Newman Product Catalog

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
FASTENER TECHNICAL DATA & CHARTS

Standard Stainless Steel Specifications TOOLS &
ACCESSORIES
Type 301: Cr. 18, Ni. 8 (18-8 type), austenitic, hardenable by cold work Type 410: Cr. 12 (straight chromium type), hardenable by heat treatment;
only; t.s., 80-270,000 psi: y.s. 30-240,000 psi.; elongation in 2 in., 40- t.s., 60-180,000 psi: y.s.30-160,000 psi.; elong. in 2 in., 30-15%, good CONTRACTOR
5%. In rods, bars, billets, wire, sheet, plate, strip and tubing. For parts machinability, cold forming properties; good welding properties when SUPPLIES
requiring good corrosion resistance combined with high tensile strength annealed; most popular forging grade. In sheet, strip, plate, bar, rod, forg-
and good ductility. ing billets, tube rounds, tubing, cold drawn and structural shapes. Used hangers
Type 302: Cr. 18, Ni. 8 (18-8 type), austenitic, hardenable by cold work where corrosion not severe, for bolts, nuts, shafting turbine blading, valve & strut
only; t.s. 80-250,000 psi.; y.s. 30-225,000 psi.; elongation in 2 in., 60- trim, heat treated parts; where hardness, toughness, desired.
5%; fair machinability excellent cold forming and welding properties. Type 416: Cr. 12 (straight chromium type with sulphur or selenium fasteners &
Furnished in sheet, strip, plate, bar, rod, forging billets and tube rounds, added); excellent machinability; t.s., 70-170,000 psi; y.s., 4-140,000 threaded rod
tubing, cold drawn shapes and structural shapes. For parts in acid handling psi; elong. in 2 in. 30-10%; fair cold forming properties, fair corrosion
food and dairy equipment; shafting, bearing plates, heat exchanger tubes, resistance. In bar, rod, forging billets, wire, cold drawn shapes. For mass concrete
hydraulic tubing, piston rods, plungers, etc. production machined parts; Carburetor, instrument and electrical parts; anchors
Type 303: Cr. 18, Ni. 8 (18-8 type), austenitic, hardenable by cold work screw machine parts.
only; t.s., 80-200,000 psi.; y.s. 30-135,000 psi.; elong. in 2 in. 55-10%; Type 420: Cr. 13, C. 35; a widely used stainless cutlery steel. In the specialty items
good machinability; fair cold forming and welding properties. In sheet, hardened and tempered condition, it combines an adequate hardness services & data
strip, plate, bar, rod, forging billets, tube rounds, tubing, cold drawn and and cutting edge with good flexibility. It retains a bright polished finish
structural shapes. For working parts in pumps and valves which must and can be hardened io Rockwell C55. Maximum corrosion resistance
resist corrosion; screw machine parts requiring strength, good corrosion is obtained in the hardened condition.
resistance. Type 420F: Cr. 13, C.35; free machining; has sulphur intentionally added
Type 304: Cr. 18, Ni. 8 (18-8 type), austenitic, hardenable by cold work to the base Type 420 analysis to make it easier to machine, grind and
only; t.s., 85-250,00 psi; y.s., 30-225,000 psi; elongation in 2 in. 60-5%; polish. Type 420°F has practically the same mechanical hardness, and
slightly better corrosion resistance than Type 302. Furnished in rods, bars, corrosion resisting properties as Type 420.
billets, wire, sheet, plate strip, tubing and castings. For parts in chemical Type 430: Cr. 17 (straight chromium type), non-hardenable by heat
equipment such as shafting, bearing plates, heat exchanger tubes, etc. treatment; resists scaling to 1500°F; excellent cold heading properties,
Type 309: Cr. 25, Ni. 12 (25-12 type), austenitic, hardenable by cold work excellent machinability; does not discolor in atmosphere. t.s., 60-85,000
only; t.s., 95-190,000 psi.; y.s. 45-165,000 psi.; elong. in 2 inches, 50-5%; psi.: y.s. 35-55,000 psi.; elongation in 2 in. 35-20%. Furnished in sheet,
resists scaling to 2000°F, fair machinability, good cold C forming proper- strip, plate, bar, rod, forging billets, tube rounds, tubing, cold drawn shapes
ties, excellent weldability. Furnished in sheet, strip, plate, bar, rod, forging and structural shapes. For press plates, oil burner parts, screw machine
billets, tube rounds, tubing, cold drawn shapes and structural shapes. For parts, trim for automobiles such as body moldings, hub caps, finishing
parts that must operate continuously at high temperatures; oil burner parts, washers, gas tank caps, etc.; also trim for appliances.
furnace parts, heat exchangers, air heaters, baffle plates, etc. Type 430F: Cr. 17 with 0.07 S. or Se.; straight chromium free machining
Type 310: Cr. 25, Ni. 20 (25-20 type), austenitic, hardenable by cold work type, non-hardenable by heat treatment; t.s., 60-85,000 psi.: 35-55,000
only; t.s., annealed, 70-155,000 psi.; elong. in 2 in., 55-5% good weld- psi.: elong. in 2 in., 25-10% excellent machinability, fair cold forming
ability, drawing, stamping properties; fair machinability. In sheet, strip, properties. In forging billets, hot-rolled and cold-finished bars, wire and
plate, bar, rod, forging billet, tube rounds, tubing, cold drawn, structural polished shafting. Particularly suitable for parts requiring considerable ma-
shapes. For parts subject to intermittent heating and cooling; oil burner chining and only moderate corrosion resistance; screw machine parts.
parts, heat exchangers; dye house, paper mill, chemical equipment. Type 431: Cr. 16, Ni. 2 (straight chromium type), hardenable by heat
Type 316: Cr. 18, Ni. 12, No. 3 (18-12-3 type), austenitic, hardenable by treatment: t.s., 110-200,000 psi.; 80-150,000 psi.; elongation in 2 in.,
cold work only; t.s., 80-170,000 psi; y.s., 35-150,000 psi; elong. in 2 in., 20-15%: good machinability; fair cold forming properties: resists scaling
55-5% fair machinability; excellent welding, cold forming properties. Best to 1500°F. Best corrosion resistance of all hardenable stainless steels.
creep strength at high temp. and best corrosion resistance of all grades. Furnished in sheet, strip, plate, bar, rod, forging billets, tube rounds, tub-
In sheet, strip, plate, bar, rod, forging billets, tube rounds, tubing, cold ing, cold drawn shapes, structural shapes. For parts requiring excellent
drawn and structural shapes. physical properties coupled with high corrosion resistance.
Type 321: Cr. 18, Ni. 8, Ti. 4 x C min.; austenitic hardenable by cold Type 440 C and 440 A, B and C: Cr. 17, C 1.00 (straight chromium type)
work only; t.s., 80-170,000 psi.; y.s., 30-145,000 psi.; elong. in 2 in., hardenable by heat treatment: t.s., 110-285,000 psi; 60-275,000 psi.:
55-5%; fair machinability, excellent welding and cold forming proper- elong. in 2 in., 15-21%; fair machinability., cold forming properties. Types
ties. In sheet, strip, plate, bar, rod, forging billets, tube rounds, tubing, A, B, same analysis except for lower carbon content: less hardenable;
cold drawn shapes, structural shapes. For welded parts not annealed Type F, free machining. In sheet, strip, plate, bar, rod, forging billets, tube
after welding or which operate at 800-1200°F; aircraft engine exhaust round tubing, cold drawn and structural shapes; needle, ball check valves;
rings, flanges, etc. ball bearings, scissors, rules, cutlery, etc.
Type 347: Cr. 8, Ni. 18, Cr. 8 x C min.; austenitic, hardenable by cold work Types 501 and 502: Type 501, 4/6 Cr. plus Mo. over .10 C. Type 502, 4/6
only; t.s. 80-170,000 psi.; y.s., 30-150,000 psi.; elong. in 2 in. 50-5%; fair Cr. plus Mo., over .10 C. maximum. Both types are recommended for
machinability, excellent welding and cold forming properties. In sheet, use in the petroleum industry. In refinery equipment, particularly where
strip, plate, bar, rod, forging billets, tube rounds, tubing cold drawn and sour crudes are encountered, a life of four to ten times that of mild steel
structural shapes. For welded parts not annealed after welding or which is not uncommon. These alloys are suitable for use at slightly elevated
operate at 800-1200°F; aircraft engine exhaust rings, flanges, etc. temperatures, and are more resistant to scaling or oxidation that is mild
steel. Scaling temperature about 1150° Fahrenheit.

299
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
FASTENER TECHNICAL DATA & CHARTS

Industry Standards and Specifications

TOOLS & Industry Standards Basic Fastener Types
ACCESSORIES Most industrial fasteners are covered by two basic
standards: one for materials and properties; the other, for A Bolt is a device with a head on one end of a shank or
CONTRACTOR dimensions and tolerances. Specifications for materials body and a thread on the other end. Designed for insertion
SUPPLIES and properties are published by the American Society for through holes in assembly parts, it is mated with a tapped
Testing and Materials (ASTM), although other groups such nut. Tension is normally induced in the bolt to compress
hangers as the Society of Automotive Engineers (SAE) also publish the assembly by rotating the nut. This may also be done
& strut specifications covering these requirements. by rotation of the bolt head.

fasteners & Standards for dimensions and tolerances are issued by A Screw is a headed and threaded bolt used without a nut.
threaded rod the American National Standards Institute (ANSI) in It is inserted into an internally tapped hole and tension is
cooperation with the American Society of Mechanical induced by rotation of the screw head.
concrete Engineers (ASME) and the Industrial Fasteners Institute
anchors (IFI). A Stud is a fastener with no head but it has threads at
both ends of the shank. It, like a screw, has one end that
specialty items Where applicable, published specifications covering a screws into a tapped hole. A nut is used on the other end
services & data particular fastener will be referenced in the section of this to create tension.
booklet dealing with that fastener.
If a stud is threaded its entire shank length and a nut used
When referring to standards and specifications, we will on both ends to create tension, it serves the function of a
use only the well-known initials of the above societies- bolt and is then classified as a Stud Bolt.
ANSI, ASME, IFI, ASTM and SAE.
Many variations of these
Standard fasteners are basic industrial fasteners - square basic fastener types are available.
and hex bolts, cap screws, carriage bolts, plow bolts, lag
screws, studs, nuts, rivets and others - which have been
standardized over the years as to type‘, style, usage,
properties, dimensions and tolerances.

These include a vast range of sizes and types stocked by
distributors and manufacturers for an almost limitless
range of applications: the assembly and maintenance
of vehicles, appliances, farm equipment, construction
equipment, industrial and plant machinery of all kinds,
furniture and toys.

Wherever there’s a need for holding parts together, holding
them apart, holding them up, or holding them down,
a standard fastener can usually be found to do the job
efficiently and economically.

Modern industrial fasteners are manufactured to a variety
of standards covering dimensions, tolerances, materials,
mechanical properties, testing procedures, etc.

300
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
FASTENER TECHNICAL DATA & CHARTS

Basic Fastener Data STYLES OF HEAD TOOLS &
TERMINOLOGY & MEASUREMENTS ACCESSORIES
­

head shank thread nut point Round Round
Countersunk (button)
Square Hex

dia. CONTRACTOR
SUPPLIES
head gaging thread
length length

bolt length

Standard hex bolt with hex nut hangers
& strut
The diameter of all bolts is measured as the outside HEAVY HEADS AND NUTS
of major diameter of the thread. The length of a Bolt users may require a bolt head or nut of greater fasteners &
headed bolt is measured from the largest diameter width to compensate for wide clearance in bolt threaded rod
of the bearing surface of the head to the extreme holes or unusually heavy loading. For such needs
end of the point in a line parallel to the axis of the we offer heavy bolt heads or nut sizes. Heavy nuts concrete
bolt. For example, square or hex head bolts are are quite common and readily available in various anchors
measured from under the head to the end of the types and sizes but heavy head bolts have more
bolt; a bolt with a countersunk head is measured limited availability.
overall. The point of a bolt is always included in
the measured length. BOLT AND NUT BEARING SURFACES
Cold-upset bolts made on a “boltmaker” usually
Headless fasteners such as studs are measured are washer faced but large or very long bolts may
overall, including points, except for continuous- have a flat face (not machined). Nuts made on
thread alloy studs made to ASTM Specification cold “nut-formers” may have double chamfered
A193. This type is measured from first thread to or washer faces. Large size nuts have hot-forged
first thread. washer bearing faces, not machined, unless
specially ordered.
Bolts have various styles of heads. Some of the more
popular styles are illustrated above. specialty items
services & data

301
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
FASTENER TECHNICAL DATA & CHARTS
TOOLS &
ACCESSORIES Heat Treatment and Mechanical Properties

CONTRACTOR HEAT TREATMENT
SUPPLIES
Heat treatment covers various techniques that may be used to develop certain end-product characteristics.
hangers Customary procedures for fasteners include annealing, stress relieving, case hardening, direct quench and
& strut temper, and carbon restoration.

fasteners & Annealing: A thermal cycle involving heating to, and holding at a suitable temperature and then cooling
threaded rod at a suitable rate, for such purposes as reducing hardness, improving machinability, facilitating cold working,
producing a desired microstructure, or obtaining desired mechanical or other properties.
concrete
anchors Stress Relieving: A thermal cycle involving heating to a suitable temperature, usually 1000/1200°F,
holding long enough to reduce residual stresses from either cold deformation or thermal treatment, and then
specialty items cooling slowly enough to minimize the development of new residual stresses.
services & data
Case Hardening: A term descriptive of one or more processes of hardening steel in which the outer
portion, or case, is made substantially harder than the inner portion, or core. Most of the processes involve
either enriching the surface layer with carbon and/or nitrogen, usually followed by quenching and tempering,
or the selective hardening of the surface layer by means of flame or induction hardening.

Quenching and Tempering: A thermal process used to increase the hardness and strength of steel.
It consists of austenitizing, then cooling at a rate sufficient to achieve partial or complete transformation
to martensite. Tempering should follow immediately, and involves reheating to a temperature below the
transformation range and then cooling at any rate desired. Tempering improves ductility and toughness, but
reduces the quenched hardness by an amount determined by the tempering temperature used.

MECHANICAL PROPERTIES

Standard industrial fasteners are manufactured from either carbon or alloy steels. When strength requirements
are moderate, low-carbon steel is used. High-strength fasteners are made from medium-high carbon or alloy
steels and are heat treated to develop desired properties. Most fasteners are covered by specifications that
define required mechanical properties such as tensile strength, yield strength, proof load, and hardness.

Tensile Strength: The maximum tensile stress in pounds per sq. in. which a material is capable of
sustaining, as developed by a tension test.

Yield Strength: The stress at which a material exhibits a specified deviation from the proportionality of
stress to strain. The deviation is expressed in terms of strain, and in the offset method, usually a strain of 0.2
percent is specified.

Proof Load: The point to which a material may be stressed without evidence of permanent deformation.

Hardness: The resistance of a material to plastic deformation. Usually measured in steels by the Brinell,
Rockwell, or Vickers indentation-hardness text methods.

302
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
FASTENER TECHNICAL DATA & CHARTS

Screw Threads

Thread forms: Screw threads are spiral grooves produced on the outside of a bolt (external threads) or TOOLS &
machined inside a nut (internal threads). Four thread forms have been established by the ANSI: UN (internal and ACCESSORIES
external threads). UNR (external threads only), UNK (external threads only), UNJ (internal and external threads).
CONTRACTOR
CUT VS. ROLL THREADS: The terms “rolled thread” and “cut thread” refer solely to the physical characteristics SUPPLIES
of commercial bolts or studs, not to the method of thread production. A cut-thread bolt has a shank diameter
equal to the threaded diameter; a rolled-thread bolt has a shank diameter less than the threaded diameter. hangers
& strut
CLASSES OF THREAD FIT: Classes of thread fit are distinguished from each other by the amounts of tolerance
specified. Classes 1A, 2A, and 3A apply to external threads; Classes 1B, 2B and 3B, to internal threads. fasteners &
threaded rod
Classes 1A and 1B are shown in ANSI standards but are rarely used. Most standard fasteners are
produced with a Class 2A fit for bolts and a Class 2B fit for nuts. The Class 2A allowance assures easier
assembly of mating parts, minimizes galling and seizing in high-cycle wrench assembly, and can be
used to accommodate commercial electroplated finishes. Classes 3A and 3B afford no allowance or
clearance for mating parts and are used chiefly for applications where a close tolerance fit is important.

Class 5 is a special interference fit which results in an actual overlap of dimensions when threaded parts are
fitted together. It is normally used only on the tap-end of studs.

Threading requirements are designated (1) by the number of threads per inch applied to a specific diameter;
(2) by the initial letters of the thread standard (UNR or UN); (3) by the letters C, F, or numeral 8 to indicate
coarse-, fine-, or 8-thread series; and (4) by the thread fit. The following example illustrates the method of
designating a screw thread:

1/2 in. -13 UNRC-2A concrete
where anchors

1/2 in. = nominal diameter of thread
13 = number of threads per inch

UNR = thread form standard (Unified National Radius-Root)
C = coarse-thread series

2A = class of thread fit

The coarse-thread series (UNRC or UNC) is used on the vast majority of bolts and nuts.Number of threads per specialty items
inch ranges from 20 threads for a 1/4-in.- diameter bolt to 4 threads for a 4-in.-diameter bolt. The fine-thread services & data
series (UNRF or UNF) is found mostly in automotive and aeronautical work. Threads per inch range from 28
threads for a 1/4-in.-diameter bolt to 12 threads for a 1-1/2-in.-diameter bolt. There is no fine-thread standard
for fasteners over 1-1/2 in.

The 8-thread series (8UNR or 8UN) is used only for sizes over 1 in. in diameter, usually in high-temperature,
high pressure service.

303
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
FASTENER TECHNICAL DATA & CHARTS

Identification Markings On Bolt Heads

TOOLS & ASTM and SAE Standards
ACCESSORIES Specifications - Proof Loads - Tensile Strengths

Proof Tensile

Grade Specification Material Bolt and Screw Load Strength

Marking Size Inches psi min psi

CONTRACTOR SAE-J429 Low or Medium 1/4 thru 1-1/2 33,000 60,000
SUPPLIES Grade 1 Carbon Steel

ASTM-A307 1/4 thru 4 60,000

SAE-J429 Low or Medium 1/4 thru 3/4 55,000 74,000
Grade-2 Carbon Steel 60,000
Over 3/4 thru 1-1/2 33,000

SAE-J429 1/4 thru 1 85,000 120,000
74,000 105,000
Grade 5 Medium Carbon Steel Over 1 thru 1-1/4

Quenched and 1/4 thru 1 85,000 120,000
Over 1 thru 1-1/2 74,000 105,000
ASTM-A449 Tempered Over 1-1/2 thru 3 55,000
90,000
hangers
& strut
* ASTM-A325 Medium Carbon Steel 1/2 thru 1-1/2 85,000 120,000
Quenched and Over 1 thru 1-1/2 74,000 105,000
Type 1 Tempered
1/2 thru 1 85,000 120,000
* ASTM-A325 Low Carbon Martensite
Type 2 Steel Quenched and
Tempered


fasteners & ASTM-A325 Weather Resistant Steel 1-1/8 thru 1-1/2 74,000 105,000
threaded rod Quenched and 1/2 thru 1 85,000 120,000
Type 3 Tempered



ASTM-A354 Low Alloy Steel 1/4 thru 2-1/2 80,000 105,000
Quenched and Over 2-1/4 thru 4 75,000 100,000
Grade BB
BB Tempered

ASTM-A354 Alloy Steel 1/4 thru 4 105,000 125,000
Quenched and
Grade BC Over 2-1/2 thru 4 95,000 115,000
Tempered
BC

concrete Medium Carbon
anchors Alloy Steel
SAE-J429
Quenched and
GRADE 8 Tempered

1/4 thru 1-1/2 120,000 150,000

ASTM-A354 Alloy Steel
Quenched and
Grade BD
Tempered


specialty items ASTM-A490 Alloy Steel 1/2 thru 1-1/2 120,000 150,000
services & data Quenched and
Type 1
Tempered


* Radial lines on Type 1 bolts are optional to manufacturer.
* On Type 2 bolts radial lines 60 degrees apart are required.
Bolt Head markings include manufacturers identity symbols.

304
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
FASTENER TECHNICAL DATA & CHARTS

Tightening Torque For Screws, Bolts & Nuts

TABLE I - TORQUE COEFFICIENTS - K TOOLS &
ACCESSORIES
Measured K (average)

Bolt Size Theoretical 1
K High-point torque Mid-point torque

1/4 -20 0.210 0.243 0.267 CONTRACTOR
1/4 -28 0.205 0.216 0.231 SUPPLIES
5/16 -18 0.210 0.206 0.186
5/16 -24 0.205 0.194 0.183

3/8 -16 0.204 0.200 0.247
3/8 -24 0.198 0.192 0.234
7/16 -14 0.205 0.217 0.224
7/16 -20 0.200 0.194 0.190

1/2 -13 0.201 0.205 0.158
1/2 -20 0.195 0.167 0.205
9/16 -12 0.198 0.194 0.214
9/16 -18 0.193 0.196 0.207

5/8 -11 0.199 0.178 0.196 hangers
5/8 -18 0.193 0.183 0.175 & strut
3/4 -10 0.194 0.169 0.172
3/4 -16 0.189 0.170 0.180

7/8 -  9 0.194 0.181 0.194
7/8 -14 0.189 0.171 0.178
1 -  8 0.193 0.188 0.204
1 -14 0.188 0.161 0.167

Average 0.198 0.191 0.201

NOTE: 1. Computed with coefficient of friction of 0.15 and the dimensions of American National Standard Hex Nut.

TABLE II - TORQUE COEFFICIENTS - COMPUTED fasteners &
threaded rod
Hex Cap Screw Heavy

Size Hex Nut (Finished Hex Bolt) Hex Screw

K1 K2 K3 K K K

1/4 -20 0.1055 0.0753 0.0318 0.213 0.213 0.223
1/4 -28 0.1055 0.0786 0.0227 0.207 0.207 0.218

5/16 -18 0.0993 0.0766 0.0284 0.204 0.204 0.213
5/16 -24 0.0993 0.0790 0.0212 0.200 0.200 0.208

3/8 -16 0.0950 0.0772 0.0265 0.199 0.199 0.213
3/8 -24 0.0950 0.0802 0.0176 0.193 0.193 0.207

7/16 -14 0.0980 0.0772 0.0260 0.201 0.196 0.207 concrete
7/16 -20 0.0980 0.0800 0.0181 0.196 0.190 0.202 anchors

1/2 -13 0.0950 0.0780 0.0245 0.198 0.198 0.208
1/2 -20 0.0950 0.0811 0.0159 0.192 0.192 0.203

9/16 -12 0.0970 0.0781 0.0235 0.199 0.195 0.202
9/16 -18 0.0970 0.0811 0.0157 0.194 0.191 0.197

5/8 -11 0.0950 0.0783 0.0231 0.196 0.196 0.205
5/8 -18 0.0950 0.0816 0.0141 0.191 0.191 0.199

3/4 -10 0.0950 0.0790 0.0212 0.195 0.195 0.203 specialty items
3/4 -16 0.0950 0.0819 0.0132 0.190 0.190 0.198 services & data

7/8- 9  0.0950 0.0793 0.0201 0.194 0.194 0.201
7/8 -14 0.0950 0.0819 0.0130 0.190 0.190 0.196

1 - 8  0.0950 0.0795 0.0199 0.194 0.194 0.200
1 -14 0.0950 0.0826 0.0109 0.189 0.189 0.194
Average 0.197 0.196 0.205

NOTE: K1 + K2 + K3 = K

305
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
FASTENER TECHNICAL DATA & CHARTS
TOOLS &
ACCESSORIES Cap Screws

SAE Standard J429 - Grades 2, 5 and 8

GRADE 2 GRADE 5 GRADE 8

CONTRACTOR
SUPPLIES

hangers Grade 2 Grade 5 Grade 8
& strut
Low-carbon bright Medium-carbon, heat treated Alloy, heat treated in a carbon
fasteners & 1/4 in. to 11/2 in. inclusive, in a carbon controlled at- controlled atmosphere, 1/4 in.
threaded rod with minimum tensile mosphere, 1/4 in. to 11/2 in., to 1 in., inclusive, with
strength of 74,000 psi in inclusive, with minimum minimum tensile strength of
diameters through 3/4 in. and tensile strength of 120,000 psi 150,000 psi.
60,000 psi for diameters over in diameters through 1 in. and
3/4 in. through 11/2 in. 105,000 psi for diameters over Grade 8 will also meet
1 in. through 11/2 in. ASTM specification A354
Warning to fine thread users! Grade BD.
Grade 2 is not recommended Grade 5 will also meet other
for use with fine threads. We specifications such as ASTM
suggest the use of Grade 5 A449.
because of superior resistance
concrete to stripping during tightening.
anchors Grade 2 may be used as an
alternate for ASTM A307
Grade A.

specialty items BE SURE TO VERIFY!
services & data
We will gladly provide specific product information
and certifications prior to your purchase.

