EPDM V2

 

J P Polymer Sheetings Limited

Butyl 

SPECIFICATION SHEET

Grade  B70    
Colour  BLACK    
Elastomer  BUTYL    
Quality  COMMERCIAL    
Hardness  Shore A ±5  60°  ISO 7619‐1 
SG (g/cm²)  1.23  ISO 2781 
Tensile (N/mm²)  8  ISO 37 
Elongation %  350  ISO 37 
Compression %  21  ISO 37 
Tear Strength  30  ISO 34‐1 
Abrasion mm³ 190  ISO 37 
Temperature (°C) from  ‐30 
Temperature (°C) to  115    

Roll Tolerances +/‐ 2%                         ISO 3302 SW1  Thicknesses available ● 
+/‐ 2%                         ISO 3302 SW1  1mm to 6mm  1.4m x10m   
Width tolerance:   
Length tolerance:   8mm to 25mm  1.4m x 5m 
Thickness
0.5– 1mm  +/‐ 0.2mm  32mm, 38mm,  1m x 1m    
1.5mm –3mm  +/‐ 0.3mm  40mm and 
4mm—5mm  +/‐ 0.4mm 
6mm  +/‐ 0.5mm  ●Items listed above usually ex stock.
8mm  +/‐ 0.7mm 
10mm—15mm  +/‐ 1mm  Other thicknesses and sizes available, please contact
20mm  sales office for your requirements
25mm  +/‐ 1.4mm 
+/‐ 1.75mm 
 
QUALITY ASSURED PRODUCTS WITH FULL TRACEABILITY

Care should be taken in selecting the most suitable quality for each application.
Advice is available but final responsibility remains with the customer.

Issue 1a March 2018 

 

J P Polymer Sheetings Limited

EPDM 

SPECIFICATION SHEET

Grade  E78   
  
Colour  BLACK   
  
Elastomer  EPDM  ISO 7619‐1 
ISO 2781 
Quality  WRAS APPROVED  1406512  ISO 37 
ISO 37 
Hardness  Shore A ±5  70°  ISO 37 
ISO 34‐1 
SG (g/cm²)  1.18  ISO 37 

Tensile (N/mm²)  11 

Elongation %  250 

Compression %  20 

Tear Strength  27 

Abrasion mm³

Temperature (° C) from  ‐40 

Temperature (°C) to  120   

Roll Tolerances +/‐ 2%                         ISO 3302 SW1  Thicknesses available ● 
+/‐ 2%                         ISO 3302 SW1  1mm to 6mm  1.4m x10m   
Width tolerance:   
Length tolerance:   8mm to 25mm  1.4m x 5m 
Thickness
0.5– 1mm  +/‐ 0.2mm  32mm, 38mm,  1m x 1m    
1.5mm –3mm  +/‐ 0.3mm  40mm and 
4mm—5mm  +/‐ 0.4mm 
6mm  +/‐ 0.5mm  ●Items listed above usually ex stock.
8mm  +/‐ 0.7mm 
10mm—15mm  +/‐ 1mm  Other thicknesses and sizes available, please contact
20mm  sales office for your requirements
25mm  +/‐ 1.4mm 
+/‐ 1.75mm 
 
QUALITY ASSURED PRODUCTS WITH FULL TRACEABILITY

Care should be taken in selecting the most suitable quality for each application.
Advice is available but final responsibility remains with the customer.

Issue 1a March 2018 

 

J P Polymer Sheetings Limited

EPDM 

SPECIFICATION SHEET

Grade  E78S   
  
Colour  BLACK   
  
Elastomer  EPDM  ISO 7619‐1 
ISO 2781 
Quality  WRAS APPROVED  1711567  ISO 37 
ISO 37 
Hardness  Shore A ±5  70°  ISO 37 
ISO 34‐1 
SG (g/cm²)  1.18  ISO 37 

