N - Fall Protection

Fall Protection

FALL PROTECTION
& RESCUE

Index N2
N7
Donning Harness Video N22-N23
Fall Arrest Lanyards N3-N6
Ground Tents & Umbrellas N2
Harnesses N6
Harness Sizing Information N24
Harness Tips N8
Karabiners N24
Lanyard & Anchorage Tips N15
Maillons N24
Manhole Guard & Accessories
Pulleys N9-N14,
Rescue, Safety, Lifelines N16-N17, N24
N18-N21
& Accessories

Ventilators & Accessories

FALL PROTECTION & RESCUE

N2 Bashlin Harness Sizing & Video

FALL PROTECTION Bashlin Harness Sizing
& RESCUE
Harness ANSI ASTM Requirements - Bashlin’s harnesses meet
or exceed the ANSI and ASTM requirements for Fall Protection.
This includes the proposed ASTM revision of the F887 standard
specifying the minimum requirements for resistance to electric
arc. The standard 10,000 pound test nylon webbing used in
Bashlin Harnesses will endure an ARC flash of 50 cal/cm2, and
the harness will still pass the drop test outlined in the ASTM
specification. For complete information, including test reports,
contact your American Safety representative.

Sizing Bashlin Harnesses - The Bashlin harness is sized
according to the torso of the individual. This involves measuring
the height and the chest, then finding the correct size on the
chart, according to the style of the harness. Height is the first
consideration. However, if the chest measurement is too large for
the corresponding height, move to the larger size. If the chest
measurement is too small for the corresponding height, choose
the size dictated by the height.

Harness sizing chart by style.

662A & 662R Series Harness

Size Height Chest

“O” One size fits most 5’4” - 6’3” 34” - 48”
“X” Extra Large 6’3” - 6’6” 48” - 54”
“2XL” Double Extra Large 6’6” + 54” +

664 Series Harness

Size Height Chest

1. The user must be properly trained prior to using “S” Small 5’4” - 5’7” 34” - 36”
Bashlin products. “M” Medium 5’8” - 5’11” 38” - 48”
“L” Large 6’ - 6’3” 48” - 58”
2. Use the proper product for the job. “XL” Extra Large 6’3” + 58” +
3. Inspect the harness before each use.
4. Wear the harness tight. It must be tight enough that 683X Series Harness

the buckles hold the material properly and will not Size Height Chest
disengage accidentally. If the harness is loose, the
material can hook on items in the work area, or in the “S” Small 5’4” - 5’7” 34” - 36”
worst case will not perform properly in the event of an “M” Medium 5’8” - 5’11” 36” - 40”
arrested fall. “L” Large 6’ - 6’3” 42” - 44”
5. Check the buckles, and tighten the straps each time “X” Extra Large 6’4” - 6’6” 46” - 48”
before going aloft. “2X” Double Extra Large 6’6” + 48” - 52”
6. Store the harness properly in a storage bag for “3X” Triple Extra Large 6’6” + 52” +
longer wear.

A. Bashlin harnesses must be sized and
adjusted properly to function properly.
www.americansafety.com
Bashlin Harness Video

A. Donning Bashlin Harness Video - For additional information,
request our video “Donning Bashlin Harnesses”. This 17 minute
video provides the user basics on the use of the full body harness.
Contact customer service for more information.

24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE

N3Bashlin X Harnesses

Bashlin’s 683 Premier Harness. Features a cross-over style Option XC Option XA FALL PROTECTION
that adds comfort for the wearer. For utility work, the “X” style & RESCUE
keeps hardware low on the torso. The front loop is for working
positioning, or rescue.

Size Height Chest
“S” Small 5’4” - 5’7” 34” - 36”
“M” Medium 5’8” - 5’11” 36” - 40”
“L” Large 6’ - 6’3” 42” - 44”
“X” Extra Large 6’4” - 6’6” 46” - 48”
“2X” Double X-Large 6’6” + 48” - 52”
“3X” Triple X-Large 6’6” + 52” +

NOTE: Add ”E” to end of part # before size for nylon coated
hardware. Nylon coated hardware protects from static discharge.

“X” Harness with D-Ring Back Attachment - “X” style full body
harness with a 3” “D”.

Cat. No. Description Ship. Wt. Option XD
683XD Harness (Size) 4 lbs.
683GD w/grommet leg straps (Size)
4.5 lbs.

“X” Harness with Nylon Loop Back Attachment - “X” style full
body harness featuring a 3” nylon loop for lanyard attachment.
This can be used with a web loop or carabiner.

Cat. No. Description Ship. Wt.
683XA Harness (Size) 3.5 lbs.
683GA w/grommet leg straps (Size) 4 lbs.

“X” Harness with 24” Extension Back Attachment - “X” style 683XCE
full body harness includes a 24” extension back attachment. This 683XDL
is available with a D-ring(683XC), or without the D-Ring(683XB).
The maximum lanyard length is 4 ft.

Cat. No. Description Ship. Wt. 683GA
683XB Harness (Size) 3.5 lbs.
683GB Harness (Size) 4 lbs. 683XC
683XC Harness (Size) 3.5 lbs.
683GC Harness (Size) 4 lbs. B.

“X” Harness with Nylon Coated Hardware - Bashlin offers nylon
coating of the hardware for user protection from static discharge.
This is a wear resistant powder coating with excellent physical and
dielectric properties.

Cat. No. Description Ship. Wt.
683XDE Harness (Size) 4 lbs.
683XAE Harness (Size)
683XBE 4’ Max. lanyard length (Size) 3.5 lbs.
683XCE 4’ Max. lanyard length (Size) 3.5 lbs.
3.5 lbs.

“X” Harness with Plastisol Hardware Covers - The high-
dielectric dip-molded covers are resilient and have excellent
resistance to abrasion. They provide static protection and are
flame resistant to an electric arc.

Cat. No. Description Ship. Wt.
683XDL Harness (Size) 5 lbs.
683XAL Harness (Size)
683XBL 4’ Max. lanyard length (Size) 4.5 lbs.
683XCL 4’ Max. lanyard length (Size) 4.5 lbs.
4.5 lbs.

B. Quick Release Harnesses - All Bashlin Harnesses are
available with 2 piece quick release buckles. These buckles snap
together, and are easily released by squeezing the two ears.
These buckles meet ANSI/ASTM requirements.

Cat. No. Size Ship. Wt.
Q683 Harness (Size) 4 lbs.
Q662 One Size Fits Most
4.5 lbs

[email protected] Call Toll Free (800) 438-6013

FALL PROTECTION & RESCUE

N4 Bashlin Full Body Harness Options

FALL PROTECTION A. Back Attachment Options (Letter/Number 5)
& RESCUE C. Bashlin offers 2 basic styles of back attachments:
The “A” and “D” rest between the shoulder blades.
B. The “B” and “C” are 24” extension back attachments.
A - 3” nylon loop
Lanyards may be connected to D-Rings B - 24” over the shoulder extension with a 3” reinforced
on harnesses (“D/C”) with web/rope
loops, and properly dimensioned loop end. #1990
carabiners or snaphooks. Nylon back C - 24” over the shoulder extension with a small D-Ring.
attachments, (“A/B”) require web/rope D - Standard 3” industrial D-Ring

loops or properly dimensioned carabiners. Other Popular Harness Options
Snaphooks are not to be used with A/B (Letter/Numbers 6 through Size)
attachment points.
Quick Release Buckles
L. Q - Body Harness Buckles - Add Q to part number
D. E.
Static Protection for Hardware:
F. E - Nylon coated buckles
F - Leather pads under buckles
L - Plastisol buckle covers

Color Coded Tabs for Easier
Donning:
K - Color coated buckle tabs

Hip Positioning D-Rings on the Q.

