Inland Waterways Brochure MARINEWARE.COM & &
2 Painting Hints and Tips Choosing the right System: Marineware supplies a range of systems aimed for both trade and DIY users. Many of the trade systems are not available to non-professionals due to current legislation. The increased cost of the two-pack solutions will pay you back with their longevity due to higher quality and better UV stability. However, applicator skill set and painting environment will play a significant role in the quality of the finish. Traditional single-packs are more tolerant to variable and less ideal conditions. If you’re painting in a marina or the side of the canal, we recommend the use of a single-pack system and picking the best of days to get the best results. Finally, a two-pack system will often react if it is applied over a single-pack product so, a single-pack system is a much safer option if you’re not sure about the type of paint you are going over. Steel Prep: Substrate preparation is the most important job to get right and is the main cause of paint failures. In a perfect world, we would blast and epoxy coat steel on the same day, however, this is not always possible. Selecting the right primer to go with the available preparation is also important, if there is any chance of rust having formed a surface tolerant primer should be selected. The trade painters normally head for the specialist surface tolerant epoxies whilst the boat owner would use a single-pack like Multi Marine Primer. This is a big subject but the biggest tip is always to download the data sheet and follow the instructions, or contact us for help. & &
3 When to Paint: The professionals tend to have better environments to paint in and therefore have more options available to them. If your vessel is steel, you need to consider the dew point before painting. This is the relationship between air temperature, surface temperature and relative humidity. If these three conditions are in the wrong order, condensation will form on the surface and stop the paints from adhering. Cleaning: The simplest of steps that are often not done properly. The first step is to clean everything before sanding or grinding. This stops the contaminants from getting ground into the scratch profile on the surface. Always use the suggested cleaner or degreaser, you can save a few pence on some cheaper ones but you will wish you didn’t if they fail. The trade applicators use the Two-Cloth method. This is simply applying the degreaser with one cloth and drying the surface off with a second clean cloth. Just wiping the surface with a degreaser only moves any contaminants around the surface and doesn’t remove them. Do not use on base blasted steel. Always paint 3°C above the dew point. (To help you, simply search the internet for a dew point calculator). Watch out for those warm days in early spring, when you have cold steel and high humidity! & &
4 Primers and Undercoats: The primer and undercoat you use will depend on the system and finish you choose. The most important tip here is don’t scrimp. Primers protect the steel from corrosion and they need some thickness to do their job. So, if you find you are sanding through your primer in lots of places then you need to apply more. Undercoats are less about protection and more about preparing a surface to get the best quality finish out of the topcoat. Topcoat Tips: When hand painting, use high-quality rollers and brushes and take your time. If the conditions, light or temperature is not right, then delay painting. Use the correct thinners as they are designed to work with the paint. Whatever the topcoat you are using, having the right film thickness on the boat will affect the longevity of the paint. Even if the paint covers really well in one coat, it will need multiple coats to give it the protection it’s designed to do. So always follow the datasheet. All the paint companies have a lot of experience and the data sheet is where they put all of that knowledge, even professional painters will still use data sheets to get the best results. Sanding Tips: Firstly, when branded abrasives are used we see better results with more even sanding. Start with all the hand sanding around details and fittings and then move on to using sanders, working back into your hand sanding areas. This will reduce the chance of seeing these scratches in the finished coat. If you are using Silicon Carbide Papers (Wet and Dry) you might have to go up a grade or two because these papers are very sharp and can leave deep scratches. Remember half the battle is in the quality of the prep! & &