Tensile (N/mm²)  11 

Elongation %  250 

Compression %  20 

Tear Strength  27 

Abrasion mm³

Temperature (° C) from  ‐40 

Temperature (°C) to  120   

Roll Tolerances +/‐ 2%                         ISO 3302 SW1  Thicknesses available ● 
+/‐ 2%                         ISO 3302 SW1  1mm to 6mm  1.4m x10m   
Width tolerance:   
Length tolerance:   8mm to 25mm  1.4m x 5m 
Thickness
0.5– 1mm  +/‐ 0.2mm  32mm, 38mm,  1m x 1m    
1.5mm –3mm  +/‐ 0.3mm  40mm and 
4mm—5mm  +/‐ 0.4mm  52mm 
6mm  +/‐ 0.5mm 
8mm  +/‐ 0.7mm  ●Items listed above usually ex stock.
10mm—15mm  +/‐ 1mm 
20mm  Other thicknesses and sizes available, please contact
25mm  +/‐ 1.4mm  sales office for your requirements
+/‐ 1.75mm 
 
QUALITY ASSURED PRODUCTS WITH FULL TRACEABILITY

Care should be taken in selecting the most suitable quality for each application.
Advice is available but final responsibility remains with the customer.

Issue 1a November 2017 

 

J P Polymer Sheetings Limited

EPDM 

SPECIFICATION SHEET

Grade  E79   
  
Colour  BLACK   
  
Elastomer  EPDM  ISO 7619‐1 
ISO 2781 
Quality  WRAS APPROVED  1604516  ISO 37 
ISO 37 
Hardness  Shore A ±5  80°  ISO 37 
ISO 34‐1 
SG (g/cm²)  1.17  ISO 37 

Tensile (N/mm²)  10 

Elongation %  250 

Compression %  30 

Tear Strength  30 

Abrasion mm³

Temperature (° C) from  ‐40 

Temperature (°C) to  120   

Roll Tolerances +/‐ 2%                         ISO 3302 SW1  Thicknesses available  
+/‐ 2%                         ISO 3302 SW1  1mm to 6mm  1.4m x10m   
Width tolerance:   
Length tolerance:   8mm to 25mm  1.4m x 5m 
Thickness
0.5– 1mm  +/‐ 0.2mm  32mm, 38mm,  1m x 1m    
1.5mm –3mm  +/‐ 0.3mm  40mm and 
4mm—5mm  +/‐ 0.4mm 
6mm  +/‐ 0.5mm  ●Items listed above usually ex stock.
8mm  +/‐ 0.7mm 
10mm—15mm  +/‐ 1mm  Other thicknesses and sizes available, please contact
20mm  sales office for your requirements
25mm  +/‐ 1.4mm 
+/‐ 1.75mm 
 
QUALITY ASSURED PRODUCTS WITH FULL TRACEABILITY

Care should be taken in selecting the most suitable quality for each application.
Advice is available but final responsibility remains with the customer.

Issue 1a March 2018 

 

J P Polymer Sheetings Limited

EPDM 

SPECIFICATION SHEET

Grade  E80E   
  
Colour  BLACK   
  
Elastomer  EPDM/SBR  ISO 7619‐1 
ISO 2781 
Quality  ECONOMY COMMERCIAL   ISO 37 
ISO 37 
Hardness  Shore A ±5  70°  ISO 37 
ISO 34‐1 
SG (g/cm²)  1.4  ISO 37 

Tensile (N/mm²)  3.5   

Elongation %  250 

Compression %    

Tear Strength    

Abrasion mm³

Temperature (° C) from  ‐30 

Temperature (°C) to  80 

Roll Tolerances +/‐ 2%                         ISO 3302 SW1  Thicknesses available ● 
+/‐ 2%                         ISO 3302 SW1  1mm to 6mm  1.4m x10m   
Width tolerance:   
Length tolerance:   8mm to 25mm  1.4m x 5m 
Thickness
0.5– 1mm  +/‐ 0.2mm  32mm, 38mm,  1m x 1m    
1.5mm –3mm  +/‐ 0.3mm  40mm and 
4mm—5mm  +/‐ 0.4mm 
6mm  +/‐ 0.5mm  ●Items listed above usually ex stock.
8mm  +/‐ 0.7mm 
10mm—15mm  +/‐ 1mm  Other thicknesses and sizes available, please contact
20mm  sales office for your requirements
25mm  +/‐ 1.4mm 
+/‐ 1.75mm 
 
QUALITY ASSURED PRODUCTS WITH FULL TRACEABILITY

Care should be taken in selecting the most suitable quality for each application.
Advice is available but final responsibility remains with the customer.