306
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
FASTENER TECHNICAL DATA & CHARTS
TOOLS &
Bolts - Hex And Heavy Hex ACCESSORIES

ASTM A307 Grade A and B Mechanical Properties

SEE NOTE SEE NOTE CONTRACTOR
SUPPLIES
HEX BOLT HEAVY
HEX BOLT

Hex bolts are available in two dimensional standards: hangers
• The heavy hex bolt has a head dimension averaging approximately 1/8“ wider across the flats than & strut
the standard hex bolt.It is generally used for applications where maximum bearing area is required.
fasteners &
• Hex bolts are offered with UNRC-2A threads in diameters ranging from 1/4” through 2”. threaded rod
Heavy hex bolts with UNRC-2A threads are offered in diameters of 1/2” to 1-1/2” inclusive.
concrete
Hex bolts of heat treated carbon or alloy steel are available from cap-screw stock. anchors

Special Note:

Hex bolts in a size range from 1/4” thru 3/4” in diameter and in lengths 8”
and shorter are often shipped from Cap-screw stock at the Hex bolt price.

However, when ordered as hex bolts there is no guarantee
that they will meet all Cap-screw requirements.

DIMENSIONAL DATA FOR BOTH TYPES IS SHOWN ON NEXT PAGE

specialty items
services & data

307
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
FASTENER TECHNICAL DATA & CHARTS

Bolts - Hex and Heavy Hex

TOOLS & HF
ACCESSORIES
HEX HEAD CAP SCREWS E

+0° G
30° -15° L T (REF)*

Nominal E F G H LT (Ref)*
Size
Body Width Across Width Across Thread Length
or Basic
Screw Dia. Flats Corners Height For Screw For Screw
Dia. Lengths Lengths
CONTRACTOR Max. Min. Basic Max. Min. Max. Min. Basic Max. Min. ≤6 in. >6 in.
SUPPLIES 1/4
/ 5 16 0.2500 0.2450 /7 16 0.438 0.428 0.505 0.488 /5 32 0.163 0.150 Basic Basic
hangers / 3 8 0.3125 0.3065 1/2 0.500 0.489 0.577 0.557 /13 64 0.211 0.195
& strut / 7 16 0.3750 0.3690 /9 16 0.562 0.551 0.650 0.628 /15 64 0.243 0.226 0.750 1.000
/ 1 2 0.4375 0.4305 5/8 0.625 0.612 0.722 0.698 /9 32 0.291 0.272 0.875 1.125
/ 9 16 0.5000 0.4930 3/4 0.750 0.736 0.866 0.840 /5 16 0.323 0.302 1.000 1.250
/ 5 8 0.5625 0.5545 /13 16 0.812 0.798 0.938 0.910 /23 64 0.371 0.348 1.125 1.375
/ 3 4 0.6250 0.6170 /15 16 0.938 0.922 1.083 1.051 /25 64 0.403 0.378 1.250 1.500
/ 7 8 0.7500 0.7410 1 1/8 1.125 1.100 1.299 1.254 /15 32 0.483 0.455 1.375 1.625
1 0.8750 0.8660 1 /5 16 1.312 1.285 1.516 1.465 /35 64 0.563 0.531 1.500 1.750
1 1/8 1.0000 0.9900 1 1/2 1.500 1.469 1.732 1.675 /39 64 0.627 0.591 1.750 2.000
1 1/4 1.1250 1.1140 1 /11 16 1.688 1.631 1.949 1.859 /11 16 0.718 0.658 2.000 2.250
1 3/8 1.2500 1.2390 1 7/8 1.875 1.812 2.165 2.066 /25 32 0.813 0.749 2.250 2.500
1 1/2 1.3750 1.3630 2 /1 16 2.062 1.994 2.382 2.273 /27 32 0.878 0.810 2.500 2.750
1 3/4 1.5000 1.4880 2 1/4 2.250 2.175 2.598 2.480 /15 16 0.974 0.902 2.750 3.000
2 1.7500 1.7380 2 5/8 2.625 2.538 3.031 2.893 1 /3 32 1.134 1.054 3.000 3.250
2 1/4 2.0000 1.9880 3 3.000 2.900 3.464 3.306 1 /7 32 1.263 1.175 3.250 3.500
2 1/2 2.2500 2.2380 3 3/8 3.375 3.262 3.897 3.719 1 3/8 1.423 1.327 3.750 4.000
2.5000 2.4880 3 3/4 3.750 3.625 4.330 4.133 1 /17 32 1.583 1.479 4.250 4.500
2 3/4 2.7500 2.7380 4 1/8 4.125 3.988 4.763 4.546 1 /11 16 1.744 1.632 4.750 5.000
3 3.0000 2.9880 4 1/2 4.500 4.350 5.196 4.959 1 7/8 1.935 1.815 5.250 5.500
5.750 6.000
6.250 6.500

H
F

E

fasteners & HEX AND HEAVY HEX BOLTS G
threaded rod
+0° L T (REF)*
30° -15°

Nominal E F G H LT (Ref)*
Size
Body or Width Across Width Across Thread Length
or Basic Shoulder Dia. Flats
Bolt Corners Height For Bolt For Bolt
Dia. Max. Lengths Lengths
Basic Max. Min. Max. Min. Basic Max. Min. ≤6 in. >6 in.
1/4 0.260
/ 5 16 0.324 /11 64 0.188 0.150 Basic Basic
/ 3 8 0.388 /7 32 0.235 0.195
concrete / 7 16 0.452 /7 16 0.438 0.425 0.505 0.484 1/4 0.268 0.226 0.750 1.000
anchors / 1 2 0.515 1/2 0.500 0.484 0.577 0.552 /19 64 0.316 0.272 0.875 1.125
/ 5 8 0.642 /9 16 0.562 0.544 0.650 0.620 /11 32 0.364 0.302 1.000 1.250
specialty items / 3 4 0.768 5/8 0.625 0.603 0.722 0.687 /27 64 0.444 0.378 1.125 1.375
services & data / 7 8 0.895 3/4 0.750 0.725 0.866 0.826 1/2 0.542 0.455 1.250 1.500
1 1.022 /15 16 0.938 0.906 1.083 1.033 /37 64 0.604 0.531 1.500 1.750
1 1/8 1.149 1 1/8 1.125 1.088 1.299 1.240 /43 64 0.700 0.591 1.750 2.000
1 1/4 1.277 1 /5 16 1.312 1.269 1.516 1.447 3/4 0.780 0.658 2.000 2.250
1 3/8 1.404 1 1/2 1.500 1.450 1.732 1.653 /27 32 0.876 0.749 2.250 2.500
1 1/2 1.531 1 /11 16 1.688 1.631 1.949 1.859 /29 32 0.940 0.810 2.500 2.750
1 3/4 1.785 1 7/8 1.875 1.812 2.165 2.066 1 1.036 0.902 2.750 3.000
2 2.039 2 /1 16 2.062 1.994 2.382 2.273 1 /5 32 1.196 1.054 3.000 3.250
2 1/4 2.305 2 1/4 2.250 2.175 2.598 2.480 1 /11 32 1.388 1.175 3.250 3.500
2 1/2 2.559 2 5/8 2.625 2.538 3.031 2.893 1 1/2 1.548 1.327 3.750 4.000
2.827 3 3.000 2.900 3.464 3.306 1 /21 32 1.708 1.479 4.250 4.500
2 3/4 3.081 3 3/8 3.375 3.262 3.897 3.719 1 /13 16 1.869 1.632 4.750 5.000
3 3.335 3 3/4 3.750 3.625 4.330 4.133 2 2.060 1.815 5.250 5.500
3.589 4 1/8 4.125 3.988 4.763 4.546 2 /3 16 2.251 1.936 5.750 6.000
3 1/4 3.858 4 1/2 4.500 4.350 5.196 4.959 2 /5 16 2.380 2.057 6.250 6.500
3 1/2 4.111 4 7/8 4.875 4.712 5.629 5.372 2 1/2 2.572 2.241 6.750 7.000
3 3/4 5 1/4 5.250 5.075 6.062 5.786 2 /11 16 2.764 2.424 7.250 7.500
4 5 5/8 5.625 5.437 6.495 6.198 7.750 8.000
6 6.000 5.800 6.928 6.612 8.250 8.500

* BASIC THREAD LENGTH, LT, is a reference dimension, intended for calculation purposes only, which represents the distance

from the extreme end of the screw or bolt to the last complete (full form) thread.

308
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
FASTENER TECHNICAL DATA & CHARTS

Types of Studs

CONTINUOUS THREAD STUDS: Continuous-thread studs are threaded from T ype 1 TOOLS &
Type 2 ACCESSORIES
end to end and are often used for flange bolting with two nuts applied.
CONTRACTOR
Type 1 — General purpose. The length of this type is measured from end to end. Threads SUPPLIES
are UNRC-2A.

Type 2 — Studs for temperature-pressure piping. These studs are made to the dimensional
standard requirements of ANSI B16.5 and have a length measurement
requirement different from all other studs, i.e., the length is measured from
firstthread to first thread, exclusive of points. Points are flat and chamfered.
Threads are UNRC-2A for all sizes 1 in. and under and 8UNR-2A for all sizes

over 1 in.

TAP-END STUDS: Tap-end studs have a short thread on one end, called the tap hangers
& strut
end which is threaded to a Class NC5 or Class UNRC-3A fit. This end is for screwing
into a tapped hole. The other or nut end is threaded with a Class UNRC-2A fit. Length fasteners &
of the stud is measured overall. The tap end has a chamfered point, but the nut end threaded rod
may have either a chamfered or round point, at the manufacturer’s option. Tap-end
studs are available in four types, as follows:

Type 1 — Unfinished, have a full diameter but no standard body tolerances.
Type 2 — Finished, having either an undersize body with rolled threads or a full-size body with cut threads, at the manufacturer’s

option. The body portion will be finished to a minimum Class 2A pitch diameter or maximum basic major diameter
of the nut-end thread.
Type 3 — Finished full-body, having tolerances equal to that on major diameter of Class 2A threads.
Type 4 — Finished close-body, milled or ground to tolerances specified by the user.

DOUBLE-END STUDS: Double-end studs have equal-length threads on each end concrete
anchors
to accommodate a nut and are threaded to a Class 2A fit. Length of stud is measured
overall. Both ends have chamfered points, but round points may be furnished on either
or both ends at the manufacturer’s option. This style is furnished in the same four types
listed for tap-end studs. Double-end studs are used for flange bolting or other applications
where torquing from both ends is necessary or desirable.

Most steel grades not heat treated or quenched and tempered can be furnished on special order for production quantities. Only
the Type 2 continuous thread studs made to specification ASTM A193 grade B7 are stocked in a full range of sizes. Page 155
lists all the commonly available grades of Alloy steel quenched and tempered studs.

Tap end and double end studs are not available from stock - They are available only on special order.

specialty items
services & data

309
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
FASTENER TECHNICAL DATA & CHARTS

Heat Treated Alloy Studs, Bolts and Threaded Bars

TOOLS & Commonly used are the following grades of heat-treated alloy steel for high-pressure or extreme temperature service in diameters
ACCESSORIES of 1/2 in. to 2 in., inclusive. Other grades and other diameters are available on special order.

CONTRACTOR ASTM A354 - Grades BC and BD
SUPPLIES
Heat treated alloy steels for applications at normal atmospheric temperatures where high strength is required.
hangers
& strut ASTM A193 - Grade B7

A heat treated chromium-molybdenum steel widely used for medium high-temperature service.

ASTM A193 - Grade B16

A heat treated chromium-molybdenum-vanadium steel widely used for high-temperature service.

ASTM A320 - Grade L7

This grade is intended for low-temperature service down to minus 150° F and has a minimum Charpy impact value
of 15 ft-lb at this temperature. Sizes 2-1/2 in. and under.

ASTM A320 - Grade L43

The same properties offered by Grade L7 in sizes up to 2-1/2 in. are obtainable up to 4 in. in Grade L43.

Heat-treated alloy steel bolts and threaded bars are also available in the grades listed above - bolts in diameters
of 3/8 in. to 1-1/4 in., inclusive; bars in diameters of 1/2 in. to 2 in., inclusive. These are available only on special order.

Chemical Composition Tensile Requirements
heat-treated, alloy steel studs heat-treated, alloy steel studs

A354 Grades BC, BD A193 Grade B7      Elon- Reduc-
+ See note below Chromium Molybdenum Min. Tensile Yield gation tion
(AISI 4140, 4142, 4145) tempering strength point in 2 in. of area
Grade Diameter, in. temp F min psi min psi min pct min pct
Check Check
Range variation Range variation
Elements percent over percent Over or under A354 Grade BC 2-1/2 and under 850 125,000 109,000 16 50
fasteners & percent percent Over 2-1/2 to 4 incl 850 115,000   99,000 16 45
threaded rod A354 Grade BD 1-1/2 and under 850 150,000 125,000 14 35
Carbon — — •0.38- 0.48 0.02 A193 Grade B7 2-1/2 and under 1100 125,000 105,000 16 50
Manganese — — 0.75-1.00 0.04  Chromium Over 2-1/2 to 4 incl 1100 115,000   95,000 16 50
Phosphorus, max 0.04 0.005 0.005 over  Molybdenum Over 4 to 7 incl 1100 100,000   75,000 18 50
Sulphur, max 0.04 0.005 0.04 0.005 over A193 Grade B16 2-1/2 and under
Silicon — — 0.04 0.02  Chromium Over 2-1/2 to 4 incl 1200 125,000 105,000 18 50
Chromium — — 0.20- 0.35 0.05  Molybdenum Over 4 to 7 incl 1200 110,000   95,000 17 45
Molybdenum — — 0.80-1.10 0.02  Vanadium 1200 100,000   85,000 16 45
0.15-0.25 A320 Grade L7 2-1/2 and under — 125,000 105,000 16 50
 Chromium
A193 Grade B16,  Molybdenum 4 and under
Chromium, Molybdenum, A320 Grade L43
 Nickel
Vanadium  Chromium
 Molybdenum
Check — 125,000 105,000 16 50
Range variation
Elements percent Over or under
percent

Carbon 0.36-0.44 0.02
Manganese 0.45-0.70 0.03
concrete Phosphorus, max 0.04 0.005 over
anchors Sulphur, max 0.04 0.005 over
Silicon 0.20-0.35 0.02
Chromium 0.80-1.15 0.05 Not sure?
Molybdenum 0.50-0.65 0.03
Vanadium 0.25-0.35 0.03 We’re happy to provide you with
Complete Product Literature
A320 Grade L7 A320 Grade L43 and detailed specifications.
Chromium-Molybdenum Nickel-Chromium
(AISI 4140, 4142, 4145) Molybdenum (AISI 4340) Just ask us!

Check Check
Range variation Range variation
Elements percent over or under percent Over or under
specialty items percent percent
services & data
Carbon •0.38-0.48 0.02 0.38-0.43 0.02
Manganese 0.75-1.00 0.04 0.60-0.85 0.03
Phosphorus, max 0.005 over 0.005 over
Sulphur, max 0.04 0.005 over 0.04 0.005 over
Silicon 0.04 0.02 0.04 0.02
Nickel 0.20-0.35 — 0.20-0.35 0.05
Chromium — 0.05 1.65-2.00 0.03
Molybdenum 0.80-1.10 0.02 0.70-0.90 0.02
0.15-0.25 0.20-0.30

• For bar sizes over 3-1/2 in. to 4 in., inclusive, the carbon content may be 0.50 pct max
+ Any alloy steel capable of meeting the tensile requirements of Specification A354 may be used

310
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
FASTENER TECHNICAL DATA & CHARTS
TOOLS &
Nuts for High-Temperature, High Pressure Service ACCESSORIES

ASTM A194 - Grade 2, 2H, 4 and 7AN Standard B18.2.2 CONTRACTOR
SUPPLIES
For high-temperature, high-pressure in combination with alloy studs and bolts.
These nuts are tapped UNC-2B in sizes of 1 in. and under or 8UN-2B over 1 in.

ASTM A194 - GRADE 2

Treated nuts suitable for moderate temperature and pressure conditions.

ASTM A194 - GRADE 2H

Quenched nuts suitable for high-temperature and high-pressure conditions.

ASTM A194 - GRADES 4 and 7

Heat-treated carbon-molybdenum and chromium
molybdenum steel nuts suitable for severe temperature and pressure conditions.

Grade 2 Grade 2H Grade 4 Grade 7 hangers
ASTM A194 ASTM A194 ASTM A194 ASTM A194 & strut

Chemical Composition fasteners &
threaded rod
Grade C Mn P S Si M0 Cr
—
2 and 2H 0.40min — 0.04 max 0.05 max — —
—
4 0.40 0.70 0.20 0.20
to 0.50 to 0.90 0.035 max 0.04 max to 0.35 to 0.30 0.80
to 1.10
7 0.38 0.75 0.20 0.15
to 0.48 to 0.35 to 0.25
to 1.00 0.04 max 0.04 max

Hardness Requirements concrete
anchors
Grade Brinell Rockwell B Rockwell C
2
2H 159 to 352 84 min. —
4 and 7
248 to 352 — 24 to 38

248 to 352 — 24 to 38

if you can’t find the fastener your looking for... specialty items
services & data
Call us - It may be in stock or we can order it for you!

311
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
FASTENER TECHNICAL DATA & CHARTS

TOOLS & Nuts - Hex and Heavy Hex
ACCESSORIES
ASTM A563 GRADE A

Dimensions

Hex nuts are available in diameters ranging from 1/4 in. to 2 in. Double chamfered through the 1 in. size, and washer faced in sizes
over 1 in. Heavy hex nuts are available from 1/4 in. to 4 in., washer faced in the full range of sizes, as well as double chamfered in
sizes through 1 in.

CONTRACTOR HEX NUTS HEAVY HEX NUTS
SUPPLIES WASHER FACED WASHER FACED

AND AND
DOUBLE DOUBLE
CHAMFERED CHAMFERED

HEX NUTS DIMENSIONS (in.) ANSI B18.22

Nominal Size F - Width G - Width H - Thickness
or Basic Major Across Flats Across Corners Heavy Hex Nuts
Di a. of Thread
Basic Max. Min. Max. Min. Basic Max. Min.

hangers / 1 4 0.2500 /7 16 0.438 0.428 0.505 0.488 /7 32 0.226 0.212
& strut / 5 16 0.3125 1/2 0.500 0.489 0.577 0.557 /17 64 0.273 0.258
/ 3 8 0.3750 /9 16 0.562 0.551 0.650 0.628 /21 64 0.337 0.320
fasteners & / 7 16 0.4375 /11 16 0.688 0.675 0.794 0.768 3/8 0.385 0.365
threaded rod / 1 2 0.5000 3/4 0.750 0.736 0.866 0.840 /7 16 0.448 0.427
/ 9 16 0.5625 7/8 0.875 0.861 1.010 0.982 /31 64 0.496 0.473
/ 5 8 0.6250 /15 16 0.938 0.922 1.083 1.051 /35 64 0.559 0.535
/ 3 4 0.7500 1 1/8 1.125 1.088 1.299 1.240 /41 64 0.665 0.617
/ 7 8 0.8750 1 /5 16 1.312 1.269 1.516 1.447 3/4 0.776 0.724
1 1.0000 1 1/2 1.500 1.450 1.732 1.653 /55 64 0.887 0.831
1 1/8 1.1250 1 /11 16 1.688 1.631 1.949 1.859 /31 32 0.999 0.939
1 1/4 1.2500 1 7/8 1.875 1.812 2.165 2.066 1 /1 16 1.094 1.030
1 3/8 1.3750 2 /1 16 2.062 1.994 2.382 2.273 1 /11 64 1.206 1.138
1 1/2 1.5000 2 1/4 2.250 2.175 2.598 2.480 1 /9 32 1.317 1.245
1 3/4 1.7500 2 5/8 2.625 2.538 3.031 2.883 1 1/2 1.540 1.460
2     2.0000 3 3.000 2.900 3.464 3.306 1 /23 32 1.763 1.675

HEAVY HEX NUTS DIMENSIONS (in.) ANSI B18.22

Nominal Size F - Width G - Width H - Thickness
or Basic Major Across Flats Across Corners Heavy Hex Nuts
Di a. of Thread
Basic Max. Min. Max. Min. Basic Max. Min.

concrete / 1 4 0.2500 1/2 0.500 0.488 0.577 0.556 /15 64 0.250 0.218
anchors / 5 16 0.3125 /9 16 0.562 0.546 0.650 0.622 /19 64 0.314 0.280
/ 3 8 0.3750 /11 16 0.688 0.669 0.794 0.763 /23 64 0.377 0.341
specialty items / 7 16 0.4375 3/4 0.750 0.728 0.866 0.830 /27 64 0.441 0.403
services & data / 1 2 0.5000 7/8 0.875 0.850 1.010 0.969 /31 64 0.504 0.464
/ 9 16 0.5625 /15 16 0.938 0.909 1.083 1.037 /35 64 0.568 0.526
/ 5 8 0.6250 1 /1 16 1.062 1.031 1.227 1.175 /39 64 0.631 0.587
/ 3 4 0.7500 1 1/4 1.250 1.212 1.443 1.382 /47 64 0.758 0.710
/ 7 8 0.8750 1 /7 16 1.438 1.394 1.660 1.589 /55 64 0.885 0.833
1 1.0000 1 5/8 1.625 1.575 1.876 1.796 /63 64 1.012 0.956
1 1/8 1.1250 1 /13 16 1.812 1.756 2.093 2.002 1 /7 64 1.139 1.079
1 1/4 1.2500 2 2.000 1.938 2.309 2.209 1 /7 32 1.251 1.187
1 3/8 1.3750 2 /3 16 2.188 2.119 2.526 2.416 1 /11 32 1.378 1.310
1 1/2 1.5000 2 3/8 2.375 2.300 2.742 2.622 1 /15 32 1.505 1.433
1 5/8 1.6250 2 /9 16 2.562 2.481 2.959 2.828 1 /19 32 1.632 1.556
1 3/4 1.7500 2 3/4 2.750 2.662 3.175 3.035 1 /23 32 1.759 1.679
1 7/8 1.8750 2 /15 16 2.938 2.844 3.392 3.242 1 /27 32 1.886 1.802
2 2.0000 3 1/8 3.125 3.025 3.608 3.449 1 /31 32 2.013 1.925
2 1/4 2.2500 3 1/2 3.500 3.388 4.041 3.862 2 /13 64 2.251 2.155
2 1/2 2.5000 3 7/8 3.875 3.750 4.474 4.275 2 /29 64 2.505 2.401
2 3/4 2.7500 4 1/4 4.250 4.112 4.907 4.688 2 /45 64 2.759 2.647
3 3.0000 4 5/8 4.625 4.475 5.340 5.102 2 /61 64 3.013 2.893
3 1/4 3.2500 5 5.000 4.838 5.774 5.515 3 /3 16 3.252 3.124
3 1/2 3.5000 5 3/8 5.375 5.200 6.207 5.928 3 /7 16 3.506 3.370
3 3/4 3.7500 5 3/4 5.750 5.562 6.640 6.341 3 /11 16 3.760 3.616
4 4.0000 6 1/8 6.125 5.925 7.073 6.755 3 /15 16 4.014 3.862