5 Marineware is a long standing distributor of International and other Akzo Nobel paints. International has a long history of providing protective coatings to steel vessels worldwide. PRIMER Step 1: Epoxy Primer (820 or 670 HS) UNDER COAT Step 2: Perfection Pro Under coat TOP COAT Step 3: Perfection Pro Number of coats 1-2 coats 2-3 coats 2-3 coats Thinners GTA 220 YTA 910 YTA 100 Drying times 6-12 / 10-24 hours 2-3 hours Touch dry 7-17 hours Abrasive paper See datasheet P180-220 P400 Perfection Pro undercoat can be overcoated without sanding during the overcoat window.* APPLICATION KEY *Always check technical data sheets & &
6 Launched only 5 years ago, Perfection Pro has already established itself as a favourite with traditional applicators. This modern polyurethane topcoat is designed for professionals and due to its unique resin base, exhibits post flow like nothing else. When applied correctly this system has the potential to surpass sprayed finishes in terms of gloss and distinction of image. Perfection Pro can be applied and laid off with only a roller, tipped off with a brush (most colours) and is also available in a spray version. Perfection Pro 2 Pack System Available in 195 RAL colours as well as the 12 traditional International Perfection colours there is a pallet to meet the most demanding owner’s needs. Please contact us for a colour card. Part No Product YSC032/1HGLT International Perfection Pro Curling Agent 0.5 US Gallons (For 1 US Gallon Colour Basis) YSC032/1PT International Perfection Pro Curling Agent 1 Pint (For 1 US Quart Colour Basis) YSC032/1PT International Thinners 100 For Perfection Pro 1L 73015 X138 Procure Inhibited Accelerator Base Converter Thinner 2 1 5-10% & &
7 Perfection Pro Undercoat International Perfection Pro undercoat is designed specifically for hand application under Perfection Pro topcoat. This polyurethane undercoat is very fast drying, allowing overcoating with itself as soon as just one hour, or sanding and overcoating with Perfection Pro topcoat in as little as 2 hours. Top Tip: The white and black bases can be mixed to create a grey tone of your choosing. Providing a smooth and consistent surface finish this product is essential for obtaining the best possible surface for International Perfection Pro. Perfection Pro Undercoat is a three-part system consisting of a coloured base, a convertor and then an activator. The mix ratio for this is 3 part base to 1 part convertor and then activator at 10% of the volume of the base/convertor mix. Part No Product YSC250/3LT International Perfection Pro Undercoat White 2.785L YSC251/3LT International Perfection Pro Undercoat Black 2.758L YSC249/1 International Perfection Pro Converter 0.94L YSC248 International Perfection Pro Activator 0.94L Base Converter Activator 3 1 10% & &
8 Interseal 670HS is a low VOC two-component surface tolerant epoxy high build primer. 670HS can be applied by roller or both conventional and airless spray and with its high tolerance to surface, imperfections can protect both hand and blast-prepared steel. A good overcoating window for itself and topcoat systems means the application of the Perfection Pro system can continue without the need for adhesion sanding. Interseal 670HS Epoxy Primer Available in 5L and 20L kits Interseal 670HS comes in silver grey (Ral7001) as standard and is available in some RAL colours to special order (1-2 week lead time). Contact us for more information. Interseal 670HS can be thinned 5-10% for a smoother application, we would typically expect 6m²/LT of mixed product at 125 micron DFT. Part No Product EGA130/A5LT Interseal 670HS 5LT Pack – Silver Grey EGA130/A20LT Interseal 670HS 20LT Pack – Silver Grey GTA220/5 Internationals No 7 thinner for epoxybased products such as 820 and 670 Base Converter Thinners 2 1 5-10% & &
