc.) shall be grade 5 or
145 better with a rust inhibiting coating. Several applications must have grade 8.
146
147 SWITCHES, LABELS & HARDWARE:
148 All toggle and push button switches shall be marine type with additional rubber boots. All controls,
149 warning gauges and valves shall be marked as to function with stamped or engraved stainless
150 steel or aluminum labels. These labels shall be attached by aluminum and/or stainless steel
151 rivets. All hardware and fasteners shall be grade 8 or better except as specified.
152
153 DELIVERY REQUIREMENTS:
154 Due to the fabrication design required on the body of this truck, we understand the potential for
155 build schedule delays. For this truck, we are setting the delivery schedule at not more than 180
156 days, or 6 months. This unit should be delivered and be ready for service within the stated time
157 range. If a truck being bid meets all other requirements of the specification, but cannot meet the
158 specified time allotted for delivery, this discrepancy shall be stated upon the bid return.
159
160 WELDING:
161 All welding shall be continuous where applicable. All welding shall be performed in accordance
162 with the applicable requirements of the latest codes, rules or specifications of the American
163 Welding Society, (AWS), and the requirements of these specifications and special provisions, and
164 shall be subject to the test and examinations therein specified.
165

Page 4 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

166 INSPECTION TRIPS (include in specs if applicable)
167 Bid price should include airfare (if over 125 miles from San Francisco), meals and lodging for 2
168 factory inspection trips for 2 City representatives. The inspection trips shall be scheduled at times
169 mutually agreed upon between the awarded bidder and the City representatives and should be for
170 a minimum 3 days. Meals and lodging rate shall comply with the current Federal Rates for the
171 Continental U.S.A. The rates are available from the following website:
172
173 www.gsa.gov/perdiem
174
175 The first inspection trip, known as the “pre-paint” or mid-inspection will be arranged at a time when
176 the vehicle is assembled with major components installed and before final paint work is begun. If
177 the inspection discloses any deviation from the specifications, the discrepancies, if minor can be
178 corrected while City inspectors remain at the plant. If the problem is not readily correctable, the
179 inspectors can return for inspection at a mutually agreed time, at the expense of the awarded
180 bidder.
181
182 The second inspection trip will be the final factory inspection of the completed vehicle completely
183 finished and ready for delivery. Workmanship and finish will be inspected and the vehicle will be
184 road tested and equipment operated before final delivery. If the inspection discloses any deviation
185 from the specifications, the discrepancies, if minor can be corrected while City inspectors remain
186 at the plant. If the problem is not readily correctable, the inspectors can return for inspection at a
187 mutually agreed time, at the expense of the awarded bidder.
188
189 PRE-CONSTRUCTION REQUIREMENT:
190 The successful bidder shall be required to attend a pre-construction meeting with the initiators of
191 these specifications and /or designated City representative(s) within 30 calendar days prior to the
192 start of any Body construction. Weekly update photographs (Digital Format) may be required of
193 the vendor if requested. The purpose is to ensure the proper interpretation of the City’s written
194 specifications. If necessary, the vendor may also be required to coordinate any additional
195 meetings prior to the installation of equipment, painting, etc. The location of these meetings
196 should be at 1800 Jerrold Ave, San Francisco California 94124. Vendor may contact Tony
197 Pastrano at 415-550-4604 for information and instructions.
198
199 CONTRACT AMENDMENT:
200 Any proposed changes in this specification must be submitted in writing to the Purchaser for
201 approval prior to implementation. Any work performed prior to approval will be done at the risk of
202 the vendor and acceptance of the vehicle will be delayed and payment withheld. A written
203 amendment to contract will be issued by the City.
204
205
206