312
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
FASTENER TECHNICAL DATA & CHARTS

Washers and Split Lockwashers

SAE USS STANDARD TOOLS &
ACCESSORIES
Bolt Inches Thick- Est. Pcs. Bolt Inches Thick- Est. Pcs.
Size I.D. O.D. ness Per 1 Lb. Size I.D. O.D. ness Per 1 Lb.
#4 3/16
#6 1/8 5/16 #21 (1/32) 1650 1/4 1/4 9/16 #18 (3/64) 361
#8 5/16
#10 5/32 3/8 #18 (3/64) 790 3/8 5/16 3/4 #16 (1/16) 149
#12 7/16
1/4 3/16 7/16 #18 (3/64) 585 1/2 3/8 7/8 #14 (5/64) 87
5/16 9/16
3/8 7/32 1/2 #18 (3/64) 435 5/8 7/16 1 #14 (5/64) 67
7/16 3/4
1/2 1/4 9/16 #16 (1/16) 280 7/8 1/2 1-1/4 #14 (5/64) 41
9/16 1
5/8 9/32 5/8 #16 (1/16) 222 1-1/8 9/16 1-3/8 #12 (7/64) 26 CONTRACTOR
3/4 1-1/4 SUPPLIES
7/8 11/32 11/16 #16 (1/16) 192 S.A.E. washers are of smaller 1-3/8 5/8 1-1/2 #12 (7/64) 22
1 O.D. and thinner gauges than 1-1/2
1-1/8 13/32 13/16 #16 (1/16) 140 their counterpart bolt sizes of 1-5/8 11/16 1-3/4 #10 (9/64) 13
1-1/4 1-3/4
1-3/8 15/32 59/64 #16 (1/16) 105 U.S. Standard washers. 1-7/8 13/16 2 #9 (5/32) 9.1
1-1/2 USS washers were developed 2
17/32 1-1/16 #13 (3/32) 55 to requirements in the majority 2-1/4 15/16 2-1/4 #8 (11/64) 6.5
of industrial applications in
19/32 1-3/16 #13 (3/32) 43 1-1/16 2-1/2 #8 (11/64) 5.3
all fields of manufacturing,
21/32 1-5/16 #13 (3/32) 36 maintenance and repair. 1-1/4 2-3/4 #8 (11/64) 4.5

13/16 1-1/2 #10 (9/64) 21 The O.D., I.D. and thickness 1-3/8 3 #8 (11/64) 3.8
specifications meet the
15/16 1-3/4 #10 (9/64) 16 optimum of applications. 1-1/2 3-1/4 #7 (3/16) 3

1-1/16 2 #10 (9/64) 12 1-5/8 3-1/2 #7 (3/16) 2.6

1-3/16 2-1/4 #10 (9/64) 9.2 1-3/4 3-3/4 #7 (3/16) 2.3 hangers
& strut
1-5/16 2-1/2 #9   (5/32) 6.3 1-7/8 4 #7 (3/16) 2

1-7/16 2-3/4 #9   (5/32) 5.25 2 4-1/4 #7 (3/16) 1.8

1-9/16 3 #9   (5/32) 4.25 2-1/8 4-1/2 #7 (3/16) 1.6

2-3/8 4-3/4 #5 (7/32) 1.2

MEDIUM SPLIT T2 t T
HELICAL SPRING LOCKWASHERS W
fasteners &
Nominal A B W T2 t - 2 threaded rod

WSaiszheer MDin. IianmsideMete r ax. ODMiaumatsxei.dt2ee r MWiidntW.h asher TSMectiohnickinn.ess

2 0.086 0.088 0.094 0.172 0.035 0.020

4 0.112 0.115 0.121 0.209 0.040 0.025

5 0.125 0.128 0.134 0.236 0.047 0.031

6 0.138 0.041 0.148 0.250 0.047 0.031

8 0.164 0.168 0.175 0.293 0.055 0.040

10 0.190 0.194 0.202 0.334 0.062 0.047 concrete
anchors
12 0.216 0.221 0.229 0.377 0.070 0.056

/ 1 4 0.250 0.255 0.263 0.489 0.109 0.062

/ 5 16 0.312 0.318 0.328 0.586 0.125 0.078

/ 3 8 0.375 0.382 0.393 0.683 0.141 0.094

/7 16 0.438 0.446 0.459 0.779 0.156 0.109

/ 1 2 0.500 0.509 0.523 0.873 0.171 0.125

/ 9 16 0.562 0.572 0.587 0.971 0.188 0.141

5/8 0.625 0.636 0.653 1.079 0.203 0.156

/ 3 4 0.750 0.763 0.783 1.271 0.234 0.188 specialty items
services & data
/ 7 8 0.875 0.890 0.912 1.464 0.266 0.219

1 1.000 1.017 1.042 1.661 0.297 0.250

1 1/16 1.062 1.080 1.107 1.756 0.312 0.266

1 1/8 1.125 1.144 1.172 1.853 0.328 0.281

1 3/16 1.188 1.208 1.237 1.950 0.344 0.297

1 1/4 1.250 1.271 1.302 2.045 0.359 0.312

1 1/2 1.500 1.525 1.561 2.430 0.422 0.375

313
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
DRYWALL AND CONSTRUCTION FASTENERS

TOOLS & PHILLIPS BUGLE HEAD FINE THREAD - BLACK PHOSPHATE
ACCESSORIES
Part Carton Carton Drive
Quantity Weight Size
Number Size 10 M 32 Ibs. # 2 Phillips Application
10 M 35 Ibs. # 2 Phillips Original and primary application of
SS 100 B # 6 x 1” 8 M 31 Ibs. # 2 Phillips D/W to 20-25 gauge metal studs.
5 M 25 Ibs. # 2 Phillips Also known as “all-purpose” screws.
SS 118 B # 6 x 1-1/8” 3.5 M 20 Ibs. # 2 Phillips
3 M 22 Ibs. # 2 Phillips Extra length allows user to attach
SS 114 B # 6 x 1-1/4” D/W to 20-25 gauge metal stud
2.5 M 21 Ibs. # 2 Phillips used in “scab over” applications.
SS 158 # 6 x 1-5/8” 2 M 24 Ibs. # 2 Phillips

SS 200 B # 6 x 2” 1 M 23 Ibs. # 2 Phillips
1 M 23 Ibs. # 2 Phillips
CONTRACTOR SS 214 # 6 x 2-1/4” 1 M 24 Ibs. # 2 Phillips
SUPPLIES


SS 212 B # 8 x 2-1/2”

SS 300 # 8 x 3”



SS 312 # 10 x 3-1/2”

SS 334 # 10 x 3-3/4”

SS 400 # 10 x 4”

PHILLIPS BUGLE HEAD COARSE THREAD - BLACK PHOSPHATE

hangers Part Carton Carton Drive
& strut Quantity Weight Size
Number Size Application
10 M 32 Ibs. # 2 Phillips
C 100 B # 6 x 1” 8 M 31 Ibs. # 2 Phillips Original and primary application
5 M 25 Ibs. # 2 Phillips of D/W to wood studs.
C 114 B # 6 x 1-1/4” 3.5 M 20 Ibs. # 2 Phillips
3 M 22 Ibs. # 2 Phillips Also used in many interior wood
C 158 B # 6 x 1 -5/8” 2.5 M 21 Ibs. # 2 Phillips and fixture fastening applications.
2 M 24 Ibs. # 2 Phillips
C 200 B # 6 x 2” 1.5 M 27.5 lbs. # 2 Phillips

C 214 B # 6 x 2-1/4”

fasteners & C 212 B # 8 x 2-1/2”
threaded rod
C 300 B # 8 x 3”

C 312 B # 10 x 3-1/2”

PHILLIPS BUGLE HEAD LAMINATOR - BLACK PHOSPHATE

Part Carton Carton Drive
Quantity Weight Size
Number Size Application

L 112 # 10 x 1-1/2” 5 M 39 Ibs. # 2 Phillips Temporary fastening of D/W to
D/W in doublewall requirements.


concrete PHILLIPS PAN HEAD FRAMER - BLACK PHOSPHATE
anchors
Part Carton Carton Drive
Quantity Weight Size
Number Size Application

SS 7716 X # 7 x 7/16” 15 M 40 Ibs. # 2 Phillips Light gauge metal stud &
track framing.


specialty items PHILLIPS TRIM HEAD “S” POINT - BLACK PHOSPHATE
services & data
Part Carton Carton Drive
Quantity Weight Size
Number Size Application
5 M 24 Ibs. # 1 Phillips
TH 158 T # 6 x 1-5/8” 3 M 21 Ibs. # 1 Phillips Finish screw for fastening of base
TH 214 T # 6 x 2-1/4” 2 M 23 Ibs. # 2 Phillips or trim through D/W to light
TH 300 T # 8 x 3” gauge metal studs.

314
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
DRYWALL AND CONSTRUCTION FASTENERS

SQUARE DRIVE TRIM HEAD - BLACK PHOSPHATE TOOLS &
ACCESSORIES


Part Carton Carton Drive
Quantity Weight Size
Number Size Application

THS 158 # 6 x 1-5/8” 5 M 24 Ibs. # 1 Robertson SQ Finish screw for fastening of base of trim
through D/W to light gauge metal studs.
THS 214 # 6 x 2-1/4” 3 M 21 Ibs. # 1 Robertson SQ



THS 300 # 8 x 3” 2 M 23 Ibs. # 2 Robertson SQ

MODIFIED TRUSS HEAD - BLACK PHOSPHATE OR ZINC PLATED CONTRACTOR
SUPPLIES
Part Carton Carton Drive
Quantity Weight Size
Number Size Application
10 M 35 Ibs. # 2 Phillips
W 916 Z # 8 x 9/16” 5 M 28 Ibs. # 2 Phillips For the application of metal lathe to light
W 100 Z # 8 x 1 “ 5 M 34 Ibs. # 2 Phillips 20-25 gauge metal studs. Recommended
W 114 Z # 8 x 1-1/4”
drive speed is 2500 rpm.

PHILLIPS BUGLE HEAD - LONG LIFE COATING hangers
& strut
Part Carton Carton Drive
Quantity Weight Size
Number Size Application

C 114 D # 6 x 1-1/4” 8 M 31 Ibs. # 2 Phillips For any exterior fastening including:
decks, fences, shade structures,
C 158 D # 6 x 1-5/8” 5 M 25 Ibs. # 2 Phillips Recommended for use in treated
yellow pine.
C 200 D # 6 x 2” 3.5 M 23 Ibs. # 2 Phillips

C 214 D # 6 x 2-1/4” 3 M 22 Ibs. # 2 Phillips

fasteners &
threaded rod
C 250 D # 8 x 2-1/2” 2.5 M 24 Ibs. # 2 Phillips

C 300 D # 8 x 3” 2 M 25 Ibs. # 2 Phillips



C 312 D # 10 x 3-1/2” 1 M 23 Ibs. # 2 Phillips

C 400 D # 10 x 4” 1 M 25 Ibs. # 2 Phiilips

SELF PIERCING SCREWS
HEX WASHER HEAD - ZINC COATING

Part Carton Carton Drive
Quantity Weight Size
Number Size Application concrete
10 M 31 Ibs. 1/4” Hex anchors
812 HWHSMS # 8 x 1/2” 10 M 38 Ibs. 1/4” Hex For H.V.A.C. or other thin gauge metals.
8 M 38 Ibs. 1/4” Hex Screws have a needle point for self piercing
834 HWHSMS # 8 x 3/4” 8 M 33 Ibs. 5/16” Hex
6 M 32 Ibs. 5/16” Hex piercing of sheet metal in a range of
8100 HWHSMS # 8 x 1” 6 M 34 lbs. 5/16” Hex 20 - 26 gauge.

1012 HWHSMS # 10 x 1/2”

1034 HWHSMS # 10 x 3/4”

10100 HWHSMS # 10 x 1”

PHILLIPS Part No. Size Pkg. Case SELF DRILLING METAL specialty items
Bugle 100 8000 FRAMING SCREWS services & data
Head SD1142* #6 X 1 1/4” 500 5000
SD1582* #6 X 1 5/8” 500 4000 • Pan Head • Zinc Plated
• Zinc Plated SD1782* #6 X 1 7/8” 250 3000
SD2382* #6 X 2 3/8” 250 2000 Part No. Size Pkg. Case
SD2582* #6 X 2 5/8” 250 2000 100 15,000

SD3002* #6 X 3” SD7716X* #7 X 7/16”


315
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
TEKS® SELF-DRILLING FASTENERS

TOOLS & Part Head Drill Drill & Tap Max. Material
ACCESSORIES Style Point Capacity Attachments
Number Description Applications
• HVAC, electrical trim
1208200 6-20 x 3/8” Pan #2 .036-.100 .100
1210200 8-18 x 1/2” Pan #2 .036-.100 .205 accessories to steel framing.
1213200 8-18 x 3/4” Pan #2 .036-.100 .455 • Residential steel frame
1218200 8-18 x 1” Pan #2 .036-.100 .705
1196200 8-18 x 1/2” HWH #2 .036-.100 .205 construction.
1199200 8-18 x 5/8” HWH #2 .036-.100 .330 • Track to stud.
1200200 8-18 x 3/4” HWH #2 .036-.100 .455 • Hat channel to stud.
1202200 8-18 x 1” HWH #2 .036-.100 .705 • Stud splicing.
1204200 8-18 x 1-1/2” HWH #2 .036-.100 1.205 
• Stitching roof deck, wall
CONTRACTOR 1107000 10-16 x 3/4” HWH #1 .018-.095 .220 panel sidelaps or duct work.
SUPPLIES 1109000 12-14 x 3/4” HWH #1 .018-.095 .205
1399000 1/4-14 x 7/8” HWH #1 .018-.095 .380 • Clips, duct straps, brick ties
or accessories to framing.
hangers 1398000 10-16 x 1/2” Pan #3 .036-.175 .150
& strut 1541000 10-16 x 5/8” Pan #3 .036-.175 .200 • Vibration Resistance;
1224000 10-16 x 3/4” Pan #3 .036-.175 .325 HVAC Applications
1542000 10-16 x 3/4” Oval #3 .036-.175 .325
1397000 10-16 x 1/2” HWH #3 .036-.175 .150
1127000 10-16 x 5/8” HWH #3 .036-.175 .200
1128000 *10-16 x 3/4” HWH #3 .036-.175 .325
1129000 10-16 x 1” HWH #3 .036-.175 .575
1544000 10-16 x 1” Oval #3 .036-.175 .575
1544000 10-16 x 1” Pan #3 .036-.175 .575
1130000 10-16 x 1-1/4” HWH #3 .036-.175 .825
1546000 10-16 x 1-1/4” Oval #3 .036-.175 .825
1131000 *10-16 x 1-1/2” HWH #3 .036-.175 1.075
1550000 10-24 x 3/4” HWH #3 .036-.175 .323
1551000 10-24 x 1” HWH #3 .036-.175 .575

†1786200 10-24 x 5/8” **HWH #2 .036-.175 .200

†1707200 10-16 x 3/4” **HWH #3 .036-.175 .323

†1821200 10-16 x 3/4” **HWH #3 .036-.175 .323

*  Available with Bonded Washer ** With serrations under head ††Electro-zinc finish

Part Head Drill Drill & Tap Max. Material
Style Point Capacity Attachments
Number Description Applications
#3 .036-.210 .270 • Roof deck to steel framing.
fasteners & 1134000 12-14 x 3/4’’ HWH #3 .036-.210 .520 • Wall panel to girt.
threaded rod 1136000 12-14 x 1” HWH #2 .036-.210 .550 • Duct work to steel framing.
1120000 12-14 x 1-1/4” HWH #2 .036-.210 .800 • Accessories to steel framing.
1123000 12-14 x 1-1/2” HWH #3 .036-.210 1.450 • Clip to steel framing.
1140000 12-14 x 2” HWH #3 .036-2.10 1.950 • Retrofit framing.
1553000 12-14 x 2-1/2 HWH #3 .036-.210 2.450 
1143000 12-14 x 3” HWH #3 .036-.210 3.450 
1146000 12-14 x 4” HWH
#3 .036-.210 .210
1147000 1/4-14 x 3/4” HWH #3 .036-.210 .400
#3 .036-.210 .650
1149000 1/4-14 x 1” HWH #3 .036-.210 .900
#3 .036-.210 1.400 
1150000 1/4-14 x 1-1/4” HWH #3 .036-.210 1.900
#3 .036-.210 2.460 
1152000 1/4-14 x 1-1/2” HWH #3 .036-.210 3.460 

1155000 1/4-14 x 2” HWH

1554000 1/4-14 x 2-1/2” HWH

1157000 1/4-14 x 3” HWH

1304000 1/4-14 x 4” HWH

concrete  All available with bonded washer.
anchors
1586000 1/4-14 x 3/4” *HWH #3 .036-.210 .250  • Commercial overhead
*HWH #3 .036-.210 .500  steel doors, hinges & latches
1587000 1/4-14 x 1”

* With serrations under head.

Part Drill Drill & Tap Max. Material
Style Attachments
Number Description Point Capacity Applications
.325
1088000 12-24 x 7/8” HWH #4 .125-.250 • Metal deck, clips,  
.575 liner panels or
specialty items 1414000 12-24 x 1-1/4” HWH #4.5 .125-.375 accessories to  
services & data .375 structural steel or  
1006000 12-24 x 1-1/4” HWH #5 .125-.500 .625 bar joist.
#5 .125-.500 1.125
1070000 12-24 x 1-1/2” HWH #5 .125-.500 2.150 • Longer fasteners can be
#5 .125-.500 3.150 used in retrofit clip and
1072000 12-24 x 2” HWH #5 .125-.500 4.150 sheet applications.
#5 .125-.500 5.150
1074000 12-24 x 3” *HWH #5 .125-.500 7.150
#5 .125-.500
1075000 12-24 x 4” *HWH

1641000 1/4-28 x 5” HWH

1431000 1/4-28 x 6” HWH

1590000 1/4-28 x 8” HWH

 All available with bonded washer.

* 5/16” Across flats HWH

316

THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
SELF-DRILLING FASTENERS

SELF-DRILLING FASTENERS W/ 9/16” BONDED WASHER TOOLS &
ACCESSORIES
Part Head Drill Drill & Tap Max. Material

Number Description Style Point Capacity Attachment Applications

1005000 10-16 x 3/4” HWH #3 .036-.175 .205
1308000 10-16 x 1-1/2” HWH #3 .036-.175 .955 • Brick tie to steel framing.

1011000 12-14 x 1” HWH #3 .036-.210 .400 • Mansard panel to steel fram- CONTRACTOR
1014000 12-14 x 1-1/4” HWH #2 .036-.210 .430 ing. SUPPLIES
1404000 12-14 x 1-1/2” HWH #2 .036-.210 .680
1009000 12-14 x 3/4” HWH #3 .036-.210 .150 • Roof panel to purlin.

1016000 12-14 x 2” HWH #3 .036-.210 1.330 • Wall panel to girt.
1333000 12-14 x 3” HWH #3 .036-.210 2.330 • Stitch roof and wall panels.
1332000 12-14 x 4” HWH #3 .036-.210 3.330

1416000 1/4-14 x 7/8” HWH #1 .024-.095 .260 • Retrofit panels to structural.

1019000 1/4-14 x 1-1/4” HWH #3 .036-.210 .780

1020000 1/4-14 x 1-1/2” HWH #3 .036-.210 1.280

1021000 1/4-14 x 2” HWH #3 .036-.210 1.340

1022000 1/4-14 x 3” HWH #3 .036-.210 2.340

1429000 1/4-14 x 4” HWH #3 .036-.210 3.340

1010000 12-24 x 7/8” HWH #4 .125-.250 .200 • Roof and wall panel to bar hangers
1415000 12-24 x 1-1/4” HWH #4.5 .125-.375 .450 joist or structural. & strut

1000000 12-24 x 1-1/4” HWH #5 .250-.500 .250 • Longer fasteners may be used
1001000 12-24 x 1-1/2” HWH #5 .250-.500 .500 in retrofit applications.
1002000 12-24 x 2” HWH #5 .250-.500 1.000

1003000 12-24 x 3” HWH #5 .250-.500 2.100

1004000 12-24 x 4” HWH #5 .250-.500 3.100

1647000* 1/4-28 x 5” HWH* #5 .250-.500 4.100

1642000** 1/4-28 x 5” HWH** #5 .250-.500 4.100

1432000* 1/4-28 x 6” HWH* #5 .250-.500 5.100

1619000* 1/4-28 x 6” HWH* #5 .250-.500 7.100 fasteners &
threaded rod
* 3/4” Bonded Washer ** 1-1/8” Bonded Washer

TRUGRIP™ GT METAL-TO-WOOD FASTENERS

Part Head Drill Drill & Tap Max. Material Applications
Number Description Style Point Capacity Attachment • Wall panel to wood structure.
.012-.048 0-.250 • Panel over insulation to wood.
1271000 9-15 x 1” HWH Gimlet .012-.048 0-.750 concrete
1272000 9-15 x 1-1/2” HWH Gimlet .012-.048 1.000-1.750 • Stitching of wall panel. anchors
1275000 9-15 x 2-1/2” HWH Gimlet .012-.048 1.500-2.250 • Roof and wall panel to wood.
1276000 9-15 x 3” HWH Gimlet .012-.048 0-.445 • Panel over insulation to wood.
.012-.048 0-.750
1557000 14-10 x 1” 3/8” AF HWH Type 17 .012-.048 --- • Stitching of roof and wall panel.

1558000 14-10 x 1-1/2” 5/16” AF HWH Type 17 .012-.048 0-.250
.012-.048 0-.750
1277000 12-14 x 3/4” HWH Gimlet .012-.048 .500-1.250
.012-.048 1.000-1.750
With 1/2’’ Bonded Washer Gimlet .012-.048 1.500-2.250
1262000 9-15 x 1” HWH Gimlet .012-.048
1264000 9-15 x 1-1/2” HWH Gimlet ---
1267000 9-15 x 2” HWH Gimlet
1268000 9-15 x 2-1/2” HWH Gimlet
1269000 9-15 x 3” HWH

1270000 12-14 x 3/4”* HWH Gimlet

*With 9/16” O.D. Bonded Washer. specialty items
services & data

317
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
MACHINE SCREWS

TOOLS & FLAT HEAD MACHINE SCREWS ROUND HEAD MACHINE SCREWS
ACCESSORIES SLOTTED AND PHILLIPS SLOTTED AND PHILLIPS

Steel  •  Zinc Plated Steel  •  Zinc Plated

DIAMETER - THREAD DIAMETER - THREAD
LENGTH 6-32 8-32 1/4-20
LENGTH 1/4-20 3/8-16 1/2-13 S
SSS 1/2 S
1/2 SSS 3/4 S
3/4 SSS 1 S
CONTRACTOR 1 SSS 1-1/4 S
SUPPLIES 1-1/4 SSS 1-1/2 S
1-1/2 SSS 1-3/4 S
1-3/4 SSS 2
2 S - Denotes Normally Stocked • Unlisted Items May Be Available
2-1/4 SSS
2-1/2 SSS
2-3/4 SSS
3 SSS pan head combination

S - Denotes Normally Stocked • Unlisted Items May Be Available MACHINE SCREWS
SLOTTED AND PHILLIPS
hangers PAN HEAD MACHINE SCREWS
& strut SLOTTED AND PHILLIPS Steel  •  Zinc Plated

Steel  •  Zinc Plated 6-32 DIAMETER - THREAD
LENGTH S 8-32 1/4-20
DIAMETER - THREAD S S S
LENGTH 6-32 8-32 1/4-20 1/2 S S S
SSS 3/4 S S S
1/2 1 S S
3/4 SSS 1-1/4 S
1 SSS 1-1/2 S
1-1/4 SSS 1-3/4 S
fasteners & 1-1/2 SSS 2
threaded rod 1-3/4 S - Denotes Normally Stocked • Unlisted Items May Be Available
2 SS
SSS

S - Denotes Normally Stocked • Unlisted Items May Be Available

Hex Head Lag Screws

concrete HEX HEAD LAG SCREWS Also Available Not sure?
anchors In Plated and HDG
Steel  •  Plain  •  Plated

LENGTH DIAMETER - THREAD S - Denotes We’re happy to provide you with
Normally Stocked Complete Product Literature
1 1/4 3/8 1/2 and detailed specifications.
1-1/4 SS • Unlisted Items
1-1/2 SS May Be Available Just ask us!
1-3/4 S SS
specialty items SS
services & data 2 S SS
2-1/4 S
2-1/2 S SS
2-3/4 S SS
S SS
3

318
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
hex head cap screws

Steel • Zinc Plated TOOLS &
ASTM A307A • U.S.S. Coarse Thread ACCESSORIES

Note: Thread Length x 2 Dia. + 1/4” Tap Bolts (Full Thread) Available Upon Request

Length (Inches)
Dia.