Issue 1a March 2018 

 

J P Polymer Sheetings Limited

EPDM 

SPECIFICATION SHEET

Grade  E80   
  
Colour  BLACK   
  
Elastomer  EPDM/SBR  ISO 7619‐1 
ISO 2781 
Quality  COMMERCIAL  ISO 37 
ISO 37 
Hardness  Shore A ±5  70°  ISO 37 
ISO 34‐1 
SG (g/cm²)  1.4  ISO 37 

Tensile (N/mm²)  5 

Elongation %  300 

Compression %  49 

Tear Strength    

Abrasion mm³

Temperature (° C) from  ‐30 

Temperature (°C) to  100   

Roll Tolerances +/‐ 2%                         ISO 3302 SW1  Thicknesses available ● 
+/‐ 2%                         ISO 3302 SW1  1mm to 6mm  1.4m x10m   
Width tolerance:   
Length tolerance:   8mm to 25mm  1.4m x 5m 
Thickness
0.5– 1mm  +/‐ 0.2mm  32mm, 38mm,  1m x 1m    
1.5mm –3mm  +/‐ 0.3mm  40mm and 
4mm—5mm  +/‐ 0.4mm 
6mm  +/‐ 0.5mm  ●Items listed above usually ex stock.
8mm  +/‐ 0.7mm 
10mm—15mm  +/‐ 1mm  Other thicknesses and sizes available, please contact
20mm  sales office for your requirements
25mm  +/‐ 1.4mm 
+/‐ 1.75mm 
 
QUALITY ASSURED PRODUCTS WITH FULL TRACEABILITY

Care should be taken in selecting the most suitable quality for each application.
Advice is available but final responsibility remains with the customer.

Issue 1a March 2018 

 

J P Polymer Sheetings Limited

EPDM 

SPECIFICATION SHEET

Grade  E81   
  
Colour  WHITE   
  
Elastomer  EPDM  ISO 7619‐1 
ISO 2781 
Quality  FOOD GRADE  ISO 37 
ISO 37 
Hardness  Shore A ±5  60°  ISO 37 
ISO 34‐1 
SG (g/cm²)  1.4  ISO 37 

Tensile (N/mm²)  6 

Elongation %  500 

Compression %  38 

Tear Strength  25 

Abrasion mm³ 200 

Temperature (° C) from  ‐40 

Temperature (°C) to  115   

Roll Tolerances +/‐ 2%                         ISO 3302 SW1  Thicknesses available ● 
+/‐ 2%                         ISO 3302 SW1  1mm to 6mm  1.4m x10m   
Width tolerance:   
Length tolerance:   8mm to 25mm  1.4m x 5m 
Thickness
0.5– 1mm  +/‐ 0.2mm  32mm, 38mm,  1m x 1m    
1.5mm –3mm  +/‐ 0.3mm  40mm and 
4mm—5mm  +/‐ 0.4mm 
6mm  +/‐ 0.5mm  ●Items listed above usually ex stock.
8mm  +/‐ 0.7mm 
10mm—15mm  +/‐ 1mm  Other thicknesses and sizes available, please contact
20mm  sales office for your requirements
25mm  +/‐ 1.4mm 
+/‐ 1.75mm 
 
QUALITY ASSURED PRODUCTS WITH FULL TRACEABILITY

Care should be taken in selecting the most suitable quality for each application.
Advice is available but final responsibility remains with the customer.