9 International Intergard 269 International Interprime 820 Intergard 269 is a two-pack, fast-drying epoxy primer that can withstand prolonged periods of weathering before overcoating making it an ideal blast primer. The perfect solution for protecting blasted steel, including shells and components. Intergard 269 is an epoxy primer with an extended overcoating window, allowing the user to overcoat the primer without sanding for a period of up to six months. See data sheet or contact us for specific advice on overcoating. Part No Product EGA088/A5 International Intergard 269 Red 5L Pack EGA088/A20 International Intergard 269 Red 20L Pack Interprime 820 is a high performance 2-component epoxy primer containing inert pigments and extenders for use on blasted steel substrates above and below the waterline. Part No Product YPA828/5LT EGA088/A20 YPA829/5LT EGA088/A20 EGA088/A20 EGA088/A20 EGA088/A20 EGA088/A20 EGA088/A20 EGA088/A20 EGA088/A20 EGA088/A20 & &
10 A quick drying, single pack primer. Ideal for use under Interlac 665, this primer is an economical choice for priming boats undergoing regular maintenance. International Interstores Alkyd Primer One UP is a single-pack primer/undercoat for use above the waterline with International onepack finishes and deck paints. Simple yet effective, making painting easier for DIY customers without compromising on aesthetic appearance or substrate protection. Part No Product ISA710/5LT International Interstores Alkyd Primer White 5L ISA710/20LT International Interstores Alkyd Primer White 20L ISA720/5LT International Interstores Alkyd Primer Grey 5L ISA720/20LT International Interstores Alkyd Primer Grey 20L ISA730/5LT International Interstores Alkyd Primer Red 5L ISA730/20LT International Interstores Alkyd Primer Red 20L International One UP Part No Product YUC000/750AA International One Up White 750 MOQ YUC000/2.5 International One Up White 2.5LT YUC001/750AA International One Up Blue Grey 750 Step One Step Two Product One Up Toplac Plus Number of coats 2-3 2-3 Thinner No 1 YTA 100 Drying Time 6 hrs - 7 days 8 hrs - 2 days & &
11 International Toplac Plus Toplac Plus is a silicone alkyd premium gloss yacht enamel for all substrates above the waterline. This modern product is easy to apply by roller without the need for tipping, achiving a similar flow out to Perfection Pro. Toplac Plus contains the latest UV filters for increased durability and longevity. Toplac Plus can be used as a stand alone system using the one-up primer or straight over Perfection Pro for stripes and details. Part No Product YLK000/750ML International Toplac Plus 750ML Snow White YLK993/750AA International Toplac Plus 750ML Oxford Blue YLK184/750ML International Toplac Plus 750ML Med White YLK265/750M International Toplac Plus 750ML Rescue Orange YLK898/750ML International Toplac Plus 750ML Bondi Blue YLK101/750ML International Toplac Plus 750ML Yellow YLK999/750ML International Toplac Plus 750ML Jet Black YLK684/750AA International Toplac Plus 750ML Atlantic Grey YLK504/750ML International Toplac Plus 750ML Fire Red YLK299/750AA International Toplac Plus 750ML Rochelle Red YLK541/750AA International Toplac Plus 750ML Donegal Green Part No Product YTA100/1LT International Thinners 100 1LT YTA100/500 International Thinners 100 500ML & &
12 An economical alkyd based single pack gloss enamel. Ideal for gloss finishing on hire fleets or boats undergoing regular maintenance. Available in RAL colours. International Interlac 665 International Intertuf 16 Part No Product CLB***/5 International Interlac 655 5LT CLB***/20 International Interlac 655 20LT The industry standard in hull blacking, International Intertuf 16 is a high build bituminous coating designed for the economical protection of steel surfaces on ships. Adopted many years ago by inland water vessels, Intertuf 16 is the ideal protective and maintenance coating for hull blacking. Part No Product JBA016/5 International Intertuf 16 Black 5L JBA016/20 International Intertuf 16 Black 20L Part No Product Where to use GTA004/5 International Thinner No.1 A general purpose thinner that can be used with Intertuf Alkyd Primer and Interlac 665. (See technical datasheets.) GTA220/5 International Thinner No.7 A thinner for epoxy-based products such as 820 and 670. YTA910/5 International Thinner 910 A fast evaporating thinner for polyurethane based products - can be used to reduce Perfection Pro Undercoat. (Not normally required.) YTA920/5 International Thinner 920 A slow evaporating thinner for polyurethane based products - can be used to reduce Perfection Pro Undercoat. (Not normally required.) YTA100/1 International Thinner 100 Thinners for Perfection Pro Topcoat. International Thinners & &