1/4* 3/4 1 1-1/4 1-1/2 1-3/4 2

3/8* 3/4 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4 3 3-1/4 3-1/2 3-3/4 4 CONTRACTOR
SUPPLIES
1/2*  3/4 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4 3 3-1/4 3-1/2 3-3/4 4 4-1/2

5/8    1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4 3 3-1/4 3-1/2 3-3/4 4 4-1/2 5 5-1/2 6

3/4     1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4 3 3-1/4 3-1/2 3-3/4 4 4-1/2 5 5-1/2 6

7/8    2 2-1/4 2-1/2 2-3/4 3 3-1/4 3-1/2 3-3/4 4 4-1/2 5 5-1/2 6

1    3 3-1/4 3-1/2 3-3/4 4 4-1/2 5 5-1/2 6

1-1/8    3 3-1/4 3-1/2 3-3/4 4 4-1/2 5 5-1/2 6 6-1/2 7 

1-1/4    3 3-1/4 3-1/2 3-3/4 4 4-1/2 5 5-1/2 6 6-1/2 7 

1-1/2    5 5-1/2 6 6-1/2 7 7-1/2 hangers
* Denotes zinc plated only & strut

heavy hex bolts

ASTM A307 GRADE B* fasteners &
Mechanical Properties and Characteristics threaded rod

Material: Low-carbon steel with Phosphorus 0.04% max, Intended primarily for
sulfur 0.05% max flanged joints in piping
systems where one or both
Mechanical Properties: MIN MAX flanges are cast iron. Will
serve well for any general
  Tensile Strength, psi 60,000 100,000 application. The heavy hex
95 head provides maximum
  Hardness, Rockwell B 69 bearing area.

Threads: Coarse treads-UNRC-2A

Finish: Uncoated from stock. Protective coatings - electrogalvanized, hot-dip
galvanized available on special order.
Washer-faced heavy hex head
Head:

Dimensions: Made to heavy-hex bolt standards of ANSI B18 8.2.1 concrete
anchors
Diameter Length (Inches) Sizes beyond the range
2-1/4 2-1/2 of the stock sizes can be
1/2 1-1/2 1-3/4 2 3-/14 3-1/2 2-3/4 produced on special order
3-1/2 3-3/4 4
5/8 2-1/2 2-3/4 3 When ordering Heavy Hex
6 Bolts - DON’T FORGET
3/4 2-3/4 3 3-1/4 5 5-1/2
to order Heavy Hex Nuts
7/8 3-1/2 4 4-1/2 specialty items
Nuts are not services & data
1 4-1/2 5 5-1/2 normally priced
and shipped with these bolts
1-1/8 4-3/4 5 6-1/2

1-1/4 5 5-1/2 6

1-1/2 6 7

* A193 GRADE B-7 ALSO AVAILABLE - SIZES PRICED UPON REQUEST

319
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
HEX NUTS AND COUPLINGS

TOOLS & HEAVY HEX NUTS THREADED ROD COUPLINGS
ACCESSORIES
Steel • Zinc Plated Heavy Duty  •  Steel  •  Plated • U.S.S. Thread

Threads Per Pkg. Bulk* Size & Thread Bulk* Qty.
Size Inch - Coarse Qty. Qty.
1/4 - 20 10,000
1/4 20 100 —
— 3/8 - 16 1,500
5/16 18 100 —
3/8 16 100  — 1/2 - 13 1,500
1/2 13 50  —
CONTRACTOR 5/8 11 50  — 5/8 - 11 1,500
SUPPLIES 650
500 3/4 - 10 500
350
3/4 10 50 270 7/8 - 9 350
7/8 9 —­ 150
1 8 — 100 1-8 250
1-1/8 7 — 65
1-1/4 7 — 11/8 - 7 200
1-1/2 6 — 11/4 - 7 200
1-3/4 5 —
11/2 - 6 150

* Bulk quantities may vary.

Call to confirm availability.

hangers 2 4-1/2 — REDUCING COUPLINGS
& strut
* Bulk quantities may vary. Electro-Zinc Plated • U.S.S. Thread
Call to confirm availability.

Size Size

1/4 x 3/8 5/8 x 3/4

3/8 x 1/2 3/4 x 7/8

1/2 x 5/8

fasteners & * Bulk quantities may vary.
threaded rod Call to confirm availability.

WASHERS

FLAT WASHERS FENDER WASHER

Steel • Zinc Plated Steel • Electro Galvanized

concrete Bulk Qty. Pcs. Per Size I.D. O.D. Wgt. Each
anchors (In. Lbs.)
Size (Lbs. / Box) 10 Lbs. 1/2 9/32 1-1/4
3/8 13/32 1-1/2 .03
1/4 50 1,000 1/2 17/32 2 .03
3/8 50 670 .05
1/2 50 260
specialty items 5/8 50 130
services & data 3/4 50 90
7/8 50 68
1 50 55

1-1/8 50 45

1-1/4 50 38 LOCK WASHERS

1-1/2 50 26 Diameter
3/8 1/2 5/8 3/4 7/8 1
* Bulk quantities may vary. 1-1/8 1-1/4 
Call to confirm availability.

320
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
THREADED ROD

BUNDLED QUANTITIES & WEIGHTS TOOLS &
ACCESSORIES
All Sizes Stocked In Both Plain And Zinc Finish

WT./ 6’ Per Bdl. 10’ Per Bdl.
CFT PCS FT.
SIZE FT. WT. PCS WT.

1/4 (20) 12.0 100 600 72.0 50 500 61
250 49.8
5/16 (18) 20.0 75 450 90.0 25 250 73.3 CONTRACTOR
150 60.3 SUPPLIES
3/8 (16) 29.0 50 300 88.0 25 130 69.3
80 67.5
7/16 (14) 40.0 25 150 60.3 15 50 61.8
50 85.3
1/2 (13) 54.0 25 150 82.0 13 30 67
BULK
5/8 (11) 83.0 15 90 72.0 8 BULK
BULK
3/4 (10) 125.0 10 60 76.0 5 BULK
BULK
7/8 (9) 170.0 9 54 92.0 5 BULK

1 (8) 223.0 6 36 80.0 3

1 1/8 (7) 281.0 4 24 68.0

1 1/4 (7) 354.0 4 24 84.0

1 3/8 (6) 423.0 4 24 102.0 hangers
& strut
1 1/2 (6) 512.0 4 24 122.0

1 3/4 (5) 635.0 BULK

2 (4 1/2) 912.0 BULK

Threaded Studs (all grades) cut to request. Other sizes and lengths are priced on application.

Type 304 and 316 Stainless Steel Threaded Rod fasteners &
also available in 1/4” through 1-1/4” sizes - 6’ and 12’ lengths. threaded rod

HIGH STRENGTH MATERIALS

High Strength-Elevated Temperature Materials concrete
ASTM A193 - B7 Alloy anchors

This Alloy Steel is heat-treated to provide a unique specialty items
combination of high strength and high temperature services & data
properties. Used extensively in the Power Generation
and Petro-Chemical Industries, this is the ultimate in
threaded rod. Tensile Strength is not less that 125,000 psi
with a yield of not less than 105,000 psi. Can be provided
plain or electro-plated zinc / yellow-finish.

In addition to our extensive stock of fully threaded rods,
we will quote you for U-Bolts, Anchor Bolts, Studs or
Special to your print.

321
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
CONCRETE ACCESSORIES

TOOLS & Coil Thread Rod is manufactured using high COIL THREAD
ACCESSORIES tensile steel and incorporates an easy-flow
thread to provide for ease of installation. Coil Thread Rod is available
in 12 ft lengths Watson Metal will provide the

CONTRACTOR product cut to length at a modest
SUPPLIES increase in price. Watson Coil

Thread is manufactured in America
from Steel produced in America.
We meet all requirements of any
state D.O.T. Imported Hex Nuts are
available for all diameters.

hangers CONCRETE STAKES
& strut
Concrete Stakes are used to secure wood or metal forms to
fasteners & the ground. For concrete placement, they can be removed
threaded rod and re-used many times. Manufactured from 1040 steel to
withstand the hammer blows, the stakes have numerous nail
holes to insure one will line up with the form. The nominal
¾ round stake (0.718” diameter) meets the IFI Specifications
and has a paint finish to prolong the life before rust. The
stakes are packed in units of ten with plasticated capes,
wrapped and palletized by length.

We can offer a nominal 7/8” diameter round stake and a 3/8” thick flat stake. In addition, if demand warrants, we will add a full ¾” diameter.
These stakes, imported from India, are very versatile and can be used in a myriad of projects outside of concrete forming.

concrete THREADED ACCESSORIES
anchors
COACH SCREW ROD

FUNCTION: Designed for use as a vertical hanger attachment to wood structures.

specialty items ORDERING: Specify rod size, length, finish and figure number.
services & data
Rod Minimum Length Max. Rec. 4 Wt. Each (in lbs.) 12
Size Load/lbs.
Machine Coach .12 Length D (inches) .37
A BC 390 .22 6 8 10 .67
640 .19 .25 .31
MATERIAL: Low carbon steel 13⁄⁄28 2 2 .34 .44 .56
FINISH: Plain or electro-galvanized 2 21⁄2

322
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
THREADED ACCESSORIES
TOOLS &
ANCHOR BOLTS ACCESSORIES

CONTRACTOR
SUPPLIES

hangers
& strut

ANCHOR BOLT KITS fasteners &
threaded rod

concrete
anchors

Products listed above are imported. specialty items
Material is ASTM A36 C-Steel 1018/1020. services & data

SPECIFICATIONS

• Plain and hot dip galvanized finish
• Packed in boxes with nuts and

washers in poly bags

323
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
THE ANCHORING INDUSTRY
TOOLS &
ACCESSORIES Why is it Changing?

CONTRACTOR The building code serves as the basic
SUPPLIES 'roadmap' that an engineer uses
to design a structure. The previous
hangers versions of the building code (known as legacy codes) did not directly address
& strut post-installed anchoring applications. The new building code which is now in
effect addresses anchor design. In prior years many structural engineers relied
fasteners & on manufacturer based testing programs, technical information provided
threaded rod by manufacturers, and a design method which incorporated safety margins
provided by a standard global factor (Allowable Stress Design).
concrete
anchors However in 2003, the International Building Code (IBC) introduced state-of-
the-art requirements for design, testing and evaluation of anchors. The 2003
specialty items and 2006 IBC is now in place in nearly all United States jurisdictions making
services & data these changes nationwide.

WHAT IS Changing?

The Testing, Evaluations And Approvals

For anchors used in reinforced concrete, previous ICC-ES Evaluation Reports (based on Allowable Stress Design) became invalid
after December 31, 2007. All anchoring products now are required to comply with the IBC through new product specific testing
and evaluation. Approvals for non-reinforced masonry will remain provided the reports are renewed.

The Anchors

New anchors are being designed to meet the new criteria. Powers is leading the way with more than 12 new solutions.

The Design Method

Allowable Stress Design (ASD) is being replaced by Strength Design (SD). The old method of applying a 4:1 or 10:1 safety
factor (as determined by the engineer) is no longer applicable under the new International Building Code. Only Strength
Design will be used in the future and along with its use new anchors are being tested to these new standards.

324
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products

WHAT IS STRENGTH DESIGN? TOOLS &
ACCESSORIES
Strength Design is a design procedure used by engineers to ensure acceptable levels of safety and
the proper functioning of a structure for its expected lifetime. Strength Design is based on statistics,
engineering principles and a general knowledge of material behavior. When applied to anchoring,
Strength Design requires the factored resistance to be greater than the factored loading. OR

>Anchor Strength Reduced by Forces Acting on an Anchor CONTRACTOR
SUPPLIES
a Strength Reduction Factor Increased by a Load Factor

(Factored Resistance) (Factored Load)

HOW DOES STRENGTH DESIGN APPLY IN ANCHORAGE IN CONCRETE? hangers
& strut
The 2003 International Building Code requires post-installed anchors to be designed according to ACI 318 Appendix D which is based
on Strength Design. Furthermore, Appendix D requires post-installed anchors to be tested and qualified according to ACI 355.2 (which fasteners &
is supplemented by ICC-ES Acceptance Criteria 193). ACI 355.2 introduced several new tests including the performance of anchors in threaded rod
cracked concrete conditions.
concrete
WHAT PRODUCTS CONFORM? anchors

Powers Fasteners has began introducing the "+" line of Strength Design products and will
continue throughout the coming years. These products have been or will be tested for compliance
with the 2003 IBC. The "+" product line includes Power-Stud+ SD1, SD2, SD3, SD4 and SD5,
Wedge-Bolt+ BT and OT, Power-Bolt+, Tapper+, Vertigo+, Spike+, Snake+, AC100+Gold and
PE1000+.

To the date of this catalog’s release, Powers has completed testing on the Power-Stud+ SD2 and
Snake+ where many sizes are now in stock. Both products have been evaluated by an independent
testing agency as a Category 1 anchor which is highest reliability rating obtainable.

all new design anchoring + systems products
will have the following features and benefits:

• Qualification testing for building code compliance (2003 and 2006 IBC) Your Newman representative will keep you specialty items
• Performance over a wide range of compressive strength (2500ñ8500 psi) informed of the advances made by services & data
• Knowledge of failure mode of the anchor Powers Fasteners as the new ‘+’ line
• Increased safety, reliability and confidence in anchor performance
• Design for cracked concrete conditions of Strength Design products are fully tested,
• Easy calculations of anchor groups approved and become available for purchase.

325
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
MECHANICAL ANCHOR SELECTION GUIDE

TOOLS & Anchor Category Expansion Anchors Screw Anchors Rod Hanging Systems
ACCESSORIES
Power-Bolt
CONTRACTOR Product Power-Stud
SUPPLIES Lok-Bolt
Set-Bolt
Wedge-Bolt
Tapper
Vertigo
Bang-It
Wood-Knocker

Concrete n nn n n n n nn

Lightweight Concrete n nn o n n n nn

Hollow Core Plank o o on n

Grout-filled Concrete Masonry n oo o n n

Base Material Hollow Concrete Masonry o n on

Solid Brick n n on n

Hollow Brick o o o

hangers Stone o o o o o
& strut
Structural Clay Tile o

Wood n

Steel n

3/16" n

1/4" n n n n n n n nn

Anchor Diameter 5/16" n n

8 mm

fasteners & 3/8" n n n n n n n nn
threaded rod
1/2" n n n n n n nn

5/8" n n n n nn

3/4" n n n n nn

7/8" n n

1" n

1 1/4" n

Finished Hex Head n nn

Round / Acorn Head n

Head Style Flat Head (Countersunk) n n n

concrete Mushroom Head
anchors
Removable n nn n

Tie-Wire Head nn

Tamperproof

Female Coupler nn nn

Coated / Plated Carbon Steel n nn n n n n nn

Coating/Material Galvanized Steel n n

Type 303/304 Stainless Steel n n n n

specialty items Type 316 Stainless Steel n
services & data
Type 410 Stainless Steel nn

Perma-Seal Coated n

Nylon / Plastic nn

n - Suitable
o - May Be Suitable

326
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
MECHANICAL ANCHOR SELECTION GUIDE

Anchor Category Bolt and Shield Anchors Facade Pin Nail Anchors TOOLS &
Anchor Anchors ACCESSORIES

Product Snake Heli-Pin Spike CONTRACTOR
Hollow-Set Dropin Drive SUPPLIES
Steel Dropin Zamac Hammer-
Mini Dropin Screw
Double Zamac Nailin
Single Nylon Nailin
Calk-In
Lag-Shield

Concrete n n n n n n n n n nn nn n

Lightweight Concrete n o n n o o o o n no oo o

Hollow Core Plank n n n oo o

Base Material Grout-filled Concrete Masonry o n o oonn n no oo o

Hollow Concrete Masonry n n no nn n

Solid Brick n nonn n oo nn n

Hollow Brick o o oo o hangers
& strut
Stone ooo oooo o oo oo o

Structural Clay Tile

Wood

Steel

Anchor Diameter 3/16" nn nn

1/4" n n n n n n n n nn nn n

5/16" n nnnn

8 mm n fasteners &
threaded rod
3/8" n n n n n n n n nn

1/2" n n n n n n n nn

5/8" n n nn n

3/4" n n n n

Mushroom Head nn nn n

Head Style Round Head n

Flat Head (Countersunk) nn nn

Tie-Wire nn

Removable n

Tamperproof nn nn concrete
anchors
Flush Mount n n n n n n n n n

Coated / Plated Carbon Steel n n n n nn nn n

Coating/Material Galvanized Steel

Type 303/304 Stainless Steel nn nn n

Type 316 Stainless Steel n nn

Type 410 Stainless Steel

Zamac Alloy n nnnn nn

Perma-Seal Coated n specialty items
services & data
Nylon / Plastic n

Lead n

n - Suitable
o - May Be Suitable

327
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
MECHANICAL ANCHORS

POWER STUD™+

TOOLS & CARBON
ACCESSORIES
POWER-STUD™ + SD1 The POWER-STUD™ + SERIES anchors are fully threaded, torque-controlled,
wedge expansion anchors designed for consistent performance in cracked and
Carbon steel body plus carbon steel clip. uncracked concrete. General applications include structural connections (i.e., beam
and column anchorage), safety-related attachments, Interior applications / low level

power stud™ +SD1 corrosion environment, tension zone applications (i.e., cable trays and strut, pipe
supports and fire sprinklers), seismic and wind loading applications.
Carbon steel body plus carbon steel clip

OLD NEW STD. STD. ThOLeDPower-SNtEuWd™ + SD1 and Power-Stud™ + SD2 featured on tShTDis. pageSaTDre.
CAT. NO. CAT. NO. BOX CTN.
CONTRACTOR DESCRIPTION SIZE lsCC00iguA77aPhiT44tr.tabO33Nwbo68OWeln.eigEsfthoRe77treC-44cbSlA33oTabT86.nsoNSSUcedDDOrDy.11em™tpeal+utaesnrSsidaDtalPPcs2ioonotwwlnheeecasDrrst--EeSSSistntCteuueRcddeIloPu++lvTdcIeOSSelriDDNpnm11. oeCCrtmSSaladl-ewce5ki/.g85h"/8tSx"cIZ8oxE-n71c”/r2e”te, stBrOuXctural CsTaNn.d /
SUPPLIES 07400 7400SD1 100 500 100 500
07402 7402SD1 Power-Stud+ SD1 CS 1/4" x 1-3/4” 100 500
Power-Stud+ SD1 CS 1/4" x 2-1/4” 100 500

07404 7404SD1 Power-Stud+ SD1 CS 1/4" x 3-1/4” 100 500 07439 7439SD1 Power-Stud+ SD1 CS 5/8" x 10” 100 500
07410 7410SD1 Power-Stud+ SD1 CS 3/8" x 2-1/4” 100 500 p074o40we74r40SsD1tudP™ower+-StSud+DS2D1 CS 3/4" x 4-1/4” 100 500

07412 7412SD1 Power-Stud+ SD1 CS 3/8" x 2-3/4” 100 500 C0a7r4b4o1n ste7e4l4b1oSDd1y plus stPaoinwlers-Sstusdte+elSDcl1ipCS 3/4" x 4-3/4” 100 500

07413 7413SD1 Power-Stud+ SD1 CS 3/8" x 3” 100 500 074O4LD2 7442NSEDW1 Power-Stud+ SD1 CS 3/4" x 5-1/2” 10S0TD. 50S0TD. OLD
CAT. NO.
07414 7414SD1 Power-Stud+ SD1 CS 3/8" x 3-1/2” 100 500 07C4A4T.4NO. 744C4AST.DN1O. Power-DStEuSdC+RIPSTDIO1NCS 3/4" x 6SI-Z1E/4” 10B0OX 50C0TN.
0704040600 7474461S3DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 3/43"/8x" 7x”3” 101000 505000 00000 7
000C777aP444rbO111o657Wn EstRe777e444-Sl111b756ToSSSUDdDDDy111™pl+usSsDtaPPP2iooonwwwleeeesrrrs---SSSsttttuuueddde+++l SD1 CS 3/8" x 3-3/4” 100 500 0704040800 7474481S5DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 3/43"/8x" 8x-31-/23”/4” 101000 505000 00000 7
cSSliDDp11. CS 3/8" x 5” 100 500 0704040900 7474491S6DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 3/43"/8x"1x0”5” 101000 505000 00000 7
CS 3/8" x 7” 100 500 0704050000 7475402S2DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 17//28"" xx 36-”3/4” 101000 505000 00000 7
00000 7
hangers 07420 7420SD1 Power-Stud+ SD1 CS 1/2" x 2-3/4” 100 500 0704050100 7475412S3DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 31//42""xx142-”1/2” 101000 505000 00000 7
& strut 00000 7
07422 7422SD1 Power-Stud+ SD1 CS 1/2" x 3-3/4” 100 500 0704050200 7475422S4DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 17//28"" xx 58-”1/2” 101000 505000 00000 7
00000 7
07423 7423SD1 Power-Stud+ SD1 CS 1/2" x 4-1/4” 100 500 0704O05L04D00 7475442NS6EDWS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 7/81"/2x"1x0”7” 101S0T0D0. 505S0T0D0.
070C4A06T01.0N0O. 7476C41A2ST7.DSN1DO.2 PoPwoewr-eSDrt-EuSSdtCu+RdIP+STDISO1DNC2SCS 11/2""xSx6IZ8”E-1/2” 101B00O0X 505C0T0N0.
074O2L4D 7424NSEDW1 Power-Stud+ SD1 CS 1/2" x 5-1/2” 10S0TD. 50S0TD.
07C4A2T6. NO. 742C6AST.DN1O. Power-SDtEuSdC+RIPSTDIO1NCS 1/2" SxIZ7E” 10B0OX 50C0TN.
0704020700 7472471S3DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 1/2"3x/88"-1x/23”” 101000 505000 0704060300 7476433S5DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 51/8""xx94”-3/4” 101000 505000
0704030000 7473401S5DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 5/83"/8x"3x-13/-23”/4” 101000 505000 0704060500 7476453S3DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 1"5/x81"2x”5” 101000 505000
0704030200 7473421S6DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 5/8"3x/84"-1x/25”” 101000 505000 0704070300 7477433S4DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 1-15/4/8""xx96”” 101000 505000
00CO77A00TL44.D0033N0034O00.00 7744C77A33N44T43E.22WSSN23DDOSS.11DD22 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 51//82"" xx 53”-3/4” 11SB00TO11D00X.0000 55CS00TT55ND00.00. 00 0704070500 7477453S4DS1D2 PoPwoewr-eSrt-uSdtu+d+SDS1DC2SCS 1-1/54/"8"x 1x27”” 101000 505000
STD.fasteners & PoPwoewDr-EeSSrt-CuSRdtIuP+dTI+SODNS1DC2SCS 51//82S""IZxxE64”-1/2” 00000 7438SD2 Power-Stud+ SD2 CS 5/8" x 8-1/2” 100 500
CTN.threaded rod
0704030600 7473462S4DS1D2 PoPwoewr-eSr-tuStdu+d+SDS1D2CSCS 15//28"" xx 57-”1/2” 101000 505000 00000 7442DS2 Power-Stud+ SD2 CS 3/4" x 5-1/2” 100 500
500
0704030800 7473482S6DS1D2 PoPwoewr-eSrt-uStdu+d+SDS1D2CSCS 5/8"1x/28"-1x/72”” 101000 505000 00000 7444SD2 Power-Stud+ SD2 CS 3/4" x 6-1/4” 100 500
500
0704030900 7473492S7DS1D2 PoPwoewr-eSr-tuStdu+d+SDS1D2CSCS 51//82""xx180-”1/2” 101000 505000 00000 7446SD2 Power-Stud+ SD2 CS 3/4" x 7” 100 500
500
00000 7448SD2 Power-Stud+ SD2 CS 3/4" x 8-1/2” 100 500
500 07440 7440SD1 Power-Stud+ SD1 CS 3/4" x 4-1/4” 100 500

500 07441 7441SD1 Power-Stud+ SD1 CS 3/4" x 4-3/4” 100 500

500 07442 7442SD1 Power-Stud+ SD1 CS 3/4" x 5-1/2” 100 500 COMING SOON...