Page 5 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

207 BIDDER’S COMPLIANCE AND EXCEPTIONS:
208 All exceptions shall be stated no matter how seemingly minor. Bidders shall indicate
209 compliance with each section and line item specifications as required, in the line spaces
210 provided by marking with a “Y” for yes. If the bidder is offering an alternate of equal or
211 superior status to the line item specification, bidder will indicate by marking with an “E” for
212 exception on each line item. The bidder must then reference each item exception and
213 explain the exception taken and the proposed alternate on Attachment D, Bid Exception
214 Sheets.
215
216 **Bids, which do not include confirmation of each section and line item, as required, will be
217 deemed to take exception to such bid requirements, which may result in the bid being
218 deemed non-responsive. If exceptions are taken, Attachment D, Bid Exception Sheets
219 must be returned with the submitted bids.
220
221 IMPORTANT: If a single vendor is submitting multiple bids, the vendor shall submit a
222 completed set of specs for each individual bid. Multiple bids that are submitted as one bid
223 package will not be acceptable.
224
225 SECTION 2-CHASSIS:
226 The 6 wheel flatbed truck chassis with two (2) 2000 lb thermoplastic containers to be furnished
227 under these specifications shall be a basic fleet model and be listed as the manufacture’s current
228 model. The truck must comply with standard specifications for the model offered with exceptions
229 and additions as contained herein.
230
231 GENERAL SERVICE:
232 _____2013 International model # 4300 SBA 4 x 2 or approved equal.
233 _____Truck configuration: Flatbed stake body with thermoplastic kettles.
234 _____100 % highway and city terrain.
235 _____Maximum grade 20%.
236 _____2 axle cab and chassis.
237 _____25,999 lb GVWR.
238 _____Front axle to be rated @ 12,000 lbs.
239 _____Rear axle to be rated @ 21,000 lbs.
240 _____WB shall be approximately 175”. Exact dimensions shall be determined on the
241 collaboration between the truck manufacturer & body manufacturer.
242 _____CA shall be approximately 108”. Exact dimensions shall be determined on the
243 collaboration between the truck manufacturer & body manufacturer.
244 _____AF shall be approximately 63”. Exact dimensions shall be determined on the
245 collaboration between the truck manufacturer & body manufacturer.
246 _____Four (4) extra set of keys.
247 NOTE: Vehicle shall not exceed 26,000 GVWR rating.

Page 6 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

248 ENGINE & EQUIPMENT:
249 _____International DT466 High Torque, turbo charged, 50 state compliant or approved equal.
250 _____245 HP, 660 lb-ft torque @ 1300 RPM, 2400 RPM governed speed. This engine shall be
251 Bio-Diesel B20 compatible.
252 _____This engine shall be certified to meet ARB’s .01 grams/brake horsepower-
253 hour (g/bhp/hr) particulate matter (PM) emission standard.
254 _____This engine shall be certified to the California or 50 State 2010 exhaust
255 emission standards.
256 _____Electronic data link connector for vehicle programming and diagnostic in cab.
257 _____The engine shall be programmed to shut down after a five minute idle time.
258 _____This time limit shall be overridden to allow the engine to run for an unlimited time
259 while the PTO is engaged. If the users, in the future, wish to change this time
260 parameter, the engine must be capable of accepting the programming change.
261 _____Fuel/water separator and fuel filter in a single assembly, mounted on engine.
262 _____Fuel Lines: Nylon tubing with o-ring snap-on quick-connect fittings at both ends.
263 _____Alternator should be a Leece Neville brush type with a minimum of 160 amps, 12 volts,
264 self excite and pad mounted.
265 _____Two (2) maintenance free batteries, threaded type terminals with a minimum total of
266 1850 Cold Cranking Amps.
267 _____Remote mounted jump start stud.
268 _____Batteries shall be in a steel box with plastic cover.
269 _____Delco Remy 12V starter, model number # 39MT, gear reduced, weather pack silicone
270 sealed with thermal over-crank protection.
271 _____Heaviest factory battery cables available. All connections shall be Weather-Pak.
272 _____Under hood Dual Element Air Filter with air cleaner restriction gauge.
273 _____Magnetic engine oil drain plug.
274 _____Engine start and shut down key operated.
275 _____Engine oil filter-cartridge type.
276 _____All wiring to be Weather-Pak.
277 _____High efficiency cooling system, heaviest-duty radiator available with extended life
278 coolant.
279 _____Horton fan clutch.
280 _____Coolant system shall have Ethylene Propylene Diene Monomer radiator and heater hoses
281 with anti-rust type heater and radiator hose clamps.
282 _____Fan drive special effects fan cooling ring with fan shroud effects, engine mounted.
283 _____Low coolant level sensor with audible alarm.
284 _____Single 5” horizontal exhaust system with Catalytic Converter, short tail pipe, frame
285 mounted on the right side. Any exposed exhaust pipe that has the potential to come into
286 contact with personnel or other areas of the truck shall be covered by a heat shield.
287
288