13 MARINE PAINTS If you know classic boats you will know Epifanes. With a full range of paint products from classic colours and golden varnishes to modern two pack products, Epifanes has all the colours to bring out the beauty of any boat. The range can be split into two clear ranges. The single pack products which are more tolerant of less than perfect conditions, and the two pack polyurethane range which can be more challenging to get a good finish but is harder wearing and provides longer lasting results. Ease of application Ease of maintenance Gloss level and gloss retention Abrasion and scratch resistance One-Component Paint System Two-Component Paint System ***** ***** **** *** *** *** ***** ***** The choice between one-component and two -component finishes depends primarily on the type of substrate to be coated. The existing paint system in the case of maintenance and to a lesser extent the working conditions underwhich the paint has to be applied (temperature / relative air humidity). A one-component system provides ease of application, is more tolerant regarding the existing paint and can be applied with good results in a wider range of temperatures. A two-component finish is harder and more durable, but is more demanding regarding application skills and working conditions. & &
14 One-Component Paint System Epifanes Multi Marine Primer Epifanes Yacht Enamel & Epifanes Multiforte Number of coats 3 3 Thinner Epifanes thinners for paint & varnish Epifanes thinners for paint & varnish Drying time 18 hours 24 hours Abrasive paper P220-dry P400-wet Remarks Thin first coast by 25% and apply with a stiff brush Thin first coast by 5-10% Two-Component Paint System Epifanes Epoxy Primer or Epifanes Multicover Epifanes Poly-urethane Number of coats 3 3 Thinner Epifanes Thinner D-601 Epifanes Poly-urethane brush thinner Drying time 8 hours 24 hours Abrasive paper See remarks P400-wet Remarks Thin first coat by 25% and apply with a stiff brush. Allow final coat 24 hours to cure. In the case of Epoxy Primer, sand final coat with P180-P220 Thin first coat by 5-10%. Over- coat within 49 hours without sanding. If overcoated after 48 hours, always sand. & &
15 Famous for some of the world’s finest enamels and varnishes, Epifanes are synonymous with quality finishes for truly classic coach painting. The last word in traditional marine finishing, Epifanes Bootlak (Yacht Enamel) is a single-pack, alkyd gloss for the ultimate classic look. A stalwart of coach painters on the inland waterways of both Holland and the UK. Available in a wide standard colour range as well as most RAL colours by special mix – 750ml and 2L tins. •Watch out for cold spells and direct sunlight •Try to paint during the middle of the day to avoid condensation. •Use good quality brushes and rollers. •A little extra time to make sure masking tape is pressed down will improve lines and details. •Use correct thinners as they are cleaner than cheap alternatives Epifanes Yacht Enamel Part No Product YE### Epifanes Bootlak Yacht Enamel - standard 48 colours 750ML YE###/2L Epifanes Bootlak Yacht Enamel - Standard colours 2L YESPMIX750-RAL#### Epifanes Bootlak Yacht Enamel - RAL colours 750ML YESPMIX2L-RAL#### Epifanes Bootlak Yacht Enamel - RAL colours 2L Painting Tips & &
Epifanes Yacht Enamel Colour Chart 16 & &
The hardness and durability of urethane resin with the same ease of use as Yacht Enamel. Epifanes Mono-urethane provides the ultimate longevity and gloss retention for single-pack finishes. Offering faster initial curing than Yacht Enamel, this paints hybrid resin formulation delivers a tough high gloss topcoat with excellent durability. Epifanes Mono-urethane 17 Available in 750ml sized tins Special mix colours 750ML & 2L & &
Epifanes Mono-urethane Colour Chart 18 & &