500 07444 7444SD1 Power-Stud+ SD1 CS 3/4" x 6-1/4” 100 500

500 07446 7446SD1 Power-Stud+ SD1 CS 3/4" x 7” 100 500 additional POWER-STUD™ + Anchors will become available

500 07448 7448SD1 Power-Stud+ SD1 CS 3/4" x 8-1/2” 100 500 during 2008 PENDING FINAL APPROVALS AND LISTINGS.*
concrete
500anchors 07449 7449SD1 Power-Stud+ SD1 CS 3/4" x 10” 100 500 POWER-STAUDsk™ +yoSuDr3Newman representative about...

500 07450 7450SD1 Power-Stud+ SD1 CS 7/8" x 6” 100 500 Galvanized body plus carbon steel clip.

500 07451 7451SD1 Power-Stud+ SD1 CS 3/4" x 12” 100 500

500 07452 7452SD1 Power-Stud+ SD1 CS 7/8" x 8” 100 500 POWER-STUD™ + SD3: Galvanized body plus carbon steel clip

500 07454 7454SD1 Power-Stud+ SD1 CS 7/8" x 10” 100 500 POWER-STUD™ + SD4: 304 Stainless steel body plus stainless steel clip

500 07461 7461SD1 Power-Stud+ SD1 CS 1" x 6” 100 500

500 07463 7463SD1 Power-Stud+ SD1 CS 1" x 9” 100 500 CPOATOL.DWNOE. R-SCTANUTE.DWN™O. + SD5: 31D6ESSCRtaIPiTnIOleNss steel bodySpIZlEus stainlSBeTOsDXs. steeCSlTTcND.l.ip OLD
CAT. NO.
500 07465 7465SD1 Power-Stud+ SD1 CS 1" x 12” 100 500
specialty items 07741
500services & data 07473 7473SD1 Power-Stud+ SD1 CS 1-1/4" x 9” 100 500 00•*77A77InP22t03PerRnOa77tVi77oA22nL30aSSSl DDCA33oNdeD CLoIPPSuoonwwTcIeeiNrrl,--SSGEttSuuvdda++luaSStDDio33nGGSaaellvvr.. vice 1/2" x 2-3/4" 100 500 07742 7
500 07P4O75WER7-4S7T5SUDD1™ + SDP3ower-Stud+ SD1 CS 1-1/4" x 12” 100 500 1(/IC2"Cx-E4S-1),/2E"SR P1e0n0ding 500 07748 7
07750 7
500 Galvanized body plus carbon steel clip. 0•77T2e4sted 7in72a4cScDo3rdancePwowitehr-AStCuId3+5S5D.32Gaanldv. AC119/32"crxit5e-r1ia/2" 100 500 07752 7
07763 7
0•77E2v6aluat7e7d2a6nSDd3qualifiePdowbeyr-aSntuad+ccSreDd3itGeadlvi.ndepen1d/2e"nXt t7e"sting la1b0o0ratory5f0o0r 7
077u3s0e in c7r7a3c0kSeDd3and unPocwraecrk-Setdudc+onSDcr3eGtealivn.cludi5n/g8"seXis3m-1i/c2"and w1i0n0d load5in0g0

0•77S3t4rengt7h73D4eSsDig3n methPodwearc-Sctourdd+inSgDt3oGAaClvI. 318, A5p/8p"enXd6ix" D 100 500

OLD NEW DESCRIPTION STD. STD. OLD NEW DESCRIPTION STD. STD.
CAT. NO. CAT. NO. SIZE BOX CTN. CAT. NO. CAT. NO. SIZE BOX CTN.

07720 7720SD3 Power-Stud+ SD3 Galv. 1/2" x 2-3/4" 100 500 07741 7741SD3 Power-Stud+ SD3 Galv. 3/4" x 4-3/4" 100 500
07723 7723SD3
328 07724 7724SD3 Power-Stud+ SD3 Galv. 1/2" x 4-1/2" 100 500 07742 7741SD3 Power-Stud+ SD3 Galv. 3/4" x 5-1/2" 100 500
07726 7726SD3
07730 7730SD3 Power-Stud+ SD3 Galv. 1/2" x 5-1/2" 100 500 07748 7748SD3 Power-Stud+ SD3 Galv. 3/4" x 8-1/2" 100 500
Power-StudT+ HSD3EGaClv.O N S1/T2"RXU7"C T I1O00N S5U00P P LY S P07E75C0I A7L75I0SSDT3 . . P.owWer-SHtudE+ RSDE3 GSalvE. R V7I/8C"EX 6C" O M10E0S F5I0R0 S T

Power-Stud+ SD3 Galv. 5/8" X 3-1/2" 100 500 07752 7752SD3 Power-Stud+ SD3 Galv. 7/8" X 8" 100 500

WEDGE-BOLT+ ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
Blue Tip – Standard Fixture Hole Clearance

MECHANICAL ANCHORS

OLD NEW DESCRIPTION wedge-bolt+STD. STD. OLD NEW DESCRIPTION STD. STD.
CAT. NO. CAT. NO. SIZE BOX CTN. CAT. NO. CAT. NO. SIZE BOX CTN.
Wedge-Bolt+ SD BT
07204 7204SD Wedge-Bolt+ SD BT 1/4" x 1-1/4” 100 500 07246 7246SD Wedge-Bolt+ SD BT 1/2" x 4" 100 500 TOOLS &
07248 7248SD Wedge-Bolt+ SD BT 1/2" x 5" 100 500 ACCESSORIES
07206 7206SD Wedge-Bolt+ SD BT 1/4" x 1-3/4” 100 500 07250 7250SD Wedge-Bolt+ SD BT 1/2" x 6" 100 500
07260 7260SD Wedge-Bolt+ SD BT 5/8" x 3" 100 500
07208 7208SD Wedge-Bolt+ SD BT 1/4" x 2-1/4” 100 500 07262 7262SD Wedge-Bolt+ SD BT 5/8" x 4" 100 500
07264 7264SD Wedge-Bolt+ SD BT 5/8" X 5" 100 500
0W7E21D0GE-B72O1L0TS+D Wedge-Bolt+ SD BT 1/4" x 3” 100 500 07266 7266SD Wedge-Bolt+ SD BT 5/8" X 6" 100 500
07280 7280SD Wedge-Bolt+ SD BT 3/4" x 3" 100 500
Blu07e2T2ip0 – Sta7n2d20aSrdDFixture HWoeledgCel-eBaorlat+ncSeD BT 3/8" x 1-3/4" 100 500 07282 7282SD Wedge-Bolt+ SD BT 3/4" x 4" 100 500
0O7L2D84 72N8E4WSD 3/4" x 5" 1ST0D0. 5ST0D0.
07222 7222SD Wedge-Bolt+ SD BT 3/8" x 2-1/2” 100 500 DESCRIPTION
CAT. NO. CAT. NO. SIZE BOX CTN.
WBlu000e777E222T222Dip846 -GStE777a222n-222d486BaSSSrDDDdOFiLxtTur+e WWWHoeeeldddegggeeeC---lBBBeoooalllrttta+++nSSScDDDe BT 3/8" x 3" 100 500 WWeeddggee--BBoolltt++ SSDD BBTT
BT 0077228466 77228466SSDD WWeeddggee--BBoolltt++ SSDD BBTT 13//42"" xx 46"" 110000 550000
BT 3/8" x 4" 100 500 0077224888 77228488SSDD Wedge-Bolt+ SD BT 31//42"" xx 58"" 110000 550000
07250 7250SD Wedge-Bolt+ SD BT 1/2" x 6" 100 500
3/8" x 5" 100 500 07260 7260SD Wedge-Bolt+ SD BT 5/8" x 3" 100 500
07262 7262SD Wedge-Bolt+ SD BT 5/8" x 4" 100 500
0O7L2D30 72N3E0WSD Wedge-Bolt+ SD BT 3/8"x 6" 1ST0D0. 5ST0D0. 07264 7264SD Wedge-Bolt+ SD BT 5/8" X 5" 100 500 CONTRACTOR
07266 7266SD Wedge-Bolt+ SD BT 5/8" X 6" 100 500 SUPPLIES
CAT. NO. CAT. NO. DESCRIPTION SIZE BOX CTN. 07280 7280SD Wedge-Bolt+ SD BT 3/4" x 3" 100 500
07282 7282SD Wedge-Bolt+ SD BT 3/4" x 4" 100 500
0077224004 77224004SSDD WWeeddggee--BBoolltt++ SSDD BBTT 1/41"/2x" 1x-21"/4” 110000 550000 07284 7284SD Wedge-Bolt+ SD BT 3/4" x 5" 100 500
0077224026 77224026SSDD WWeeddggee--BBoolltt++ SSDD BBTT 11//24"" xx 21--13//24"” 110000 550000 07286 7286SD Wedge-Bolt+ SD BT 3/4" x 6" 100 500
0077224048 77224048SSDD WWeeddggee--BBoolltt++ SSDD BBTT 1/41"/2x" 2x-31"/4” 110000 550000 07288 7288SD 3/4" x 8" 100 500

07210 7210SD Wedge-Bolt+ SD BT 1/4" x 3” 100 500

07220 7220SD Wedge-Bolt+ SD BT 3/8" x 1-3/4" 100 500

07222 7222SD Wedge-Bolt+ SD BT 3/8" x 2-1/2” 100 500

07224 7224SD Wedge-Bolt+ SD BT 3/8" x 3" 100 500

07226 7226SD Wedge-Bolt+ SD BT 3/8" x 4" 100 500

07228 7228SD Wedge-Bolt+ SD BT 3/8" x 5" 100 500

07230 7230SD Wedge-Bolt+ SD BT 3/8"x 6" 100 500

07240 7240SD Wedge-Bolt+ SD BT 1/2" x 2" 100 500 hangers
& strut
W07E24D2GE-B72O4L2TS+D Wedge-Bolt+ SD BT 1/2" x 2-1/2" 100 500

Or0a7n2g4e4Tip –7O24v4erSsDized FixtuWreeHdgoele-Bsolt+ SD BT 1/2" x 3" 100 500

WEDGE-BOLT+

Orange Tip - Oversized Fixture Holes

OLD NEW DESCRIPTION SIZE STD. STD. OLD NEW DESCRIPTION SIZE STD. STD.
CAT. NO. CAT. NO. BOX CTN. CAT. NO. CAT. NO. BOX CTN.
1/4" x 1-1/4” Wedge-Bolt+ SD OT 5/8" x 5"
07214 7214SD Wedge-Bolt+ SD OT 1/4" x 3” 100 500 07221 7221SD Wedge-Bolt+ SD OT 5/8" x 6" 100 500 fasteners &
3/8" x 4" 100 500 07227 7227SD Wedge-Bolt+ SD OT 5/8" x 6" 100 500 threaded rod
07215 7215SD Wedge-Bolt+ SD OT 1/2" x 4” 100 500 07229 7229SD Wedge-Bolt+ SD OT 3/4" x 3" 100 500
1/2" x 5" 100 500 07231 7231SD Wedge-Bolt+ SD OT 3/4" x 8" 100 500
07216 7216SD Wedge-Bolt+ SD OT 5/8" x 4” 100 500 07232 7232SD Wedge-Bolt+ SD OT 1/2" X 6-1/2" 100 500
100 500 07233 7233SD 100 500
0W7E21D7GE-B72O1L7TS+D Wedge-Bolt+ SD OT

Or0a7n2g1e8Tip –7O21v8erSsDized FixtuWreeHdgoele-Bsolt+ SD OT
07219 7219SD Wedge-Bolt+ SD OT

OLD STD.
CTN.
your solutionCAT.NO.
NEW DESCRIPTION STD. 500 OLD NEW DESCRIPTION SIZE STD. STD.
CAT. NO. SIZE BOX 500 CAT. NO. CAT. NO. BOX CTN.
500 Wedge-Bolt+ SD OT 5/8" x 5"
07214 7214SD Wedge-Bolt+ SD OT 1/4" x 1-1/4” 100 500 07221 7221SD Wedge-Bolt+ SD OT 5/8" x 6" 100 500 concrete
07215 7i2s15SjDust one phoneWedge-Bolt+ SD OT c1a/4l"lx 3a” wa1y00 500 07227 7227SD Wedge-Bolt+ SD OT 5/8" x 6" 100 500 anchors
Wedge-Bolt+ SD OT 3/8" x 4" 100 500 07229 7229SD Wedge-Bolt+ SD OT 3/4" x 3" 100 500
Wedge-Bolt+ SD OT 1/2" x 4” 100 07231 7231SD Wedge-Bolt+ SD OT 3/4" x 8" 100 500
07216 7216SD 07232 7232SD Wedge-Bolt+ SD OT 1/2" X 6-1/2" 100 500
07233 7233SD 100 500
800-733-008907217 7217SD
07218 7218SD Wedge-Bolt+ SD OT 1/2" x 5" 100

07219 7219SD Wedge-Bolt+ SD OT 5/8" x 4” 100

“The foundation of our business specialty items
is customer service.” services & data

329
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
MECHANICAL ANCHORS

TOOLS & LOK-BOLT™ sleeve type expansion Anchors
ACCESSORIES
Sleeve Type Expansion Anchor

BASE MATERIAL

Concrete, Block, Brick

SIZE RANGE

1/4" x 5/8" to 3/4" x 7-1/2"

ANCHOR MATERIAL

Carbon Steel & Stainless Steel

The Lok-Bolt™ anchor is a pre-assembled single unit sleeve anchor available in ACORN NUT LOK-BOLT™ CARBON STEEL
carbon steel and stainless steel which can be used in concrete, block, brick and
stone. Extension sleeves are added to create longer lengths. CAT. DRILL MIN. STD. STD.
NO . SIZE DIA. EMBED. BOX CTN.

CONTRACTOR 5125** 1/4" x 5/8" 1/4" 1/2" 100 1000
SUPPLIES
5150 1/4" x 1-3/8" 1/4" 1-1/8" 100 1000

5175 1/4" x 2-1/4" 1/4" 1-1/8" 100 1000

The published length is measured from below the washer to the end of the anchor.

** This size does not have a compression ring.

HEX NUT LOK-BOLT™ CARBON STEEL ACORN NUT LOK-BOLT 304 STAINLESS STEEL

CAT. DRILL MIN. STD. STD. CAT. DRILL MIN. STD. STD.
BOX CTN. CTN.
NO. SIZE DIA. EMBED. NO . SIZE DIA. EMBED. BOX

5005 5/16" x 1-1/2" 5/16" 1-3/8" 100 1000 6150 1/4" x 1-3/8" 1/4" 1-1/8" 100 1000

5010 5/16" x 2-1/2" 5/16" 1-1/2" 100 500 The published length is measured from below the washer to the end of the anchor.

hangers 5015 3/8" x 1-7/8" 3/8" 1-5/8" 50 500
& strut
5020 3/8" x 3" 3/8" 1-5/8" 50 500

5022 3/8" x 4" 3/8" 1-5/8" 50 250

5025 1/2" x 2-1/4" 1/2" 2-1/8" 25 250

5030 1/2" x 3" 1/2" 2-1/4" 25 250

5034 1/2" x 4" 1/2" 2-1/4" 25 125

5033 1/2" x 5-1/4" 1/2" 2-1/4" 25 125

5032 1/2" x 6" 1/2" 2-1/4" 10 100 ROUND HEAD LOK-BOLT™ CARBON STEEL

fasteners & 5035 5/8" x 2-1/4" 5/8" 2-1/8" 25 125 CAT. DRILL MIN. STD. STD.
threaded rod NO. SIZE DIA. EMBED. BOX CTN.
5038 5/8" x 3" 5/8" 2-3/4" 25 125
100 1000
5040 5/8" x 4-1/4" 5/8" 2-3/4" 10 100 5205** 1/4" x 1-1/8" 1/4" 1" 100 1000
100 1000
5045 5/8" x 6" 5/8" 2-3/4" 10 100 5210 1/4" x 2" 1/4" 1-1/8" 50 500

5050 3/4" x 2-1/2" 3/4" 2-1/8" 10 100 5215 1/4" x 2-3/4" 1/4" 1-1/8" 50 250

5055 3/4" x 4" 3/4" 3-3/8" 10 40 5235 3/8" x 2-1/2" 3/8" 1-5/8" STD.
CTN.
5060 3/4" x 5-3/4" 3/4" 3-3/8" 10 30 5240 3/8" x 3-3/4" 3/8" 1-5/8"
1000
5065 3/4" x 7-1/2" 3/4" 3-3/8" 10 30 ** This size does not have a compression ring.

The published length is measured from below the washer to the end of the anchor.

concrete ROUND HEAD LOK-BOLT™ 304 STAINLESS STEEL
anchors
HEX NUT LOK-BOLT™ 304 STAINLESS STEEL CAT. DRILL MIN. STD.
NO. SIZE DIA. EMBED. BOX

CAT. DRILL MIN. STD. STD. 6180 1/4" x 2" 1/4" 1-1/8" 100
CTN.
NO. SIZE DIA. EMBED. BOX

6152 3/8" x 1-7/8" 3/8" 1-5/8" 50 500

6153 3/8" x 3" 3/8" 1-5/8" 50 500 Think Safety First...

6156 1/2" x 2-1/4" 1/2" 2-1/8" 25 250 WE DO!

6157 1/2" x 3" 1/2" 2-1/4" 25 250 Our Safety Section
Begins on Page 1.
specialty items 6160 1/2" x 4" 1/2" 2-1/4" 25 125
services & data
6164 5/8" x 4-1/4" 5/8" 2-3/4" 10 100

6168 3/4" x 4" 3/4" 3-3/8" 10 40

The published length is measured from below the washer to the end of the anchor.

330
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
MECHANICAL ANCHORS

LOK-BOLT™ sleeve type expansion Anchors

COMBO FLAT HEAD LOK-BOLT™ CARBON STEEL ROD HANGER LOK-BOLT™ CARBON STEEL TOOLS &
ACCESSORIES

CAT. DRILL MIN. STD. STD. CAT. DRILL MIN. STD. STD.
CTN. BOX CTN.
NO. SIZE DIA. EMBED. BOX NO. SIZE DIA. EMBED.
1000 50 250
5305** 1/4" x 1-1/8" 1/4" 1" 100 1000 5810 1/4" x 1-1/2" 5/16" 1-1/2" 50 250 CONTRACTOR
1000 25 125 SUPPLIES
5310 1/4" x 2" 1/4" 1-1/8" 100 500 5815** 3/8" x 1-7/8" 3/8" 1-5/8"

5315 1/4" x 3" 1/4" 1-1/8" 100 500 5825** 1/2" x 2-1/4" 1/2" 2-1/4"
1000
5320 1/4" x 4" 1/4" 1-1/8" 100 ** This size does not have a compression ring.
500
5325 1/4" x 5-1/4" 1/4" 1-1/8" 100 250
250
5330 5/16" x 2-1/2" 5/16" 1-1/2" 100 250

5340 3/8" x 2-3/4" 3/8" 1-5/8" 50

5345 3/8" x 4" 3/8" 1-5/8" 50

5350 3/8" x 5" 3/8" 1-5/8" 50

5360 3/8" x 6" 3/8" 1-5/8" 50

** This size does not have a compression ring. TIE-WIRE LOK-BOLT™ hangers
& strut
COMBO FLAT HEAD LOK-BOLT™ 304 STAINLESS STEEL CAT. DRILL MIN. STD. STD.
NO. SIZE DIA. DEPTH BOX CTN.

5700 5/16" x 1-1/2" 5/16" 1-1/2" 100 1000

CAT. DRILL MIN. STD. STD.

NO. SIZE DIA. EMBED. BOX CTN.

6170 1/4" x 2" 1/4" 1-1/8" 100 1000

6172 1/4" x 3" 1/4" 1-1/8" 100 1000

6174 3/8" x 4" 3/8" 1-5/8" 50 250

6175 3/8" x 5" 3/8" 1-5/8" 50 250 fasteners &
threaded rod
6176 3/8" x 6" 3/8" 1-5/8" 50 250

These parts do not have a compression ring. LOK-BOLT™ EXTENDERS CARBON STEEL

(FOR ADDITIONAL LENGTH) DRILL STD. STD.
CAT. DIA. BOX CTN.
NO. SIZE

5684 3/8 x 1-1/4" 3/8" 50 500

THRESHOLD FLAT HEAD LOK-BOLT™

CAT. DRILL MIN. STD. STD. concrete
BOX CTN. anchors
NO. SIZE DIA. DEPTH
100 1000
5500 1/4" x 2" 1/4" 1-1/8"

This part does not have a compression ring.

PrOoumrpt Processing specialty items
services & data
will have YOUR order
on its way ...FAST!