Issue 1a March 2018 

 

J P Polymer Sheetings Limited

EPDM 

SPECIFICATION SHEET

Grade  E84   
  
Colour  BLACK   
  
Elastomer  EPDM  ISO 7619‐1 
ISO 2781 
Quality  M228  ISO 37 
ISO 37 
Hardness  Shore A ±5  80°  ISO 37 
ISO 34‐1 
SG (g/cm²)  1.16  ISO 37 

Tensile (N/mm²)  10 

Elongation %  225 

Compression %  40 

Tear Strength  30 

Abrasion mm³

Temperature (° C) from  ‐35 

Temperature (°C) to  120   

Roll Tolerances +/‐ 2%                         ISO 3302 SW1  Thicknesses available ● 
+/‐ 2%                         ISO 3302 SW1  1mm to 6mm  1.4m x10m   
Width tolerance:   
Length tolerance:   8mm to 25mm  1.4m x 5m 
Thickness
0.5– 1mm  +/‐ 0.2mm  32mm, 38mm,  1m x 1m    
1.5mm –3mm  +/‐ 0.3mm  40mm and 
4mm—5mm  +/‐ 0.4mm 
6mm  +/‐ 0.5mm  ●Items listed above usually ex stock.
8mm  +/‐ 0.7mm 
10mm—15mm  +/‐ 1mm  Other thicknesses and sizes available, please contact
20mm  sales office for your requirements
25mm  +/‐ 1.4mm 
+/‐ 1.75mm 
 
QUALITY ASSURED PRODUCTS WITH FULL TRACEABILITY

Care should be taken in selecting the most suitable quality for each application.
Advice is available but final responsibility remains with the customer.

Issue 1a March 2018 

J P Polymer Sheetings Limited

-
-

– -
– -

— -
-
— -
-
-
-
-
-

GENERAL
INFORMATION

EPDM E 628 CHEMICAL
RESISTANCE

TABLE

EPDM, black – specification Hardness [Shore A]: 70 ±5 NR-SBR

drinking water gaskets KTW 1.3.13 D1 u. D2 cold Density [g/cm3]: 1.12
and warm water
Tensile strength [N/mm2]: 11
peroxidically cross-linked
Elongation at break [%]: 250
good weather and ozone resistant
Ozone resistance: good resistant
packaging see General Information
Weather resistance: good resistant PARA

Oil resistance: non resistant

Benzine resistance: non resistant

Acid resistance: good resistant

Strong bases: good resistant

Abrasion resistance: suitable

NBR

WORKING TEMPERATURE RANGE COMPRESSION SET DIN ISO 815 CR

Medium dyn. (stat.) max. short-term Duration Temperature CS
30 %
Air —40 (—50) °C +120 °C +140 °C 70 h 100 °C
+150 °C
Water – +120 °C

EPDM

AGEING DIN 53508 Strength Elongation OZONE RESISTANCE
Conditions Hardness ±20 % —40 % Duration pphm Ozone Temperature Crack Level
70 h/125 °C +10 Shore A
48 h 200 pphm 40 °C 0 SPECIALS

ROTA-CURED-SHEETS PRESS-CURED-SHEETS

Article- Thickness Width Length Surface No. of Article- Thickness Width Length Surface No. of FOOD- & DRINK-
ING WATER
number mm m m insert. number mm m m insert. GRADES
4011 03100 1.0 1.4 20 S S 0 4213 03100 10.0 1.4 5 S S 0

4011 03150 1.5 1.4 20 S S 0 S = smooth

4011 03200 2.0 1.4 20 S S 0

4011 03300 3.0 1.4 10 S S 0

4011 03400 4.0 1.4 10 S S 0

4011 03500 5.0 1.4 10 S S 0 INSULATING
MATTING
4011 03600 6.0 1.4 10 S S 0

4011 03800 8.0 1.4 5 S S 0

Please Note: 22.8.2003 INDUSTRIAL
MATTING
This catalogue has been carefully compiled to advise you, our customer, in the best possible way. The information, figures, test values and data correspond to actual engi-

neering standards and are the result of many years of tests and trials. As individual operation conditions influence the application of each product, the information supplied

in this catalogue can only be seen as a rough guideline. In every case it is the sole responsibility of the customer to evaluate his individual requirements, in particular whether

specified properties of our products are sufficient for the intended use. If there is any doubt (e.g. chemical resistance), do not hesitate to contact our qualified engineers. The

use of our products is at the user´s own risk. We do not have any influence concerning the application and individual usage. We do of course guarantee the quality of our pro-

ducts according to our general sales conditions, available on request.