19 Epifanes Multiforte The paint for coach roofs, decks and gunwales. Epifanes Multiforte is a hard-wearing, semi-gloss single-pack available in a wide range of colours. Perfect for use on steel substrates where an abrasion-resistant topcoat is required. Ideal for use on coach roofs where a gloss finish is not desirable. Available in standard colours or RAL special mixes, and its fast through cure helps prevent microblisters. Multiforte is an amazing paint for canal boat roofs, its low sheen finish reduces glare and its fast-dying properties help speed up the job. Works really well with the Epifanes non-skid additive. Part No Product Epi-Multiforte-White Epifanes Multiforte White 4L Epi-Multiforte-R.Bro Epifanes Multiforte Red Oxide 4L Epi-Multiforte-M.Gre Epifanes Multiforte Medium Grey 4L Epi-Multiforte-Light-Grey Epifanes Multiforte Light Grey 4L Epi-Multiforte-Dark-Grey Epifanes Multiforte Dark Grey 4L Epi-Multiforte-Cream Epifanes Multiforte Cream 4L Epi-Multiforte-Blue Epifanes Multiforte Blue 4L Epi-Multiforte-Black Epifanes Multiforte Black 4L Epi-Multiforte-218 Epifanes Multiforte Jade Green 4L Epi-Multiforte-Ralmix Epifanes Multiforte Mixed to Ral Colour 4L Closest colour match to Epifanes Yacht Enamel (YE) colours: MF Light Grey – YE 212 MF Mid Grey – YE 213 MF Dark Grey – YE 214 MF Dark Brown – YE35 MF Electric Blue – YE 28 These colours are similar to Epifanes YE, but may vary slightly to the actual paint. & &
20 Epifanes Non-Skid Deck Coating A single-pack, semi-gloss deck paint. Epifanes Non-Skid Deck Coating is based on monourethane with the addition of a measured amount of polypropylene beads to provide a tough, semi-gloss, non-skid finish. For the best finish apply over two coats of gloss. Part No Product NS213/2L Epifanes Non Skid Enamel Dark grey 213 2L NS213 Epifanes Non Skid Enamel Dark grey 213 750ML NS212/2LT Epifanes Non Skid Enamel Light Grey 213 750ML NSW Epifanes Non Skid Enamel White 750ML NS1 Epifanes Non Skid Enamel Cream 750ML NS212 Epifanes Non Skid Enamel grey 212 750ML Epifanes Bilge Paint A single-pack paint for bilge spaces and engine rooms. Epifanes Bilge paint is an easy-to-apply, single-pack, tough paint. It can be applied over most substrates with the appropriate primer. Part No Product EBIL/750 Epifanes Bilge Paint White 750ML EBIL/2L-White Epifanes Bilge Paint White 2L EBIL/750-Grey Epifanes Bilge Paint Grey 750ML EBIL/2L-Grey Epifanes Bilge Paint Grey 2L & &
21 Epifanes Multimarine Primer A single-pack primer designed for application to all common substrates offering easy protection for surfaces above the waterline. Epifanes Multimarine Primer combines the characteristics of separate substrate primers in one product. Excellent adhesion to wood, metal, GRP, and most previously painted surfaces. For use above the waterline on interior and exterior surfaces. Part No Product EMMW/750 Epifanes Multi Marine Primer White 750ML EMMMW/2L Epifanes Multi Marine Primer White 2L EMMW/4L Epifanes Multi Marine Primer White 4L EMMR/750 Epifanes Multi Marine Primer Red Brown 750ML EMMR/2L Epifanes Multi Marine Primer Red Brown 2L EMMG/750 Epifanes Multi Marine Primer Grey 750ML EMMG2L Epifanes Multi Marine Primer Grey 2L EMMG/4L Epifanes Multi Marine Primer grey 4L & &
22 Epifanes Non-Skid Deck Coating A very high gloss two-pack poly-urethane coating. Epifanes poly-urethane can be applied by roller/brush or spray to provide a finish with an extremely high gloss level that is also very durable and scratch resistant. Standard colours are available from stock with special custom colours and satin variants, sourced directly from Epifanes to ensure consistent, high-quality mixes. For more information, please contact us. Epifanes Epoxy Primer A two-pack anticorrosive epoxy primer with zinc phosphate. The ideal substrate primer for twopack gloss poly-urethane. Epifanes Epoxy Primer is great for priming steel above the waterline. Epifanes Poly-urethane Hints & Tips Allow 15 minutes for the paint to induct after mixing Use good quality rollers, they will last longer in two-pack thinners. Try not to overlook the paint Ensure you’re wearing the correct PPE 2 PACK PRIMERS Epifanes Multicover Primer A multipurpose quick-drying epoxy primer with excellent adhesion to multiple substrates. Part No Product E12 Epifanes Epoxy HS Primer White 750ML E12/2L Epifanes Epoxy HS Primer White 2L E12/4L Epifanes Epoxy HS Primer 4L Part No Product E1MCG.4 Epifanes Multicover Primer Grey 4L EMCG.750 Epifanes Multicover Primer Grey 750ML & &