Harness:
H - Positioning D-Rings

K. Pads for the Legs and Shoulders:
G - Leg Pads - nylon (Not Shown)
N - Shoulder pads - nylon

Rappel Seat Built into the N.
Harness:
R - Rappel seat

H. Shoulder Attachment for Confined
Space:
S - Shoulder D-Rings
T - Nylon shoulder loops.
S.
Size: Use the last Letters/Numbers

R.

T. The maximum and standard length for
Bashlin 2000 Series fall arrest lanyard
Limiting the lanyard length to 6 feet will
not ensure a free fall of 6 feet or less. The is 6 feet. This is to aid the user in
compliance with OSHA’s maximum 6 feet
lanyard length, anchor point, and work free fall for personal fall arrest systems.
location together will determine the For harnesses with B & C attachments,
free fall distance.
the lanyard must be 4 feet or less.
www.americansafety.com
24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE

N5Bashlin Climbing Harnesses

Bashlin’s Climbing Harness combines a full body harness with 683XAP
a Bashlin tool belt for maximum comfort and utility. They can be
used for various applications including poles and towers. Note that FALL PROTECTION
a “D” size is required. These climbing harnesses meet the ASTM & RESCUE
and ANSI requirements for work positioning, climbing, and fall
arrest. The 76 and 1511N meet the ASTM requirements and are
U.L. Classified to applicable OSHA Standards for line belts.

683X Style Climbing Harness - The “X” style harness is available
with the 656CM tool belt. This belt can be easily removed from
the harness when it is not needed. The harness features a front
attachment point for work positioning on ladders or rescue. Please
state size, “D” size.

Cat. No. Description Ship. Wt. 662ID
683XDP with 3” D-ring 8 lbs. 662KC
683XAP with nylon loop 8 lbs.
683XBP with 24” loop extension* 8 lbs.
683XCP with 24” D-ring extension* 8 lbs.

Add “Q” before harness part number to add Quick Release
Buckles to harness.
* Maximum lanyard length of 4’.

662 Harness with Belt Attachment - The harness has
attachment points for the belt on the outside of the harness. The
body belt attaches to the harness with straps and clips. There is
no strength rating for the belt attachment points. This harness has
a vertically moveable chest strap and standard leg adjustment. All
of the standard back attachments and grommet leg straps are also
available. The belt is not included with D-ring. (Ship. Wt. 4.5 lbs.)

Cat. No. 662ID

662A Style Climbing Harness

Here is a one size fits most harness with an attached tool belt. The
chest strap is movable. The webbing and hardware are standard.
Other back attachments are available.

Cat. No. Description Ship. Wt.
662KC 1511N with 24” D-ring extension 9 lbs.
662EC 76 with 24” D-ring extension
662TC 656CM with 24” D-ring extension 10 lbs.
8.5 lbs.

A. 656CM Tool Belt - This is a light, versatile belt. It can be used
with a harness or by itself in work positioning applications. The
pad is a Coolmax foam. The lining draws away perspiration. Order
by “D” size. (Ship. Wt. 4 lbs.)

Cat. No. 656CM A.

B. Quick Release Buckles - All Bashlin Harnesses are available B.
with 2 piece quick release buckles. These buckles snap together,
and are easily released by squeezing the two ears. These buckles Call Toll Free (800) 438-6013
meet ANSI/ASTM requirements. Add Q to beginning of part
number for buckles. Ex. Q656CM

[email protected]

N6 FALL PROTECTION & RESCUE

Self Rescue Harness & Harness Tips

FALL PROTECTION A. Bashlin’s Self Rescue Harness is a comfortable harness
& RESCUE for use in aerial devices and includes a complete system for self
rescue in the event of an arrested fall or the failure of the lift. The
lightweight compact rescue pack is attached to the back of the
harness just below the back attachment point. When the harness
is worn, the 2 lb. pack that is just over an inch thick lays in the
small of the back out of the way, but always available if needed.
It includes a short ladder for orthostatic relief in the event of an
arrested fall. If no other help is available the kit includes 75 feet
of 3/8” Kevlar line with a descent device for the worker to lower

A. himself to the ground.

Cat. No. SR683XC28

B. D. Harness Tips
C.
H. Tips for Use, Inspection, Care and Maintenance of Bashlin
E. I. Harnesses
F. • Read, understand, and follow all of the instructions included with the
harness or affixed to the harness prior to use. Do not use equipment
J. without proper training. (B)
• Check all buckles and closures for correct alignment, and that pass
G. through buckles are mated properly. Tuck excess webbing into the elastic
bands on the harness. This reduces the possibility of hooking the material
www.americansafety.com on an object, causing an accident. (C)
• The harness must be sized properly to perform correctly. Refer to the
sizing instructions. Do not use an improperly sized harness. (D)
• The harness back attachment is to be positioned between the shoulder
blades for peak performance during an arrested fall. Correct positioning
of the back attachment will also keep the straps from falling off the
shoulders during normal weather. (E)
• Wear the harness tight. It must be tight enough that the buckles hold
the material properly and will not disengage accidentally. A loose
harness is hazardous, and may not perform properly to arrest a fall.
• Avoid exposing the harness to substances or environments, such
as petroleum products, excessive heat, or prolonged sunlight that
will degrade the material or cause the friction buckles to slip.
• Nylon webbing melts at 400 degrees Fahrenheit and will begin to
degrade at lower temperatures. Remember this when working around
heat. Any nylon harness exposed to damaging heat must be removed
from service. (F)
• A harness storage bag, Bashlin #10HB or #10BM, will protect the
harness from most mechanical or chemical damage, and prolong the
life of the harness. (G)
• Altering this harness in any way voids the manufacturer’s warranty.
• The average useful life of a full body harness is 2 years from the
in service date or 3 years from the date of manufacture, which ever
comes first.
Inspecting Your Bashlin Harness
This harness must be inspected prior to every use. Remove this
harness from service if you notice any of the following:
1. Safety hardware which has electrical burns, cracks, or deformities.
2. Strength members which are worn, cut, abraded, or have suffered

chemical or thermal degradation. (H)
3. Sewing or splices which are torn, cut, or have broken stitches. (I)
Maintaining Your Bashlin Harness
Caring for this harness is easy and will take very little time. Please
observe the following instructions for best results:
• (J) Cleaning should be done with a mild soap and water. We suggest
placing the harness in a mesh bag (Bashlin #10HBM) and then in a clothes
washer on a gentle cycle, or you may simply hand wash with soap and
water. Never use a petroleum-based cleaner, as it will degrade the nylon.
Dry the harness by hanging; do not place in a clothes dryer.
• (G) Storage should be away from the sun, but with enough ventilation so
that the nylon does not mold or mildew. Do not store close to heat which
will dry the nylon.

24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE N7

Bashlin Fall Arrest Lanyards

2000 Series - Polyester Shock Absorbing Core, 6’ Long - 1”
tubular nylon web with polyester shock absorbing core.

K. 2000 Series Fall Arrest Lanyard with Two 6650 snaphooks. FALL PROTECTION
& RESCUE
(Ship. Wt 1.5 lbs.) K.

Cat. No. 2804-6HL

L. 2000 Series Fall Arrest Lanyard with One 6650 snaphook L.
and a loop end. (Ship. Wt. 1.5 lbs.)

Cat. No. 2805-6HL

M. 2000 Series Fall Arrest Lanyard with One 6650 snaphook
and a 3005A carabiner. (Ship. Wt. 2 lbs.)

Cat. No. 2815-6HL M.