Subject to alteration without prior notice – All mentioned properties contained in this catalogue are guiding values representing longterm experience average. WEAR
RESISTANT
Semperit Technische Produkte Gesellschaft m.b.H. & Co KG SHEETING
A-2632 Wimpassing, Triester Bundesstraße 26
Telefon +43 2630 310-0*, Telefax +43 2630 310 320
E-Mail: semperflex@semperit.at, Internet: www.semperit.at

GENERAL
INFORMATION

EPDM E 4580 CHEMICAL
RESISTANCE

TABLE

EPDM, black – high grade Hardness [Shore A]: 50 ±5 NR-SBR

high quality, 50 Shore, cross-linked by sulphur Density [g/cm3]: 1.05

good weather and ozone resistant Tensile strength [N/mm2]: 8

meets various automotive standards, Elongation at break [%]: 500
e.g. VW 2.8.1 G50, please contact our sales
office for particular confirmations for specific Ozone resistance: good resistant
automotive standards
Weather resistance: good resistant PARA
feather white dusting
Oil resistance: non resistant
packaging see General Information
Benzine resistance: non resistant

Acid resistance: resistant

Strong bases: good resistant

Abrasion resistance: moderately suitable

NBR

WORKING TEMPERATURE RANGE COMPRESSION SET DIN ISO 815 CR

Medium dyn. (stat.) max. short-term Duration Temperature CS
45 %
Air —40 (—50) °C +100 °C +120 °C 22 h 100 °C 25 %
+130 °C
Water – +110 °C 22 h 70 °C

EPDM

AGEING DIN 53508 OZONE RESISTANCE
Conditions Hardness Strength Elongation Duration pphm Ozone Temperature Crack Level
70h/100 °C +5 Shore A —10 % —30 %
48 h 200 pphm 40 °C 0 SPECIALS

ROTA-CURED-SHEETS PRESS-CURED-SHEETS
Article- Thickness Width Length Surface No. of
Article- Thickness Width Length Surface No. of FOOD- & DRINK-
ING WATER
number mm m m insert. number mm m m insert. GRADES
4011 58100 1.0 1.4 20 S S 0 4213 58100 10.0 1.4 5 S S 0
4213 58120
4011 58150 1.5 1.4 20 S S 0 12.0 1.4 5 S S 0

4011 58200 2.0 1.4 20 S S 0 4213 58150 15.0 1.4 5 SS 0
4213 58200 20.0 1.4 5 SS 0
4011 58300 3.0 1.4 10 S S 0 4213 58250 25.0 1.4 5 SS 0

4011 58400 4.0 1.4 10 S S 0

4011 58500 5.0 1.4 10 S S 0 4213 58300 30.0 1.4 5 SS 0 INSULATING
4213 58400 40.0 1.4 5 SS 0 MATTING
4011 58600 6.0 1.4 10 S S 0

4011 58800 8.0 1.4 5 S S 0 S = smooth

Please Note: 22.8.2003 INDUSTRIAL
MATTING
This catalogue has been carefully compiled to advise you, our customer, in the best possible way. The information, figures, test values and data correspond to actual engi-

neering standards and are the result of many years of tests and trials. As individual operation conditions influence the application of each product, the information supplied

in this catalogue can only be seen as a rough guideline. In every case it is the sole responsibility of the customer to evaluate his individual requirements, in particular whether

specified properties of our products are sufficient for the intended use. If there is any doubt (e.g. chemical resistance), do not hesitate to contact our qualified engineers. The

use of our products is at the user´s own risk. We do not have any influence concerning the application and individual usage. We do of course guarantee the quality of our pro-

ducts according to our general sales conditions, available on request.