Epifanes Poly-urethane Colour Chart 23 & &
24 Epifanes Gloss Varnish Epifanes Clear Gloss Varnish, famous worldwide for its classic amber hue and excellent outdoor durability. Its flexibility prevents cracking on working wood and famous for its high gloss retention and classic look. Epifanes Rubbed Effect is a single-pack satin varnish designed for interior application over build-up coats of an Epifanes Gloss Varnish system. SINGLE PACK VARNISH Part No Product E1 Epifanes Gloss Varnish 1L E2 Epifanes Gloss Varnish 500ML E3 Epifanes Gloss Varnish 5L E36 Epifanes Gloss Varnish 250ML Epifanes Rubbed Effect Varnish Part No Product E7 Epifanes Rubbed Effect Varnish 500ML E6 Epifanes Rubbed Effect Varnish 1L E6/5L Epifanes Rubbed Effect Varnish 5L & &
25 Epifanes Rapid Varnish Range A selection of wood finishes for use in quick-build interior or exterior varnish systems. Epifanes Rapid Clear Epifanes Rapid Clear is a clear semi-gloss, single-pack wood finish designed for rapid overcoating without the need for intercoat sanding. (See datasheet) Part No Product Epifanes-Rapidcoat/Clear Epifanes Rapidclear 750ML Epifanes-Rapidclear Epifanes Rapidclear 4L Epifanes Rapid Coat Epifanes Rapid Coat is a semi-gloss single-pack wood finish, with a light teak tone. Also designed for rapid overcoating without intercoat sanding. Part No Product Epifanes-Rapidcoat Epifanes Rapidcoat 750ML Epifanes Rapid Matt Epifanes Rapid Matt is a clear matt, single-pack wood finish also designed for rapid overcoating and achieving a matt finish with the above systems. Part No Product Epi-Rapid-Matt Epi-Rapid-Matt & &
26 Additives A multi-purpose additive or stand-alone coating based on a selection of natural oils. Suitable for use in one-component conventional and half-synthetic varnishes, paints, and primers to optimize impregnation/saturation and preservation on the surface. Flow enhancer under cold or hot working conditions. Epifanes Easy Flow Epifanes Through Drying Additive Specifically formulated to speed up the through-drying of Epifanes traditional one-components paints and varnishes when applied at low temperatures, allowing sanding the next day. (For professional use only) Part No Product ETDA Epifanes through drying additive 500ml Part No Product E/Flow/500 Epifanes Easy Flow 500ML E/Flow/1LT Epidanes Easy Flow 1L & &
27 Epifanes One Pack Spray Thinner Spray thinner for all Epifanes single-pack products. This can also be used as a surface cleaner. Part No Product E15 Epifanes Spray Thinner for Paint & Varnish 1L E15/5L Epifanes Spray Thinner for Paint & Varnish 5L Epifanes D601 Thinner Brush/roll and spray thinner for Epifanes epoxy primers. Part No Prodcut E19 Epifanes Epoxy Thinner D601 500ML E18 Epifanes Epoxy Thinner D601 1L E18/5L Epifanes Epoxy Thinner D601 5L & &
28 Epifanes Non-Skid Beads 20G Polypropylene non-skid beads can be added to Epifanes to produce a non-skid surface. Stir in gradually, allow 15 minutes and stir once more. Apply by roller as brushing will not produce an even coat. Epifanes Rust Remover Epifanes Paint & Varnish Thinner Single-pack reducer designed for brush and roller application. Part No Product E24 Epifanes Paint and Varnish Brush Thinner 500ML E14 Epifanes Paint and Varnish Brush Thinner 1L E27 Epifanes Paint and Varnish Brush Thinner 5L Part No Product ENSB/20G Epifanes Non-Skid Beads 20G Part No Product ERR/500 Epifanes Rust Remover 500ML Epifanes Rust Remover is a rust transformer based on water-repellent polymers. It’s non-toxic and non-flammable. It stops corrosion, transforms rusted steel into a sound base for painting, and promotes and improves the adhesion of the subsequent paint coat. Especially useful for those hard to prep areas. & &
29 Epifanes Polyurethane Thinners Epifanes brush and spray thinners for use with Epifanes PU top coat and primers. Epifanes spray thinners can also be used as a surface cleaner and is for professional use only. Part No Product E25 Epifanes Polyurethane Brush Thinner 500ML E49 Epifanes Polyurethane Brush Thinner 1LT E16/5 Epifanes Polyurethane Brush Thinner 5LT E26 Epifanes Polyurethane Brush Thinner 1L E17 Epifanes Polyurethane Brush Thinner 5L Conditions during application and drying Minimum Temp Maximum Temp Max Relative Air 1-comp. primers 10°C / 50°F 25°C / 77°F 85% 2-comp. epoxy primers/coatings 15°C / 59°F 25°C / 77°F 70% 1-comp. finishing top coats 5°C / 41°F 30°C / 86°F 85% 2-comp. poly-urethane top coat 12°C / 54°F 25°C / 77°C 70% Paying attention to working conditions & &