331
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
MECHANICAL ANCHORSConcrete Screw
BASE MATERIAL
Concrete, Block and Brick

SIZE RANGE

tapper™ CONCRETE screws and3/1d6" xr1-i1l/4"ltob3/8i"txs6"
ANCHOR MATERIAL

TOOLS & Concrete Screw Carbon Steel, Type 304 & Type 410 Stainless Steel
ACCESSORIES
BASE MATERIAL The TAPPER™ Anchoring System is a family of screw anchors, specially designed
drill bits and installation tools designed to meet the needs of most light to medium
Concrete, Block and Brick

SIZE RANGE duty applications in concrete, block and brick. The TAPPER™ concrete screw anchor
is produced in either hex washer head or Phillips flat head styles from Perma-Seal™
3/16" x 1-1/4" to 3/8" x 6" coated carbon steel and Type 304 and Type 410 stainless steel.
The 3/8" size is made in zinc plated carbon steel.
ANCHOR MATERIAL

Carbon Steel, Type 304 & Type 410 Stainless Steel

The TAPPER™ Anchoring System is a family of screw anchors, specially designed

drill bits and installation tools designed to meet the needs of most light to medium

CONTRACTOR duty applications in concrete, block and brick. The TAPPER™ concrete screw anchor
SUPPLIES
is produced in either hex washer head or Phillips flat head styles from Perma-Seal™

cTohSBaeTtLAe3NUd/D8EAc"RaPDrsbiEzPoARenCMiKssAtmAGeIe-aNlSdGaEe-1nA0idn0LTSz™yCinpRTceEAWp3SPl0aAP4tNeEDadRn1cd™aDrRTHbIyLopELneXPE4sRtH1eB0EeOlAX.stDainless steel. CARBIDE DRILL BITS FOR PERMA-SEAL™ AND 410 SS TAPPER™

CAT. STD. STD. DRILL REFERENCES TAPPER™ Drill Bits in the diameters listed are nominal size. 3/16" and 1/4" Perma-

NO. SIZE BOX CTN. STRAIGHT SDS HEX Seal™ TAPPER™ anchors must be installed with special tolerance TAPPER™ drill

2700 3/16" x 1-1/4" 100 500 2781 2793 bits. 1/4" Stainless Steel TAPPER™ anchors require the use of specific tolerance

2702 3/16" x 1-3/4" 100 500 2781 2793 TAPPER™ drill bits, which are gold or silver colored, to denote the standard size

2704 3/16" x 2-1/4" 100 500 2782 2793 and special application size for harder materials. 3/8" diameter TAPPER™ anchors

2706 3/16" x 2-3/4" 100 500 2782 2793 should be installed with a 1/4" ANSI drill bit.

hangers 2708 3/16" x 3-1/4" 100 500 2783 2794 Tolerance Range = 0.168" to 0.175" for the 5/32" and 0.202" to 0.204" for the
& strut 2710 3/16" x 3-3/4" 100 500 2783 2794 3/16" bits. (Do not use with Type 304 Stainless Steel TAPPER™)
2712 3/16" x 4" 100 500 2783 2794

fasteners & 2720 1/4" x 1-1/4" 100 500 2785 2796 STRAIGHT SHANK USABLE STD.
threaded rod 2722 1/4" x 1-3/4" 100 500 2785 2796 LENGTH TUBE
2724 1/4" x 2-1/4" 100 500 2786 2796 CAT.
2726 1/4" x 2-3/4" 100 500 2786 2796 NO. SIZE 2" 10
2728 1/4" x 3-1/4" 100 500 2787 2797 3" 10
2730 1/4" x 3-3/4" 100 500 2787 2797 2781 5/32" x 3-1/2" 4" 10
2732 1/4" x 4" 100 500 2787 2797 2" 10
2782 5/32" x 4-1/2"

2783 5/32" x 5-1/2"

2785 3/16" x 3-1/2"

2786 3/16" x 4-1/2" 3" 10

2787 3/16" x 5-1/2" 4" 10

2788 3/16" x 6-1/2" 5" 10

BLUE PERMA-SEAL™ TAPPER™ PHILLIPS FLAT HEAD 2789 3/16" x 7-1/2" 6" 10

STANDARD PACKAGING-100 SCREWS AND 1 DRILL PER BOX

CAT. STD. STD. DRILL REFERENCES

NO. SIZE BOX CTN. STRAIGHT SDS HEX

2740 3/16" x 1-1/4" 100 500 2781 2793

concrete 2742 3/16" x 1-3/4" 100 500 2781 2793 SDS HEX USABLE STD.
anchors 2744 3/16" x 2-1/4" 100 500 2782 2793 LENGTH TUBE
2746 3/16" x 2-3/4" 100 500 2782 2793 CAT.
2748 3/16" x 3-1/4" 100 500 2783 2794 NO. SIZE 3" 1
2750 3/16" x 3-3/4" 100 500 2783 2794 5" 1
2752 3/16" x 4" 100 500 2783 2794 2793 5/32" x 5" 3" 1
2760 1/4" x 1-1/4" 100 500 2785 2796 5" 1
2794 5/32" x 7"

2796 3/16" x 5"

2797 3/16" x 7"

2762 1/4" x 1-3/4" 100 500 2785 2796

specialty items 2764 1/4" x 2-1/4" 100 500 2786 2796
services & data
2766 1/4" x 2-3/4" 100 500 2786 2796

2768 1/4" x 3-1/4" 100 500 2787 2797

2770 1/4" x 3-3/4" 100 500 2787 2797

2772 1/4" x 4" 100 500 2787 2797

2774 1/4" x 5" 100 100 2788 -

2776 1/4" x 6" 100 100 2789 -

332
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

INSTALLATION TOOLS FOR 3/16" AND 1/4" TAPPER™

CAT. MAX SCREW MAX. BIT STD. safety
NO. DESCRIPTION LENGTH LENGTH BOX products

2791 TAPPER™ 1000 Tool (as shown) 4" 5-1/2" 1
( 8 0 0 ) 7 3 3 - 0 0 8 9 • ( 7287912*) 3C2ON9D-RI4VE0®0† 20000 • FA2X-3:/4 "( 7 8 14-1)/23" 2 6 - 417 5 7

2795 1000 SDS Extension (8") 6" 7-1/2" 1
MECHANICAL ANCHORS* This tool cannot be used with SDS Drill Bits or PFH screws.

tapper™ INSTALLATION TOOLS & ACCESSORIES STD. BOX TOOLS &
ACCESSORIES
TAPPER™ 1000 REPLACEMENT PARTS 1
1
CAT. NO. DESCRIPTION

2953 Drive Sleeve Assy. (5-3/4")
2964 Blue 3/16” Hex Wedge-Bolt® Socket

INSTALLATION TOOLS FOR 3/16" AND 1/4" TAPPER™ CONDRIVE®† 2000 REPLACEMENT PARTS CONTRACTOR
SUPPLIES
CAT. MAX SCREW MAX. BIT STD. CAT. NO. DESCRIPTION STD. BOX

NO. DESCRIPTION LENGTH LENGTH BOX 2956 1/4" Hex Key 1

2791 TAPPER™ 1000 Tool (as shown) 4" 5-1/2" 1 2957 5/16" Hex Key 1

2792* CONDRIVE®† 2000 2-3/4" 4-1/2" 1 † CONDRIVE® is a Registered Trademark of Illinois Tool Works.

2795 1000 SDS Extension (8") 6" 7-1/2" 1

* This tool cannot be used with SDS Drill Bits or PFH screws.

TAPPER 3000 TOOL KIT hangers
& strut
CAT NO. DESCRIPTION BOX CARTON

TAPPER™ 1000 REPLACEMENT PARTS NCIN5AOT8.S.6T5ALLDA3AHEST/se8CsxI"ReODImPcNrTobiIvnOlyeTcNrr(Oes(uatOemseLderwSiavisetFhcOsacotaRc.tk#.e3#5t/s581M87(b664Al"0u)XLe)1SEA)S/CN4lNReG"EeTDWvaHen1d/4"MLAETXNA.GBTPIHT1PER™ 10

CAT. NO. DESCRIPTION STD.
BOX
2953 Drive Sleeve Assy. (5-3/4")
STD. BOX 25789714 TASlPePeEveR™Ass1e0m0b0lyTool (as shown) 4" 5-1/2"1 1-
2964 Blue 3/16” Hex Wedge-Bolt® Socket
1 2792* CONDRIVE®† 2000 2-3/4" 4-U1S/A2B"LE ST1D. WT./
1 2C7A9T5NO. 1D0E0S0CRSIDPTSIOENxtension (8") 6" 7L-E1N/2G"TH TU1BE 10

*5T8h6i6s tool c1a/4n"noxt6b"eHuesxedShwanitkhSSDDSSDDrirlilllBBitits or PFH screws4." 1 1/2 fasteners &
threaded rod
TAPPER™ 1000 REPLACEMENT PARTS STD. BOX
CONDRIVE®† 2000 REPLACEMENT PARTS
CAT. NO. DESCRIPTION 1
CAT. NO. DESCRIPTION 1
2953 Drive Sleeve Assy. (5-3/4")

2964 Blue 3/16” Hex Wedge-Bolt® Socket

STD. BOX

2956 1/4" Hex Key 1 concrete
anchors
2957 5/16" Hex Key 1 Newman Associates Is Your
"One-Stop Shopping Source"
† CONDRIVE® is a Registered Trademark of Illinois Tool Works.

We're ConCsOtNaDnRtIlVyEA®†d2d0i0n0gRENPeLwACEPMroEdNTucPAtsRTTSo Our Inventory. specialty items
If You NC2eA9eT5. 6dNO.AnD1E/I4St"CeRHIPmeTxIOKNTeyhat Is Not Listed In This CaSTtDa. BlOo1Xg services & data

Be sure to call us!2957 5/16" Hex Key 1

† CONDRIVE® is a Registered Trademark of Illinois Tool Works.

333
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products Internally Threaded Expansion Anchor

MECHANICAL ANCHORSBASE MATERIAL
Concrete, Block, Brick, Pre-cast Hollow Core Plank, Stone

TOOLS & SIZE RANGE
ACCESSORIES
1/4" to 5/8"

SNAKE™ INTERNALLY THREADED SELF-TAZNaAmCHPaOcRPAMlAloITEyRNwIALitGh CaArboNn SCteeHl orOStaRinless Steel Cones

The Hollow-Set™ Dropin anchor is designed for anchoring in hollow base materials

csAuocnPhcraPesteLhpoIllaClonwkA.cITtocnIacOnreatNelsboSlobceku, bseridckinwsiothlidwbeaespehmoaletseraianlds.hollow core pre-cast
HAolNlowDmaUsoSnryEmSaterials often have a minimum outer wall thickness of 1-1/2".

D•uSrinugsptheenddrilnlinggCporoncdesusi,tspalling on the back side of the wall often decreases the
w•aCllathbicleknTersasyasvaailanbdleSfotrruatnchoring to 1" or less. The design of the Hollow-Set™
Internally Threaded Self-Tapping Anchor D•roPpiipneovSeurcpopmoerststhis problem.
•ZFAirMe ASCprBinOkDleYrsWITH CARBON STEEL CONE Snake+ SD
BASE MATERIAL Setting Tool

CONTRACTOR Concrete •CSATu. spended Lighting DRILL OVERALL SLEEVE STD. STD.
SUPPLIES
SIZE RANGE NO. SIZE DIA. LENGTH LENGTH BOX CTN.

1/4" and 3/8" diameter ASlN99l 33sAt23eK00eEl,+self51-t//a41p"6p"ing 3/8" 7/8" 5/8" 100 1000
bol5t /a8n"chor. 1-5/16" 15/16" 500
ANCHOR MATERIAL machine 15/16" 50 500
250
Carbon Steel 9340 3/8" 5/8" 1-5/16" 1-SB1TOD/X4. " STD. 50 125
CTN.
The Snake+ anchor is an all-steel, internally threaded, self-tapping screw anchor 9CA3T5. N0O. 1/2" DESCRIPTION 3/4" 1-3SI/Z4E" 50
designed for use in cracked and uncracked concrete and is suitable for overhead
anchoring applications.The Snake+ design allows for shallow embedment and can 96430610SD 5/S8N"AKE+ Internally Thre1a"ded 3/82"" 1-510/2" 500 25
be installed in normal-weight concrete, structural sand-lightweight concrete and
concrete over metal deck. The Snake+ screw anchor is installed with a power tool 6407SD SNAKE+ SD Setting Tool 3/8" 1 -
and Snake+ setting tool and mechanically interlocks with the base material. ZAMAC BODY WITH STAINLESS STEEL CONE
A hammer is not required for installation.

CAT. DRILL OVERALL SLEEVE STD. STD.

hangers HOLLOW-SET™ DROPINSN94OA.20NDS1I/Z4E"SETTING3D/8IA".TOLOEN7G/8LT"H LENGTH BOX CTN.
& strut
5/8" 100 1000

9440 3/8" 5/8" 1-5/16" 15/16" 100 500

Internally Threaded Expansion Anchor For solid base materials
SETTING TOOLS - SOLID BASE MATERIALS
BASE MATERIAL
fasteners & CAT. STD. STD.
threaded rod Concrete, Block, Brick, Pre-cast Hollow Core Plank, Stone NO. SIZE BOX CTN.

SIZE RANGE 9322 1/4" 11

1/4" to 5/8" 9342 5/16" & 3/8" 1 1

ANCHOR MATERIAL 9352 1/2" 11

Zamac Alloy with Carbon Steel or Stainless Steel Cones 9362 5/8" 11

concrete The Hollow-Set™ Dropin anchor is designed for anchoring in hollow base materials For hollow base materials
anchors such as hollow concrete block, brick with weep holes and hollow core pre-cast
concrete plank. It can also be used in solid base materials.
Hollow masonry materials often have a minimum outer wall thickness of 1-1/2".
During the drilling process, spalling on the back side of the wall often decreases the
wall thickness available for anchoring to 1" or less. The design of the Hollow-Set™
Dropin overcomes this problem.

ZAMAC BODY WITH CARBON STEEL CONE SETTING TOOLS - HOLLOW BASE MATERIALS

CAT. DRILL OVERALL SLEEVE STD. STD. CAT. STD. STD.
NO. SIZE DIA. LENGTH LENGTH BOX CTN. NO. SIZE BOX CTN.

9320 1/4" 3/8" 7/8" 5/8" 100 1000 9323 1/4" 11
50 500
9330 5/16" 5/8" 1-5/16" 15/16" 50 500 9333 5/16" 11
50 250
9340 3/8" 5/8" 1-5/16" 15/16" 25 125 9343 3/8" 11

specialty items 9350 1/2" 3/4" 1-3/4" 1-1/4" 9353 1/2" 11
services & data
9360 5/8" 1" 2" 1-1/2" 9363 5/8" 11

ZAMAC BODY WITH STAINLESS STEEL CONE

CAT. DRILL OVERALL SLEEVE STD. STD.
NO. SIZE DIA. LENGTH LENGTH BOX CTN.

9420 1/4" 3/8" 7/8" 5/8" 100 1000
100 500
9440 3/8" 5/8" 1-5/16" 15/16"

334 SETTING TOOLS - SOLID BASETMHAETECROIAFNLoSrSsToRlidUbCasTeImOaNterSiaUlsP P LY S P E C I A L I S T . . . W H E R E S E R V I C E C O M E S F I R S T

CAT. STD. STD.

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
MECHANICAL ANCHORS

STEEL DROPINS AND SETTING TOOL

TYPE 303 STAINLESS STEEL DROPIN TOOLS &
ACCESSORIES
CAT. DRILL MIN. THREAD STD. STD.
NO. SIZE DIA. DEPTH DEPTH BOX CTN.

Internally Threaded Expansion Anchor 6204 1/4" 3/8" 1" 7/16" 100 1000

BASE MATERIAL 6206 3/8" 1/2" 1-9/16" 5/8" 50 500
6208 1/2" 5/8" 2" 13/16" 50 250
Solid Concrete, Solid Block, Hard Stone 6210 5/8" 7/8" 2-1/2" 1-3/16" 25 125
6212 3/4" 1-3/8" 10 50
SIZE RANGE 1" 3-3/16"
THREAD STD. STD.
1/4" to 3/4" Standard Thread, 1/2" & 3/4" in Coil Thread DEPTH BOX CTN.

ANCHOR MATERIAL TYPE 316 STAINLESS STEEL DROPIN 7/16" 100 1000 CONTRACTOR
5/8" 50 500 SUPPLIES
Carbon Steel and Type 303 or 316 Stainless Steel 13/16" 50 250
1-3/16" 25 125
The Steel Dropin is an all-steel, machine bolt anchor available in carbon steel and CAT. DRILL MIN.
NO. SIZE DIA. DEPTH
two types of stainless steel. It can be used in solid concrete, hard stone, and solid
6224 1/4" 3/8" 1"
block. A coil-thread version for forming applications is also available. A setting tool is
also available in each standard carton. 6226 3/8" 1/2" 1-9/16"

CARBON STEEL DROPIN (SMOOTH WALL) 6228 1/2" 5/8" 2"

CAT. DRILL MIN. THREAD STD. STD. 6230 5/8" 7/8" 2-1/2"

NO. SIZE DIA. DEPTH DEPTH BOX CTN.

6304 1/4" 3/8" 1" 7/16" 100 1000 CARBON STEEL COIL THREAD DROPIN
6306 3/8" 1/2" 1-9/16" 5/8" 50 500
6308 1/2" 5/8" 2" 13/16" 50 250 CAT. DRILL MIN. THREAD STD. STD.

NO. SIZE DIA. DEPTH DEPTH BOX CTN. hangers
& strut
6320 5/8" 7/8" 2-1/2" 1-3/16" 25 125 6330 1/2" 5/8" 2" 13/16" 50 250

6312 3/4" 1" 3-3/16" 1-3/8" 10 50 6332 3/4" 1" 3-3/16" 1-3/8" 10 50

CARBON STEEL FLANGED DROPIN (LIPPED) Use Setting Tool Cat. No. 6309 for 1/2" size, Cat. No. 6313 for 3/4" size.

CAT. DRILL MIN. THREAD STD. STD.

NO. SIZE DIA. DEPTH DEPTH BOX CTN.

6324 1/4" 3/8" 1" 7/16" 100 1000

6326 3/8" 1/2" 1-9/16 5/8" 50 500 InStEeTrnTIaNllGyTTOhOreLaSdFeOdR ESxTpEEaLnsDioRnOPAINncAhNoCrHORS fasteners &
6328 1/2" 50 250 threaded rod
5/8" 2" 13/16" CBAATS.E MATERIAL STD. STD.
CTN.
CARBON STEEL KNURLED WALL DROPIN NPrOe. -cast HSoIZllEow Core Plank, CoBnOcXrete
6SI3ZE05RANGE 1/4" 1 250
CAT. ROD/ANCHOR OVERALL THREAD STD. STD.
613/40”7, 3/8"3a/8n"d 1/2” 1 100
NO. SIZE LENGTH DEPTH BOX CTN.

6340 1/4" 1" 7/16" 100 1000 A6N3C0H9OR MA1TE/2R"IAL 1 100
6342 3/8" 1-9/16" 5/8" 50 250 1 50
C63a1rb1on St5e/e8l"

6344 1/2" 2" 13/16" 50 250 Th6e3M13ini Dro3p/4in" is a carbon steel, m1achine bol2t5anchor used in shallow embedment

applications. It can be used in solid concrete and hollow core concrete plank, and

MINI DROPINS ANDiatpcpalniScabEteiouTnsse.TdIinNhaGrd sTtonOe aOnd Lsolid block. It may also be used in overhead

CAT. DRILL MIN. THREAD STD. STD. concrete
NO. anchors
SIZE DIA. DEPTH DEPTH BOX CTN.
6335
6322 1/4" 3/8" 5/8" 3/8" 100 1000
6337 3/8"
Internally Threaded Expansion Anchor 1/2" 1/2" 3/4" 13/32" 100 1000

BASE MATERIAL 5/8" 1" 5/8" 50 250

Pre-cast Hollow Core Plank, Concrete SETTING TOOLS STD. STD. specialty items
BOX CTN. services & data
SIZE RANGE CAT.
NO. SIZE 1 50
1/4”, 3/8" and 1/2” 1 50
6336 1/4" 1 50
ANCHOR MATERIAL
6323 3/8"
Carbon Steel
6338 1/2"
The Mini Dropin is a carbon steel, machine bolt anchor used in shallow embedment
applications. It can be used in solid concrete and hollow core concrete plank, and
it can be used in hard stone and solid block. It may also be used in overhead
applications.

CAT. DRILL MIN. THREAD STD. STD.
NO.
SIZE DIA. DEPTH DEPTH BOX CTN.
6335
6322 1/4" 3/8" 5/8" 3/8" 100 1000 335
6337 3/8"
1/2" 1/2" T H E3/C4"O N S13T/3R2"U C T1I0O0 N S1U000P P LY S P E C I A L I S T . . . W H E R E S E R V I C E C O M E S F I R S T

5/8" 1" 5/8" 50 250

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
MECHANICAL ANCHORS

VERTIGO™ ROD HANGER SYSTEMS

TOOLS & Rod Hanger System WOOD VERTICAL HANGER
ACCESSORIES
BASE MATERIAL
CAT NO. ROD SCREW SHANK POINT BOX CARTON
Steel, Wood, Concrete SIZE SIZE & LENGTH STYLE
100 500
SIZE RANGE 7163 1/4” 1/4” x 2” Type 17 100 500
Type 17 100 500
CONTRACTOR 1/4” – 1/2” 7203 3/8” 1/4” x 1” Type 17 100 500
SUPPLIES Type 17 100 500
ANCHOR MATERIAL 7165 3/8” 1/4” x 2” Type 17 100 500
Type 17 100 500
Carbon Steel 7167 3/8” 1/4” x 3” Type 17

PRODUCT DESCRIPTION 7169 3/8” 1/4” x 4”

jCoaisVVsccctirimtobVosnomnutaooherfeetoeffeasiruensalncserre1n“tpaurn1msptteottactd/iicmramssbdae/ilerggm4loagr4eclerepaVntaeooas”nttiost”hmtrpa,aeedtnt.iesdrewiinailrarrtiidassFeoessnoitiansbso,adVonrnianaagptngbeadeVlrrndedawdslrdioenawseorsvliaeeo3laeao3tocmitrenedldtnSiin/ethlmtln/tgr8dleioecso8heeus.gsltro-al”sycofo-o”ltsuiaops,fa”psenkscftdeidndiwpdeazehiekeicrsemiadisetslriaesrenacocoacoe.tatenadDormgvcnesoemsvaeF,nladotd,crndsioidewsaaaidedrnlreaoevturotieneltnfe.eeleelrerwmldatgtadosdCtearrhseprsyulafoltnmsrlosesitfrhsenrbosiebeohotossnrddtaeeeed.ertaefodrpcoaemeleeeaIlderurcmernsaVdetlcemtmlormlrjshnhlhodeiottawtelvirhseidouaarrnhmeitnemesbetreonummrraVisaetomaaeegrosbdnstndedainmtdaaooadltdeshirredaiswnedlctlieienlessdlnfediakdaseclsagatordrddeteno.tiydofnsonoaefdiatValdlotaredrmbuslcddrrsesfelonsoilpeemasstnlauforbtVdtledtedaoostewoendueenseiinmtsmrwngnrdieaewnrsiipsnoilotton.blnmsetn,a“hirgihn,nggIbltreoatgscrnisatheweteoaoratsvao,somdsryrsstwstintoyaeafdsel.yajehseajsmioosdclsVoeeotmhbetsrtidimilofeeiweoVseoenetpsopabmredtrwnmeuatsfertrsaipnrastoindrtl,laa,gcaldoptrelefgpasrfmitnocolnrrrioagtltuelboiosdraawlelsraoer,nyelptlroluslr”siascSeroeoruitm,ionlodeamnnrspislnectpcnuhoitoeklnsheasmawedb.tnslamatlaenaeiednz.lDsrsmvdliedeanearadetwigrvnirioeeidtdntrhyriisll 7162 3/8” 3/8” x 2-1/2”

7164 1/2” 3/8” x 2-1/2”

hangers STEEL VERTICAL HANGER WOOD SIDE HANGER
& strut
ROD SCREW SHANK POINT ROD SCREW SHANK POINT
SIZE & LENGTH STYLE SIZE SIZE & LENGTH STYLE
CAT NO. SIZE BOX CARTON CAT NO. BOX CARTON
#3 Type 17
#3 FOR PURLINS #3 100 500 7185 1/4” 1/4 x 1” Type 17 100 500
#3 100 500 Type 17 100 500
7155 1/4” 1/4-20 x 1” #3 100 500 7205 3/8” 1/4 x 1” Type 17 100 500
#3 100 500 100 500
7157 3/8” 1/4-20 x 2” 100 500 7170 3/8” 1/4 x 2”
#5
7158 3/8” 1/4-20 x 1” (w/nuts) #5 100 500 7156 3/8” 3/8 x 2-1/2”
#5 100 500
7159 3/8” 1/4-20 x 1-1/2” 100 500

fasteners & 7160 3/8” 1/4-20 x 1-1/2” (w/nuts)
threaded rod
#5 FOR BEAMS

7152 1/4” 12-24 x 1-1/2”

7154 3/8” 12-24 x 1-1/2” (w/nuts)

7161 1/2” 12-24 x 1-1/2” (w/nuts) CONCRETE VERTICAL HANGER

ROD SCREW SHANK POINT
STYLE
CAT NO. SIZE SIZE & LENGTH BOX CARTON

7171 1/4” 1/4 x 1-1/4” ANSI WB thread 100 500

7173 3/8” 1/4 x 1-1/2” ANSI WB thread 100 500

STEEL SIDE HANGER 7175 1/2” 3/8 x 2-3/4” ANSI WB thread 50 250

concrete ROD SCREW SHANK POINT BOX CARTON For Side Mount Concrete Applications use Cat. No. 7185 and 7170 with a 1/4”
anchors CAT NO. SIZE SIZE & LENGTH STYLE ANSI Drill Bit
#3 FOR PURLINS 100 500
100 500
7183 1/4” 1/4-20 x 1” #3 100 500 VERTIGO™ ACCESSORIES
100 500
7184 3/8” 1/4-20 x 1” (w/nuts) #3

7186 3/8” 1/4-20 x 1-1/2” (w/nuts) #3

7188 3/8” 1/4-20 x 2” (w/nuts) #3

specialty items #5 FOR BEAMS 12-24 x 1-1/2” #5 50 250
services & data 100 500
7200 1/4” 12-24 x 1-1/2” (w/nuts) #5 DRIVER SOCKET
7201 3/8”

CAT NO. DESCRIPTION COLOR BOX CARTON

7187 Universal Steel & Wood Socket Red 5 25
5 25
POLE TOOL 7195 1/4” Concrete Socket Blue 5 25
5 25
CAT NO. DESCRIPTION 7197 3/8” Concrete Socket Blue

7166 6’-12’ Pole Tool (includes three Jaw Chuck) BOX CARTON 7198 1/2” Concrete Socket Blue

11

336
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
MECHANICAL ANCHORS

BANG-IT CONCRETE INSERTS

WOOD-KNOCKER CONCRETE INSERTS TOOLS &
ACCESSORIES
Concrete Inserts
Concrete Inserts CONTRACTOR
BASE MATERIAL SUPPLIES
BASE MATERIAL
Concrete, Lightweight Concrete hangers
Concrete, Lightweight Concrete & strut
SIZE RANGE
SIZE RANGE
1/4” to 7/8”
1/4” to 3/4”
ANCHOR MATERIAL
ANCHOR MATERIAL
Carbon Steel and Engineered Plastic
Carbon Steel and Engineered Plastic
Bang-It Concrete Inserts are designed for installation through pre-drilled metal
composite deck (i.e. “pan deck”) used to support a newly poured concrete floor or Wood-Knocker Concrete Inserts are installed onto wooden forms used to support a
roof slab. Depending upon the size/color chosen, the protective sleeve protrudes newly poured concrete floor slabs, roof slabs or walls. When the forms are stripped,
below the surface of the deck allowing overhead attachment of steel threaded rod the color-coded flange is easily seen embedded in the concrete surface allowing
in sizes ranging from 1/4” to 7/8” in diameter. The protective sleeve prevents attachment of steel threaded rod or threaded bolts in sizes ranging from 1/4” to
sprayed fireproofing material and acoustical dampening products from clogging the 3/4” in diameter. The unique six-sided impact plate offers resistance to rotation
internal threads of the insert inside, as well as burying, masking or losing the insert within the concrete as a steel threaded rod or threaded bolt is being installed.
location. The unique, six-sided impact plate offers resistance to rotation within the
concrete as a steel threaded rod is being installed.