N. 2000 Series Fall Arrest Lanyard with One 6650 snaphook
and a 5394 large snaphook. (Ship. Wt. 3.5 lbs.)

Cat. No. 2802-6HL N.

O. 2000 Series Fall Arrest Lanyard with One 6650 snaphook
and a 5386 medium snaphook. (Ship. Wt. 3 lbs.)

Cat. No. 2803-6HL
——————————
O.

Polyester Shock Absorbing Core Style “Y” Climbing Lanyard P.
- 6’ overall length, 1” tubular nylon web with shock absorbing core Q.
on the legs and 5394 medium ladder snap on the ends.

P. “Y” Climbing Lanyard with web hook on the yoke.

(Ship. Wt. 5 lbs.)

Cat. No. 2827-6

Q. “Y” Climbing Lanyard with 6650 rope snap on the yoke.

(Ship. Wt. 5 lbs.)

Cat. No. 2828-6HL

——————————

2000 Series Lanyards B-Ian Shock Absorbers, 6’ Fixed Length
- 1” nylon web with B-Ian

R. 2000 Series Fall Arrest Lanyard with Two 1234 rope R.
snaphooks. (Ship. Wt. 2.5 lbs.)

Cat. No. 2004NWB-6

S. 2000 Series Fall Arrest Lanyard with One 1234 rope
snaphook and a loop end. (Ship. Wt. 2 lbs.)

Cat. No. 2005NWB-6 S.

T. 2000 Series Fall Arrest Lanyard with Two 1234 rope
snaphooks. (Ship. Wt. 2 lbs.)

Cat. No. 2006NWB-6 T.

[email protected] Call Toll Free (800) 438-6013

FALL PROTECTION & RESCUE

N8 Lanyard & Anchorage Tips

FALL PROTECTION 1. Lanyard & Anchorage Tips
& RESCUE 2.
Tips For Use, Inspection, Care, and Maintenance of Lanyard,
2. 4. Anchorages
3.
6. • Read, understand, and follow all the instructions included with or affixed
5. 9. to the lanyards and anchorages prior to use. Do not use this equipment
8. 10. without proper training. (1)
7.
• Never punch holes in woven nylon material.

• Verify that the connector on the end of the lanyard is proper for
attachment to the harness or anchorage.(2)

• The average useful life of Bashlin anchorages and lanyards made of
synthetic material is 2 years from the service date or 3 years from the
date of manufacture, whichever comes first.

Lanyards
• Do not lay or drag lanyards on the ground. This is a proven method of

exposing the product to mechanical or chemical damage.

• Never connect 2 lanyards together to make a longer lanyard. (3)

• Carry an attached lanyard either on the shoulder, or in some other
manner that will keep it out of the way, and not be a tripping hazard when
walking or climbing.

• Never put knots in rope or webbing lanyards as this will decrease the
strength by as much as 30%. However, looping lanyards and harnesses
is an approved method of lanyard attachment as long as it is done per
Bashlin instructions. (4)

• Never connect a lanyard snaphook into web loop, directly onto a
horizontal lifeline, or around an anchor and back onto itself. (5)

• Never attach more than one lanyard to a “D” or “O” ring.

• If a lanyard is to be connected directly to a web loop, use a locking
carabiner designed for that purpose. (6)

Anchorages
• Select an anchor point that provides adequate strength per OSHA

requirements and will limit the pendulum motion and free fall distance.
The ideal point is directly overhead and positioned to limit the free fall to
2 feet or less.

• The location of the anchorage must not allow contact by the worker to a
lower level, or the ground during an arrested fall.

• Do not use nylon web anchor slings around structures with sharp edges
unless provisions are made to keep the edge from cutting the sling. (7)

Inspecting Lanyards and Anchorages
These products must be inspected prior to every use. Remove them from
service if you notice any of the following:

1. Safety hardware which has electrical burns, cracks, or deformities.
Snaphooks must operate easily and smoothly. They close
completely and lock. (8)

2. Strength members which are worn, cut, abraded, or have suffered
chemical degradation. (9)

3. Sewing or splices which are torn, cut, or have broken stitches. (10)

Care of Lanyards, Nylon Anchorages
Cleaning - Any cleaning is done with mild soap and water. We
suggest placing the lanyard in a mesh bag (Bashlin #10HBM), then, in a
clothes washer on the gentle cycle, or you may simply hand wash with
soap and water. Never use petroleum-based cleaners, as they will degrade
the nylon. Dry the lanyard by hanging, but do not place in a clothes dryer.

Storage - Store in a pouch or compartment away from the sun. Do not
store close to heat, as it will dry the nylon and degrade the material.

www.americansafety.com 24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE N9

Lifeline Kits & Accessories

700 Series Rescue Kit - Designed for use in aerial lift devices. FALL PROTECTION
The 700FP attaches semi-permanently to the boom with a & RESCUE
ratcheting boom strap, while the 700FWI is stored in a canister
mounted directly on the truck body. Both of the units feature
aluminum blocks with nylon sheaves and 75’ of twisted rope.
Other rope lengths are available on request. A carabiner is
provided for attachment to the victim.

NOTE: Proper training is required to use these items.

Cat. No. Description Ship. Wt. A.
A. 700FP Boom Mount Rescue Pack 8 lbs.
B. 700FWI
Truck Mount Rescue Kit 14 lbs.

—————————— D.
E.
C. Basic Temporary Horizontal Lifeline Kit - Contains all the
necessary equipment to act as a “floating” anchorage. This allows
a worker to travel horizontal for long distances without the risk

B.of pendulum or swing falls. This kit contains the 60’ (18 m) long,

5/8” (16 mm) thick FPS60KH/16ST polyester static kernmantel
rope with one swagged eye. This rope has high strength and
low stretch. The kit also contains the FPS3521 rope tensioner,
two FPS85 carabiners, two FPS02/6 anchorage slings, the 4’
FPS22322 lanyard with shock absorber and the FPS1010 bag.
The rope has a breaking point of 15,000 lbs. (70kN) and the
lifeline can adjust to lengths up to 60’ (20m).(Ship. Wt. 45 lbs.)

Cat. No. FP1001

——————————

Bashlin Boom Straps are made of 10,000 lb. test nylon F.
web and have nylon pads to protect the fiberglass boom.

The hardware is plated for corrosion resistance. The

standard length is 55”.

Cat. No. Description Ship. Wt.
D. 703-BS Boom Strap Only 1.25 lbs.
E. 703R Ratcheting Boom Strap
4.5 lbs.
(only for tapered booms)
F. 703R-2D 2 D-Ring Boom Straps 4.5 lbs.

for over center lifts

——————————

G. Large Horizontal Lifeline Kit Bag - C.
Made of orange cordura.

Size: 24” W x 11” D x 14” H

Ship. Wt. 3 lbs.

Cat. No. 60-906 G.

[email protected] Call Toll Free (800) 438-6013

N10 FALL PROTECTION & RESCUE

Rescue & Safety Lines

A. Gotcha Rescue Kit - Designed for tradesmen who work at
height.

FALL PROTECTION The Gotcha rescue kit is a unique solution to a problem faced
& RESCUE by all workers at height who use PPE for protection against falls.
Most rescue provision has focused on the more extreme activities
carried out at height, the Gotcha kit is designed for tradesmen
who use common items of fall protection. In the event of a fall
their situation (if suspended in a harness) is just as serious as any
other worker and a swift recovery is essential.

No knives are required when using this kit!