Page 7 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

289 _____Engine shall be programmed to shut down in the event of high temp, low oil pressure or
290 low coolant level. There shall be a manual or electronic override for the shut down system
291 that will allow for moving the vehicle out of hazardous situations.
292 _____6 factory switches in instrument panel (2-position switches), one power module with 6
293 channels, 20 amp per channel and 80 max output.
294 _____Switches control the power modules through multiplex wiring, mounted under cab at battery
295 box.
296 _____Factory switches (Such as the Diamond Logic System) shall be used to control auxiliary
297 lighting, mounted accessories, and PTO. Switches shall be clearly labeled as to functions.
298 _____Backlighting shall have two (2) levels of intensity. The low-level lights shall be activated
299 when the ignition is turned on. The high-level lights shall be activated when the
300 individual switch is turned. Note: Switches shall be mounted within easy reach of the
301 driver/operator.
302 NOTE: See attached diagram for layout specifics.
303
304 TRANSMISSION:
305 _____Allison transmission, model 2500 RDS automatic transmission, 6 speed with overdrive and
306 PTO provisions with 33,000 –lb GVW & GCW max.
307 _____Allison approved rebuildable transmission oil cooler. This cooler shall be the largest
308 available.
309 _____Oil fill tube, dipstick with level sensor.
310 _____T- Handle shift control dash mounted
311 _____Heavy-duty Spicer 1710 half round main driveshaft.
312 _____Spin off/on type transmission oil filter.
313 _____TranSynd synthetic automatic transmission fluid.
314 _____Electronic transmission customer access connector.
315 _____Magnet in transmission oil pan.
316
317 BRAKES:
318 _____Gear driven air compressor with a minimum 16.5 CFM.
319 _____Formed copper compressor discharged discharge hose.
320 _____Meritor System Saver 1200 air dryer
321 _____Spin on/off desiccant cartridge..
322 _____Wet tank drain valve – Bendix – 2 automatic.
323 _____Steel air tanks tandem axle mounted below battery box.
324 _____Bendix ABS brake control system.
325 _____Four chamber Haldex parking brakes, chassis park brake system.
326 _____Color coded nylon brake lines.
327 _____Data link for diagnosing ABS system.
328 _____Alarm parking brakes, electric horn sounds in repetitive manner when vehicle park brake
329 is not set with ignition off and any door opened.

