Microsoft Word - 1A QUANTICORP HOLDINGS PORTFOLIO PRODUCTS.docx

Vapor Blast Machine
Self-contained with trailer, engine and compressor
The Graco EQ400t vapor blast machine is designed for the toughest high production projects. The EQ400t is compact and easy to use and maneuver at any jobsite. Our self-contained blast machine is ideal for removing layers of tough industrial coatings and corrosion for a wide-range of applications:
• Industrial surface preparation • Restoration
• Marine maintenance
• Graffiti removal
• Blast cleaning
The features of our heavy duty vapor blast machines generate less dust and use less water, saving you time and money.
Quanticorp
Vapor Abrasive Blasting: A cleaner, easier path to profitable results
• Generates less dust – 92 percent less airborne dust than dry blasting
• Uses less water than traditional water-based wet blasting
• Optimizes air, water and media ratio – resulting in a fine mist with a blast that is powerful, • but with less dust
• Uses less media than wet blasting, so clean up is minimal* and you save on media costs Built to take a beating
• EcoQuip systems are built with heavy-duty stainless steel crash frames to withstand the • toughest conditions
• 5x safety rated frame
Designed for years of solid service
51


Quanticorp
SPECIALIEZED SAND BLASTING EQUIPMENT
DUSTLESS BLASTING
52


Vapor Abrasive Blast Equipment
For high production vapor blasting
Built to withstand the toughest working conditions, the EQ600s is Graco’s high-production standalone vapor blasting unit to tackle your largest, most demanding projects. Our heavy duty abrasive blast equipment is designed for years of service.
• Requires 375-600 cfm air compressor
• Fits inside a six foot truck bed for easy transport • Stacks easily to save space
Graco’s blasting equipment serves a wide-range of industries from professional cleaning,
Vapor Abrasive Blasting: A cleaner, easier path to profitable results
• Generates less dust - 92 percent less airborne dust than dry blasting
• Uses less water than traditional water-based wet blasting
• Optimizes air, water and media ratio – resulting in a fine mist with a blast • that is powerful, but with less dust
• Uses less media than wet blasting, so clean up is minimal* and you save • on media costs
Built to take a beating
• EcoQuip systems are built with heavy-duty stainless steel crash frames to • withstand the toughest conditions
• 5x safety rated frame
Designed for years of solid service
Quanticorp
53


Industrial Size Blasters
Quanticorp
CONTACT US FOR MFOR INFORMATION
54


Quanticorp
SPECIALIEZED SPRAY EQUIPMENT
INTERIOR PIPE COATING & SANDING EQUIPMENT
55


Quanticorp
SpinCoater, 2" ID pipe
Description
Ideal for 2" pipe. This SpinCoater does not come with a centering carriage.
THE Heavy Duty Spray Coaters are designed to apply internal coatings and linings to pipe. These tools have a pneumatic driven spray head that will spray most all coatings from the thinnest to the most viscous. The coating to be applied is fed to the spray head through a fluid manifold for maximum material disbursement.
The most popular setup is shown here. The Spincoater is attached directly to a paint tank with ball valves to control the fluid and air lines.
The SpinCoater can also be used with an airless setup. It is important to note the use of the back pressure orifice assembly.
56


Quanticorp
SpinCoater, 3"-5" ID pipe
Description
Ideal for 2"-5" pipe.
The Heavy Duty Spray Coaters are designed to apply internal coatings and linings to pipe. These tools have a pneumatic driven spray head that will spray most all coatings from the thinnest to the most viscous. The coating to be applied is fed to the spray head through a fluid manifold for maximum material disbursement.
Model HDCBX360-2 comes with centering carriage (PN: HBC01124) that fits in 3"-5" pipe.
The most popular setup is shown here. The Spincoater is attached directly to a paint tank with ball valves to control the fluid and air lines.
The SpinCoater can also be used with an airless setup. It is important to note the use of the back pressure orifice assembly.
57


Quanticorp
SpinCoater
Description
Ideal for 5"-12" pipe.
The Heavy Duty Spray Coaters are designed to apply internal coatings and linings to pipe. These tools have a pneumatic driven spray head that will spray most all coatings from the thinnest to the most viscous. The coating to be applied is fed to the spray head through a fluid manifold for maximum material disbursement. Model HDCBX360-3
The most popular setup is shown here. The Spincoater is attached directly to a paint tank with ball valves to control the fluid and air lines.
The SpinCoater can also be used with an airless setup. It is important to note the use of the back pressure orifice assembly.
58


