The words you are searching are inside this book. To get more targeted content, please make full-text search by clicking here.

Jim's Supply Steel Service Center Catalog - Revised 03.2016

Discover the best professional documents and content resources in AnyFlip Document Base.
Search
Published by Jim's Supply Company, Inc., 2016-04-01 18:07:57

Steel Service Center

Jim's Supply Steel Service Center Catalog - Revised 03.2016

Keywords: steel service center,jim's supply,pipe,tubing,metal

Table of Contents

Shapes and Sizes
Round, Square, & Hexagon Bars..........................................................................................................2
Hot Rolled Strip ........................................................................................................................................4
Flats ..............................................................................................................................................................5
Universal Mill Plates..............................................................................................................................12
Sheets........................................................................................................................................................13
Cold Rolled Sheets ...............................................................................................................................15
Plates .........................................................................................................................................................16
Galvanized Sheets.................................................................................................................................17
Floor Plate................................................................................................................................................18
Bar Angles................................................................................................................................................19
Structural Angles ..................................................................................................................................20
Bar Size Channels ..................................................................................................................................22
Structural Channels .............................................................................................................................22
Jr. Channels .............................................................................................................................................23
Ship & Car Channels..............................................................................................................................23
Wide Flange Beams..............................................................................................................................23
I Beams......................................................................................................................................................27
Jr. Beams ..................................................................................................................................................28
Pipe Dimensions....................................................................................................................................29
Gauge Pipe..............................................................................................................................................29
ANSI Pipe Schedule...............................................................................................................................30
Gauge Pipe Schedule...........................................................................................................................32
PG & E Barrier Posts ..............................................................................................................................33
Square Tubing .......................................................................................................................................34
Rectangular Tubing..............................................................................................................................35
Tul Bar........................................................................................................................................................38
Concrete Reinforcing Bars..................................................................................................................38
Welded Wire Mesh Fabric ..................................................................................................................38
Ladder Rungs .........................................................................................................................................38
Expanded Metal.....................................................................................................................................39
Grip Strut..................................................................................................................................................40

General Information
Hot Rolled Products..............................................................................................................................41
Special Quality Bar Products..............................................................................................................42
Sheet Products.......................................................................................................................................45
Plate Products.........................................................................................................................................46
Structural Shapes ..................................................................................................................................52
Pipe Products .........................................................................................................................................53
Concrete Reinforcing Bars .................................................................................................................54
Expanded Metal............................................................................................................................................55

Formulas ....................................................................................................................................................................57
Conversion Table ....................................................................................................................................................57

Disclaimer: The weights listed in this catalog may vary depending on producing 1
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
Inc. cannot be held liable for any inaccuracies.

WEIGHTS OF ROUND, SQUARE, AND HEXAGON BARS
POUNDS PER FOOT

WEIGH Size Rounds Squares Hexagons Wt/20’ Bar
Inches 0.003 0.003 0.003 Rounds Only
1/32 0.010 0.013 0.012 -
1/16 0.024 0.030 0.026 -
3/32 0.042 0.053 0.046 -
1/8 0.065 0.083 0.072 -
5/32 0.094 0.120 0.104 -
3/16 0.128 0.163 0.141 1.88
7/32 0.167 0.213 0.184 -
1/4 0.211 0.269 0.233 3.34
9/32 0.261 0.332 0.288 -
5/16 0.316 0.402 0.348 5.22
11/32 0.376 0.478 0.414 -
3/8 0.441 0.561 0.486 7.52
13/32 0.511 0.651 0.564 -
7/16 0.587 0.747 0.647 10.22
15/32 0.668 0.850 0.736 -
1/2 0.754 0.960 0.831 13.36
17/32 0.845 1.080 0.932 -
9/16 0.941 1.200 1.040 16.90
19/32 1.043 1.330 1.150 -
5/8 1.150 1.460 1.270 20.86
21/32 1.260 1.610 1.400 -
11/16 1.380 1.760 1.520 25.20
23/32 1.500 1.910 1.660 -
3/4 1.630 2.080 1.800 30.00
25/32 1.760 2.250 1.940 -
13/16 1.900 2.420 2.100 35.20
27/32 2.050 2.610 2.250 -
7/8 2.200 2.800 2.420 40.90
29/32 2.350 2.990 2.590 -
15/16 2.510 3.190 2.760 47.00
31/32 26.70 3.400 2.950 -
1 3.020 3.840 3.320 53.40
1 1/16 3.380 4.300 3.730 60.40
1 1/8 3.770 4.800 4.150 67.60
1 3/16 4.170 5.320 4.600 75.40
1 1/4 4.600 5.860 5.070 83.40
1 5/16 5.050 6.430 5.570 92.00
1 3/8 5.520 7.030 6.090 101.00
1 7/16 6.010 7.660 6.630 110.40
1 1/2 6.520 8.300 7.190 120.20
1 9/16 7.050 8.980 7.780 -
1 5/8 141.00

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
2 Inc. cannot be held liable for any inaccuracies.

WEIGHTS OF ROUND, SQUARE, AND HEXAGON BARS Shapes & Sizes
POUNDS PER FOOT

Size Rounds Squares Hexagons Wt/20’ Bar
Inches 7.600 9.680 8.390 Rounds Only
1 11/16 8.180 10.410 9.020 -
1 3/4 8.770 11.170 9.670 163.60
1 13/16 9.390 11.950 10.350 -
1 7/8 10.020 12.760 11.050 187.80
1 15/16 10.680 13.600 11.780 -
2 11.360 14.460 12.530 213.60
2 1/16 12.060 15.350 13.300 -
2 1/8 12.780 16.270 14.090 241.20
2 3/16 13.520 17.210 14.910 -
2 1/4 14.280 18.180 15.750 270.40
2 5/16 15.060 19.180 16.610 -
2 3/8 15.870 20.200 17.490 301.20
2 7/16 16.690 21.250 18.400 -
2 1/2 18.400 23.430 20.290 333.80
2 5/8 20.190 25.710 22.270 368.00
2 3/4 22.070 28.100 24.340 403.90
2 7/8 24.030 30.600 26.500 441.40
3 26.080 33.200 28.760 480.60
3 1/8 28.210 35.910 31.100 521.60
3 1/4 30.420 38.730 33.540 564.20
3 3/8 32.710 41.650 36.070 608.40
3 1/2 35.090 44.680 38.690 654.20
3 5/8 37.550 47.810 41.410 701.80
3 3/4 40.100 51.050 44.210 751.00
3 7/8 42.730 54.400 47.110 802.00
4 45.440 57.850 50.100 854.60
4 1/8 48.230 61.410 53.180 908.80
4 1/4 51.110 65.080 56.360 964.60
4 3/8 54.080 68.850 59.630 1022.20
4 1/2 57.120 72.730 62.980 1081.60
4 5/8 60.250 76.710 66.440 1143.40
4 3/4 63.460 80.800 69.980 1205.00
4 7/8 66.760 85.000 73.610 1269.20
5 70.140 89.300 77.340 1335.20
5 1/8 73.600 93.710 81.160 1402.80
5 1/4 77.150 98.230 85.070 1472.00
5 3/8 80.780 102.850 89.070 1546.00
5 1/2 84.490 107.580 93.160 1615.60
5 5/8 88.290 112.410 97.350 1689.80
5 3/4 92.170 117.350 101.630 1765.80
5 7/8 96.130 122.400 106.000 1843.40
6 1922.60

3

HOT ROLLED STRIP B
A

Size In Inches 1/2 Wt/Ft Wt/20’ Size In Inches 5 1/2 Wt/Ft Wt/20’
1/8 x 5/8 0.213 4.26 1/8 x 6 2.340 46.80
3/4 0.266 5.32 3/16 x 7 2.550 51.00
7/8 0.319 6.38 8 2.980 59.50
1 0.372 7.44 9 3.400 68.00
1 1/8 0.425 8.50 10 3.830 76.60
1 1/4 0.478 9.56 12 4.250 85.00
1 1/2 0.531 10.62 1/2 5.100 102.00
1 3/4 0.638 12.76 5/8 0.319 6.38
2 0.744 14.88 3/4 0.398 7.96
2 1/4 0.850 17.00 1 0.478 9.56
2 1/2 0.956 19.12 1 1/8 0.638 12.76
2 3/4 1.060 21.20 1 1/4 0.717 14.34
3 1.170 23.40 1 1/2 0.797 15.94
3 1/2 1.280 25.60 1 3/4 0.956 19.12
4 1.490 29.80 2 1.120 22.40
4 1/2 1.700 34.00 2 1/4 1.280 25.60
5 1.910 38.20 2 1/2 1.430 28.60
2.130 42.60 1.590 31.80

800.423.8016 | www.JimsSupply.com

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
4 Inc. cannot be held liable for any inaccuracies.

HOT ROLLED STRIP B Shapes & Sizes

Size in Inches 2 3/4 Wt/Ft A
3/16 x 3 1.750
3 1/2 1.910 Wt/20’
4 2.230 35.00
4 1/2 2.550 38.20
5 2.870 44.60
5 1/2 3.190 51.00
6 3.510 57.40
7 3.830 63.80
8 4.460 70.20
9 5.100 76.60
10 5.740 89.20
11 6.380 102.00
12 7.020 114.80
7.650 127.60
140.40
153.00

FLATS B
A

Size in Inches 1/2 Wt/Ft Wt/20’
1/4 x 3/4 0.43 8.50
1 0.64 12.76
1 1/4 0.85 17.00
1 1/2 1.06 21.20
1 3/4 1.28 25.60
1 7/8 1.49 29.80
2 1.59 31.80
2 1/4 1.70 34.00
2 1/2 1.91 38.20
2 5/8 2.13 42.60
2 3/4 2.23 44.60
3 2.34 46.80
3 1/2 2.55 51.00
2.98 59.60

5

FLATS B
A

Size in Inches 4 Wt/Ft Wt/20’
1/4 x 4 1/2 3.40 68.00
5/16 x 5 3.83 76.60
5/16 x 5 1/2 4.25 85.00
6 4.68 93.60
7 5.10 102.00
8 5.95 119.00
3/4 6.80 136.00
1 0.80 15.94
1 1/4 1.06 21.20
1 1/2 1.33 26.60
1 3/4 1.59 31.80
2 1.86 37.20
2 1/4 2.13 42.60
2 1/2 1.39 47.80
3 2.66 53.20
3 1/2 3.19 63.80
4 3.72 74.40
4 1/2 4.25 85.00
4.78 95.60

800.423.8016 | www.JimsSupply.com

Loading Jim’s Supply trucks for deliveries
6

B Shapes & Sizes
A

Disclaimer: The weights listed in this catalog may vary depending on producing 7
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
Inc. cannot be held liable for any inaccuracies.