Page 8 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

330 _____Parking brake valve, color coded yellow knob, located on instrument panel.
331
332 FRONT BRAKES:
333 _____15.0” x 4.0” air cam brakes with 20 sq. in. Haldex long stroke brake chambers.
334 _____ABS type Bendix air brakes with dust covers and automatic slack adjusters.
335
336 REAR BRAKES:
337 _____16.5” X 7.0” air cam rear brakes with Haldex GC3030LHDHO long stroke brake chambers
338 and heavy-duty spring actuated parking brakes.
339 _____Cast iron rear brake drums with dust shields.
340 _____ABS type air brakes with automatic slack adjusters, tandem axles.
341
342 FRONT AXLE:
343 _____Non-driving front axle, I-Beam type with 12,000 lbs capacity.
344 _____Front suspension should be a spring parabolic, taper leaf, 12,000 lbs capacity.
345 _____Oil lubricated front oil seals with wheel bearings.
346 _____Heavy-duty shock absorbers.
347 _____Heavy-duty steering gear, Sheppard M-100, power steering or equal.
348 _____Maintenance free front spring pin bushings.
349 _____Visible capacity oil seal caps, Dana Spicer Outrunner oil seals, petroleum based lubricant in
350 hubs.
351
352 REAR AXLE:
353 _____Single rear axle, Meritor RS-21-160 single reduction, 21,000-lb capacity and
354 200 wheel ends.
355 _____Gear ratio-5.63.
356 _____Magnetic drain valve.
357 _____Rear vari-rat spring suspension, 23,500-lb capacity with 4,500 auxiliary rubber
358 spring.
359 _____Two heavy-duty shock absorbers.
360 _____Petroleum base lubricant.
361
362 FRONT TIRES & WHEELS:
363 _____Two (2) 11R x 22.5 G287 MSA (Goodyear), load range G, 14 ply front tires.
364 _____Two (2)22.5” x 8.25 hub piloted, 10 stud, flanged nut, metric mount with steel hubs front
365 steel wheels.
366 _____One spare tire and wheel, mounted and delivered loose. Same type and rating.
367
368 REAR TIRES & WHEELS:
369 _____Four (4) 11R x 22.5 G287 MSA (Goodyear), load range G, 14 ply rear tires.
370 _____Four (4) hub piloted, 10 stud, flanged nut, metric mount with steel hubs steel wheels.

Page 9 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

371 CHASSIS:
372 _____Wheelbase for chassis in accordance with body manufacturer requirements.
373 _____Frame rails heat treated alloy steel, 120,000 psi yield: 10.125” x 3.580” x 0.312”; 420”
374 maximum OAL.
375 _____Two (2) front tow hooks, mounted inside frame rails.
376 _____Full width front steel bumper powder coated gray.
377
378 FUEL TANK:
379 _____One 100 U.S. gallon aluminum tank with step(s).
380 _____The tank shall have over tank mounting brackets.
381 _____Tank shall be mounted left side under cab.
382 _____The fuel tank shall be modified to supply fuel to the auxiliary engine and thermoplastic
383 kettles.
384
385 CAB:
386 _____Conventional steel cab with tilting forward fiberglass hood.
387 _____Cab shall be insulated throughout.
388 _____All window glass to be tinted.
389 _____Rear visibility window.
390 _____Interior grab handle, “A” pillar mounted, passenger side.
391 _____Interior grab handle, “B” pillar mounted, driver side.
392 _____Cab shall be equipped with heavy duty exterior full length grab handles, stainless steel,
393 one on each side.
394 _____Two (2) steps per door.
395 _____Interior lights with manual control and door switch.
396 _____The rear stop/turn/running lights shall be Truck-Lite brand LED.
397 _____The rear back-up lights shall be Truck-Lite brand LED.
398 _____Air seat; National 2000 air suspension with dual shocks, high back with integral headrest,
399 heavy duty vinyl, isolated, with 2 position front cushion adjustment, -3 to +14 degree seat
400 back adjustment, single chamber air lumbar support, black or gray in color.
401 _____Passenger seat shall be a bench type seat for two persons with three point seat belts on out
402 side seating and a lap belt for the center seat position with under seat storage compartment
403 Heavy-duty vinyl, black or gray in color.
404 _____3-point lap and shoulder seat belts.
405 _____Chrome grille.
406 _____Dual trumpet air horn mounted behind bumper or right rail.
407 _____Down view mirror over passenger door.
408 _____(2) Lang Mekra style mirrors, rectangular, 7.44” x 14.84”, breakaway brackets with 102”
409 side spacing, integral convex mirrors both sides. All heated heads, thermostatically
410 controlled with clearance lights, and shall be motorized which shall be controlled from a
411 labeled switch inside cab.