Subject to alteration without prior notice – All mentioned properties contained in this catalogue are guiding values representing longterm experience average. WEAR
RESISTANT
Semperit Technische Produkte Gesellschaft m.b.H. & Co KG SHEETING
A-2632 Wimpassing, Triester Bundesstraße 26
Telefon +43 2630 310-0*, Telefax +43 2630 310 320
E-Mail: semperflex@semperit.at, Internet: www.semperit.at

51

GENERAL
INFORMATION

EPDM E 9566 CHEMICAL
RESISTANCE

TABLE

EPDM, black – high-grade Hardness [Shore A]: 70 ±5 NR-SBR

excellent ratio of price and performance, Density [g/cm3]: approx. 1.30
cross-linked by sulphur
Tensile strength [N/mm2]: 7
good weather and ozone resistant
Elongation at break [%]: 250
meets various automotive standards,
e.g. VW 2.8.1 G70, please contact our sales Ozone resistance: good resistant
office for particular confirmations for specific
automotive standards Weather resistance: good resistant PARA

packaging see General Information Oil resistance: non resistant

Benzine resistance: non resistant

Acid resistance: resistant

Strong bases: good resistant

Abrasion resistance: moderately suitable

NBR

WORKING TEMPERATURE RANGE COMPRESSION SET DIN ISO 815 CR

Medium dyn. (stat.) max. short-term Duration Temperature CS
+120 °C 35 %
Air (—40) °C +100 °C 22 h 70 °C

EPDM

AGEING DIN 53508 Strength Elongation OZONE RESISTANCE
Conditions Hardness —10 % —25 % Duration pphm Ozone Temperature Crack Level
70 h/100 °C +10 Shore A
48 h 200 pphm 40 °C 0 SPECIALS

ROTA-CURED-SHEETS PRESS-CURED-SHEETS
Article- Thickness Width Length Surface No. of
Article- Thickness Width Length Surface No. of FOOD- & DRINK-
ING WATER
number mm m m insert. number mm m m insert. GRADES
4011 66100 1.0 1.4 20 S S 0 4213 66120 12.0 1.4 5 S S 0
4213 66150
4011 66150 1.5 1.4 20 S S 0 15.0 1.4 5 S S 0

4011 66200 2.0 1.4 20 S S 0 4213 66200 20.0 1.4 5 SS 0

4011 66300 3.0 1.4 10 S S 0 4213 66250 25.0 1.4 5 SS 0

4011 66400 4.0 1.4 10 S S 0 4213 66300 30.0 1.4 5 S S 0

4011 66500 5.0 1.4 10 S S 0 4213 66400 40.0 1.4 5 S S 0 INSULATING
MATTING
4011 66600 6.0 1.4 10 S S 0 4213 66500 50.0 1.4 5 SS 0

4011 66800 8.0 1.4 5 S S 0 S = smooth

4011 66000 10.0 1.4 5 SS 0

Please Note: 22.8.2003 INDUSTRIAL
MATTING
This catalogue has been carefully compiled to advise you, our customer, in the best possible way. The information, figures, test values and data correspond to actual engi-

neering standards and are the result of many years of tests and trials. As individual operation conditions influence the application of each product, the information supplied

in this catalogue can only be seen as a rough guideline. In every case it is the sole responsibility of the customer to evaluate his individual requirements, in particular whether

specified properties of our products are sufficient for the intended use. If there is any doubt (e.g. chemical resistance), do not hesitate to contact our qualified engineers. The

use of our products is at the user´s own risk. We do not have any influence concerning the application and individual usage. We do of course guarantee the quality of our pro-

ducts according to our general sales conditions, available on request.

Subject to alteration without prior notice – All mentioned properties contained in this catalogue are guiding values representing longterm experience average. WEAR
RESISTANT
Semperit Technische Produkte Gesellschaft m.b.H. & Co KG SHEETING
A-2632 Wimpassing, Triester Bundesstraße 26
Telefon +43 2630 310-0*, Telefax +43 2630 310 320
E-Mail: semperflex@semperit.at, Internet: www.semperit.at