FLATS

Size in Inches 3/4 Wt/Ft Wt/20’
1/2 x 1 1.28 25.60
5/8 x 1 1/4 1.70 34.00
1 1/2 2.13 42.60
1 3/4 2.55 51.00
2 2.98 59.60
2 1/4 3.40 68.00
2 1/2 3.83 76.60
2 3/4 4.25 85.00
3 4.68 93.60
3 1/2 5.10 102.00
4 5.95 119.00
4 1/2 6.80 136.00
5 7.65 153.00
5 1/2 8.50 170.00
6 9.35 187.00
7 10.20 204.00
8 11.90 238.00
3/4 13.60 272.00
1 1.595 31.90
1 1/4 2.13 42.60
1 1/2 2.66 53.20
1 3/4 3.19 63.80
2 3.72 74.40
2 1/4 4.25 85.00
2 1/2 4.78 95.60
3 5.31 106.20
3 1/2 6.38 127.60
4 7.44 148.80
4 1/2 8.50 170.00
9.56 191.20

800.423.8016 | www.JimsSupply.com

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
8 Inc. cannot be held liable for any inaccuracies.

Shapes & Sizes 9

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
10 Inc. cannot be held liable for any inaccuracies.

FLATS

Size in Inches 4 Wt/Ft Wt/20’ Shapes & Sizes
1 1/4 x 4 1/2 17.00 340.00
1 1/2 x 5 19.13 382.60
5 1/2 21.25 425.00
1 3/4 x 6 23.38 467.60
2x 7 25.50 510.00
2 1/2 x 8 29.75 595.00
2 34.00 680.00
2 1/2 10.20 204.00
3 12.75 255.00
3 1/2 15.30 306.00
4 17.85 357.00
4 1/2 20.40 408.00
5 22.95 459.00
5 1/2 25.50 510.00
6 28.05 561.00
7 30.60 612.00
8 35.70 714.00
2 40.80 816.00
2 1/2 11.90 238.00
3 14.88 297.60
3 1/2 17.85 357.00
4 20.83 416.60
4 1/2 23.80 476.00
5 26.78 535.60
6 29.75 595.00
8 35.70 714.00
2 1/2 47.60 952.00
3 17.00 340.00
3 1/2 20.40 408.00
4 23.80 476.00
4 1/2 27.20 544.00
5 30.60 612.00
6 34.00 680.00
7 40.80 816.00
8 47.60 952.00
3 54.40 1088.00
3 1/2 25.50 510.00
29.75 595.00

Other Sizes Available

11

FLATS

Size in Inches 4 Wt/Ft Wt/20’
2 1/2 x 4 1/2 34.00 680.00
3x 5 38.25 765.00
6 42.50 850.00
4 51.00 1020.00
4 1/2 40.80 816.00
5 45.90 918.00
6 51.00 1020.00
61.20 1224.00

Other Sizes Available

UNIVERSAL MILL PLATES

Size in Inches Wt/Ft Wt/20’
1/4 9 7.65 153.00
10 8.50 170.00
11 9.36 187.20
12 10.20 204.00
5/16 9 9.57 191.40
10 10.64 212.80
11 11.70 234.00
12 12.76 255.20
3/8 9 11.49 229.80
10 12.77 255.40
11 14.04 280.80
12 15.32 306.40
1/2 9 15.32 306.40
10 17.02 340.40
11 18.72 374.40
12 20.42 408.40
5/8 9 19.14 382.80
10 21.27 425.40
11 23.40 468.00
12 25.53 510.60
3/4 9 22.95 459.00
10 25.50 510.00
11 28.05 561.00
12 30.60 612.00
7/8 9 26.80 536.00
10 29.80 596.00
11 32.80 656.00
12 35.74 714.80
1 9 30.60 612.00
10 34.00 680.00
11 37.40 748.00
12 40.80 816.00
1 1/4 8 34.00 680.00
12

UNIVERSAL MILL PLATES

Size in Inches 9 Wt/Ft Wt/20’ Shapes & Sizes
1/4 10 38.30 766.00
1 1/2 11 42.50 850.00
12 46.80 936.00
1 3/4 8 51.00 1020.00
2 9 40.80 816.00
10 45.90 918.00
11 51.00 1020.00
12 56.10 1122.00
9 61.20 1224.00
10 53.60 1072.00
11 59.56 1191.20
12 65.51 1310.20
8 71.47 1429.40
9 54.40 1088.00
10 61.26 1225.20
11 68.00 1360.00
12 74.90 1498.00
81.60 1632.00

SHEETS
We stock sizes not listed. Sheet sizes listed are for reference only.

Size Decimal Decimal Limits/ Wt/Sq Ft Black Wt/
Average GA 7.5 Sheet
(.1868-.1719) 5.625 240.0
3/16 0.1793 48 x 96 300.0
10 GA. 0.1345 48 x 120 600.0
48 x 240 300.0
60 x 96 375.0
60 x 120 750.0
60 x 240 360.0
72 x 96 450.0
72 x 120 900.0
72 x 240 180.0
(.1419 - .1271) 225.0
48 x 96 270.0
48 x 120 450.0
48 x 144 225.0
48 x 240 281.3
60 x 96 337.5
60 x 120 562.5
60 x 144 270.0
60 x 240 337.5
72 x 96 405.0
72 x 120 675.0
72 x 144
72 x 240

13

SHEETS
We stock sizes not listed. Sheet sizes listed are for reference only.

Size Decimal Decimal Limits/ Wt/Sq Ft Black Wt/
Average GA 5.0 Sheet
(.1270-.1121) 4.375 160.0
11 GA. 0.1196 48 x 96 200.0
12 GA. 0.1046 48 x 120 240.0
48 x 144 400.0
48 x 240 200.0
60 x 96 250.0
60 x 120 300.0
60 x 144 500.0
60 x 240 240.0
72 x 96 300.0
72 x 120 360.0
72 x 144 600.0
72 x 240
(.1120 - .0972) 140.0
48 x 96 175.0
48 x 120 210.0
48 x 144 350.0
48 x 240 175.0
60 x 96 218.8
60 x 120

800.423.8016 | www.JimsSupply.com

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
14 Inc. cannot be held liable for any inaccuracies.

SHEETS Shapes & Sizes
We stock sizes not listed. Sheet sizes listed are for reference only.

Size Decimal Decimal Limits/ Wt/Sq Ft Black Wt/
Average GA 4.375 Sheet
(.1120 - .0972)
12 GA. 0.1046 60 x 144 3.125 262.5
60 x 240 437.6
14 GA. 0.0747 72 x 96 2.500 210.0
72 x 120 262.5
16 GA. 0.0598 72 x 144 315.0
72 x 240 525.0
(.0821 - .0710) 100.0
48 x 96 125.0
48 x 120 150.0
48 x 144 125.0
60 x 96 156.3
60 x 120 187.5
60 x 144 60.0
(.0635 - 0.568) 75.0
36 x 96 90.0
36 x 120 80.0
36 x 144 100.0
48 x 96 120.0
48 x 120 100.0
48 x 144 125.0
60 x 96 150.0
60 x 120
60 x 144

COLD ROLLED SHEETS

Decimal Wt/Sq Ft
Average

18 GA. 0.0478 (.0508 - .0449) 2.000
20 GA. 0.0359 (.0388 - .0344) 1.500
22 GA. 0.0299 (.0313 - .0284) 1.250
24 GA. 0.0239 (.0254 - .0225) 1.000
26 GA. 0.0179 (.0194 - .0172) 0.750
28 GA. 0.0149 (.0156 - .0142) 0.625

15

PLATES - A - 36

STOCK WIDTHS FOR THE FOLLOWING ARE AVAILABLE IN 4’, 5’, 6’, 7’, 8’
STOCK LENGTHS FOR THE FOLLOWING ARE AVAILABLE IN 8’, 10’, 12’, 20’ OR SPECIAL LENGTHS

Size in Inches Dec. Equiv. Wt/Sq Ft
3/16 0.1875 7.66
1/4 0.2500 10.21
5/16 0.3125 12.76
3/8 0.3750 15.31
7/16 0.4375 17.87
1/2 0.5000 20.42
9/16 0.5625 22.97
5/8 0.6250 25.52
11/16 0.6875 28.08
3/4 0.7500 30.63
13/16 0.8125 33.18
7/8 0.8750 35.74
15/16 0.9375 38.29
1 1.0000 40.84
1 1/16 1.0625 45.20
1 1/8 1.1250 45.94
1 3/16 1.1875 48.50
1 1/4 1.2500 51.05
1 5/16 1.3125 53.60
1 3/8 1.3750 56.15
1 7/16 1.4375 58.71
1 1/2 1.5000 61.26
1 9/16 1.5625 63.81
1 5/8 1.6250 66.36
1 11/16 1.6875 68.92
1 3/4 1.7500 71.47
1 13/16 1.8125 74.92
1 7/8 1.8750 76.57
1 15/16 1.9375 79.12
2 2.000 81.68
2 1/16 2.0625 84.22
2 1/8 2.1250 86.78
2 3/16 2.1875 89.25
2 1/4 2.2500 91.89
2 5/16 2.3125 94.44
2 3/8 2.3750 96.99
2 7/16 2.4375 99.54
2 1/2 2.5000 102.10
2 9/16 2.5625 104.65
2 5/8 2.6250 107.20
2 11/16 2.6875 109.75
2 3/4 2.7500 112.31
2 3/16 2.1875 89.25
16

STOCK WIDTHS FOR THE FOLLOWING ARE AVAILABLE IN 4’, 5’, 6’, 7’, 8’ Shapes & Sizes
STOCK LENGTHS FOR THE FOLLOWING ARE AVAILABLE IN 8’, 10’, 12’, 20’ OR SPECIAL LENGTHS

17

GALVANIZED SHEETS

Galvanized Equivalent Gauge Thickness Weight
Sheet Thickness Ordering Limits - Pounds
Gauge No. Inch Inch Per Sq. Ft.
26 0.0217 .0231 - .0210 0.906
28 0.0187 .0194 - .0180 0.781

FLOOR PLATE

By Gauge Size Width Inches Wt/Sq Ft
14 GA. x 48 3.75
12 GA. x 60 3.75
48 5.25
60 5.25
Wt/Sq Ft
By Inches Size Width Inches 6.16
1/8 x 48 6.16
3/16 x 60 6.16
1/4 x 72 8.71
5/16 x 48 8.71
3/8 x 60 8.71
1/2 x 72 11.26
48 11.26
60 11.26
72 11.26
96 13.81
48 13.81
60 13.81
72 13.81
96 16.37
48 16.37
60 16.37
72 16.37
96 21.47
48 21.47
60 21.47
72 21.47
96

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
18 Inc. cannot be held liable for any inaccuracies.

