No. Form / Condition Size / Shape / Product Process Finishing / Surface Treatment HS Code References 5. Bars and rods, hotrolled, in irregularly wound coils, of other alloy steel. a. Irregularly wound coils; b. Solid cross-section in the shape of circles, segments of circles, ovals, rectangles, square, triangles or other convex polygons, flattened circles and modified rectangles; c. Two opposite sides are convex arcs, the other two sides being straight of equal length & parallel; d. May have indentations, ribs, grooves, or other deformations produced during the rolling process (reinforcing bars & rods). e. Known as wire rod. f. High speed steel products g. Silico-manganese steel products Hot-rolled No surface treatments 7227.10 7227.20 7227.90 CDO 2022 a. Chapter Note 1(l) to Chapter 72 b. Heading 72.27 to Chapter 72. EN HS 2022 a. Note 1(l) to Chapter 72, p. XV72-3 b. Heading 72.27, p. XV-7227-1, Mutatis mutandis to heading 72.13 6. (i) Other bars and rods of other alloy steel Other bars and rods a. Products which do not conform to any of the definition at Chapter Note 1(ij), (k) or (l) or to the definition of wire; b. Uniform solid crosssection along their whole length in the shape of circles, segments of circles, ovals, rectangles, a. Hot-rolling or forging blooms, billets, puddled bars or pilings; or b. Hot-drawing or hot-extrusion; c. Cold-forming or cold-finishing (such as colddrawn bars or grinded or sized bars) a. May have been subjected to working (such as drilling or sizing); b. Surface treatments (e.g. Oxide scale removal such as descaling, pickling; Rough coating / oxidizing or Removal of 7228.10 7228.20 7228.30 7228.40 7228.50 7228.60 CDO 2022 a. Chapter Note 1(m) to Chapter 72 b. Bars and rods other than Chapter Notes 1(l) & 1(m) to Chapter 72 c. Heading 72.28 to Chapter 72 88 TOPIC [ G ]
No. Form / Condition Size / Shape / Product Process Finishing / Surface Treatment HS Code References (ii) Angles, shapes and sections of other alloy steel square, triangles or other convex polygons, flattened circles and modified rectangles; c. More accurate & finished appearance; d. Sharp edges (square or rectangular); e. In straight lengths or folded in bundles; f. Rolled with protuberances or indentations (e.g. teeth, grooves, flanges); g. Individually twisted after rolling (e.g. steel twists); h. Having a single perforation to facilitate transportation. i. High speed steel products j. Silico-manganese steel products Angles, shapes and sections a. Uniform solid crosssection along their whole length, which do not conform to any of the definition at (ij), (k), (l) or (m) or to the definition of wire; b. H, I, T, capital omega, Z & U (including channels), obtuse, acute & right L angles; d. Finishing treatment. a. Hot-rolling, hotdrawing, hotextrusion hotforging or forging blooms or billets; b. Cold-formed or cold-finished (by cold-drawing); c. Forming on a roll type machines or by forming on a press. small portions of the metal for testing purposes) c. Further surface treatments (such as plating, coating or cladding); d. Straightening; Stamping, punching, printing with simple inscriptions such as trademarks & Metal flaws detection process a. Mechanical working (i.e. drilling, punching or twisting); b. Surface treatments (i.e. coating, plating or cladding). 7228.70 EN HS 2022 a. Note 1(m) to Chapter 72, p. XV-72-3 b. Bars and rods other than Chapter Notes 1(l) & 1(m) to Chapter 72, p. XV-72-3 c. Note (A) to Heading 72.28, p. XV-7228-1, Mutatis mutandis to heading 72.14 or 72.15 CDO 2022 a. Chapter Note 1(n) to Chapter 72 b. Heading 72.28 to Chapter 72 EN HS 2022 a. Note 1(n) to Chapter 72, p. XV-72-3 b. Note (A) to Heading 72.28, p. XV-7228-1, Mutatis mutandis to heading 72.16 89 SUB-CHAPTER IV : OTHER ALLOY STEEL; HOLLOW DRILL BAR AND RODS, OF ALLOY OR NON-ALLOY STEEL