Page 10 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

412 _____Door mounted left and right arm rest.
413 _____Air conditioner with integral heater and defroster.
414 _____Door molded storage pockets, mounted both the passenger and driver’s door.
415 _____Door trim panels, molded plastic driver and passenger side.
416 _____Headliner, printed cloth.
417 _____Cab interior deluxe, dark gray in color.
418 _____Cab interior trim panels, molded plastic, full height; All exposed interior sheet metal to
419 be covered. Dark gray in color.
420 _____Overhead console with dual storage area and retainer nets.
421 _____Passenger and driver sun visor
422 _____”A” & “B” pillar cover molded plastic, dark gray in color.
423 _____Coat hook located on rear wall, centered above rear window.
424 _____Manual reset circuit breakers, SAE type III with trip indicators except for 5-amp fuses.
425 _____Two (2) courtesy lights under instrument panel.
426 _____Map light, integral to dome light mounted on overhead console.
427 _____AM/FM radio with CD player, clock, digital display with 2 speakers.
428 _____Two (2) electric horns.
429 _____Two (2) power source, cigar type receptacles without plug and cord.
430 _____Two (2) speed windshield wipers with intermittent option, integral with turn signal switch.
431 _____When windshield wipers are turned on headlights should automatically come on.
432 _____Windshield wipers shall be forced to slowest intermittent speed when parking brake applied
433 for more than 60 seconds.
434 _____Standard windshield washer reservoir with washer fluid indicator.
435 _____Turn signal switch, self-canceling, headlight dimmer, flash-to-pass feature, and
436 emergency flashers.
437 _____Halogen headlights, composite aero design for two light system including daytime
438 running lights.
439 _____Five (5) clearance/marker lights, Amber LED, flush mounted on cab.
440 _____Tilt and telescoping steering column.
441 _____Two (2) spoke, 18” diameter steering wheel.
442 _____Black rubber floor covering material over insulation with OEM rubber floor mats. No
443 carpet will be acceptable.
444 _____6 factory switches in instrument panel (2-position switches), one power module with 12
445 channels, 20 amp per channel and 80 max output.
446 _____Switches control the power modules through multiplex wiring, mounted at rear of frame.
447 _____Factory switches (Diamond Logic) shall be used to control auxiliary lighting (emergency)
448 and mounted accessories. Switches shall be clearly labeled as to functions.
449 _____Back lighting shall have two (2) levels of intensity. The low-level shall be activated
450 when the ignition is turned on. The high level lights shall be activated when the
451 individual switch is turned on.
452 NOTE: See attached diagram for layout specifics.

Page 11 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # 15800161

EQUIPMENT SPECIFICATIONS FOR
A THERMOPLASTIC SERVICE TRUCK

06/11/2012

453 INSTRUMENTS:
454 _____Low air light and buzzer.
455 _____Coolant temperature gauge.
456 _____Engine oil temperature gauge.
457 _____Dual air pressure gauge.
458 _____Fuel level gauge.
459 _____Voltmeter gauge.
460 _____Electric speedometer.
461 _____Electric tachometer gauge.
462 _____Engine hour gauge.
463 _____Transmission temperature gauge.
464 _____Manual reset circuit breakers, most circuits.
465 _____Warning system (visual and audible) low fuel, low oil pressure, high engine coolant
466 temp., and low battery voltage.
467
468 PAINT:
469 _____Before painting, cab and body shall be cleaned of al mill scales, rust, dirt, oil, and
470 grease, painted with a rust inhibitor primer and finished with a base coat/clear coat paint,
471 the brightest white available.
472 _____Entire understructure shall be under sealed with heavy-duty under-sealer.
473
474 WARRANTY:
475 _____Basic vehicle warranty shall be 2 years unlimited miles, 100% parts and labor.
476 _____Engine shall be warranted for 3 years or 150,000 miles, 100% parts and labor.
477 _____Automatic transmission shall be warranted for a period of 5 years or 150,000 miles,
478 100% parts and labor.
479 _____All warranties shall commence when the City accepts the vehicle. Delivering the
480 vehicle does not constitute acceptance by the City.
481
482 MANUALS:
483 _____Two complete set of parts, service, and repair manuals for engine, transmission,
484 differential, body electric and electronic components. CD or hard copy form is
485 acceptable.
486
487
488
489
490
491
492
493

Page 12 of 25