BAR SIZE ANGLES - EQUAL Shapes & Sizes

Size in Inches 1/2 x Wt/Ft Wt/20’ Wt/40’
1/2 x 3/4 x 1/8 0.38 7.60 15.20
3/4 x 1 x 1/8 0.59 11.80 23.60
1x 1/8 0.80 16.00 32.00
3/16 1.16 23.20 46.40
1 1/4 x 1 1/4 x 1/4 1.49 29.80 59.60
1/8 1.01 20.20 40.40
1 1/2 x 1 1/2 x 3/16 1.48 29.60 59.20
1/4 1.92 38.40 76.80
1 3/4 x 1 3/4 x 1/8 1.23 24.60 49.20
3/16 1.80 36.00 72.00
2x2x 1/4 2.34 46.80 93.60
1/8 1.44 28.80 57.60
2 1/2 x 2 1/2 x 3/16 2.12 42.40 84.80
1/4 2.77 55.40 110.80
1/8 1.65 33.00 66.00
3/16 2.44 48.80 97.60
1/4 3.19 63.80 127.60
5/16 3.92 78.40 156.80
3/8 4.70 94.00 188.00
3/16 3.07 61.40 122.80
1/4 4.10 82.00 164.00
5/16 5.00 100.00 200.00
3/8 5.90 118.00 236.00
1/2 7.70 154.00 308.00

BAR SIZE ANGLES - UNEQUAL

Size in Inches 1 1/4 x Wt/Ft Wt/20’ Wt/40’
2x 1 1/2 x 3/16 1.96 39.20 78.40
2x 1/4 2.55 51.00 102.00
1 1/2 x 1/8 1.44 28.80 57.60
2 1/2 x 2x 3/16 2.12 42.40 84.80
2 1/2 x 1/4 2.77 55.40 110.80
3/16 2.44 48.80 97.60
1/4 3.19 63.80 127.60
3/16 2.75 55.00 110.00
1/4 3.62 72.40 144.80
5/16 4.50 90.00 180.00
3/8 5.30 106.00 212.00

19

STRUCTURAL ANGLES - EQUAL

Size in Inches 3x Wt/Ft Wt/20’ Wt/40’
3x 3 1/2 x 3/16 3.71 74.20 148.40
3 1/2 x 4x 1/4 4.90 98.00 196.00
4x 5x 5/16 6.10 122.00 244.00
5x 6x 3/8 7.20 144.00 288.00
6x 8x 1/2 9.40 188.00 376.00
8x 1/4 5.80 116.00 232.00
5/16 7.20 144.00 288.00
3/8 8.50 170.00 340.00
1/2 11.10 222.00 444.00
1/4 6.60 132.00 264.00
5/16 8.20 164.00 328.00
3/8 9.80 196.00 392.00
1/2 12.80 256.00 512.00
5/8 15.70 314.00 628.00
5/16 10.30 206.00 412.00
3/18 12.30 246.00 492.00
1/2 16.20 324.00 648.00
5/16 12.40 248.00 496.00
3/8 14.90 298.00 596.00
1/2 19.60 392.00 784.00
5/8 24.20 484.00 968.00
3/4 28.70 574.00 1148.00
1/2 26.40 528.00 1056.00
9/16 29.60 592.00 1184.00
5/8 32.70 654.00 1308.00
3/4 38.60 778.00 1556.00
1 51.00 1020.00 2040.00

STRUCTURAL ANGLES - UNEQUAL ANGLE

3x2x 3/16 3.06 2.00 124.00
1/4 4.10 82.00 164.00
5/16 5.00 100.00 200.00
3/8 5.90 118.00 236.00
1/2 7.70 154.00 308.00
3 x 2 1/2 x 3/16 3.39 67.80 135.60
1/4 4.50 90.00 180.00
5/16 5.60 112.00 224.00
3/8 6.60 132.00 264.00
1/2 8.50 170.00 340.00
3 1/2 x 2 1/2 x 1/4 4.90 98.00 196.00
5/16 6.10 122.00 244.00
3/8 7.20 144.00 288.00
1/2 9.40 188.00 376.00
20

STRUCTURAL ANGLES - UNEQUAL ANGLE Shapes & Sizes

Size in Inches x 1/4 Wt./Ft. Wt./20’ Wt./40’
3 1/2 x 3 5/16 5.40 108.00 216.00
3/8 6.60 132.00 264.00
4x3x 1/2 7.90 158.00 316.00
1/4 10.20 204.00 408.00
4 x 3 1/2 x 5/16 5.80 116.00 232.00
5x3x 3/8 7.20 144.00 288.00
5 x 3 1/2 x 1/2 8.50 170.00 340.00
6 x 3 1/2 x 5/8 11.10 222.00 444.00
6x4x 1/4 13.60 272.00 544.00
5/16 6.20 124.00 248.00
7x4x 3/8 7.70 154.00 308.00
1/2 9.10 182.00 364.00
8x4x 1/4 11.90 238.00 476.00
8x6x 5/16 6.60 132.00 264.00
3/8 8.20 164.00 328.00
1/2 9.80 196.00 392.00
1/4 12.80 256.00 512.00
5/16 7.00 140.00 280.00
3/8 8.70 174.00 348.00
1/2 10.40 208.00 416.00
1/4 13.60 272.00 544.00
5/16 7.90 158.00 316.00
3/8 9.80 196.00 392.00
1/2 11.70 234.00 468.00
5/16 15.30 306.00 612.00
3/8 10.30 206.00 412.00
1/2 12.30 246.00 492.00
5/8 16.20 324.00 648.00
3/4 20.00 400.00 800.00
3/8 23.60 472.00 944.00
7/16 13.60 272.00 544.00
1/2 15.80 316.00 632.00
5/8 17.90 358.00 716.00
3/4 22.10 442.00 884.00
7/16 26.20 524.00 1048.00
1/2 17.20 344.00 688.00
5/8 19.60 392.00 784.00
3/4 24.20 448.00 968.00
7/16 28.70 574.00 1148.00
1/2 20.20 404.00 808.00
5/8 23.00 460.00 920.00
3/4 28.50 570.00 1140.00
1 33.80 676.00 1352.00
44.20 884.00 1768.00

21

Size in Inches 1/2 BAR SIZE CHANNELS Wt./20’
1x 1/2 Wt./Ft. 16.40
1 1/4 x 1/2 20.20
1 1/2 x 1/2 x 1/8 0.82 22.40
2x 1 x 1/8 1.01 28.60
2x x 1/8 1.12 35.60
x 1/8 1.43 51.40
x 1/8 1.59

3/16 2.32

STRUCTURAL CHANNELS

Depth in Inches Depth in Flange Width Web Thickness
& Lbs. per Foot Inches In Inches Inches
C3 x 4.1 3 1.410 0.170
C3 x 5 3 1.498 0.258
C3 x 6 3 1.596 0.356
C4 x 5.4 4 1.584 0.184
C4 x 6.25 4 1.647 0.247
C4 x 7.25 4 1.721 0.321
C5 x 6.7 5 1.750 0.190
C5 x 9 5 1.885 0.325
C6 x 8.2 6 1.920 0.200
C6 x 10.5 6 2.034 0.314
C6 x 13 6 2.157 0.437
C7 x 9.8 7 2.090 0.210
C7 x 12.25 7 2.194 0.314
C7 x 14.75 7 2.299 0.419
C8 x 11.5 8 2.260 0.220
C8 x 13.75 8 2.343 0.303
C8 x 18.75 8 2.527 0.487
C9 x 13.4 9 2.433 0.233
C9 x 15 9 2.485 0.285
C10 x 15.3 10 2.600 0.240
C10 x 20 10 2.739 0.379
C10 x 25 10 2.886 0.526
C10 x 30 10 3.033 0.673
C12 x 20.7 12 2.942 0.282
C12 x 25 12 3.047 0.387
C12 x 30 12 3.170 0.510
C15 x 33.9 15 3.400 0.400
C15 x 40 15 3.520 0.520
22 C15 x 50 15 3.716 0.716

SIZE IN INCHES & JR. CHANNELS WT/40’ Shapes & Sizes
WIDTH OF FLANGE WT/FT 340.00
8 x 1.875 8.5 260.00
10 x 1.127 6.5 336.00
10 x 1.500 8.4 424.00
12 x 1.500 10.6

SHIP & CAR CHANNELS

SIZE IN INCHES & WT/FT WT/40’
WIDTH OF FLANGE 7.10 284
3 x 1.938 9.00 360
2.122 13.80 552
4 x 2.500 12.00 480
6 x 2.497 15.10 604
2.941 15.30 612
3.500 16.30 652
3.000 18.00 720
3.504 17.60 704
7 x 3.000 19.10 764
3.452 22.70 908
3.603 18.70 748
8 x 2.978 20.00 800
3.025 21.40 856
3.450 22.80 912
3.502 22.00 880
10 x 3.450 25.00 1000
3.402 31.00 1240
12 x 3.670 35.00 1400
3.767 37.00 1480
3.600 40.00 1600
3.890 50.00 2000
4.135 31.80 1272
13 x 4.000 50.00 2000
4.412 42.70 1708
18 x 3.950 45.80 1832
4.000 51.90 2076
4.100 58.00 2320
4.200

SIZE IN INCHES WT/FT WIDE FLANGE BEAMS WT/40’ WT/60’

4x4 13.0 DEPTH OF FLANGE FLANGE WEB 520 780
5x5 16.0 SECTION WIDTH THICKNESS THICKNESS 640 960
19.0 760 1140 23
4.16 4.060 0.345 0.280
5.01 5.000 0.360 0.240
5.15 5.030 0.430 0.270

