Table Saw Vs Miter Saw – Which One Should You Get?

SAW

COMPARISON

table saw vs miter saw – Which One Should You Get?

When you take a look at table saws & miter saws at a glance, you will not be able to find any major
differences. But when you deep dive and focus on them, you will discover many differences. To make
your life easy, we thought of writing this article on table saw vs miter saw differences. It is up to you to
take a look at the differences and then decide what the best option available out there for you to
consider.

What is a table saw?

As the first part of table saw vs miter saw comparison, let’s take a look at what table saws are all about.
Table saws are flat tables containing saw blades incorporated into the tables, as seen in the diagram
below. This circular blade will have a slit that allows it to extend through into the table. Under the table
is a motor that can lift the blade up or down top of the table to facilitate cutting.
You set the bit of wood that has to cut just on table to begin. You should gently press the wooden piece
onto the spin blade each time the blade is switched on to make the cut. Until the item is chopped, you
would continue to manipulate and drive it via the saw.

Table saws aren't the best for making accurate cuts because of how they operate. Instead, they work far
ideal for general worked on smaller bits of wood as well as for general cutting, particularly through huge
amounts of wood.

Table saws play an essential component of most workshops, both expert and novice. They are utilized
for common cutting tasks, particularly for cutting through big chunks of wood. The board will be
effectively sliced through by the saw blade, while the table would offer the necessary support for
cutting.
Although table saws may be fixed or portable, they aren't the most mobile of tools. The majority of table
saws would be permanent, although certain occupations, like carpentry, use mobile table saws so they
may bring one to the work site.

What is a miter saw?

As the next part of the article, let’s figure out what a miter saw is. Then you can be fully aware about the
differences of table saw and miter saw. A miter saw may first seem to be precisely like such a table saw.
A miter saw often sits on top of a table and also comes with a blade that faces upward. Despite having a
similar appearance to a table saw, a miter saw is quite different. In actuality, the only similarities
between a miter saw and a table saw are the upward-facing blade and the ability to cut through wood.

A miter saw is not integrated to a table as a table saw is. It is only a machine that you may set down on a

table in its position. The swing arm of a miter saw is the most distinctive feature. To create the desired

cut, you may swing its arm upward or downward.

A miter saw's function is substantially different from that of a table saw, notwithstanding their
closeness. Miter saws were designed to correctly cut angles and serrated blades. It's simple to create
exact angles in your cuts thanks to the blade's swing-mounted design.
What are the differences between a table saw and a miter saw
As the next part of our table saw vs miter saw review, let’s do a one on one comparison in between
table saws and miter saws.

- Portability
Portability is one of the most important factors that you will need to consider in the table saw vs miter
saw comparison. Almost all table saws remain fairly big and cumbersome, despite the fact that some are
mobile. Using a table saw to cut huge pieces of timber in a single direction is simple but moving table
saws through one place to another may be difficult.
Miter saws are made expressly to be portable. You may place the miter saw within the back of the
vehicle and transport to go to and from the work sites since it is not physically linked to a table.

-Price
The majority of comparable products have a similar price. For table saws & miter saws, this is not true.
Table saws cost far more than others. Most table saws cost at least $1,200, but a nice miter saw may be
had for only a few hundred dollars.

-Cutting angle
The cutting angles are without a doubt the most important difference between the two saw kinds. Table
saws are intended for common, straight cuts, on the other hand. For instance, they are excellent for
cutting timber; in contrast, miter saws are perfect for fine cuts at various angles.
If all you need a saw for is general cutting, a table saw will do. But if you want to cut exact angles that
need accuracy and precision, you'll need a miter saw.

Benefits of miter saws
-Miter saws are portable

Most table saws were considered fixed and are fastened to cabinet or heavy legs made out of steel,

which make them a bit awkward, and challenging to move. However, some table saws comes on
wheeled stands that enable the user to transport them from location to location. Most miter saws weigh
between 50 and 60 pounds, making them light enough to be transported or put into the trunk of a

vehicle or a pickup truck. The miter saw may be made immovable by bolting it to a countertop that

cannot be moved if you plan to complete all of your woodworking tasks in a workshop.

-Blade breath would determine the cutting length

A miter saw cannot perform a cut longer than that of the length of blade because it is controlled by
lowering a rotating blade. The blade widths for miter saws are eight inches, ten inches, and twelve
inches. Broader material, including siding boards and substantial crown molding, need wider blades to
be cut. The miter saw with sliding arm is an exception to blade-width rule because it has a handle which
can be moved outward whereas the blade is whirling to create larger cuts. The blade of a table saw, on
either hand, is stationary or the timber is fed to blade, allowing it to cut whatever length of the board.
-You can easily cut bevels

A miter saw's head may be adjusted laterally to simultaneously cut a bevel and an angle off the edge of
a board, producing a slanted edge rather than a flat edge. At order to place trim in corners with a
smooth transition, beveled cuts are often employed in trim construction. In the same way that cutting
angles is more difficult on a table saw, cutting added layer is also more difficult. However, the blade of a
table saw may be changed from under the table and cut on a bevel. It takes expert carpentry skills to cut
bevels on a table saw; beginners in woodworking will have greater luck using a miter saw.
-You can easily cut angles

You can easily cut angles with the help of a miter saw. The word "miter" implies to connect two parts at
a 90° angle, like the manner the corners of a picture frame meet. A miter saw's head may be turned
from side to side can cut any required degree angle. As a result, miter saws are a need in the trim
carpentry sector because they can cut the intricate angles required for fitting trim and crown molding.
With a table saw, cutting angles is more challenging because the operator must keep the wood firm
while passing it through the rotating blade at the proper angle. You need to keep this in mind during
your table saw vs miter saw comparison as well.