FEATURES:

A. • Suitable for Rescue from - Fall Arrest Lanyards and Fall Arrest Blocks
• This is no-cut kit - The casualty is raised to release their
original attachment.
• Rescue direction - You can raise or lower the casualty with this kit.
• Pre-assembled - No assembly is required by the user.
• Remote attachment - The casualty can be attached for a point of safety.
• Single person use - The Gotcha is for raising or lowering a single person.
• Maximum Working Length - The Gotcha Kit is available in three lengths.
• Color Coding - The kit is color coded for simplicity.

Cat. No. Rescue Distance Anchor Mode Ship. Wt.

GOTCHA50 High Anchor Low Anchor 15 lbs.
GOTCHA100 24 lbs.
GOTCHA150 Up to 55’ Up to 40’ 33 lbs.

Up to 110’ Up to 85’

Up to 165’ Up to 125’

——————————

B. Horizontal Safety Line - This Horizontal life line is easily
installed and tensioned using the built in ratchet system. For
Fall Restraint purposes the horizontal safety line can be used in
conjunction with the fixed length or adjustable restraint and fall
arrest lanyards. It can also be used as an anchorage.

HORIZONTAL SAFETY LINE:
For compatibility of use with fall arrest lanyards contact American
Safety Customer Service.

Tested for two person use, but please be advised that this type of
system should be for use by one person only.

The assembly is provided in a robust bag
with shoulder straps enabling the user to easily
carry it to the workplace.

B. FEATURES:
• Webbing loops at each end for attachment.
www.americansafety.com • Built in Wear Indicator.
• Tension force indicator.
• For two people.
• Individually serial numbered for traceability.
• ANSI A10.32-2004
• EN 795:1996 Class C

Cat. No. USHSL-LL


24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE N11

Rescue Accessories

C. Bozun’s Chair for Confined Space - Suitable for locations FALL PROTECTION
where space is restricted. It provides a stable seated position for & RESCUE

the user.

Can be used with the material winch for raising and lowering
personnel.

Can also be used with the spreader bar to allow comfortable
spacing of the attachments.

FEATURES: C.
• Allows operator to remain seated while being lowered or raised.
• Allows user to work hands free in confined space.
• Keeps user in vertical seated position.

Cat. No. USBC D.

——————————

D. Rope Rider Descender - A self locking descender rated
for loads up to 660 lbs. specially designed for those users who

require a high level of safety and security.

Meets all NFPA, ANSI, and CALOSHA standards for devices of
this type.

FEATURES:
• Anti panic mechanism.
• Easy to use.
• Can be used for two person rescue.
• Descent rate can be pre-set.
• For use on 7/16 inch or 1/2 inch rope.

Cat. No. USRR

——————————

E. Anchorage Connector - The WRAPPA is for single E.
person use as an anchor point onto vertical scaffold
poles (standards). It is for use with a shock-absorbing
lanyard and full body fall-arrest harness. It can be easily
positioned while in use and pre-positioned prior to the
tube being installed.

FEATURES:
• Provides a quantified anchor point on a standard scaffold tube.
• EWL 2 ft.
• Color coded to ensure correct installation and use.
• Continuous polyester sling surrounded with a protective tubular sleeve.
• MBS 70 kN.
• Supplied with clear user instructions.
• Individually serial numbered for traceability.

Cat. No. USWRAPPA

[email protected] Call Toll Free (800) 438-6013

FALL PROTECTION & RESCUE

N12 Rescue Kits

FALL PROTECTION A. A. The 700SRK Aerial Lift - Self Rescue is designed for personal
& RESCUE B. evacuation from an aerial lift that is broken. It also gives a worker
hanging off a platform or basket after an arrest fall, a means of
self-rescue. This is especially a concern for single-man crews.
It consists of an Evac-Pac, 50’ of rope and a web cutter, all in a
case carried on a waist belt.(Ship. Wt. 5 lbs.) NOTE: Proper training is
required to use this item.

Cat. No. 700SRK

——————————
B. The FE700SRKSC Aerial Lift-Self Rescue is designed for
personal evacuation from an aerial lift that is broken. It consists
of 50’ of polyester rope with an anchor eye spliced on one end, 2
carabiners, a DSD30 Descender and a carrying bag. It is also

available as a boom-mount device. NOTE: Proper training is
required to use this item.

Cat. No. Description Ship. Wt.
FE700SRKSC Aerial Self 5 lbs.

FE700BMSRSC Rescue Kit 5.5 lbs.
Boom Mount

Rescue Kit

C. ——————————
D. C. The Bashlin PARA-PAK is a self contained
rescue kit that mounts on the back of the Bashlin’s
683X style harness. This 2 pound low profile unit is
placed just below the back attachment point and
above the waist. It’s light weight and position is
designed so you never know it’s there, yet easy to
access when needed. The pack holds 50 feet of
rescue line, two carabiners and a descender. The carabiners are
color coded, so there is less chance of rigging the unit improperly.
The unit can be factory installed on any 683 style harness. Simply
add “SR” to the beginning of the part number. (Ship. Wt. 2 lbs.)

Cat. No. SR683XC

E. ——————————
F. The U-RES-Q Lanyard is a shock absorbing lanyard with a twist.
When the lanyard arrests a fall, as the shock absorber deploys, a
16-foot web ladder also deploys. The ladder is designed to provide
the worker a means for either self-rescue, or at the very least a
place to relieve the pressure on the body caused by hanging in the
harness for an extended period of time. This option is available on
lanyards made of 1” tubular or 1 3/4” nylon webbing.

Cat. No. Description Ship. Wt.
D. 2904-175-6 6 ft. 1 3/4” Lanyard 2.2 lbs.
D. 2904-175-4 4 ft. 1 3/4” Lanyard 2.1 lbs.
E. 2904-1-6 6 ft. 1” Tubular Lanyard 2.2 lbs.
E. 2904-1-4 4 ft. 1” Tubular Lanyard 2.2 lbs.

G. ——————————
The 711 Substation & Tower Rescue Kit series offers the user
multiple options for rescuing workers from substations, towers and
other elevated work areas. The units consist of 200 ft. of polyester
rope with eyes on the ends, 2 torso belts and the other equipment
shown. NOTE: Proper training is required to use these items.

Cat. No. Description Ship. Wt.
F. 711 Rescue Kit 12 lbs.
G. 711S Rescue Kit 15 lbs.

www.americansafety.com 24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE N13

Self-Retracting Lifelines

H. FallSafe Self-Retracting Lifelines - Nearly indestructible, the H. FALL PROTECTION
high impact-resistant nylon housing withstands the harsh rigors I. & RESCUE
of the toughest applications. The lightest, most rugged line of
composite retractables are designed with smooth, round edges to J.
increase durability.
• Corrosion-resistant stainless steel and aluminum internal components

extend service life and reduce replacement costs.

• Easy to handle and transport to/from job sites.

• Smooth, quiet operation; engineered spring retraction tension

designed not to pull or drag on a worker to improve productivity

and reduce fatigue.

• Load indicators identify when the unit needs to be removed from

service.

• No annual factory recertification required - lowers cost of ownership
and increases productivity. (Except in Canada where the Canadian

Standards Association requires annual factory recertification.)

• Rated to 400 lbs. capacity when using a SofStop shock absorber.

• Falcon web SRL rated for up to 400 lbs. worker.

Cat. No. Description
FS9925G 30’ stainless steel wire rope
FS9950G 50’ stainless steel wire rope

——————————

I. This 50 ft. Self-Retracting Lifeline has been designed with
safety and ergonomics in mind. Easy to handle and lightweight.
Twin inertia synchronized brake pawls and a constant triggering
speed, regardless of position, allow great work versatility. Built
with a fall indicating device snap hook connector and a braking
mechanism isolated from drum, and corrosion resistant anti-spark
parts. Allows hands-free positioning. Rubber wire end stop acts as
a handle. ABS casing with side handles. No annual recertification.
When subject to a fall, the unit must be returned for service. Meets
CSA Z259.2.2, ANSI Z359.1 standards and OSHA requirements
for fall protection. Includes carabiner. (Ship. Wt. 21.6 lbs.)