WIDE FLANGE BEAMS

SIZE IN INCHES WT/FT DEPTH OF FLANGE FLANGE WEB WT/40’ WT/60’
SECTION WIDTH THICKNESS THICKNESS
6x4 9.0 360 540
6x6 12.0 5.90 3.940 0.215 0.170 480 720
8x4 16.0 6.03 4.000 0.280 0.230 640 960
8 x 5 1/4 15.0 6.28 4.030 0.405 0.260 600 900
8 x 6 1/2 20.0 5.99 5.990 0.260 0.230 800 1200
8x8 25.0 6.20 6.020 0.365 0.260 1000 1500
10.0 6.38 6.080 0.455 0.320 400 600
10 x 4 13.0 7.89 3.940 0.205 0.170 520 780
15.0 7.99 4.000 0.255 0.230 600 900
10 x 5 3/4 18.0 8.11 4.015 0.315 0.245 720 1080
10 x 8 21.0 8.14 5.250 0.330 0.230 840 1260
10 x 10 24.0 8.28 5.270 0.400 0.250 960 1440
28.0 7.93 6.495 0.400 0.245 1120 1680
12 x 4 31.0 8.06 6.535 0.465 0.285 1240 1860
35.0 8.00 7.995 0.435 0.285 1400 2100
12 x 6 1/2 40.0 8.12 8.020 0.495 0.310 1600 2400
12 x 8 48.0 8.25 8.070 0.560 0.360 1920 2880
24 58.0 8.50 8.110 0.685 0.400 2320 3480
67.0 8.75 8.220 0.810 0.510 2680 4020
12.0 9.00 8.280 0.935 0.570 480 720
15.0 9.87 3.960 0.210 0.190 600 900
17.0 9.99 4.000 0.270 0.230 680 1020
19.0 10.11 4.010 0.330 0.240 760 1140
22.0 10.24 4.020 0.395 0.250 880 1320
26.0 10.17 5.750 0.360 0.240 1040 1560
30.0 10.33 5.770 0.440 0.260 1200 1800
33.0 10.47 5.810 0.510 0.300 1320 1980
39.0 9.73 7.960 0.435 0.290 1560 2340
45.0 9.92 7.985 0.530 0.315 1800 2700
49.0 10.10 8.020 0.620 0.350 1960 2940
54.0 9.798 10.000 0.560 0.340 2160 3240
60.0 10.09 10.030 0.615 0.370 2400 3600
68.0 10.22 10.080 0.680 0.420 2720 4080
77.0 10.40 10.130 0.770 0.470 3080 4620
88.0 10.60 10.190 0.870 0.530 3520 5280
100.0 10.84 10.265 0.990 0.605 4000 6000
112.0 11.10 10.340 1.120 0.680 4480 6720
14.0 11.36 10.415 1.250 0.755 560 840
16.0 11.91 3.970 0.225 0.200 640 960
19.0 11.99 3.990 0.265 0.220 760 1140
22.0 12.16 4.005 0.350 0.235 880 1320
26.0 12.31 4.030 0.425 0.260 1040 1560
30.0 12.22 6.490 0.380 0.230 1200 1800
35.0 12.34 6.520 0.440 0.260 1400 2100
40.0 12.50 6.560 0.520 0.300 1600 2400
45.0 11.94 8.005 0.515 0.295 1800 2700
12.06 8.045 0.575 0.335

WIDE FLANGE BEAMS

SIZE IN INCHES DEPTH OF FLANGE FLANGE WEB WT/60’ Shapes & Sizes
WT/FT SECTION WIDTH THICKNESS THICKNESS WT/40’
12 x 3000
12 x 50.0 12.19 8.080 0.640 0.370 2000 3180
10 53.0 12.06 9.995 0.575 0.345 2120 3480
14 x 58.0 12.19 10.010 0.640 0.360 2320 3900
14 x 12 65.0 12.12 12.000 0.605 0.390 2600 4320
14 x 72.0 12.25 12.040 0.670 0.430 2880 4740
14 x 79.0 12.38 12.080 0.735 0.470 3160 5220
14 x 87.0 12.53 12.125 0.810 0.515 3480 5760
96.0 12.71 12.160 0.900 0.550 3840 6360
16 x 106.0 12.89 12.220 0.990 0.610 4240 7200
16 x 120.0 13.12 12.320 1.105 0.710 4800 8160
136.0 13.41 12.400 1.250 0.790 5440 9120
16 x 152.0 13.71 12.480 1.400 0.870 6080 10200
170.0 14.03 12.570 1.560 0.960 6800 11400
190.0 14.38 12.670 1.735 1.060 7600 1100
5 22.0 13.74 5.000 0.335 0.230 880 1300
26.0 13.91 5.025 0.420 0.225 1040 1800
6 3/4 30.0 13.84 6.730 0.385 0.270 1200 2040
34.0 13.98 6.745 0.455 0.285 1360 2280
38.0 14.10 6.770 0.515 0.310 1520 2580
8 43.0 13.66 7.995 0.530 0.305 1720 2880
48.0 13.79 8.030 0.595 0.340 1920 3180
53.0 13.92 8.060 0.660 0.370 2120 3660
10 61.0 13.89 9.995 0.645 0.375 2440 4080
68.0 14.04 10.035 0.720 0.415 2720 4440
74.0 14.17 10.070 0.785 0.450 2960 4920
82.0 14.31 10.130 0.855 0.510 3280 4380
14 1/2 73.0 13.61 14.585 0.505 0.505 2920 5340
89.0 13.83 14.695 0.615 0.615 3560 5400
90.0 14.02 14.520 0.710 0.440 3600 5940
99.0 14.06 14.565 0.780 0.485 3960 6120
102.0 14.01 14.785 0.705 0.705 4080 6540
109.0 14.32 14.605 0.860 0.525 4360 7020
117.0 14.21 14.885 0.805 0.805 4680 7200
120.0 14.48 14.670 0.940 0.590 4800 7920
132.0 14.66 14.725 1.030 0.645 5280 1300
5 1/2 26.0 15.69 5.500 0.345 0.250 1040 1550
31.0 15.88 5.525 0.440 0.275 1240 2160
7 36.0 15.86 6.985 0.430 0.295 1440 2400
40.0 15.01 6.995 0.505 0.305 1600 2700
45.0 16.13 7.035 0.565 0.345 1800 3000
50.0 16.26 7.070 0.630 0.380 2000 3420
57.0 16.43 7.120 0.715 0.430 2280 4020
10 1/4 67.0 16.33 10.235 0.665 0.395 2680 4620
77.0 16.52 10.295 0.760 0.455 3080 5340
89.0 16.75 10.365 0.875 0.525 3560 6000 25
100.0 16.97 10.425 0.985 0.585 4000

WIDE FLANGE BEAMS

SIZE IN INCHES DEPTH OF FLANGE FLANGE WEB WT/60’
WT/FT SECTION WIDTH THICKNESS THICKNESS WT/40’
18 x 2100
6 35.0 17.70 6.000 0.425 0.300 1400 2400
18 x 40.0 17.90 6.015 0.525 0.315 1600 2760
46.0 18.06 6.060 0.605 0.360 1840 3000
7 1/2 50.0 17.99 7.495 0.570 0.355 2000 3300
55.0 18.11 7.530 0.630 0.390 2200 3600
60.0 18.24 7.555 0.695 0.415 2400 3900
65.0 18.35 7.590 0.750 0.450 2600 4260
71.0 18.47 7.635 0.810 0.495 2840 4560
18 x 11 76.0 18.21 11.035 0.680 0.425 3040 5160
86.0 18.39 11.090 0.770 0.480 3440 5820
97.0 18.59 11.145 0.870 0.535 3880 6360
106.0 18.73 11.200 0.940 0.590 4240 7140
119.0 18.87 11.265 1.060 0.655 4760 2640
21 x 6 1/2 44.0 20.66 6.500 0.450 0.350 1760 3000
21 x 50.0 20.83 6.530 0.535 0.380 2000 3420
57.0 21.06 6.555 0.650 0.405 2280 3720
8 1/4 62.0 20.99 8.420 0.615 0.400 2480 4080
68.0 21.13 8.270 0.685 0.430 2720 4380
73.0 21.24 8.295 0.740 0.455 2920 4980
83.0 21.43 8.355 0.835 0.515 3320 5580
93.0 21.62 8.420 0.930 0.580 3720 6060
21 x 12 1/4 101.0 21.36 12.290 0.800 0.500 4040 6660
111.0 21.51 12.340 0.875 0.550 4440 7320
122.0 21.68 12.390 0.960 0.600 4880 7920
132.0 21.83 12.440 1.035 0.650 5280 8820
147.0 22.06 12.510 1.150 0.720 5880 3300
24 x 7 55.0 23.57 7.005 0.505 0.395 2200 3720
24 x 62.0 23.74 7.040 0.590 0.430 2480 4080
9 68.0 23.73 8.965 0.585 0.415 2720 4560
24 x 76.0 23.92 8.990 0.680 0.440 3040 5040
84.0 24.10 8.020 0.770 0.470 3360 5640
94.0 24.31 9.065 0.875 0.515 3760 6240
12 3/4 104.0 24.06 12.750 0.750 0.500 4160 7020
117.0 24.26 12.800 0.850 0.550 4680 7860
131.0 24.48 12.855 0.960 0.605 5240 8760
146.0 24.74 12.900 1.090 0.650 5840 9720
162.0 25.00 12.955 1.220 0.705 6480 5040
27 x 10 84.0 26.71 9.960 0.640 0.460 3360 5640
94.0 26.92 9.990 0.745 0.490 3760 6120
102.0 27.09 10.015 0.830 0.505 4080 6840
114.0 27.29 10.070 0.930 0.570 4560 8760
27 x 14 146.0 27.38 13.965 0.975 0.605 5840 9660
161.0 27.59 14.020 1.080 0.660 6440 10680
178.0 27.81 14.085 1.190 0.725 7120 5940
30 x 10 1/2 99.0 29.65 10.450 0.670 0.520 3960 6480
26 108.0 29.83 10.475 0.760 0.545 4320

WIDE FLANGE BEAMS

SIZE IN INCHES DEPTH OF FLANGE FLANGE WEB Shapes & Sizes
WT/FT SECTION WIDTH THICKNESS THICKNESS WT/40’ WT/60’
30 x
33 x 116.0 30.01 10.495 0.850 0.565 4640 6960
33 x 124.0 30.17 10.515 0.930 0.585 4960 7440
36 x 132.0 30.31 10.545 1.000 0.615 5280 7920
15 173.0 30.44 14.985 1.065 0.655 6920 10380
36 x 191.0 30.68 15.040 1.185 0.710 7640 11460
11 1/2 152.0 33.49 11.565 1.055 0.635 6080 9120
15 1/4 201.0 33.68 15.745 1.150 0.715 8040 12060
221.0 33.93 15.805 1.275 0.775 8840 13260
241.0 34.18 15.860 1.400 0.830 9640 14460
12 135.0 35.55 11.950 0.790 0.600 5400 8100
150.0 35.85 11.975 0.940 0.625 6000 9000
160.0 36.01 12.000 1.020 0.650 6400 9600
170.0 36.17 12.030 1.100 0.680 6800 10200
182.0 36.33 12.075 1.180 0.725 7280 10920
194.0 36.49 12.115 1.260 0.765 7760 11640
210.0 36.69 12.180 1.360 0.830 8400 12600
16 1/2 230.0 35.90 16.470 1.260 0.760 9200 13800
245.0 36.08 16.510 1.350 0.800 9800 14700
260.0 36.26 16.550 1.440 0.840 10400 15600
280.0 36.52 16.595 1.570 0.885 11200 16800
300.0 36.74 16.655 1.680 0.945 12000 18000

I BEAMS

SIZE IN INCHES & WT/FT THICKNESS WT/40’
WIDTH OF FLANGE OF WEB INS. 228
300
3x 2.330 5.70 0.170 308 27
4x 2.509 7.50 0.349 380
5x 2.663 7.70 0.193 400
6x 2.796 9.50 0.326 500
7x 3.004 10.00 0.214 690
8x 3.332 12.50 0.232 612
10 x 3.565 17.25 0.465 736
12 x 3.362 15.30 0.252 920
4.001 18.40 0.271 1016
15 x 4.101 23.00 0.441 1400
18 x 4.661 25.40 0.311 1272
4.944 35.00 0.594 1400
5.000 31.80 0.350 1632
5.078 35.00 0.428 2000
5.252 40.80 0.462 1716
5.477 50.00 0.687 2000
5.501 42.90 0.411 2188
5.640 50.00 0.550
6.001 54.70 0.461

I BEAMS

SIZE IN INCHES & WT/FT THICKNESS WT/40’
WIDTH OF FLANGE 70.00 OF WEB INS. 2800
66.00 2640
20 x 6.251 75.00 0.711 3000
24 x 6.255 86.00 0.505 3440
6.385 96.00 0.635 3840
7.060 80.00 0.660 3200
7.200 90.00 0.800 3600
7.000 100.00 0.500 4000
7.125 106.00 0.625 4240
7.245 121.00 0.745 4840
7.870 0.620
8.050 0.800

JR. BEAMS

Size Wt/Ft Wt/40’
6” 4.4 176
7” 5.5 220
8” 6.5 260
10” 8.0 320
10” 9.0 360
12” 11.8 472
14” 17.2 688

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
28 Inc. cannot be held liable for any inaccuracies.