Benefits of table saws

-You can cut large pieces of wood easily

A table saw has a flat surface that holds the wood while it is being cut. It is a great instrument for cutting
huge materials since the operator controls or pushes the wood, putting it into a revolving saw blade in
the middle of the table. A strip of wood, such as a trim board or siding plank, is placed on a small base at
the front of a miter saw, and the operator lowers the spinning blade manually through a handle housed
in a movable head to slice off the end of the strip.

-Table saws are flexible

Large chunks of wood cannot be cut with a miter saw, but almost any cut can be made with a table saw
—albeit with less accuracy. It's possible to buy a number of table saw accessories, including a miter
gauge in order to make cutting angles easier, but it's crucial to realize that although a table saw is highly
adaptable, cutting intricate shapes on it takes significant carpentry abilities. Novice woodworkers should
refrain from using a table saw to create angled or beveled cuts since doing so enhances their chance of
being hurt.

Uses of Miter Saw

Table saws are capable of fewer cut types than miter saws. They carry out combination cuts, bevel cuts,
angled cuts, and straight cuts. Miter saws are a popular option for many woodworkers due to their
multiple settings. Crown molding and concealed seams are created by craftsmen using bevel cuts. They
utilize angled cuts to generate edges that join together during exact angles and straight cuts for simple
scaling cuts that keep the square end of the wood. This is a prominent difference to note in table saw vs
miter saw comparison.
Miter saws need not finish rip cuts as table saws do. This tool cannot be used to drive wood through.
However, the miter saw makes exact, measured cuts by positioning the blade. Before dragging the blade
thru the wood surface, you adjust the machine's handles to achieve the angle or bevel you require.

Uses of table saw

With a table saw, you can cut in one of two ways. A rip cut is made when you slice a bit of wood against
the grain. A cross cut is when you cut the wood in half while cutting against the grain. You ought to be
able to perform this second sort of cut on a small bit of timber regardless of the table saw and miter saw
models that you use. A table saw's capacity to handle significantly longer and broader materials is what
gives it value.

A table saw can handle longer cuts even if it requires more space than a miter saw. The greatest table
saws or miter saws include additional shelves on each side of the blade, and when cutting even bigger
sheets or boards, you may utilize external supports. Table saws for the home and shop often have bigger
surfaces than table saws for workbenches. The work surface is strengthened by their sturdy bases,
which in many instances link to your dust control system to help clear the air.

Final words – What should you buy?

The answer to the question of how to select table saw vs miter saw for their workplaces relies on the
goals of starting woodworkers. If you're thinking about it, the machine you choose should deal with a
particular problem. Those that are starting from scratch with their shops may wish to begin with a miter
saw. These adaptable tools may be used for a variety of applications and perform many of the most
popular cuts.

Your choice of solution for table saw vs miter saw will rely on the area where you will get the most

advantage if you want to add to an already current collection of power tools. Although a work site table

saw increases your setup's adaptability, it best serves individuals who really need to spend some time

moving supplies. Many furniture makers prefer the extra pressure that comes with a fixed saw since

many jobs they work on at home don't call for this amount of mobility.

Top 6 Table Saw

1. DEWALT Table Saw for Jobsite, Compact, 8-1/4-Inch (DWE7485)
2 DEWALT 10-Inch Table Saw, 32-1/2-Inch Rip Capacity (DWE7491RS)
. Rockwell RK7323 BladeRunner X2 Portable Tabletop Saw
3 Skil SAW SPT99T-01 8-1/4 Inch Portable Worm Drive Table Saw
. Worx WX572L 5.5 Amp BladeRunner Portable Electric Table Top Saw
4 Goplus Table Saw, 10-Inch 15-Amp Portable Table Saw
Top.8 Miter Saw
15. DEWALT 12-Inch Miter Saw, 15-Amp, Single Bevel, Compound (DWS715)
2. . Metabo HPT 10-Inch Miter Saw | Single Bevel | Compound | 15-Amp Motor | C10FCGS
63. DEWALT 20V MAX 7-1/4-Inch Miter Saw, Tool Only, Cordless (DCS361B)
4. . BOSCH GCM12SD 15 Amp 12 Inch Corded Dual-Bevel Sliding Glide Miter Saw

5. DEWALT Miter Saw, 12-Inch, Double Bevel, Compound, XPS Cutline, 15-Amp
(DWS716XPS)
6. Skil 10" Dual Bevel Sliding Compound Miter Saw - MS6305-00

7. DEWALT Miter Saw, Single Bevel, Compound, 10-Inch, 15-Amp (DWS713)

8. Genesis GMS1015LC 15-Amp 10-Inch Compound Miter Saw