No. Form / Condition Size / Shape / Product Process Finishing / Surface Treatment HS Code References (iii)Hollow drill bars and rods, of alloy steel c. The corners may be square or rounded; d. The limbs equal or unequal; e. The edges may or may not be bulbed. Hollow drill bars and rods a. Known as drill steel; b. Cross-sections are round, hexagonal, octagonal, or quarter octagonal; c. May be cut into short pieces for the manufacture of drill bits (heading 82.07); d. Lengths up to 5 or 6 metres; The hole down the length conducts liquid to the cutting point By piercing billets of non-alloy steel which are then rerolled. No surface treatment 7228.80 CDO 2022 a. Chapter Note 1(p) to Chapter 72 b. Heading 72.28 to Chapter 72. EN HS 2022 a. Note 1(p) to Chapter 72, p. XV-72-3 b. Note (B) to Heading 72.28, p. XV-7228-1 7. Wire of other alloy steel. a. In coils; b. Uniform solid crosssection along their whole length, which do not conform to the definition of flat-rolled products c. High speed steel products d. Silico-manganese steel products a. Drawing hotrolled bars and rods (heading 72.21) through a die; b. Cold-forming (e.g., Coldrolling). a. Wire which has been worked (e.g., by crimping) provided it does not thereby assume the character of articles or of products of other headings; b. Wire coated with a material such as textile; 7229.20 7229.90 CDO 2022 a. Chapter Note 1(o) to Chapter 72 b. Heading 72.29 to Chapter 72 EN HS 2022 a. Note 1(o) to Chapter 72, p. XV-72-3 b. Heading 72.29, p. XV-7229-1, Mutatis mutandis to heading 72.17 90 TOPIC [ G ]
World Customs Organization (2022), Explanatory Notes to HS2022, Chapter 72. Federal Gazette (2022), Customs Duties Order 2022, Government of Malaysia Federal Gazette (2023), Customs (Prohibition of Imports) Order 2023, Government of Malaysia Federal Gazette (2023), Customs (Prohibition of Exports) Order 2023, Government of Malaysia CIDB Malaysia (2018), Guidebook on Compliance of Mandatory Standards for Iron, Steel and Aluminium, Second Edition-2018. CIDB Malaysia (2015), Construction Industry Transformation Programme 2016-2020. Malaysia Steel Institute (2018), The Steel Advocate, Issue 2. Malaysian Iron and Steel Industry Federation. https://misif.org.my American Galvanizers Association (2023). What is Hot-Dip Galvanizing? https://galvanizeit.org/hot-dip-galvanized-steel-for-parking-structures/hot-dip-galvanizing About Mechanics (2023). What is Plastic Deformation? https://www.aboutmechanics.com/what-is-plastic-deformation.htm International Energy Agency (2020), Iron and steel technology roadmap-analysis. https://www.iea.org/energy-system/industry/steel Dmitri Kopeliovich (2013), Steel Strip Processing. www.subtech.com https://www.substech.com/dokuwiki/doku/steel_strip_processing LIST OF REFERENCES 91
Dmitri Kopeliovich (2013), Rolling. www.subtech.com https://www.substech.com/dokuwiki/doku/rolling Dmitri Kopeliovich (2013), Sputtering. www.subtech.com https://www.substech.com/dokuwiki/doku/sputtering Geology.com (2023) Metals: Articles about their properties, geology and use https://geology.com/metals International Iron Metallics Associations (2023). Metallic.org/pig-iron.html Keval Chaudhari (2016). Cold Working. https://www.engineersgallery.com/cold-working/ M. Rendy Yusman (2011), Hot Working of Metals https://sainsmechanical.blogspot.com/2011/12/hot-working-of-metals.html Precisionkiddsteel.com (2023). The Cold Drawing Process for Steel Bars and Wire https://www.precisionkidd.com/technology.htm The Library of Manufacturing. Metal Forging. https://thelibraryofmanufacturing.com Tata Steel Long Products Limited. Sponge iron. https://www.tatasteellp.com/product/sponge-iron/ Wikipedia. What is metal? https://en.wikipedia.org/wiki/metal Wikipedia. Deoxidization. https://en.wikipedia.org/wiki/dioxidization 92