PIPE DIMENSIONS AB

Size Inches O.D. Inches Shapes & Sizes
1/8 0.405
1/4 0.540
3/8 0.675
1/2 0.840
3/4 1.050
1 1.315
1 1/4 1.660
1 1/2 1.900
2 2.375
2 1/2 2.875
3 3.500
3 1/2 4.00
4 4.500
5 5.563
6 6.625
8 8.625
10 10.750
12 12.750
14 14.000
16 16.000
18 18.000
24 20.000
24.000

GAUGE PIPE A B

BARE UNCOATED STRAIGHT SEAM

OD GA Wall Wt/Ft
4 14 0.075 3.21
4 1/2 12 0.105 5.03
6 5/8 10 0.135 6.43
8 14 0.075 3.62
8 5/8 12 0.105 6.75
10 10 0.135 8.64
12 0.105 7.47
14 0.075 6.48
12 0.105 9.04
10 0.135 11.58
12 0.105 9.76
12 0.105 11.33
10 0.135 14.53

29

ANSI Pipe Schedule

PIPE SIZE O.D. IN 5S 5 10S 10 20 30 40S & STD 40 60 80S & E. H. 80
1/8 INCHES 0.035 0.049 0.049 0.068 0.068 0.095 0.095
1/4 0.405 0.065 0.1383 0.1863 0.1863 0.250 0.277 0.2447 0.2447 0.281 0.3145 0.3145
3/8 0.540 0.5383 0.049 0.065 0.065 22.36 24.70 0.088 0.088 12.68 0.119 0.119
1/2 0.675 0.065 0.2570 0.3297 0.3297 0.250 0.307 0.4248 0.4248 0.5351 0.5351
3/4 0.840 0.6838 0.049 0.065 0.065 28.04 34.24 0.091 0.091 0.406 0.126 0.126
1.050 0.065 0.3276 0.4235 0.4235 0.250 0.330 0.5676 0.5676 35.64 0.7388 0.7388
1 1.315 0.8678 0.065 0.083 0.083 33.38 43.77 0.109 0.109 0.500 0.147 0.147
1 1/4 1.660 0.065 0.5383 0.6710 0.6710 0.312 0.375 0.8510 0.8510 54.74 1.088 1.088
1 1/2 1.900 1.107 0.065 0.083 0.083 45.68 54.57 0.113 0.113 0.562 0.154 0.154
2 2.375 0.065 0.6838 0.8572 0.8572 0.312 0.375 1.131 1.131 73.16 1.474 1.474
2 1/2 2.875 1.274 0.065 0.109 0.109 52.36 62.58 0.133 0.133 0.593 0.179 0.179
3 0.065 0.8678 1.404 1.404 0.312 0.437 1.679 1.679 84.91 2.172 2.172
3 1/2 3.5 1.604 0.065 0.109 0.109 59.03 82.06 0.140 0.140 0.656 0.191 0.191
4 4.0 0.083 1.107 1.806 1.806 0.375 0.500 2.273 2.273 107.5 2.997 2.997
4 1/2 4.5 2.475 0.065 0.109 0.109 78.60 104.1 0.145 0.145 0.750 0.200 0.200
5 5.0 0.083 1.274 2.085 2.085 0.375 0.562 2.718 2.718 138.2 3.631 3.631
6 5.563 3.029 0.065 0.109 0.109 94.62 140.8 0.154 0.154 0.812 0.218 0.218
7 6.675 0.083 1.604 2.638 2.638 0.500 0.625 3.653 3.653 166.4 5.022 5.022
8 7.625 3.472 0.083 0.120 0.120 136.2 182.7 0.203 0.203 0.968 0.276 0.276
9 8.625 0.083 2.475 3.531 3.531 0.500 0.625 5.793 5.793 238.1 7.661 7.661
10 9.625 3.915 0.083 0.120 0.120 146.8 196.1 0.216 0.216 0.300 0.300
11 10.75 3.029 4.332 4.332 0.625 7.576 7.576 10.25 10.25
12 11.75 0.109 0.083 0.120 0.120 0.5 209.4 0.226 0.226 0.318 0.318
14 12.75 6.349 3.472 4.973 4.973 157.5 0.625 9.109 9.109 12.51 12.51
16 14.0 0.109 0.083 0.120 0.120 0.500 222.8 0.237 0.237 0.337 0.337
18 16.0 7.585 3.915 5.613 5.613 168.2 0.625 10.79 10.79 14.98 14.98
20 18.0 0.500 236.1 0.247 0.355
24 20.0 0.109 0.109 0.134 0.134 178.9 0.625 12.53 0.258 17.61 0.375
26 24.0 9.914 6.349 7.770 7.770 0.500 249.7 0.258 14.62 0.375 20.78
28 26.0 0.109 0.134 0.134 189.5 0.625 14.62 0.280 20.78 0.432
30 28.0 0.134 7.585 9.290 9.289 0.500 263.07 0.280 18.97 0.432 28.57
32 30.0 15.19 197.75 0.625 18.97 28.57
34 32.0 0.109 0.148 0.148 0.500 276.18 0.301 0.322 0.500 0.500
36 34.0 0.156 9.914 13.40 13.40 211.12 0.625 23.57 28.55 38.05 43.39
38 36.0 21.07 0.500 289.8 0.322 0.500
40 38.0 0.156 0.134 0.165 0.165 221.82 0.625 28.55 0.365 43.39 0.593
42 40.0 2307 15.19 18.65 18.70 0.500 303.16 0.342 40.48 0.500 64.33
44 42.0 0.165 232.51 0.625 33.90 48.72
46 44.0 27.9 0.165 0.180 0.180 0.500 316.5 0.365 0.406 0.500 0.687
48 46.0 0.165 22.18 24.16 24.20 243.2 40.48 53.53 54.74 88.51
60 48.0 31.43 0.188 0.250 0.500 0.375 0.437 0.500 0.750
60.0 0.188 27.73 36.71 253.89 45.55 63.37 60.07 106.1
39.78 0.188 0.250 0.375 0.500 0.500 0.843
0.218 31.75 42.05 49.56 82.77 65.42 136.5
55.37 0.188 0.250 0.375 0.562 0.500 0.937
35.76 47.39 54.57 104.8 72.09 170.8
0.218 0.250 0.375 0.593 0.500 1.031
46.05 52.73 62.58 122.9 82.77 208.9
0.250 0.250 0.375 0.687 0.500 1.218
63.41 63.41 70.59 171.2 93.45 296.4
0.312 0.375 0.500
85.60 78.60 0.688 104.1
0.312 0.375 230.1 0.500
92.26 94.62 0.688 125.5
0.312 0.375 244.8 0.500
98.93 102.6 0.750 136.2
0.312 0.375 282.3 0.500
105.6 110.6 146.8
0.344 0.375 0.750 0.500
123.7 118.6 330.4 157.5
0.312 0.375 0.500
118.9 126.7 168.2
0.375 0.500
134.7 178.9
0.375 0.500
142.7 189.6
0.375 0.500
150.8 200.4
0.375 0.500
158.85 211.13
0.375 0.500
166.7 221.82
0.375 0.500
174.9 232.6
0.375 0.500
182.9 243.2
0.375 0.500
190.7 253.89
0.375 0.500
238.8 317.7

Regular font: Wall thickness in inches
Bold font: Wt per ft. (pounds)