Quanticorp
SpinCoater, 8"-18" ID pipe
Description
Ideal for 8"-17" pipe.
The Heavy Duty Spray Coaters are designed to apply internal coatings and linings to pipe. These tools have a pneumatic driven spray head that will spray most all coatings from the thinnest to the most viscous. The coating to be applied is fed to the spray head through a fluid manifold for maximum material disbursement. Model HDCBX360-4
The most popular setup is shown here. The Spincoater is attached directly to a paint tank with ball valves to control the fluid and air lines.
The SpinCoater can also be used with an airless setup. It is important to note the use of the back pressure orifice
59


Quanticorp
SpinCoater, 12"-36" ID pipe
Description
Ideal for 12"-36" pipe.
The Heavy Duty Spray Coaters are designed to apply internal coatings and linings to pipe. These tools have a pneumatic driven spray head that will spray most all coatings from the thinnest to the most viscous. The coating to be applied is fed to the spray head through a fluid manifold for maximum material disbursement. Model HDCBX360-6
The most popular setup is shown here. The Spincoater is attached directly to a paint tank with ball valves to control the fluid and air lines.
The SpinCoater can also be used with an airless setup. It is important to note the use of the back pressure orifice assembly.
60


Quanticorp
Hollo-Blast (tc tip) with 5/8" noz
Description
The Hollo-Blast Cleaning Tool is designed to blast clean small pipe ranging in size from 2" to 12" inner diameter.
Button carriage (PN: HBC01124) is for 3"-5" I.D. pipe. Adjustable scissor carriage (PN: HBC01131) is for 5"-12" pipe. Carriage not included with tool.
Internal pipe surface preparation is accomplished easier, faster and more economically by using high quality Pipe Cleaning Tools. These tools are designed to blast clean without the necessity of rotating the pipe. They remove rust, old paint and any other contaminant better than any other method. Through highly powered abrasive impact, precise surface profiles can be obtained which will ensure proper adhesion for long life coatings. Standard abrasive blast machines are used in conjunction with all Pipe Cleaning Tools. Pipe Cleaning Tools are constructed, in part, of high grade Tungsten Carbide and engineered to provide many hours of productive work. Various Tungsten Carbide nozzle sizes are available to comply with a wide range of pipe diameters. Any standard blasting abrasive may be used with the exception of Aluminum Oxide and Silicon Carbide. Maximum abrasive size for the Hollo Blast Tool is 20 mesh.
This tool, which has no moving parts, utilizes a built-in, short venturi, Tungsten Carbide nozzle and Tungsten Carbide deflection tip to spray accelerated abrasive in a 360° blast pattern. Tungsten Carbide deflection tip, stern sleeves, and stern support ensure long wear life.
This tool is supplied with a 1/2" orifice nozzle that is good for abrasives equal to or finer than 16 mesh. However, 5/8" orifice nozzle is also available, where sufficient air supply can be furnished, for courser abrasives. Air consumption is 200 CFM on 1/2" nozzle and 350 CFM on 5/8" nozzle.
Two centering devices are available. The tool without any centering device will fit into 2" I.D. pipe. With centering collars and buttons, the tool will adapt to pipe 3"-5" range at 1/2" increments. The larger centering carriage can handle all diameters between 5"-12" I.D.
The blast hose used with this tool should be no smaller than 1-1/4" I.D. Rotating the deflection tip a quarter turn after every 6 hours of use will maintain consistent wear throughout the life of the deflection tip.
61


Quanticorp
SpinBlast for 8" to 36" pipe
Description
The SpinBlast tool cleans the interior of pipes from 8" I.D. to 36" I.D. The tool connects to most abrasive blasting machines in place of a standard nozzle. As the tool passes through the length of the pipe being cleaned, abrasive is ejected by two special nozzles mounted on a rotating head.
Carriage is not included with the tool.
62