GENERAL
INFORMATION

CHEMICAL EPDM E 9614
RESISTANCE

TABLE

NR-SBR EPDM, black – high-grade Hardness [Shore A]: 70 ±5

excellent ratio of price and performance Density [g/cm3]: 1.22

peroxidically cross-linked, only small decrease of Tensile strength [N/mm2]: 9
physical values at high temperatures
Elongation at break [%]: 200
good weather and ozone resistant
Ozone resistance: good resistant
meets various automotive standards,
PARA e.g. VW 2.8.1 G70, please contact our sales Weather resistance: good resistant
office for particular confirmations for specific
automotive standards Oil resistance: non resistant

packaging see General Information Benzine resistance: non resistant

Acid resistance: resistant

Strong bases: good resistant

Abrasion resistance: moderately suitable

NBR

CR WORKING TEMPERATURE RANGE COMPRESSION SET DIN ISO 815

Medium dyn. (stat.) max. short-term Duration Temperature CS
+140 °C 25 %
Air (—40) °C +120 °C 22 h 100 °C

EPDM

AGEING DIN 53508 Strength Elongation OZONE RESISTANCE
Conditions Hardness —10 % —20 % Duration pphm Ozone Temperature Crack Level
70 h/125 °C +5 Shore A
SPECIALS 48 h 200 pphm 40 °C 0

ROTA-CURED-SHEETS PRESS-CURED-SHEETS
Article- Thickness Width Length Surface No. of
FOOD- & DRINK- Article- Thickness Width Length Surface No. of
ING WATER
GRADES number mm m m insert. number mm m m insert.
4101 64050 0.5 1.4 20 S S 0 4213 64100 10.0 1.4 5 S S 0
4213 64120
4011 64100 1.0 1.4 20 S S 0 12.0 1.4 5 S S 0

4011 64150 1.5 1.4 20 S S 0 4213 64150 15.0 1.4 5 S S 0
4213 64200 20.0 1.4 5 S S 0
4011 64200 2.0 1.4 20 S S 0 4213 64250 25.0 1.4 5 S S 0

4011 64300 3.0 1.4 10 S S 0

INSULATING 4011 64400 4.0 1.4 10 S S 0 4213 64300 30.0 1.4 5 S S 0
MATTING 4213 64400 40.0 1.4 5 S S 0
4011 64500 5.0 1.4 10 S S 0

4011 64600 6.0 1.4 10 S S 0 S = smooth

4011 64800 8.0 1.4 5 S S 0

INDUSTRIAL Please Note: 22.8.2003
MATTING
This catalogue has been carefully compiled to advise you, our customer, in the best possible way. The information, figures, test values and data correspond to actual engi-

neering standards and are the result of many years of tests and trials. As individual operation conditions influence the application of each product, the information supplied

in this catalogue can only be seen as a rough guideline. In every case it is the sole responsibility of the customer to evaluate his individual requirements, in particular whether

specified properties of our products are sufficient for the intended use. If there is any doubt (e.g. chemical resistance), do not hesitate to contact our qualified engineers. The

use of our products is at the user´s own risk. We do not have any influence concerning the application and individual usage. We do of course guarantee the quality of our pro-

ducts according to our general sales conditions, available on request.

WEAR Subject to alteration without prior notice – All mentioned properties contained in this catalogue are guiding values representing longterm experience average.
RESISTANT
SHEETING Semperit Technische Produkte Gesellschaft m.b.H. & Co KG
A-2632 Wimpassing, Triester Bundesstraße 26
Telefon +43 2630 310-0*, Telefax +43 2630 310 320
E-Mail: semperflex@semperit.at, Internet: www.semperit.at

FLAME PROTECTION

EPDM E 2441

General: Properties:
EPDM, black - high-grade
sulfur linked Hardness [Shore A]: ISO 7619-1 60 ±5
good weather and ozone resistant ca. 1,12
no discolouring Density [g/cam³]: ISO 118 7
Flame resistant classification from 2 to 10 mm thickness
according DIN EN 45545 part 2 : 2016-02 Tensile strength ISO 37-S2 300
for sealing profiles and gaskets application use R22/R23, [N/mm²]: 350
class HL2/HL3 6
complies with flame classification according EU regulation 95/28/EG and Elongation at break [%]: ISO 37-S2 EN 45545-2
US-FMVSS 302
wrapping: stretched foil, labelled Abrasion [mm³] ISO 4649 method A
standard finishing in seperation foil
Tear resistance [N/mm] ISO 34-1 method A
*PAH - REACH-conform in accordance with EU 1272/2013
flame reaction R22/HL2