30

ANSI Pipe Schedule

O.D. IN VOLUME Shapes & Sizes
INC60HES DOUBLE CUBIC FEET
80 40S & STD PIPE40SIZE 80S5&SE. H. 580 1100S0 1200 12400 16300 4E0. SH.& STDPER FOO40T 60 80S & E. H. 8
095 0.068 0.405 0.095 00.0.03955 0.049 0.049 0.068 0.068 0.095 0.0
3145 0.214/847 0.3145 00.1.3318435 0.1863 0.1863 0.821520 0.2447 0.000.12447 0.281 0.3145 0.31
119 0.088 0.540 0.119 00.0.14199 0.065 0.065 6272.736 0.088 0.088 12.68 0.119 0.1
5351 0.412/4 8 0.5351 00.2.5537501 0.3297 0.3297 10.02050 0.4248 0.000.24248 0.5351 0.53
126 0.091 0.675 0.126 00.0.14296 0.065 0.065 12084.0.14 0.091 0.091 0.406 0.126 0.1
7388 0.536/876 0.7388 00.3.7237868 0.4235 0.4235 10.122550 0.5676 0.000.35676 35.64 0.7388 0.73
147 0.109 0.840 00..016457 00.0.16457 0.083 0.083 1339.3.78 0.187 0.209.4109 0.109 0.500 0.147 0.1
088 0.815/210 0.15.308838 0.6710 0.6710 10.235102 1.304 1.701.84510 0.000.58510 54.74 1.088 1.0
154 0.113 1.050 01.5.038883 00.0.1654 0.083 0.083 14750.6.28 0.218 0.300.8113 0.113 0.562 0.154 0.1
474 1.31/341 00..016554 0.16.843784 0.8572 0.8572 10.433172 1.937 2.414.131 0.0018.131 73.16 1.474 1.4
179 0.133 1.315 01.6.487348 00.0.16759 0.109 0.109 2523.3.56 0.250 0.305.8133 0.133 0.593 0.179 0.1
172 00..016759 0.28.617782 1.404 1.404 10.53612 2.844 3.615.9679 0.0112.679 84.91 2.172 2.1
191 1 1.679 1.660 02.8.167728 00.0.16951 0.109 0.109 25794.0.23 0.250 0.308.2140 0.140 0.656 0.191 0.1
997 0.140 00..016951 12.1.90977 1.806 1.806 10.735705 3.765 5.221.4273 0.0129.273 107.5 2.997 2.9
200 1.900 12..190977 00.0.26050 0.109 0.109 37481.6.10 0.281 0.400.0145 0.145 0.750 0.200 0.2
631 1 12/4.273 00..026050 13.2.67341 2.085 2.085 20.036725 4.859 6.420.8718 0.0225.718 138.2 3.631 3.6
218 0.145 2.375 13..267341 00.0.26158 0.109 0.109 49843.6.12 0.343 0.403.6154 0.154 0.812 0.218 0.2
022 00..026158 15.6.00242 2.638 2.638 0.500 7.444 9.032.9653 0.0339.653 166.4 5.022 5.0
276 1 12/2.718 2.875 15..600242 00.0.28736 0.120 0.120 136.2 0.375 0.505.203 0.203 0.968 0.276 0.2
661 0.154 00..028736 27.4.67651 3.531 3.531 0.500 10.01 13.57.0793 0.0557.793 238.1 7.661 7.6
300 3.5 27..467651 00.0.38030 0.120 0.120 146.8 0.437 0.600.0216 0.216 0.300 0.3
0.25 2 3.653 00..038030 31.002.295 4.332 4.332 14.32 18.75.8576 0.0875.576 10.25 10.
318 0.203 4.0 31.0.2295 00.0.38138 0.120 0.120 0.5 0.603.6226 0.226 0.318 0.3
2.51 0.281 00..038138 31.427.521 4.973 4.973 157.5 22.98.5109 0.191.109 12.51 12.
337 2 15/2.793 124..658 31.24.7521 00.0.3837 0.120 00..142307 0.500 0.531 0.607.4237 0.237 0.337 0.3
4.98 0.216 00..038337 31.941.958 5.613 51.96.1031 168.2 22.51 27.1504.79 0.1140.79 14.98 14.
5.0 31.49.1958 0.500 0.701.0247 0.355
375 3 7.576 0.355 00.1.30795 0.134 00..153040 178.9 321.523.53 0.17 17.61 0.3
0.78 0.226 5.563 17.61 62.304.798 7.770 72.7.7004 0.500 0.625 0.705.0258 0.258 0.375 20.
432 00..130795 00.1.40392 0.134 00..153642 189.5 32.96 381.545.62 0.2114.62 20.78 0.4
8.57 3 19/2.109 6.675 62.03.4798 72.588.557 9.290 93.62.8399 0.500 0.718 0.806.4280 0.280 0.432 28.
0.237 00..140392 197.75 45.3 53.1186.97 0.318.97 28.57
500 7.625 72.85.8557 00.1.50090 00.1.54983 00..174188 0.500 0.807.5301 0.500 0.5
3.39 4 10.79 0.406 0.500 94.931.349 1530.4.807 1630..4903 211.12 63.2038.57 0.4 38.05 43.
385.6.6245 38.05 0.500 00.9.20767 0.807.5322 0.322 0.500
593 4 1/2 00..150090 00.1.53943 00.1.76158 00..186453 221.82 7244.6.790 72.2482.55 0.5228.55 43.39 0.5
4.33 0.258 9.625 94.39.1349 1654.1.393 1786.6.953 1889..7200 0.500 0.342 0.500 64.
0.500 0.500 232.51 33.90 0.64 48.72
687 5 14.62 5140..745 48.72 00.1.6857 00.1.8403 01..108000 0.500 10.1.32057 0.365 0.365 0.500 0.6
8.51 0.280 00..153040 2828.1.581 2140.176.2 2142.52.05 243.2 13145..274 40.48 0.840.48 54.74 88.
750 11.75 1554..1794 00.1.98387 01..205903 0.500 0.375 0.500 0.7
06.1 6 18.97 0.562 0.500 0.750 2173.703.7 3165.07.17 253.89 45.55 0.96 60.07 106
843 7132..1765 60.07 106.1 01.1.08381 01..225108 10.3.31320 0.375 0.406 0.500 0.8
36.5 7 0.593 00..155060 0.843 3116.745.8 4129.20.53 14630..737 49.56 1.1533.53 65.42 136
937 0.322 8144.9.01 2615..0472 136.5 01.1.18586 01..235705 10.4.30765 0.375 0.437 0.500 0.9
70.8 0.656 00..155060 0.937 3250.786.0 4274.43.91 15849..517 54.57 1.3663.37 72.09 170
031 8 28.55 11067..05 27320.079 170.8 01.2.2180 01..255000 10.5.39735 0.375 0.500 0.500 1.0
08.9 0.750 0.500 1.031 4265.065.1 5229.67.34 26425..518 62.58 1.7882.77 82.77 208
218 9 11388..02 0.18625.277.9 208.9 01.2.5301 01..285102 10.7.48317 0.375 0.562 0.500 1.2
96.4 0.365 0.812 00..156050 1.218 6336.471.4 6432.94.14 38028..066 70.59 2.21504.8 93.45 296
12606..04 3913..4435 296.4 0.312 10.9.56080 0.375 0.593 0.500
10 40.48 0.968 00..158080 85.60 317094.0.1 78.60 2.71822.9 104.1
22348..01 3190.47.81 0.312 20.3.54632 0.375 0.687 0.500
11 00..251080 92.26 514410.9.8 94.62 4171.2 125.5
0.406 26.0 5152.53.75 0.312 0.375 0.500
0.500 98.93 102.6 4.7 136.2
12 53.53 28.0 136.2 0.312 0.625 0.375 0.500
0.437 0.500 105.6 182.7 110.6 5.4 146.8
30.0 146.8 0.344 0.500
14 63.37 0.500 123.7 0.625 0.375 157.5
0.500 32.0 157.5 0.312 196.1 118.6 6.25 0.500
0.500 118.9 168.2
16 82.77 34.0 168.2 0.625 0.375 0.688 0.500
0.562 0.500 209.4 126.7 7.1230.1 178.9
36.0 178.9 0.500
18 104.8 0.500 0.625 0.375 0.688 189.6
0.593 38.0 189.6 222.8 134.7 8.02344.8 0.500
0.500 200.4
20 122.9 40.0 200.4 0.625 0.375 0.750 0.500
0.687 0.500 236.1 142.7 9282.3 211.13
42.0 211.13 0.500
24 171.2 0.500 0.625 0.375 221.82
44.0 221.82 249.7 150.8 10.03 0.500
26 0.500 232.6
46.0 232.6 0.625 0.375 0.500
28 0.500 263.07 158.85 11.11 243.2
48.0 243.2 0.625 0.375 0.750 0.500
30 0.500 276.18 166.7 12.23530.4 253.89
0.688 60.0 253.89 0.500
0.500 0.625 0.375 317.7
32 230.1 317.7 289.8 174.9 13.44
0.688
0.625 0.375
34 244.8 303.16 182.9 14.69
0.750
0.625 0.375
36 282.3 316.5 190.7 16

38 0.375
238.8 25
40
0.750

42 330.4

44

46

48

60

Regular font: Wall thickness in inches 31
Bold font: Wt per ft. (pounds)

Gauge Pipe Schedule

0.1046 0.1345 0.188 0.250

O.D. PIPE IN INCHES 12 Gauge 10 Gauge 3/16" 1/4"
4.50
4 5.00 5.70 11.64 15.35
4 1/2 6.75 6.40 12.89 17.02
6 7.29 8.64 15.64 20.69
6 5/8 9.05 9.32 16.90 22.36
8 9.52 11.58 19.70 26.04
8 5/8 11.33 12.20 21.15 28.04
10 11.89 14.52 24.30 31.40
10 3/4 13.60 15.25 25.15 33.38
12 14.13 17.50 27.66 36.71
12 3/4 15.53 18.12 29.86 38.35
14 19.93 31.67 42.05
14 1/2 17.76 21.16 33.75 44.75
16 22.79 35.67 47.39
16 1/2 19.99 39.68 52.73
18 22.23 25.67 43.69 58.08
20 24.46 28.54 47.69 63.42
22 26.70 31.41
24 34.29

800.423.8016 | www.JimsSupply.com

32

AB

GAUGE PIPE Shapes & Sizes

BARE UNCOATED STRAIGHT SEAM

OD GA Wall Wt/Ft
10 3/4 12 0.105 12.19
12 12 0.105 13.62
12 3/4 10 0.135 17.47
14 12 0.105 14.48
14 12 0.105 15.92
16 10 0.135 20.42
12 0.105 18.21
18 10 0.135 23.36
7 0.180 31.67
12 0.105 20.50
10 0.135 26.31
7 0.180 35.67

PG & E BARRIER POSTS
• 4” SCH40 Galvanized Pipe
• Stationary and removable
• Plain End and Threaded
• Threaded Caps available
• All specs conform to PG & E requirements

800.423.8016 | www.JimsSupply.com

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
Inc. cannot be held liable for any inaccuracies.
33

34

Shapes & Sizes

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
Inc. cannot be held liable for any inaccuracies.
35

RECTANGULAR TUBING

Size GA. Thickness Lbs/Ft
3 x 1 11 0.120 3.050
3 x 1 1/2 14 0.083 2.390
11 0.120 3.480
3/16 0.188 4.960
3 1/2 x 1 1/2 14 0.083 2.670
3 x 2 14 0.083 2.670
11 0.120 3.900
3/16 0.188 5.590
1/4 0.250 7.110
4 x 2 14 0.083 3.230
11 0.120 4.750
3/16 0.188 6.870
1/4 0.250 8.810
5/16 0.312 10.580
4 x 3 14 0.083 3.800
11 0.120 5.600
3/16 0.188 8.150
1/4 0.250 10.510
5 x 2 11 0.120 5.600
3/16 0.188 8.150
1/4 0.250 10.510
5 x 3 11 0.120 6.450
3/16 0.188 9.420
1/4 0.250 12.210
5/16 0.312 14.830
3/8 0.375 17.270
5 x 4 3/16 0.188 10.700
1/4 0.250 13.910
6 x 2 11 0.120 6.450
3/16 0.188 9.420
1/4 0.250 12.210
5/16 0.312 14.830
3/8 0.375 17.270
6 x 3 3/16 0.188 10.700
1/4 0.250 13.910
5/16 0.312 16.960
3/8 0.375 19.820
6 x 4 3/16 0.188 11.970
1/4 0.250 15.620
5/16 0.312 19.080
3/8 0.375 22.370
1/2 0.500 28.430
7 x 5 3/16 0.188 14.530
1/4 0.250 19.020
7 x 5 5/16 0.312 23.340
3/8 0.375 27.480
36

RECTANGULAR TUBING

Size GA. Thickness Lbs/Ft Shapes & Sizes

1/2 0.500 35.240
8x2 3/16 0.188 11.970
1/4 0.250 15.620
8x3 3/16 0.188 13.250
1/4 0.250 17.320
3/8 0.375 24.930
8x4 3/16 0.188 14.530
1/4 0.250 19.020
5/16 0.312 23.340
3/8 0.375 27.480
1/2 0.500 35.240
8x6 3/16 0.188 17.080
1/4 0.250 22.420
5/16 0.312 27.590
3/8 0.375 32.580
1/2 0.500 42.050
10 x 2 3/16 0.188 14.530
1/4 0.250 19.020
3/8 0.375 27.480
10 x 3 1/4 0.250 20.720
10 x 4 1/4 0.250 22.420
3/8 0.375 32.580
10 x 6 3/16 0.188 19.630
1/4 0.250 25.820
3/8 0.375 37.690
10 x 8 1/4 0.250 29.230
5/16 0.312 36.100
12 x 2 3/16 0.188 17.080
1/4 0.250 22.420
12 x 3 3/16 0.188 18.350
12 x 4 1/4 0.250 25.820
12 x 6 1/4 0.250 29.230
5/16 0.312 36.100
1/6 0.375 42.790
12 x 8 1/4 0.250 32.630
3/8 0.375 47.900