CAT. DESCRIPTION PRE DRILLED STD. PALLET CAT. STD. PALLET
NO. HOLE BOX QTY. NO. DESCRIPTION BOX QTY.

7540 1/4” Brown Bang-It™ 13/16” 100 4000
7542 100 4000
7544 3/8” Green Bang-It™ 13/16” 100 4000 7550 1/4” Brown Wood Knocker™ 200 9600
7546 50 2400
1/2” Yellow Bang-It™ 13/16” 7552 3/8” Green Wood Knocker™ 200 9600
7548 50 2400
7549 5/8” Red Bang-It™ 1-3/16” 50 2400 7554 1/2” Yellow Wood Knocker™ 200 9600
7560 1
7562 3/4” Purple Bang-It™ 1-3/16” 1 7556 5/8” Red Wood Knocker™ 150 6000
7564 1
7566 7/8” Black Bang-It™ 1-3/16” 1 7558 3/4” Purple Wood Knocker™ 150 6000 fasteners &
7567 1/2” Coil Thread WK 200 9600 threaded rod
Bang-It Deck Driller
7568 3/4” Coil Thread WK 150 6000
13/16” Carbide Hole Saw for 1/4”, 3/8” and 1/2”
1-3/16” Carbide Hole Saw for 5/8”, 3/4” and 7/8” 1/2” and 3/4” coil thread Wood-Knockers are available upon request for
Framing Applications.
Carbide Hole Saw Center Bit

SPIKE™ PRE-EXPANDED ANCHORS

MUSHROOM HEAD TYPE 316 STAINLESS STEEL SPIKE®

CAT. DRILL MIN. STD. STD. concrete
anchors
NO. SIZE DIA. EMBED. BOX CTN.

Pre-Expanded Anchor 6602 3/16" x 1" 3/16" 7/8" 100 1000

BASE MATERIAL 6603 3/16" x 1-1/4" 3/16" 7/8" 100 1000

Concrete, Block 6604 3/16" x 1-1/2" 3/16" 1-1/4" 100 1000

SIZE RANGE 6606 3/16" x 2" 3/16" 1-1/4" 100 1000

3/16" x 1" to 1/2" x 6-1/2" 6623 1/4" x 1-1/4" 1/4" 1" 100 1000

ANCHOR MATERIAL 6624 1/4" x 1-1/2" 1/4" 1-1/4" 100 1000

Carbon Steel and Type 316 Stainless Steel 6626 1/4" x 2" 1/4" 1-1/4" 100 1000 specialty items
services & data
The SPIKE® anchor is a patented, one-piece, tamper-proof anchor for use in concrete, 6628 1/4" x 2-1/2" 1/4" 1-1/4" 100 1000
block, brick or stone. Several head styles are available and offered in Carbon and Type 316
Stainless Steel. The SPIKE® anchor is formed with an "s" shaped configuration 6630 1/4" x 3" 1/4" 1-1/4" 100 1000
at the working end of the anchor to create an expansion mechanism.
Since the anchor is pre-expanded, there is no secondary tightening operation. 6646 3/8" x 2" 3/8" 1-3/4" 25 250

6648 3/8" x 2-1/2" 3/8" 1-3/4" 25 250

6650 3/8" x 3" 3/8" 1-3/4" 25 250

The published length is measured from below the head to the end of the anchor.

337
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
MECHANICAL ANCHORS

SPIKE® PRE-EXPANDED ANCHORS

TOOLS & MUSHROOM HEAD GRADE 8.2 CARBON STEEL SPIKE® SPECIAL APPLICATION
ACCESSORIES SPIKE ANCHORS
CAT. DRILL MIN. STD. STD.

NO. SIZE DIA. EMBED. BOX CTN.

5502 3/16" x 1" 3/16" 7/8" 100 1000

5503 3/16" x 1-1/4" 3/16" 7/8" 100 1000

5504 3/16" x 1-1/2" 3/16" 1-1/4" 100 1000

5506 3/16" x 2" 3/16" 1-1/4" 100 1000 ROD HANGING

5508 3/16" x 2-1/2" 3/16" 1-1/4" 100 1000 PIPE SPIKE® GRADE 8.2 CARBON STEEL

CONTRACTOR 5510 3/16" x 3" 3/16" 1-1/4" 100 1000 CAT. HEAD DRILL MIN. STD. STD.
SUPPLIES NO. SIZE DIA. EMBED. BOX CTN.

5511 3/16" x 3-1/2" 3/16" 1-1/4" 100 1000 3755 1/4" 3/16" 1-1/4" 100 1000
50 500
5512 3/16" x 4" 3/16" 1-1/4" 100 500 3758 3/8" 1/4" 1-3/4"

5522 1/4" x 1" 1/4" 7/8" 100 1000

5523 1/4" x 1-1/4" 1/4" 1" 100 1000

5524 1/4" x 1-1/2" 1/4" 1-1/4" 100 1000

5526 1/4" x 2" 1/4" 1-1/4" 100 1000

5528 1/4" x 2-1/2" 1/4" 1-1/4" 100 1000 SUSPENDED CEILINGS

5530 1/4" x 3" 1/4" 1-1/4" 100 1000 TIE-WIRE SPIKE® GRADE 8.2 CARBON STEEL

5531 1/4" x 3-1/2" 1/4" 1-1/4" 100 1000 CAT. DRILL MIN. TIE-WIRE STD. STD.
NO. SIZE DIA. EMBED. HOLE SIZE BOX CTN.
5532 1/4" x 4" 1/4" 1-1/4" 100 1000
hangers 3756 3/16" 3/16" 1-1/4" 3/16" 100 500
& strut 5546 3/8" x 2" 3/8" 1-3/4" 25 250 100 500
3759 1/4" 1/4" 1-1/4" 9/32"
5548 3/8" x 2-1/2" 3/8" 1-3/4" 25 250

5550 3/8" x 3" 3/8" 1-3/4" 25 250

5551 3/8" x 3-1/2" 3/8" 1-3/4" 25 250

5552 3/8" x 4" 3/8" 1-3/4" 25 250 CONCRETE FORMING

5554 3/8" x 5" 3/8" 1-3/4" 25 250 FORMING SPIKE® GRADE 8.2 CARBON STEEL

5556 3/8" x 6" 3/8" 1-3/4" 25 250 CAT. ANCHOR DRILL MIN. STD. STD.
NO. SIZE DIA. EMBED. BOX CTN.
fasteners & 5569 1/2" x 2-3/4" 1/2" 2-1/2" 50 200
threaded rod 3795 3/16" x 1-1/2" 3/16" 1-1/4" 100 1000
5571 1/2" x 3-1/2" 1/2" 2-1/2" 50 150 1000
3796 3/16" x 2" 3/16" 1-1/4" 100 1000
5572 1/2" x 4" 1/2" 2-1/2" 25 150 1000
3797 3/16" x 2-3/4" 3/16" 1-1/4" 100
5574 1/2" x 5" 1/2" 2-1/2" 25 150
3794 1/4" x 2-3/4" 1/4" 1-1/4" 100
5577 1/2" x 6-1/2" 1/2" 2-1/2" 25 150

The published length is measured from below the head to the end of the anchor. SPIKE® INSTALLATION TOOLS

concrete FLAT HEAD GRADE 8.2 CARBON STEEL SPIKE® While the SPIKE® anchor can easily be installed using a hammer, a specially
anchors designed series of drivers and manual tools provide a fast, easy to use method for
installing SPIKE® anchors into concrete and masonry materials. The tools allow
SPIKE® anchors to be installed in confined areas and prevent damage to the fixture
from stray hammer blows.

CAT. DRILL MIN. STD. STD.
CTN.
NO. SIZE DIA. EMBED. BOX
1000
5608 3/16" x 2-1/2" 3/16" 1-1/4" 100 1000
1000
5610 3/16" x 3" 3/16" 1-1/4" 100 1000 CAT. TOOL GUIDE STD.
1000 NO. DESCRIPTION I.D. BOX
5612 3/16" x 4" 3/16" 1-1/4" 100 1000
1000 3790 SPIKE® Driver 1000 1/2" 1
5624 1/4" x 1-1/2" 1/4" 1-1/4" 100 1000 3791 SPIKE® Driver 2000 1/2" 1

specialty items 5626 1/4" x 2" 1/4" 1-1/4" 100 500
services & data
5628 1/4" x 2-1/2" 1/4" 1-1/4" 100

5630 1/4" x 3" 1/4" 1-1/4" 100

5631 1/4" x 3-1/2" 1/4" 1-1/4" 100

5632 1/4" x 4" 1/4" 1-1/4" 100 PIPE SPIKE® TOOL

The published length is the overall length of the anchor. CAT. TOOL TIP STD.
NO. DESCRIPTION O.D. BOX

3760 Pipe SPIKE® Setting Tool 5/16" 1

338
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
MECHANICAL ANCHORS

Anchor Category Metal Plastics TOOLS &
Product ACCESSORIES
Wall-Dog
Scru-Lead CONTRACTOR
Toggle-Bolt SUPPLIES
Polly
Legs
Sharkie
Strap-Toggle
Zip-It

(Also Available in Zinc)

Zip-Toggle
Poly-Toggle
Pop Toggle
Bantam Plug
Fluted Plastic

Concrete n n n non n

Lightweight Concrete o o n ooo o

Hollow Core Plank n o n o nn ooo o

Base Material Grout-filled Concrete Masonry n o n ooo o

Hollow Concrete Masonry n o n n on noo o

Solid Brick n n n oon o

Hollow Brick o o o oo ooo o

Stone o n oo hangers
& strut
Structural Clay Tile oo oo oo

Plywood n nn oo on

Wallboard /Plaster n nnn on n n n n n o

No. 4 Screw n n

No. 5 Screw n n

No. 6 Screw n nn nn nnnn

No. 7 Screw n nn n nnn n

No. 8 Screw n nn n nnn n fasteners &
threaded rod
Anchor Diameter No. 9 Screw n nnnn

No. 10 Screw n nn nn n

No. 12 Screw n nn nn n

No. 14 Screw n nn nn

No. 16 Screw n n

No. 18 Screw n

1/8" n n

3/16" nn n

1/4" n nn n

5/16" n concrete
anchors
3/8" n n

1/2" n n

Coating/ Finished (Hex) Head nn
Material Head Style
Round Head n

Flat Head (Countersunk) nn

Mushroom Head n nn

Removable n n specialty items
services & data
Coated / Plated Carbon Steel n nnn n

Zamac Alloy n

Nylon / Plastic nn n n n n n n

Lead n

n - Suitable
o - May Be Suitable

339
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
MECHANICAL ANCHORS

TOOLS & WALL-DOG™
ACCESSORIES
Universal Light-Duty Anchor

SIZE RANGE WAZLILP-D-OIGT™™LIGHT DUTY ANCHOR - OVAL HEAD

3/16” Diameter x 1-1/4”Length CAT STD. STD. MASTER
NO. DESCRIPTION BOX CTN. CARTON
BASE MATERIAL
2314 1-1/4”Chrome Oval Head 100 1000 N/A
Wallboard (1/2”, 5/8” & double wallboard), Plywood, Concrete, Hollow or Grout
Filled Block, Brick, Plaster

ANCHOR MATERIAL 2328 1-1/4” White Oval Head 100 1000 N/A
2388 1-1/4” Black Oval Head 100 500 N/A
Case Hardened Steel

The Powers Wall-Dog™ is the industry’s first all steel one-piece screw anchor, which 2329 1-1/4” Brass Oval Head 100 500 N/A

CONTRACTOR fbeaasWteurAmeLsaLthe-irgDiahOl-sp.GrIot™sfildLeeItGehprHecTaudtDtsinUfogTr, YceoaArskyNscfaCresHtweO-nliiRkneg-tihOnrtVeoaAwdLsalplHbrooEvaAirddDeafnodr other masonry Wallboard Anchor
SUPPLIES smooth entry and
a pNCAoOT.werful hDoElSdC,RaIPnTdIONwhen removed the Wall-SBDTODoX.g leaves CaSTTNDm.. uch smMCaAlAlReSTrTOEhNRole than
or Grout tog23g1le4s or ot1h-e1r/4s”ysCthermoms.eFoOrvfaalsHteenading into wa1l0lb0oard or w1o0o0d0, no prNe-/Adrilling is
req2u3i2re8d. Fas1t-e1n/i4n”gWinhtoitecoOnvcarleHtee,ahdollow or gr1o0u0t filled blo1c0k0, 0brick anNd/Aplaster BASE MATERIAL
mhoaorsr,oGwnrrohyuicth
entry and req2Wu3i8rAe8sLLa-pDr1eO--1dG/r4™il”leLBdIlGa3c/Hk1T6O”vDaAlUNHTSeYIahdAolNe.CHOR 1-0O0VAL HEA5D00 N/A Wallboard
hole than
FNC2WEAO3AT.A2TU9LRLES-DAND1ODE-1GSBC/E4™RN”IPELTFBIIIOTrGaSNsHsTOvDaUl HTeYadANCHOR SB-1TO0WDX.0AFER HCSETT5NDA0.. D0 MNCAA/ARSTTOENR SIZE RANGE
mahliasontsreg,orwnisrhyich
entry and Use with No. 6 or No. 8 screw
hole than
ling is •C2AI3nT1st4alls in1w-1a/l4lb”oCahrrdo,mpelyOwvoaoldH,ecaodncrete, hoS1lTlDo0.0w or grouS1tT0Dfi0.ll0ed blocNk,/AMASTER ANCHOR MATERIAL
aosrteGr rout
l hold Engineered Nylon or Zamac Alloy

hor, which N2Ob3.r2ic8k andD1Ep-S1lCa/Rs4It”PeTrWIONhite Oval Head B1O0X0 C1TN0.00 N/CAARTON The Zip-It® anchor is a one piece self drilling anchor designed for use in hollow
mlahsoolndry
•222P37a87t8ented1/1d4-e”1sx/i4g1”n-1Bp/l2rao”cvkWidOhevitsaelfWoHraefsaemdr Hoeoatdh entry,11c00l0e0an cuttin5g050a0n0d a powN/eArNfu/Al hold CWATgZAayLpmLsau-cDmaOwllGoay™llbfLooIraGurHdseTfowDriUltihgTheYtitdhAueNtryCalHoNaOodR.s6.S-TItoDP.risANaNov.aH8ilEasAbcSlTrDeeD.winsbinot3h/8en"gtione1e"rewdanllybloonaradn. d
entry and
hole than hangers •22T23h72r8e9ad d1e/14s-i”1g/xn4”2p”rBeWrvaehsnistetOsWvsaplfienHrneHianedagdand stripp1i1n000g0 505000 N/AN/A
ling is & strut
aster •22H7e9at tre1a/4te”dx p2o-1i/n4t”pWehniteetWraatefesr Hmeeadtal and1w00ood stud5s00 N/A NO.The ZipD-EItS®CRIPJTr.IOisNformed from engineeBreOdX nylon foCrTNu.se with No. 6 screws in 3/8" to

•2T2w80o finis1h/4e”dxhe2-a1d/2s,”oWvahilteanWdafperaHnead 100 500 N/A 23156/8" w1a-l1lb/4o”aCrdh.rome Pan Head 100 1000 N/A

• Two colors, chrome & white head 2330 1-1/4” White Pan Head 100 1000 N/A
• WSeAlf-LdLril-lDs oOwGn™smLIaGllHhToleDiUn TwYallAboNaCrdHOR - OVAL HEAD
2273 1-1/2” White Pan Head 100 500 N/A
• CIAnTstalls quickly and easily with a Phillips® sScTDre. wdriver STD. MASTER 500 STDN./A
NO. DESCRIPTION BOX CTN. CARTON 2274CAT. 1-1/2”WABLrLonze Pan Head 100 500 BONX/A STD.
2275NO. 1-1/2”THZICinKcNPESaSn HeadDESCRIPTION 100 CTN.
C22WA33T21A84LL-D11O--11G//44™””CLWhIGhroitHmeTeOOvDavUlaHlTHeYaedaAdNCHORS11-T00DP00. AN HEA1S1T0D0D00.00 N/A
N/A 2276NYLO1-1N/2Z”IBPla-cIkT®Phosphate Pan Head 100 500 N/A
N/A 500 10N0/A 1000
N2O3.88 D1E-1SC/4RI”PTBIOlaNck Oval Head B1O0X0 CT5N0. 0 228623451-1/4”3/B8l"actkoP1a"n HeaSdtd. box, no s1c0re0ws

fasteners & 232196 1-1/4”CBhrarossmOevPaalnHHeaedad 110000 1050000 N/A 229423481-1/4”3/B8r"astsoP1a"n HeaSdtd. box, No.180x01"screws500 10N0/A 1000
threaded rod
2330 1-1/4” White Pan Head 100 1000 N/A 2355 3/8" to 1" Master ctn., no screws - 5000
N/A
2W27A3LL-D1O-1G/2™”LWIGhiHteTPaDnUHTeYadANCHOR1-0P0AN HEAD500 ZINC ZIP-IT®

C2A2T74 1-1/2” Bronze Pan Head S1T0D0. ST5D0. 0 N/A 2346 3/8" to 1" Std. box, no screws 100 1000
N222222O332222.137778603566 D111111E------S111111C//////442R224I””””””PCTWWZBBIhOillnaarhhNoccciittmkkePeeaPPPPnhaaPanonnaHsnHepHHaehHeedaaaaedtddaedPan Head B111111O000000X000000 C11T005555N000000. 000000 NNNNNN//////AAAAAA Std. box, No.8 x 1"screws 100 1000
NN//AA 2349 3/8" to 1" Master ctn., no screws
550000 - 1000
2356 3/8" to 1"

22227944 11--11//24”” BBrroasnszePaPnanHeHaedad 110000 ZIP-IT® KITS

2275 1-1/2” Zinc Pan Head 100 500 N/A 2368 Nylon 50 Anchors , No. 8 x 1" screws, 1 10

2276 1-1/2” Black Phosphate Pan Head 100 500 N/A & No. 2 Phillips Driver Bit

l hold 2286 1-1/4” Black Pan Head 100 500 N/A 2369 Zinc 50 Anchors & No. 8 x 1" screws 1 10
concrete N/A & No. 2 Phillips Driver Bit
anchors 2W29A4LL-D1O-1G/4™”LBIrGasHs TPaDnUHeTaYd ANCHOR1-0P0AN HEAD500

NCWAOT.ALL-DDOESGCR™IPLTIIOGNHT DUTY ANCHORSB-TODCX. OMBO CSHTTNDW.. H WALCLAT-.DOG™ WKAILTLS STD. STD.
BOSTXD. CTN.
C2A3T16 1-1/4”Chrome Pan Head S1T0D0. 1ST0D0. 0 N/AMASTER CAT. NO. THICKNESS DESCRIPTION STD.
N2O3.30 D1E-S1C/R4I”PTWIOhNite Pan Head B1O0X0 C1T0N0. 0 N/ACARTON CTN. 1000
22226753 W1-a1l/l-2D”oWg ChiotemPbaonHHWeaHdChrome 100 N/A5000 NO. DESCRIPTION BOX 1000
500 N/AN/ A 10
1005000 N/A5000 2289NYLWOaNll-DZoIgPK-IitTwJitRh .Screwdriver 1 100 1000
N/A N/ A • 110P0HCI3LH/LR8IPO"SM-®5E S/P8CAR"NEHWEDARDIVASENtRdC.HBOoRSx 10010 1000
22227714 W1-a1l/l-2D”oBgrConozmebPoanHWHeHadChrome 110000 500 N/A 2350 • (No screws) 5000
SNTD/A. 100
22228715 11--11//42””CZhirnocmPeaRnobHeertasdon Head 100 23322351Wall-D3o/g8"K-i5t /w8i"th DrillSBtidt. Box, No. 6 x 1" screw1s 100 10
CTN. • 100 CHROME PANHEAD ANCHORS
specialty items 22226766 11--11//42””CBhlraocmkePRhoobseprthsoanteHPeaadn Head 110000 1005000 -
services & data 10 ZINC• 3Z/1I6P”-SITTRAJIGRH.T SHANK BIT
W22A86LL-DO1-G1/™4”KBIlTaSck Pan Head 100 500 1
10 2362 3/8"-5/8" Std. Box (No screws)
C2A2T9. 4 1-1/4” Brass Pan Head 100 ST5D0.0
STD. 2364 3/8"-5/8" Std. Box, No. 6 x 1" screws
NO. DESCRIPTION BOX CTN.