Cat. No. RT50G

——————————

J. Gotcha Constant Rate Descender - A constant rate descent
device for rescue and evacuation. It is also suitable for rescue

from - verticl situations where you can access the casualty.

Suitable for single person ot two person escape/evacuation from
elevated work areas.

FEATURES:
• Constant rate lowering and minimal user input are required
• The casualty can be raised to release their original attachment
• The casualty is lowered to safety
• Descent is set to a constant, controlled rate
• No assembly is required by the user
• The rescuer can access the casualty for recovery
• A single person can descend to safety
• The CRD can be used for successive evacuations “one after the other”

Cat. No. Rescue Distance
USGOTCHACRD50M Up to 160 feet
USGOTCHACRD100M
Up 10 325 feet

[email protected] Call Toll Free (800) 438-6013

N14 FALL PROTECTION & RESCUE

Lifehook® Fall Protection Systems

FALL PROTECTION A. The L-Series Lifehook® anchor is a key component of a
& RESCUE personal fall arrest system for training unqualified pole climbing
apprentices. These devices are pole-top mounted anchors that
have a 360° rotating davit. Full circumference mobility provides
complete fall protection to the climber as they move up, down, and
completely around the utility pole.

A. The lightweight L55 davit rotates quickly and predictably to remain
B. aligned above the climber to prevent a dangerous swing fall.
The SRL attachment point on the L55 is offset several additional
inches over competing products. This assures the line remains
behind the climber’s center of gravity and safely distances their
body from impact with the pole. The open, low-profile davit design
is also less susceptible to prevailing winds.

The installation bracket of the L55 has been designed to reinforce
the upper section of the utility pole. Under repeat fall arrest force,
Lifehook® products will not require ongoing adjustments to remain
level. There are two standard bracket sizes to choose from, and
custom size brackets are available by special order.

Tested Minimum Strength: 5,500 lbs.
Mounting Location: Top of Pole

Davit Range: 360°

Cat. No. Finish Bracket Size
L558G Hot Dip Galvanized 6” - 9”
L558P Painted 6” - 9”
L5510G Hot Dip Galvanized
L5510P Painted 8.5” - 10.5”
8.5” - 10.5”

——————————

B. The Lifehook® FB-Series anchor is a key component of a
personal fall arrest system for training unqualified pole climbing
apprentices. The heavy-duty FB6 is the second generation of
our original patented design. The Lifehook® FB6 features a 250°
rotating davit to provide compliant fall protection to the climber as
they move up, down, or around a 2/3 range of pole.
This anchor is unique in that it can be easily installed at any height
on a utility pole with a span between six and nine inches. The
main mounting bracket features a provision to prevent the bracket
from shifting side to side on the pole when under load. The
main bracket and davit of the anchor are furnished permanently
assembled for safety and strength.

The FB6 davit rotates rapidly, smoothly and predictably with
rated bearings on a solid axle of high tensile steel. Specific high
grade materials used in the construction of the FB6 assures
longevity and durability to rival competing products. The main
safety advantage of our design provides Lifehook® products with
a better ability to follow and remain above the climber to prevent a
dangerous swing fall.

The FB6 can also be used in tandem with another Lifehook®
system for applications where two climbers (instructor and trainee)
must be on the same pole. This is a safer alternative to competing
two-man systems whose climbers must share the same axis of
rotation where the movement of one climber can negatively affect
the other climber. Using Lifehook® systems in tandem
succeeds at meeting minimum strength requirements for
two attached workers while providing each climber with
an independently rotating davit.

Tested Minimum Strength: 5,500 lbs.
Mounting Location: Side of Pole, Any Height

Davit Range: 250°

Bracket Size: 6” - 9”

Protective Finish: Standard Paint, Royal Blue

Warranty: 2 years

Cat. No. FB6

www.americansafety.com 24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE

N15Manhole Guard with Material Lift & Accessories

C. Manhole Guard and Material Lift - Together, these products C. FALL PROTECTION
combine to create a very efficient work area safety device. The & RESCUE
manhole guard acts as a physical barrier around a manhole and
the material lift can lower and raise up to 300 pounds of equipment
in and out of a manhole. The entire system can be set up by one
man and is very portable. The guard is available in both 33” and
42” sizes. The winch combines independent ratchet systems for
additional load security and double disk brakes for positive load
control. This rugged material lift is an excellent device for raising
and lowering equipment and material into manholes. It clamps
securely to the universal manhole guard, making it a safety fence
as well as a valuable tool and rescue device. The entire unit is
lightweight and portable, sets up quickly and has a 300 pound
capacity with a safety factor of three to one. The side pieces are
constructed of high tensile, heavy-gauge aluminum with a durable
yellow finish that stands up to rough weather and wear. Lift rope
1/2” x 35’ DURA-PLEX Braided Rope.

FEATURES: Gear covers; bronze bushings; 2 independent ratchet
systems for additional load security; double-disk automatic brake
for positive load control; large handle roller, grips better in your
hand, winch bar of heavy wall, high tensile steel tubing with a 3”
drum for fast recovery.

Instructions for Mounting Material Lift: Place 2 mounting stanchions
on sides of manhole guard. Take 4 U-Bolts (furnished with unit) and
attach to sides of manhole guard. Placing stanchion with angle iron
to the right side, place winch into hole on left side and drop winch
into place, attaching the 2 lock pins in holes provided.
The lift may be ordered separately, or as a complete unit with
universal manhole guard.

33” Guards Description Dimensions Ship. Wt.
Cat. No. 39 lbs.
WAML-1DX Material Lift Only 3” Drum 12.5” x 13” x 41.5”
WAMGL-2DX D.77 lbs.
WAMG-2 Material Lift with Guard 33” x 6” x 52”
38 lbs.
Material Guard Only 33” x 3” x 42.5”

42” Guards Description Dimensions Ship. Wt.
Cat. No. 43 lbs.
WAML-42DX Material Lift Only 3” Drum 12.5” x 3” x 42.5” 87 lbs.
WAMGL-42DX 44 lbs.
WAMG-42 Material Lift with Guard 43.5” x 6” x 57.5”

Material Guard Only 43.5” x 3” x 42.5”

——————————

D. The Leg Extensions/Levellers extend and/or level a Manhole E.
Material Lift. They are made from high quality steel, and are
painted safety yellow.
Cat. No. Description Ship. Wt.
640-LE8 4 - 8”; Each leg is 8 1/4” with 6 lbs.
a movable steel pin that Operating Instructions:
allows 6” extension 1. Secure the “J” hook
640-LE12 4 - 12”; Each leg is 12 1/4” with 7 lbs.
a movable steel pin that through the hole of the
allows 10” extension manhole cover.
—————————— 2. Next, position shaft
over manhole(as
E. The “On Top” Easy Off Manhole Cover Remover is a shown); take up the
lightweight yet durable tool, versatile enough to remove even the chain slack and attach
most stubborn manhole covers. Constructed of extra-heavy walled to “S” hook.
steel tubing, it is reinforced at the stress point by an extra wide, 3. Pull back on Easy
extruded collar which provides 360° contact with the shaft. The Off handle displacing
chain is made of high strength steel; and our “J” hook is fabricated cover. Move tool
from plated alloy steel, hardened to provide dependable and away from manhole
consistent service. (Ship. Wt. 7.5 lbs.) until chain is tight
and repeat.