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
Inc. cannot be held liable for any inaccuracies.
37

Size Inches Per Foot TUL BAR - HOLLOW
2 1/4 6.26 Weight - Pounds
21 ft 28 ft 32 ft 42 ft
131.46 175.28 200.32 262.92

Rd. Cornered Wt/Ft Wt/20' Wt/28' Wt/32' Wt/40' Wt/42’
Specialty Quality 17.27 344.52 482.33 551.23 689.04 723.49
2 1/4” Solid

CONCRETE REINFORCING BARS - GRADE 40 & 60

Bundle Quantity

Size #3 Wt/Ft Bundle Qty
3/8 #4 0.376 266
1/2 #5 0.668 150
5/8 #6 1.043 96
3/4 #7 1.502 66
7/8 #8 2.044 50
1 #9 2.670 37
1 1/8 #10 3.400 29
1 1/4 #11 4.303 23
1 3/8 5.313 18

WELDED WIRE MESH FABRIC

Mesh Gauge Rebar
6x6 10
6x6 8
6x6 6
6x6 4
4x 4 4
6x6 10
6x6 8
6x6 6
6x6 4
4x4 4

LADDER RUNGS - GALVANIZED - SMALL
Gauge Width Inches Height Inches Length Feet*
13 x 1.125 1.1625 60

LADDER RUNGS - STAINLESS STEEL - SMALL

Gauge Width Inches Height Inches Length Feet*
13 x 1.125 1.1625 60

LADDER RUNGS - HOT ROLLED - SMALL

Gauge Width Inches Height Inches Length Feet*
13 x 1.125 1.1625 60
38

Gauge LADDER RUNGS - GALVANIZED - LARGE Shapes & Sizes
13 x Width Inches Height Inches Length Feet*
1.5 2.25 60

Gauge LADDER RUNGS - STAINLESS STEEL- LARGE
13 x Width Inches Height Inches Length Feet*
Gauge 1.5 2.25 60
13 x
LADDER RUNGS - HOT ROLLED - LARGE
Width Inches Height Inches Length Feet*
1.5 2.25 60

EXPANDED METAL - RAISED Weight in
Center to Center Pounds/Sq Ft
Of Bonds
Thickness Plain Galv.
Style Designation Stock Sizes of Strand
1/4 No. 18 48 Width Length 1.14 1.71
1/2 No. 18 48 0.70 0.85
1/2 No. 16 48 x 96 0.255 1.00 0.048 0.86 0.97
1/2 No. 13 48 x 96 0.500 1.20 0.048 1.47 1.73
3/4 No. 16 48 x 96 0.500 1.20 0.060 0.54 0.65
3/4 No. 13 48 x 96 0.500 1.20 0.092 0.80 0.92
3/4 No. 10 48 x 96 0.923 2.00 0.060 1.20 1.36
3/4 No. 9 48 x 96 0.923 2.00 0.092 1.80 1.95
1 No. 16 48 x 96 0.923 2.00 0.092 0.44 0.51
1 1/2 No. 16 48 x 96 0.923 2.00 0.134 0.40 0.48
1 1/2 No. 13 48 x 96 1.090 2.40 0.060 0.60 0.68
1 1/2 No. 10 48 x 96 1.330 3.00 0.060 0.79 0.89
1 1/2 No. 9 48 x 96 1.330 3.00 0.092 1.20 1.31
1 1/2 No. 6 48 x 96 1.330 3.00 0.092 2.50 2.73
2 No. 9 48 x 96 1.330 3.00 0.134 0.90 1.02
x 96 1.330 3.00 0.198
x 96 1.850 4.00 0.134

EXPANDED METAL - FLATTENED

Style Designation Stock Sizes Center to Center Thickness Weight in
1/4 No. 20 48 x 96 Of Bonds of Strand Pounds/Sq Ft
1/4 No. 18 48 x 96 0.030
1/2 No. 20 48 x 96 Width Length 0.040 Plain Galv.
1/2 No. 18 48 x 96 0.029
1/2 No. 16 48 x 96 0.255 1.03 0.039 0.83 1.24
1/2 No. 13 48 x 96 0.255 1.03 0.050 1.11 1.65
3/4 No. 16 48 x 96 0.500 1.26 0.070 0.40 0.51
3/4 No. 14 48 x 96 0.500 1.26 0.048 0.66 0.88
3/4 No. 13 48 x 96 0.500 1.26 0.061 0.82 1.00
3/4 No. 9 48 x 96 0.500 1.26 0.070 1.40 1.62
3/4 No. 9 48 x 120 0.923 2.10 0.120 0.51 0.61
3/4 No. 9 48 x 144 0.923 2.12 0.120 0.63 0.75
1 No. 16 48 x 96 0.923 2.10 0.120 0.76 0.86
1 1/2 No. 13 48 x 96 0.923 2.12 0.048 1.71 1.86
1 1/2 No. 9 48 x 96 0.923 2.12 0.070 1.71 1.86
1 1/2 No. 6 48 x 96 0.923 2.12 0.110 1.71 1.86
1.090 2.56 0.198 0.41 0.50
1.330 3.20 0.57 0.68
1.330 3.20 1.11 1.28
1.330 3.00 02.50 2.73

39

EXPANDED METAL - GRATING

Center to Center Weight in
Of Bonds
Stock Sizes Pounds/Sq Ft
3.0 LB 48 x
3.14 LB 48 x Width Length Plain Galv.
3.14 LB 48 x
4.0 LB 48 x 120 1.33 5.33 3.00 3.20
4.0 LB 48 x 96 2.00 6.00 3.14 3.34
4.27 LB 48 x 120 2.00 6.00 3.14 3.34 Flattened Expanded Metal
5.0 LB 48 x 96 1.33 5.33 4.00 4.30 Raised Expanded Metal
5.0 LB 48 x 120 1.33 5.33 4.00 4.30
6.25 LB 48 x 96 1.41 4.00 4.27 4.57
96 1.33 5.33 5.00 5.50
120 1.33 5.33 5.00 5.50
96 1.41 5.33 6.25 6.85

GRIP STRUT

Gauge Width Inches Height Inches Length Feet*
12 x 4 3/4 1 1/2 10,12
7 1 1/2 10,12
x 9 1/2 1 1/2 10,12
x 11 3/4 1 1/2 10,12
x 18 3/4 1 1/2 10,12
x 24 1 1/2 10,12
x 4 3/4 2 10,12
12 x 7 2 10,12
x 9 1/2 2 10,12
x 11 3/4 2 10,12
x 18 3/4 2 10,12
x 24 2 10,12
x 4 3/4 1 1/2 10,12
14 x 7 1 1/2 10,12
x 9 1/2 1 1/2 10,12
x 11 3/4 1 1/2 10,12
x 18 3/4 1 1/2 10,12
x 24 1 1/2 10,12
x 4 3/4 2 10,12
14 x 7 2 10,12
x 9 1/2 2 10,12
x 11 3/4 2 10,12
x 18 3/4 2 10,12
x 24 2 10,12
x

*OR CUT-TO-SIZE
Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
40 Inc. cannot be held liable for any inaccuracies.

General Information
HOT ROLLED BAR PRODUCTS

Commercial Quality

ASTM-A36

Hot rolled, ASTM-A36 bars are produced by steelmaking methods that result in a sound

tions. ASTM-A36 material is suitable for most construction purposes including riveted, bolted
and welded structures. Material that is made to ASTM-A36 is suitable for mild hot and cold

Carbon Manganese Phosphorus Sulfur General Information
(Max.) (Max.) (Max.) .05
.26 - .29 .60 - .90 .04

Mechanical Properties

Tensile Yield Point Elongation Brinell
Strength (P.S.I) In 2” Hardness (BHN)
(P.S.I) 36,000 23% 137
58,000-65,000

Weldability
Hot rolled A36 bars present no welding problems when using all welding processes. The

tions are dependent on welding conditions such as the thickness of the sections to be
welded, service requirements and design.

ASTM-A572 GRADE 50

High tensile bars are rolled by various steel mills. They are a high strength, low alloy material,
intended primarily for weight reduction, or longer life, by means of greater strength.

Analysis (typical) Phosphorus Sulfur Silicon Cb.
Carbon Manganese .04 Max .05 Max .30 Max .01 Min.

Gr. 50 .21 Max 1.35 Max

Mechanical Properties (typical) Elongation
Tensile Strength Yield Point in 2”
(P.S.I) (P.S.I)
Gr. 50 65,000 Min. Min. 23%
50,000

800.423.8016 | www.JimsSupply.com 41

SPECIAL QUALITY BAR PRODUCTS

CHROMIUM-MOLYBDENUM ROUNDS
4140 HR, Heat Treated and CR, Heat Treated

(to 3” Diameter)
Machine Straightened and Stress Relieved

A balanced composition and careful hardening treatment gives this steel high strength and
uniformly high physicals. The resultant steel has excellent tensile strength with good ductility
giving better shock and impact resistance.

It machines more freely than other steel in its class, enabling the speedy production of
hardened parts without additional heat treatment. This steel is particularly suitable for oil

-
ments.

Analysis

Carbon Manganese Phosphorus Sulfur Silicon Chromium Molybdenum
40-.45 .75-1.00 .04 Max. .04 Max. .20-.35 .80-1.10 .15-.25

Applications
Heavy duty shafts, axles, pins, studs, bolts, couplings, oil well tool joints, winch shafts, piston
rods, stay bolts, tractor arms, spindles, sprockets.

Typical Mechanical Properties % Reduction
Tensile Strength Yield Point Elongation Of Area
(P.S.I) (P.S.I) In 2” 45
125,000 105,000 16%

Weldability
This grade can be welded by any common welding process if the section is pre-heated, and
stress relieved after welding. Welding rod grade is dependent upon design, service require-
ment, and thickness of sections.

To Normalize Heat to 1600º - 1700ºF and/or cool in air.

To Anneal Heat to 1450º - 1550ºF Cool in furnace slowly.

To Harden Hardening temperature ranges from 1550º - 1600ºF. Use oil as the
quenching medium.

STRESSPROOF COLD FINISHED SHAFTING
This is a severely cold worked, strain relieved carbon killed steel bar. It is available as a Cold
Drawn Bar in 12 foot lengths. Some locations stock an ASTM-1144 bar with similar properties.