2289 Wall-Dog Kit with Screwdriver 1 2363 3/8"-5/8" Master Ctn. (No screws)

• 100 CHROME PANHEAD ANCHORS 1 ZIP-IT JR. KITS

2W3A32LL-DOW• 1aGlPl™-HDILKoLgIIPTSKS®it SCREWDRIVER STD. 2367 Nylon 50 Anchors, No. 6 x 1" screws,
BOX and No. 2 Phillips Driver Bit
with Drill Bit
CAT. • 100 CHROME PANHEAD ANCHORS

NO. D•E3S/C1R6”IPSTTIORNAIGHT SHANK BIT

2289 Wall-Dog Kit with Screwdriver 1 10
• 100 CHROME PANHEAD ANCHORS
340 2332 • 1 PHILLIPS® SCREWDRIVER

30 Wall-Dog Kit with Drill Bit 1 10

• 100 CHROME PANHEAD ANCHORS

• 3/16” STRAIGHT SHANK BIT T H E C O N S T R U C T I O N S U P P LY S P E C I A L I S T . . . W H E R E S E R V I C E C O M E S F I R S T

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
ADHESIVE ANCHORING SELECTION GUIDE

Anchor Category Injection Glass Capsule Anchor Bonding TOOLS &
Adhesive Adhesive Hardware Expansion Foam Sealant ACCESSORIES
Anchors Anchors

Product AC100+ Gold PE1000+ Gold Chem-Stud
Hammer-Capsule
Straight Cut CONTRACTOR
Anchor Rod SUPPLIES
Chisel Pointed
Anchor Rod
Internally
Threaded
Inserts
PowerFoam
TriggerFoam
PowerStick

Concrete n n n n n n n nnn

Lightweight Concrete n n oo n oo nnn

Base Material Grout-filled Concrete Masonry n n oo n oo nnn

Hollow Concrete Masonry n n n nnn

Solid Brick n n oo n oo nnn

Hollow Brick o n n nnn hangers
& strut
Stone o o oo n oo nnn

Structural Clay Tile o o n nnn

1/4" n

3/8" n n n n n n n

1/2" n n n n n n n fasteners &
threaded rod
5/8" n n n n n n n

Anchor Diameter 3/4" n n n n n n n

7/8" n n n n n n

1" n n n n n n

1 1/4" n n n o n n

1 3/8"

1 1/2"

1 3/4" concrete
anchors
Anchor 2" n nn
Chemistry Element Coated / Plated Carbon Steel

Type 304 Stainless Steel nn

Epoxy n

Ester Based Resin n nn specialty items
services & data
Polyurethane nn

MS Polymer n

n - Suitable
o - May Be Suitable

341
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
ADHESIVE ANCHORING SYSTEMS

AC100+™ GOLD

TOOLS & AC100+GOLD CARTRIDGES STD. STD.
ACCESSORIES BOX CTN. PALLET
CAT.
CONTRACTOR NO. DESCRIPTION 12 36 -
SUPPLIES 12 36 972
8462SD 5.0 oz. Push-Pak - 12 576
- 12 864
8478SD 10 oz. Quick Shot - 6 400

8480SD 8.0 oz. SBS

8486SD 12.0 oz. SBS
8490SD 29.0 oz. SBS

Mixing Nozzle Included AC100+GOLD MIXING NOZZLES STD. STD.
BOX CTN.
with each cartridge! CAT.
NO. DESCRIPTION 1-
Vinylester Injection Adhesive Anchoring System 1-
PRODUCT DESCRIPTION 8293 Extra Nozzle fo 5 oz., 8 oz., 10., oz. & 12 oz.
--
The AC100+Gold is a two-component vinylester injection adhesive system. 8281 Mixer Nozzle Extension, 8”
The system includes injection adhesive, mixing nozzles, dispensing tools,
steel brushes and handpump equipment (compressed air must be used for 8281 Mixer Nozzle for 29 oz.
larger size hardware). The AC100+Gold has been evaluated for uncracked
hangers concrete only and therefore cannot be used in moderate to high seismic design 8437
& strut categories. Suitable base materials include normal-weight concrete ranging
from 2,500 psi to 8,500psi.
fasteners & 8479
threaded rod
GENERAL APPLICATIONS AND USES 8484

• Structural connections, i.e., beam and column anchorage
• Evaluated for dry, wet and water-filled holes
• Suitable for uncracked concrete applications

FEATURES AND BENEFITS 8485

concrete • Consistent performance in high and low strength concrete 8494
anchors • Recognized for threaded rod and Grade 60 rebar hardware elements
• For use in 2500 to 8500 psi concretes
• Can be installed in a wide range of base material temperatures.
• Evaluated and recognized for freeze/thaw performance
• Evaluated and approved for several long-term and short-term loading temperature

ranges (see performance tables for applicable temperature ranges)

APPROVALS AND LISTINGS

• International Code Council, Evaluation Service (ICC-ES) ESR Pending

• Tested in accordance with AC308 criteria

• Evaluated and qualified by an accredited independent testing laboratory for use in

specialty items uncracked concrete AC100+GOLD MANUAL INJECTION DISPENSING TOOLS STD.
services & data • Strength design method according to AC308 and ACI 318 Appendix D CTN.
CAT. STD.
12
NO. DESCRIPTION BOX 6
6
GUIDE SPECIFICATIONS 8437 Manual Caulking Gun One Shot 1 20
1
CSI Divisions: 03151-Concrete Anchoring, 04081-Masonry Anchorage and 05090- 8479 High Performance Caulking Gun 1
Metal Fastenings. Adhesive anchoring system shall be AC100 Plus as supplied by Powers8484 1
Fasteners, Inc., Brewster, NY. 8 oz. Standard All Metal Manual 1
8485 8 oz. & 12 oz. High Performance Manual Tool

8494 29 oz. Std. All Metal Manual Tool 1

342
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
ADHESIVE ANCHORING SYSTEMS
TOOLS &
PE1000+ ACCESSORIES

PRODUCT DESCRIPTION CONTRACTOR
SUPPLIES
The PE 1000+ is a two-component epoxy injection adhesive system. The system includes
injection adhesive, mixing nozzles, dispensing tools, steel brushes and hand-pump hangers
equipment (compressed air must be used for larger size hardware). The PE 1000+ has been & strut
evaluated for uncracked concrete only and therefore cannot be used in moderate to high
seismic design categories. Suitable base materials include normal-weight concrete ranging
from 2,500 psi to 8,500psi.

GENERAL APPLICATIONS AND USES

• Structural connections, i.e., beam and column anchorage
• Dowelling applications that don’t transfer load to embedment dowels (splice)
• Suited for dry, wet and water-filled holes
• Suitable for uncracked concrete applications only

FREE NOZZLE

with EVERY 10, 15 & 20 OZ. CARTRIDGE!

FEATURES AND BENEFITS APPROVALS AND LISTINGS fasteners &
threaded rod
• Heavy duty anchoring system • International Code Council, Evaluation Service (ICC-ES) ESR Pending
• Consistent performance in high and low strength concrete • Tested in accordance with AC308 criteria
• Recognized for threaded rod and Grade 60 rebar • Evaluated and qualified by an accredited independent testing

hardware elements laboratory for use in uncracked concrete including wind loading
• For use in 2500 to 8500 psi concrete • Strength Design method according to AC308 and ACI 318
• Can be installed in temperatures down 41oF
• Evaluated and recognized for freeze/thaw performance Appendix D
• Evaluated and approved for long-term and short-term loading
GUIDE SPECIFICATIONS
(see performance tables for applicable temperature ranges)
CSI Divisions: 03151-Concrete Anchoring, 04081-Masonry
• Recognized for embedments up to 12 diameters Anchorage and 05090-Metal Fastenings. Adhesive anchoring
system shall be AC100+Gold anchors as supplied by Powers
Fasteners, Inc., Brewster, NY.

CARTRIDGE STD. STD. concrete
BOX CTN. PALLET anchors
CAT.
NO. DESCRIPTION 12 36 - 8295

500SD 13 oz.

CARTRIDGE SYSTEM NOZZLE STD. STD. MANUAL INJECTION DISPENSING TOOL STD. STD. specialty items
BOX CTN. BOX CTN services & data
CAT. CAT.
NO. DESCRIPTION 1- NO. DESCRIPTION 1 12
1-
7908 Extra Mixing Nozzle for PE1000+ 8295 Heavy Duty Dispensing Tool

7919 Mixer Nozzle Extension, 8”

343
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
ADHESIVE ANCHORING SYSTEMS

DISPENSING TOOLS AND accessories

TOOLS & REINFORCING BAR INSTALLATION TOOLS
ACCESSORIES
CHEM-STUD REBAR COUPLERS AND DRIVERS

CAT. STD. STD.
CTN.
NO. SIZE BOX
10
PNEUMATIC INJECTION TOOL DELIVERY SYSTEM 6533 #3 Coupler 1 5
10
CONTRACTOR CAT. STD. STD. 6534 #4 Coupler 1 10
SUPPLIES BOX CTN. 10
N8P4ON.1E3UMAD2TE2SICCoRzIPI.TNHIOiJgNEhCPTerIfOorNmaTnOceOPLneDumEaLtIiVc EToRoYl SYSTEM 6536 #6 Coupler 1 10
1 1 1
CAT. 6537 #7 Coupler 1 1
STD. STD. 1
8N4O.38 5DE6SoCRz.IPHTIiOgNh Performance Pneumatic Tool 6538 #8 Coupler 1
BO1X CTN1.
8496 30 oz. High Performance Pneumatic Tool 6539 #9 Coupler 1
1 1

6540 #10 Coupler 1

6590 Spline Driver Extension 1

6596 SDS-Max Driver Extension 1

hangers INTERNALLY THREADED INSERT TOOLS* STD. STD.
& strut CAT. BOX CTN.
NO. SIZE
11
6862 3/8"

6863 1/2" 11
6864 5/8" 11

BATTERY INJECTION DISPENSING TOOLS 6865 3/4" 11
NCBAOAT..TTERYDEISNCRJIPETCIOTNION DISPENSING TOOL
fasteners & STD. STD. *Use with drivers for threaded rod.
threaded rod CAT. BOX CTN.
STD. STD.
N84O.42 D2E2SCoRzI.PHTIiOgNh Performance Battery Tool 1 CTN.
BO1X
8444 30 oz. High Performance Battery Tool 1
1

concrete We carry a full Drive-In Type Capsule Adhesive
anchors assortment of PRODUCT DESCRIPTION
cleaning products,
accessories The Hammer-Capsule System consists of a self contained, single use, two-part glass
and supplies.
Turn to page 215 capsule into which threaded anchor rod or reinforcing bars can be directly driven

without the need for a chisel point or spinning action. It is designed for use in the

installation of 3/8" through 1" diameter threaded rod in solid concrete and

masonry materials. It can also be used to install reinforcing bars.

HAMMER-CAPSULE SELECTION GUIDE

CAT. *DRILL MIN. STD. STD.
NO. SIZE DIA. DEPTH BOX CTN.

6702 3/8" 7/16" 3-1/2" 10 500
10 200
6703 1/2" 9/16" 4-1/4" 10 100
5 50
6704 5/8" 11/16" 5" 5 50
5 50
specialty items 6705 3/4" 7/8" 6-5/8"
services & data
6706 7/8" 1" 7"

6707 1" 1-1/8" 8-1/4"

344
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
ADHESIVE ANCHORING SYSTEMS

ACCESSORIES

Adhesive installation accessories are designed to provide a dispenser or mixing Screen tubes are made from a 300 series stainless steel. The nominal diameter of TOOLS &
nozzle extension when required and to aid in the preparation of the anchor hole. the screen listed indicates the matching rod diameter. ACCESSORIES

STEEL BRUSHES STD. CAT. DESCRIPTION DRILL STD. CONTRACTOR
BOX NO. DIA. CTN. SUPPLIES
CAT. 1/4" x 6" Screen Tube †
NO. DESCRIPTION 1 7862 3/8” 25
1
7931 1/2" x 8-1/2" brush 1 7864 1/4" x 8" Screen Tube † 3/8” 25
1
7932 3/4" x 8-1/2" brush 1 7961 3/8" x 3-1/2" Screen Tube † 1/2” 25
1
7933 1" x 12" brush 1 7962 3/8" x 6" Screen Tube † 1/2” 25
1
7934 1-1/4" x 13" brush 1 7963 3/8" x 8" Screen Tube † 1/2” 25
1
7935 1-1/2" x 13-1/2" brush 1 7964 3/8" x 10" Screen Tube † 1/2” 25
8284 3/8” / #3 Steel Wire Brush* 1
8285 1/2” / #4 Steel Wire Brush* 1 7959 3/8" x 12" Screen Tube † 1/2” 25
8286 5/8” / #5 Steel Wire Brush* 1
8287 3/4” / #6 Steel Wire Brush* 1 7965 1/2" x 3-1/2" Screen Tube 5/8” 25
8288 7/8” / #7 Steel Wire Brush*
8289 1” / #8 Steel Wire Brush* STD. 7966 1/2" x 6" Screen Tube 5/8” 25
8290 1-1/4” Steel Wire Brush* BOX
8291 #10 Steel Wire Brush* 7967 1/2" x 8" Screen Tube † 5/8” 25
1
8293 SDS Plus Adapter for Steel Brush* 1 7968 1/2" x 10" Screen Tube † 5/8” 25 hangers
8292 Brush Extension, 12”* & strut
7969 5/8" x 4-1/2" Screen Tube 3/4” 20
HAND PUMP
7970 5/8" x 6" Screen Tube 3/4” 20
CAT.
NO. DESCRIPTION 7971 5/8" x 8" Screen Tube † 3/4” 20

8280 Hand Pump / Dust Blower 25 oz.* 7972 5/8” x 10” Screen Tube † 3/4” 20

8282 Air Nozzle with Extension* 7973 3/4” x 6” Screen Tube 7/8” 10

7977 3/4” x 8” Screen Tube 7/8” 10

7974 3/4” x 10” Screen Tube 7/8” 10

7975 3/4” x 13” Screen Tube 7/8” 10 fasteners &
threaded rod
7865 15/16” x 8” Screen Tube 1" 10

* Appropriate accessory for use with AC100+Gold and PE1000+Gold 7867 15/16” x 13” Screen Tube 1” 10

7869 15/16” x 17” Screen Tube † 1” 10

7955 Adhesive Shear Tube (steel sleeve) - 10

† Includes extension tubing

Anchor seal plugs help retain the adhesive in the anchor hole and hold the anchor The nominal diameter of the screen listed indicate the matching rod diameter. concrete
rod centered in the hole until the adhesive sets. The plugs are described by the NOTE: Hole size required for plastic screen tubes are different than that for the anchors
anchor rod diameter they are used with. stainless steel tubes.

CAT. DESCRIPTION PLUG HOLE STD. CAT. DESCRIPTION DRILL STD.
NO. DEPTH SIZE BAG NO. DIA. CTN
3/8" Anchor Seal Plug 3/8" x 3-1/2" Screen Tube
7936 1/2" Anchor Seal Plug 3/8" 7/16" 25 8474 1/2" x 3-1/4" Screen Tube 9/16” 25
7937 1/2" 9/16" 25 8475 1/2”x 4” Screen Tube 5/8” 25
8476 5/8” 25
For additional sizes call for availability.

specialty items
services & data

345
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
POWDER ACTUATED SELECTION GUIDE

TOOLS & Pin Category 0.300" Head Drive Pin 8mm Head Drive Pin Threaded Heavy
ACCESSORIES Product Studs Duty Pins

CONTRACTOR .300" Head
SUPPLIES Drive Pin
.300" Head Drive
Pin with Top Hat
.300" Head Drive
Pin with Washers
.300" Head Step
Shank Drive Pins
8mm Head
Drive Pin
8mm Head Drive
Pin with Top Hat
8mm Head Drive
Pin with 1" Washers
1/4" – 20
Threaded Stud
3/8" – 16
Threaded Stud
3/8" Head Drive Pin
10mm Head Drive Pin

Base Pin 1/2" 1 3/4" 1/2" 3/4" 2" 3/4" 5/8" 1 5/8" 5/8" 1" 2" 1/2" 3/4" 1" 3/4"
Material Dimensions to to to to to to to to to to to to to to to
Shank Length 1 1/2" 3" 1" 1 1/2" 3" 1" 1 1/2" 2 7/8" 1" 1 1/2" 2 7/8" 1 1/4" 1 1/4" 3 1/8" 3 1/4"

Shank Diameter 0.145" .145/.130" 0.145" 0.145" 0.205" .172", 0.177"
.216/.188"

Concrete n n n n n n n n n n n n n n n

Lightweight Concrete n n n n n n n n n n nnnn

Grout-filled Concrete Masonry n o o n o n o o o o oooo

Steel n nn nn nn nn nn

Gray – Power Level 1

Load Power Brown – Power Level 2
Level
hangers Green – Power Level 3
& strut
Yellow – Power Level 4

Red – Power Level 5

Purple/Black – Power Level 6

P3600 nn

PA351 o oo on oo

Powers Tools P3801 on nn

P3500 / PA3500 n n n n n n n n n n n n

P35s n nn nn nn

fasteners & P7201 n nn nn nn n
threaded rod
P2201 n n n n n n n n n n n n

P1000 n n n n n n n n n n n n

Hammer Drive Tool

721 n nn nn nn n

M70 n n n n n n n n n n n n

LADD (L1600)

D45 n n n n n n n n n n n n

D60 / D60L n n n n n n n n n n n n

MD380 nn

SA270 n n n n n n n n n n n n

Cobra n n n n n n n n n n n n

concrete Viper n nn n nn n
anchors
Other Tools DX E37 n nn nn nn n

DX E72 n n n n n n n n n n n n

DX400 n n n n n n n n n n n n

DX600N n no

DX35 n nn nn nn n

DX350 / DX351 n n n n n n n n n n n n

DX36M n n n n n n n n n n n n

DX 450

specialty items DX451 n n n n n n n n n n n n n n
services & data
DXA40 n nn nn nn n n

DXA41 o o o o o o o o o o o o n n n

DX100 n n n n n n n n n n n

DX200 n n n n n n n n n n n

DX460 o oo on oo

n - Suitable o - May Be Suitable

346

THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757 safety
products
POWDER ACTUATED SELECTION GUIDE

Pin Category Ballistic Specialty Clips and Powder Actuated Loads TOOLS &
Point Pin Fasteners Accessories ACCESSORIES

Product Ballistic Point Pin
Ballistic Point
Step Shank Pin CONTRACTOR
Forming Pin SUPPLIES
Hammer Drive Pin
Ceiling Clip Assemblies

(.300",8mm & Ballistic Point)

Ceiling Clip Assemblies

Ladd Tool (L1600)

BX – EMT Conduit Clip
Assemblies (.300"& 8mm)
Rebar Basket Clip
Assemblies (8mm)
.22 Caliber “A”
Single Load
.22 Caliber Single Loads

Ladd Tool (L1600)

.25 Caliber Disk Load
.25 Caliber Disk Loads

(Red)

.25 Caliber Single Load
.27 Caliber Single Loads
.27 Caliber Single
Long Loads
.25 Caliber 10
Load Strip
.27 Caliber 10
Load Strip (Purple/Black)
.27 Caliber Safety Strip

Base Pin 1/2" 1 3/4" 3/4" 1" 1" 1 1/4"
Material Dimensions to 1 1/4" 1 7/8" to to to 1 1/2" to to
Shank Length 7/8" 2 1/2" 3" 1 1/4" 1 1/4" 2 7/8"

Shank Diameter 0.150" 0.181"/0.150" 0.145" 0.140" 0.145" 0.155" 0.145" 0.145"

Concrete n n n n n n n n n

Lightweight Concrete n n n n n nn n

Grout-filled Concrete Masonry o o ooo oo

Steel n n o nnno n
Gray – Power Level 1 n

Load Power Brown – Power Level 2 nn n n hangers
Level Green – Power Level 3 & strut
Yellow – Power Level 4 n nn nn nn n
n nn nn nn n

Red – Power Level 5 n nnn nn n
Purple/Black – Power Level 6 n
nn n n
nn
P3600 n nn
nn
PA351 n nn n
n nn
Powers Tools P3801 nn

P3500 / PA3500 n n n n n n
P35s n n n
n n
P7201 n n
fasteners &
P2201 n n n n n threaded rod
P1000 n n n n n

Hammer Drive Tool n

721 n n nnn

M70 n n n n n nnn

LADD (L1600) nn

D45 n n n n n nn nn

D60 / D60L n n n n n nn n

MD380 n
n
SA270 n n n n n nn n
n nn n
Cobra n n n n nn n
nnn
Viper n n nnn concrete
n nn anchors
Other Tools DX E37 n n

DX E72 n n n n

DX400 nn n

DX600N n n

DX35 n n nn n
n
DX350 / DX351 n n n n n n n n

DX36M n n n n n n n nn
nn
DX 450
n
DX451 n n n n specialty items
services & data
DXA40 n n n nn n

DXA41 n n n n n n n

DX100 n n n n n n n

DX200 n n n n n n n n

DX460 n

n - Suitable o - May Be Suitable

347
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST

safety ( 800) 733-0089 • (781) 329-4000 • FAX: (781) 326-4757
products
POWDER ACTUATED TOOLS

TOOLS &
ACCESSORIES

P3500™

CONTRACTOR SIZE RANGE P35s™
SUPPLIES
1/2" to 3" pin lengths, .27 caliber SIZE RANGE

PRODUCT DESCRIPTION 1/2" to 1-1/2" pin lengths, .25 caliber

The PA3500™ is a modified version of the P3500 that includes a power adjuster,
allowing the operator to effectively decrease the power level of the load being used.
A red load can be toned down to the level of a green.

POWER ADJUSTER SETTINGS 3 6 PRODUCT DESCRIPTION
1
Medium Power Maximum Power The P35s™ is specially designed for acoustical and drywall contractors. It is a low
Minimum Power velocity, semi-automatic, tool which can be used to install .300 head drive pins,
8mm head drive pins and 1/4"-20 threaded studs up to 1-1/2" in total length. The
TECHNICAL DATA PIN LENGTH P35s™ is designed for high speed and repetitive volume applications. The standard
version of the tool is supplied with a flat end piston and a full size baseplate/guide.
TOOL BODY A limited access baseplate/guide assembly is also available.

hangers Precision Cast Aluminum 1/2" to 3" Total Length
& strut
TOOL LENGTH LOAD TYPE

13-5/8" .27 Caliber in a 10 Load Strip TECHNICAL DATA

TOOL WEIGHT POWER LEVEL TOOL BODY PIN LENGTH

5 lbs. Brown (2), Green (3), Yellow (4), Red (5) Precision Cast Aluminum 1/2" to 1-1/2" Total Length

PIN TYPE TOOL LENGTH LOAD TYPE

Ballistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin, 1/4"-20 11-1/4" .25 Caliber in a 10 Load Strip
Threaded Stud
TOOL WEIGHT POWER LEVEL

TYPICAL APPLICATIONS 4.25 lbs. Green (3), Yellow (4), Red (5)

TRADE APPLICATION PIN TYPE

fasteners & Acoustical Ceiling clip assemblies Ballistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin, 1/4"-20
threaded rod
Drywall Metal track, door frames Threaded Stud

Forming Concrete forms, basket clips, forming pins TYPICAL APPLICATIONS

Electrical Boxes, conduit clip assemblies TRADE APPLICATION

Mechanical Duct straps Acoustical Ceiling clip assemblies
Drywall Metal track, door frames
Residential Sill plates Electrical Boxes, conduit clip assemblies
Mechanical Duct straps
SELECTION GUIDE STD.
concrete CTN. SELECTION GUIDE STD.
anchors CAT CTN.
NO. DESCRIPTION 1 CAT
1 NO. DESCRIPTION 1
52019 PA3500 Powder Tool (Deluxe Kit) 1 1
52025 PA3500 Powder Tool (Blister Pack) 1 52002 P35s Tool (Deluxe Kit) 1
52103 PA Piston Flat End with Ring 1 52023 P35s Tool (Blister Pack) 1
52108 Guide 2/F-3 1 52200 Piston Standard 21/SDF 1
52110 Base Plate 2/S-13 1 52204 Guide 21/F3-1
52112 Piston Stop 1 52206 Baseplate 21/S1
52120 Shear Clip
52122 Steel Annular Ball

FOR APPLICATIONS IN TIGHT AREAS, A LIMITED ACCESS BASE PLATE/GUIDE IS AVAILABLE.

52114 Guide 2/F-4 Limited Access 1 Tool Operation

specialty items 52116 Baseplate 2/F-14-1 Limited Access 1 Powder actuated tools may be used only by properly
services & data trained and licensed operators as described in ANSI
POLE TOOLS FOR OVERHEAD ATTACHMENTS Standard A 10.3.

CAT STD. For complete tool operation details contact your
Newman represenative for training information.
NO. DESCRIPTION CTN.

50065 6’ Di-Electric Pole Tool 1

50066 8’ Di-Electric Pole Tool 1

52041 6’ Smacker Pole Tool (extension available) 1

52045 3’ Smacker Pole Extension 1

348
THE CONSTRUCTION SUPPLY SPECIALIST . . . WHERE SERVICE COMES FIRST