30 Resene Acrythane Topcoats New Zealand-based Resene are well known throughout the marine industry for their steadfast primer Durepox. Our range of Resene coatings offers manufacturers and professional finishers a versatile and fast solution for the complete painting of inland water vessels. Resene Acrythane offers professional painters a versatile solution for two-pack finishing on inland water vessels. Unlike two-pack polyurethanes, which cannot be polished without incurring some damage, Acrythane’s acrylic urethane formulation can be easily buffed to allow the blending of repairs and restoration of gloss. With a wide colour range, Acrythane is the ideal spray applied two-pack system for manufacturers and professional painters alike. Also available as a clear lacquer. For colours visit: www.resene.co.nz/swatches/ Before your get started! Take time to check over your spray guns and airlines. Over time, parts wear and need replacing. Don’t leave this to the last minute. Invest in a spare air cap, tip and needle. Resene Acrythane A professional Acrylic Urethane two-pack topcoat, providing a high gloss finish that can be polished and easily repaired. Acrythane colours are available in 2L bases Part No Product DURA-HAC01 Durepox Acrythane Hardener 1L DURA-HAC250 Durepox Acrythane Hardener 250ML DURA-R90901/1L Durepox Reducer 909 1L DURA-R91001 Durepox Acrythane 910 Reducer Slow 1L DURA-TPC04 Durepox Acrythane Clear 4L & &
31 Durepox Primers Durepox is a mainstay of our wider product range. Born from the world of yacht racing, Durepox is an excellent primer and solid base for two-pack top coats such as Acrythane. Easily sanded (within 48 hours), Durepox hardens to become a very durable, abrasion-resistant primer. It can be applied directly to suitably prepared steel and can be tinted to many colours including RAL. Part No Product DURA-DUW04 Durepox White Base 4L DURA-DUB04 Durepox Black Base 4L DURA-DUG04 Durepox Grey Base 4L Part No Product DURA-HDX01 Resene Durepox Hardener 1L DURA-HDX05 Resene Durepox Hardener 5L DURA-R400N01 Resene 400 Reducer Standard 1L DURA-R400N04 Resene 400 Reducer Standard 4L DURA-R4000S01 Resene 400 Reducer Slow 1L DURA-R4000S04 Resene 400 Reducer Slow 4L Resene Durepox Hi Solids is a high-build primer that can be applied to suitably prepared steels. Like standard Durepox, its epoxy urethane fomulation provides a stable and abrasionresistant base for two-pack top coats. Ideal for quickly building primer thickness on new or stripped vessels. An accelerator for Resene two-pack paint systems. 62C Accelerator can be used in both Durepox and Acrythane. Up to 5% will approximately half curing times and pot life. Part No Product DURA-DHSW04 Resene Durepox Hi-Solids Primer Part No Product DURA-A62C01 Resene 62C Accelerator 1L & &
Marineware was founded in 1986 and has since been supplying the marine industry with products from some of the world’s biggest brands such as; Awlgrip, International, Gurit, Epifanes, Nautix, Durepox and Propspeed. We have been the exclusive supplier of Awlgrip in the UK for the last 35 years, and we mix all topcoat colours in house. We have a 7-person technical team based all over the country with a combined experience in the marine and paint industry in excess of 150 years. Our technical team are happy to visit your site and advise on any improvements you may wish to make to your facilities or process, and there is always someone available at the other end of the phone to answer any questions. Our team conducts regular training courses for customers, either on-site at customer locations or at the DeVilbiss technical centre in Bournemouth. We have access to the Akzo Nobel Global Technical team for difficult jobs, and if things don’t go to plan we also have NACE-qualified paint inspectors on staff with a plethora of test equipment to help diagnose and remedy issues both during and after. & &