  R23/HL2

Working temperature range Stabilities:

Medium dyn. (stat.) max. short-term Ozone resistance: good resistant
+100 °C +120 °C Weather resistance: good resistant
air (-35) °C Oil resistance: non resistant
CS Fuel resistance: non resistant
Compression set DIN ISO 815 +40 % Acid resistance: resistant
Strong bases: good resistant
Duration Temperature Crack Level Abrasion resistance: moderately suitable
0
24 h +70 °C
Elongation
Ozone resistance pphm ozone Temperature 25 %
50 pphm 40 °C
Duration

96h

Ageing ISO 1817 Hardness Strength
+10 Shore A - 20 %
Conditions

22 h / 100°C

ROTACURED Thickness Width Length
SHEETS
mm mm mm
product number 2,00 1.400 20.000
401124200 3,00 1.400 10.000
401124300 4,00 1.400 10.000
401124400 5,00 1.400 10.000
401124500 6,00 1.400 10.000
401124600 8,00 1.400 5.000
401124800 10,00 1.400 5.000
401124000

PAH disclaimer: Please note:
Referring to an international proficiency test and information received from the testing laboratories This datasheet has been carefully compiled to advise you, our customer, in the best possible way.
about accuracy of test results we may inform you, that test results for the same specimen from The information, figures, test values and data correspond to actual engineering standards and are
different laboratories may not correlate: the result of many years of tests and trials. As individual operation conditions influence the
• results of the 10 PAH with individual limits of < 1 mg/kg in the measurement range around the limit application of each product, the information supplied in this datasheet can only be seen as a rough
are only accurate to approx. +/- 70% guideline. In every case it is the sole responsibility of the customer to evaluate his individual
• results of the overall limit of < 50 mg/kg are only accurate to approx. +/- 35% requirements, in particular whether specified properties of our products are sufficient for the
Our test results are provided on an as-is basis and to the best of our knowledge, without any legally intended use. If there is any doubt (e.g. chemical resistance), do not hesitate to contact our qualified
binding commitment. Our tests do not release you from own tests as to the respective application engineers. The use of our products is at the user’s own risk. We do not have any influence
envisaged. concerning the application and individual usage. We do of course warrant the quality of our
products according to our General Sales Conditions, available on our website
www.semperitgroup.com or on request.

Subject to alteration without prior notice: In order to always have the latest product- and safety information make sure you visit our website (www.semperitgroup.com) regularly or contact specialist dealers
or a Semperit application engineer. Additional important general information about the range, storage and tolerances can also be found at our website (www.semperitgroup.com) and must be followed
without exception.

Date: 06.09.2018

Care should be taken in selecting the most suitable quality for each
application. Advice is available but final responsibility remains with the customer.

Our economy grades are made to a very high standard and made with similar
properties to the standard grades, they contain a much lower base polymer content,

so can sometimes be used as a cheaper, less hard wearing solution.

The information, figures, calculations, test values and data contained in this brochure
- which we use to best advise our customers - correspond to current engineering
standards. This data is results of long years of tests and trials.

As individual operation conditions influence the application of each sheet, the
information in this brochure can only be seen as a rough guideline. In the individual

case it is the sole responsibility of the customer to evaluate requirements, in
particular if specified properties are sufficient for use.

As we cannot have any influence over how our products are used, they are used
entirely at the user's own risk.

We do of course guarantee the quality of our products according to general sales
conditions, available on request. Subject to change and error. The mentioned
properties are guiding values

Samples are available on request, to enable you to carry out your own tests for
suitability.

Unit 26 Coneygre Industrial Estate,
Birmingham New Road,
Tipton,
West Midlands.
DY4 8XP

(For Sat Nav use DY4 8JW)
Tel: 0121 520 5020
Fax: 0121 522 4610