Cat. No. 660-CR
——————————

F. Manhole Cover Hook - Tool is designed to remove stubborn F.
manhole covers manually. Just insert the hook under the groove
of the lid and pull upwards. The hook is made from high-grade
hexagon tool steel properly hardened to prevent bending under
stress. (Ship. Wt. 5 lbs.)
Cat. No. 650-CH

[email protected] Call Toll Free (800) 438-6013

FALL PROTECTION & RESCUE

N16 Confined Space Rescue Equipment

FALL PROTECTION A. Aluminum Tripod - The lightweight and portable DBI-
& RESCUE SALA aluminum tripod is ideal for manhole entry and retrieval
applications. It is easily set-up by one worker and can be
transported from one location to another. Attach one or two
mechanical devices and you’re ready to go!

A. • UL Classified aluminum tripod.
B. • Quick-mount bracket for attachment of mechanical device.
• Rated working load is 350 lbs for working support or rescue.
• Adjustable locking legs with safety chains.
• Rubber safety shoes containing spiked edges for uneven surfaces.
• Top pulley assembly for routing of lifeline and eyebolt anchor points.

Cat. No. Height Ship. Wt.
7’ 47 lbs.
8000000
9’ 56 lbs.
8000010

——————————

B. Salalift® II Winch - This man-rated work support and rescue
winch is lightweight and easy to use. It is manually operated by
simply rotating the handle to raise or lower personnel or materials.
Galvanized cable is standard, stainless, and rope available.

• Gear ratio is 6:1 with an average lifting speed of 12.75’/min.
• Quick-mount bracket for attachment to tripod and safety hook

with impact indicator.
• Free-wheel mode for operator maneuverability and overload clutch

for added safety.
• Polyethylene housing for reduced weight and superior

corrosion resistance.

Cat. No. Length Lifeline Type
8102001
8102009 60’ 1/4” Galvanized Cable
8102005
8102050 90’ 3/16” Galvanized Cable

120’ 3/16” Galvanized Cable

50’ 1/4” Spectra™ Synthetic Rope

——————————

C. 3-Way Sealed Self Retracting Lifeline (Opposite Page)
- This man-rated personal fall arrest component incorporates
a retrieval winch suitable for raising and lowering personnel in
emergency rescue/retrieval situations. In the event of a fall, the
brake will stop the fall and limit arresting forces to
900 lbs. or less.
• Quick-mount bracket for attachment to tripod and carrying bag.
• Sealed design for the ultimate in durability and corrosion resistance.
• Aluminum and stainless steel construction for added
corrosion resistance.
• Safety hook with impact indicator.

Cat. No. Sealed? Length Lifeline Type Ship. Wt.
3400107 Yes 30’ 1/4” Spectra™ Rope 36 lbs.
3400307 Yes 55’ 1/4” Spectra™ Rope 52 lbs.
3400115 Yes 50’ 3/16” Galvanized Cable 41 lbs.
3400311 Yes 85’ 3/16” Galvanized Cable 59 lbs.
3400509 Yes 130’ 3/16” Galvanized Cable 83 lbs
3400620 No 175’ 3/16” Galvanized Cable 115 lbs.

www.americansafety.com 24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE

N17Rescue Tripod

D. Tripod & Salalift® II Rescue System - This DBI-SALA system FALL PROTECTION
is ideal for typical manholes and combines our lightweight and & RESCUE
portable aluminum tripod with the SALALIFT®II Winch. The
system is easily set-up by one worker and can be transported from
one location to another.

• Complete confined space entry/retrieval system.
• Includes tripod, winch, and/or self retracting lifeline.
• All systems are man-rated.
• All mounting hardware and brackets are included.
• Tripod size: 7’

Cat. No. Winch SRL Ship. Wt. C.
8300030 60’ N/A 83 lbs.
8300034 84 lbs. D.
8301000 1/4” Galvanized Cable N/A 94 lbs.
8304010 120’ 133 lbs.
50’
3/16” Galvanized Cable 3/16” Galvanized Cable
N/A
50’
60’ 3/16” Galvanized Cable
1/4” Galvanized Cable

——————————

E. The Pelsue Rescue Tripod is designed for industrial rescue
applications. Telescoping anodized-aluminum legs allow for height
adjustments in 5” increments per leg. The legs also adjust to any
angle to meet the most demanding situations! Cast-aluminum
head has three heavy duty rigging anchor points plus a built-in,
man rated, cable ready pulley. Our rescue tripod adjusts to 11’ 6”
allowing for full retrieval of a litter basket in vertical rescues.

FEATURES:
• Three rigging anchor points proof rated to 5,000 lbs. at fully

extended height.
• Built-in cable ready pulley.
• No load supporting welds.
• Adjustable telescoping legs - 5” increments.
• Feet convert to soft ground anchors and are pre drilled for anchor

bolts or stakes.
• Base chain included to maintain stability.

Pelsue Rescue Tripod Model P054 with Built in Cable Pulley -
Minimum Height: 6’

Maximum Height: 11’ 6” E.

Heavy Duty Carry Case: P057
Ship. Wt. 62 lbs.

Cat. No. P054

Pelsue Rescue Tripod Model RT07 with Built in Cable Pulley -
Minimum Height: 4’

Maximum Height: 7’

Heavy Duty Carry Case: P058
Ship. Wt. 57 lbs.

Cat. No. RT07

Winch with Stainless Steel Cable & Bracket for P054 and
TR07 Tripod -

Cat. No. Size
TW07C 70’ x 3/16”
TW10C 100’ x 3/16”

[email protected] Call Toll Free (800) 438-6013

FALL PROTECTION & RESCUE

N18 Pelsue Axial Ventilators

A. Axial Ventilators - Models 1320 & 1420 -

FALL PROTECTION A. Cat. No. 1320 1420
& RESCUE
Power Electric - 1/6 HP 120 VAC, Electric - 1/4 HP 12 VDC,
1.4 Amps 15 Amps

Certifications CSA, CEESI CEESI

Dimensions 12” L x 8.5” W x 12.5” H 12” L x 21.5” W x 31.7” H

Free Air (certified) 809 cfm 719 cfm

w/ one 90° bend 617 cfm 502 cfm

w/ two 90° bends 505 cfm 425 cfm

Ship. Wt. 15 lbs. 17 lbs.

B. Axial Ventilators - Models 1325D & 1400D -

Cat. No. 1325D 1400D
B. Power
Electric - 1/3 HP 120 VAC, Electric - 1/4 HP 12 VDC,
3 Amps 15 Amps

Certifications CSA, CEESI CEESI

Dimensions 14.5” L x 13” W x 14.5” H 14.5” L x 13” W x 14.5” H

Free Air (certified) 1075 cfm 922 cfm

w/ one 90° bend 558 cfm 541 cfm

w/ two 90° bends 585 cfm 518 cfm

Static Pressure 2.09” H2O 1.46” H2O
Ship. Wt. 20 lbs. 20 lbs.