Quanticorp
SpinBlast HD, w/air-motor, for 18" to 48" pipe
Description
Ideal for I.D. pipe Greater than 14".
The SB-636-B Heavy Duty Spinblast Tool is designed to abrasive blast clean the internal diameter of pipe. This unit includes a pneumatic driven motor to rotate the blast head, and an adjustable carriage designed to center the tool in the pipe to produce a uniform blast cleaned surface.
Production Rate
This tool is shipped with two (2) 1-1/4" threaded venture blast nozzles. This unit with operates with nozzle sizes 1/4" to 5/8" I.D. The production rate varies depending on the degree of cleanliness required, surface condition, and type of abrasive, nozzle size and blasting pressure. Contact a Quanticorp Representative to determine an estimated production rate for your specific application.
Travel Rate
The speed (feet per minute) that this tool is pulled through a pipe depends on the diameter of pipe, degree of cleanliness required, surface condition, abrasive size, nozzle size and blasting pressure. A platform or structural support for the wheels of the Spinblast tool to drive on must be provided at the exit/entrance of the pipe to support the weight of the tool. Do not manually lift the tool out of the exit point of the pipe while blasting.
Blast Head Rotating Speed
A variable speed pneumatic or electric motor turns the blast head of the tool. The motor should be adjusted to 40-60 RPM to produce an even blasted surface. A 2-3 drops of 10 weight non- detergent lubricating oil should be added to the air inlet port on the pneumatic motor before and after each daily use.
Blast Hose Connection
The blast hose connection on the tool is 2" NPS-M. A standard 2" threaded blast hose fitting (CFB00555) is required if the Spinblast tool in not attached to a pipe lance. The blast hose of pipe lance feeding the tool must be a minimum of 1-1/4" I.D. Smaller diameter hose or pipe lances could lead to premature wear on the Spinblast tool.
Pneumatic Motor Connection
The pneumatic motor has a 1/8" NPT-F inlet and 1/8" NPT-F exhaust. The air line feeding the motor must be a minimum of 1/2" I.D. to provide an adequate volume of cleaned compressed air. An air regulator must be attached to this line to control the rotation speed of the blast head. The exhaust outlet on the motor must have a minimum 3/8" I.D. exhaust line to direct the exhaust air and air borne contaminants outside of the pipe and away from the blast cleaned surface
63


Quanticorp
SpinBlast HD-e w/electric motor and carriage
Description
Ideal for I.D. pipe Greater than 14".
The SB-636-B Heavy Duty Spinblast Tool is designed to abrasive blast cleans the internal diameter of pipe. This unit includes a pneumatic driven motor to rotate the blast head, and an adjustable carriage designed to center the tool in the pipe to produce a uniform blast cleaned surface.
Production Rate
This tool is shipped with two (2) 1-1/4" threaded venture blast nozzles. This unit with operates with nozzle sizes 1/4" to 5/8" I.D. The production rate varies depending on the degree of cleanliness required, surface condition, and type of abrasive, nozzle size and blasting pressure. Contact a Quanticorp Representative to determine an estimated production rate for your specific application.
Travel Rate
The speed (feet per minute) that this tool is pulled through a pipe depends on the diameter of pipe, degree of cleanliness required, surface condition, abrasive size, nozzle size and blasting pressure. A platform or structural support for the wheels of the Spinblast tool to drive on must be provided at the exit/entrance of the pipe to support the weight of the tool. Do not manually lift the tool out of the exit point of the pipe while blasting.
Blast Head Rotating Speed
A variable speed pneumatic or electric motor turns the blast head of the tool. The motor should be adjusted to 40-60 RPM to produce an even blasted surface. A 2-3 drops of 10 weight non-detergent lubricating oil should be added to the air inlet port on the pneumatic motor before and after each daily use.
Blast Hose Connection
The blast hose connection on the tool is 2" NPS-M. A standard 2" threaded blast hose fitting (CFB00555) is required if the Spinblast tool in not attached to a pipe lance. The blast hose of pipe lance feeding the tool must be a minimum of 1-1/4" I.D. Smaller diameter hose or pipe lances could lead to premature wear on the Spinblast tool.
Pneumatic Motor Connection
The pneumatic motor has a 1/8" NPT-F inlet and 1/8" NPT-F exhaust. The air line feeding the motor must be a minimum of 1/2" I.D. to provide an adequate volume of cleaned compressed air. An air regulator must be attached to this line to control the rotation speed of the blast head. The exhaust outlet on the motor must have a minimum 3/8" I.D. exhaust line to direct the exhaust air and air borne contaminants outside of the pipe and away from the blast cleaned surface.
64


Quanticorp
Quanticorp Holdings
Solution Provider
Super Polymer and Nano Coatings Ballistics for Defense
For the Military
Oil and Petroleum Sector Industry.
Contact a representative
Or our Exclusive Distributor in Mexico Corporativo SNS
Roma 325, Col. Mirador Monterrey N.L. México
52 81 82183160
65


Quanticorp
CONTACT INFORMATION
QUANTICORP HOLDINGS QUANTICORP US INFO@QUANTICORP .COM
66