Analysis Manganese Sulfur Silicon
Carbon 1.35-1.65 .24-.33 .15-.30
.40-.48

42

Applications
Ideal for general maintenance and repair, as all properties are “built in” the bar. Production
parts include axles, collets, gears, spline shafts, spindles, pump shafts, feed and lead screws to
all kinds, worms, studs, etc.

Machinability

Cutting speeds of about 125 surface feet per minute are recommended.

Mechanical Properties Min. Yield Point Average Tensile Strength General Information
Size In Inches 100,000 p.s.i. 125,000 p.s.i.
1/2” to 2” 90,000 p.s.i. 120,000 p.s.i.
Over 2” to 3 ¼”

Tolerances Cold Drawn (Plus) Cold Drawn (Minus)
Size In Inches 0.000 0.004
5/16 to 1 ½” 0.000 0.005
1 ½ to 2 ½” 0.000 0.006
2 ¼ to 4”

Warpage
Almost completely free from strains, it may be splined, key seated, broached, drilled, reamed,
milled or threaded. Expensive straightening operations are eliminated

Wearability
Although easily machined, wear resistant properties are unusually high. Many heat treated or
carburized parts have been successfully replaced by unhardened Stress proof in spite of its
relative softness.

Reduced Costs
By eliminating hardening and straightening operations, reducing machining time, lowering

STRESSPROOF will give you reductions in costs on many parts. While the price is slightly
higher than ordinary carbon bars, its increased strength, wearability and service life make it
the most economical steel to use in may applications.

PRECISION C-1045 SHAFTING
Precision Shafting represents the highest degree of straightness, accuracy, concentricity and
surface perfection obtainable in commercial practice. These bars are turned and center less

is important to note that turning does not alter the physical properties of the bar.

Analysis

C-1045 .43-.50 .60-.90 .04 Max. .05 Max.

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
Inc. cannot be held liable for any inaccuracies.
43

Application
This steel is often called pump rod or pump shafting due to its high degree of straightness
(important in high speed shafting). The special straightness serves to prevent vibrations and
wear on packings and bearings which must be avoided in deep well pump work. Other uses
include motor shafts and other applications where high speed work necessitates straightness
and accuracy along with the ability to be machined unsymmetrically with practically no
danger of warpage.

Typical Mechanical Properties

C-1045 (P.S.I) (P.S.I) In 2 Area
110,000 78,000 20% 55

Tolerances
Diameter of Bar Plus Tolerance Minus Tolerance
Less than 1 ½” 0 .001”
1 ½”To Under 2 ½” 0 .0015”
2 ½”To 3” Inclusive 0 .002”
Over 3”To 4” Inclusive 0 .003”

SCREW MACHINE STOCK
C-12L14 Cold Finished Rounds
These special quality CF rounds have a machinability rating on automatic screw machines of
300 surface feet per minute. These rounds are of screw stock quality used for instruments,
electronic parts, and machine shafts. They are also suitable for nickel plating.

Analysis

C-12L14 .15 Max .085-1.15 .04-.09 .26-.35 .15-.35

HOT ROLLED TUL BARS

This is a high carbon special quality steel with greater strength in the as-rolled condition than
lower carbon grades.
Analysis
Carbon Manganese Phosphorus Sulfur
.65-.75 .60-.90 .04 Max. .05 Max.

Applications
C1070 bars are used primarily in the manufacturing and repair of farm implements where
high strength is required.

Typical Mechanical Properties
Tensile Yield Elongation Reduction Brinell
Strength Point In 2” of Area Hardness
(P.S.I) (P.S.I) 12% 255
126,000 65,000 23%

Machinability

in the as-rolled state.

44

Weldability
C1070 steel is not readily weldable due to its high carbon content. However, gas or arc
equivalent strength in the weld. Stress relieving is also recommended. Welding rod grade
depends on design, service requirements, and thickness of material.

SHEET PRODUCTS

STAINLESS STEEL

Non-Magnetic, Non-Hardening, Chrome Nickel Steels General Information

303 A free machining version of T-304. Corrosion resistance andphysical properties only
slightly less than T-304.

304 The most popular of all stainless steels, exhibiting good corrosion resistance, ease of
welding and good formability.

304L Lower carbon version of T-304. Used to minimize carbide precipitation when welded.
Physical properties somewhat less than T-304.

316 Having superior corrosion resistance to pitting and higher strength at elevated
temperatures than T-304. It is used frequently in marine applications. Resistant to
creep at high temperatures.

316L Lower carbon content to minimize carbon precipitation when welding.

321 Stabilized for use where post weld annealing is not possible. Corrosion resistance
similar to T-304.

310 Heat resistant grade resists scaling up to 2050°F. Good resistance to thermal fatigue
due to cyclic heating.

Sheet & Plate Finishes

HRAP/No. 1 Hot rolled, annealed, and descaled. Produced by hot rolling to speci ed
thickness followed by annealing and descaling. Generally used in industrial
applications, such as for heat and corrosion resistance, where smoothness
or nish is not of particular importance.

No. 2b Cold rolled, bright nish. Commonly produced the same as 2D except that
the annealed and descaled sheet receives a nal light cold rolled nish pass
on the polished roll. This is a general purpose cold rolled nish. It is
commonly used for all but di cult deep, drawing applications.

No. 4 General purpose polished nish, one or both sides. Widely used for
restaurant equipment, kitchen equipment, store fronts, dairy equipment,
etc.

No. 8 The most re ective nish that is commonly produced, sometimes called a
mirror nish. It is obtained by polishing with successively ner abrasives
and bu ng extensively with very ne bu ng rouges. The surface is
essentially free of grit lines from preliminary grinding operations. The nish
is most widely used for press plates, as well as for small mirrors and
re ectors.

45

PLATE PRODUCTS
Hot Rolled ASTM-A36
Hot rolled plates made to ASTM-A36 are intended for use in structural applications.

cutting is necessary when plate thickness exceeds mill shearing limits.

Analysis Carbon Manganese Phosphorus Sulfur Silicon
Thickness .25 Max .80/1.20 .04 Max .05 Max -
To 3/4” .25 Max .80/1.20 .04 Max .05 Max -
3/4 - 1 1/2” .25 Max .80/1.20 .04 Max .05 Max .15/.30
1 1/2” - 2 1/2” .27 Max .85/1.20 .04 Max .05 Max .15/.30
2 1/2” - 4” .29 Max .85/1.20 .04 Max .05 Max .15/.30
4” & Up

Applications
Carbon steel plates have so many and such varied uses that a comprehensive list of
plate applications would be impossible in these pages. However, a few uses are: tanks,
tubes, truck frames, railroad cars, as well as many structural uses, such as base plates,
girders, etc.

Mechanical Properties Elongation
Tensile Strength Yield Point
(P.S.I.) (P.S.I.) in 8 inches
58,000 36,000 Minimum* 20%
*Yield Point 32,000 P.S.I. for plates over 8 inches thick.

Machinability
This grade is satisfactory for ordinary machining or drilling, but it is not considered a free
machining grade.

Weldability
These grades present no problems when using all welding processes. The quality is gener-

such as the thickness of the sections to be welded, service requirements, and design.

UNIVERSAL MILL PLATES

more in thickness. Universal Mill Plates are rolled between both horizontal and vertical rolls,
producing straight, almost perfectly parallel rolled edges.

Analysis Carbon Manganese Phosphorus Sulfur

A-36 .25 Max .80 - 1.20 .04 Max .05 Max.
A-529 Gr. 50 .27 Max 1.35 Max. .04 Max .05 Max.

Applications
These plates are used for base plates, cover plates and a wide variety of uses where long

46Plates are not recommended for lengthwise bending or breaking, such as formed channels.

A-36 Tensile Strength Yield Point Elongation
A-529 Gr. 50 (P.S.I) (P.S.I) In 8 inches

58,000-80,000 36,000 Min. 20%
70,000-100,000 50,000 Min. 18%

Machinability
This is not considered a free machining grade, although it is satisfactory for moderate
machining operations.

ABRASION RESISTANT STEEL PLATES General Information

“As Rolled” Abrasion Resistant Steel, also called A-R Steel, was developed to meet the many
demands for a low cost abrasion resisting steel for the materials handling industry.

Analysis Manganese Phosphorus Sulfur Silicon
Carbon 1.50 2.00 .05 Max. .055 Max. .15 - .35
.35 - .50

Applications
In general, any member of a steel structure requiring material with exceptional resistance to
abrasion, by either wet or dry materials, is considered a suitable application of A-R steel.
Unusually long life has been obtained by using A-R in a variety of parts including wear plates,
conveyor chutes, dredge pipes, screens, mixer drums, buckets and liner plates. Other
applications include scrap metal baling machines, gravel crushers, hoppers, farm implements,
railroad cars, and grader, mixer and scraper blades.

800.423.8016 | www.JimsSupply.com

Disclaimer: The weights listed in this catalog may vary depending on producing
mill. Every e ort has been made for accuracy. However, Jim’s Supply Company,
Inc. cannot be held liable for any inaccuracies.
47

Typical Mechanical Properties Elongation Reduction Brinell
Tensile Yield In of Hardness
Strength Point Area
(P.S.I) (P.S.I) 8 inches 35% 235
115,000 70,000 16%

Shearing
A-R Steel has higher hardness than structural carbon steel and shearing must be done with

you with heat number and source-mill information so that you can obtain accurate informa-
tion from the producing mill prior to any attempt to shear this material.

Flame Cutting

ensure the safety of workers and the integrity of the parts. To ensure proper safety and the
mill information so that you can obtain accurate information from the producing mill prior to

Punching
A-R Steel can be punched successfully in thicknesses up to ½” at temperatures not lower than
room temperature, but more power is required than for an equal thickness of mild structural
after punching. When holes are close together, as in the case of perforated screens, it is
necessary to preheat before punching or to resort to drilling. If these precautions are not
taken, it is possible that cracks may occur and may extend from one hole to the next. To
with heat number and source-mill information so that you can obtain accurate information
from the producing mill prior to punching this material.
Drilling and Machinability
This steel can be drilled and machined satisfactorily with standard equipment. However,
machine speeds and feeds must be reduced. High-speed drills are necessary and should be
kept cool with drilling compounds such as soluble oil or turpentine. For drilling this steel the
clearance rake of the drills should be less than that for steels of lower hardness.
Weldability
Abrasion Resistant Steel may be welded with proper precautions. Preheating is recom-
mended and after welding it is good practice to stress relieve or normalize. To normalize, heat
to 1650º and allow to cool slowly in air. Normalizing is sometimes omitted when the welded
part is not subject to severe vibration and stress. However, normalizing will prevent cracks,
give uniform structure and will not reduce the abrasive-resisting qualities. The grade of
welding rod to be used depends upon the thickness of section, designs, service require-
ments, etc.
heat number and source-mill information so that you can obtain accurate information from
the producing mill prior to punching this material.

High Brinell or Wear Plates are made from heat treated, high strength, abrasion resisting
steels.

48


Click to View FlipBook Version