C. Axial Ventilators - Models 1325P & 1400P -

Cat. No. 1325P 1400P

C. Power Electric - 1/3 HP 120 VAC, Electric - 1/4 HP 12 VDC,
3 Amps 15 Amps

Certifications CSA, CEESI CEESI

Dimensions 18” L x 14” W x 15” H 18” L x 14” W x 15” H

Free Air (certified) 921 cfm 814 cfm

w/ one 90° bend 575 cfm 478 cfm

w/ two 90° bends 546 cfm 479 cfm

Static Pressure 1.87 H2O 1.2 H2O
Ship. Wt. 15 lbs. 15 lbs.

www.americansafety.com 24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE N19

Pelsue Axial Ventilators

D. Axial Ventilators - Models 1375D, 1385D, 1475D & 1485D -

Cat. No. 1375D & 1385D 1475D & 1485D FALL PROTECTION
Power Electric - 1/3 HP 120 VAC, Electric - 1/4 HP 12 VDC, & RESCUE
3 Amps 15 Amps
Certifications CSA, CEESI CEESI
Dimensions 37” L x 13” W x 14.5” H 37” L x 13” W x 14.5” H
w/ one 90° bend 668 cfm/558 cfm 541 cfm/492 cfm
w/ two 90° bends 585 cfm/553 cfm 518 cfm/490 cfm
Ship. Wt. 40 lbs. 40 lbs.

D.

E. Axial Ventilators - Models 1375P, 1385P, 1475P & 1485P -

Cat. No. 1375P/1385P 1475P/1485P
Power Electric - 1/3 HP 120 VAC, Electric - 1/4 HP 12 VDC,
3 Amps 15 Amps
Certifications CSA, CEESI CEESI
Dimensions 36” L x 14” W x 15” H 36” L x 14” W x 15” H
w/ one 90° bend 575 cfm/540 cfm 478 cfm/439 cfm
w/ two 90° bends 546 cfm/544 cfm 479 cfm/433 cfm
Ship. Wt. 36 lbs. 36 lbs.

E.

[email protected] Call Toll Free (800) 438-6013

FALL PROTECTION & RESCUE

N20 Pelsue Ventilation Accessories

FALL PROTECTION A. “AirPac” Series Hose & Canister - The AirPac series is
& RESCUE a molded polyethylene canister and hose combination, which

A. attaches to the 1325P and 1400P ventilators. The AirPac 15
includes a 15 ft. hose. The Airpac25 includes a 25 ft. hose.

NOTE: Available in a combination unit as models 1375P, 1385P,
1475P, 1485P.

Cat. No. AIRPAC

——————————

B. 2000 Series Ventilator Hoses - Three styles of high quality 8”
ventilation hoses. Hoses have cuff and strap at one end.

B. Cat. No. Description Length
C. 2015HRT Standard Wt. 15’
2025HRT Standard Wt. 25’
2015HD Heavy Duty Wt. 15’
2025HD Heavy Duty Wt. 25’
2006-N Insulated 6’
2015-N Insulated 15’
2025-N Insulated 25’

——————————

C. “SpaceMaker” Series Ventilator Hoses - Our SpaceMaker
hose allow unrestricted, continuous ventilation during entry and
egress of a confined space. There are no accessory parts. Stores
in a regular hose canister. Hose is 8” diameter x 15 ft. long.
NOTE: Not for use with heated air above 250°.

Cat. No. SPACEMAKER15

——————————

D. D. “Pel Can” Hose Storage - Steel construction, and coated with
a weather resistant, safety yellow powder coat finish.

Cat. No. Description
3025A Holds all HRT & 2015HD hoses
3035A
Holds all HRT & 2035HD hoses

E. ——————————

E. Hose Storage - Constructed of a
durable, weather resistant, high impact

polyethylene plastic, and will hold HRT

model hoses only.

Cat. No. 3015P

www.americansafety.com 24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE N21

Pelsue Ventilation Accessories

F. FlexPac15 is an 8” hose and carrier all in one. Attaches FALL PROTECTION
securely to 8” heaters and blowers. Stores & RESCUE

quickly and easily.

Cat. No. FLEXPAC15

——————————

F.

G. Suction Adapter - Our Model 3003P suction adapter attaches
to the intake side of the 1325 & 1400 series ventilators, so that

you may attach an 8” diameter hose to provide suction.

Cat. No. 3003P

G.

——————————

H. Hose To Hose Connector - Our aluminum hose to hose
adapter is easily installed to securely combine lengths of 8”

diameter ventilator hose.

Cat. No. 2101

—————————— H.

I. “Flo-Check” Air Flow Monitor - The Pelsue Model “FLO- I.
CHECK” is a completely portable and cordless air flow monitoring
and alarm system. Such a system is invaluable in the safe entry of
a properly ventilated confined space. The unit is battery powered
via internal, rechargeable batteries and its sensor probe can be
secured to any variety of ventilation duct or hose. When “powered
on” the internal circuitry of the device will sense a drop in air
flow and will respond by emitting an audible and visual warning
alarm. Onboard LED lighting and a compact speaker unit provide
the warnings. A charging jack is built into the FLO-CHECK’s
enclosure, and a charging unit is included which will charge the
batteries from any standard 120V AC wall receptacle in under 8
hours. A fully-charged unit will operate in “alarm-mode” for over 5
days continuously. A 15’ long sensor hose is included, enabling the
placement of the enclosure and alarm up to 15’ away from location
of the probe. The enclosure is equipped with a hook and loop
strap allowing it to be secured in a suitable location.

Cat. No. FLO-CHECK0

[email protected] Call Toll Free (800) 438-6013

FALL PROTECTION & RESCUE

N22 Pop ‘N’ Work Ground Tents

FALL PROTECTION Unique Features: Fast & Easy
& RESCUE
Quick & Simple Setup: 1. Lift Door and Step Inside
• Just pop out two tension frames.
• No loose parts.

Sturdy Construction: 2. Pop-Out one tension frame.
• Cold - rolled, steel hinges.
• Heavy duty fiberglass tension rods.
• All tension rods glued and bolted

WILL NOT PULL OUT.
• Roof supports heavy loads.
• Tough zipper door closures.
• Extra heavy duty cover.

Stands up to Strong Winds:
• Tent Structure is tight and rigid.

• Takeup straps for extra tightening.

Many Sizes & Designs: 3. Pop-Out 2nd tension frame.
• 4’ x 4’ to 12’ x 12’.
One Person Can Set Up A • Square and rectangular shapes.
POP-N-WORK Shelter In Less • Rollup & pole wrap doors.
• Connecting tents. Wall Tents.
Than 30 Seconds. • Custom designs.
No Loose Parts To Lose Or
For All Sizes & Models:
Slow You Down. • Plenty of headroom.
• Blower ports & windows.
All POP-N-WORK Shelters • Road - visible safety strips.
Have A Quick-Pak-Flap To • Both one door and two door tents.
Carry and Store The Shelter
www.americansafety.com No Color Distortion:
• White & gray cover.

• More efficient splicing.

Quick - Pac - Flap:
• For easy store and carry.

3 Factors Have Guided Design Efforts:

BETTER WIND STABILITY:
Heavier fiberglass rods - Stronger tent.
No roof hinge to collapse - Once roof hinge collapses tent falls.
Tension straps - For extra stability in high winds.

USABILITY FACTORS:
Two tension mechanisms - Easier setup.
Double thick cover fabric - Longer lasting.
Two door, connecting and pole wrap style door designs - Options.
Rectangular shapes - Allow easier placement.
Blower ports on all versions - There when you need it.
More head room - More comfortable to use.
Roof strut can support hanging lights - Options.
White and gray fabric color - Doesn’t distort color in tent.
Quick-pac flap for storage - Unlike a bag it doesn’t get lost.

LONGER LIFE - LOWER LIFETIME COST:
Unitized frame - No rods to poke through fabric.
Heavier fabric - Lasts longer.
Hinges are cold rolled steel rather than cast - Doesn’t break.
Heavier fiberglass rods - Stronger tent.
Glued and pinned rods - Rods don’t pull out.
Heavy duty zippers - Better than plastic clips or cheap zippers.
Easily replaced cover - Reuse frame - Saves money!

THE POP ‘N’ WORK PRODUCT LINE INCLUDES...
Aerial Shelters, Aerial Covers, Van/Ground Shelters, Splicing Shelters,
Manhole Shelters, Ground Transmission Shelters, Umbrellas, Splash
Curtains for Manhole Gate Guards, Covers with Pop-Up Frames for
Manhole Gate Guards, Pedestal Protection Bags.

24 hour Fax (704) 481-0450

FALL PROTECTION & RESCUE

N23Work Tents & Umbrellas

Frame GS/FX Features and Options for Ground Strut (GS) and Flex Tent (FX)
Exclusive POP ‘N’ WORK unified frame. Stands independent of the cover. Two side walls pop out for quick setup. Cold
GS rolled steel hinges are unbreakable with all joints and hinges bolted, the frame cannot pull apart unexpectedly. Cover at- FALL PROTECTION
tachments designed for easy cover replacement. & RESCUE
FX The GROUND STRUT is a steel tube along the bottom of the rear wall. The cover is attached to the strut to give the tent
free-standing stability. The strut has a slight bow to let the tent set firmly on uneven terrain. Tents with two roll-up doors
Cover GS/FX have straight Ground Struts in both front and rear.
Doors GS Instead of Ground Struts, the FX TENT has an X-Frame in the rear wall. It telescopes automatically when the side frames
are popped out. The X-frame gives the tent free-standing stability and extra special support important to large tents. The FX
FX TENT also has the flexibility for squeezing into tight spots and adapting to rough terrain. FX TENTS are 6’ x 6’ and larger.
Urethane coated polyester fabric. Frame retardant to meet CPAI-84. Standard color white with lower side walls gray, orange
Windows GS/FX safety stripe on each side. Other colors are available.
Vent Port GS/FX A GROUND STRUT TENT can have one or two doors. 5 door design options: Slit door with zipper, 4’ wide roll-up door with
zippers. 4 wide roll-up door with hook and loop closures, connecting door with zipper (join two or more tents), connecting
Floors GS/FX door with pole wrap closure (for work adjacent to poles).
A FLEX TENT can have ONE DOOR. 4 door design options: slit door with zipper, 4’ wide roll-up door with zippers, connect-
Windlines GS/FX ing door with zipper (joins two tents), connecting door with pole wrap closure (for work adjacent to poles).
Netted window in rear wall (9” x 36”). Additional windows and vinyl windows are optional.
Carrying Bag GS/FX A 10” diameter Vent Port with draw cord closure is standard on all tents. It is located in the rear wall and is compatible with
standard blower and heater hose.
Van Tent GS FIBER OPTIC SPLICING TENTS have a polyester floor with hook and loop along all four edges. Hook and loop along the
bottom edge on all four sides. Floors with corner ties are available for all tents.
Safety Vent GS/FX For windy conditions, tents that are 6’ x 6’ and smaller have 1/4” ropes attached to the center of two sidewalls. Larger tents
also have 1/4” ropes attached to each corner of the tent at the roof.
All tents have a large ground flap along the rear wall that is used to carry and store the tent. It has snap hooks and handles.
Just roll the tent into the flap and snap the hooks. This wrap is called the QUICK-PACK.
The VAN TENT is designed to be set on the van bumper and attached to the van. It has roll-up doors both front and rear
with zipper closures. Standard sizes are 6’ x 6’ and 8’ x 8’. The VAN TENT can be used as a ground tent.
The SVT/TENT has two 18” x 24” openings at ground level. Openings have flaps with hook and loop closures. The standard
netted window and a top opening door zipper provide additional cross ventilation. Designed for manhole use.

Standard Sizes for Ground Strut (GS) and Flex Tents (FX)

GS GS or FX SERIES
SERIES
GS or FX SERIES
ONLY
OPTIONAL 2nd DOOR
GS SERIES (GS SERIES ONLY)
ONLY

GS or FX SERIES

Work Umbrellas

GS or FX SERIES Cat. No. Size 2 Part Pole

Standard Circular Umbrella with Steel Ribs
6684W 66” dia. 84” - Hardwood
7884W 78” dia. 84” - Hardwood
GS or FX SERIES 7886M 78” dia. 86” - Aluminum(Tilt)

GS SERIES ONLY 8492W 84” dia. 92” - Hardwood
8492M 84” dia. 92” - Aluminum(Tilt)
GS SERIES COMBINATION
ONLY VAN/GROUND Dielectric Circular Umbrella with Fiberglass Ribs

COMBINATION 7886FW 78” dia. 84” - 2 pc. Hardwood
VAN/GROUND

8492FW 84” dia. 84” - 2 pc. Hardwood

Square Umbrella with Steel Ribs
5484MS 54” x 54” 84” - Aluminum(Tilt)

[email protected] Call Toll Free (800) 438-6013

FALL PROTECTION & RESCUE

N24 Karabiners, Maillon Connectors & Pulleys

FALL PROTECTION Our Karabiners Feature:
& RESCUE • Steel Construction
• 3,600 lb. gate
• ANSI Z359.1.-2007

A. A. Large Karabiner - The offset “D” shape maximizes the
B. karabiner’s strength by placing the load close to the back bar of
the karabiner. 1 inch gate opening for larger applications. This
C. karabiner comes complete with a captivating pin for application
where the karabiner needs to be held in place preventing cross
D. loading or loss.
F. Cat. No. USN2562

E. B. Karabiner - This is our most popularly used karabiner being
safe, strong and versatile. Incorporating a user fitted captive pin
G. this karabiner can be used on equipment and held in place to help
H. prevent accidental cross loading or loss. It has a 5/8” gate opening.
Cat. No. US2156
www.americansafety.com
C. Oval Karabiner - This oval connector is suitable for a number
of fall protection applications from general applications through
to rope access and rescue. The oval shape makes it particularly
useful with pulleys for hauling, etc. Has a screw gate closing.
Cat. No. USML2

——————————

Our Maillon’s Feature:
• Screw lock openings
• 9mm Steel
• Capable of sustaining multi-directional loads

D. Delta Maillon - The delta maillon is an ideal connection
hardware for permanent and temporary applications. Best suited
for the assembly of components to build working systems. They
are extremely durable and are designed for multidirectional loads.
Their size and shape make them both useful and popular for
personal fall protection systems, rigging and rope access.
Cat. No. USDZ09

E. Oval Maillon - The oval maillon is an ideal connection
hardware for permanent and temporary applications. Best suited
for the assembly of components to build working systems. They
are extremely durable and are designed for multidirectional loads.
The practical shape and versatility of this connector makes it the
most popular shape.
Cat. No. USNZ09

——————————

F. Single Wheel Swivel Cheek Pulley - Green single wheeled
swivel cheek pulley for rope access, rigging and rescue purposes.
With attachment eyes top and bottom. Swivel cheeks make loading
the rope easy. Holds rope diameters up to 13mm. (Ship. Wt. 3.2 oz.)
Cat. No. USPULS

——————————

G. Double Wheel Swivel Cheek Pulley - Dual wheeled swivel
cheek pulley for rope access, rigging and rescue purposes. With
attachment eye to the top. Swivel cheeks make loading the rope
easy. Holds rope diameters up to 13 mm. (Ship. Wt. 3.7 oz.)
Cat. No. USPULT

——————————

H. Fall Arrest Device for Use on Rope - Suitable for
vertical installation as fall arrest device or as a backup
for rope access work. Can be used with an
attachment lanyard up to a maximum length of
12”. Works on tensioned or weighted rope. Conforms
to ANSI Z359.1(07). Made for rope 11.5mm - 12.7mm.
Cat. No. USBUD

24 hour Fax (704) 481-0450